Boca Flasher LUMELINE Installation Manual
Boca Flasher LUMELINE is a versatile lighting solution designed for both indoor and outdoor use. With its anodized aluminum housing and durable finish, it is weather and abrasion-resistant, making it suitable for damp or wet locations. The line voltage fixture eliminates the need for secondary transformers, simplifying installation. It offers a range of mounting options with fixed, swivel, 3" arc, and 6" arc brackets, allowing for flexible positioning. The fixtures can be connected in a series, with a maximum of 200ft per 20A breaker or 150ft per 15A breaker.
Advertisement
Advertisement
Installation Manual
LUMELINE
WARNING: Do Not lIft fIxtuRe by cAbles.
This could result in permanent damage to both the fixture and the cables. Damage resulting from grasping cables and/or putting undue pressure on the cable connections will not be covered under the warranty! Do not attempt to install or use the LUMELINE fixture without reading the installation instructions and safety labels completely. Failure to adhere to these instructions could result in serious injury or property damage. Do not modify, alter or attempt to service the LUMELINE. Doing so will void the warranty.
Installation Instructions
LUMELINE
Indoor | outdoor Shallow Profile line Voltage
Introduction:
The Boca LUMELINE is a line voltage fixture that eliminates the need for secondary transformers, making installation contractor friendly.
The housing is anodized aluminum with a durable finish making it weather and abrasion resistant. It is UL Listed for dry, damp or wet location
(model dependent). See layout drawings for model provided.
Maintenance:
CleanIng Dry and Damp (IP65) Rated Fixtures: To clean surface use a soft damp cloth.
Wet (IP68) Rated Fixtures: To clean surface use a soft cloth with mild soap and water.
Storage Store in a dry, well-ventilated area when product is not in use.
Keep the electrical cord away from heated surfaces when in use or not in use.
If cord shows signs of damage do not use, return product to manufacturer.
electrical specifications:
1. Input Voltage: 90-120VAC
2. Total linear ft per 20A breaker: 200ft
3. Total linear ft per 15A breaker: 150ft
4. Input Current: Model dependent
IP65
DAMP LISTING
IP68
WET LISTING
Model Dependent
Max temp: 55C
Min. temp: -40C
Fixtures must be installed by a qualified and licensed electrician in accordance with all national, state and local electrical codes and regulations. If any part of this manual does not meet the necessary codes and regulations, contact the factory for more information before attempting to install.
turn Power off At circuit breaker before beginning Installation!
INcluDeD IN thIs PAckAGe:
1
LUMELINE Fixtures
(In lengths shown on job specific drawings)
2
Mounting Brackets
(2 brackets per fixture)
Fixed or
Swivel
3
Job Specific Drawings
Power cord length is
6.5 ft. per UL standard
3" Arc
6" Arc or
Page 2 oF 6
LUMELINE
Installation Instructions
LUMELINE
1. INstAll clIPs INto substRAte
Fixed Clips Swivel Clips
1b
1a 1a
1b
Install security screw using supplied screw and driver.
3” Arc & 6” Arc Bracket Installation
1a 1b
Screw Information:
1. Screws not provided by Boca Flasher.
2. Boca Flasher recommends wide washer flat head Philips #8 screw
(not to exceed .418” in diameter).
3. Length of screw will vary depending on mounting surface.
4. For outdoor installations, installer should use a screw with weatherproof coating.
2. INstAll fIxtuRe INto clIPs
2a Place the notch on the clip into the first notch of the fixture.
2b Fixture will pivot on notch as it is pushed down.
2c
Clip will securely snap into place.
2d
If using the Swivel Clip or Arc Bracket loosen the screw where the clip and swivel bracket meet to adjust angle of the fixture.
▶
Second Notch
▶ ▶
De te nt snap!
▶
Page 3 oF 6
Angle
Screw
▶
Installation Instructions
LUMELINE
3.
1
coNNect fIxtuRes toGetheR
aS Shown on joB SPeCIFIC drawIngS
3a
Rotate fixture to see bottom and note each label.
3b
Cross-reference with job specific drawing.
3 c Connect Male and Female end caps in order shown on job specific drawings.
▶
▶
BF-01
▶
◀
Labels on fixtures correspond with nomenclatures on drawings.
▶
▶
LUMELINE
3 d
Push together until it locks.
I MPORtAnt nOtE:
Not screwing fixtures together represents an incomplete install and voids the warranty. If any fixtures are damaged as a result of improper installation.
3.2
coNNect fIxtuRes toGetheR
twISt loCK ConneCtIon
3a See above for information on determining layout.
3c
Push together and then twist until completely connected and sealed if outdoors.
3b Connect Male and Female twist lock cables in order shown on job specific drawings.
* Add tape to twist locks.
Place thumb over tape at starting point and
PULL around connector area until tape overlaps itself.
* For weather-tight applications only
See additional instructions for weather-tight tape
Page 4 oF 6
4. coNNect fIxtuRes to PoWeR
Installation Instructions
LUMELINE
5. coNNect to A DIMMING systeM
*note: These fixtures can dim on forward (leading) or reverse (trailing) phase dimmers. Boca Flasher does not recommend the use of a “Smart” or phase-adaptive dimming module.
6. ReMoVING fIxtuRes fRoM clIPs
IF neCeSSarY
6a Slide a flat head screwdriver in between the clip and fixture.
6b While holding the fixture with your other hand, pull back on screwdriver to release from notch.
6c Once released from one notch, fixture can be fully removed.
Page 5 oF 6
Installation Instructions
LUMELINE
IMPoRtANt sAfety ReMINDeRs:
1. DANGER:
To reduce the risk electric shock, always unplug the LUMELINE from electrical outlet before cleaning. Cut breaker if outlet is not available.
2. To reduce the risk of burns, fire, electric shock or injury to persons:
• Use the LUMELINE only for its intended use as described in these instructions.
• Do not use attachments not recommended by Boca Flasher.
• Never operate the LUMELINE if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. If the seal appears to be damaged/broken/torn return the LUMELINE to a service center for examination or repair.
• Keep cord away from heated surfaces.
• Never drop or insert any object into any opening.
• Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
3. WARNING:
Do not attempt to install or use the LUMELINE without reading the installation instructions and safety labels. Failure to adhere to these instructions could result in serious injury or property damage.
4. Do not modify, alter or attempt to service the LUMELINE:
Doing so will void the warranty.
5. Do not use sharp tools near or on the fixture lens:
Doing so will result in property damage and void the warranty.
Boca Flasher, Inc.
508 S. Military trail n deerfield Beach, Florida n 33442 USa
Phone: 561-989-5338 n Fax: 561-982-8323 www.bocaflasher.com
We are constantly improving our fixtures and reserve the right to change options and specifications. Additional information & details at www.bocaflasher.com. For specific requirements, contact your Boca Flasher sales representative. Boca Flasher, Inc. 508
S. Military Trail, Deerfield Beach, Florida 33442 USA Phone: 561.989.5338 Fax: 561.982.8323 © 2017 Boca Flasher, Inc. All rights reserved. All names and trademarks are property of their respective owners. REV 07-2017
IP65
DAMP LISTING
IP68
WET LISTING

Public link updated
The public link to your chat has been updated.
Advertisement