MAN CPP7500E ENG - Cobra Electronics Corporation Home
CPP 7500 E
User Manual
Portable Power - Anytime, Anywhere!
Thank for purchasing the Cobra CPP 7500 E JumPack™
jump starter portable PowerPack. Before using this product,
please read these instructions carefully to learn about the
features and capabilities of the JumPack and how you can
get the best out of it.
Note: Please charge your CPP 7500 E JumPack completely
prior to using it for the first time.
©2014 Cobra Electronics Corp. Part No. 480-977-P Printed in China Version A
CPP7500E_MANL_ENG.indd 1
Failure to follow instructions can result in personal injury or
product damage.
Charge the JumPack fully prior to use.
WARNING: Keep the unit clear of fire and water.
WARNING: Shock Hazard. Keep away from children. Do not
insert foreign objects into the jumper cables port/jack, the USB
output port, or the DC input jack. Do not expose this product to
water, rain, snow, condensation, or spray. Do not open the
JumPack. No user replaceable parts are inside the JumPack.
WARNING: Explosion Hazard. Do not use this product where
there are flammable fumes or gases, such as in the bilge of a
gasoline-powered boat, or near propane tanks.
The jump start cable clamps must be connected positive to
positive (red clip to battery (+)) and negative to negative (black
clip to battery (-)). A reverse polarity connection (positive to
negative) may cause damage to the JumPack and/or create a
sparking/explosion hazard.
WARNING: Fire Hazard. Do not crush or puncture the JumPack.
Never allow the jump start cables’ red and black clamps’ metal
contacts to touch each other or another common metal
conductor. This could cause damage to the unit and/or create a
fire hazard. Always disconnect the jump start cables from the
JumPack after each use and store separately. The jump start
feature is designed for short term operation only. Turn the ignition
key for no more than 3 seconds at a time. Operating the jump
start feature for more than 3 seconds may cause damage to the
unit. Allow the JumPack to cool down for at least 1 minute after
each jump start attempt.
Caution: Operating temperature
Do not expose the JumPack to temperatures over +113° F (+45° C) or
under -14° F (-10° C). Using the JumPack at high or low temperatures
may reduce the internal battery capacity and shorten the battery life.
Note: In extreme cold weather conditions, please bring the JumPack
indoors for best results.
Precautions when working with batteries
WARNING: Explosion and fire hazard
1. Follow all instructions published by the battery manufacturer and
the manufacturer of the equipment in which the battery is installed.
2. Make sure the area around the battery is well-ventilated.
3. Never smoke or allow a spark or flame in the vicinity of the engine
or batteries.
4. Be careful not to drop a metal object on the battery or allow a metal
tool to simultaneously touch the positive and negative cable ends or
battery terminals.
5. Remove personal metal items such as rings, bracelets, necklaces,
and watches when working with batteries. Batteries produce a
short-circuit current high enough to weld a ring or other similar
objects to metal, causing a severe burn.
6. Someone should be within range of your voice, or close enough to
come to your aid when you work near batteries.
This battery is self-contained and not consumer replaceable.
Battery must be disposed of properly when it no longer holds a
charge. Proper charging practices will increase the life of the
Battery Status Indicator LEDs
Jumper cable with clamps
Jump Starter Cable Input
Capacity Button
LED Flashlight/Strobe
Light/ S.O.S Light
12V DC Charge Input
USB 5V/2.1 Amp Output
Home adaptor
Car adaptor
Recharging the JumPack:
The CPP 7500 E JumPack can be recharged with the supplied 220 V AC
wall charger connected to an AC home outlet or with the supplied 13.8 V DC
vehicle charger.
When the CPP 7500 E is charging; the LEDs will show the current
battery life. The last LED that is lit will blink to show that the JumPack
is charging. When the JumPack is fully charged the LEDs will turn off
For best battery performance the JumPack should be fully recharged
every 3 months.
7/3/14 12:10 PM
12:18 PM
Check Battery Capacity:
To check the battery capacity of the JumPack press the
Power/Flashlight button on the top of the unit with no device
connected. The blue LEDs will show the remaining battery
Battery Status Indicator LEDs
Charging a 5V USB Device:
Starting a Vehicle:
To charge a 5V USB device, connect the devices’ cable to the JumPack’s
USB output. The JumPACK will turn on, and start charging the device
automatically. The blue LEDs will indicate that the device is charging.
For European Community Users
Cobra Electronics Corporation complies with Directive 2012/19/EU OF
waste electrical and electronic equipment (WEEE).
1. Make sure the JumPack is fully charged.
2. Turn off all the accessories on the vehicle.
3. Disconnect the battery cables from the JumPack.
4. Connect the RED clamp to the POSITIVE post of the battery.
5. Connect the BLACK clamp to the NEGATIVE post of the battery.
6. Connect the battery cables into the JumPack cables port/jack. Be
1 LED on: 10%-40% charge
2 LEDs on: 40%-65% charge
7. Turn the ignition key to start the vehicle for 3 seconds only. If the
engine starts;
3 LEDs on: 65%-85% charge
8. Disconnect the cables from the battery from the JumPack then
from the battery posts.
4 LEDs on: 85%-100% charge
9. Leave the engine running for a few minutes before turning the
ignition off.
Note: When charging a device the number of lit LEDs may decrease
while the JumPack is in use. The battery capacity indicator cannot
before trying to start the vehicle again.
the real battery capacity, disconnect the device being charged and
CPP7500E_MANL_ENG.indd 2
Customer Support
Should there be any problems with this product or further information
needed on its features please visit for support, frequently
asked questions, Declarations of Conformity, and the electronic manual.
For warranty and customer service information please contact the seller.
wait for 1 minute
LED Flashlight:
Press the Power/Flashlight/Battery capacity button for 3 seconds to turn
S.O.S. and Off.
Product Features:
• 7500 mAh Lithium Cobalt rechargeable battery.
• 200 Amp Starting Current/400 Amp Peak Current.
• 5V/2.1 Amp USB Output for rapid charging of portable devices.
• High Intensity work/Strobe/S.O.S LED light.
• Rechargeable by 240 V AC wall adapter or 13.8 V DC car adapter.
Li-Cobalt rechargeable battery: 3.7 V/7500 mAh
5.03” x 2.87” x 0.98”
(128 mm x 73 mm x 25 mm)
10.58 oz. (300 g.)
Recharge time:
3 hours
Starting/Peak Current:
200 Amps/400 Amps
USB Output:
2.1 Amps
Waste Electrical and Electronic Equipment Information
This product has required the extraction and use of natural resources for
its production. It may contain hazardous substances that could impact
health and the environment, if not properly disposed. In order to avoid
the dissemination of those substances in our environment and to
diminish the pressure on the natural resources, we encourage you to use
the appropriate take-back systems for product disposal. Those systems
will reuse or recycle most of the materials of the product you are disposing
in a sound way.
The crossed out wheeled bin symbol informs you that the product
should not be disposed of along with municipal waste and invites you
to use the appropriate separate take-back systems for product disposal.
If you need more information on the collection, reuse and recycling
systems, please contact your local or regional waste administration.
You may also contact your supplier for more information on the
environmental performances of this product.
Trademark Statement
©2014 Cobra Electronics Corporation, 6500 West Cortland Street,
Chicago, Illinois 60707 U.S.A.
Cobra, the snake design is a proprietary trademark of Cobra Electronics
Corporation, USA.
7/3/14 12:10 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF