Advertisement
Advertisement
User’s manual
SynJ SB67158
DECT 6.0 4-line corded/cordless small business system
Congratulations
on your purchase of this AT&T product. Before using this AT&T product, please read the Important safety information on pages 90-91 of this manual.
Please thoroughly read this user’s manual for all the feature operations and troubleshooting information necessary to install and operate your new AT&T product. You can also visit our website at www.telephones.att.com
or call 1 (888) 915-2007 . In Canada, dial 1 (866) 288-4268 .
Model number: SynJ® SB67158
Type: DECT 6.0 4-line corded/cordless small business system
Serial number:
Purchase date:
Place of purchase:
Both the model and serial numbers of your AT&T product can be found on the bottom of the telephone base.
Save your sales receipt and original packaging in case it is necessary to return your telephone for warranty service.
Telephones identified with this logo have reduced noise and interference when used with most T-coil equipped hearing aids and cochlear implants. The TIA-1083
Compliant Logo is a trademark of the Telecommunications Industry Association.
Used under license.
© 2011-2014 Advanced American Telephones. All Rights Reserved. AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to
Advanced American Telephones, San Antonio, TX 78219. Printed in China.
SynJ® is a trademark of Advanced American Telephones.
Parts checklist
Check to make sure the telephone package includes the following items:
User’s manual
SynJ SB67158
DECT 6.0 4-line corded/cordless small business system
SynJ SB67158
User's manual
Quick start guide
SynJ SB67158 DECT 6.0
4-line corded/cordless small business system
SynJ SB67158
Quick start guide
Telephone base
Handset with coiled cord installed
Two telephone line cords
(4-conductor)
Telephone base power adapter
2 Line splitters Audio cable
User’s manual
SynJ SB67158
DECT 6.0 4-line corded/cordless small business system
Table of contents
Getting started
Quick reference guide .............................. 1
Installation ...................................................... 4
Planning your system ................................ 5
Telephone base installation ................... 6
To connect the corded handset and power adapter to the telephone base......................................... 6
To connect the telephone line cords to the telephone base ............. 7
Optional backup battery installation ... 9
Expand your telephone system ..........10
Add and register handsets ...................10
To register a cordless handset to your telephone base............................10
Add and register desksets ....................11
To register a deskset to your telephone base.......................................11
Add and register a cordless headset .......................................................12
To register a cordless headset to your telephone base............................12
Deregister devices ....................................13
Add a corded headset ............................14
To add a corded headset to the telephone base.......................................14
Telephone base setup .............................15
Menu settings ..........................................15
Ringer volume .........................................15
Volume control .......................................16
Ringer tone ...............................................16
Ring group ................................................17
Do not disturb (DND) ...........................17
Restricted prefix .....................................18
LCD contrast ............................................19
Key tone .....................................................19
Language ...................................................19
Line selection ..........................................20
Set line mode ..........................................20
Area codes ................................................21
Hold reminder .........................................22
Set date and time .................................22
Music on hold (M.O.H.) ........................23
Call alert tone .........................................28
Auto attendant setup (for answering system) ................................29
Record announcement
(auto attendant) .....................................29
Record extension list ...........................30
Number of rings (auto attendant) ... 31
Mailbox setup (for answering system) .......................................................32
Number of rings (general mailbox)......................................................32
Number of rings (announce only) ... 32
Record announcement
(independent mailbox) ........................33
Select announcement .........................33
Mailbox setup (for general mailbox) ...34
Set access code (remote code) ......34
Call screening..........................................34
Persistent hold ........................................35
Notify alert ................................................36
Voice language .......................................37
Remaining space ....................................38
Mailbox setup
(for handset/deskset)..........................39
Fast answer mode .................................39
Handset/deskset announcement setup ............................................................39
Switch to general mailbox ................40
Speed dial setup ........................................41
Enter, edit or delete a speed dial number .......................................................41
Customer support .................................41
Screen icons, indicator tones and lights ..................................................42
COVM ...............................................................53
COVM (central office voicemail) .....53
COVM reset ...............................................53
Intercom .........................................................54
Make an intercom call to a cordless handset/deskset ...............54
Answer an intercom call ....................55
End an intercom call ............................55
Make another intercom call while on an intercom call ..............................55
Answer an incoming call during an intercom call .....................................55
Call transfer .................................................56
Blind transfer ...........................................56
Transfer a call and speak to the receiving party ........................................56
Answer a transferred call ..................57
Push to talk (PTT) intercom .................58
PTT to a single device .........................58
PTT to all devices ..................................58
Answer a PTT call ..................................59
Convert a PTT call to an intercom call ................................................................59
End a PTT call ........................................59
Telephone base operation
Telephone base basic operation ........44
Line indicators .........................................44
Making a call............................................44
On hook dialing (predialing) ............45
Using the speakerphone ....................45
Calling a speed dial number ............45
Answering a call ....................................46
Temporary ringer silencing ...............46
Last number redialing .........................46
Options while on calls ............................47
Volume control .......................................47
Call waiting ...............................................47
Call privacy ...............................................48
Recording a call .....................................49
Mute .............................................................50
Hold ..............................................................50
Switching between lines ....................50
Join a call in progress .........................51
Chain dialing ............................................51
Three-way conference calls .............51
Directory
About the directory ..................................60
Capacity .....................................................60
Exit the directory ...................................60
Create directory entries .........................61
Create a new directory entry ..........61
Store a pause in a directory number .......................................................62
Store a flash in a directory number .......................................................62
Review directory ........................................63
Review directory entries ....................63
Search directory .........................................64
Search by name .....................................64
Dial, delete or edit entries ....................65
Display dial ...............................................65
Delete an entry.......................................65
Delete all entries ...................................65
Edit an entry ............................................65
Caller ID
About caller ID ...........................................66
Information about caller ID with call waiting ...............................................66
Caller ID Information ...............................67
How the caller ID information
(call log) works .......................................67
Caller ID operation ...................................68
Memory match ........................................68
Missed (new) calls indicator .............68
Review the caller ID information ...68
View dialing options .............................69
Dial a call log entry ..............................69
Delete entries ..........................................69
Save a call log entry to the directory .....................................................70
Reasons for missing caller ID information ...............................................71
Incoming messages ..............................78
New message indication ....................78
Message playback .................................78
Options during playback ....................79
Delete all old messages .....................79
Transfer message ..................................80
Record and deliver memos ...............81
Play back a memo ................................82
Set answering system to play announcement only .............................82
Set general delivery mailbox to not answer ................................................82
Disable the answering system ........82
Remote access ............................................83
Cordless headset
Cordless headset operation .................85
Cordless headset extension number .......................................................85
Switch between corded or cordless handset, telephone speakerphone and cordless headset .......................................................85
Answering system
Answering system and voicemail ......72
Setting your system to automatically answer calls ...............73
An example of a 2-line answering system setup ....................73
An example of a 4-line answering system setup ....................74
Select the answer mode ....................74
Answering system capacity ..............74
Auto attendant operation .....................75
Turn the auto attendant on ..............75
Using the auto attendant ..................75
Using multiple auto attendants ......76
Auto attendant flow chart ................77
Answering system operation ...............78
Set general delivery mailbox to answer ........................................................78
Appendix
Telephone base display screen messages ...................................................86
Maintenance.................................................89
Important safety information ..............90
For C-UL compliance ...............................92
Mesures de sécurité importantes ... 92
FCC part 68 and ACTA ............................94
FCC part 15 ..................................................95
Limited warranty ........................................96
Technical specifications .........................98
Troubleshooting .........................................99
Index
Index .............................................................106
Getting started
Quick reference guide
LINE 1-LINE 4 keys
Press to make or answer a call on the desired line (pages 44-46).
ANSWER ON keys
Press to show the automatic answer options for that line
(page 74).
EXIT
While in a menu, press to cancel an operation and exit the menu display.
NEW CALL indicator
On when there are new or missed calls (page 68).
MENU/ENTER
Press to enter the menu.
While in the menu, press to select an item or save an entry or setting.
(Messages)
When in idle mode, press to enter the general mailbox menu (page 78).
CONF
Press to add another extension or outside line to an existing call (pages
51-52).
HOLD
Press to place an outside call on hold (page 50).
Navigation keys
While in menus, press or to scroll through the menus, highlight items or change settings. Press REP to return to the previous menu.
While entering names or numbers, press REP or SKIP to move the cursor to the left or right.
While playing back messages, press REP once to repeat the message, or press REP twice to hear the previous message, or press SKIP to skip to the next message.
1
Getting started
Quick reference guide
CALL LOG
Press to view caller ID information (page 68).
PAUSE/REDIAL
Press repeatedly to view the last 10 numbers dialed
(page 46).
While entering digits, press to insert a dialing pause
(page 62).
DIR
Press to view directory information (page 63).
REMOVE
While playing a message, press to delete the message (page 79).
While reviewing the caller ID information, directory entry, or last redial number, press to delete an individual entry (page 69, page
65 and page 46, respectively).
While predialing, press to delete digits (page 46).
Press to page all extensions. An intercom connection is established with the first extension that answers (page 54).
Press and hold to broadcast your voice to all extensions (page 58).
One-touch keys, EXT 1-0
Press to intercom with the desired cordless extension number (page 54).
Press and hold to broadcast your voice to that extension (page 58).
Directory card
To write names on the directory card, follow the steps mentioned below:
1. Remove the clear plastic cover by inserting the tip of a small item, such as a paper clip, into the hole at the top edge of the cover.
2. Pull out the directory card.
3. Write the information on the directory card.
4. Replace the directory card and the plastic cover.
2
Getting started
Quick reference guide
HEADSET
When a corded headset is connected to the telephone base, press to get a line, answer a call or hang up (pages 41-42).
The red indicator is on when the headset is in use.
INT
When in idle mode, press to initiate an intercom call (page 54).
MUTE
During a call, press to mute the microphone
(page 50). During an incoming call, press to mute the ringer
(page 46).
DND
(do not disturb)
Press twice to turn the feature on. Press again to turn off (page 17).
SPEAKER
Press to turn on the speakerphone. Press again to turn it off (page 45).
FLASH
During a call, press to answer an incoming call when you receive a call waiting alert (page 47).
XFER (transfer)
Press to transfer a call to an extension (page 56).
Press to transfer messages from the general mailbox to a handset mailbox (page 80).
VOL+/VOL-
During a call, press to adjust the listening volume (page 16).
During message playback, press to adjust the playback volume (page 79).
Main menu
The > symbol highlights a menu item.
> Directory
Call log
Ringer setting
RestrictedPrefix
Menu
•
•
•
•
•
•
•
•
•
•
Main menu
Directory (pages 60-65)
Call log (pages 62-70)
Ringer setting (pages 15-17)
RestrictedPrefix (page 18)
Mailbox setup (pages 32-37)
Base setup (pages 19-27)
COVM (page 53)
Speed dial setup (page 41)
Customer support (page 41)
Registration (pages 10-13)
Using menus
•
•
Press MENU/ ENTER to show the first menu item, Directory .
Press or to scroll through menu items.
•
•
•
Press MENU /ENTER to select or save changes to a highlighted menu item.
Press EXIT to cancel an operation, exit the menu display or return to the idle screen.
Press REP to back up to the previous menu.
3
Getting started
Installation
Install the telephone base close to a telephone jack and a power outlet not controlled by a wall switch. The telephone base should be placed on a flat surface. For optimum range and better reception, place the telephone base in a central and open location.
If you subscribe to high-speed Internet service (DSL - digital subscriber line) through your telephone lines, you must install a DSL filter between each telephone line cord and telephone wall jack (page 7). The filter prevents noise and caller ID problems caused by DSL interference. Please contact your DSL service provider for more information about DSL filters.
Your product may be shipped with a protective sticker covering the telephone base and handset displays - remove them before use.
For customer service or product information, visit our website at www.telephones.att.com
or call 1 (888) 915-2007 . In Canada, dial
1 (866) 288-4268 .
•
•
•
•
•
•
Avoid placing the telephone base too close to:
• Communication devices such as television sets, VCRs, or other cordless telephones.
Excessive heat sources.
Noise sources such as a window with traffic outside, motors, microwave ovens, refrigerators, or fluorescent lighting.
Excessive dust sources such as a workshop or garage.
Excessive moisture.
Extremely low temperature.
Mechanical vibration or shock such as on top of a washing machine or work bench.
4
Getting started
Planning your system
The SynJ SB67158 system supports a maximum of four external lines, which are provided by your telephone service provider.
You can expand the system by adding a combination of up to 10 additional cordless handsets (AT&T model SynJ SB67108), desksets (AT&T model SynJ
SB67148), and one cordless headset (AT&T model TL7600). The system automatically assigns an extension number to each device you add.
You can use a DECT 6.0 repeater (AT&T model SynJ SB67128) to extend the operating range for cordless handsets to cover areas where the signal is very weak or not available.
NOTES:
•
•
•
If you have two or three telephone lines, you will need one two-line adapter for every two lines. If you have four telephone lines, you will need two two-line adapters.
If your establishment has four telephone lines from one-line telephone jacks, you will need to purchase a telephone line cord (purchased at an electronics store in your area) or equivalent for each two-line adapter.
If you have high-speed Internet service (DSL - digital subscriber line), you need to have an external or internal DSL splitter for each telephone line installed at your location by your DSL provider.
IMPORTANT INFORMATION
•
•
•
•
•
For complete instructions on using accessory cordless handsets or headsets, please refer to the appropriate manual.
Purchase any desired accessories:
Cordless handsets (AT&T model SynJ SB67108)
DECT 6.0 expansion desksets (AT&T model SynJ SB67148)
Cordless headsets (AT&T model TL7600)
DECT 6.0 repeaters (AT&T model SynJ SB67128)
Additional telephone line cords
To order these accessories or to view the manuals, visit our website at www.telephones.att.com
, or call 1 (888) 915-2007 .
In Canada, dial
1 (866) 288-4268 .
5
Getting started
Telephone base installation
To connect the corded handset and power adapter to the telephone base
Plug the large end of the power adapter into a power outlet not controlled by a wall switch.
Raise the two antennas for optimum wireless range and performance. For greater range, add optional repeaters
(AT&T model SynJ SB67128).
Plug the end of the coiled handset cord into the
HANDSET jack on the left side of the telephone.
Plug the small end of the power adapter into the power jack at the bottom of the telephone base. Route the power adapter cord through the slot on the bottom of the telephone.
NOTE: For complete instructions on installing the cordless handset, see Add and register handsets on page 10 of this user’s manual, or refer to the SynJ SB67108 user’s manual. For complete instructions on installing the expansion deskset, see Add and register desksets on page 11 of this user’s manual, or refer to the SynJ SB67148 user’s manual. You can visit www.telephones.att.com/smb
to download the user’s manuals.
IMPORTANT INFORMATION
1.
2.
Use only the power adapter supplied with this product. To order a replacement power adapter, visit our website at www.telephones.att.com
, or call
1 (888) 915-2007
.
In Canada, dial
1 (866) 288-4268
.
The power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.
6
Getting started
Telephone base installation
To connect the telephone line cords to the telephone base
If you subscribe to high-speed Internet service (DSL - digital subscriber line) through your telephone lines, you must install a DSL filter between each telephone line cord and telephone wall jack. The filter prevents noise and caller ID problems caused by DSL interference. Please contact your DSL service provider for more information about DSL filters.
Install the telephone line cords, as shown below:
Line 3 + Line 4 Line 1 + Line 2
Electrical outlet not controlled by a wall switch
Telephone line cords
Power adapter If you have DSL high-speed Internet service, a DSL filter
(not included) is required on each
DSL line.
Option 1: To connect two 2-line wall jacks
7
Getting started
Telephone base installation
Electrical outlet not controlled by a wall switch
Line 4 Line 3 Line 2
Two-line adapters
Line 1
Power adapter
If you have DSL high-speed Internet service, a DSL filter
(not included) is required on each
DSL line.
Option 2: To connect four one-line wall jacks
1.
2.
NOTES:
If you have three one-line wall jacks, you need a two-line adapter for two of the lines.
The long cords supplied with the telephone are four-conductor cords.
8
Getting started
Optional backup battery installation
In the event of a power failure, if four AA batteries (purchased separately) are installed in the telephone, your telephone base can still operate. All lines will work.
If power fails during a call on the telephone base, the call continues until you hang up. If power fails during a call on a handset, you can still make and answer calls. During a power failure, although the screen backlight is off, you can still make and answer calls. If the power resumes while you are on a call, the call continues.
Install the batteries, as shown below:
Step 1 Open the backup battery compartment cover.
Step 2 Place the batteries in the compartment following the polarity label + / .
Step 3 Align the cover flat against the battery compartment, then slide it to the left until it clicks into place to lock the cover.
1.
2.
NOTES:
Use disposable AA alkaline batteries only. Do not use rechargeable batteries.
When the backup battery is in low battery mode, the screen displays Low battery .
9
Getting started
Expand your telephone system
Your telephone can support a maximum of 10 handsets/desksets, or 9 handsets/ desksets and one cordless headset. You can add handsets, desksets, and one headset (AT&T models SynJ SB67108, SynJ SB67148 and TL7600, sold separately) to the SynJ SB67158 at any time, but each new handset/deskset or headset must be registered to the telephone base before use. You must register each handset, deskset and headset separately.
Add and register handsets
Additional handsets are assigned numbers in the order they are registered
( Handset 1 to Handset 10 ).
If the handset does not have enough power to proceed with the registration, you need to charge the new handset for at least five minutes (see Battery installation and charging in the SynJ SB67108 cordless handset manual). Start registration when the handset screen shows Press MENU on BS, sel
Registration & sel Register HS. Then put HS in cradle.
Press MENU on BS, sel Registration
& sel Register
HS. Then put HS in cradle.
To register a cordless handset to your telephone base
1. Make sure the handset is out of the charger and the screen shows Press MENU on BS, sel Registration & sel Register HS. Then put HS in cradle. before you begin registration.
2. On the telephone base, press MENU /ENTER.
3. Scroll down to Registration and press MENU/ ENTER .
4. Press MENU/ ENTER again to select Register HS . The telephone base screen shows Registering new device...
5. Place the unregistered handset into the charger. The handset beeps once and begins registering to the telephone base. It takes up to 60 seconds to complete the registration. There is a beep sound when the registration is successful. The telephone base shows
Handset registered and then the handset shows
X:Handset X ( X represents the handset number [ 1 0 ];
Handset X represents the handset name).
SB67158:
COVM
Speed dial setup
Customer support
> Registration
> Register HS
Deregistration
Registering new device...
Handset registered
1.
2.
NOTES:
If the registration is not successful, the telephone base screen displays
Registration failed with an error tone. To reset the handset, remove the handset from the cradle. Try the registration process again.
Make sure to remove all unregistered system handsets or cordless headset from the cradles before registering a new handset.
10
SB67108:
2:Handset 2
Set date & time
Charging
Getting started
Add and register desksets
Additional desksets are assigned numbers in the order they are registered
( Deskset 1 to Deskset 10 ).
Start registration when the deskset screen shows Press
MENU on MAIN base, select Registration & then Register
HS. Then press Start.
Press MENU on
MAIN base, select
Registration & then Register HS.
Then press Start
To register a deskset to your telephone base
1. The SynJ SB67148 deskset shows Press MENU on Main base, select Registration & then Register HS. Then press
Start. before you begin registration.
2. On the main telephone base, press MENU /ENTER.
3. Scroll down to Registration and press MENU/ ENTER .
4. Press MENU/ ENTER again to select Register HS .
5. Press the Start softkey on the unregistered deskset. The telephone base screen shows Registering new device...
It takes up to 60 seconds to complete the registration.
You hear a beep when the registration is successful.
The telephone base shows Deskset registered and the deskset shows X:Deskset X ( X represents the extension number [ 1 0 ]; Deskset X represents the deskset name).
SB67158:
COVM
Speed dial setup
Customer support
>
Registration
>
Registration
Deregistration
Registering new device...
Deskset registered
NOTE: If the registration is not successful, the telephone base screen displays Registration failed with an error tone. Try the registration process again.
SB67148:
2:Deskset 2
Set date & time
Redial Menu
11
Getting started
Add and register a cordless headset
You can use this phone handsfree when you register a DECT
6.0 cordless headset (AT&T model TL7600, sold separately) to the telephone base. You can only register one cordless headset to the telephone base. The cordless headset must have a charged battery. Make sure the headset battery is properly installed.
Place the headset in the headset charger and note the color of the ON/OFF button. If the button flashes a blue and orange light twice every five seconds, the headset is unregistered. If the button shows a constant blue light, the headset is registered. You need to deregister the headset before you can register it to the SynJ SB67158. See the deregistration instructions in the user’s manual of the telephone to which it is currently registered. See page 85 for instructions on using the cordless headset with this telephone.
To register a cordless headset to your telephone base
1.
Place the headset in the headset charger and allow it to charge for at least five minutes before beginning registration. Make sure the headset is out of the headset charger before you begin registration.
2.
On the telephone base, press MENU /ENTER .
3.
Scroll down to Registration and press MENU/ ENTER .
4.
Press MENU/ ENTER again to select Register HS . The telephone base shows Registering new device...
It takes up to 60 seconds to complete the registration.
5.
Place the headset into the cradle. The telephone base shows Cordless headset registered and beeps when the registration is successful.
6.
Lift the headset, then press the headset ON /OFF button.
If you hear a dial tone and the extension
0
icon appears on the telephone base, the registration was successful.
If there is no dial tone, or the ON/OFF light on the headset flashes twice every five seconds, the registration was not successful. Remove the headset from the headset charger and repeat the registration process again, starting with Step 2, as mentioned above.
If you have a dial tone but an extension number other than
0 displays on the telephone base, the headset is registered as a handset and will not function properly. If this is the case, you must deregister and start over. See Deregister devices on the next page.
12
COVM
Speed dial setup
>
Customer support
Registration
> Register HS
Deregistration
Registering new device...
Cordless headset registered
Line1
0
00:00:05
Getting started
Deregister devices
If you already have 10 registered devices and need to replace or add a new device, or if you wish to change the assigned extension numbers of your devices, you must first deregister the desired device(s) first, then register the device(s) you wish to use, one at a time. Deregistering a cordless handset or deskset does not remove the data saved on that device. Please read all the instructions on this page before beginning the deregistration process.
Please make sure the telephone system is not in use before deregistration.
To deregister a single device or all devices registered to the telephone base:
1. On the telephone base, press
2. Scroll down to Registration
MENU /ENTER and press
.
MENU/ ENTER .
COVM
Speed dial setup
Customer support
> Registration
3. Scroll down to Deregistration and press MENU/ ENTER .
4. The telephone base screen shows Deregister: .
• If you want to deregister a single device, scroll to choose the desired device, then press MENU/ ENTER .
• If you want to deregister all devices, scroll to choose
All , then press MENU/ ENTER .
5. For deregistration of a single device, the telephone base screen prompts if you want to deregister that device. If you selected all devices, it shows Deregister All?
<=No >=Yes .
Press REP to exit or press SKIP to continue the deregistration.
Register HS
> Deregistration
Deregister:
Handset 1
Deskset 2
>All
6. If you press SKIP , the telephone base shows
Deregistering . It takes up to 10 seconds to complete the deregistration. When the deregistration is successful, there is a confirmation tone and the telephone base shows the deregistration completion message.
Deregister
All?
<=No >=Yes
Deregistering
All devices deregistered
1.
2.
3.
4.
NOTES:
If the deregistration process is not successful, you might need to reset the system and try again.
To reset, you can press EXIT on the telephone base. You can also reset the telephone base by unplugging the power from the telephone base and plugging it back in.
To register a cordless handset again, refer to the registration information on page 10.
To register an expansion deskset again, refer to the registration information on page 11.
To register a cordless headset again, refer to the registration information on page 12.
13
Getting started
Add a corded headset
You can use this telephone handsfree when you install any industry-standard
2.5mm corded telephone headset (purchased separately). For best results, use an AT&T 2.5mm corded headset. To purchase a headset, visit our website at www.telephones.att.com
, or call 1 (888) 915-2007 . In Canada, dial 1 (866) 288-4268 . See page 45 for instructions on using the corded headset with this telephone.
To add a corded headset to the telephone base
Plug a 2.5 mm headset into the HEADSET/AUX IN jack on the side of the telephone base.
Side view of the telephone base
NOTE: If you have corded and cordless headsets connected to your telephone base, the
HEADSET button only controls the corded headset.
14
Getting started
Telephone base setup
Menu settings
3.
4.
Use this feature to use the menus to change the telephone base settings.
1.
Press MENU /ENTER when in idle mode (when the telephone is not in use) to enter the main menu.
2.
The > symbol indicates the selected menu item.
Press MENU/ ENTER to select the menu item.
Press EXIT to exit setup without making changes.
NOTE: Press EXIT to cancel an operation, exit the menu display, or return to idle mode.
Ringer volume
Use this feature to set the ringer volume to one of three levels or turn the ringer off. When the ringer is off, the icon appears on the telephone base screen.
1. When the telephone is idle, press MENU /ENTER .
2. Press or to scroll to Ringer setting . Press MENU/ ENTER .
3. Press MENU/ ENTER again to select Ringer volume .
4. Press , , VOL+ or VOL- on the telephone base to adjust the ringer volume.
5. Press MENU/ ENTER to save the setting and return to the previous menu. There is a confirmation tone. To exit without making changes, press EXIT .
Directory
>
Call log
Ringer setting
RestrictedPrefix
> Ringer volume
Ringer tone
Ringer group
Ringer volume
ENTER=Save
NOTE: The ringer volume also determines the ringer volume for intercom calls (page 54). If the telephone base ringer volume is set to off, that telephone base is silenced for all incoming calls, including intercom calls.
Ringer volume
ENTER=Save
*: Base
0 missed calls
5:12PM 4/27
15
Getting started
Telephone base setup
Volume control
Use this feature to independently set the listening volume to one of five levels for each of the three listening options
(corded handset, speakerphone and corded headset). While using each, press , , VOL+ or VOL to adjust the listening volume.
Volume
While adjusting the volume on the corded handset or the corded headset, you hear a triple beep when you reach the minimum or maximum volume setting.
The SynJ SB67158 telephone base stores the volume setting for each listening option.
Ringer tone
Use this feature to choose one of the seven ringer tones for incoming calls.
You can choose different ringer tones for different lines so you can easily identify which line is ringing.
1.
When the telephone is idle, press MENU /ENTER .
2.
Press or to scroll to Ringer setting . Press MENU/ ENTER .
Directory
Call log
> Ringer setting
RestrictedPrefix 3.
Press or to scroll to Ringer tone . Press MENU/ ENTER .
4.
Press REP or SKIP to select the desired line ( L1 , L2 ,
L3 or L4 ).
5.
Press or to select a desired ringer tone.
Ringer volume
> Ringer tone
Ringer group
6.
Repeat steps 4-5 to choose ringer tones for other lines, if desired.
7.
Press MENU/ ENTER to save the setting and return to the previous menu. There is a confirmation tone. To exit without making changes, press EXIT .
Ringer tone
L1 L2 L3 L4
1 1 1 1
Ringer tone
L1 L2 L3 L4
1 3 1 1
NOTE: If you turn off the ringer volume, you will not hear ringer tone samples.
16
Getting started
Telephone base setup
Ring group
Use this feature to specify which extensions receive incoming calls. By default, all extensions and the telephone base receive incoming calls. You can block some extensions from receiving calls, however, they can still be used to make outgoing calls.
1.
When the telephone is idle, press MENU /ENTER .
2.
Press or to scroll to Ringer setting . Press
MENU/ ENTER .
3.
Press or to scroll to Ring group . Press MENU/
ENTER .
4.
Press REP or SKIP to select a desired line ( L1 , L2 , L3 or L4 ) while Ring group flashes.
Directory
Call log
> Ringer setting
RestrictedPrefix
Ringer volume
Ringer tone
> Ring group
5.
Press or to scroll to Extension number: . Use the dial pad to press the number of the extension
( * , 1 , 2 , 3 , 4 , 5 , 6 , 7 , 8 , 9 , 0 ) that you want to delete, or press the number again to add it back to the ring group.
6.
Press MENU/ ENTER to save the setting and return to the previous menu. There is a confirmation tone. To exit without making changes, press EXIT .
Ring group: L3
Extension number:
*1234567890
<>
Ring group: L3
Extension number:
*1-3-56-8-0
ENTER =Save
NOTE: The symbol
*
represents the telephone base; 0 represents extension 10.
Do not disturb (DND)
Use this feature to silence your telephone base. When you activate the do not disturb function, the icon appears on the telephone base screen and you will not hear paging tones, voice paging or incoming call rings.
Instead, the LINE 1 LINE 4 indicator flashes to signal an incoming call. If you receive an intercom call, the extension number of that intercom call appears on the screen display.
1.
Press DND twice to prevent interruptions. The DND indicator turns on.
2.
Press DND again to resume normal call alerts. The DND indicator turns off.
*: Base
0 missed calls
5:12PM 4/27
17
Getting started
Telephone base setup
Restricted prefix
This feature allows you to restrict certain extensions from dialing telephone numbers starting with the user-defined prefix (from one to three digits).
If you attempt to dial out with the restricted prefix using an extension in the restricted list, there is an alert sound and Call restricted displays on the screen. After about five seconds, the device returns to idle mode.
Call restricted
Set restricted prefix:
1.
When the telephone is idle, press MENU /ENTER .
2.
Press or to scroll to RestrictedPrefix , then press
MENU /ENTER .
3.
Press MENU/ ENTER again to select Set prefix .
4.
Enter the restricted prefix (up to three digits) using the dial pad when prompted.
•
•
•
Press REP or SKIP to move the cursor to the left or right.
Press REMOVE to backspace and delete a digit.
Press and hold REMOVE to erase all digits.
5. Press MENU/ ENTER to save the setting. The screen displays the restricted prefix briefly and then returns to the previous menu. There is a confirmation tone. To exit, press EXIT .
Directory
Call log
Ringer setting
> RestrictedPrefix
> Set prefix
Restricted Ext
Enter prefix:
015
ENTER=Save
RestrictedPrefix:
015
Set restricted extension:
1.
When the telephone is idle, press MENU /ENTER .
Set prefix
> Restricted Ext
2.
Press or to scroll to RestrictedPrefix , then press
MENU /ENTER .
3.
4.
Press or to scroll to Restricted Ext , then press
MENU /ENTER .
Restricted Ext:
- 1 - 3 - - - - - - -
ENTER=Save
Use the dial pad to press the number of the extension
( * , 1 , 2 , 3 , 4 , 5 , 6 , 7 , 8 , 9 , 0 ) that you want to restrict, or press the number again to remove it from the list.
5.
Press MENU/ ENTER to save the setting and return to the previous menu.
There is a confirmation tone. To exit, press EXIT .
18
Getting started
Telephone base setup
LCD contrast
Use this feature to adjust the screen contrast to one of six levels to optimize readability in different lighting conditions.
1.
2.
When the telephone is idle, press
Press or to scroll to
MENU
Base setup
/ENTER
, press
.
MENU /ENTER .
Ringer setting
RestrictedPrefix
Mailbox setup
> Base setup
3.
Press MENU/ ENTER again to select LCD contrast .
4.
Press or to adjust the screen contrast level. The screen display temporarily fades away as you press and reappears as you press .
> LCD contrast
Key tone
Language
Line selection
LCD contrast
5.
Press MENU/ ENTER to save the setting and return to the previous menu. There is a confirmation tone. To exit, press EXIT .
ENTER=Save
Key tone
Use this feature to turn the key tone on and off. The telephone base is factory set to beep with each key press. You can turn off this beep sound by turning the key tone off.
1.
2.
3.
When the telephone is idle, press MENU /ENTER .
Press or to scroll to Base setup . Press MENU/ ENTER .
Press or to scroll to Key tone . Press MENU/ ENTER .
LCD contrast
> Key tone
Language
Line selection
4.
Press or to scroll to On or Off .
5.
Press MENU/ ENTER to save the setting and return to the previous menu. There is a confirmation tone. To exit without making changes, press EXIT .
Key tone
:Off
ENTER=Save
Language
Use this feature to change the display language that is used in all menus and screen displays. Set the display language on the telephone base and each extension separately. This telephone comes factory set for English displays.
1.
When the telephone is idle, press MENU /ENTER .
2.
3.
Press or to scroll to
Press or to scroll to
Base setup
Language
. Press
. Press
MENU/
MENU/
ENTER
ENTER .
.
LCD contrast
Key tone
> Language
Line selection
4.
Press or to select English , Español or Français .
5.
Press MENU/ ENTER again to save the setting and return to the previous menu. There is a confirmation tone.
To exit without making changes, press EXIT .
19
Language
:English
ENTER=Save
Getting started
Telephone base setup
Line selection
Use this feature to select the default telephone line to be used when you make outgoing calls. This telephone comes factory set for Auto selectable line, which chooses the first available line for making a call. To select a particular line, choose Line 1 , Line 2 , Line 3 or Line 4 .
1.
2.
3.
4.
When the telephone is idle, press MENU /ENTER .
Press or to scroll to Base setup . Press MENU/ ENTER .
Ringer setting
RestrictedPrefix
Mailbox setup
> Base setup
Press or to scroll to Line selection . Press MENU/ ENTER .
Press or to select or Line 4 .
Auto , Line 1 , Line 2 , Line 3
LCD contrast
Key tone
Language
> Line selection
5.
Press MENU/ ENTER to save the setting and return to the previous menu. There is a confirmation tone. To exit without making changes, press EXIT .
Line selection
:Auto
ENTER=Save
Set line mode
Use this feature to individually select the line mode for each available telephone line. For the system to behave properly, it needs to be set for: a) PBX lines, which are typical business telephone systems that require you to dial 8 or 9 to get an outside line.
-ORb) CO lines, which are standard residential telephone lines.
This telephone comes factory set for PBX lines.
1.
When the telephone is idle, press MENU /ENTER .
2.
Press or to scroll to Base setup . Press MENU/ ENTER .
3.
Press or to scroll to Set line mode . Press MENU/ ENTER .
4.
Press or to scroll to a desired line ( L1 , L2 , L3 or L4 ).
5.
Press REP or SKIP to select PBX or CO .
6.
Repeat Steps 4 and 5 to choose the line mode for other lines, if desired.
Language
Line selection
Area codes
> Set line mode
L1
L2
L3
L4
CO
PBX
CO
PBX
7.
Press MENU/ ENTER to save the setting and return to the previous menu.
There is a confirmation tone. To exit without making changes, press EXIT .
20
Getting started
Telephone base setup
Area codes
Use this feature to program this system to recognize one home area code and up to four local area codes. This feature makes it easy for you to place a call from the caller ID log.
If you dial seven digits to make a local call (no area code required), enter your area code into the telephone as the home area code. When you receive a call from within your home area code, the caller ID information only displays the seven digits of the telephone number, and when you dial from the call log, only seven digits are dialed.
If you must dial 10 digits (the area code and telephone number) for local calls, enter 000 for the home area code and enter your area code as a local area code. Then, if you receive a call from within your area code, the screen displays all 10 digits of the telephone number, and when you dial from the call log, all 10 digits are dialed.
If you have more than one area code for your region, enter those area codes as local area codes.
1.
When the telephone is idle, press MENU /ENTER .
2.
3.
Press or to scroll to
Press or to scroll to
Base setup
Area codes
. Press
. Press
MENU/
MENU/
ENTER
ENTER .
.
Ringer setting
RestrictedPrefix
Mailbox setup
> Base setup
4.
5.
6.
Press or to scroll to
Local area 4 . Press MENU/
Home area
ENTER
or Local area 1
to edit it.
- Language
Line selection
> Area codes
Set line mode
Use the dial pad keys to enter a three-digit area code.
Enter 000 for your home area code if you always dial ten-digit numbers. Press REP or SKIP to scroll to the digit you want to edit, or press REMOVE once to delete a digit; press and hold REMOVE to delete all digits.
>
Home area
Local area 1
Local area 2
Local area 3
Enter code:
000
Press MENU/ ENTER to save the setting and return to the previous menu. There is a confirmation tone. To exit without making changes, press EXIT .
ENTER=Save
Home area:
000
21
Getting started
Telephone base setup
Hold reminder
When there is a call on hold for more than three minutes, the telephone base gives you a triple beep every 30 seconds. You can set its volume to one of the three levels or turn the hold reminder off.
1.
When the telephone is idle, press MENU /ENTER .
2.
3.
4.
5.
Press or to scroll to Base setup . Press MENU/ ENTER .
Press or to scroll to Hold reminder . Press MENU/ ENTER .
Press or , VOL+ or VOL to adjust the volume or turn the setting off.
Press MENU/ ENTER to save the setting and return to the previous menu. There is a confirmation tone. To exit without making changes, press EXIT .
Line selection
Area codes
Set line mode
>
Hold reminder
Hold reminder
Flashing
ENTER=Save
Set date and time
The answering system displays the date and time of the message while playing messages. Before using the answering system, set the date and time as follows. If you subscribe to caller ID service, the day, month and time are set automatically with each incoming call. The year must be set so that the day of the week can be calculated from the caller ID information.
Follow the steps to set the month, day, year and time:
1.
2.
3.
When the telephone is idle, press MENU /ENTER .
Press or to scroll to Base setup . Press MENU/ ENTER .
Press or to scroll to Date and time . Press MENU/ ENTER .
Area codes
Set line mode
Hold reminder
>
Date and time
4.
5.
6.
Using the dial pad to enter the date. Press REP or SKIP to scroll to the item you want to edit, and press the dial pad keys to enter the correct digit.
Date: 1 2.31. 2006
Time: 09:00 AM
^v=PM
ENTER=Save
7.
Press to move to the time editing.
Press or to select AM or PM .
Press REP or SKIP to scroll to the item you want to edit, and press the dial pad to enter the correct digit.
Date: 01.01. 2009
Time: 12:00 PM
^v=AM
ENTER=Save
8. Press MENU/ ENTER to save the setting and return to the previous menu. There is a confirmation tone. To exit without making changes, press EXIT .
1.
NOTES:
The time is in a 12-hour clock format. If you set an invalid time, you will hear an error tone while pressing MENU/ ENTER to save the setting. The error tone means the setting cannot be saved. You need to correct the time entry to continue the setup process.
2.
If the date and time are not set when a message is recorded, the system does not display date and time on the screen while playing messages.
22
Getting started
Telephone base setup
Music on hold (M.O.H.)
You can choose what callers hear when placed on hold. M.O.H. is set to on by default.
You have four options:
• If you want callers you place on hold to hear nothing, turn M.O.H. off.
•
•
•
If you want callers on hold to hear the default music that comes with the telephone, turn M.O.H. on but do not record your own music or voice message.
If you want callers on hold to hear audio that you record onto the telephone, see the instructions on pages 25-26.
If you want callers to hear audio directly streamed into the telephone, connect an audio source such as a computer, MP3 player or radio to the telephone base (page 27).
Turn M.O.H. on or off:
1.
2.
When the telephone is idle, press
Press or to scroll to
MENU
Base setup
/ENTER
. Press
.
MENU/ ENTER .
3.
Press or to scroll to Music on hold . Press MENU/ ENTER .
Ringer setting
RestrictedPrefix
Mailbox setup
>
Base setup
4.
5.
6.
Press MENU/ ENTER again to select
Press or to highlight On or
M.O.H. on/off
Off .
.
Area codes
Hold reminder
>
Date and time
Music on hold
If you select On and the source is Recorded M.O.H.
, when you press MENU/ ENTER to save the setting,
Music on hold: On displays.
-OR-
If you select On and the source is Aux In Device with an audio device connected, when you press MENU/ ENTER to save the setting, Device connected to the headset jack will be used for M.O.H.
displays.
> M.O.H. on/off
Review M.O.H.
Record new M.O.H.
M.O.H. source
Music on hold
:On
ENTER=Save
The screen returns to the previous menu. To exit without making changes, press EXIT .
Device connected to the headset jack will be used for M.O.H.
NOTE: If M.O.H. is turned on, you cannot make any changes to M.O.H. settings while a call is currently on hold. The screen displays M.O.H. currently in use. Please try again later .
No Device is connected to the headset jack at base.
23
Getting started
Telephone base setup
2.
3.
Listen to the music on hold:
1.
When the telephone is idle, press MENU /ENTER .
Press or to scroll to Base setup . Press MENU/ ENTER .
Press or to scroll to Music on hold . Press MENU/ ENTER .
4.
Press or to scroll to Review M.O.H.
Press MENU/ ENTER .
M.O.H. on/off
> Review M.O.H.
Record new M.O.H.
M.O.H. source
> Recorded M.O.H.
Aux In Device
5.
Press or to highlight Recorded M.O.H. or Aux In Device .
If you select Recorded M.O.H.
, press MENU/ ENTER to hear the current recording or the default music.
Play M.O.H.
01:42
-OR-
If you select Aux In Device , press MENU/ ENTER to hear the current music playing on your audio device that is connected to the telephone base.
-OR-
<=Back
Aux In Device playing
<=Back
If you select Aux In Device but there is no audio device connected with the telephone base, No Device is connected to the headset jack at base displays on the screen. Connect an audio device to the HEADSET/AUX IN jack (as shown below), then choose Review M.O.H.
Recorded M.O.H.
>
Aux In Device
6. Press REP to return to the previous menu.
Change the music on hold volume:
No Device is connected to the headset jack at base.
The music on hold volume can only be changed at the audio device.
1.
Place a call to your SynJ SB67158.
2.
Press HOLD on the SynJ SB67158 to place the call on hold. Listen to the music on hold to determine if the volume is desirable.
3.
If you are using recorded audio and want to make adjustments to the volume on the audio device and record the audio again, start again with Step 1 of
Change the music on hold volume .
-OR-
If you get streaming audio from a device and want to make adjustments to the volume, change the volume on the audio device while the call is on hold until you find the desired volume. When you finish listening to the audio, hang up both telephones.
24
Getting started
Telephone base setup
Record music or a voice message
You can record audio or music from an audio source such as a computer, MP3 player, or stereo using the audio cable provided. The recording can be up to three minutes long and plays repeatedly while a call is on hold.
>
M.O.H. on/off
Review M.O.H.
Record new M.O.H.
M.O.H. source
NOTE: It is the user’s responsibility to comply with the copyright laws and to provide lawfully acquired music for the music on hold feature. Unlawful use of copyright protected music and/or lyrics may subject the user to fines and other legal action.
Record music or a message using an audio device:
1.
When the telephone is idle, press MENU /ENTER .
2.
Press or to scroll to Base setup . Press MENU/ ENTER .
3.
Press or to scroll to Music on hold . Press MENU/ ENTER .
4.
Press or to scroll to Record new M.O.H.
Press MENU/ ENTER .
5.
6.
Plug the small end (2.5mm plug) of the audio cable into the HEADSET/AUX IN jack on the telephone base and plug the large end (3.5mm plug) of the audio cable into the audio output jack on your audio device (as shown on the previous page).
M.O.H. record
ENTER=Start
M.O.H. record
When your audio device is ready to play, press MENU/ ENTER on the telephone. You hear the voice prompt “Record after
00:09
ENTER=Stop the tone. Press stop when you are done.” Start playing the sound or message on your audio device after the beep. The audio plays through the speakerphone and a counter on the screen shows the elapsed time. The maximum record time is three minutes, at which time the telephone automatically stops recording and the recording is saved.
7.
Press MENU/ ENTER to stop recording. The screen display returns to the previous menu. To exit without making changes, press EXIT .
25
Getting started
Telephone base setup
Record music or a message using the corded handset:
1.
When the telephone is idle, press MENU /ENTER .
M.O.H. record
2.
Press or to scroll to Base setup . Press MENU/ ENTER .
3.
Press or to scroll to Music on hold . Press
MENU/ ENTER .
ENTER=Start
4.
Press or to scroll to Record new M.O.H.
Press MENU/ ENTER .
M.O.H. record
00:06
ENTER=Stop
5.
When the screen shows M.O.H. record ENTER=Start , pick up the handset.
6.
When your audio device is ready to play, press MENU/ ENTER on the telephone. You hear the voice prompt “Record after the tone. Press stop when you are done.” Start playing your audio device or speak after the beep. The audio plays through the speakerphone and a counter on the screen shows the elapsed time. The maximum record time is three minutes, at which time the telephone automatically stops recording and the recording is saved.
7.
Press MENU/ ENTER to stop recording and return to the previous menu. To exit without making changes, press EXIT .
1.
2.
3.
4.
NOTES:
If you want to record a piece of new music or a message while the music on hold is in use, M.O.H. currently in use. Please try again later.
displays on the screen.
M.O.H. currently in use. Please try again later.
If you start to record a piece of new music from an audio device but there is no audio device connected, No Device is connected to the headset jack at base. displays on the screen. Please check the connection on the telephone base and the audio device.
If there is silence detected for six seconds while recording or your audio device volume is too low, the recording stops and the display automatically returns to the previous menu. This means the recording was unsuccessful. The M.O.H. default music plays when calls are on hold until you successfully record new music or a message.
If you fail to record a message, try speaking louder into the corded handset or playing the volume louder on your audio device. If you are using the audio cable, ensure that it is fully plugged into the
HEADSET/AUX IN jack.
Delete your recording to use the default music:
If M.O.H. is turned on and you do not record your own audio, the default music will play. To delete your recorded audio and go back to using the default music, you must record six seconds of silence.
1. Follow Steps 1-5 of Record music or a message using an audio device on page 25.
26
Getting started
Telephone base setup
2. Unplug any audio device that is connected to the HEADSET/AUX IN jack from the telephone base.
3. Press MENU/ ENTER to start recording. After recording six seconds of silence, your recorded audio is deleted and the display automatically returns to the previous menu. To exit without making changes, press EXIT .
Select music on hold source
1.
When the telephone is idle, press MENU /ENTER .
2.
3.
4.
5.
Press or to scroll to
Press or to scroll to
Base setup . Press
Music on hold
MENU/
. Press
ENTER
MENU/
.
ENTER .
M.O.H. on/off
Review M.O.H.
Record new M.O.H.
> M.O.H. source
Press or to scroll to M.O.H. source . Press MENU/ ENTER .
Press or to highlight Recorded M.O.H.
or Aux In Device .
M.O.H. source
:Recorded M.O.H.
If you select Aux In Device and the HEADSET/AUX IN jack is connected with an audio device, when you press
MENU/ ENTER to save the setting, Device connected to the headset jack will be used for M.O.H.
displays.
ENTER=Save
M.O.H. source
:Aux In Device
ENTER=Save
-OR-
If you select Aux In Device and the HEADSET/AUX IN jack is not connected with an audio device, when you press MENU/ ENTER to save the setting, No Device is connected to the headset jack at base displays.
Connect an audio device to the HEADSET/AUX IN jack (page 24), then choose Review M.O.H.
The screen returns to the previous menu. To exit without making changes, press EXIT .
1.
2.
3.
4.
NOTES:
If you unplug the audio device while a call is on hold, the music on hold source is immediately set to Recorded M.O.H. The screen displays Recorded M.O.H. reconnect. Aux In Device reset source .
If you unplug the audio device while a call is on hold, you can plug a corded headset into the
HEADSET
/AUX IN jack and activate it by pressing HEADSET on the telephone base.
If you select Aux In Device as the music on hold source but you want to use a corded headset, you must turn off the music on hold (see page 23) or change the source to Recorded
M.O.H.
If you try to use a corded headset without changing the setting, To use headset, turn off M.O.H. or reset source. displays with an error tone.
If you unplug your audio device from the telephone base, your music on hold source will automatically be set to Recorded M.O.H.
27
Getting started
Telephone base setup
Call alert tone
When this feature is turned on, you will hear two short beeps when you are on a call on one line and there is an incoming call on another line. You can turn this feature on or off.
1.
2.
When the telephone is idle, press
Press or to scroll to
MENU
Base setup
/ENTER
. Press MENU/
.
ENTER .
3.
Press or to scroll to Call alert tone . Press MENU/ ENTER .
Ringer setting
RestrictedPrefix
Mailbox setup
> Base setup
4.
5.
Press or to select to On or Off .
Press MENU/ ENTER to save the setting and return to the previous menu. There is a confirmation tone. To exit without making changes, press EXIT .
Hold Reminder
Date and time
Music on hold
> Call alert tone
>
Call alert tone
:On
ENTER=Save
28
Getting started
Auto attendant setup (for answering system)
You can set up the auto attendant to answer outside calls, provide callers with a company directory, automatically forward calls to a specified extension, and enable callers to record voice messages when there is no answer. You can use a default outgoing announcement or record up to five announcements of your own. For details on how to use the auto attendant feature, see the Answering system section on pages 75-77 of this user’s manual.
Record announcement (auto attendant)
Use this feature to record up to five new announcements so that you can have different announcements for different lines, or different announcements for daytime and after hours. You can easily switch among the recorded announcements. Each announcement can be up to two minutes.
The auto attendant announcement should contain instructions for the caller.
Following are example scripts.
Default announcement: “Hello, this is the automated attendant. Please enter your party’s extension, followed by pound. If you are using a rotary telephone, please stay on the line. For a company directory, dial star twice.”
If you have many extensions, record a separate extension list (page 30) and reference it in your auto attendant announcement, as shown in Sample announcement 1 . If you have only a few extensions, you can list them in the auto attendant announcement, as shown in Sample announcement 2 without the separate extension list.
Sample announcement 1: “Hello, you have reached XYZ Corp. Please enter your party’s extension, followed by the pound key. To hear a list of extensions, dial star twice.”
Sample announcement 2: “Hello, you have reached XYZ Corp. For sales, press 1, then pound; for service, press 2, then pound; for shipping, press 3, then pound; or press star, then pound for the receptionist.”
1.
When the telephone is idle, press ANSWER ON for the desired line.
2.
Press or to scroll to Setup .
Press MENU/ ENTER .
3.
Press or to scroll to Announcement . Press
MENU/ ENTER .
4.
Press or to scroll to one of the announcements,
Anncemnt 1 through Anncemnt 5 . If no message has been recorded, (none) appears. Press MENU/ ENTER .
5.
Press MENU/ ENTER to start recording. The timer starts counting. Lift the corded handset or face the telephone base to record your announcement.
29
Mailbox setup
Auto attendant
Annc only
> Announcement
> Anncemnt 1 (none)
Anncemnt 2 (none)
Anncemnt 3 (none)
Record anncemnt 1
ENTER=Start
Getting started
Auto attendant setup (for answering system)
6. Press MENU/ ENTER to stop recording. The timer stops and the recorded announcement automatically plays back.
7. Press 2 to save the setting and return to the previous menu, or press 1 to record that announcement again.
Record anncemnt 1
00:11
ENTER=Stop
Play anncemnt 1
00:03
NOTE: Once you have recorded an announcement, (none) disappears .
1=Change 2=OK
> Anncemnt 1
Anncemnt 2 (none)
Anncemnt 3 (none)
Record extension list
Use this feature to record a list of your phone extensions that plays when the auto attendant answers a call and the user presses star twice. Use this auto attendant option when you do not want to list extension numbers in the initial message that callers hear.
Sample extension list: “For sales, press 1, then pound; for service, press 2, then pound; for shipping, press 3, then pound; or press star, then pound for the receptionist.”
1.
When the telephone is idle, press ANSWER ON for the desired line.
2.
3.
4.
5.
Press or to scroll to Setup .
Press MENU/ ENTER .
Press or to scroll to Record ext list . Press MENU/ ENTER .
The current extension list plays.
>
Auto attendant
Annc only
Announcement
Record ext list
Press 1 to select Change .
Press MENU/ ENTER to start recording. The timer starts counting. Lift the corded handset or face the telephone base to record your extension list.
Record ext list
00:05
1=Change 2=OK
Record ext list 6.
Press MENU/ ENTER to stop recording. The timer stops and the recorded message automatically plays back.
7.
Press 2 to save the setting and return to the previous menu, or press 1 to record the message again.
ENTER=Start
Record ext list
00:17
ENTER=Stop
NOTE: The auto attendant and the private mailboxes for all extensions share the same list of announcements.
30
Getting started
Auto attendant setup (for answering system)
Number of rings (auto attendant)
Use this feature to set the number of times the telephone rings before the auto attendant answers. The number of rings can be between 2 and 7.
1.
When the telephone is idle, press ANSWER ON for the desired line.
2.
Press or to scroll to Setup. Press MENU/ ENTER .
Ans->Auto att
Ans->Annc only
>
No answer
Setup
3.
Press or to scroll to Auto attendant .
Press MENU/ ENTER .
Mailbox setup
> Auto attendant
Annc only
Announcement 4.
Press MENU/ ENTER again to select Number of rings .
5.
Press or to select a number ( 2 7 ).
> Number of rings
Select anncemnt
6.
Press MENU/ ENTER to save the setting and return to the previous menu. There is a confirmation tone. To exit without making changes, press EXIT .
Number of rings
:2
ENTER=Save
31
Getting started
Mailbox setup (for answering system)
You can set each telephone line mailbox separately. By default, lines 1, 2, 3, and 4 are not set to answer; the answering system is disabled and any calls to those lines will ring on all extensions.
Number of rings (general mailbox)
Use this feature to set the number of times the telephone rings before the mailbox answers. The number of rings can be between 2 and 7. You can also select Toll saver , which is explained below. Unless you change it, the general mailbox answers an incoming call after four rings.
1.
When the telephone is idle, press ANSWER ON for the desired line.
4.
Press MENU/ ENTER again to select Number of rings .
> Mailbox setup
Auto attendant
Annc only
Announcement 2.
Press or to scroll to Setup. Press MENU/ ENTER
3.
Press MENU/ ENTER to select Mailbox setup or Annc only .
> Number of rings
Select anncemnt
5.
Press or to scroll to a number ( 2 7 ) or Toll saver .
• Toll saver - the answering system answers a call after two rings when there are new messages, and after four rings when there are no new messages. This enables you to check for new messages without paying for a toll call.
6. Press MENU/ ENTER to save the setting and return to the previous menu. There is a confirmation tone. To exit without making changes, press EXIT .
Number of rings
:5
ENTER=Save
Number of rings
:Toll saver
ENTER=Save
Number of rings (announce only)
Use this feature to set the number of times the telephone rings before the answering system plays the announcement only. The number of rings can be between 2 and 7. By default, the answering system plays the announcement only after two rings.
1.
When the telephone is idle, press ANSWER ON for the desired line.
2.
Press or to scroll to Setup. Press MENU/ ENTER
3.
4.
Press
Press
MENU/
MENU/
ENTER to select
ENTER
Annc only again to select
.
Number of rings .
Mailbox setup
Auto attendant
> Annc only
Announcement
5.
Press or to scroll to a number ( 2 7 ).
6. Press MENU/ ENTER to save the setting and return to the previous menu.
There is a confirmation tone. To exit without making changes, press EXIT .
32
Getting started
Mailbox setup (for answering system)
Record announcement (independent mailbox)
Use this feature to record up to five new announcements so that you can have different announcements for different lines. Each announcement can be up to two minutes. Please see Record announcement (auto attendant) for detailed instructions on page 29.
NOTE: You cannot record an announcement when the telephone system is out of space.
You will hear “Memory is full.” Please refer to Remaining space on page 38.
Select announcement
Use this feature to select an announcement for your independent mailbox from the list of announcements.
1.
When the telephone is idle, press ANSWER ON for the desired line.
2.
Press or to scroll to Setup. Press MENU/ ENTER .
Mailbox setup
> Auto attendant
Annc only
Announcement
3.
Press MENU/ ENTER again to select Mailbox setup .
4.
Press or to scroll to Select anncemnt . Press MENU/ ENTER .
Number of rings
> Select anncemnt
5.
Press or to scroll to an announcement.
6.
Press MENU/ ENTER to save the setting and return to the previous menu. The selected announcement plays. To exit without making changes, press EXIT .
Select anncemnt
:Prerecord
ENTER=Save
NOTE: The announcements can be used for the auto attendant, general mailbox and the announce only answer mode.
Select anncemnt
:Anncemnt 1
ENTER=Save
33
Getting started
Mailbox setup (for general mailbox)
Set access code (remote code)
Use this feature to enter a four-digit number (0000-9999) to allow remote access to your general mailbox from any touch-tone telephone. Unless you change it, the remote access code is 0000.
1.
2.
3.
4.
When the telephone is idle, press MENU /ENTER .
Press or to scroll to Mailbox setup . Press MENU/ ENTER .
>
Directory
Call log
Ringer setting
Mailbox setup
Press MENU/ ENTER again to select Set access code .
Use the dial pad to enter a four-digit number. Use
REMOVE to backspace and delete a digit.
> Set access code
Call screening
Persistent hold
Notify alert
5.
Press MENU/ ENTER to save the setting and return to the previous menu. There is a confirmation tone. To exit without making changes, press EXIT .
Enter mailbox access code:
0000
ENTER=Save
NOTES:
1.
2.
The access code must have four digits.
You will hear an error tone if you enter an access code that is already assigned.
Enter mailbox access code:
9999
ENTER=Save
Call screening
Use this feature to choose whether incoming messages can be heard over the speaker as they are being recorded. If you turn call screening on, you hear the incoming message.
If more than one incoming message comes from different telephone lines at the same time, only the first incoming message is monitored. While the telephone is recording the monitored message, you can answer the call by lifting the corded handset or by pressing SPEAKER .
If you want to mute the message playback, press MUTE on the telephone base.
Follow the steps to turn the call screening on or off:
1.
When the telephone is idle, press MENU /ENTER .
2.
3.
4.
Press or to scroll to Mailbox setup. Press MENU/ ENTER .
Press or to scroll to Call screening . Press MENU/ ENTER .
> Call screening
Persistent hold
Notify alert
Press or to highlight On or Off .
Set access code
5.
Press MENU/ ENTER to save the setting and return to the previous menu. There is a confirmation tone. To exit without making changes, press EXIT .
Call screening
:On
ENTER=Save
34
Getting started
Mailbox setup (for general mailbox)
Persistent hold
By default, a call on hold after 10 minutes is automatically forwarded to the auto attendant, even if the auto attendant is not on for that line. When
Persistent hold is enabled, the call stays on hold until it is released or hung up.
1.
When the telephone is idle, press MENU /ENTER .
2.
Press or to scroll to Mailbox setup. Press
MENU/ ENTER .
Set access code
Call screening
> Persistent hold
Notify alert
3.
4.
5.
Press or to scroll to Persistent hold . Press
MENU/ ENTER .
Persistent hold
:off
Press or to highlight Off or On .
ENTER=Save
Press MENU/ ENTER to save the setting and return to the previous menu. There is a confirmation tone. To exit without making changes, press EXIT .
35
Notify alert
Use this feature to receive notification calls to any phone number you set
(such as a cellular phone or paging device) after a new message has been recorded to the general mailbox. To receive notification calls, you must save the number you wish to be notified at to the telephone base, and then set the system to call this number after it finishes recording a message.
If the number called has caller ID service, there will be an indication of the notification call. When you receive a notification call, you hear about 15 seconds of silence; then the call is ended. There is no message sent and the call is only made once. If the call is not picked up within three rings, the telephone base cancels the call. You may not receive the call if the number you set is busy, not available or off during the call.
1.
When the telephone is idle, press MENU /ENTER .
2.
3.
Press or to scroll to Mailbox setup .
Press MENU/ ENTER .
Press or to scroll to Notify alert . Press MENU/ ENTER .
Set access code
Call screening
Persistent hold
> Notify alert
Set alert number:
1.
Press MENU/ ENTER again to select Alert call # .
2.
Use the dial pad to enter the number (up to 32 digits) of the cellular phone or paging device you want to be notified.
> Alert call #
Alert on/off
Calling alert #
• Press REMOVE to backspace and delete a digit.
• Press REP or SKIP to move the cursor to the left or right.
3. Press MENU/ ENTER to save the setting and return to the previous menu.
There is a confirmation tone. To exit without making changes, press EXIT .
Turn alert on or off:
1. Press or to scroll to Alert on/off . Press MENU/ ENTER .
2. Press or to scroll to On or Off .
3. Press MENU/ ENTER to save the setting and return to the previous menu. There is a confirmation tone. To exit without making changes, press EXIT .
Alert on/off
:On
ENTER=Save
36
Getting started
Mailbox setup (for general mailbox)
Call alert confirmation:
You can confirm whether the system can successfully call the alert number that you entered.
Alert call #
1.
Press or to scroll to Calling alert # .
Press MENU/ ENTER . Alert on/off
> Calling alert #
2.
The screen displays Press SPKR to confirm the alert call .
3.
Press SPEAKER on the telephone base. You should hear the telephone number being dialed. To exit without making changes, press EXIT .
Press SPKR to confirm the alert call
4.
After confirming that the call went to the telephone number you specified, press SPEAKER again to end the test. The screen returns to idle mode.
1.
2.
3.
NOTES:
Calling alert #
If you turn on Notify alert before you enter the alert number, Please set the alert #. appears on the screen.
The called telephone hears silence when the system calls the alert number.
To initiate a call alert call again, do the first three steps of the Call alert confirmation section (above).
Voice language
You can select a language ( English , Spanish or French ) to be used for the voice prompts in the answering system.
1.
When the telephone is idle, press MENU /ENTER .
2.
Press or to scroll to Mailbox setup. Press
MENU/ ENTER.
3.
Press or to scroll to Voice language . Press
MENU/ ENTER .
4.
Press or to select English , Español or Français .
5.
Press MENU/ ENTER again to save the setting and return to the previous menu. There is a confirmation tone.
To exit without making changes, press EXIT .
>
Persistent hold
Notify alert
Voice language
Remaining space
Language
:English
ENTER=Save
37
Getting started
Mailbox setup (for general mailbox)
Remaining space
Use this feature to check the amount of space currently in the system for the estimated remaining recording time and number of messages.
1.
When the telephone is idle, press MENU /ENTER .
2.
Press or to scroll to Mailbox setup. Press MENU/ ENTER.
Directory
Call log
Ringer setting
> Mailbox setup 3.
Press or to scroll to Remaining space . Press
MENU/ ENTER .
4.
After checking the screen display, press REP to return to the previous menu.
Persistent hold
Notify alert
>
Voice language
Remaining space
Remaining space
Time: 175 min
Messages: 243
38
Getting started
Mailbox setup (for handset/deskset)
You can access handset/deskset mailboxes from the telephone base. For detailed instructions, refer to Handset mailbox overview in the SynJ
SB67108 handset user’s manual or Deskset mailbox overview in the SynJ
SB67148 deskset user’s manual.
Fast answer mode
When fast answer mode is turned on for any extension, calls to that extension are answered by the auto attendant after 2 rings. When turned off, calls are answered by the auto attendant after 5 rings. Please refer to Fast answer mode on or off in the SynJ
SB67108 handset user’s manual or the SynJ SB67148 deskset user’s manual for more information.
Enter mailbox access code:
0001
ENTER=Next
1.
When the telephone is idle, press (Messages) on the telephone base.
2.
Press the one-touch EXT 1-0 key for the destination extension mailbox.
2 New messages
Handset anncemnt
To general MBox
3.
Use the dial pad to enter the four-digit remote access code of the extension. Use REMOVE to backspace and delete a digit. Press MENU/ ENTER .
4.
Press or to scroll to Fast answer mode .
Press MENU/ ENTER .
5.
Press or to select On or Off .
Fast answer mode
:On
ENTER=Save
6.
Press MENU/ ENTER to save the setting and return to the previous menu.
There is a confirmation tone. To exit without making changes, press EXIT .
Handset/deskset announcement setup
The announcement is the greeting callers hear when calls are answered by the handset/deskset mailbox. You can set or change handset/deskset announcement using the telephone base.
The default announcement is “Hello, please leave a message after the tone.”
You can use this announcement or replace it with your own recording.
Your announcement can be up to two minutes.
1.
When the telephone is idle, press (Messages) on the telephone base.
2.
Press the one-touch EXT 1-0 key for the destination extension mailbox.
3.
4.
Use the dial pad to enter the four-digit remote access code of the extension. Use REMOVE to backspace and delete a digit.
Press MENU/ ENTER .
2 New messages
Press or to scroll to
MENU/ ENTER .
Handset anncemnt .
Press
Play all
Deliver
39
Getting started
Mailbox setup (for handset/deskset)
1.
The system automatically plays the current handset announcement. A timer appears on the screen and starts counting. The screen displays 1=Change 2=OK .
2.
Press 1 to record that announcement again. The screen displays Record anncemnt ENTER=Start . Press
MENU/ ENTER . The system announces “ Record after the tone. Press stop when you are done .” You hear a reminder beep and the timer starts counting.
Lift the corded handset or face the telephone base to record your announcement.
3.
Press MENU/ ENTER when finished. The timer stops and the recorded announcement automatically plays back.
4.
Press 2 to use the new recorded announcement.
-OR-
Press 1 to record that announcement again.
Play announcement
00:09
1=Change 2=OK
Record anncemnt
ENTER=Start
Record anncemnt
00:05
ENTER=Stop
Play announcement
00:02
1=Change 2=OK
Switch to general mailbox
You can directly access the general mailbox of any handset or deskset using the telephone base.
1.
When the telephone is idle, press (Messages) on the telephone base.
2.
Press the one-touch EXT 1-0 key for the destination extension mailbox.
3.
Use the dial pad to enter the four-digit remote access code of the extension. Use REMOVE to backspace and delete a digit. Press MENU/ ENTER .
4.
Press or to scroll to To general MBox .
Press MENU/ ENTER .
-OR-
To exit without making changes, press EXIT .
1 New messages
Deliver
Handset anncemnt
5 New messages
Deliver
Delete all old
40
Getting started
Speed dial setup
The telephone base has 10 speed dial locations where you can store the telephone numbers you wish to dial using fewer keys than usual. You can store up to 32 digits in each location.
Enter, edit or delete a speed dial number
1.
When the telephone is idle, press MENU /ENTER .
2.
Press or to scroll to Speed dial setup. Press MENU/ ENTER.
3.
Press or to choose the desired speed dial location, then press MENU/ ENTER .
Mailbox setup
Base setup
COVM
> Speed dial setup
4.
Use the dial pad to enter or edit the telephone number up to 32 digits. If you want to delete the entry, erase all the digits.
> Speed dial 1
Speed dial 2
Speed dial 3
Speed dial 4
• Enter phone #:
8888832445
•
•
Press REP or SKIP to move the cursor to the left or right.
Press REMOVE to backspace and delete a digit.
Press and hold REMOVE to delete all digits.
ENTER=Save
Enter phone #:
8888832445
5. Press MENU/ ENTER to save the setting and return to the previous menu. There is a confirmation tone. To exit without making changes, press EXIT .
ENTER=Save
1.
2.
NOTES:
See Calling a speed dial number on page 45 for instructions on calling a speed dial number.
The memory locations for speed dial and the directory are not the same, so setting up speed dial numbers does not decrease your directory storage space.
Customer support
Use this feature to display the AT&T website.
1.
When the telephone is idle, press MENU /ENTER .
2.
Press to scroll to Customer support .
Press MENU/ ENTER .
3.
To exit, press EXIT .
Base setup
COVM
Speed dial setup
> Customer support www.telephones
.att.com
41
Getting started
Screen icons, indicator tones and lights
-MUTE
-PRIV
-REC
Conf.
COVM
AuAt
LineX
Screen icons:
1 2 3 4 5
6 7 8 9 0
On when any corresponding extensions are in use.
Ringer off - the telephone base ringer is off or the do not disturb function is on.
Microphone is muted.
1 2 3 4 5 6 7 8 9 0
Line1
-PRIV -MUTE -Rec
AuAt COVM COVM AuAt
Call privacy is on.
The call is being recorded.
A three-way conference call is active.
There is new voicemail for the telephone line below the
COVM indicator.
Auto attendant is on for the telephone line below the
AuAt indicator.
The line is in use (X is the telephone line number).
Indicator tones:
One short beep
Hold reminder tone
(a triple beep)
Error tone
(a triple beep)
Four beeps
Confirmation tone
The telephone conversation recording begins. During the recording, you will hear one beep per minute.
The Hold reminder is active; a call has been on hold for more than three minutes.
•
•
You press VOL+ or VOL and the volume has reached its highest or lowest setting.
You press CALL LOG and the call log is empty.
You cannot intercom with an extension when it is set to Privacy ON .
Command completed successfully.
42
Getting started
Screen icons, indicator tones and lights
Indicator lights:
Lighted display
LINE 1-LINE 4 indicator
On when a telephone line is in use.
Flashes slowly when a telephone line is on hold.
Flashes rapidly when there is an incoming call.
ANSWER ON indicator
On when the general mailbox is on and ready to receive calls.
NEW CALL indicator
On when there are new or missed calls in the call log.
( Messages) indicator
Flashes when there are new or missed messages in the general mailbox.
HEADSET indicator
On when the corded headset is in use.
DND indicator
On when the do not disturb function is on.
MUTE indicator
Flashes slowly when the corded handset microphone or speakerphone is muted.
SPEAKER indicator
On when the speakerphone is on.
43
Telephone base operation
Telephone base basic operation
The telephone comes programmed to use line 1 (default primary line) for calls when you do not press a line key. (To change the primary line, see
Line selection on page 20.) When you answer a call, the telephone automatically selects the ringing line.
•
•
•
•
Line indicators
Each of the four indicators on LINE 1 LINE 4 indicate the state of the corresponding telephone line.
•
On when the corresponding line is in use.
Flashes slowly when the line is on hold.
Flashes slowly when there is a transferred call on the corresponding line.
Flashes slowly when there is an incoming auto attendant transferred call on the corresponding line.
Flashes rapidly when there is an incoming call on the corresponding line.
Making a call
To make a call from the telephone base:
1.
Lift the handset or press SPEAKER.
-OR-
To override automatic line selection, press LINE 1 LINE 4 for the desired line, then lift the handset.
Elapsed time 2. Wait for a dial tone, then enter the telephone number.
The screen displays the elapsed time as you talk
(in hours, minutes and seconds).
Line1 00:00:27
8888832445
To end a call from the telephone base:
Place the handset on the telephone base to hang up.
-OR-
If you are using the speakerphone, press
SPEAKER to hang up.
NOTE: The elapsed time is not affected by accessing services from your telephone service provider.
44
Telephone base operation
Telephone base basic operation
To make a call with a corded headset:
Make sure a corded headset is connected to the telephone base (page 14).
1.
Press HEADSET on the telephone base.
2.
Wait for a dial tone, then dial the number.
3.
To hang up, press HEADSET.
To make a call with a cordless headset:
You can make a call using a registered cordless headset and the dial pad on the telephone base.
1.
Press the ON /OFF button on the cordless headset.
2.
Wait for a dial tone, then dial the number on the base.
3.
To hang up, press the ON/ OFF button .
On hook dialing (predialing)
1.
Enter the telephone number. Press REMOVE to delete any misdialed digits and make corrections, if needed.
2.
Lift the handset or press SPEAKER to dial.
-OR-
To override automatic line selection, press LINE 1 LINE 4 for the desired line, then lift the handset.
Using the speakerphone
During a call, press SPEAKER to switch between handsfree speakerphone and normal handset use. Press SPEAKER again or place the handset on the telephone base to hang up.
Calling a speed dial number
1.
Press and hold a dial pad key ( 1 0 ) to display the speed dial number.
2.
Lift the handset, press SPEAKER or HEADSET .
-OR-
To override automatic line selection, press LINE 1 -
LINE 4 for the desired line, then lift the handset.
Speed dial 3
88888 32445
Line 3
8888832445
NOTE: If there is no telephone number stored in the speed dial location,
No number displays on the screen.
Speed dial 4
No number
45
Telephone base operation
Telephone base basic operation
Answering a call
To answer a call:
• Lift the handset, press SPEAKER , HEADSET or the
ON /OFF button on a registered cordless headset.
-OR-
To override automatic line selection, press LINE 1 LINE 4 for the desired line, then lift the handset.
Temporary ringer silencing
Press MUTE while the telephone is ringing to silence the ringer temporarily on the telephone base only. This turns off the ringer without disconnecting the call. The next incoming call rings normally at the preset volume.
Last number redialing
The last 10 telephone numbers dialed (up to 32 digits) are stored in system memory.
To view the 10 most recently dialed numbers:
1. Press PAUSE/ REDIAL to enter the redial list and display the most recently called number.
2. Press or , or press PAUSE/ REDIAL repeatedly to view other recently called numbers.
3. Press EXIT to exit the redial list.
To redial a number:
8888832445
•
• Line1
8888832445
To edit a number:
While the desired number displays, press MENU/ ENTER to enter editing mode.
•
•
• lift the handset, or press SPEAKER or HEADSET .
To override automatic line selection, press LINE 1 LINE 4 for the desired line, then lift the handset.
•
Press REP or SKIP to move the cursor to the left or right.
Press REMOVE to backspace and delete a digit.
Press PAUSE /REDIAL dialing pause (a P appears) (page 62).
Press FLASH to enter a flash (page 62).
8888832445
To delete a number:
• While the screen displays the desired number, press
REMOVE to delete the number from the redial memory.
46
Deleted
Telephone base operation
Options while on calls
Volume control
While on a call, press VOL+ or VOL- to adjust the listening volume.
Volume
1.
2.
NOTES:
The corded headset and corded handset volume settings are the same, but they are independent from the speakerphone.
While using the volume control, you hear a triple beep when you have reached the minimum or maximum level.
Call waiting
If you subscribe to call waiting service with your telephone service provider, and someone calls while you are in the middle of a call, you hear a beep.
•
•
Press FLASH to put your current call on hold and take the new call.
Press FLASH at any time to switch back and forth between calls.
1.
2.
NOTES:
If you miss a call while the line is in use, the caller ID of the missed call displays for 15 seconds after your current conversation ends.
For more information on caller ID with call waiting, see page 66.
47
Telephone base operation
Options while on calls
Call privacy
To ensure call privacy, this telephone allows only one set at a time to use a line. You can also block all system handsets from joining a phone conversation (see page 51 for instructions for joining calls).
To enable call privacy:
• During the call, press MENU privacy .
The screen displays -PRIV . Any other extensions are dropped and no extensions can join the call. If another extension tries to access the line you are using, its screen displays Privacy .
/ENTER twice to select call
> Privacy ON
Record call ON
Line1 00:00:06
8888832445
-PRIV
To cancel call privacy:
• During the call, press MENU /ENTER twice to cancel call privacy and continue with the conversation. The icon
-PRIV disappears from the screen. Other telephones can now join the call by pressing the appropriate line key.
> Privacy OFF
Record call ON
NOTES:
1.
2.
3.
Call privacy is automatically canceled when you end or transfer a call.
You cannot set call privacy during intercom or conference calls.
Call privacy applies only to system telephones. It does not affect non-system phones using the same line(s).
Line1 00:10:06
8888832445
48
Telephone base operation
Options while on calls
Recording a call
Use this feature to record two-way phone conversations during a call. The recording is treated the same as memos and is always marked as a new message in the mailbox. However, the (Messages) indicator does not flash for new or missed recorded calls. You cannot record a conference call or an intercom call and you cannot use another line while you are recording a phone conversation.
To record a call:
1.
While on a call, press MENU /ENTER .
2.
Press or to scroll to Record call ON . Press MENU/ ENTER .
Privacy ON
> Record call ON
3.
The recording starts and the system activates call privacy. The screen displays -PRIV and -REC , and the timer starts counting while recording.
4.
To stop recording and continue the call, press MENU/ ENTER twice. The system saves the conversation into the general mailbox.
-OR-
Line1 00:00:06
-PRIV -REC
> Record call OFF
The recording ends when you disconnect the call.
While recording a phone conversation:
The other party hears a short beep when the recording begins and once each minute during the recording. To ensure compliance with state and federal regulations regarding the recording of a telephone call, you should start the recording process and inform the caller that you are recording the call.
To play back a memo or phone conversation:
Play memos or two-way phone conversations the same way as messages are played. (see Message playback on page 78).
1.
2.
NOTES :
Call privacy is automatically on when recording a call.
Calls that you record use the same memory as the answering system. Recording long conversations uses up space otherwise available for recording normal messages. Please see Remaining space on page 38.
49
Telephone base operation
Options while on calls
Mute
Use this feature during a telephone conversation to silence the microphone. You can hear the caller, but the caller cannot hear you.
To mute a call:
• Press MUTE . When mute is on, the MUTE light flashes; the screen also flashes -MUTE .
To take a call off mute:
• Press MUTE again and resume speaking.
Line1 00:05:40
8888832445
-MUTE
NOTE: Transferring the call, changing lines or putting a call on hold also cancels the mute function.
Hold
Use this feature to hold one line while accessing another, or as part of the conference and call transfer features.
While on a call, press and release HOLD . The LINE 1 LINE 4 indicator for the line on hold flashes slowly in red. After the call has been on hold for more than three minutes, you will hear a triple beep every 30 seconds. (To adjust the volume of the reminder tone or turn it off, see Hold reminder on page 22).
If you are using the speakerphone, the speakerphone turns off automatically when you press HOLD .
To release the hold, press and release LINE 1 LINE 4 of the call on hold.
Hold Line1
NOTES:
1.
2.
By default, a call on hold after 10 minutes is automatically forwarded to the auto attendant, even if the auto attendant is not activated for that line. If Persistent hold is enabled (see page 35), the call will stay on hold until it is released or hung up. To keep a call on hold longer than 10 minutes, you can also release the held call within 10 minutes and then place the call on hold again.
You cannot put an intercom call on hold.
Switching between lines
Use this feature to switch between lines during an outside call:
1.
Press LINE 1 LINE 4 of another telephone line to make or answer another call. The current call is put on hold automatically.
2.
To return to the first call, press the original LINE 1 LINE 4 . The second line is put on hold automatically.
50
Telephone base operation
Options while on calls
Join a call in progress
Use this feature to join in an ongoing call on any line that does not have call privacy set (see Call privacy on page
48 for more information). The corresponding line icon appears on the screen when the line is in use.
• Press and hold the desired LINE 1 LINE 4 on the telephone base to join in the call, which becomes a three-way conference (page 51).
1
Conf. 00:00:29
L3 H2
1
Privacy
NOTE: When you try to join an ongoing call on a line with call privacy on, the screen displays Privacy and you hear four beep tones.
Chain dialing
While you are on a call, you can initiate a dialing sequence from the numbers in the directory.
Chain dialing can be useful if you wish to access other numbers (such as bank account numbers or access codes) from the directory.
To access the directory while on a call:
1.
During the call, press DIR review the directory.
2.
To dial the displayed number, press MENU/ ENTER. To exit without making changes, press EXIT or REP and continue with the conversation.
CHRISTINE SMITH
8887227702
ENTER=Call
Line1 00:16:30
88324458887227702
NOTE: You cannot edit a directory entry while on a call. See page 65 for more details about the directory.
Three-way conference calls
Use this feature to set up a three-party call by using two lines at the same time. You can also join an intercom call with a call on an outside line. The outside line call must be established first because an intercom call cannot be placed on hold.
51
Telephone base operation
Options while on calls
To make a three-way conference call:
1.
2.
3.
Make or answer an outside call.
Press HOLD and call someone on another line, or start an intercom connection.
-OR
Call someone on another line, or intercom someone. The first line is automatically put on hold.
Press CONF at any time to begin the three-party conference.
1
Conf. 00:00:35
L1 H1
To talk privately with one external party:
1.
2.
3.
Press HOLD to place both lines on hold.
Press LINE 1 LINE 4 to talk privately with the person on that line.
Press CONF to resume the conference call.
To talk privately with one internal party:
1.
2.
Press HOLD to talk privately with the person on that handset/deskset. The external line is automatically placed on hold.
Press CONF to resume the conference call.
To drop one line:
1.
2.
Press LINE 1 LINE 4 to activate the line you want to drop and place the handset on the telephone base to hang up or press SPEAKER . The other line is put on hold automatically.
Press LINE 1 LINE 4 to resume the call and lift the handset on the telephone base.
To drop an intercom:
• Press LINE 1 LINE 4 to activate the external call. The intercom call drops automatically.
To end a conference call:
• Place the handset on the telephone base to hang up or press
SPEAKER . The call does not terminate until all extensions hang up.
1.
2.
3.
NOTES:
If an internal party hangs up, the ongoing call becomes a two-way conversation.
You cannot make any conference calls if all four telephone lines are in use.
If you are experiencing difficulty in using the conference features on this telephone, please consider using AT&T’s complete line of teleconference services to find a solution that best meets your needs. AT&T TeleConference Services reduces travel time and expenses while increasing productivity wherever people are located, enabling you to host truly virtual meetings and share important information in real time. To sign up for AT&T TeleConference Services, go to: www.att.com/orderconference
for details.
52
Telephone base operation
COVM
COVM (central office voicemail)
If you subscribe to voicemail service with your telephone service provider, turn on the COVM feature.
This feature displays COVM on the screen above the line key of any telephone line that receives new voicemail messages.
*: Base
0 Missed calls
2:43PM 1/13
COVM COVM
If you do not subscribe to voicemail service or want to disable the indicator, turn off the COVM feature.
Ringer setting
1.
When the telephone is idle, press MENU /ENTER . Mailbox setup
Base setup
2.
Press or to scroll to COVM .
Press MENU/ ENTER .
> COVM
3.
Press MENU/ ENTER again to select COVM on/off .
4.
Press or to select On or Off .
5.
Press MENU/ ENTER to save the setting and return to the previous menu. There is a confirmation tone. To exit without making changes, press EXIT .
> COVM on/off
COVM reset
COVM
:On
ENTER=Save
COVM reset
Use this feature when the telephone indicates there is new voicemail but there is none. For example, when you have accessed your voicemail while away from the building. This feature only turns off the COVM indicator; it does not delete your voicemail messages. As long as you have new voicemail messages, your telephone service provider continues to send the signal to turn on the indicator. You can reset COVM indicators individually or for all the telephone lines using the All COVM reset command.
1.
When the telephone is idle, press MENU /ENTER .
COVM on/off
> COVM reset
2.
Press or to scroll to COVM .
Press MENU/ ENTER .
3.
4.
Press or to scroll to COVM reset . Press MENU/ ENTER .
Press or to scroll to COVM 1 reset COVM 4 reset to clear the COVM indicator of a telephone line, or scroll to All COVM reset to clear the indicators for all the line.
> COVM 1 reset
COVM 2 reset
COVM 3 reset
COVM 4 reset
5.
Press MENU/ ENTER to execute the command and return to the previous menu. There is a confirmation tone. To exit without making changes, press EXIT .
>
COVM 2 reset
COVM 3 reset
COVM 4 reset
All COVM reset
NOTE: For information about using your voicemail service, contact your telephone service provider for assistance.
53
COVM reset
Telephone base operation
Intercom
You can use the intercom feature for conversations between the telephone base and an accessory device, or between two accessory devices. When the system is on one or more external calls, accessory devices can make intercom calls with each other. If you have a cordless headset, it can only receive intercom calls.
Each device that is registered to the telephone base is assigned an extension.
Extension numbers are assigned in sequential order (0-9) as they are added.
If you register a cordless headset, it is always assigned extension number 0.
See pages 10-12 for information on adding and registering devices to your telephone base.
NOTE: A telephone base connected to AC power but not to any telephone lines can still make intercom calls with charged and registered accessory cordless accessory.
Make an intercom call to a cordless handset/deskset
Press the one-touch EXT 1 0 key for the destination extension or press the
INT/PTT ALL key, then lift the handset. The screen displays Calling X:Handset X ( X represents the extension number [ 1 0 ], Handset X represents the handset name),
Calling X:Deskset X ( X represents the extension number
[ 1 0 ], Deskset X represents the deskset name) or
Calling All .
Intercom to:
> Handset 1
Deskset 2
Handset 3
Calling
1:Handset 1
-OR-
Press INT key on the telephone base, then scroll to the destination extension. Press MENU/ ENTER .
1.
2.
3.
4.
5.
NOTES:
Before the intercom call is answered, you can cancel the intercom by pressing SPEAKER , lifting and resetting the handset, or by pressing the corresponding LINE 1 LINE 4 to resume a call.
The intercom call automatically cancels if the call is unanswered after one minute.
Press MUTE to temporarily silence the intercom ringer.
When you choose All in the menu, all the extensions and the telephone base ring. The intercom call is established with the first extension to answer the call.
If a line is in use, pressing INT places the line on hold and activates the intercom.
54
Telephone base operation
Intercom
Answer an intercom call
When you receive an intercom call, you hear a ringing tone and your screen displays Call X: Handset X ( X represents the extension number [ 1 0 ],
Handset X represents the handset name) or Call X: Deskset X ( X represents the extension number [ 1 0 ], Deskset X represents the deskset name).
Answer an intercom call just as you would answer a normal call.
End an intercom call
Make another intercom call while on an intercom call
You can make an intercom call to another destination extension while on an intercom call. The first intercom automatically disconnects. While on an intercom call:
Press the one-touch EXT 1 0 key or the INT/PTT ALL key for another destination extension. The screen displays Calling X:Handset X ( X represents the extension number [ 1 0 ], Handset X represents the handset name),
Calling X:Deskset X ( X represents the extension number [ 1 0 ], Deskset X represents the deskset name) or Calling All .
-OR-
Press INT on the telephone base, then scroll to the destination extension.
Press MENU/ ENTER .
1.
2.
3.
4.
NOTES:
Before the intercom call is answered, you can cancel the intercom by pressing SPEAKER , lifting and resetting the handset, or by pressing the corresponding LINE 1 LINE 4 to resume a call.
The intercom call automatically cancels if the call is unanswered after one minute.
Press MUTE to temporarily silence the intercom ringer.
When you choose All in the menu, all the extensions and the telephone base ring. The intercom call is established with the first extension to answer the call.
Answer an incoming call during an intercom call
If you receive an incoming outside call during an intercom call, there is an alert tone.
To answer the call, press LINE 1 LINE 4 . The intercom call ends automatically.
55
Telephone base operation
Call transfer
You can transfer a call to any other system telephone. Once you transfer a call, it can be answered by any system telephone, not just at the extension you called.
Blind transfer
While on a call, you can transfer a call directly without notifying the desired extension:
1.
Press XFER on the telephone base.
2.
Press the one-touch EXT 1-0 for the desired extension.
-OR-
>
Transfer to:
Handset 1
Handset 2
Handset 3 press MENU/ ENTER.
3. The current line is put on hold. The destination handset rings and the call is answered by pressing L 1 L 4 . You hear a short tone from the telephone base. The outside call is automatically transferred to the desired extension.
Calling
1:Handset 1
Hold Line1
4. Put the corded handset on the telephone base or press
SPEAKER to hang up.
-OR-
You can resume the call by pressing the corresponding flashing line key
LINE 1 LINE 4 before the desired extension answers the call.
You hear a triple beep every 30 seconds when a transferred call has not been answered (To adjust the volume of the reminder tone or turn it off, see
Hold reminder on page 22).
NOTES:
1.
2.
If the desired extension does not answer the intercom call within one minute, the extension rings as an incoming call to remind the extension user.
If the outside call is put on hold for 10 minutes and Persistent hold is disabled (see page 35), it is
The telephone base returns to idle mode.
Transfer a call and speak to the receiving party
You can transfer a call and speak to the receiving party before completing the transfer while on a call:
1.
Press XFER on the telephone base.
2.
Press the one-touch EXT 1-0 for the desired extension.
56
Telephone base operation
Call transfer
-ORpress MENU/ ENTER.
3. The current line is put on hold. The destination extension rings and the call is answered. You can announce the call. There is an intercom call between the corded handset and the extension.
4. Put the corded handset on the telephone base or press
SPEAKER to hang up. The outside call is automatically transferred to the desired extension.
>
Transfer to:
Handset 1
Handset 2
Handset 3
-OR1
Intercom 00:00:28
You can resume the call by pressing the corresponding flashing line key LINE 1 LINE 4 before the desired extension answers the call.
Hold Line 1
You hear a triple beep every 30 seconds when a transferred call has not been answered (To adjust the volume of the reminder tone or turn it off, see
Hold reminder on page 22).
1.
2.
NOTES:
If the desired extension does not answer the intercom call within one minute, the extension rings as an incoming call to remind the extension user.
If the outside call is put on hold for 10 minutes and Persistent hold is disabled (see page 35), it is
The telephone base returns to idle mode.
Answer a transferred call
When you hear a short intercom ring from the telephone base:
Lift the handset to intercom with an extension. You can talk privately with the extension before picking up the outside call that is on hold. Press the blinking LINE 1 LINE 4 when you are ready to talk to the outside call.
Other options for answering the transferred call:
•
•
•
To answer using the telephone base speakerphone, press before pressing LINE 1 LINE 4 .
SPEAKER
To answer handsfree using the corded headset, press HEADSET before pressing LINE 1 LINE 4 .
To answer handsfree using the cordless headset, press ON /OFF on the headset before pressing LINE 1 LINE 4.
57
Telephone base operation
Push to talk (PTT) intercom
You can directly broadcast messages to the speakerphone of any extension.
The extension you called can respond by pressing the INT key to begin a twoway communication. Any registered cordless handset/deskset can make PTT calls with each other or with the telephone base. Up to five pairs of PTT calls can be maintained at a time.
PTT to a single device
1. When the system is idle, press and hold the one-touch
EXT 1-0 key of the destination party. When the connection is made, both the caller and the destination party hear
1
PTT to:
1:Handset 1
Release PTT two beeps. The telephone base screen shows PTT to:
X:Handset X Release PTT key to stop ( X represents key to stop
1
PTT to: the extension number [ 1 0 ], Handset X represents the handset name) or PTT to: X:Deskset X Release PTT
1:Handset 1
-MUTE key to stop ( X represents the extension number [ 1 0 ],
Deskset X represents the deskset name).
2. Speak into the base speakerphone while continuing to hold down the onetouch EXT 1-0 key. Your voice is broadcast to the desired extension.
3. Release the one-touch EXT 1-0 key after speaking. There is a three-second
PTT wait state with -MUTE slowly flashing on the screen and the MUTE indicator flashing. During the PTT wait state, if necessary, you can press and hold the previous one-touch EXT
INT/PTT ALL
1-0 key or the INT/PTT ALL key to continue speaking into the base speakerphone.
4. The destination party can now respond (see Answer a PTT call in the
SynJ SB67108 handset manual or SynJ SB67148 deskset manual).
PTT to all devices
1. When the telephone base is idle, press and hold the INT/PTT ALL key to automatically activate the speakerphones of all the extensions. Both the caller and the destination parties hear two beeps.
2. Speak into the base speakerphone. Your voice is broadcast to all extensions. Release the INT/PTT ALL key after speaking. There is a threesecond PTT wait state with -MUTE slowly flashing on the screen and the
MUTE indicator flashing. During the PTT wait state, if necessary, you can press and hold the INT/PTT ALL key to continue speaking into the base speakerphone.
3. Any extension can reply. The first extension to reply will either convert the call into a normal intercom call with the caller or start a new PTT call. See Answer a
PTT call in the SynJ SB67108 handset manual or SynJ SB67148 deskset manual.
58
Telephone base operation
Push to talk (PTT) intercom
Answer a PTT call
1. When you hear two beeps, the screen displays PTT from: X:Handset X
( X represents the extension number [ 1 0 ], Handset X represents the handset name), or PTT from: X:Deskset X ( X represents the extension number [ 1 0 ], Deskset X represents the handset name).
2. Press INT to convert the call into a normal intercom call with that extension.
-OR-
Respond with a new PTT call. Wait for the end of the three-second PTT wait state (the screen changes to idle mode). To respond with the telephone base, see PTT to a single device or PTT to all devices on the previous page. To respond with a handset, see Answer a PTT call in the SynJ
SB67108 handset manual or SynJ SB67148 deskset manual.
NOTE: If the PTT call is sent to all handsets, an intercom call is established with the first person who presses INT .
Convert a PTT call to an intercom call
You can convert the PTT call to a two-way intercom call on the called telephone base.
1. Press INT on the called extension to convert the call to a two-way intercom call.
2. Optionally, put the corded handset on the telephone base or press
SPEAKER to end the intercom.
End a PTT call
• Press EXIT to end the incoming PTT call.
59
Directory
About the directory
Use the directory to store names and phone numbers. Directory entries are not shared with other extensions. Each handset has its own directory.
Capacity
The directory of this telephone base can store up to 100 entries, with a maximum of 16 alphanumeric characters (including spaces) for names and
32 digits for telephone numbers. A convenient search feature can help you quickly find and dial numbers (page 64).
If there are already 100 entries, the screen shows Memory is full . You cannot store a new number until you delete one. If you try to view the directory when there are no entries, the screen displays Directory empty .
Exit the directory
On the telephone base, press EXIT to cancel an operation and return to idle mode.
If you pause for too long while creating or reviewing an entry, the procedure times out and you have to begin again.
60
Directory
Create directory entries
Create a new directory entry
Use the following steps to store a name and number in the directory.
1.
When the telephone is idle, press MENU /ENTER twice to select Directory .
-OR-
Press DIR on the telephone base.
> Directory
Call log
Ringer setting
Mailbox setup
2. Press MENU/ ENTER to add an entry .
3. Enter the telephone number (up to 32 digits) using the dial pad when prompted.
•
•
•
•
Press REP or SKIP to move the cursor to the left or right.
Press REMOVE to backspace and delete a digit.
Press and hold REMOVE to erase all digits.
Press PAUSE /REDIAL dialing pause (a P appears) (page 62).
Directory empty
ENTER=Add
Enter phone #:
8887227702
ENTER=Next
• Press FLASH to enter a flash (page 62).
4. Press MENU/ ENTER to move on to the name. Enter the name when prompted.
• Use the dial pad to enter a name (up to 16 characters). Each time you press a key, the character on that key appears. Additional key presses produce other characters on that key. See the following chart.
Number key
1
9
0
*
#
6
7
8
4
5
2
3
1
& t w m p space
*
# g j a d u x n q
0 h k b e
2
‘ v y o r l i c f
Characters by number of key presses
3 4 5 6 7
( ) , .
A
D
G
J
M s
T z
B
E
H
K
N
P
U
W
C
I
F
L
O
Q
V
X
8
Y
6
R
4
5
2
3
8
/
S
Z
9
1
7
9
61
Directory
Create directory entries
- Press REP or SKIP to move the cursor to the left or right.
Enter name.:
CHRISTINE SMITH
- Press REMOVE to backspace and delete a character.
- Press and hold REMOVE to erase all characters.
ENTER=Save
- Press 0 once to add a space.
CHRISTINE SMITH
888 722 7702
5. Press MENU/ ENTER to save the setting and return to the previous menu. There is a confirmation tone. The name and the telephone number appear on the screen. To exit without making changes, press EXIT .
Store a pause in a directory number
Use this feature to include a pause in a number stored in the directory. You might need a pause in a directory number to enable access to automated telephone systems.
• When you wish to enter a pause in the dialing sequence, press PAUSE /REDIAL to store a 3.5 seconds pause. A P number. Each pause counts as one digit. If you want to save the number in the directory, press MENU/ ENTER .
Store a flash in a directory number
Use this feature to store the flash needed to access certain custom-calling services in a directory number.
• When you wish to enter a flash in the dialing sequence, press FLASH . An F appears in the
If you want to save the number in the directory, press MENU/ ENTER.
Enter phone #:
8887227702F
ENTER=Next
62
Directory
Review directory
Review directory entries
1.
When the telephone is idle:
Press MENU /ENTER twice to select Directory .
-OR-
Press DIR on the telephone base.
If there are no directory entries, the screen displays
Directory empty.
2. Press or to browse through the directory. Entries appear alphabetically by the first letter in the name.
Directory
4 entries
ENTER=Add
REMOVE=Delete all
Directory empty
ENTER=Add
CHRISTINE SMITH
888 722 7702
ENTER=Edit
63
Directory
Search directory
Search by name
Follow the steps to search for directory entries on the telephone base.
1.
When the telephone is idle, press MENU /ENTER twice to select Directory .
-OR-
Press DIR on the telephone base.
3. When a name appears, press the dial pad keys ( 2 9 ) to start a name search.
• The directory shows the first name beginning with the first letter associated with the dial pad key if there is an entry in the directory beginning with that letter.
If there is no entry matching the letter you press, it remains in the current entry.
4. To see other names starting with the letters on the same dial pad key, keep pressing the key. The names appear in alphabetical order.
For example, if you have the names Jennifer , Jessie , Kevin and Linda in your directory:
• If you press 5 (JKL) once, you see Jennifer .
If you press 5 (JKL) twice, you see Kevin .
If you press 5 (JKL) three times, you see Linda .
If you press 5 (JKL) four times, you see Jennifer .
• Jessie , press while Jennifer is displayed.
64
Directory
Dial, delete or edit entries
You can dial, delete or edit a directory entry (name and number) when it is shown on the telephone base screen. You can use the directory review or search (pages 63-64) to show an entry.
Display dial
When a number is displayed on the screen, you can dial the number by lifting the corded handset, pressing SPEAKER or LINE 1 LINE 4 for the desired line.
Delete an entry
When a directory entry appears, press REMOVE on the telephone base to delete the displayed entry from the directory. You cannot retrieve a deleted entry.
Delete all entries
1.
When the telephone is idle, press MENU /ENTER twice to select Directory .
-OR-
Press DIR on the telephone base.
2. Press REMOVE and the screen displays Delete entire directory? <=No >=Yes . Press SKIP to confirm or press REP to return to the previous screen.
Delete entire directory?
<=No >=Yes
NOTE: You cannot retrieve deleted entries.
Edit an entry
1. When a directory entry appears, press MENU/ ENTER .
2. Follow Steps 3 to 5 on pages 61-62.
NOTE: If the telephone number in the directory exceeds 16 digits,
< appears in front of the telephone number in the editing screen.
Press REP to move towards the beginning of the telephone number or press SKIP to move towards the end of the telephone number.
Enter phone #:
<888722770288872
ENTER=Next
65
Caller ID
About caller ID
This telephone supports caller ID services that most telephone service providers offer. Caller ID allows you to see the name, number, date and time of calls. Depending on your service subscription, you might see the caller’s number, or the caller’s name and number from the telephone service provider after the first or second ring. Caller ID information might not be available for every incoming call. Callers may intentionally block their names and/or telephone numbers.
This product can provide information only if both you and the caller are in areas offering caller ID service and if both telephone service providers use compatible equipment.
-----Line 1-----
CHRISTINE SMITH
888 722 7702
Information about caller ID with call waiting
Caller ID with call waiting lets you see the name and telephone number of the caller before answering the telephone, and while on another call.
There are fees associated with caller ID services. In addition, this service might be called by different names (such as caller ID with visual call waiting) by different telephone service providers and might not be available in all areas.
•
•
It might be necessary to change telephone service to use this feature.
Contact your telephone service provider if:
• You have both caller ID and call waiting, but as separate services (you might need to combine these services).
You only have caller ID service, or only call waiting service.
You do not subscribe to caller ID or call waiting services.
NOTES:
1.
2.
You can use this telephone with regular caller ID service, or you can use this telephone’s other features without subscribing to caller ID or caller ID combined with call waiting service.
The format of telephone numbers displayed depends on the home and local area codes you set
(See Area codes on page 21 for explanations and instructions on area code settings).
66
Caller ID
Caller ID Information
How the caller ID information (call log) works
The telephone stores caller ID information for the last 50 incoming calls in the telephone base. Entries are stored in reverse chronological order. The telephone deletes the oldest entry when the log is full to make room for new calls.
Each extension has independent caller ID information. Deleting the caller ID information on any one extension does not affect the caller ID information on other extensions.
If you answer a call before the information appears on the screen, it does not show in the caller ID information.
Review the caller ID information to determine who called, to easily return the call, or to copy the caller’s name and number into your directory.
*:Base
3 Missed calls
11:30PM 12/31
NEW CALL indicator turns on and XX Missed call(s) appears if there are new call log entries (including new or missed calls).
The time and date of the call and the caller’s name and telephone number are included in the display.
Caller ID information appears on the screen when the telephone rings, until the caller hangs up, the call has been answered at another extension, or the call ends.
If you subscribe to caller ID service, this phone automatically resets the time and date each time new call information is received. You can also set the time and date yourself (see Set date and time on page 22).
Caller’s name
Caller’s number
Time of call
CHRISTINE SMITH
888 722 7702
5:30PM 8/9 new
ENTER=Add
Date of call
Appears when the call is new or missed.
Add to directory
Screen display of the telephone base
NOTES:
1. The caller ID information might not be available for every incoming call. Callers might intentionally block their names and/or telephone numbers.
2. Each entry can store up to 32 digits for the telephone number and 16 characters for the name. If the telephone number has more than 16 digits but less than or equal to 24 digits, only the last
17 digits appear. If the telephone number has more than 24 digits, only the 8th to 24th digits
(17 digits) appear. In order to view the entire number, you must first save the entry to the directory
(see page 70). For instructions on viewing the digits, see page 68. If the telephone number has more than 32 digits, it is not saved or shown in the call log.
67
Caller ID
Caller ID operation
Memory match
If the incoming telephone number is an exact match with a telephone number in your directory, the name that appears on the screen matches the corresponding name in your directory.
For example, if Christine Smith calls, her name appears as Chris if this is how you entered it into your directory.
NOTE: The number you see on your caller ID is in the format from the telephone service provider. It usually delivers 10-digit telephone numbers (area code plus telephone number).
The telephone system ignores the area code when searching for a match and displays the name of the first corresponding number from the directory.
Missed (new) calls indicator
When the telephone base is in idle mode and has new or missed calls, its screen shows XX Missed call(s) .
All new or missed entries are counted as missed calls.
Each time you review a call log entry with the icon new , the number of missed calls decreases by one. When all the entries in the caller ID information become old (have been reviewed), the system removes the missed calls alert from the display, and the NEW CALL indicator turns off.
CHRISTINE SMITH
888 722 7702
5:30PM 8/9 new
ENTER=Add
*:Base
0 Missed calls
6:00PM 8/9
Review the caller ID information
1.
When the telephone is idle, press CALL LOG .
-OR-
When the telephone is idle, press MENU /ENTER.
Press or to scroll to Call log.
Press MENU/ ENTER.
2. Press or to review the caller ID information. The call log entries are stored in reverse chronological order starting with the most recent entry.
3. To exit without making changes, press EXIT .
Directory
> Call log
Ringer setting
Mailbox setup
68
Caller ID
Caller ID operation
View dialing options
Although the incoming call log entries have 10 digits (the area code plus the seven-digit number), in some areas, you may need to dial the seven digits only, 1 plus the seven digits, or 1 plus the area code plus the seven digits.
You can change and store the number of digits that you dial in the call log.
While reviewing the call log, press # (pound key) repeatedly on the telephone base to show different dialing options for local and long distance numbers before dialing or saving the telephone number in the directory.
CHRISTINE SMITH
888 722 7702
12:00PM 1/1
ENTER=Add
722 7702
1 722 7702
888 722 7702
1 888 722 7702
Press #
Dial a call log entry
1.
When in the call log, press or to browse the number you wish to call.
2.
Lift the handset or press SPEAKER .
-OR-
To override automatic line selection, press LINE 1 LINE 4 for the desired line, then lift the handset.
Delete entries
Delete a call log entry:
1.
When in the call log, press or to browse to the number you wish to delete.
2.
Press REMOVE to delete the shown entry from the caller ID history.
Delete all call log entries:
1.
When the telephone is idle, press CALL LOG .
-OR-
When the telephone is idle, press MENU /ENTER. Press
or to scroll to Call log. Press MENU/ ENTER.
2. Press REMOVE . The screen displays Delete all calls?
Press SKIP to clear all entries in the caller ID history or press REP to exit and leave all entries in the caller ID history intact.
3. To exit without making changes, press EXIT .
69
Call log
3 missed calls
REMOVE=Delete all
Delete all calls?
<=No >=Yes
Deleted
Caller ID
Caller ID operation
Save a call log entry to the directory
1.
When in the call log, press or to browse the desired number to save .
2.
The screen displays ENTER=Add. Press MENU/ ENTER.
3.
•
•
Press the dial pad keys to add digits (page 61).
Press REMOVE to erase a digit.
•
•
Press and hold REMOVE to erase all digits.
Press REP or SKIP to move the cursor to the left or right.
4. Press MENU/ ENTER to move to the name.
CHRISTINE SMITH
1 888 722 7702
12:00PM 1/1
ENTER=Add
Enter phone #:
18887227702
ENTER=Next
•
•
Press the dial pad keys to add characters (page 61).
Press REMOVE to erase a character.
•
•
Press and hold REMOVE to erase all characters.
Press REP or SKIP to move the cursor to the left or right.
Press 0 once to enter a space. •
5. Press MENU/ ENTER to save the new directory entry. There is a confirmation tone. The name and the telephone number appear.
Enter name:
CHRISTINE SMITH
ENTER=Save
CHRISTINE SMITH
1 888 722 7702
•
•
If the entry is already saved in the directory, the screen display remains the same and waits for more editing.
If there is no caller ID information, you hear an error tone. The number cannot be saved.
-OR-
To exit without making changes, press EXIT .
NOTE : You will need to change how a caller ID number is dialed if the entry does not appear in the correct format. Caller ID numbers might appear with an area code that is not necessary for local calls, or without a 1 that is necessary for long distance calls (see View dialing options on the previous page for more information).
70
Caller ID
Reasons for missing caller ID information
Reasons for missing caller ID information
There are also occasions when other information or no information shows for various reasons:
On-screen message
Private caller
Unknown caller
Reason
The caller prefers not to show the telephone number and name.
Your telephone service provider cannot determine the caller’s name and telephone number. Calls from other countries may also generate this message.
71
Answering system
Answering system and voicemail
Your telephone has separate indicators for two different types of voice messages: those left on its built-in answering system and those left at your service provider’s voicemail (fees may apply). Your telephone’s built-in answering system messages and voicemail messages are separate. Each alerts you to new messages differently. *: Base
0 Missed calls
2:43PM 1/13
COVM COVM
• If you turn on the COVM feature (See COVM on page 53 for more information) and the COVM icon displays on the base screen, your telephone service provider is indicating that it has new voicemail for you. To listen to your voicemail, dial an access number provided by your telephone service provider, followed by a security code or PIN.
• To listen to messages recorded on your digital answering system, press
(Messages) on the telephone base (page 78).
Some service providers bundle or combine multiple services like voicemail and call waiting, so you may not be aware that you have voicemail. To check what services you have and how to access them, contact your telephone service provider.
To use your voicemail service rather than the answering system, turn off the answering system. To use the answering system rather than the voicemail service, contact your telephone service provider to deactivate the voicemail service. Use your telephone answering system and voicemail together by setting your built-in answering system to answer before voicemail answers, as described below. To learn how to program your voicemail settings, contact your telephone service provider. Then, if you are on a call, or if the answering system is busy recording a message and you receive another call, the second caller can leave a voicemail message.
Set your answering system to answer calls at least two rings earlier than your voicemail is set to answer. For example, if your voicemail answers after six rings, set your answering system to answer after four rings. Some voicemail providers may program the delay before answering calls in seconds instead of rings. In this case, allow six seconds per ring when determining the appropriate setting.
72
Answering system
Setting your system to automatically answer calls
Use this feature to separately set each of the four lines to automatically answer incoming calls in three different ways.
General mailbox (gen MB only):
The called line rings on every extension for each incoming call. If there is no answer, the caller is prompted to leave a message in the general mailbox, which a person at any handset can review. The general mailbox stores incoming messages, memos, and two-way conversations (see Answering system operation on pages 78-82 for more information).
Auto attendant (auto att):
The called line for each incoming call flashes on every extension, but does not ring. Instead, the auto attendant answers. The caller can specify an extension or leave a general mailbox message. When the auto attendant directs a call to an extension but it is not answered, the auto attendant prompts the caller to leave a message for that extension or try another extension.
Each auto attendant can answer only one call at a time. You might want to turn on additional auto attendants in your system so that even when a call on one line is being answered, a second auto attendant can answer another ringing line. You can designate up to four auto attendants in your system
(see Auto attendant operation on pages 75-77 for more information.)
Announce only (annc only):
The called line for each incoming call flashes and rings on every extension.
After the number of rings you programmed (see Number of rings on page 32), the answering system plays an announcement only and then the call is dropped automatically. The caller is not allowed to specify an extension or leave a message in the general mailbox. You can use a default outgoing announcement or record up to five announcements of your own.
No answer:
You can disable automatic answering on any of the telephone lines.
An example of a 2-line answering system setup
If you have two phone lines and two or more extensions and you wish to use the auto attendant, then configure both lines to use the auto attendant.
Then, if a call comes in while one line is busy, it will still be answered by the auto attendant.
Line 1: Auto attendant (2 rings)
Line 2: Auto attendant (2 rings)
73
Answering system
Setting your system to automatically answer calls
An example of a 4-line answering system setup
If you have four phone lines and many extensions, you can set up the auto attendant to answer up to three simultaneous calls. You can set up the fourth line to ring as a private direct line to a single extension by excluding all others in the Ring group (page 17).
Line 1: Auto attendant (2 rings)
Line 2: Auto attendant (2 rings)
Line 3: Auto attendant (2 rings)
Line 4: General mailbox (4 rings, all but one extension excluded)
Select the answer mode
1.
When the telephone is idle, press ANSWER ON for the desired line.
2.
Press or to scroll to the desired answer mode
( Ans->Gen MB only , Ans->Auto att , Ans->Annc only or
No answer ). Press MENU/ ENTER to select the mode. To exit without making changes, press EXIT .
>
Ans->Gen MB only
Ans->Auto att
Ans->Annc only
No answer
Answering system capacity
You can record up to five new announcements to have different announcements for each line. Each announcement can be up to two minutes.
The announcements of auto attendant, general mailbox and announce only answer mode all require system memory to record, so we suggest recording brief announcements in order to leave more space for messages.
The maximum recording time of all handsets and base is 180 minutes.
The actual recording time depends on individual message characteristics.
Individual messages can be up to three minutes. Messages remain available for review until you delete them.
If the system memory is full, the screen displays Message full , and you cannot record new messages until old ones have been deleted. Check remaining system space frequently to maintain availability of space for incoming messages.
NOTE: You cannot record an announcement when the telephone system is out of space.
You will hear a two-beep alert tone and voice prompt “ Memory is full.
” Please refer to
Remaining space on page 38.
74
Answering system
Auto attendant operation
Turn the auto attendant on
1.
When the telephone is idle, press ANSWER ON for the desired line to set up.
2.
Press or to scroll to Ans->Auto att .
3.
Press MENU/ ENTER to turn on the auto attendant. The current auto attendant announcement plays. The screen displays Auto Attendant
ON Play announcement with voice prompt “Hello, this is automatic attendant ,” and then the idle screen appears.
-OR-
Press or to scroll to No answer to turn the auto attendant off. Press
MENU/ ENTER to turn off the auto attendant feature for that line.
To exit without making changes, press EXIT .
1.
2.
3.
NOTES:
The auto attendant only answers outside calls.
The auto attendant does not answer calls when that line is in use.
You can press VOL+ or VOL to adjust the announcement playback volume.
Using the auto attendant
When you set a line to be an auto attendant, it automatically picks up the ringing line after the number of rings you programmed (see Number of rings on page 31), and plays your selected auto attendant announcement.
*:Base
3 Missed calls
11:30PM 12/31
AuAt
While the line silently rings, and while the auto attendant is answering and directing a call, the line indicator flashes (page 44). To interrupt the auto attendant, press the flashing line indicator LINE 1 LINE 4 on the telephone base or L 1 L 4 on a cordless handset to talk to the caller on that line. You can also allow the auto attendant to answer the incoming call while you make a new call on another line.
When a caller enters a correct extension number, the auto attendant transfers the call to that extension and announces to the caller, “Please wait.” If the called extension does not answer, the caller is prompted to try another extension or leave a message in a private mailbox for the last attempted extension. The auto attendant attempts to transfer the call up to five times.
75
Answering system
Auto attendant operation
If the caller enters an extension number plus the # (pound key) after hearing the announcement , the auto attendant transfers the call to the specified extension. If the call is not picked up after five rings, the caller hears “No one is available to answer the call. To leave a message, press 1.
To call another extension, press 2. To call the operator, press star,” and waits five seconds for another entry from the caller. If the caller still hasn’t entered an extension number after hearing this message three times, the auto attendant forwards the call to the general mailbox to leave a message.
If the caller enters an invalid extension number , the auto attendant announces, “Please wait. This number is not assigned. To leave a message, press 1. To call another extension, press 2. To call the operator, press star.”
If the caller enters the (star key) plus the # (pound key) , the auto attendant announces ”Calling the operator,” and then transfers the call to the telephone base.
If the caller enters the remote access code while hearing the announcement , the auto attendant stops playing the announcement and the caller can remotely access the general mailbox (See Remote access on page 83 for information).
If the caller does not enter any number after hearing the announcement, the auto attendant announces three times “Hello, this is auto attendant.
Please enter your party’s extension, followed by pound (#). If you are using a rotary telephone, please stay on the line. For a company directory, dial star twice.” Then, the auto attendant transfers the call to the general mailbox for the caller to leave a message.
Using multiple auto attendants
Use this feature to set one or more telephone lines to act as auto attendants when the primary auto attendant is turned off or busy.
•
•
An auto attendant is busy when someone at that extension is doing any of the following:
• dialing from the directory or call history
*:Base
0 Missed call
08:00AM 12/30
AuAt AuAt using any of the lines to make or answer a call when the answering system is recording a message at that extension
You can choose a particular telephone line to always be the primary auto attendant by setting that line to have the shortest auto attendant pickup delay
(number of rings) and setting the other auto attendants to have longer pickup delays (more rings). If the auto attendant pickup delays are the same, incoming calls are distributed randomly to the auto attendants.
76
Answering system
Auto attendant operation
Auto attendant flow chart
Incoming call
AA answers and plays outgoing announcement
Caller dials
* and #
AA sends call to the telephone base
Caller dials extension number and #
Caller dials remote access code
No caller input
AA calls extension
Person answers call?
No
Caller enters another extension or records a message
Yes
Answering system remote access
Normal call
General mailbox records message
77
Answering system
Answering system operation
Set general delivery mailbox to answer
1.
When the telephone is idle, press ANSWER ON for the desired line.
2.
Press or to scroll to Ans->Gen MB only .
3.
Press MENU/ ENTER . The ANSWER ON indicator turns on.
The current mailbox announcement plays. The screen displays General Mbox ON Play announcement , and then it returns to the idle screen.
-OR-
To exit without making changes, press EXIT .
> Ans->Gen MB only
Ans->Auto att
Ans->Annc only
No answer
General Mbox ON
Play announcement
00:09
NOTE: While previewing the announcement, you can adjust the volume by pressing VOL+ or
VOL. If you do not want to hear the announcement, press EXIT .
Incoming messages
This telephone also accepts COVM recorded by your telephone service provider which you subscribe to for voicemail service (page 53).
New message indication
The (Messages) indicator on the telephone base flashes when there are new or missed messages and memos in the general mailbox.
Message playback
From the telephone base, you can play the messages in both the general mailbox and handset/deskset mailboxes.
If you have new messages, you hear only the new messages (in chronological order). If there are no new messages, the system plays back all the messages (in chronological order).
When playback begins, the total number of messages is announced. Before each message, you hear the date and time of the recording. After the last message, you hear “ End of the messages.
”
To listen to messages in the general mailbox:
1. While the telephone is idle, press (Messages) on the telephone base.
2. The system announces the number of new or missed messages in the general mailbox.
78
Answering system
Answering system operation
3. Press MENU/ ENTER to select Play all to listen to all messages. Press REP to repeat the current message; press REP twice to listen to the previous message. Press
SKIP to move to the next message. You hear two beeps at the end of each message playback.
2 New messages
Deliver
Delete all old
4. Playback ends after playing all the messages, and then returns to the previous menu.
5. Press ( Messages) again to end the message playback at any time.
12:57 PM 03/06
<= Message 1 =>
To listen to messages in the handset/deskset mailbox:
1.
When the telephone is idle, press (Messages) on the telephone base.
2.
Press the one-touch EXT 1-0 key for the destination extension mailbox.
3.
Use the dial pad to enter the four-digit remote access code of the extension. Use REMOVE to backspace and delete a digit. Then, press MENU/ ENTER .
1 New messages
Deliver
Handset anncemnt
4.
Go to Steps 2-5 in the To listen to messages in the general mailbox section on the previous page.
•
•
•
•
•
Options during playback
When a message is playing, you can adjust the playback volume, skip, repeat, or delete the message.
When a message is playing on the telephone base:
• Lift the corded handset to listen to the message playback through the handset earpiece. Press SPEAKER to switch back to speakerphone.
Press VOL+ or VOL to adjust the message playback volume.
Press SKIP to skip to the next message.
Press REP to repeat the current message. Press twice to hear the previous message.
Press REMOVE to delete the message. The system announces “ Message deleted.
”
Press (Messages) to stop playback.
Delete all old messages
Use this feature to only delete old (reviewed) messages. You cannot delete new messages until you review them. You cannot retrieve deleted messages.
Delete all old messages in the general mailbox:
1. When the telephone is idle, press telephone base.
(Messages) on the
2 New messages
Play all
Deliver
79
Answering system
Answering system operation
2. Press or to scroll to Delete all old. Press MENU/ ENTER.
3. The screen displays Delete all old messages? <=No >=Yes .
Press REP to cancel this operation to return to the previous menu, or press SKIP to remove all old messages from the general mailbox.
Delete all old messages?
<=No >=Yes
All deleted
Delete all old messages in the handset/deskset mailbox:
1.
When the telephone is idle, press (Messages) on the telephone base.
2.
Press the one-touch EXT 1-0 key for the destination extension mailbox.
3.
Use the dial pad to enter the four-digit remote access code of the extension.
Use REMOVE to backspace and delete a digit. Then, press MENU/ ENTER .
4.
Press or to scroll to Delete all old. Press MENU/ ENTER.
5.
The screen displays Delete all old messages? <=No >=Yes .
Press REP to cancel this operation to return to the previous menu, or press SKIP to remove all old messages from the handset mailbox.
3 New messages
To general MBox
Fast answer mode
NOTE: If there are any new or missed messages in the general mailbox, the
(Messages) indicator still flashes after you delete all old messages.
Transfer message
When a message is playing in the general mailbox or handset mailbox, you can transfer the message to a single extension, all extensions or the telephone base.
When a message is playing on the telephone base:
1. Press XFER on the telephone base.
2. Press or to scroll to an extension, all extensions or the telephone base, then press MENU/ ENTER .
-OR-
Press the one-touch EXT 1-0 key on the telephone base. The message is automatically transferred to the desired extension.
A copy of the message automatically transfers to the desired extension, all extensions or the telephone base. The general mailbox retains the original copy of the message.
80
Answering system
Answering system operation
Record and deliver memos
Memos are messages you record into the general mailbox or handset mailbox at the telephone base. You can save, play back, and delete them like incoming messages. You can record a memo as a reminder to yourself, or send a message to other extensions using the answering system.
To record a memo in the general mailbox, then deliver it:
1. When the telephone is idle, press (Messages) on the telephone base.
2. Press or to scroll to Deliver .
Press MENU/ ENTER.
3. Press or to scroll to select the telephone base or a desired registered extension, or select all the registered extensions.
4. Press MENU/ ENTER . The system announces “ Record after the tone. Press stop when you are done .” There is a reminder beep. The timer starts counting.
Lift the corded handset or face the telephone to record your memo.
5. Press MENU/ ENTER again to stop recording. The timer stops and the recorded memo automatically plays back.
The screen displays 1=Change 2=OK .
6. Press 1 to record that memo again.
-OR-
Press 2 to save the memo and send it to the extension you selected. The system announces “ Message transferred to mailbox X, ” and then returns to the previous menu or memo.
2 New messages
Play all
Delete all old
>
*:Base
1:Handset 1
2:Handset 2
#:All
Record message
ENTER=Start
Record message
00:32
ENTER=Stop
Play message
00:09
1=Change 2=OK
Msg. transferred to mailbox
2
To record a memo in the handset/deskset mailbox, then deliver it:
1.
When the telephone is idle, press (Messages) on the telephone base.
2.
Press the one-touch EXT 1-0 key for the destination extension mailbox.
3.
Use the dial pad to enter the four-digit remote access code of the extension. Use REMOVE to backspace and delete a digit. Then, press MENU/ ENTER .
2 New messages
Play all
4.
Go to Steps 2-6 in To record a memo in the general mailbox, then deliver it above on this page.
Handset anncemnt
81
Answering system
Answering system operation
Play back a memo
Play memos the same way as normal messages (see Message playback on page 78).
Set answering system to play announcement only
1.
When the telephone is idle, press ANSWER ON for the desired line.
2.
Press MENU/ ENTER . The current Announce only announcement plays. The screen displays Annc only ON
Play announcement , and then it returns to the idle screen.
-OR-
Ans->Gen MB only
Ans->Auto att
> Ans->Annc only
No answer
Annc only ON
Play announcement
00:04
To exit without making changes, press EXIT .
*:Base
3 Missed calls
11:30PM 12/31
Annc
NOTES:
1. The default announcement is “Hello. No one is available to answer your call. Thank you for calling.”
2. While previewing the announcement, you can adjust the volume by pressing VOL+ or VOL. If you do not want to hear the announcement, press EXIT .
Set general delivery mailbox to not answer
1.
When the telephone is idle, press ANSWER ON for the desired line.
2.
Press or to scroll to No answer . Press MENU/ ENTER .
Disable the answering system
1.
When the telephone is idle, press ANSWER ON for the desired line to disable.
2.
Press or to scroll to No answer . Press
MENU/ ENTER to prevent the answering machine from answering calls on that line.
-OR-
To exit without making changes, press EXIT .
82
Answering system
Remote access
Use this feature to reach your answering system remotely by dialing your telephone number from any touch-tone telephone.
To remotely reach the answering system:
1. Dial your telephone number from any touch-tone telephone.
2. When the system answers, enter the four-digit remote access code ( 0000 is the default code; see page 34 to change it).
The system automatically announces the number of messages (new and/or old) if there are any, and then begins to play them.
3. You can also enter the following remote commands.
Remote commands:
1 Press to play to all messages.
3 Press to delete the current message (during playback).
Press to repeat the current message (during playback).
4
After you hear “Repeat” and within five seconds, press 4 again to listen to the previous message (during playback).
5
Press to stop and return to the remote commands (during playback).
6 Press to skip to the next message (during playback).
7 Press to transfer the current message (during playback).
Press to end the call.
4. Hang up to end the call and save all messages that have not been deleted.
Cut out the remote access wallet card at the back of this user’s manual for quick reference.
NOTES:
1. If you do not enter a valid remote access code, the answering system answers the call as usual and all the voice and digits entered will be recorded as messages stored in your general mailbox.
2. If you do not enter any remote access code, the answering system announces “ Thank you for calling, ” and the call ends.
3. When there is no new message or all the new messages are played during remote access, you hear a help menu listing all features and commands. If there is no command after the help menu is played three times, the call ends automatically.
83
Answering system
Remote access
4. If the memory is full, you hear a two-beep alert tone and the answering system announces,
“Memory is full.” The telephone base screen displays Message full .
and you cannot record new messages until old ones have been deleted. Check the system remaining space (page 38) frequently to maintain availability of space for incoming messages.
5. If you press 4 within five seconds of each message playback start, the previous message plays instead of repeating the current message.
84
Cordless headset
Cordless headset operation
The AT&T compatible DECT 6.0 cordless headset (AT&T model
TL7600) functions as an extension of the telephone base.
The cordless headset cannot be used for PTT calls. It cannot initiate an intercom call, but can receive one if it is called by the telephone base, a handset or a deskset.
To register and deregister a TL7600 headset to the SynJ
SB67158 telephone base, please refer to pages 12-13. To view the TL7600 manual, visit our website at www.telephones.att.com
, or call 1 (888) 915-2007 .
In Canada, dial 1 (866) 288-4268 .
Cordless headset extension number
The cordless headset is always assigned extension number 0 regardless of how many handsets are registered.
By pressing the ON /OFF button on the cordless headset, you can see the extension 0 icon on the telephone base screen.
Line1
0
00:00:05
Switch between corded or cordless handset, telephone speakerphone and cordless headset
Use the following instructions to switch between the telephone base components (corded handset, speakerphone, corded headset and cordless headset). You must use the intercom system (page 54) to switch between the base and the cordless handsets.
To switch from corded handset, corded headset, or speakerphone to cordless headset:
During a call, press the ON /OFF button on the cordless headset.
To switch from cordless headset to corded handset, corded headset, or speakerphone:
During a call, lift the corded handset, or press HEADSET , or press SPEAKER on the telephone base.
85
Appendix
Telephone base display screen messages
All deleted
All devices deregistered
Aux In Device
Playing
Auto Attendant ON
Play announcement
All old messages in the general mailbox are erased.
The cordless handsets, desksets and cordless headset deregistration was successful.
Audio device connected with the telephone base is playing for
M.O.H. review.
Auto attendant is on and the selected announcement plays.
Busy
Call restricted
Failed intercom or conference call (there are already two cordless handsets being used).
Your extension is in the restricted extension list and you are trying to dial a number that starts with the restricted prefix.
The alert call number is dialing out. Calling alert #
Calling
X:Deskset X
Calling
X:Handset X
Call log empty
The telephone base is starting an intercom call with a deskset.
The telephone base is starting an intercom call with a cordless handset.
There are no entries in the caller ID history.
Cordless headset registered
COVM reset
The cordless headset registration was successful.
COVM feature is reset.
Deleted A call log entry, a redial number or a directory entry was deleted.
Deregister all?
Deregistering
All registered devices will be deregistered from the telephone base.
The telephone system is deregistering a device from the telephone base.
Deskset registered The deskset registration was successful.
Audio device connected to the AUX IN jack at the base is for music on hold feature.
Device connected to the headset jack will be used for M.O.H.
Directory empty There are no directory entries.
There is no directory entry when you press DIR for chain dialing. Directory
No items stored
Ended
General Mbox ON
Play announcement
You have just ended a call.
General mailbox is on and the selected announcement plays back.
86
Appendix
Telephone base display screen messages
Handset registered The cordless handset registration was successful.
------Line X------
Incoming call
There is an incoming call.
Intercom to:
Line X
You have started the intercom process, and need to enter the number of the handset you wish to call.
The telephone line X is in use.
Memory is full
Message full
The directory is full. You cannot save new entries unless you delete some current entries.
The system memory is full. You cannot record new messages unless you delete some old messages.
A message is transferring from the general mailbox to a particular private mailbox.
Msg. transferred to mailbox X
No Device is connected to the headset jack at base
No device registered
No items stored
There is no audio device connected to the AUX IN jack at the telephone base.
There are no handsets or headsets registered to the base to deregister.
The redial list is empty.
M.O.H. currently in use. Please try again later.
You cannot record or playback music on the telephone base while a call is listening to the current hold music.
Please enter another access code.
The access code you are trying to save already exists in the system.
You are trying to confirm the alert number or set the notify alert on or off before you set the alert number.
Please set the alert #
Press SPKR to confirm the alert call
Press the telephone base speakerphone key to call the alert call number.
PTT To:
X:Deskset X
Release PTT key to stop
You are using push to talk (PTT) intercom to call Deskset X .
Release the one-touch EXT 1-0 to complete a one-way conversation.
87
Appendix
Telephone base display screen messages
PTT To:
X:Handset X
Release PTT key to stop
Recorded M.O.H.
reconnect. Aux In
Device reset source.
You are using push to talk (PTT) intercom to call Handset X .
Release the one-touch EXT 1-0 to complete a one-way conversation.
Unplug the audio device from the AUX IN jack at the telephone base while the M.O.H. source is set to Aux In Device .
Registering new device...
Registration failed
A cordless handset, a cordless headset, a deskset or a repeater is registering to the telephone base.
The handset or headset registration failed.
Sorry, this mailbox is being used.
You cannot access a mailbox that is being used.
Speed dial X
No number
You cannot initiate a speed dial without a telephone number stored in that speed dial location.
The system is busy.
Please try again later.
The system resources are all occupied.
You cannot transfer a message to the telephone base general mailbox.
This is your mailbox.
To use headset, turn off M.O.H.
or reset source.
You cannot use a corded headset while the M.O.H. source is from an audio device.
You should change the M.O.H. source setting before using a corded headset.
You cannot access a private mailbox in use. You should try again later.
Users in mailbox.
Please try again later.
Transfer to:
(For systems with two or more handsets/desksets)
XX Missed calls
You have started the intercom process and need to enter the number of the handset or desksets you wish to call.
There are new calls in the caller ID history.
88
Appendix
Maintenance
Taking care of your telephone
•
•
•
•
Your telephone base contains sophisticated electronic parts, so you must treat it with care.
Avoid rough treatment.
Place the corded handset down gently.
Save the original packing materials to protect your telephone base if you ever need to ship it.
Avoid water
• You can damage your telephone base if it gets wet. Do not use the corded handset in the rain, or handle it with wet hands. Do not install the telephone base near a sink, bathtub or shower.
Electrical storms
• Electrical storms can sometimes cause power surges harmful to electronic equipment. For your own safety, take caution when using electric appliances during storms.
Cleaning your telephone
• Your telephone base has a durable plastic casing that should retain its luster for many years.
Clean it only with a soft cloth slightly dampened with water or a mild soap.
• Do not use excess water or cleaning solvents of any kind.
Remember that electrical appliances can cause serious injury if used when you are wet or standing in water. If the telephone base should fall into water, DO NOT RETRIEVE IT UNTIL
YOU UNPLUG THE POWER CORD AND TELEPHONE LINE CORDS FROM THE WALL. Pull the unit out by the unplugged cords.
89
Appendix
Important safety information
This symbol is to alert you to important operating or servicing instructions that may appear in this user’s manual. Always follow basic safety precautions when using this product to reduce the risk of injury, fire, or electric shock.
Safety information
• Read and understand all instructions in the user’s manual. Observe all markings on the product.
• Avoid using a telephone during a thunderstorm. There may be a slight chance of electric shock from lightning.
• Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain circumstances, a spark may be created when the adapter is plugged into the power outlet, or when the handset is replaced in its cradle. This is a common event associated with the closing of any electrical circuit. The user should not plug the phone into a power outlet, and should not put a charged handset into the cradle, if the phone is located in an environment containing concentrations of flammable or flame-supporting gases, unless there is adequate ventilation. A spark in such an environment could create a fire or explosion. Such environments might include: medical use of oxygen without adequate ventilation; industrial gases (cleaning solvents; gasoline vapors; etc.); a leak of natural gas; etc.
• Do not use this product near water, or when you are wet. For example, do not use it in a wet basement or shower, or next to a swimming pool, bathtub, kitchen sink, or laundry tub. Do not use liquids or aerosol sprays for cleaning. If the product comes in contact with any liquid, unplug any line or power cord immediately. Do not plug the product back in until it has dried thoroughly.
• Install this product in a protected location where no one can trip over any line or power cords.
Protect cords from damage or abrasion.
• If this product does not operate normally, see the Troubleshooting section on pages 99-105 of this user’s manual. If you cannot solve the problem, or if the product is damaged, refer to the Limited warranty section on pages 96-97. Do not open this product except as directed in your user’s manual. Opening the product or reassembling it incorrectly may expose you to hazardous voltages or other risks.
• Replace backup battery only as described in your user’s manual (see page 9). Do not burn or puncture batteries — they contain caustic chemicals.
• This power adapter is intended to be correctly oriented in a vertical or floor mount position.
The prongs are not designed to hold the plug in place if it is plugged into a ceiling, an underthe-table or cabinet outlet.
Caution: Use only the power adapter provided with this product. To obtain a replacement, visit our website at www.telephones.att.com
or call
1 (888) 915-2007
. In Canada, dial
1 (866) 288-4268
.
90
Appendix
Important safety information
Especially about cordless telephones
• Electrical power: The telephone base must be connected to a working electrical outlet. The electrical outlet should not be controlled by a wall switch. Calls cannot be made from the handset if the telephone base is unplugged, switched off or if the electrical power is interrupted.
• Power adapter: The power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless telephones):
Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless telephones and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:
Pacemaker patients
• Should keep wireless telephones at least six inches from the pacemaker.
• Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket, when it is turned ON.
• Should use the wireless telephone at the ear opposite the pacemaker.
WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless telephones.
Especially about telephone answering systems
Two-way recording: This unit does not sound warning beeps to inform the other party that the call is being recorded. To ensure that you are in compliance with any federal or state regulations regarding recording a telephone call, you should start the recording process and then inform the other party that you are recording the conversation.
SAVE THESE INSTRUCTIONS
91
Appendix
For C-UL compliance
In compliance with the bilingual requirements for safety, caution, and warning markings of
Canadian Federal and Provincial/Territorial statutes and regulations, the French version of
Important safety information is included.
Mesures de sécurité importantes
Ce symbole vous alertera d’informations importantes ou d’instructions d’entretien pouvant apparaître dans ce guide d’utilisation. Respectez toujours les mesures de sécurité et de sécurité de base lorsque vous utilisez ce produit, afin de réduire les risques de blessures, d’incendie, ou d’électrocution.
Information relative à la sécurité
• Veuillez lire et comprendre toutes les instructions de ce guide d’utilisation. Relectez toutes les inscriptions apparaissant sur le produit.
• Évitez d’utiliser le téléphone pendant un orage. Il pourrait y avoir un faible risque d’électrocution.
• N’utilisez pas un téléphone près d’une fuite de gaz. Dans certaines circonstances, une flammèche pourrait se produire lorsque l’adaptateur est branché à une prise de courant, ou lorsque le combiné est déposé sur son chargeur. Ceci est un événement fréquent associé avec la fermeture d’un circuit électrique. L’utilisateur ne devrait pas brancher un téléphone dans une prise de courant, et ne devrait pas déposer un combiné chargé dans le chargeur, si le téléphone se trouve dans un environnement comportant une concentration de gaz inflammables ou ignifuges, à moins de se trouver dans un endroit où la ventilation est adéquate. Une flammèche dans de tels environnements pourrait provoquer une explosion.
De tels environnements peuvent comprendre : les endroits où de l’oxygène à des fins médicales est utilisé sans ventilation adéquate; des endroits où se trouvent des gaz industriels
(dissolvants de nettoyage, des vapeurs de gazoline, etc.), une fuite de gaz naturel, etc.
• N’utilisez pas ce produit près de l’eau ou lorsque vous êtes mouillés. Par exemple, ne l’utilisez pas dans des sous-sols humides ou sous la douche, ou près d’une piscine, d’un bain, d’un évier de cuisine, ou d’une cuve de lavage. N’utilisez pas de liquides, ou de vaporisateurs aérosol de nettoyage. Si le produit entre en contact avec du liquide, débranchez immédiatement le fil téléphonique ou le cordon d’alimentation. Ne rebranchez pas le produit avant qu’il soit complètement sec.
• Installez cet appareil dans un endroit protégé où personne ne peut trébucher sur les cordons d’alimentation ou la ligne téléphonique. Protégez les câbles contre les dommages ou l’abrasion.
• Si le produit ne fonctionne pas correctement, consultez la section Dépannage
( Troubleshooting ) des pages 99-105 de ce guide d’utilisation. Si vous ne pouvez pas régler le problème, ou si le produit est endommagé, consultez la section Garantie limitée ( Limited warranty ) des pages 96-97. N’ouvrez pas ce produit, sauf tel qu’indiqué dans le guide d’utilisation. L’ouverture du produit ou le remontage inadéquat pourrait vous exposer à des tensions dangereuses ou autres dangers.
• Remplacez les piles uniquement tel que décrit dans votre guide d’utilisation (page 9).
N’incinérez pas et ne percez pas les piles — elles contiennent des produits chimiques caustiques.
• L’adaptateur de courant est conçu pour être orienté verticalement ou installé sur le plancher.
Les broches ne sont pas conçues pour se maintenir en place si la fiche est branchée dans une prise de courant au plafond, sous la table ou sous une armoire.
MISE EN GARDE: N’utilisez seulement l’adaptateur inclus avec ce produit. Pour obtenir une pièce de rechange, visitez notre site Web au www.telephones.att.com
ou composez le
1 (888) 915-2007
. Au Canada, composez le
1 (866) 288-4268
.
92
Appendix
For C-UL compliance
Spécifiquement en rapport avec les téléphones sans fil
• Alimentation électrique : La base de ce téléphone sans fil doit être branchée à une prise de courant électrique fonctionnelle. La prise électrique ne doit pas être contrôlée par un interrupteur mural. Les appels ne peuvent pas être effectués à partir du socle du téléphone n’est pas branchée, si elle est hors fonction ou si le courant électrique est coupé.
• L’adaptateur de courant : L’adaptateur de courant est conçu pour être orienté verticalement ou installé sur le plancher. Les broches ne sont pas conçues pour se maintenir en place si la fiche est branchée dans une prise de courant au plafond, sous la table ou sous une armoire.
Mesures préventives pour les utilisateurs de stimulateurs cardiaques implantés dans l’organisme
Stimulateurs cardiaques (ne s’applique qu’aux téléphones sans fil numériques) :
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche indépendante, a mené une évaluation pluridisciplinaire des interférences entre les téléphones sans fil portatifs et les stimulateurs cardiaques implantés dans l’organisme. Appuyée par l’Administration des aliments et drogues (FDA) des États-unis, la firme WTR recommande aux médecins :
Avis aux détenteurs de stimulateurs cardiaques
• Ils doivent tenir le téléphone sans fil à une distance d’au moins six pouces du stimulateur cardiaque.
•
•
Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en fonction.
Ils doivent utiliser le téléphone sans fil en l’appuyant sur l’oreille qui se trouve dans la direction opposée au stimulateur cardiaque.
L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs de simulateurs cardiaques causé par les gens qui utilisent un téléphone sans fil à proximité de ceux-ci.
Spécifiquement en rapport avec les répondeurs téléphoniques
Enregistrement deux voies : Cet appareil n’émet pas de bips d’avertissement qui permettent de prévenir l’autre partie que vous enregistrez la conversation. Pour assurer votre conformité aux règlements fédéraux ou provinciaux en rapport avec les enregistrements des conversations téléphoniques, vous devriez informer l’autre partie lorsque vous activez l’enregistrement.
CONSERVEZ CES INSTRUCTIONS
93
Appendix
FCC part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment contains, among other things, a product identifier in the format US:
AAAEQ##TXXXX. This identifier must be provided to your telephone service provider upon request.
The plug and jack used to connect this equipment to premises wiring and the telephone network must comply with the applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines. See Installation Instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th and 7th characters following the US: in the product identifier (e.g., if ## is
03, the REN is 0.3). In most, but not all areas, the sum of all RENs should be five (5.0) or less. For more information, please contact your telephone service provider.
This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment connected to telephone line, ensure the connection of this equipment does not disable your alarm equipment. If you have questions about what will disable the alarm equipment, consult your telephone service provider or a qualified installer.
If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents. For repair procedures, follow the instructions outlined under the Limited
Warranty.
If this equipment is causing harm to the telephone network, the telephone service provider may temporarily discontinue your telephone service. The telephone service provider is required to notify you before interrupting service. If advance notice is not practical, you will be notified as soon as possible. You will be given the opportunity to correct the problem and the telephone service provider is required to inform you of your right to file a complaint with the FCC. Your telephone service provider may make changes in its facilities, equipment, operation, or procedures that could affect the proper functioning of this product. The telephone service provider is required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please:
Remain on the line and briefly explain the reason for the call before hanging up.
Perform such activities in off-peak hours, such as early morning or late evening.
Industry Canada
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Privacy of communications may not be ensured when using this telephone.
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed five.
This product meets the applicable Industry Canada technical specifications.
94
Appendix
FCC part 15
•
•
•
This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Privacy of communications may not be ensured when using this telephone.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The handset may be safely held against the ear of the user. The telephone base shall be installed and used such that parts of the user’s body other than the hands are maintained at a distance of approximately 20 cm (8 inches) or more. If you choose to use a clipping device, please make sure to only use the supplied AT&T belt clip.
This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B).
95
Appendix
Limited warranty
The AT&T brand is used under license - any repair, replacement or warranty service, and all questions about this product should be directed to: In the United States of America, visit www.telephones.att.com
or call
1 (888) 915-2007
. In Canada, call
1 (866) 288-4268
.
1. What does this limited warranty cover?
The manufacturer of this AT&T branded product warrants to the holder of a valid proof of purchase (“CONSUMER” or “you”) that the product and all accessories provided in the sales package (“PRODUCT”) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the
PRODUCT operating instructions. This limited warranty extends only to the CONSUMER for products purchased and used in the United States of America and Canada.
2. What will be done if the PRODUCT is not free from defects in materials and workmanship during the limited warranty period (“materially defective PRODUCT”)?
During the limited warranty period, the manufacturer’s authorized service representative will repair or replace at the manufacturer’s option, without charge, a materially defective PRODUCT.
If the manufacturer repairs the PRODUCT, they may use new or refurbished replacement parts. If the manufacturer chooses to replace the PRODUCT, they may replace it with a new or refurbished
PRODUCT of the same or similar design. The manufacturer will retain defective parts, modules, or equipment. Repair or replacement of the PRODUCT, at the manufacturer’s option, is your exclusive remedy. The manufacturer will return repaired or replacement products to you in working condition. You should expect the repair or replacement to take approximately 30 days.
3. How long is the limited warranty period?
The limited warranty period for the PRODUCT extends for TWO (2) YEARS from the date of purchase. If the manufacturer repairs or replaces a materially defective PRODUCT under the terms of this limited warranty, this limited warranty also applies to repaired or replacement PRODUCT for a period of either (a) 90 days from the date the repaired or replacement PRODUCT is shipped to you or (b) the time remaining on the original two-year limited warranty; whichever is longer.
4. What is not covered by this limited warranty?
•
•
•
•
This limited warranty does not cover:
• PRODUCT that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water, or other liquid intrusion; or
• PRODUCT that has been damaged due to repair, alteration, or modification by anyone other than an authorized service representative of the manufacturer; or
• PRODUCT to the extent that the problem experienced is caused by signal conditions, network reliability or cable or antenna systems; or
PRODUCT to the extent that the problem is caused by use with non-AT&T accessories; or
PRODUCT whose warranty/quality stickers, PRODUCT serial number plates or electronic serial numbers have been removed, altered or rendered illegible; or
• PRODUCT purchased, used, serviced, or shipped for repair from outside the United States of
America or Canada, or used for commercial or institutional purposes (including but not limited to products used for rental purposes); or
PRODUCT returned without a valid proof of purchase (see item 6); or
Charges for installation or setup, adjustment of customer controls, and installation or repair of systems outside the unit.
96
Appendix
Limited warranty
5. How do you get warranty service?
To obtain warranty service in the United States of America, visit www.telephones.att.com
or call
1 (888) 915-2007
. In Canada, call
1 (866) 288-4268
. NOTE: Before calling for service, please review the user’s manual; a check of the PRODUCT’s controls and features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the PRODUCT(s) to the service location. The manufacturer will return repaired or replaced
PRODUCT under this limited warranty to you. Transportation, delivery or handling charges are prepaid. The manufacturer assumes no risk for damage or loss of the PRODUCT in transit. If the
PRODUCT failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, the manufacturer will notify you and will request that you authorize the cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of products that are not covered by this limited warranty.
6. What must you return with the PRODUCT to get warranty service?
You must:
• Return the entire original package and contents including the PRODUCT to the service location along with a description of the malfunction or difficulty; and
• Include a “valid proof of purchase” (sales receipt) identifying the PRODUCT purchased
(PRODUCT model) and the date of purchase or receipt; and
• Provide your name, complete and correct mailing address, and telephone number.
7. Other limitations
This warranty is the complete and exclusive agreement between you and the manufacturer of this AT&T branded PRODUCT. It supersedes all other written or oral communications related to this PRODUCT. The manufacturer provides no other warranties for this PRODUCT. The warranty exclusively describes all of the manufacturer’s responsibilities regarding the PRODUCT. There are no other express warranties. No one is authorized to make modifications to this limited warranty and you should not rely on any such modification.
State/Provincial Law rights: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the PRODUCT is fit for ordinary use) are limited to two years from date of purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall the manufacturer be liable for any indirect, special, incidental, consequential, or similar damages
(including, but not limited to lost profits or revenue, inability to use the PRODUCT or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this PRODUCT. Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.
97
Appendix
Technical specifications
RF frequency band
Channels
Operating temperature
Telephone base voltage
(AC voltage, 50/60Hz)
Telephone base voltage
(AC adapter output)
Headset jack
1921.536MHz - 1928.448MHz
5
32°F - 122°F
0°C - 50°C
100Vrms - 240Vrms
8VDC @1000mA
2.5mm, 32-150ohm
SynJ SB67158 small business system disclaimer range 980 feet
Open range test was performed by Wyle Laboratories, an independent commercial test facility. “Up to
980 feet” repeater range refers to the maximum open field range. Actual range may vary depending on intervening obstacles. Maximum operable range distances are based on all-indoor use.
DECT 6.0 digital technology
The AT&T DECT 6.0 products offer unsurpassed range performance and sound clarity. This is achieved through a unique antenna design and advances in noise-filtering technology. An independent laboratory has confirmed that AT&T DECT 6.0 products perform up to 45% better in range competitions. Now, calls can be taken in the basement, backyard and garage with exceptional sound quality.
Telephone operating range
This cordless telephone operates within the maximum power allowed by the Federal
Communications Commission (FCC). Even so, this handset and telephone base can communicate over a certain distance — which can vary with the locations of the telephone base and handset, the weather, and the construction of your building.
Redefining long range coverage and clarity
This telephone base comes with two antennas that gives much better clarity and covers a longer range than before. For even greater range, add optional repeaters (AT&T model SynJ SB67128).
98
Appendix
Troubleshooting
If you have difficulty with your telephone, please try the following suggestions.
For customer service, visit our website at call www.telephones.att.com
1 (888) 915-2007 . In Canada, dial 1 (866) 288-4268 .
or
My telephone base doesn’t work at all.
• Make sure the power cord is securely plugged in.
•
•
Make sure you plug the telephone line cord securely and firmly into the telephone base and the telephone wall jack.
Reset the telephone base. Unplug the electrical power. Wait approximately
15 seconds, then plug it back in. Allow up to one minute for the telephone base to reset.
•
•
Other electronic products such as HAM radios and other DECT phones, can cause interference with your cordless phone. Try installing your phone as far away as possible from these types of electronic devices.
You may need to purchase four AA alkaline batteries as backup battery to make the telephone base work in the event of a power failure. Please refer to Optional backup battery installation on page 9 in this user’s manual.
I cannot get a dial tone from the corded handset.
• First try all the suggestions, as mentioned above.
•
•
•
Make sure you plug the handset cord securely and firmly into the
HANDSET jack on the telephone base and the corded handset.
If the previous suggestions do not work, disconnect the telephone base from the telephone jack and connect to a different telephone. If there is no dial tone on that telephone either, the problem is in your wiring or local service. Contact your telephone service provider.
Your line cord might be malfunctioning. Try installing a new line cord.
I cannot dial out.
•
•
•
First try all the suggestions, as mentioned above.
Make sure you have a dial tone before dialing. The corded handset might take a second or two to connect the telephone base and produce a dial tone. This is normal. Wait an extra second before dialing.
Eliminate any background noise. Noise from a television, radio or other appliances might cause the telephone to not dial out properly. If you cannot eliminate the background noise, first try muting the corded handset before dialing, or dialing from another room by a cordless handset with less background noise.
• If the other telephones in your building are having the same problem, contact your telephone service provider.
99
Appendix
Troubleshooting
My telephone base isn’t performing normally.
•
•
•
Make sure you plug the power cord securely into the telephone base.
Plug the power adapter into a different working electrical outlet without a wall switch.
Reset the telephone base. Unplug the electrical power and remove all the batteries. Wait 15 seconds, then plug the power adaptor back in and install the batteries again. Allow up to one minute for the telephone base to reset.
Other electronic products such as HAM radios and other DECT phones, can cause interference with your cordless phone. Try installing your phone as far away as possible from these types of electronic devices.
I get noise, static, or weak signals even when I’m near the telephone base.
• If you subscribe to high-speed Internet service (DSL - digital subscriber line) through your telephone lines, you must install a DSL filter between each telephone line cord and telephone wall jack. The filter prevents noise and caller ID problems as a result of DSL interference. Please contact your DSL service provider for more information about DSL filters.
•
•
You may be able to improve the performance of your telephone base by installing your new telephone base as far as possible from any other existing corded or cordless telephone system that may already be installed.
Other electronic products such as HAM radios and other DECT phones, can cause interference with your cordless phone. Try installing your phone as far away as possible from these types of electronic devices.
•
•
•
•
Do not install this telephone base near a microwave oven or on the same electrical outlet. You might experience decreased performance while the microwave oven is operating.
If you plug your telephone in with a modem or a surge protector, plug the telephone base (or modem/surge protector) into a different location. If this does not solve the problem, relocate your telephone base or modem farther apart from one another, or use a different surge protector.
Relocate your telephone to a higher location. The telephone might have better reception in a high area.
If the other telephones in your building are having the same problem, contact your telephone service provider.
100
Appendix
Troubleshooting
I experience poor sound quality when using the speakerphone.
•
•
For increased sound quality while using the telephone speakerphone, place the telephone base on a flat surface.
Excessive background noise will cause a speakerphone to fade in and out. Try controlling the background noise by turning off any audio devices near the speakerphone. Also, try to avoid interrupting the person at the other end of the conversation while they are speaking. If background noise cannot be controlled, you should stop speakerphone operation and return to normal corded handset mode.
• When using a speakerphone, controlling background noise in your environment is essential. While you are listening to your party, press MUTE to temporarily turn your microphone off. When it is your turn to speak, remember to press MUTE again to turn the microphone on.
I hear other calls while using my telephone.
• Disconnect the telephone base from the telephone jack, and plug in a different telephone. If you still hear other calls, call your telephone service provider.
My telephone base does not ring when I receive a call.
• Make sure that the ringer is not off. Refer to the section on ringer selection in this user’s manual.
•
•
•
Make sure you plug in the telephone line cord securely into the telephone base and the telephone jack. Make sure you plug in the power cord securely.
You may have too many extension telephones on your telephone line to allow all of them to ring simultaneously. Try unplugging some of the other telephones.
If the other telephones in your building are having the same problem, contact your telephone service provider.
•
•
•
Test a working telephone at the telephone jack. If another telephone has the same problem, contact your telephone service provider.
Other electronic products such as HAM radios and other DECT phones, can cause interference with your cordless phone. Try installing your phone as far away as possible from these types of electronic devices.
Your line cord might be malfunctioning. Try installing a new line cord.
101
Appendix
Troubleshooting
My calls cut in and out while I’m using my corded handset.
• Other electronic products such as HAM radios and other DECT phones, can cause interference with your cordless phone. Try installing your phone as far away as possible from these types of electronic devices.
•
•
Do not install this telephone base near a microwave oven or on the same electrical outlet. You might experience decreased performance while the microwave oven is operating.
If you plug your telephone base in with a modem or surge protector, plug the telephone base (or modem/surge protector) into a different location. If this does not solve the problem, relocate your telephone base or modem farther apart from one another, or use a different surge protector.
•
•
•
•
Relocate your telephone base to a higher location. The telephone base might have better reception when installed in a high area.
If the other telephones in your building are having the same problem, contact your telephone service provider.
Excessive background noise will cause a speakerphone to fade in and out. Try controlling the background noise by turning off any audio devices near the speakerphone. Also, try to avoid interrupting the person at the other end of the conversation while they are speaking. If background noise cannot be controlled, you should stop speakerphone operation and return to normal handset mode.
When using a telephone base speakerphone, controlling background noise in your environment is essential. While you are listening to your party, press MUTE to temporarily turn your microphone off. When it is your turn to speak, remember to press MUTE again to turn the microphone on.
•
•
My caller ID isn’t working.
• Caller ID is a subscription service. You must subscribe to this service from your telephone service provider for this feature to work on your telephone base.
•
The caller must be calling from an area that supports caller ID.
Both your and your caller’s telephone service providers must use caller ID compatible equipment.
If you subscribe to high-speed Internet service (DSL - digital subscriber line) through your telephone lines, you must install a DSL filter between each telephone line cord and telephone wall jack. The filter prevents noise and caller ID problems resulting from DSL interference. Please contact your DSL service provider for more information about DSL filters.
102
Appendix
Troubleshooting
System does not receive caller ID when on a call.
• Make sure you subscribe to caller ID with call waiting features from your telephone service provider. Caller ID feature works only if both you and the caller are in areas offering caller ID service, and if both telephone service providers use compatible equipment.
The answering system is recording incomplete messages.
• If a caller leaves a very long message, part of it may be lost when the system disconnects the call after three minutes.
•
•
If the caller pauses for longer than six seconds, the system stops recording and disconnects the call.
If the system’s memory becomes full during a message, the system stops recording and disconnects the call.
• If the caller’s voice is very soft, the system may stop recording and disconnect the call.
I have difficulty hearing messages.
• Press VOL+ to increase the speaker volume on the telephone base.
System does not answer after the correct number of rings.
• Make sure that the answering system is on (page 74).
•
•
•
•
•
If toll saver is selected, the number of rings changes to two when there are new messages waiting (page 32).
If the memory is full or if the system is off, the answering system answers after 10 rings.
In some cases, the answering system is affected by the ringing system used by your telephone service provider.
If you subscribe to voicemail service, change the number of rings so that your answering system answers before your voicemail answers (page 72). To determine how many rings activate your voicemail, contact your telephone service provider.
If there is a fax machine connected to the same telephone line, try disconnecting the fax machine. If that solves the problem, consult your fax machine documentation for information on compatibility with answering systems.
103
Appendix
Troubleshooting
System does not record messages.
• Make sure the answering system is on (page 74).
• Make sure the memory of the answering system is not full. Please refer to the Remaining space section on page 38 in the user’s manual. When the answering system memory is full, it does not record new messages until some old messages are deleted.
•
•
If you subscribe to voicemail service, change the number of rings so that your answering system answers before your voicemail answers (page 72).
To determine how many rings activate your voicemail, contact your local telephone service provider.
If there is a fax machine connected to the same telephone line, try disconnecting the fax machine. If that solves the problem, consult your fax machine documentation for information on compatibility with answering systems.
System does not respond to remote commands.
• Make sure to enter your remote access code correctly (page 83).
touch-tone telephone and cannot activate the answering system.
• The answering system may not detect the remote access code while your announcement is playing. Try waiting until the announcement is over before entering the code.
pad keys firmly.
Outgoing announcement is not clear.
• When you record your announcement, make sure you speak in a normal tone of voice, about nine inches from the telephone base.
• Make sure there is no background noise (TV, music, etc.) while recording.
COVM shows on the screen display and I do not know why.
• Your telephone has voicemail indication that is separate from the built-in answering system. If COVM appears on the display, then your telephone has received a signal from your telephone service provider.
Contact your telephone service provider for more information on how to access your voicemail.
104
Appendix
Troubleshooting
I cannot retrieve voicemail messages.
• Your telephone has both a built-in answering system and voicemail indication. They are independent features and each alerts you to new messages differently (page 72). If you subscribe to voicemail service from your telephone service provider, contact your telephone service provider for more information on how to access your voicemail.
I have problems recording music or voice messages.
• If you are using an audio device, make sure the audio cable has been firmly plugged into your telephone and your audio device.
• If you are using the corded handset, make sure the corded handset has been firmly plugged into the telephone base.
I subscribe to a nontraditional telephone service that uses my computer to establish connections, and my telephone doesn’t work.
• Make sure your computer is powered on.
• Make sure your Internet connection is working properly.
•
•
•
•
Make sure that the software is installed and running for your nontraditional telephone service.
Make sure to plug your USB telephone adapter into a dedicated USB port on your computer. Do not plug it into a multiple port USB hub (USB splitter) that is not powered.
In a few rare instances, the USB port on your computer may not have enough power. Try using a USB hub with its own external power supply.
If you are using a firewall, it may prevent access to your nontraditional telephone service provider. Contact your service provider for more information.
•
•
•
•
•
•
Common cure for electronic equipment.
If the telephone base does not seem to be responding normally, do the following (in the order listed):
Disconnect the power to the telephone base.
Disconnect the backup batteries.
Wait a few minutes.
Connect power to the telephone base.
Install the backup batteries again.
Wait for reestablishing the connection with the telephone base. Allow up to one minute for this to take place.
105
Index
Index
A
AC power 6
Add a cordless headset 12 a deskset 11 a handset 10
Alert confirmation call 37 on or off 36 set alert number 36
Announcement record 29–30, 33 select 33 transferred call 57
Announce only 73, 82
Answer incoming a call 46 intercom call 55 push to talk (PTT) call 59
Answering system 72–84
Antennas 98
Auto attendant flow chart 77 multiple auto attendants 76 operation 75–77 setup 29–31
B
Blind transfer 56
C
Call alert tone 28
Caller ID delete entries 69 dial an entry 69
Review information 68 save entries to directory 70
106
Call privacy 48
Call screening 34
Call transfer 56–57
Call waiting 47, 66
Capacity 60, 74
Central office voicemail (COVM) on or off 53 reset 53
Chain dialing 51
Conference calls 51–52
Customer support 41
D
Deskset mailbox setup 39–40
Default announcement 29 music 23–24, 26
Delete all old messages 79 call log entries 69 directory entries 65
Deliver a memo 81
Deregister a cordless headset 13 desksets 13 handsets 13
Deskset registration 11
Dialing call log entry 69
Directory entry 65
Dial pad 61
Directory capacity 60 edit entries 65 entry dialing 65
Index
Index name search 64 new entries 61
Directory card 2
Display dial 65
E
End conference call 52 intercom call 55 push to talk (PTT) call 59
F
Fast answer mode 39
Flash 62
H
Handset mailbox setup 39–40
Handset registration 11
Handsfree use 45, 57
Headset corded installation 14 cordless operation 85
Hold 50
I
Hold reminder 22
Important safety information 90–91
Incoming messages 78
Indicator lights 43
Indicator tones 42
Installation corded headset 14 telephone base 6
Intercom answer 55 end 55 with a cordless handset 54 with a deskset 54
107
J
Join a call in progress 51
L
Last number redialing 46
Limited warranty 96–97
Line indicators 42
Low battery 9
M
Mailbox setup 32–38
Maintenance 89
Make call 44–45 conference call 52–53 intercom call 54–55 push to talk (PTT) call 58
Memo play back 82
Record and deliver 81
Memory match 68
Menu settings 15
Message indication 78
Message playback 78
Missed (new) calls indicator 68
Music on hold (M.O.H.) 23–27
Mute 50
N
Name enter into directory 61–62 search 64
Navigation keys 1
New message indication 78
Notify alert 36–37
Number of rings 31–32
O
One-touch keys 2
Index
Index
On hook dialing (predialing) 45
Outgoing calls 20
P
Pause 62
Persistent hold 35
Planning your system 5
Play back memo 82 message 78–79
Power adapter 6–8
PTT (push to talk intercom) all devices 58 answer 59 convert to intercom 59 end 59
Q single handset 58
Quick reference guide 1–3
R
Record announcement 29 call 49 extension list 30 memo 81
Redial 46
Registration cordless handset 10 cordless headset 12 deskset 11
Remaining space 38
Remote access 83–84
Repeater 5, 98
Restricted prefix 18
Review caller ID information 68 directory entries 63
108
S
Screen display messages 86–88
Screen icons 42
Search by name 64
Set date and time 22
Speed dial enter, edit or delete number 41 setup 41
T
Technical specifications 98
Telephone base operation 44–59
Telephone operating range 98
Temporary ringer silencing 46
Three-way conference calls 51–52
Transfer call 56–57 message 80
Troubleshooting 99–105
Turn off answering system 82 auto attendant 82 general delivery mailbox 82
Two-way communication 58
Two-way intercom 59
Two-way recording 91
V
Voicemail
COVM 53 from answering system 72
Voice prompt 74–75
Volume control 47
W
Warranty 96–97
Remote access wallet card
Use the wallet card below to help you remember commands to control your answering system from any touch-tone telephone.
Cut along dotted line.
Fold here.
Call your telephone number, then enter your four-digit access code (preset to 0000).
Action Remote command
Play all messages .............................................................
1
Delete the message .........................................................
3
Repeat the message ........................................................
4
Listen to the previous message .................................
4
(twice)
Help menu and return to the
remote commands .....................................................
5
Skip the message ..............................................................
6
Transfer the message ......................................................
7
End remote access call ..................................................
*
(or hang up)
Model name: SynJ SB67158
Type: DECT 6.0 4-line corded/cordless small business system
© 2011-2014 Advanced American Telephones. All Rights Reserved. AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to
Advanced American Telephones, San Antonio, TX 78219. Printed in China.
www.telephones.att.com
© 2011-2014 Advanced American Telephones. All Rights Reserved.
AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to
Advanced American Telephones, San Antonio, TX 78219.
SynJ® is a trademark of Advanced American Telephones.
Printed in China. Issue 11.0 AT&T 11/14.
Advertisement