E-LINK LNK-IMC3011-SFP Quick Start Manual
E-LINK LNK-IMC3011-SFP is a hardened 10/100/1000Base-T to 1000Base-X SFP Ethernet media converter. It provides SFP ports to support the use of SFP (Small Form-factor Pluggable) transceiver modules, allowing you to choose different types of SFPs (1000M only) to meet your specific needs. The converter supports 1 or 2 core Single-mode or Multi-mode fiber, making it suitable for a wide range of applications.
Advertisement
Advertisement
LNK-IMC3011-SFP
Hardened 10/100/1000Base-T to 1000Base-X SFP Ethernet Media Converter
This quick start guide describes how to install and use the Gigabit media converter. This is the Media Converter of choice for harsh environments subject to space and temperature constraints.
Overview
LNK-IMC3011-SFP is a 10/100/1000Base-T to 1000Base-X Ethernet media converter. The converter provides SFP ports to support the use of SFP (Small Form-factor Pluggable) transceiver module. User can chose different types of SFPs (1000M only). The Switch supports 1 or 2 core Single-mode or
Multi-mode fiber. The product operates at temperatures ranging from -40 o C to 75 o C and support Din-rail installed or wall-mount installed.
General
To ensure trouble free transportation and storage, all products must be thoroughly inspected, tested and properly packed before delivery. Check the product upon receipt for any visible damage which may have been caused during shipment.
Package Content
Hardened 10/100/1000Base-T to 1000Base-X SFP Ethernet Media Converter x 1
Quick Start Guide x 1
Physical Description
Front Panel
Rear Panel
1 V1.0
LNK-IMC3011-SFP
Hardened 10/100/1000Base-T to 1000Base-X SFP Ethernet Media Converter
Installation
SFP Optical Module
You can select different SFP modules as required (Please refer to our SFP Ordering Options for the appropriate module).
To insert/remove the SFP, the procedures are as follows:
1. On the front panel, insert the SFP module into the SFP port until it is securely locked.
2. Connect the optical fiber (1/2 core) to the LC connector(s) of the SFP.
3. To remove the SFP module, press down the lock of the LC connector of the optical fiber to pull out the fiber cable.
4. Pull down the SFP lever and hold its position. Pull out the SFP module from the SFP port.
2 V1.0
LNK-IMC3011-SFP
Hardened 10/100/1000Base-T to 1000Base-X SFP Ethernet Media Converter
DIN Rail Installation
LNK-IMC3011-SFP can be installed on a DIN rail. Installation steps are as follows:
Press Upper part
1. Tighten the screws to fix the
DIN Rail plate
2. Lock the upper part of the DIN rail clip on the upper side of the track. Press it until the metal part move downward and a “click sound is heard”
Wall Mount Installation
LNK-IMC3011-SFP also can be installed on a Wall Mount. Installation steps are as follows:
1. Tighten the screws to fix the
DIN Rail plate
2. Mount the switch on the wall or on a flat surface with 2 screws piercing through the mounting holes to secure it in position.
Setup
1.
Connect one end of each Ethernet cable to its corresponding port on the LNK-IMC3011-SFP.
Connect the other end to the network equipment (IP camera, Switch or PC). Insert the SFP and connect the optical fiber cable to its corresponding connector.
2.
Connect the LNK-IMC3011-SFP to the power supply. Ensure the power supply in connected to a power source and the PWR indicator is ON. If not, please ensure that the power cable is connected properly and the power supply is functioning normally.
3.
After all cables are connected, the indicators will be lit as per port status LEDs (page 5).
3 V1.0
LNK-IMC3011-SFP
Hardened 10/100/1000Base-T to 1000Base-X SFP Ethernet Media Converter
Interface
RJ-45 Pin Assignment
6
7
4
5
8
2
3
Pin
1
TP2+
TP2-
TP1-
TP3+
TP3-
MDI
TP0+
TP0-
TP1+
Assignment
MDIX
TP1+
TP1-
TP0+
TP3+
TP3-
TP0-
TP2+
TP2-
Power Connection
Pin
Description
Power Input
V -
GND
V +
+12~48VDC
LED Indicators
Indicator
PWR
SFP LINK
LINK/ACT
Color
Green
Green
Green
Status
ON
ON
OFF
ON
Blinking
OFF
Description
Powered on
Fiber Link up
Fiber is not connected or Fiber link down
A network device is connected
The connected device is transmitting/ receiving data
No network device is connected
4 V1.0
LNK-IMC3011-SFP
Hardened 10/100/1000Base-T to 1000Base-X SFP Ethernet Media Converter
Dimensions of the LNK-IMC3011-SFP (Unit: mm)
Functional Description
Converts 10/100/1000Base-T to 1000Base-X SFP
RJ45 port support 10/100/1000Mbps-Full/Half-duplex, Auto-negotiation, Auto-MDI/MDIX
Fiber port supports external 1000BASE SFP
Support 12 VDC or 24 VAC power input
-40 ° C to 75 ° C ( -40 ° F to 167 ° F) operating temperature range
Supports Wall-mount and Desktop installation
5 V1.0

Public link updated
The public link to your chat has been updated.
Advertisement