CYP DS-MSC Operation Manual
Advertisement
Advertisement
DS-MSC
Digital Signage Multi-Screen
Video Wall Controller
OPERATION MANUAL
Safety Precautions
Please read all instructions before attempting to unpack or install or operate this equipment, and before connecting the power supply.
Please keep the following in mind as you unpack and install this equipment:
Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
Never spill liquid of any kind on or into this product.
Never push an object of any kind into this product through module openings or empty slots, as you may damage parts.
Do not attach the power supply cabling to building surfaces.
Do not allow anything to rest on the power cabling or allow it to be abused by persons walking on it.
To protect the equipment from overheating, do not block the slots and openings in the module housing that provide ventilation.
Revision History
Version No
RDV01
RDV02
RDV03
RDV04
Date
20110119
20110317
20110324
20110719
Summary of Change
Preliminary Release
Add New OSD Menu
Change OSD Figures
Add TV Option
Table of Contents
1. Introduction ……………………..……………………...…........….…….
2. Applications …………………..………………….……...................…..
3. Package Contents ………………………...........……….................…
4. System Requirements ……………..……….........………............…….
5. Features …………………………………………......……........…...……
6. Specifications ………………………………...……..........………....….
7. Operation Controls and Functions ……………...……..............……
7.1 Front Panel ..............................................................................
7.2 Rear Panel .…………………………………..…….......…...….…
7.3 OSD Menu .…………………………………..…….......…...….…
8. Remote Control .......................…......……………..........…..…....…...
9. RS-232 Protocol ................................................................................
9.1 Pin Definition .............................................................................
9.2 Command ...............................................................................
10. Connection and Installation ….………………….........…..…..…......
11. Acronyms …......................................................................................
8
9
7
7
6
7
4
5
4
4
2
3
1
1
1
1
1. Introduction
To capture the public’s attention, the Multi-Screen Video Wall control system is ideal for advertising, entertaining and displaying information. The device allows users to display HDMI or PC sources to multiple LCD monitors, while thanks to the built-in RS-232 you are able to fully customize the LCD panels giving you complete control over 2x2, 3x3, 4x4 and 5x5 video walls. This device is also embedded with a PC to HDMI scaler, which allows the input
PC video signal to be integrated and converted to digital HDMI signal output to the video wall. There is a pair of additional L/R RCA connecters for user to output analog audio (extracted from the HDMI source, or routed from the analog audio input) to local speakers. Further, the IR remote and the RS-232 control free users with on hand control from anywhere they wish.
2. Applications
TV wall
Video wall
Display wall
Gaming wall
Movie wall
Combination advertising wall
3. Package Contents
Video wall control system(s)
5V DC power adaptor(s)
Operation Manual
4. System Requirements
HDMI or PC splitter/matrix with input source signal and connection cables, display TV/monitor with connection cables.
1
5. Features
Supports 6 or more video wall combinations of HxV: 2x2(four monitors),
3x2(sis monitors), 3x3(nine monitors), 4x3(12 monitors),4x4(16 monitors) and 5x5 (25 monitors)
Supports both HDMI and PC (with audio) input sources
Resolution support up to 1080p full HD
Use RS-232 cables to cascade over every connected CVW-11HS boxes to remotely control each monitors with one setting only.
Supports external IR receiver for IR remote control
Note: Requires HDMI or PC (with audio) signal splitter to distribute vide / audio signal to each connected CVW-11HS box.
2
6. Specifications
Input Ports
Output Ports
IR Frequency
1xHDMI, 1xPC, 1xRS-232 (female jack), 1xIR,
1xL/R (3.5Ø phone jack)
1xHDMI, 1xRS-232 (male jack), 1xL/R (RCA jack)
38Hz
IR Cable Length 3M
Input Resolution Supports PC: VGA ~ SXGA
Output Resolution
Supports
Audio Format
HDMI: 48op~1080p
HDMI: 720p & 1080p
Power Supply
ESD Protection
PCM 2Ch
5V/3.6A DC (US/EU standards, CE/FCC/UL Certified)
Human body model: ± 8kV (air-gap discharge)
± 4kV (contact discharge)
200 (W) x 155 (D) x 45(H) Dimension (mm)
Weight (g)
Chassis Material
815
Aluminum
Silkscreen Color Black
Operating Temperature 0˚C ~ 40˚C / 32˚F ~ 104˚F
Storage Temperature
Relative Humidity
-20˚C ~ 60˚C / -4˚F ~ 140˚F
20 ~ 90% RH (Non-condensing)
Power Consumption (W) 15.5
3
7. Operation Controls and Functions
7.1 Front Panel
HDMI IN AUDIO IN PC IN RS 232 IN RS 232 OUT IR IN
DS-MSC Video Wall Controller
① ② ③ ④ ⑤ ⑥
① HDMI IN: This slot is to connect from HDMI splitter or matrix with input
source signal.
② Audio IN: This slot is to connect with the audio signal from the source
equipment with 3.5Ø phone jack.
③ PC IN: This slot is to connect from PC/RGB splitter or matrix with input
source signal.
④ RS-232 IN: As a first device of the video wall system, this slot is to connect
with PC/NB equipment for RS-232 control. Starting from the second device
of the video wall system this slot should be connect from the RS-232 out of
the last device.
Note: For RS-232 control it required a special level-shift board and it is an
optional accessory selection.
⑤ RS-232 OUT: This slot is to connect to the next video wall control system’s
RS-232 IN.
⑥ IR IN: This slot is to connect with IR blaster included in the package for
receiving the IR signal of the device’ remote controller.
7.2 Rear Panel
L
HDMI OUT
DC 5V
AUDIO OUT
R
① ② ③
① DC 5V: Connect this slot with power adaptor included in the package
from the AC wall outlet. When the power is plugged on the device will
automatically power ON.
② Audio OUT L/F: These slots are to connect with RCA jack cables to the
active speaker or to display’s audio input.
③ HDMI OUT: This slot is to connect to the display with HDMI input.
4
7.3 OSD Menu
MAIN MENU
PICTURE
MENU*1
SETUP MENU*1
STANDARD
R OFFSET
G OFFSET
B OFFSET
R GAIN
G GAIN
B GAIN
ON/OFF
0~255 (118)
0~255 (116)
0~255 (118)
0~255 (098)
0~255 (098)
0~255 (098)
CONTRAST
BRIGHTNESS
LANGUAGE
HDMI SOUND
0~63 (50)
0~63 (40)
ENG / T.CHINESE (ENG)
ON/OFF (ON)
STANDARD ON/OFF (OFF)
H POSITION START 000~385 (*2)
V POSITION START 000~53 (*2)
H ZOOM SIZE 000~255 (0)
V ZOOM SIZE 000~255 (0)
TV Option Width 1~10 (1)
TV Option Height 1~10 (1)
*NOTE: 1. The Picture Menu allows users to adjust single monitor’s setting while
the Setup Menu will only needs to be adjust once and all monitors
will be automatically adjusted.
2. Defual value will adjusted automatically depending the the input
signal's timing.
Picture Standard: Set it to ON will allow system to set the picture menu into the default value as indicated in the ( ).
Picture R/G/B Offset: These functions are to set the single picture's R/G/B brightness.
Picture R/G/B Gain: These functions are to increase or decrease the color of single picture's R/G/B.
Picture Contrast: This function is to set the single picture's color contrast.
Picture Brightness: This function is to set the single picutre's brightness.
Setup Language: There are two language available in the OSD and they are
English and Traditional Chinese.
Setup HDMI Sound: This function is to set the HDMI output audio sound to be
ON or OFF.
Setup Standard: Set it to ON will allow system to set the setup menu into the default value as indicated in the ( ).
5
Setup H/V Position Start: These functions are to set the total value of the vertical and horizontal value of the TV wall.
Setup H/V Zoom Size: These functions are to set the total value of the vertical and horizontal zoom in and zoom out size of the TV wall.
Setup H/V Blanking Edit: These functions are to set the total value of the vertical and horizontal value of the blanking area of the TV wall.
Setup TV Option Width: This function is to set the numbers of the TV/display
that is to be on a horizontal line of the TV wall.
Setup TV Option Height: This function is to set the numbers of the TV/display
that is to be on a vertical line of the TV wall.
8. Remote Control
①
Power: Press this button to switch on the
device(s). All the connected Video wall system
control device(s) will be switch to ON.
②
Power OFF: Press this button to switch off the
device. All the connected Video wall system
control device(s) will be switch to OFF.
③
SINGLE: Press this button to set the image
to be displayed on each and every connected
TV/monitor identically.
④ FULL: There are 6 options of setting an image
to be displayed on TV/ monitor and they are
2x2, 3x3, 4x4, 3x2, 4x3 and 5x5.
⑤ pqtu &OK: Press the arrow buttons to select
and adjust the selection in the OSD menu and
value or to select the display. Press OK to
confirm the selection.
⑥
MENU: Press this button to enter into the OSD
menu. When the setting is selected and
confirmed all the output display will
automatically changed to the selected settings.
⑦
RETURN: Press this button to return to the last
layer of OSD selection or to exit the OSD.
⑧
HDMI: Press this hot key to select the input source
from HDMI IN.
⑨
⑫
①
③
④
⑤
⑦
⑧
⑪
POWER
2X2
3X2
RETURN
HDMI
720P
POWER OFF
SINGLE
3X3
4x3
FULL
OK
VGA
OPTION
CR-98
4X4
5x5
MENU
U/OVER
1080P
②
⑥
⑩
⑬
⑨
VGA: Press this hot key to select the input source
from PC IN.
⑩
U/OVER: Press this key to adjust the screen when the image is overscan or
underscan.
⑪
720P: Press this hot key to switch the output timing to 720p
⑫ OPTION: Press this key to switch to the special setting of the display image
set by the factory design.
⑬
1080P: Press this hot key to switch the output timing to 1080p
*Function that automatically adjust all monitors in once.
6
9. RS-232 Protocol
9.1 Pin Definition
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
Pin 9
RS-232 IN
NC
TxD
RxD
NC
GND
NC
Connect to Pin 8
Connect to Pin 7
NC
Baud Rate: 19200bps
Data bit: 8 bits
Parity: None
Stop Bit: 1 bit
Flow Control: None
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
Pin 9
RS-232 OUT
NC
RxD
TxD
NC
GND
NC
Connect to Pin 8
Connect to Pin 7
NC
9.2 Command
COMMAND
0x23 0x53 0x30 0x30 0x31 0x23
0x23 0x53 0x30 0x30 0x30 0x23
POWER ON
POWER OFF
UNDER SCAN
OVER SCAN
ACTION
0x23 0x43 0x30 0x30 0x30 0x23
0x23 0x43 0x30 0x30 0x31 0x23
0x23 0x43 0x52 0x11 0x00 0x23
0x23 0x43 0x52 0x11 0x00 0x23
0x23 0x43 0x52 0x11 0x00 0x23
0x23 0x43 0x52 0x11 0x00 0x23
0x23 0x43 0x52 0x11 0x00 0x23
0x23 0x43 0x52 0x11 0x00 0x23
0x23 0x43 0x52 0x11 0x00 0x23
0xEF 0x05 0xD7 0xC0 0x22 0x07 0xEE
SINGLE
2x2
3x3
4x4
5x5
3x2
4x3
Change to HDMI
0xEF 0x05 0xD0 0xC0 0x22 0x00 0xEE Change to PC
0xEF 0x06 0x8A 0xC0 0x20 0x01 0xBB 0xEE Option
7
10. Connection and Installation
1. Connect the HDMI source (such as DVD or PS3) into the “HDMI IN” of the HDMI splitter and connect the “HDMI OUT” from the splitter to Video
Wall control systems (CVW-11HS) respectively. Connect each Control system HDMI output port to each LCD monitor’s HDMI input port. The display sequence should be from top left to right and from second right to left. For more details please refers to the diagram.
2. IR receiver must connect to the rst Video Wall control system IR input port.
Meanwhile, connect the rst RS-232 output port to second system of RS-232
input port and vise verse. (The upper left will be the rst LCD monitor of the
connection diagram above).
① ②
FULL
① ②
SINGLE
④ ③ ④ ③
①
HDMI
②
HDMI
③
HDMI
④
HDMI
DS-MSC DS-MSC DS-MSC DS-MSC
HDMI HDMI HDMI HDMI
IR Cable
CHDMI-4
(HDMI Splitter)
HDMI or or
Blu-ray PS3
Laptop
NOTE: Display sequence is from top left to right and from second right to left and so on sequence.
8
Acronyms
Acronym
HDMI
Complete Term
High-Definition Multimedia Interface
A
9
www.cypeurope.com

Public link updated
The public link to your chat has been updated.
Advertisement