American Bicycle Security Company Bike File Specifications and Assembly Instructions
Advertisement
Advertisement
Bike File
The Bike File is our most space efficient u-lock compatible product. Sliding hangers allow nine bikes to be securely stored in an eight foot section while allowing for easy loading and unloading of bikes.
The Bike File is ideal for indoor bike rooms where space is at a premium and security is an issue.
Ceiling mount, wall mount and floor mount options are available.
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Bike File
Height Requirement: 97”
Product
Capacity
Materials
Finishes
Installation
Methods
Space Use &
Setbacks
Bike File
9 bikes per 8 foot unit
12 gauge galvanized steel trolley track
Stainless steel trolley assembly
1” 16g arms
An after fabrication hot dipped galvanized finish is our standard option.
The Bike File is available in a wall-mounted or ceiling mounted configuration. Please contact us if you are interested in a floor-mounted Bike File.
Bike Files may be lined up end to end to fill the available space. A 36” aisle should be left between racks facing one another.
Example of rack in use
*Optional wheel stop for floor mounted only. Recommended for double sided.
Page 1 of 5
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Bike File
Wall Mount – Parts List
Page 2 of 5
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Bike File
Wall Mount – Installation
*Tools Needed for Installation
9/16” Wrench/Socket
3/4” Wrench/Socket
1/4” Drill Bit or 3/8” Masonry Drill Bit (depending on anchor type)
Tape Measure
Drill (Hammer Drill Recommended)
Hammer
Level
Saw for cutting rack
Installation Steps:
Before installing, Make sure the wall is strong enough to accommodate the rack fully loaded with bikes. Compare parts shipped with rack to parts list. Call us if any parts are missing.
1.
Mount 24” Slotted Tracks vertically to the wall with the appropriate anchors. Use a level for greatest accuracy. The bottom edge of the Slotted Track should be approximately
72” off the floor. The Slotted Tracks should be 4’ apart from each other, and the end Slotted Tracks should be 2’ from the eventual position of the end of the Trolley track.
2.
Mount the remaining 24” Slotted Tracks horizontally and protruding from the wall so that the slotted surface of the
Slotted Track is 4.25” below the top edge of the vertical
24” Slotted Track. Use the Knee Braces, Angle Brackets, and the Spring-loaded Nuts and Hex Head Cap Screws to secure the horizontal Slotted Track in place.
3.
Make sure the horizontal Slotted Track is level. Adjust if necessary.
4.
Attach the Bike File to the Wall Mount assemblies by securing the Channel Trolley Supports to the horizontal
24” Slotted Track with the remaining Spring-loaded Nut and Hex Head Cap Screw. The edge of the Slotted Track
Mounting Bracket should be flush with the edge of the 24”
Slotted Track.
4.
5.
Follow the installation instructions for the basic Bike File unit to complete the assembly.
3.
1.
2.
Page 3 of 5
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Bike File
The floor mounted Bike File MUST be anchored to the floor.
This is NOT a freestanding unit
Floor Mount – Parts List
Page 4 of 5
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Installation Steps:
Bike File
Floor Mount – Installation
*Tools Needed for Installation
9/16” Wrench/Socket
3/4” Wrench/Socket
1/4” Drill Bit or 3/8” Masonry Drill Bit (depending on anchor type)
Tape Measure
Drill (Hammer Drill Recommended)
Hammer
Level
Saw for cutting rack
Installation Steps:
Before installing, Make sure the wall is strong enough to accommodate the rack fully loaded with bikes. Compare parts shipped with rack to parts list. Call us if any parts are missing.
1.
Stand the (2) uprights parallel to each other and 48” apart
2.
3.
4.
Attach the Bike File to the Floor Mount assembly by securing the Channel Trolley Supports to the uprights with ½” x 3” bolts.
Follow the installation instructions for the basic Bike File unit to complete the assembly.
Position Single-sided Floor Mount Assembly and anchor the uprights to the floor with the appropriate anchors.
2.
1.
3.
Page 5 of 5
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]

Public link updated
The public link to your chat has been updated.
Advertisement