Track Rack
The Track Rack’s unique staggered, sliding hook design creates the greatest parking efficiency while still providing easy access to any particular bike. When adding or removing a bike to the rack, simply push the surrounding bikes out of the way.
* Track Racks are not lockable
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Track Rack
Height Requirement: 97”
Product
Capacity
Materials
Installation
Methods
Space Use
& Setbacks
Track Racks
Capacity of the Track Rack will vary by lengths ordered.
At maximum capacity, bikes will be parked 8” apart. Each
8 foot length will accommodate 13 bikes.
12 gauge galvanized steel
Stainless steel trolley assembly
¼” zinc-plated steel hooks
The Track Rack is available in a wall-mounted and floormounted.
Track Racks may be lined up end to end to fill the available space. A 36” aisle should be left between racks facing one another.
Page 1 of 5
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Track Rack
Wall Mount Parts List
Page 2 of 5
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Track Rack Installation Instructions
Wall Mount
*Tools Needed for Installation
9/16” Wrench/Socket
¾” Wrench/Socket
¼” Drill Bit or 3/8” Masonry Drill Bit (depending on anchor type)
Tape Measure
Drill (Hammer Drill Recommended)
Hammer
Level
Saw for cutting rack
Installation Steps
Before installing: Make sure the wall is strong enough to accommodate the rack fully loaded with bikes. Compare parts shipped with rack to parts list. Call ABSCo if any parts are missing.
2.
1.
3.
Page 3 of 5
1.
Mount 24” Slotted Tracks vertically to the wall with the appropriate anchors. Use a level for greatest accuracy. The bottom edge of the
Slotted Track should be approximately 72” off the floor. The Slotted Tracks should be 4’ apart from each other, and the end Slotted Tracks should be 2’ from the eventual position of the end of the Trolley track.
2.
Mount the remaining 24” Slotted Tracks horizontally and protruding from the wall so that the slotted surface of the Slotted Track is
4.25” below the top edge of the vertical 24”
Slotted Track. Use the Knee Braces, Angle
Brackets, and the Spring-loaded Nuts and Hex
Head Cap Screws to secure the horizontal
Slotted Track in place.
3.
Make sure the horizontal Slotted Track is level.
Adjust if necessary.
4.
Attach the Track Rack to the Wall Mount assemblies by securing the Channel Trolley
Supports to the horizontal 24” Slotted Track with the remaining Spring-loaded Nut and Hex
Head Cap Screw. The edge of the Slotted Track
Mounting Bracket should be flush with the edge of the 24” Slotted Track.
5.
Follow the installation instructions for the basic
Track Rack unit to complete the assembly.
4.
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Track Rack
Floor Mount Parts List
The floor mounted Track Rack MUST be anchored to the floor. This is NOT a
Freestanding unit
Page 4 of 5
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Track Rack
*Tools Needed for Installation
¾” wrench/socket, qty. 2
3/8” masonry bit
9/16” wrench/socket
Tape measure
Drill (hammer drill recommended)
Hammer
Level
Installation Instructions
Floor Mount
Installation Steps
Before installing: Make sure the floor is strong enough to accommodate the rack fully loaded with bikes. Compare parts shipped with rack to parts list. Call ABSCo if any parts are missing.
1.
Place the Uprights 48” apart from each other. See your rack layout for location and numbers.
2.
Anchor each Upright by drilling 3/8” holes and fastening with wedge anchors.
3.
A) For single-sided units, fasten the Upright Braces to the Uprights with 3/8” x 3” bolts, 3/8” washers,
3/8” lock washers, and 3/8” nuts.
B) For double-sided units, fasten the Double-sided
Uprights and Upright Braces to the Uprights with 3/8” x 3” bolts, 3/8” washers, 3/8” lock washers, and 3/8” nuts.
4.
A) For single-sided units, attach Knee Braces to the first Upright and then every other Upright with 3/8” x 3” bolts, 3/8” washers, 3/8” lock washers, and
3/8” nuts. Anchor each Knee Brace by drilling a 3/8” hole and fastening with a wedge anchor.
B) For double-sided units, attach (2) Knee Braces to the first Upright and then every other Upright with
3/8” x 3” bolts, 3/8” washers, 3/8” lock washers, and 3/8” nuts. Anchor each Knee Brace by drilling a
3/8” hole and fastening with a wedge anchor.
5.
Fasten the Channel Supports to the uprights with ½” x 3” bolts, ½” washers, ½” lock washers, and ½” nuts.
Use the following Channel support mounting locations:
1st Upright, use right hole.
2nd Upright, use center hole.
3rd Upright, use left hole.
For modular units each 3rd Upright will have a
Channel
Support at the left and right holes.
6.
Insert the Track Rack or Bike File assembly into the
Channel Supports and secure. See Track Rack or
Bike File instructions for more detail.
Page 5 of 5
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
