American Bicycle Security Company Ultra Space Saver – Single Specifications and Assembly Instructions
American Bicycle Security Company Ultra Space Saver – Single
This rack is great for property managers, commercial parking garages, and for home storage use. The Ultra Space Saver Single Rack’s compact design lets you convert otherwise unusable space to bike parking.
Features:
- U-lock compatible
- Holds 1 bike
- Made of 1” OD 11 gauge tube (square or round available) with ½” steel round bar hanger
- Black powder coat loop with rubber coated hanger arm
- Wall mount has two 2.5” x 6” foot plates set 25” apart (Centerline to centerline) with 4 fasteners
Installation:
- Requires four anchors drilled into the wall
Advertisement
Advertisement
Ultra Space Saver Single
U-lock compatibility makes this rack great for property managers, commercial parking garages, and for home storage use. The Ultra Space Saver
Single Rack’s compact design lets you convert otherwise unusable space to bike parking.
Quick installation only requires four anchors drilled into the wall. Save room today with the
Ultra Space Saver Single, or check out the whole modular
Ultra Space Saver system if you need to park many bikes.
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Ultra Space Saver Single
Height Requirement: 87”
Product
Capacity
Materials
Finishes
Installation
Methods
Space Use &
Setbacks
Ultra Space Saver Single
1 Bike
Body is 1” OD 11 gauge tube (square or round available) with
½” steel round bar hanger. Mounting flanges are ¼” plate.
Black powder coat loop with rubber coated hanger arm.
Wall mount has two 2.5” x 6” foot plates set 25” apart
(Centerline to centerline) with 4 fasteners. Can be set into concrete block, solid concrete, bricks, wood studs and other base materials.
Racks should be placed minimum 16” apart. When installing racks next to each other, their heights should be staggered by 10”. See diagram for approximate space use when loaded and recommended setbacks.
Example of rack in use
Page 1 of 4
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Ultra Space Saver Single
How to use:
Pivot bike onto rear wheel Use leg or hip to raise bike
Hook Wheel onto peg Secure bike onto rack through tire & frame
Page 2 of 4
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Ultra Space Saver Single
Installation
*Tools Needed for Wall Mount Installation
9/16” Wrench/Socket
Masonry Drill Bit
Tape Measure
Drill (Hammer drill recommended)
Hammer
Level
Marker or pencil
Recommended Base Materials:
Solid concrete is the best base material. Brick, block, and wood stud walls may be acceptable. Metal stud walls are not an acceptable material for installation. Before installing make sure nothing is behind the wall that could be damaged by drilling and that the base material is strong enough to support a fully loaded rack. Tell your ABS Co. representative what kind of base material you are installing the Wall Rack into so the proper anchors can be shipped with the rack.
Installation:
3/8” anchors are shipped with the rack. Place the rack in the desired location. Use a marker or pencil to outline the holes of the flange onto the base material. Drill the holes in accordance with the specifications shipped with the anchors. Make sure the holes are at least 3” away from any cracks in the base material.
Tamper Resistant Fasteners:
The concrete spike is a permanent anchor. The top of the wedge anchor can also be pounded sideways after installation so that it cannot be removed. Other tamper resistant fasteners are also available for purchase.
When using the special tamper resistant nuts always set and first tighten the anchors. Once the rack is installed, replace two nuts from the bracket (opposite sides from each other) with the tamper resistant fastener. DO NOT OVERTIGHTEN the tamper resistant nut.
Page 3 of 4
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Installation Steps:
Ultra Space Saver Single
Installation
*Tools Needed for Wall Mount Installation
9/16” Wrench/Socket
3/8” Masonry Drill Bit
Tape Measure
Drill (Hammer drill recommended)
Hammer
Installation Steps:
1.
Place rack against wall. Mark holes and lower rack.
2.
Drill holes 2” deep with ½” diameter drill bit. If installing more than one Ultra Space Saver Single, mark holes for each rack individually as there may be slight differences in the placement of holes from rack to rack.
3.
Place rack back into position against wall and tap anchors through holes in the rack and into the wall.
4.
Tighten anchors
Page 4 of 4
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]

Public link updated
The public link to your chat has been updated.
Advertisement