American Bicycle Security Company Wall Rack Specifications and Assembly Instructions
Advertisement
Advertisement
Wall Rack
Use 1 or 2 U-Locks.
The Wall Rack is a secure bike hanger that hangs two bikes parallel to the wall. It was designed in cooperation with property managers who wanted to place high security bicycle hangers in individual tenants’ car parking stalls.
This rack enables property managers to provide tenants with superior bike storage without having to make separate space for dedicated bike parking. Bike owners like this option as well for garage and home storage.
The rubber coating keeps bikes from getting scratched.
Two bikes can be hung up and locked securely, as the Wall
Rack is fully u-lock compatible. The Wall Rack keeps bikes off the ground and out of the way, and provides a secure, spaceefficient way to store them.
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Wall Rack
Product
Capacity
Materials
Finishes
Installation
Methods
Space Use
& Setbacks
Wall Rack
2 Bikes
1” OD 11 gauge tube
Black Rubber Dip (plastisol)
Other colors available by special order (minimum orders apply)
Flange mount has two 3.75”x6” foot plates set 16” apart with 4 fasteners. Can be set into concrete block, solid concrete, bricks, wood studs and other base materials
When loaded with bikes, the Wall Rack will use the approximate space shown in the diagram below.
96” on center Shown
Min. 72” on center
Page 1 of 2
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Installation Steps:
Wall Rack
Installation
*Tools Needed for Installation
Tape Measure
Marker or Pencil
Masonry Drill Bit
Drill (Hammer drill recommended)
Hammer
Wrench 9/16”
Level
1.
Place the rack in the desired location. Use a marker or pencil to outline the holes of the flange onto the base material.
2.
Drill the holes in accordance with the
Recommended Base materials:
Solid concrete is the best base material for installation. To ensure the proper anchors are shipped with your rack, ask your American Bicycle representative which anchor is appropriate for your application. Be sure nothing is underneath the base material that could be damaged by drilling.
Installation:
3/8” anchors are shipped with the rack. Place the rack in the desired location. Use a marker or pencil to outline the holes of the flange onto the base material. Drill the holes in accordance with the specifications shipped with the anchors. Make sure the holes are at least 3” away from any cracks in specifications shipped with the anchors. Make sure the holes are at least 3" away from any cracks in the base material.
3.
Tap in anchors and follow your specific anchor instructions provided with the rack. the base material. Use washers to level rack if necessary. Tap in anchors and follow your specific anchor instructions provided with the rack.
Tamper Resistant Hardware
The concrete spike is a permanent anchor. The top of the wedge anchor can also be pounded sideways after installation so that it cannot be removed. Other tamper resistant fasteners are also available for purchase.
When using the special tamper resistant nuts, always set and first tighten the anchors. Once the rack is installed, replace two nuts from the bracket (opposite sides from each other) with the tamper resistant fastener.
DO NOT OVERTIGHTEN the tamper resistant nut.
Page 2 of 2
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]

Public link updated
The public link to your chat has been updated.
Advertisement