American Bicycle Security Company Air Kit 4 Specifications and Assembly Instructions
Advertisement
Advertisement
Air Kit 4
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Air Kit 4
Product
Materials
Air Kit 4
Main Body: 6” x 1/8” tube
Top: 1/8” aluminum
Manual air pump: max 100psi
Foot: ¼” steel
Standard options: Galvanized Finishes
RAL 9005
Powder Coated
Flat Black RAL 9003 RAL 2004 RAL 1023
RAL 6016
RAL 7011
RAL 6018 RAL 6005 RAL 3003 RAL 3005
RAL 7042 RAL 9007 RAL 1001 RAL 8014
Also available in Stainless Steel upon request.
Installation
Methods
Space Use
& Setbacks
Bright Yellow
Purple
Bronze
Surface Mount has 10” diameter x .25” flange with four anchoring holes for mounting with standard wedge anchors.
The Air Kit 4 should be installed at least 36” from any obstruction.
Page 1 of 5
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Air Kit 4
Tools Needed for Installation
Marker or Pencil
Masonry Drill Bit 3/8”
Drill (Hammer drill recommended)
Hammer
Wrench 9/16”
Level
Installation instructions:
Surface Mount
Recommended Base Materials:
Solid concrete is the best base material for installation. To ensure the proper anchors are shipped with your Air Kit, ask your representative which anchor is appropriate for your application. Be sure nothing is underneath the base material that could be damaged by drilling.
1. 2.
Be sure to save your tamper-resistant tools for any future maintenance.
They are costly to replace.
Place the Air Kit 4 in the desired location. Use a marker or pencil to outline the holes of the flange onto the base material.
3.
Use washers to level pump if necessary.
Drill 3/8” diameter holes 3” deep into surface. Make sure the holes are at least 3” away from any cracks in the base material.
4.
Page 2 of 5
Thread nuts onto anchors, leaving approximately 1/4” of the anchor protruding, and tap into surface. Place the 2 provided tamper-proof penta nuts on opposite sides.
Tighten nuts down to secure pump.
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Air Kit 4
1.
Maintenance & Repair
Remove the 4 tamper-proof screws at the top of the pump and lift the cap
3.
Remove the nut and carriage bolt at the top of the perforated center plate adjacent to the pump.
2.
Disconnect the airline via the push-to connect fitting at the top of the hose and at the pressure gauge.
4.
Lower the center plate to disengage the 4 tabs and slide it out of the main body.
Maintenance & Repair
Page 3 of 5
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Air Kit 4
5.
Maintenance & Repair
Continued
6.
Disconnect the airline via the push to-connect fitting at the bottom of the pump.
7.
Slide the pump sideways out of the main body slots and then lift the whole pump out of the main body.
The pump can now be taken apart without tools for servicing
Page 4 of 5
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Installation Steps:
Air Kit 4
Changing Metal Head
Remove Metal Head™ by turning counter-clockwise.
You will need a 3/4” wrench. Replace with new Metal
Head and tighten.
Page 5 of 5
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]

Public link updated
The public link to your chat has been updated.
Advertisement