American Bicycle Security Company Tool Kit Specifications and Assembly Instructions
Advertisement
Advertisement
Tool Kit
The Tool Kit includes all the necessary tools to perform routine maintenance and adjustments on most bikes.
The tools are securely fastened with stainless steel cables and tamperproof fasteners. Two versions are available, a free standing floor mount and a wall mounted version.
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Tool Kit
Tools Included:
Philips and flat head screwdrivers
2.5, 3, 4, 5, 6, 8mm Allen wrenches
Headset wrench
Pedal wrench
8, 9, 10, 11mm box wrenches
Tire levers
Product
Materials
Finishes
RAL 9005
RAL 6016
RAL 7011
RAL 3003
Installation
Methods
Space Use
& Setbacks
Tool Kit
Surface-Mounted Tool Kit
A.
Main body: 2” sch. 40 pipe
B.
Top cap: 3/16” plate
C.
Foot: 8” dia. x .25” plate
D.
Tool tethers: 5/32” stainless steel cable
Wall-Mounted Tool Kit
A.
Main body: 6.308 x .154” tube, 3/16” plate
B.
Top cap: 3/16” plate
C.
Tool tethers: 5/32” stainless steel cable
Standard options: Galvanized
Or
Powder Coated
Flat Black
RAL 6018
RAL 7042
RAL 3005
RAL 9003
RAL 6005
RAL 9007
RAL 2004
RAL 5005
RAL 1001
RAL 1023
RAL 5015
RAL 8014
Also available in Thermoplastic upon request.
Bright Yellow
Purple
Bronze
Wall Mount has a 6” dia. x 3/16” base plate that is installed onto a wall with 2 anchors.
Foot Mount has 8”x.25” circular foot with three anchors.
Surface Mount:
Wall Setback : The Tool Kit should be at least 12” from a wall.
Both sides of the Tool Kit should be 36” from either wall.
Street Setback : The Tool Kit should be at least 60” from the street.
Wall Mount :
Wall Setback: The Tool Kit should be mounted on a wall at least 54” from the ground to the center of the Tool Kit.
The Tool Kit should be 36” from an adjacent wall.
*No part of the Tool Kit should protrude onto a walkway, bike lane, or common area.
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Page 1 of 3
Tool Kit
Surface Mounted Installation
*Tools Needed for Installation
Tape Measure
Marker or Pencil
Masonry Drill Bit
Drill (Hammer drill recommended)
Hammer
Wrench 9/16”
Level
Recommended Base materials:
Solid concrete is the best base material for installation. To ensure the proper anchors are shipped with your Tool Kit, ask your Tool Kit representative which anchor is appropriate for your application. Be sure nothing is underneath the base material that could be damaged by drilling.
Standard Anchor Types
Installation:
3/8” anchors are shipped with the Tool Kit. Place the Tool Kit in the desired location. Use a marker or pencil to outline the holes of the flange onto the base material. Drill the holes in accordance with the specifications shipped with the anchors.
Make sure the holes are at least 3” away from any cracks in the base material. Use washers to level Tool Kit if necessary. Tap in anchors and follow your specific anchor instructions provided with the Tool Kit.
1. 2. 3. 4.
Tamper Resistant Hardware:
The concrete spike is a permanent anchor. The top of the wedge anchor can also be pounded sideways after installation so that it cannot be removed. Other tamper resistant fasteners are also available for purchase.
When using the special tamper resistant nuts, always set and first tighten the anchors. Once the Tool Kit is installed, replace two nuts from the Tool Kit
(opposite sides from each other) with the tamper resistant fastener. DO NOT OVERTIGHTEN the tamper resistant nut.
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Page 2 of 3
Installation Steps:
Tool Kit
Wall Mounted Installation
Instructions:
1.
The Tool Kit wall-mount should be installed with the center of the Tool Kit 54” above the ground.
2.
There are 4 mounting holes; only 2 need to be used. For installations into a vertical stud, use the 2 vertically oriented holes. The horizontally oriented holes can be used for other types of installation. 3/8” wedge anchors, lag bolts, or other fasteners may be used.
3.
Once the base is installed, place the tool cables in the slots, and fasten the cap with the provided 3/8” tamper resistant bolt.
4.
The wall guard can be mounted to prevent hanging tools from damaging the wall.
1. 2.
3. 4.
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Page 3 of 3

Public link updated
The public link to your chat has been updated.
Advertisement