Bike Depot
The Bike Haven bridges the gap between short and long term bike parking.
Starting with a simple canopy design, the design team worked to provide a solid, secure structure with full coverage. Optional polycarbonate side and back panels are available for additional protection.
The Bike Haven is available with or without racks to accommodate existing bike parking. And as demand grows, the Bike
Haven’s modular design makes it easy to add more sections.
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Bike Depot
Product
Materials
Finishes
RAL 9005
RAL 6016
RAL 7011
RAL 3003
Bike Depot
Uprights: 4” x 3/16” square tube.
Feet: 3/8” plate
Truss: 4”x1/8” square tube, 1/8” plate, ¼” plate
Purlin: 2”x4”x1/8” tube
Roof Panels: Type S deck 26g galvanized steel
Panels: 2”x2”x3/16” wire mesh, 2”x14g square tube
Standard options: Galvanized
Powder Coated
Flat Black
RAL 6018
RAL 9003
RAL 6005
RAL 2004
RAL 5005
RAL 7042
RAL 3005
RAL 9007 RAL 1001
RAL 1023
RAL 5015
RAL 8014
Bright Yellow
Purple
Bronze
Installation
Methods
Surface Mount has 10” square feet which must be anchored to the ground with supplied anchors.
Space Use
& Setbacks
Consult local building codes for acceptable setbacks and placement.
Load Data Dead load = self weight of structure
Live load = 40 psf
Wind load = 90 mph exposure B
Seismic load = moderate
Footing: See page 3
Anchors: ½” diameter x 4.25” Simpson Strong-bolt 2
Page 1 of 7
*These can also be modular.
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Bike Depot
A.
(12) 1/4” self-drill screws
B.
(4) 1/2” bolts
C.
(4) 1/2” bolts
D.
(4) 1/2” dia. Simpson strong bolt 2 anchors 3.5” min. Embedment
Parts List
1.
Upright back weldment
2.
Truss weldment
3.
Upright front weldment
4.
Purlin weldment
5.
Type s deck 2.5 x .5625
Tools needed for Installation:
Tape Measure
Level
Hammer Drill
Large Hammer
Chalk Line
Masonry Bits: 3/8”, 1/2”
Material Lift or Fork Lift
Wrenches: 9/16”, 3/4”
Socket Wrench with Sockets: 7/16”,
1/2”, 9/16”, 3/4”
Drive Socket 5/16”
Tall Ladder
Page 2 of 7
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Bike Depot
1.
Customer is responsible for preparing the slab with minimum strength of 3,000psi as shown
Installation Instructions
Main Structure
Page 3 of 7
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Bike Depot Installation Instructions
Continued
Main Structure
1.
Place uprights on concrete pad over footings (see step 1). Confirm all uprights are properly spaced and square. Using the upright foot as a template, drill (4) 1/2” diameter x 6” holes at each upright.
Install wedge anchors with nuts finger-tight. See shelter assembly drawing for specific upright placement locations. If there’s an elevation change at the uprights, a non-shrink, 3,000 psi. grout pad may be used. Longer anchors may be needed to maintain a 3.5” min. embedment.
2.
Lift trusses into place and fasten to uprights with (4) ½” x 1.5” carriage bolts,
(4) lock washers, and (4) nuts at each upright. Leave finger-tight.
3.
Install the purlins with (8) 1/2” x 5.5” bolts, (16) lock washers, and (8) nuts each. Fully tighten after all purlins are in place. Tighten all upright and truss bolts.
4.
Place the first section of type S decks and fasten with
(4) self-drilling screws to the truss. Place the next section of type S decks with 3 ridges overlapping and fasten with (4) self-drilling screws through both sections to the purlins. Each deck will provide 27.5” of coverage. Continue until done. The last section will require (8) self-drilling screws.
Page 4 of 7
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Installation Steps:
Bike Depot Installation Instructions
Continued
Panels
1.
Place a side panel in the upper position and attach with (2) 3/8” x 5.5” carriage bolts, (2) 3/8” carriage bolt washers, (2) 3/8” washers, and (2)
Penta nuts. Leave finger tight.
2.
Place a side panel in the lower position and attach with (4) 3/8” x 5.5” carriage bolts, (4) 3/8” carriage bolt washers, (4) 3/8” washers, and (4)
Penta nuts. Tighten all (6) bolts.
Place and attach the remaining side panels.
Place and attach the rear panels with the same method as the side panels.
3.
Place and attach the upper front panel in the correct position depending on whether front doors or panels are present.
Page 5 of 7
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Bike Depot Installation Instructions
Continued
4.
For shelters with front panel in place of doors, attach rear panels in the front of the shelter.
6.
Attach the doors with (1) 3/8 x 1.75” carriage bolt, (1) brass sleeve bearing, (1)
3/8” washer, and (1) Penta nut at each hinge. Tighten the Penta nuts. Then tighten hinge Penta nuts.
5.
Attach (4) hinges with (4) 3/8 x 5” carriage bolts,
(4) 3/8” carriage bolt washers, (4) 3/8” washers, and (4) Penta nuts at each hinge. If the uprights are not perfectly vertical, a washer may be placed between the hinge and upright to align the axis of the hinges. Leave the bolts finger tight.
7.
Attach both upper door stops with (2) 3/8 x 3” carriage bolts, (2) 3/8” carriage bolt washers, (2)
3/8” washers, and (2) Penta nuts at each stop.
Page 6 of 7
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
Bike Depot Installation Instructions
Continued
8.
Anchor the lower door stops to the concrete with (2)
3/8 x 3” wedge anchors and (2) Penta nuts in place of the hex nuts. The lower door stops should be directly below the upper door stops and just contact the door when it is closed. The left and right lower door stop may be placed slightly off to accommodate some distortion in the doors.
10.
Attach the door lock bar to the right door with (8) ¼ x
3” carriage bolts, (4) front door stops, (4) spacers, (8) washers, (4) tube clamps, and (8) nylock nuts. Once bolts are tightened the lock bar should rotate freely.
9.
Fill the (8) 3/8” holes in the left door with (8) ¼ x 2.5” carriage bolts, (8) lock washers, and (8) nuts.
11.
Attach the latch assembly and cover with (6) 3/8 x 1” security bolts, and (6) 3/8” washers. The latch assembly can be laterally positioned so the lock bar strike enters and exits the latch smoothly.
Page 7 of 7
American Bicycle Security Company
P.O. Box 7359
Ventura, CA 93006
Ph: (800) 245-3723 or (805) 933-3688
Fax: (805) 933-1865 www.ameribike.com
Email: [email protected]
