8

COMPACT CYLINDER VACUUM

USER GUIDE

MODEL EV-505-S16

Thank you for purchasing a BENNETT READ

FORCE 8 vacuum.

Your FORCE 8 vacuum incorporates the latest technological advances in home cleaning systems. It imitates the most powerful forces of nature in a sleek, elegant cleaning system to ensure that your home is easily and properly cleaned.

Your new vacuum is manufactured to a high standard of quality and is backed up by a 12 month guarantee by Tevo.

Should you need any support from us, please visit www.tevo.co.za or call 0861 77 88 88.

PLEASE KEEP THIS USER GUIDE IN A SAFE PLACE AND

READ IT CAREFULLY BEFORE USING YOUR BENNETT READ

FORCE 8 VACUUM FOR THE FIRST TIME.

2

IMPORTANT SAFETY INSTRUCTIONS

!

WARNING

TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK, OR INJURY:

BASIC SAFETY PRECAUTIONS

SHOULD BE OBSERVED WHEN

USING YOUR FORCE 8,

INCLUDING THE FOLLOWING:

•Your FORCE 8 is for household use only

• Use only indoors on dry surfaces

• Do not immerse any part of the system in

water or any other liquids

• Do not operate the system if the appliance

or any other part of the system has been

dropped or damaged

• Do not disassemble or attempt to repair

your FORCE 8. Return the unit for

examination and repair

• Do not use the vacuum to pick up

flammable or combustible liquids such as

gasoline and do not use it in areas where

they may be present

• Do not use the vacuum to pick up anything

that is burning or smoking such as

cigarettes, matches or hot ashes

• Use extra care when cleaning on stairs

• Do not use your FORCE 8 without the

filters in place

• Do not leave your FORCE 8 plugged in

when unattended

• Unplug the electrical cord when not in

use and before cleaning or servicing

• Keep loose clothing, hair and all parts of

body away from openings and moving

parts

• Not intended for use by persons (including

children) with reduced physical, sensory

or mental capabilities, or lack of

experience and knowledge

• Keep out of reach of children

• Do not allow your FORCE 8 to be used

as a toy

• Extra care is necessary when using your

FORCE 8 vacuum near children,

animals or plants

• Do not pull the electrical cord or use the

cord as a handle

• Take care to not close doors on the

electrical cord and do not pull the cord

around sharp edges or corners

• Do not run the vacuum over it’s own

electrical cord

• Do not allow the cord to touch hot surfaces

• Turn off all controls as applicable before

unplugging from the electrical outlet

• To unplug your FORCE 8, grasp the

plug, do not unplug by pulling on the

electrical cord

• Do not handle the plug or vacuum with

wet hands

• Do not operate your FORCE 8 while

barefoot

• Do not put any objects into the vacuum

openings

• Do not use your FORCE 8 while any

opening is blocked

• Keep your FORCE 8 free of dust, lint, hair

or anything else which may reduce airflow

• Keep your work area well lit

• Using improper voltage may result in

damage to the motor and possible injury

to the user. The correct voltage is listed

on the rating label. For operation on

220-240V, 50/60Hz power supply only

• Only use the accessories supplied with

your FORCE 8 vacuum

• Only use spare parts recommended by

Tevo

• Store your FORCE 8 indoors in a cool,

dry area

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

FOR HOUSEHOLD USE ONLY

3

20

PRODUCT VIEW

19

18

21

4

5

6

12

13

7

1

3

16

17

15

8

9

11

10

14

2

1. Multi-surface floor nozzle

2.

Brush switch

3. Extension wand (x2)

4. Tool clip holder

5. Dusting brush

6. Crevice tool

7. Air flow regulator

8. Handle

9. Hose

10. Carry handle

11. Dirt container release button

12. Hose connector

13. Suction inlet

14. Power button

15. Dirt container filter

16. Dirt container

17. Dirt container emptying

button (at the back)

18. Auto - cord rewind button

19. Post-motor filter

20. Floor nozzle storage slot

21. Power cord and plug

!

CAUTION:

Do not plug in your vacuum cleaner until you are familiar with all instructions and operating procedures.

4

ASSEMBLY

1.

Connect the hose (9) to the

vacuum by inserting the hose

connector (12) into the suction

inlet (13). You will hear a ‘click’ when

it is securely in place

2.

Attach the extension wands (3)

together by inserting one into the

other. Twist slightly to tighten the

connection

3.

Connect the hose handle (8) to the

end of the extension wand and twist

slightly to tighten

4. Connect the floor nozzle (1) to the

other end of the extension wand and

twist slightly to tighten

5. Once assembled, you can store

your vacuum by inserting the

storage clip (located on the back of

the floor nozzle) into the storage

slot (20) on the rear of the vacuum

OPERATIONS

POWER CORD

The power cord (21) is located at the rear of the vacuum. Gently pull out the power cord.

Stop pulling the cord when the yellow line is visible. There is also a red line which indicates the end of the usable cord. Do not pull the power cord out beyond the red line.

AUTO-CORD REWIND

Your vacuum is equipped with an automatic cord rewind. When cleaning is finished, press the power button OFF and grasp the plug to disconnect from the electrical outlet.

Hold the plug and press the auto-cord rewind button to rewind the cord automatically.

1.

2.

3.

4.

!

CAUTION:

The power cord retracts very quickly.

Take care to avoid injury.

Auto cord rewind

POWER BUTTON

Turn the power ON or OFF by pressing lightly downward on the power button.

5

OPERATIONS

SPECIAL TOOLS

TIP:

Your BENNETT READ FORCE 8 vacuum is not only a powerful carpet and rug cleaner, it’s also a versatile bare floor and above floor vacuum cleaner when you select one of the special tools.

Before cleaning under low furniture, check area first for objects that might harm the unit or block the hose.

FLOOR NOZZLE

Use to vacuum carpets, rugs and bare floors.

The swivel head turns to get into tight spaces and fits under cabinets

1 .

To vacuum carpets and rugs, push the

brush switch to the carpet position

CREVICE TOOL

Crevice tool

1.

Brush up

[ ]. This will pull the brushes up

into the floor nozzle.

2 . To vacuum bare floors, push the brush

switch to the bare floor position [ ].

This will extend the brushes

down from the floor nozzle.

Use the crevice tool in narrow spaces.

Dusting brush

2.

Brush down

DUSTING BRUSH

Use the dusting brush to clean curtains, draperies, cushions and fabrics.

TOOL CLIP

The tool clip provides convenient storage for your crevice tool and dusting brush when clipped onto the extension wand.

AIR FLOW REGULATOR

Tool clip

TIP:

Hair, string and small objects can block the hose and tools. Check them occasionally for obstructions.

Open the air flow regulator by sliding the regulator down towards the extension wand to an open position. This will reduce the suction power for vacuuming delicate fabrics.

For full suction power, close the air flow regulator by sliding the regulator up to the closed position.

Air flow regulator

!

WARNING:

To avoid injury, turn cleaner

OFF and unplug cord from wall when not in use.

6

MAINTENANCE AND CARE

To maintain maximum performance from your BENNETT READ FORCE 8 vacuum, perform these simple maintenance checks:

EMPTYING THE DIRT CONTAINER

Empty the dirt container as soon as the dirt reaches the “FULL” line on the sides of the dirt container.

1.

Unplug the vacuum from the

electrical outlet.

2.

Remove the hose by pressing the

securing clips inward and pulling

the hose connector out from the

suction inlet. Set the hose aside.

3.

Press the dirt container release

button under the carry handle and

lift up to remove the dirt container.

4.

Choose an emptying method.

Method #2 is recommended for

allergy sufferers.

Method #1 - Hold the dirt container

over a rubbish bin and push the

emptying button to open the

bottom. Close the bottom after the

dirt empties.

Method #2 - Place a plastic bag

over the bottom of the dirt

container. Push the emptying

button through the plastic bag to open

the bottom. After the dust settles,

close the bottom and remove the

plastic bag to discard.

5. Replace the dirt container by

placing it back into the vacuum and

pushing down on the dirt container

until it clicks back into place.

2.

3.

4.

!

WARNING:

To reduce the risk of injury from moving parts and/or electrical shock, turn Power Switch

OFF and disconnect plug from electrical outlet before performing maintenance checks.

5.

7

MAINTENANCE AND CARE

CLEANING THE DIRT

CONTAINER FILTER

The key to maximum performance is a clean filter. Cleaning the filter after each use will help your FORCE 8 vacuum operate at peak efficiency.

1. Follow the steps 1 to 4 on page 7

to remove and open the dirt

container.

2.

Unlock the dirt container filter

from the vacuum by turning it

anticlockwise. Pull the filter straight

down to remove it.

3. Remove the dirt container filter

screen by grasping the bottom of

the filter frame base and pulling the

screen straight up. Parts separate

by slowly pulling vertically upwards

on the filter screen. Do not use

excessive force.

4.

The dirt container filter screen and

dirt container filter can be hand

washed in cold water with a mild

detergent.

Rinse well and air dry

thoroughly before placing back

together.

5. Attach the dirt container filter

screen back onto the dirt container

filter by sliding it down over the dirt

container filter, making sure that

the three tabs on the top of the dirt

container filter screen line up with

the notches on the dirt container

filter.

6. Insert the dirt container filter

assembly back into the dirt

container by lining up the three

tabs on the top of the dirt container

filter assembly with the three

notches inside the top of the dirt

container and turning the dirt

container filter assembly clockwise

to lock it into place.

2.

3.

!

WARNING:

Never operate your FORCE 8 vacuum with damp or wet filters.

Dirt container filter screen

Dirt container filter

Filter frame base

!

CAUTION:

Never operate your FORCE 8 vacuum without all the filters in place. Doing so may damage the motor and void the guarantee.

8

MAINTENANCE AND CARE

CLEANING THE POST-

MOTOR FILTER

The post-motor filter assists in the filtration process to return cleaner air into the room

1.

Unplug the vacuum from the

electrical outlet.

2. Remove the filter door (located at

the back of the vacuum) by

pushing down on the tab and

pulling out and away from the

vacuum.

3. Remove the post-motor filter from

the vacuum by grasping the two

tabs and pulling gently outwards.

4.

Separate the post-motor filter

from the post-motor filter frame.

5. The post-motor filter can be hand

washed in cold water with a mild

detergent.

Rinse well and air dry

thoroughly before placing back

into the vacuum.

6.

Replace the filter door by placing

the two tabs on the bottom of the

filter door into the notches on the

bottom of the post-motor filter

compartment and pushing the tab

forward into the vacuum to lock

into place.

TIP:

For maximum cleaning performance check the filters often and clean or replace them regularly.

2.

3.

NOTICE:

This product is intended for household use only and not for commercial or industrial use.

Vacuuming of dust from products like plaster, concrete or ashes will damage the motor and void the guarantee.

!

WARNING:

Never operate your FORCE 8 vacuum with damp or wet filters, or without all filters in place.

4.

9

MAINTENANCE AND CARE

CLEARING BLOCKAGES

FROM THE DIRT CONTAINER

1.

Unplug the vacuum from the

electrical outlet.

2.

Follow steps 1 to 3 on page 7 to

remove and open the dirt container.

3. Follow steps 2 to 3 on page 8 to

remove the dirt container filter.

4.

Tap the dirt container filter

assembly over a garbage bin to

remove any dirt or debris from the

dirt container filter screen that

surrounds the dirt container.

5. Reach up into the dirt container to

clear any dirt or debris .

6.

Check if there are any blockages in

the suction inlet.

7.

After clearing any dirt or debris

from the dirt container, replace the

dirt container assembly into the dirt

container following step 7 on page 8.

!

WARNING:

To reduce the risk of electric shock, turn Power

Switch OFF and disconnect plug from electrical outlet before performing troubleshooting checks.

TROUBLESHOOTING

Problem

Vacuum cleaner won't run

Possible causes

1. Power cord not firmly plugged in

2. Power button not pressed down

Remedies

1. Check electrical plug

2. Press power button

Vacuum cleaner doesn't vacuum effectively

1. Tools, hose or extension wands

are blocked

2. Filters are dirty

3. Dirt container is full

4. Hose connector not securely

attached to suction inlet

5. Crack or hole in hose

6. Air flow regulator is set to open

or minimum setting

7. Blocked dirt container

1. Remove each part

and check for

blockages

2. Follow instructions

for cleaning filters

on pages 8 and 9

3. Follow instructions

for emptying the dirt

container on page 7

4. Check that hose

connector is locked

into suction inlet

5. Check hose and

replace if necessary

6. Change to closed or

maximum setting

7. Clear blockage from

the dirt container

following steps 1 to

7 at the top of this

page.

10

1.

TROUBLESHOOTING CONTINUED

Problem Possible causes Remedies

Dust blows out of the air vents

1. Dirt container is full

2. Filters missing or installed

incorrectly

3. Filters are dirty

1. Empty the dirt

container

2. Check all filters for

correct installation

3. Check and clean or

replace all filters

4. Hose connector is blocked 4. Remove hose and

check for blockages

5. Hose connector is not securely

attached to the suction inlet

5. Make sure the hose

connector is locked

into the suction inlet

6. Crack or hole in hose 6. Check hose and

replace if necessary

Other maintenance or service not included in the manual must be performed by an authorized Tevo service representative. For any questions or concerns, contact customer care on 0861 77 88 88.

REPLACEMENT PARTS

The items below are available for purchase as accessories for your BENNETT READ FORCE 8 vacuum. To purchase contact Tevo customer care in your area. Details on page 12.

Item Part # Part name

5.

6.

7.

8.

9.

1.

2.

3.

4.

ZHVC119CO1

HVC119CO2

Dirt container filter screen

Dirt container filter

ZHVC119CO3 Post-motor filter

ZHVC119CO4

ZHVC119CO5

ZHVC119CO6

ZHVC119CO7

ZHVC119CO8

ZHVC119CO9

Floor nozzle

Hose with handle

Extension wands (2)

Tool clip holder

Crevice tool

Dusting brush

2.

3.

4.

5.

6.

9.

7.

8.

11

CONSUMER GUARANTEE

The BENNETT READ FORCE 8 has a one year product guarantee from Tevo

(Pty) Ltd.

Tevo will replace or repair,at Tevo’s option, any defective or malfunctioning part due to manufacturing defect, free of charge from the date of purchase by the original purchaser for one year.

This guarantee applies to product used for personal or domestic use only, and specifically excludes any malfunction or defect arising from commercial use.

This guarantee does not apply to routine maintenance components such as filters and brushes. Damage or malfunction caused by negligence, abuse, unauthorized repair, or use not in accordance with the User Guide is not covered.

Tevo is not liable for incidental or consequential damages of any nature associated with the use of this product. Tevo’s liability will not exceed the purchase price of this product.

Guarantee and Service enquiries can be made by contacting:

Tevo (Pty) Ltd

Gauteng 086 111 8386

Durban (031) 570 5900

Cape Town (021) 380 0038/9

Customer Service Help Line 0861 77 88 88 www.tevo.co.za

Brought to you by:

0861 77 88 88 www.tevo.co.za | [email protected]

12