INSTALLATION MANUAL
TV Floor Cart and Accessories
9. Adjustment
|
| o
| | |
: |
y
+50 | |.
0
-10° = | = N
a N
1200mm
1250mm \
1300mm
1350mm 1
1400mm |
1450mm 4
1500mm
1550mm TV panel center
1600mm height measured =
ALL IL 1650mm \L from floor. Y)
support block
| -
Loosen the screws on both
support blocks to adjust the
DVD shelf to the desired
height then tighten all screws
to secure.
CAUTION: DO NOT EXCEED
RATED LISTED WEIGHT. SERIOUS
INJURY OR PROPERTY DAMAGE
MAY OCCUR!
Е. E) 400х400 600х400 800x400
sur. | 200x200 300x300 400x200
Y 800x600 1000x600
Maintenance
+ Check that the bracket is secure and safe to use at regular intervals(at least every three months).
« Please contact your distributor if you have any questions.
NOTE: Read the entire instruction manual before you start installation and assembly.
1«
À WARNING
e Do not begin the installation until you have read and understood all the instructions
and warnings contained in this installation sheet. If you have any questions
regarding any of the instructions or warnings, please contact your local distributor.
¢ This mounting bracket was designed to be installed and utilised ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
¢ Always use an assistant or mechanical lifting equipment to safely lift and position
the equipment.
¢ Tighten screws firmly, but do not over tighten. Over tightening can cause damage
to the items, This greatly reduces their holding power.
e This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation.
If any parts are missing or faulty, telephone your local distributor for a replacement.
middle base (x1) left cover (x1) right cover(x1)
A E
left leg (x1) right leg (x1)
B C
right column (x1)
|
top cover (x2)
L
left adapter bracket (x1)
J
right adapter bracket (x1)
K
DVD shelf (x1) camera shelf (x1)
M O
connecting plate (x1)
N
= = 7 N
2
То
y
support bar (x1) knob (x2) Меха (х2)
Р Q
ay в qu ou
M6x14 (x6)
W
M6x16 (x4) M4x6 (x3) M4x6 (x2)
S T U
— ——)
M6x25 (x2) Allen key (x1)
Y Z
M6x25 (x2)
V
(à
wrench (x1)
M8x25 (x8)
X
A1
Package M
M5x14 (x4) M6x14 (x4) M6x30 (x4) M8x30 (x4)
M-A M-B M-C M-D
M8x50 (x4) washer (x4) small spacer (x8) big spacer (x8)
M-E M-F M-G M-H
» 2
1. Assembling the Base
¢ Insert the right leg into the base. Align the holes in the right leg to the holes in the base. Secure with the
screws. Repeat this step for the left leg.
* Each caster can be adjusted independently for fine tuning. Slightly turn the nut to lower or raise the base.
2. Attaching the Column to the Base
CAUTION: Please hold the
VAN inner column when loosening I
the screws to adjust height.
TE {
. |
> Adjust to the desired height
then tighten all screws.
iE A Wi
A
—-
1—1
LUE (lil
Repeat this step for the left column.
Note: Make sure both columns are at the same height using the height indicator as guide.
3 4
A
Note: Now the columns are attached to the base without the use of any screws.
Be careful not to knock the columns over.
» 4
54
W
| 1 т y ‘ support plate
FE | | N L \
| —_ / \
© LT NY SS
> np 0 ©
| = | HH
yaw +
Insert the support plate into the column along the column
rails. Tighten all screws using a suitable screwdriver.
a
Attach the universal plate to the columns with the appropriate screws.
Tighten all screws using a Phillips screwdriver.
|
4 Use the appropriate screws to
Г ин secure the columns to the base.
Tighten all screws using an
Allen key.
f
a
eN
Tighten the safety screw.
Attach the DVD shelf to the support
bar with the appropriate screws and N
the knobs. O
» 6
supporting block
Attach the support bar (attached the DVD shelf) to
the supporting blocks with the appropriate screws. Please adjust the columns assembly to the
Tighten all screws using an Allen key. desired height before installing the display.
4. Installing the Adapter Brackets
4-1 For Flat Back Screens
74
4-2 For Recessed Back Screens or to Access A/V Inputs
Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.
" Position the adapter brackets as close as possible to the center of the display.
* Screw the adapter brackets onto the display.
Tighten all screws but do not over tighten.
5. Hanging the Display onto the Universal Plate
Hook the adapter brackets (attached the display) onto the universal plate.
Rotate the bottom screws counterclockwise to lock.
Rotate the bottom screws clockwise to unlock.
Use the padlock to prevent display from being stolen.(Padlock is not included.)
IMPORTANT: Make sure the display is correctly mounted before releasing the display.
94
6. Cable Management
_
: <> <> <> <> ав ав <> <> <> + 000000000000000000
=
a
—
0000 Doone
=
=f
| | A
Attach the camera shelf to the
connecting plate with the
appropriate screws. Tighten all
screws using a proper Phillips
I screwdriver.
8. Installing the Connecting Plate
oo,
ES EE the screws.
===)
Attach the connecting plate to the universal plate with the removed screws.
Tighten all screws using a proper Phillips screwdriver.
|
С ыы
ЧИ
» 10
">
