INSTRUCTION MANUAL
Before commencing assembly
,
please read these instructions thoroughly
.
CLIPPED WING CUB - 48
Wing Span
:
63
.
0 in /1600 mm
Wing Area
:
620 sq in / 40 sq dm
Flying Weight
:
5.5 lbs / 2500 g
Fuselage Length
:
47
.
0 in / 1200 mm
Required : 2
-
stroke 0
.
40 or 4
-
stroke 0
.
52 engine
4
-
channel radio w
/
5 servos
Warning !
This model is not a toy.
It is designed for maximum performance.
Please seek advice if one is not familiar with this kind of engine powered precision model.
Operating this model without prior preparation may cause injuries.
Remember, safety is the most important thing.
Always keep this instruction manual at hand for quick reference.
* Specifications are subject to change without notice.*
THE WINGS MAKER
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA www .
thewingsmaker .
com
GA013
CLIPPED WING CUB - 48
I N D E X
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
BEFORE YOU BEGIN
P. 1
P. 2
P.3-P.10
P. 10
1 Read through the manual before you begin , so you will have an overall idea of what to do.
2 Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly. Any parts you find to be defective after the gluing process may be difficult to remove for warranty replacement. The manufacturer will replace any defective parts. but will not extend to the parts that are good before gluing to defective parts during assembly. Warranty will not cover any parts modified by customer .
3 Symbols used throughout this instruction manual comprise of the following : -
Apply epoxy glue.
Apply instant glue
(C.A.glue, super glue.)
Assemble left and right sides the same way.
Ensure smooth non-binding movement while assembling.
Peel off shaded portion covering film.
3mm
Drill holes with the specified diameter (here: 3mm).
Cut off shaded portion.
Must be purchased separately!
Do not overlook this symbol!
Pay close attention here!
Pierce the shaded portion covering film.
Apply thread locker
P.1
Parts List
1. MAIN WING -- 1 pair
2. SCREW PWA2x12mm -- 8 pcs
PLYWOOD 2x52x80mm (For Aileron Servo) -- 1 pair
BALSA 8x18x21mm (For Aileron Servo) -- 4 pcs
3. SCREW PM2x20mm -- 4 pcs
FUEL TUBE Ø6x5mm -- 4 pcs
CLEVIS (L) -- 2 pcs
STRAPER (L) -- 2 pcs
HORN (L) -- 2 sets
PUSHROD Ø1.8x90mm w/ Threads(For Aileron) -- 2 pcs
4. PLYWOOD 2x30x120mm (Wing Protection) -- 1 pc.
WING TUBE Ø9.6x246mm -- 1 pc.
5. SCREW PM3x18mm -- 4 pcs
MAIN WING STRUTS -- 1 pair
6. FUSELAGE -- 1 pc.
VERTICAL FIN & RUDDER -- 1 set
STABILIZER & ELEVATOR -- 1 set
7. SCREW PA3x12mm -- 2 pcs
TAIL LANDING GEAR -- 1 set
TAIL WHEEL Ø25mm -- 1 pc.
COLLAR Ø2.1mm w/ set screw -- 1 set
SCREW PM2x12mm -- 1 pc.
M2 NUT -- 1 pc.
ALUMINUM PLATE 0.5mm -- 1 pc.
8. ENGINE MOUNT PL5111050 -- 1 set
SOCKET HEAD SCREW M4x25mm -- 4 pcs
WASHER d4xD9mm -- 4 pcs
9. SCREW PM3x25mm -- 4 pcs
WASHER d3xD7mm -- 8 pcs
M3 NUT -- 8 pcs
THROTTLE PUSH WIRE Ø1.2x340mm -- 1 pc.
w/ Plastic Tube d2xD3x250mm -- 1 pc.
10. FUEL TANK 260cc -- 1 set
BALSA 10x10x112mm (For Fixing Fuel Tank) -- 1 pc.
11. SCREW PM3x20mm -- 2 pcs
SCREW PA3x8mm -- 6 pcs
WASHER d3xD7mm -- 2 pcs
M3 NUT -- 2 pcs
ALUMINUM PLATE 1.5mm -- 2 pcs
MAIN LANDING GEAR -- 1 set
MOUNTING PLATE 12x20mm -- 4 pcs
12. SCREW PA1.7x8mm -- 6 pcs
MAIN WHEEL PL3112080 -- 2 sets
COLLAR Ø3.3mm w/ set screw -- 4 sets
SCREW PM2x8mm -- 6 pcs
WASHER d2xD5mm -- 6 pcs
M2 NUT -- 6 pcs
COPPER PLATE 0.5mm -- 6 pcs
BALSA 2x102x113mm (Main Landing Gear Cover) -- 1 pair
13. SCREW PWA2.3x8mm -- 4 pcs
WIND SHIELD -- 1 pc.
SILICON GROMMET d1.5x6.5mm -- 4 pcs
SIDE WINDOWS -- 1 pair
14. COWLING -- 1 pc.
TRANSPARENT DUMMY COWLING -- 1 pc.
SCREW PWA2.6x12mm -- 4 pcs
SILICON GROMMET d1.5x6.5mm -- 4 pcs
DUMMY ENGINE COVER -- 1 pair
15. LINKAGE CONNECTOR Ø2.1mm -- 1 set
16. SCREW PM2x16mm -- 7 pcs
FUEL TUBE Ø6x5mm -- 3 pcs
CLEVIS (L) -- 3 pcs
HORN (L) -- 2 sets
TRI-HORN M3x14mm (S) -- 1 set
PUSH ROD Ø1.8x725mm w/ Threads (For Rudder) -- 1 pc.
PUSH ROD Ø1.8x610mm w/ Threads (For Elevator) -- 2
17. PUSHROD Ø1.8x115mm (For Elevator) -- 1 pc.
PUSHROD CONNECTOR 4x9x20mm -- 1 set
SPONGE 70x90x105mm -- 1 pc.
PLYWOOD 3x57x115mm (For Fuselage Servos) -- 1 pc.
BALSA 6x8x108mm (For Fuselage Servos Stand) -- 2 pcs
STRAPER -- 2 pcs
FUEL TUBE Ø6x5mm -- 2 pcs
18. BALSA 3x45x108mm (For Pilot) -- 1 pc.
BALSA 6x8x45mm (For Pilot Stand) -- 2 pcs
SCREW PWA2x8mm -- 4 pcs
19. SCREW PM4x30mm -- 2 pcs
WASHER d4xD15mm -- 2 pcs
SCREW PM3x9mm -- 2 pcs
M3 NYLON INSERT LOCK NUT -- 2 pcs
20. DECALS -- 1 set
COVERING:--
TOUGHLON STL251 SKY BLUE
TOUGHLON STL312 BRIGHT RED
P.2
LIGHTEX SGX100 WHITE
1
Main Wing
Pre-glued
2
Main Wing
PWA2X12mm Screw
8
Cut away covering for installing the servo as shown.
Use the fishing line supplied inside the wing to lead the servo lead to the openings of wing center.
PWA2x12mm
Make a slot into the hatch for the servo horn to come out.
2mm
1mm
Extension lead to aileron servo.
Aileron Servo.
3
Main Wing
PM2x20mm Screw
4
Ø 1mm pilot holes for The Wings Maker tri-horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
PM2x16mm
2mm
P.3
4 Main wing
Ø9.6 x 246mm
2x30x120mm Plywood
Aluminum
Tube
5
Wing Struts
PM3x18mm Screw
4
Join the wing halves by using the aluminium tube supplied
Strengthen both holes for the screws with a piece of plywood.
558mm
189mm
95mm
PM3x18mm
Thread Locker
6
Vertical Fin / Horizontal Stabilizer
Te m p o r a r y i n s t a l l t h e m a i n w i n g , a d j u s t l e v e l i n g o f t h e s t a b i l i z e r t o m a k e i t a s p a r a l l e l t o t h e m a i n w i n g a s p o s s i b l e .
B
(Stabilizer)
B'
(Main Wing)
B=B'
90
P.4
Make sure vertical fin and stabilizer are at right angles.
7
Tail Landing Gear
PA3x12mm Screw
2
3mm Set Screw
1
2mm Collar
1
PM2x12mm Screw
1
M 2 Nut
1
3mm Set Screw
PA3 x 12mm
PM2 x 12 mm
8
Engine Mount
M4x25mm Socket Head Screw
4 d4xD9mm Washe r
4 d4xD9mm Washe r
M4x25mm
9
Engine
PM3x25mm Screw
3mm Washe r
8
M 3 Nut
8
PM3 x 25mm
Lead the 1.2mm throttle rod through the plastic tube and attach the throttle rod to the throttle lever on the engine.
Install Engine position
3mm Washer
115mm
4.53in
Fire
Wall
3mm Washer M 3 Nut
P.5
10
Fuel Tank
Fuel Tank
2 6 0 c c
Fu el
60 cc
2
Ta nk
UP
11
Main Landing Gear
PM3x20mm Screw
2
PA3x8mm Screw
6
3mm Washer
2mm
2
M3 Nut
2
PA3 x 8mm PM3x20mm
3.1mm
3mm Washer
M3 Nut
Sponge sheet
Install Balsa110x10x10mm
(For fuel tank Position fixing)
Fuel Tank
Bottom View
12
Main Landing Gear
3mm Set Screw
4
PA1.7X8mm Screw
6
Collar
4
PM2x8mm Screw
6
2mm Washer
6
M2 Nut
6
2.1mm
M2 Nut
3mm Set Screw
2mm Washer
PM2x8mm
Copper clipper
2mm Washer
PM2x8mm
PA1.7X8mm
P.6
13
Canopy
PWA2.3x8mm Screw
4 d1.5x6.5mm
Silicon Grommet
4
Securely glue the windows to the fuselage.
d1.5x6.5mm
Silicon Grommet
PWA2.3x8mm
14 Cowling
PWA2.6x12mm Screw
4 d1.5x6.5mm
Silicon Grommet
4
PWA2.6x12mm d1.5x6.5mm
Silicon Grommet
Trim the cowling for the engine head to project.
1.5mm
Please refer to the attached sheet for usage of the transparent 3D template.
15 Servo Set
3mm Set Screw
1
LINKAGE CONNECTOR
1
2mm Nut
1 d2xD5mm Washer
2
3mm
Included with the radio set.
Throttle Pushwire.
2mm
2mm
2mm
2mm
Included with the radio set.
Throttle Servo
Please refer to attached sheet for linkage connector installation.
P.7
16
Rudder&ElevatorPushrod
PM2 x 16mm Screw
7
Ø 1mm pilot holes for The Wings Maker tri-horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
Make both push rod set it as shown in the diagram.
Rudder
Tri-horn
Fuel Tube
Clevis
PM2 x 16mm
Tri-horn
3 x 14mm
Rudder
Pushrod
Elevator
Pushrod
PM2 x 16mm
Elevator
Horn
Clevis
Fuel Tube
6 x 5mm
Horn
2 m m
2 m m
Bottom View
17
Radio Equipment
Install and arrange the servos as shown in the diagram.
Elevator Servo
M2 Nut
Elevator Pushrod
Ø 1.8x115mm
Fuel Tank
Throttle Pushrod
Ø1.2x340mm
Receiver
Straper
Battery
Elevator Servo
Throttle Servo
Elevator Servo
Elevator Pushrod
Ø1.8x610mm
P.8
Fuel Tube
Ø6x5mm
Rudder Pushrod
Ø1.8x725mm
KM 2x8mm
18
Cockpit
PWA2x8mm Screw
4
1.5mm
Balsa
6 x 8 x 45mm
Balsa
3 x 45 x 110mm
19 Main Wing/Wing Struts
PM4 x 30mm Screw
4mm Washer
PM4 x 30mm Screw
2
4mm Washer
2
PM3 x 9mm Screw
2
M3 Nylon Insert Lock Nut
2
P.9
M 3 Nylon Insert Lock Nut
3mm
PM3 x 9mm
20 Wing Setting In order to obtain the wing and fuselage configuration as in the diagrams, insert reinforcement plates between the wing and fuselage if necessary.
Securely attach the main wing
C D D' C'
C = C'
D = D'
A
B B'
A'
A = A'
B = B'
21
Control Throws
Rudder
Elevator
Aileron
25mm
25mm
Adjust the control throws as shown in the diagram.
These throws are good for general flying.
You can adjust according to your personal preference.
20mm
20mm
10mm
10mm
22
C.G.
The ideal C.G. position is 70mm (2.76 in) behind
the leading edge measured at where the wing
meets the fuselage. In order to obtain the C.G.
specified, add weight to the fuselage or move
the battery position. Check the C.G. before
flying.
70mm
2.76in
P.10
www
.
thewingsmaker
.
com
Important Safety Precautions
#First time flyer should never fly by himself / herself. Assistance from experienced flyer is
absolutely necessary.
#Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly
pre-adjusted aircraft.
# CLIPPED WING CUB - 48 is specially designed to be powered by 2C 40 or 4C 52 engine, using a more powerful engine does not mean better performance. In fact, over powered engine may cause severe damage and injuries.
#Make sure the air field is spacious, never fly the plane too close to people and never get
too close to a running propeller.
#If you find wrinkles on the covering as a result of weather changes, you can use hot iron
to remove the wrinkles. Please begin with lower temperature setting and gradually raise
the temperature until the wrinkles are gone. Too hot an iron may damage the covering.
#Check and re-tighten up all factory assembled screws, use thread locker if applicable.
GA0130708
THE WINGS MAKER
P.11
