Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901
Part No. 49749
Pop Maxx
Instruction Manual
Models: 2552, 2552KC, and 2552LS
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901
SAFETY PRECAUTIONS
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901 Pop Maxx
Forward
This manual covers the 12/14 oz. Pop Maxx Popcorn Machine, model number 2552, 2552LS, 2552KC.
Installation Instructions
Inspection of Shipment:
Unpack all cartons and check thoroughly for any damage that may have occurred during transit.
Damage claims should be filed immediately with the transportation company. Gold Medal is not responsible for damage that occurs in transit.
Setup:
Your new Pop Maxx Popcorn Machine is completely assembled and tested at the factory.
Remove all packing material and tape before starting operation.
Electrical Requirements:
The following power supply must be provided:
Model No. 2552:
Model No. 2552LS:
Model No. 2552KC:
.
120 VAC, 60 Hz. 1440 Watts 12 Amps
120 VAC, 60 Hz. 1480 Watts 12.3 Amps
120 VAC, 60 Hz. 1440 Watts 12 Amps
Your electrician must furnish sufficient current for proper machine operation. We recommend this popper be on a dedicated and circuit protected line. Failure to wire properly will void the warranty and can result in damage to the heat elements, light, motor and etc.
It is Gold Medal Products Company’s recommendation that this machine be plugged directly into a wall outlet. The use of extension cords is not recommended due to safety reasons and the popper’s performance will be sacrificed/reduced.
Before You Plug In Machine:
1. Make sure that the wall outlet can accept the three (3) prong grounded plug on the power supply cord.
2. The wall outlet must have the proper polarity. If in doubt, have a competent electrician inspect the outlet and correct if necessary.
3. DO NOT use a three (3) prong grounded to two (2) prong un-grounded adapter.
3 Models #2552, #2552LS, #2552KC,
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901 Pop Maxx
Operating Instructions
Controls and Their Functions
Light & Warmer Switch
This switch operates the overhead light and corn deck freshener heat element.
Kettle Motor Switch
This switch operates the popcorn agitator shaft. This switch must be ON at all times when popcorn (popped and un-popped) is present in the kettle.
Kettle Heat Switch
This switch turns on the heat element located in the popcorn kettle.
Kettle Heat
Switch p/n 42798
Kettle Motor
Switch p/n 42532
Lights/Warmer
Switch p/n 42532
4 Models #2552, #2552LS, #2552KC,
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901 Pop Maxx
Amount of Popcorn and Oil:
Your new popper is equipped with a corn, salt, and oil measure. We recommend flavored and colored coconut oil. Popcorn popped in coconut oil stays fresh longer and does not leave black deposits in your kettle like other oils. Use only top quality fresh hybrid popcorn from reputable suppliers.
Corn charge – 12 oz./14 oz.
Oil charge – 3.5 oz./4.2 oz.
Flavacol – 14.7 cc (measure included with accessory kit)
*for best results use mega-pop premeasured pouches (item # 2839)
Popping Instructions:
1. Turn both the KETTLE HEAT and KETTLE STIR MOTOR switches ON .
2. Test pop three (3) kernels of corn and one ounce (1 Oz.) of popping oil. When the kernels pop,
the kettle is ready for use.
3. Load both a full corn/oil charge and Flavacol Seasoning Salt into the kettle. Close the lids.
4. When the corn has finished popping, gently dump the kettle.
5. Repeat the cycle, starting with step number 3, until the desired amount of popcorn has been
achieved. Always pop 3 to 5 consecutive batches for the best popcorn.
On the final kettle of corn, it is a good idea to turn the KETTLE HEAT switch OFF just as the lids are forced open by the popping corn. This procedure saves electricity since the kettle has plenty of heat and eliminates smoke/odor from any oil residue that remains after you have stopped popping.
Pappy’s Kettle Corn Instructions
1. Turn kettle heat, stir motor, and lights to the ON position
2. First Batch Online: pre-heat kettle for 4 minutes.
3. Add 3/8 part oil and 1 part popcorn into the kettle (No Salt!). Start timer for 45-60 seconds.
4. Add 2/3 part Pappy’s into kettle when timer goes off. If popping has just started, close the right door and carefully/quickly add the Pappy’s mix through the left door. Re-open right door.
5. Dump Kettle when popping has nearly stopped, repeat steps 3 and 4. Salt and mix the popped corn thoroughly. Pop at least 5 batches.
5 Models #2552, #2552LS, #2552KC,
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901 Pop Maxx
Count Down timer Instructions
1. Press MIN and SEC together to reset timer to zeo.
2. Use MIN and SEC buttons to set time.
3. Press START button to start or stop.
4. The alarm will sound for 60 seconds or press any key to stop alarm. The timer will return to the set time.
5. Timer part number - 63012
6 Models #2552, #2552LS, #2552KC,
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901 Pop Maxx
Care And Cleaning
After completion of a series of popping, wipe the outside of the kettle with a soft cloth to remove any oil drippings/residue. DO NOT let this residue burn on! After completion of popping for the day, let the kettle cool until it is warm to the touch. Unplug the kettle and remove from machine. Use a soft cloth to wipe out the inside of the kettle, kettle lids, kettle crossbar, agitator and all outside surfaces of the kettle.
DO NOT immerse the kettle in water, or any other cleaning solution, this will void the warranty.
It is recommended, as a routine maintenance procedure, to use authentic Gold Medal Products
Company 2095 Heat’n Kleen inside kettle cooking surface cleaner. Heat’n Kleen will remove any oily build-up, and helps maintain a clean cooking surface, if used on a routine basis. Heat’n Kleen will not damage the kettle’s cook surface. Contact your local Gold Medal Products Company dealer if additional cleaning strength is required for extremely dirty kettles.
For fresh corn tomorrow, remove all popped popcorn and place in a clean sealed food container.
The container must be suitable for direct food contact.
Clean the glass and all interior/exterior cabinet surfaces using Gold Medal’s non-ammonia watchdog glass cleaner – item #2588. A regularly cleaned machine is easier to keep clean. In addition, a clean machine is more appealing to both customers and increases sales. Your local food service inspectors appreciate a clean machine.
NOTE: DO NOT use any cleaners that contain ammonia. Ammonia based cleaners may crack and/or fog the plastic parts/doors on the machine.
7 Models #2552, #2552LS, #2552KC,
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901 Pop Maxx
Filter Cleaning Instructions
Your popcorn machine is equipped with an efficient and durable filtration system. However, the filter should be cleaned every 1-2 weeks to maintain efficiency. Follow the steps below for proper filter cleaning:
1. The filter is located on the inside of the popcorn machine, directly above the popping kettle.
2.
Remove the filter by gripping the filter itself, and pulling straight down. (As shown below.)
1. Clean the filter in warm soapy water, and allow to dry overnight. Replace the filter by putting it into the slot, and pushing upward. (As shown below) Make sure the filter frame is flush with the roof of the machine. (As shown above)
8 Models #2552, #2552LS, #2552KC,
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901
MAINTENANCE INSTRUCTIONS
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901
ORDERING SPARE PARTS
*
Always speak to a Gold Medal Products Technical Service Advisor before ordering any parts to help ensure accuracy for your product. Included diagrams may not be the latest information.
1. Identify the needed part by checking it against the photos, illustrations, and/or parts list.
2. When ordering, please include part number, part name, and quantity needed.
3. Please include your model name, serial number, and date of manufacture (located on the machine nameplate) with your order.
4. Address all parts orders to:
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
Or, place orders by phone or online:
(800) 543-0862
(513) 769-7676
Fax: (513) 769-8500
E-mail:
Web Page:
www.gmpopcorn.com
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901 Pop Maxx
Kettle Breakdown Kettle Complete – P/N 58014
Twist Lock Plug (Plug Only) p/n 49329
Dump Handle Knob p/n 47110
Dump Handle Assy p/n 49571
Lead-in Cord Assy.
Complete p/n 61053
Kettle Shell Assy. p/n 61017
Thermostat Shunt Bar p/n 47193
Thermostat 482F - 76708
(For 2552KC - Thermostat
450F p/n 76089)
Kettle with Bonded-On
Heat Elements p/n 58012
Kettle Gasket p/n 61012
Thermostat 550F High limit -
77108
(For 2552KC - Thermostat
525F p/n 76702)
11 Models #2552, #2552LS, #2552KC,
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901 Pop Maxx
Bearing Hub (Included with 41093 shaft assy.) p/n 43434
Spur Gear p/n 47060
Set Screw for Spur
Gear p/n 41742
Set Collar (3) p/n 46649
Set Screws for Set
Collars (2) p/n 47751
Front Kettle Lid p/n 41123
Crossbar Assy. p/n 58015
Lid and Agitator Assembly
Needle Bearing p/n 47106
Agitator Shaft Assy.
(Includes 43434
Bearing Hub) p/n 69712
Rear Kettle Lid p/n 41120
Stir Rod p/n 69806
Lid and Agitator Assembly available complete as P/N 58016
12 Models #2552, #2552LS, #2552KC,
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901 Pop Maxx
Cabinet Assembly
Magnetic Catch p/n 47561
Bracket for Magnetic Catch p/n 41340
Dome p/n 77769
Glass (3 pieces – same size) p/n 49826
Dimensions:
16 7/8” X 21 ¼”
Door Knob p/n 47120 (If Black Plastic)
Door Knob p/n 41013 (If Silver Metal)
Screw for Knob p/n 42044
Female Hinge – Left (2) p/n 41352 (On Door)
Male Hinge – Left (2) p/n 41349 (On Cabinet)
Door (2) p/n 77774
Label p/n 47663
Old Maid Pan p/n 49100
Knob p/n 47120 Drop Panel p/n 77730
Magnet p/n 51113
Screw for Magnet p/n 75267
Female Hinge – Right (2) p/n 41351 (On Door)
Male Hinge – Right (2) p/n 41350 (On Cabinet)
Corn Pan p/n 77778
Label p/n 49393
Power Supply Cord 15
Amp p/n 87085
13 Models #2552, #2552LS, #2552KC,
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901 Pop Maxx
Small Switch Box p/n 48501
Box Filter p/n 69850
(5x10x2)
Switch Box Label p/n 48502
Spur Gear p/n 47060
Set Screw for
Spur Gear p/n 41742
Magnetic Catch p/n 47561
Magnetic Catch
Bracket p/n 41340
50 W Flood Light
(Coated) p/n 42947
Front Hanger Arm p/n 61049
Gear Block Assy p/n 67194NM
12 oz Unimaxx Kettle
Complete p/n 58014
Kettle Lead Assy p/n 62308
Kettle Receptacle p/n 49330
Rear Hanger Arm Assy. – with Dump Pin p/n 61050
Lighted Sign Components for Model 2552LS Only:
Light Tube Holder: 41020
Light tube Holder Starter: 41021
Light Ballast 120V: 41022
Light Starter: 41023
L ight Tube: 41057
14 Models #2552, #2552LS, #2552KC,
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901 Pop Maxx
20 Watt Foil Heater
(Under Bottom Cover) p/n 40557
Motor Plate Assembly
Exhaust Blower (2) p/n 48018
Light Shield
Conical p/n 40589
Lamp Holder p/n 47047
Kettle Receptacle p/n 49330
Kettle Drive Motor p/n 47038
Terminal block p/n 47208
15 Models #2552, #2552LS, #2552KC,
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901 Pop Maxx
Electrical Schematic
16 Models #2552, #2552LS, #2552KC,
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901
WARRANTY
WE WARRANT to the original purchaser the Gold Medal equipment sold by us to be free from defects in material or workmanship under normal use and service. Our obligation under this warranty shall be limited to the repair or replacement of any defective part for a period of six (6) months from the date of sale to the Original
Purchaser with regard to labor and two (2) years with regard to parts and does not cover damage to the equipment caused by accident, alteration, improper use, voltage, abuse, or failure to follow instructions.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED
OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR
PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF. We neither assume, nor authorize any other person to assume for us, any other obligation or liability in connection with the sale of said
GOLD MEDAL equipment or any part thereof.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that person, firm, association, or corporation who was billed by the GOLD MEDAL
PRODUCTS COMPANY, or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS COMPANY AT 1-800-
543-0862 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE
EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS
CONCERNING THE REPAIR OR REPLACEMENT OF PARTS.
GOLD MEDAL PRODUCTS COMPANY
10700 Medallion Drive
Cincinnati, Ohio 45241-4807 USA www.gmpopcorn.com
Phone: 1-800-543-0862
Fax: 1-800-542-1496
© The text, descriptions, graphics and other material in this publication are the proprietary and exclusive property of Gold Medal Products Company and shall not be used, copied, reproduced, reprinted or published in any fashion, including website display, without its express written consent.
