WL-366
WL-366
Wireless Broadband Router
(802.11b/g/n)
User Manual
Revision: 1
TABLE
OF
CONTENTS
1KEY FEATURES...................................................................................................................................4
2PACKAGE CONTENTS......................................................................................................................5
3PRODUCT LAYOUT............................................................................................................................6
4NETWORK + SYSTEM REQUIREMENTS.....................................................................................8
5WL-366 PLACEMENT.........................................................................................................................8
6SETUP LAN, WAN................................................................................................................................9
7PC NETWORK ADAPTER SETUP.................................................................................................10
8BRINGING UP THE WL-366............................................................................................................14
9 INITIAL SETUP WL-366..................................................................................................................14
10 CONFIGURATION WIZARD........................................................................................................22
11 WIRELESS SETTINGS...................................................................................................................24
12 FIREWALL SETTINGS..................................................................................................................35
13 ADVANCED SETTINGS................................................................................................................41
14 TOOLBOX SETTINGS..................................................................................................................47
2
Introduction
Congratulations on your purchase of the WL-366 Wireless Network Broadband
Router. The WL-366 is compliant with 802.11n v2.0 and up to 6 times faster
than standard 802.11g based routers while still being compatible with 802.11g
& 802.11b devices. The WL-366 is not only a Wireless Access Point, but also
doubles as a 4-port full-duplex Switch that connects your wired-Ethernet
devices together.
At 300 Mbps wireless transmission rate, the Access Point built into the Router
uses advanced MIMO (Multi-Input, Multi-Output) technology to transmit
multiple streams of data in a single wireless channel, giving you seamless
access to multimedia content. Robust RF signals travel farther, eliminating dead
spots and extending network range. For data protection and privacy, the WL366 encodes all wireless transmissions with WEP, WPA, or WPA2 encryption.
With an inbuilt DHCP Server & powerful SPI firewall the WL-366 protects your
computers against intruders and most known Internet attacks but provides safe
VPN pass-through. With the incredible speed and the QoS function of 802.11n,
the WL-366 is ideal for media-centric applications like streaming video, gaming,
and VoIP telephony to run multiple media-intense data streams through the
network at the same time, with no degradation in performance.
3
1
Key Features
Features
Advantages
Incredible Data Rate up to
Heavy data payloads such as
300Mbps*
MPEG video streaming
IEEE 802.11n draft 2.0 Compliant
Fully Interoperable with IEEE
and backward compatible with
802.11b / IEEE802.11g
802.11b/g
compliant devices with legacy
protection
Four 10/100 Mbps Fast Switch Ports
Scalability, extend your
(Auto-Crossover)
network.
Firewall supports Virtual Server
Avoids the attacks of Hackers
Mapping, DMZ, IP Filter, ICMP
from Internet.
Blocking, SPI.
Support 802.1x authenticator,
Provide mutual authentication
802.11i (WPA/WPA2, AES), VPN
(Client and dynamic encryption
pass-through
WDS (Wireless Distribution
keys to enhance security)
Make wireless AP and Bridge
System)
mode simultaneously as a
wireless repeater.
* Theoretical wireless signal rate based on IEEE standard of 802.11a, b, g, n chipset used.
Actual throughput may vary. Network conditions and environmental factors lower actual
throughput rate. All specifications are subject to change without notice.
4
2
Package Contents
Open the package carefully, and make sure that none of the items listed below
are missing. Do not discard the packing materials, in case of return; the unit
must be shipped back in its original package.
1.
WL-366 Router
2.
220V~240V Power Adapter
3.
Quick Install Guide
4.
CD (User’s Manual)
5.
Warranty card
6.
UTP cable
5
3
Product Layout
Port
Description
Power connector
Connect the DC adapter here.
WAN[Blue]
LAN[Yellow]
Connect the cable from your ADSL/Cable modem
to this port.
Connect the cable from your PC’s or network
devices to this port.
6
Back label
The back label describes the corresponding LED indications and port
functionality.
LED
Description
Lights up in yellow when WLAN is enabled, blinks
WLAN
yellow when WPS is set and lights up blue when
LINK/ACTIVY
WLAN is connected.
Blinks on traffic for specific LAN PORT
Lights up in yellow when WAN port is connected,
WAN
lights up in blue when internet connection is
established.
Press 2 seconds for WPS mode
WPS BUTTON
Press 10 seconds to reset the router
Press 15 seconds to reset the router to factory
defaults.
7
4
Network + System Requirements
To begin using the WL-366, make sure you meet the following as minimum
requirements:
•
PC/Notebook.
•
Operating System – Microsoft Windows XP/2000/VISTA/7.
•
1 Free Ethernet port.
•
WiFi card/USB dongle (802.11 b/g/n) – optional.
•
External xDSL (ADSL) or Cable modem with an Ethernet port (RJ-45).
•
PC with a Web-Browser (Internet Explorer, Safari, Firefox, Opera).
•
Ethernet compatible CAT5 cables.
5
WL-366 Placement
You can place the WL-366 on a desk or other flat surface, or you can mount it on a
wall. For optimal performance, place your Wireless Broadband Router in the center
of your home (or your office) in a location that is away from any potential source of
interference, such as a metal wall or microwave oven. This location must be close
to a power connection and your ADSL/Cable modem.
8
6
Setup LAN, WAN
WAN connection:
LAN connection:
9
7
PC Network Adapter setup
Windows XP
•
Enter [Start Menu]  select [Control panel]  select [Network].
•
Select [Local Area Connection]) icon=>select [properties]
10
•
Select [Internet Protocol (TCP/IP)] =>Click [Properties].
•
Select the [General] tab.
a. The router supports [DHCP] function, please select both [Obtain an IP
address automatically] and [Obtain DNS server address automatically].
11
Windows Vista/7
•
Enter [Start Menu]  select [Control panel]  select [View network status
and tasks] -> select [Manage network connections].
•
Select [Local Area Connection]) icon=>select [properties]
12
•
Select [Internet Protocol Version 4 (TCP/IPv4)] =>Click [Properties].
•
Select the [General] tab.
The router supports [DHCP] function, please select both [Obtain an IP address
automatically] and [Obtain DNS server address automatically].
13
8
Bringing up the WL-366
Connect the supplied power-adapter to the power inlet port and connect it to a
wall outlet. The router automatically enters the self-test phase. During self-test
phase, the Power LED will be lit continuously to indicate that this product is in
normal operation.
9
Initial Setup WL-366
LOGIN procedure
1. Click to OPEN your browser (e.g. Internet Explorer).
14
2. Type http://192.168.0.1 in the address bar and press [Enter].
15
3. Type user name and password (default is admin/admin).
4. Click OK.
5. You will see the home page of the WL-366.
The System status section allows you to monitor the current status of your
router.
The UP time, hardware information, serial number as well as firmware
version information is displayed here.
16
DHCP Server
The DHCP server tab gives you the opportunity to change the IP settings of the
WL-366.
IP address 192.168.0.1. It is the router’s LAN IP address (Your LAN clients
default gateway IP address).
IP Subnet Mask 255.255.255.0 Specify a Subnet Mask for your LAN segment.
DHCP Server Enabled by default. You can enable or disable the DHCP server.
When DHCP is disabled no ip-addresses are assigned to clients and you have to
use static ip-addresses. When DHCP server is enabled your computers will be
assigned an ip-address automatically until the lease time expires.
Lease Time Forever. In the Lease Time setting you can specify the time period
that the DHCP lends an IP address to your LAN clients. The DHCP will change
your LAN client’s IP address when this time threshold period is reached.
17
Start IP/End IP You can select a particular IP address range for your DHCP
server to issue IP addresses to your LAN Clients.
Note: default IP range 192.168.0.100  192.168.0.199. If you want
your PC(s) to have a static/fixed IP address, then you’ll have to choose
an IP address outside this IP address Pool
Domain Name You can specify a Domain Name for your LAN. Or just keep the
default (SitecomWLxxx).
Click <Apply> at the bottom of this screen to save any changes.
Device Status
View the Broadband router’s current configuration settings. Device Status
displays the configuration settings you’ve configured in the Wizard / Basic
Settings / Wireless Settings section.
18
Internet Status
This page displays whether the WAN port is connected to a Cable/DSL
connection. It also displays the router’s WAN IP address, Subnet Mask, and ISP
Gateway as well as MAC address, the Primary DNS. Press Renew button to
renew your WAN IP address.
19
DHCP Client Status
This page shows all DHCP clients (LAN PCs) currently connected to your
network. The table shows the assigned IP address, MAC address and expiration
time for each DHCP leased client. Use the Refresh button to update the
available information.
20
WL-366 Log
View the operation log of the WL-366. This page shows the current system log
of the Broadband router. It displays any event occurred after system start up.
At the bottom of the page, the system log can be cleared <Clear> or it can be
refreshed <Refresh> to get the most updated information. When the system
is powered down, the system log will disappear.
21
10
Configuration Wizard
Click Wizard to configure the router. The Setup wizard will now be displayed;
check that the modem is connected and click Next.
Select your country from the Country list. Select your internet provider. Click
Next.
22
Depending on the chosen provider, you may need to enter your user name and
password, MAC address or hostname in the following window. After you have
entered the correct information, click Next.
Click APPLY to complete the configuration.
23
11
Wireless Settings
You can set parameters that are used for the wireless stations to connect to this
router. The parameters include Mode, ESSID, Channel Number and Associated
Client.
Wireless Function
Enable or Disable Wireless function here. Click Apply and wait for module to
be ready & loaded.
24
Basic Settings
Mode Allows you to set the AP to AP or WDS mode.
802.11 Mode Allows you to set the AP fixed at 802.11b or 802.11g mode. You
can also select B+G mode to allow 802.11b and 802.11g clients at the same
time.
Band Allows you to choose the channel bandwidth 20 MHz or 20/40 MHz.
ESSID This is the name of the wireless signal which is broadcasted. All the
devices in the same wireless LAN should have the same ESSID.
Channel The channel used by the wireless LAN. All devices in the same
wireless LAN should use the same channel.
Extension Channel Allows you to select the extension channel when Channel
bandwidth is set to 20/40 MHz.
25
Advanced Settings
This tab allows you to set the advanced wireless options. The options included
are Authentication Type, Fragment Threshold, RTS Threshold, Beacon Interval,
and Preamble Type. You should not change these parameters unless you know
what effect the changes will have on the router.
Fragment Threshold "Fragment Threshold" specifies the maximum size of a
packet during the fragmentation of data to be transmitted. If you set this value
too low, it will result in bad performance.
RTS Threshold When the packet size is smaller then the RTS threshold, the
wireless router will not use the RTS/CTS mechanism to send this packet.
Beacon Interval is the interval of time that this wireless router broadcasts a
beacon. A Beacon is used to synchronize the wireless network.
Broadcast ESSID If you enabled “Broadcast ESSID”, every wireless station
located within the coverage of this access point can discover this access point
easily. If you are building a public wireless network, enabling this feature is
recommended. Disabling “Broadcast ESSID” can provide better security.
26
Preamble Type The “Long Preamble” can provide better wireless LAN
compatibility while the “Short Preamble” can provide better wireless LAN
performance.
WMM WiFi Multi Media if enabled supports QoS for experiencing better audio,
video and voice in applications.
27
Security
This Access Point provides complete wireless LAN security functions, included
are WEP and WPA with pre-shared key. With these security functions, you can
prevent your wireless LAN from illegal access. Please make sure your wireless
stations use the same security function, and are setup with the same security
key.
Disable
When you choose to disable encryption, it is very insecure to operate the WL366.
28
WEP
When you select 64-bit or 128-bit WEP key, you have to enter WEP keys to
encrypt data. You can generate the key by yourself and enter it. You can
enter four WEP keys and select one of them as a default key. Then the router
can receive any packets encrypted by one of the four keys.
Key Length You can select the WEP key length for encryption, 64-bit or 128bit. The larger the key will be the higher level of security is used, but the
throughput will be lower.
Key Type You may select ASCII Characters (alphanumeric format) or
Hexadecimal Digits (in the "A-F", "a-f" and "0-9" range) to be the WEP Key.
Key1 - Key4 The WEP keys are used to encrypt data transmitted in the
wireless network. Use the following rules to setup a WEP key on the device.
64-bit WEP: input 10-digits Hex values (in the "A-F", "a-f" and "0-9" range) or
5-digit ASCII character as the encryption keys. 128-bit WEP: input 26-digit
Hex values (in the "A-F", "a-f" and "0-9" range) or 13-digit ASCII characters
as the encryption keys.
29
Click <Apply> at the bottom of the screen to save the above configurations.
You can now configure other sections by choosing Continue, or choose Apply
to apply the settings and reboot the device.
30
WPA Pre-shared Key
Wi-Fi Protected Access (WPA) is an advanced security standard. You can use a
pre-shared key to authenticate wireless stations and encrypt data during
communication. It uses TKIP or CCMP (AES) to change the encryption key
frequently. So the encryption key is not easy to be cracked by hackers. This is
the best security available.
31
ACL
This wireless router supports MAC Address Control, which prevents
unauthorized clients from accessing your wireless network.
Enable wireless access control Enables the wireless access control function
Adding an address into the list Enter the "MAC Address" of the wireless
station to be added and then click "Add". The wireless station will now be added
into the "MAC Address Filtering Table" below.
Remove an address from the list If you want to remove a MAC address from
the "MAC Address Filtering Table", select the MAC address that you want to
remove in the list and click “Delete”.
Click <Apply> at the bottom of the screen to save the above configurations.
32
WPS
Wi-Fi Protected Setup (WPS) is the simplest way to establish a connection
between the wireless clients and the wireless router. You don’t have to select
the encryption mode and fill in a long encryption passphrase every time when
you try to setup a wireless connection. You only need to press a button on both
wireless client and wireless router, and WPS will do the rest for you.
The wireless router supports two types of WPS: WPS via Push Button and WPS
via PIN code. If you want to use the Push Button, you have to push a specific
button on the wireless client or in the utility of the wireless client to start the
WPS mode, and switch the wireless router to WPS mode. You can simply push
the WPS button of the wireless router, or click the ‘Start to Process’ button in
the web configuration interface. If you want to use the PIN code, you have to
know the PIN code of the wireless client and switch it to WPS mode, then fill-in
the PIN code of the wireless client through the web configuration interface of
the wireless router.
WPS Check the box to enable WPS function and uncheck it to disable the WPS
function.
33
WPS Current Status If the wireless security (encryption) function of this
wireless router is properly set, you’ll see a ‘Configured’ message here.
Otherwise, you’ll see ‘UnConfigured’.
WPS Passphrase It shows the passphrase key that is randomly generated by
the wireless router during the WPS process. You may need this information
when using a device which doesn’t support WPS.
SSID This is the network broadcast name (SSID) of the router.
Authentication Mode It shows the active authentication mode for the wireless
connection.
WPS via Push Button Press the button to start the WPS process. The router
will wait for the WPS request from the wireless devices within 2 minutes.
WPS via PIN You can fill-in the PIN code of the wireless device and press the
button to start the WPS process. The router will wait for the WPS request from
the wireless device within 2 minutes.
34
12 Firewall Settings
The Broadband router provides extensive firewall protection by restricting
connection parameters, thus limiting the risk of hacker attacks, and defending
against a wide array of common Internet attacks. However, for applications that
require unrestricted access to the Internet, you can configure a specific
client/server as a Demilitarized Zone (DMZ).
Note: To enable the Firewall settings select Enable and click Apply
35
DMZ
If you have a client PC that cannot run an Internet application (e.g. Games)
properly from behind the NAT firewall, then you can open up the firewall
restrictions to unrestricted two-way Internet access by defining a DMZ Host.
The DMZ function allows you to re-direct all packets going to your WAN port IP
address to a particular IP address in your LAN. The difference between the
virtual server and the DMZ function is that the virtual server re-directs a
particular service/Internet application (e.g. FTP, websites) to a particular LAN
client/server, whereas DMZ re-directs all packets (regardless of services) going
to your WAN IP address to a particular LAN client/server.
Enable DMZ Enable/disable DMZ
Host Enter the IP address of a particular host in your LAN that will receive all
the packets originally going to the WAN port/Public IP address above.
Click <Apply> at the bottom of the screen to save the above configurations.
36
Denial of Service (DoS)
The Broadband router's firewall can block common hacker attacks, including
Denial of Service, Ping of Death, Port Scan and Sync Flood. If Internet attacks
occur the router can log the events.
Discard Ping on WAN The router’s WAN port will not respond to any Ping
requests.
37
Access
You can restrict users from accessing certain Internet applications/services
(e.g. Internet websites, email, FTP etc.), Access Control allows users to define
the traffic type permitted in your LAN. You can control which PC client can have
access to these services.
Deny If you select “Deny” then all clients will be allowed to access Internet
accept for the clients in the list below.
Allow If you select “Allow” then all clients will be denied to access Internet
accept for the PCs in the list below.
Filter client PCs by IP Fill in “IP Filtering Table” to filter PC clients by IP.
Add PC You can click Add PC to add an access control rule for users by IP
addresses.
Remove PC If you want to remove some PCs from the "IP Filtering Table",
select the PC you want to remove in the table and then click “Delete
Selected". If you want to remove all PCs from the table, just click the "Delete
All" button.
Filter client PC by MAC Check “Enable MAC Filtering” to enable MAC
Filtering.
Add PC Fill in “Client PC MAC Address” and “Comment” of the PC that is
allowed to access the Internet, and then click “Add”. If you find any typo
before adding it and want to retype again, just click "Reset" and the fields will
be cleared.
38
Remove PC If you want to remove some PC from the "MAC Filtering Table",
select the PC you want to remove in the table and then click "Delete
Selected". If you want to remove all PCs from the table, just click the "Delete
All" button. If you want to clear the selection and re-select again, just click
“Reset”.
Click <Apply> at the bottom of the screen to save the above configuration.
39
URL block
You can block access to some Web sites from particular PCs by entering a full
URL address or just keywords of the Web site.
Enable URL Blocking Enable/disable URL Blocking
Add URL Keyword Fill in “URL/Keyword” and then click “Add”. You can enter
the full URL address or the keyword of the web site you want to block.
Remove URL Keyword If you want to remove some URL keywords from the
"Current URL Blocking Table", select the URL keyword you want to remove in
the table and then click "Delete Selected". If you want remove all URL keywords
from the table, just click "Delete All" button. If you want to clear the selection
and re-select again, just click “Reset”.
Click <Apply> at the bottom of the screen to save the above configurations
40
13 Advanced Settings
Network Address Translation (NAT) allows multiple users at your local site to
access the Internet through a single Public IP Address or multiple Public IP
Addresses. NAT provides Firewall protection from hacker attacks and has the
flexibility to allow you to map Private IP Addresses to Public IP Addresses for
key services such as Websites and FTP. Select Disable to disable the NAT
function.
Virtual Server
Use the Virtual Server function when you want different servers/clients in your
LAN to handle different service/Internet application type (e.g. Email, FTP, Web
server etc.) from the Internet. Computers use numbers called port numbers to
recognize a particular service/Internet application type. The Virtual Server
allows you to re-direct a particular service port number (from the Internet/WAN
Port) to a particular LAN private IP address and its service port number.
Enable Enable Virtual Server.
41
Local IP This is the LAN client/host IP address that the Public Port number
packet will be sent to.
Local Port This is the port number (of the above Private IP host) that the
below Public Port number will be changed to when the packet enters your
LAN (to the LAN Server/Client IP)
Type Select the port number protocol type (TCP, UDP or both). If you are
unsure, then leave it to the default “both” setting. Public Port Enter the
service (service/Internet application) port number from the Internet that will
be re-directed to the above Private IP address host in your LAN
Comment The description of this setting.
Add Virtual Server Fill in the "Local IP", "Local Port", "Type", “Public
Port” and "Comment" of the setting to be added and then click "Add". Then
this Virtual Server setting will be added into the "Current Virtual Server Table"
below.
Remove Virtual Server If you want to remove Virtual Server settings from
the "Current Virtual Server Table", select the Virtual Server settings you want
to remove in the table and then click "Delete Selected". If you want to
remove all Virtual Server settings from the table, just click the "Delete All"
button. Click "Reset" will clear your current selections.
Click <Apply> at the bottom of the screen to save the above configurations.
42
Special Applications
Some applications require multiple connections, such as Internet games, video
Conferencing, Internet telephony and others. In this section you can configure
the router to support multiple connections for these types of applications.
Trigger Port This is the out going (Outbound) range of port numbers for this
particular application.
Trigger Type Select whether the outbound port protocol is “TCP”, “UDP” or
both.
Public Port Enter the In-coming (Inbound) port or port range for this type of
application (e.g. 2300-2400, 47624)
Public Type Select the Inbound port protocol type: “TCP”, “UDP” or both
Enable Trigger Port Enable the Special Application function.
43
Popular applications This section lists the more popular applications that
require multiple connections. Select an application from the Popular
Applications selection. Once you have selected an application, select a location
(1-10) in the Copy to selection box and then click the Copy to button. This will
automatically list the Public Ports required for this popular application in the
location (1-10) you specified.
44
UPnP
With UPnP, all PCs in you Intranet will discover this router automatically. So,
you don’t have to configure your PC and it can easily access the Internet
through this router.
UPnP You can enable or Disable the UPnP feature here. After you enable the
UPnP feature, all client systems that support UPnP, like Windows XP, can
discover this router automatically and access the Internet through this router
without having to configure anything. The NAT Traversal function provided by
UPnP can let applications that support UPnP connect to the internet without
having to configure the virtual server sections.
45
QoS
QoS can let you classify Internet application traffic by source/destination IP
address and port number. You can assign priority for each type of application
and reserve bandwidth for it. The packets of applications with higher priority
will always go first. Lower priority applications will get bandwidth after higher
priority applications get enough bandwidth. This can let you have a better
experience in using critical real time services like Internet phone, video
conference …etc. All the applications not specified by you are classified as rule
name “Others”. The rule with a smaller priority number has a higher priority;
the rule with a larger priority number has a lower priority. You can adjust the
priority of the rules by moving them up or down.
Enable/Disable QoS You can check “Enable QoS” to enable QoS functionality
for the WAN port.
Traffic mapping Click “Add traffic class” then enter a form of the QoS rule. Click
“Apply” after filling out the form the rule will be added into the table.
Edit a QoS rule Select the rule you want to edit and click “Edit”, then enter the
detail form of the QoS rule. Click “Apply” after editing the form and the rule will
be saved.
Adjust QoS rule priority. You can select the rule and click “Move Up” to make
its priority higher. You also can select the rule and click “Move Down” to make
its priority lower.
46
14
TOOLBOX Settings
Password change options
You can change the password required to log into the broadband router's
system web-based management. By default, the password is: admin.
Passwords can contain 0 to 12 alphanumeric characters, and are case sensitive.
Current Password Fill in the current password to allow changing to a new
password.
New Password Enter your new password
Confirmed Password Enter your new password again for verification purposes
Click <Apply> at the bottom of the screen to save the above configurations
47
Time Zone
The Time Zone allows your router to base its time on the settings configured
here, which will affect functions such as Log entries and Firewall settings.
Set Time Zone Select the time zone of the country you are currently in. The
router will set its time based on your selection.
Time Server Address You can set an NTP server address.
Enable Daylight Savings The router can also take Daylight savings into
account. If you wish to use this function, you must check/tick the enable box
to enable your daylight saving configuration (below).
Click <Apply> at the bottom of the screen to save the above configurations.
48
Remote Management
The remote management function allows you to designate a host in the Internet
the ability to configure the Broadband router from a remote site. Enter the
designated host IP Address in the Host IP Address field.
Host Address This is the IP address of the host in the Internet that will have
management/configuration access to the Broadband router from a remote site.
If the Host Address is left 0.0.0.0 this means anyone can access the router’s
web-based configuration from a remote location, providing they know the
password.
Port The port number of the remote management web interface.
Enable Select “Enable” to enable the remote management function.
Click <Apply> at the bottom of the screen to save the above configurations.
49
Firmware Upgrade
This page allows you to upgrade the router’s firmware.
Firmware Upgrade This tool allows you to upgrade the Broadband router’s
system firmware. To upgrade the firmware of your Broadband router, you need
to download the firmware file to your local hard disk, and enter that file name
and path in the appropriate field on this page. You can also use the Browse
button to find the firmware file on your PC.
Once you’ve selected the new firmware file, click <Apply> at the bottom of the
screen to start the upgrade process
50
Backup Settings
The Backup screen allows you to save (Backup) the router’s current
configuration settings. When you save the configuration setting (Backup) you
can re-load the saved configuration into the router through the Restore
selection. If extreme problems occur you can use the Restore to Factory
Defaults selection, this will set all configurations to its original default settings
(e.g. when you first purchased the router).
Use the "Backup" tool to save the Broadband router current configuration to a
file named "Routercfg.cfg" on your PC. You can then use the "Restore" tool to
restore the saved configuration to the Broadband router. Alternatively, you can
use the "Restore to Factory Defaults" tool to force the Broadband router to
perform a power reset and restore the original factory settings.
51
Reset
You can reset the router’s system should any problem exist. The reset function
essentially re-boots your router’s system.
52
DDNS
DDNS allows you to map the static domain name to a dynamic IP address. You
must get an account, password and your static domain name from the DDNS
service providers. This router supports DynDNS, TZO and other common DDNS
service providers.
Enable/Disable Enable/Disable the DDNS function of this router
Provider Select a DDNS service provider
Domain name Fill in your static domain name that uses DDNS
Account/E-mail The account that your DDNS service provider assigned to you
Password/Key The password you set for the DDNS service account above
Click <Apply> at the bottom of the screen to save the above configurations.
53
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement