Tender for Electronics and Telecommunication Department for the

Tender for Electronics and Telecommunication Department for the
1
Serial No. :- ………………………..
Issued To :- ………………………..
Date
:-……………………………
Tender Document
For
Electronics And Telecommunication
Department
Last Date of Selling the Tender
14.12.2015 up to 04:00 PM
Last Date and Time of Submission
15.12.2015 up to 12:00 Noon
of Tender Document
Date and Time of Opening of Tender
of Tender Document
Office of the Principal
Govt. Polytechnic Takhatpur
Village-Lidri, P.O- Jarondha
Takhatpur, Distt- Bilaspur (Chhattisgarh),Pin 495330
Email- [email protected]
Website:- www.cgdteraipur.ac.in
Govt.Polytechnic Takhatpur
15.12.2015 up to 03:00 PM
2
Schedule of items and Terms and Conditions
1. The institute wishes to procure the equipments for Labs of Electronics and
Telecommunication department upto 4000000/- ( Fourty Lakh Only) . Mentioned in
Annexure 1.
2. The details of equipment and EMD required are given below.
ANNEXURE –I
S.
No.
1
Lab
Computer Networking
Lab
2
4
Adv. Microprocessor
and Micro-controller
Lab
5
Antenna and
Microwave
Communication Lab
Audio Engg. and
Acoustics Lab
6
Govt.Polytechnic Takhatpur
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
15.12.2015 Up to 12:00 Noon
Advance
communication lab
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
LAN Trainer Kit
Router ,Hub
Wireless Modem
Lan Cables
Fiber Optics Cable Kit
Color TV Trainer Kit
Black & White TV Trainer Kit
Video Camera Kit
LCD/DLP Projector
CCTV Camera Set
a. & Microphone
Optical Fibre Trainer Kit
Satellite Receiver
RADAR Trainer Kit
Photo Detector Kit
MTI Radar
8086 Trainer Kit
8051 Trainer Kit
PC Enter Facing Trainer Kit
Waveforms generator
Gunn Oscillator Trainer Kit
Gunn Diode Trainer Kit
Klystron Tube Amplifier ,Reflex
Klystron Tube Amplifier
Micro wave Element Isolatator
Direction Coupler
VSWR Meter
Pin Diode and Pin Modulator
Home Antena wave Guide
UHF and VHF Transmitter
Antena Parameter Measurement
Kit
Sound Level Meter
Audio Amplifier
PA (Public Address) system
trainer
Stereo System ,Mic Mixture
Last date of last date of
issue of
Submission
Tender
of Tender
14.12.2015 Up to 4:00 PM
3
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Earnest
Money
Deposit
Rs 120000/- ( One Lakh Twenty Thousand only )
TV – Video Technique
& Multimedia Lab
Item
3
7
Microprocessor &
Application Lab
8
Analog Electronics
Lab
10
Principles of
Communication Lab
Power Electronics Lab
12
Electronics Devices &
Circuits Lab
43.
44.
45.
46.
47.
48.
49.
50.
51.
52.
53.
54.
55.
56.
57.
58.
59.
60.
61.
62.
63.
64.
65.
66.
67.
13
Digital Electronics Lab
14
Electrical and
Electronics
Measurement and
Instrumentation Lab
Govt.Polytechnic Takhatpur
68.
69.
70.
71.
72.
73.
74.
75.
76.
AM Trainer Kit
FM Trainer Kit
CRO
PAM/PPM/PWM/ PCM
Trainer Kit
ASK/FSK/PSK Trainer Kit
PCM Kit, Delta Modulation Kit
DSB ,SSB AM Tx /Rx Kit
GTO Trainer Kit
DIC KIT
PUT Kit
SCR Commuting Circuit Kit
Snubber Circuit Kit
Cyclo converter
Chopper Circuit Kit
Parallel Inverter kit
PUT Trainer Kit
Oscillator Trainer Kit
CRO
Hw/Fw Rectifier Trainer Kit
Bridge Rectifier Trainer Kit
UJT Trainer Kit
Voltage Series ,current Series
Amplifier
RC Phase Shift Oscillator
Digital Logic GATE Trainer Kit
Flip Flop Trainer Kit
(JK,D,T F/F)
Digital IC Trainer Kit
Demorgan Theorem Trainer Kit
Counter Trainer Kit
Logic Gates Trainer
CRO
Digital Frequency Meter
Digital Panel meter
Digital Multimeter
Digital Storage oscilloscope
Rs 120000/- ( One Lakh Twenty Thousand only )
9
Sound Mixture
8085 Trainer Kit
Interfacing Kit
OP-AMP Trainer Kit
Differential OP-AMP Kit
Inverting OPAMP Kit
Non Inverting Kit OPAMP
OPAMP as ( Adder, Subtracted
<multi, Divider,Inverter
,Integrater, Buffer , Active Filter
Stable
40. Timer 555 As (Astable,Non
Stable Multivibrater )
41. Analog Multi meter
42. Freq. Generator
33.
34.
35.
36.
37.
38.
39.
4
15
16
19
20
21
Network analysis Lab
Basic Electrical and
Electronics Lab
Fundamentals of
Electrical Engg. Lab
Electronic material
and workshop
Instrumentation and
Process Control Lab
77. Oscillator
78. KCL & KVL Trainer Kit
79. Super Position Theorem Trainer
Kit
80. Maximum Power Transfer
Theorem Trainer Kit
81. Active Filter Trainer Kit
82. Ohms law
83. Rheostat
84. series test, parallel test,
85. Transformer Functioning Kit
86. Transformer Functioning Trainer
Kit
87. Various Power Supply
88. Wattmeter Trainer Kit
89. Digital Multi meter
a. Display: 3½ digits LCD
90. Various Resistor/
Capacitor/Inductor Display
Trainer Kit
91. Solder/De-solder Machine &
Material
92. LCR Meter
93. Various Opening Tool kit
94. LVDT Kit
95. Strain Guage Kit
96. Thermo Couple Kit
97. Resistance Couple Detector
98. Piezoelectic Transducer
99. LDR Kit
3. The Tender in a sealed envelope superscripting Tender for Electronics and Telecommunication Engg.
Document completed in all respect should reach to office of the Principal Govt. Polytechnic Takhatpur
Distt- Bilaspur (C.G) on or before
4. The Tenderer is required to deposit the Earnest money deposit (EMD) of Rs 120000/- ( One Lakh
Twenty Thousand only ) (Refundable ),if he wishes to submit tender for items of equipments for Labs
of ET&T Department. The EMD must be in form of demand draft payable to Principal Govt. Polytechnic
Takhatpur (C.G) as Mentioned above along with tender document failing which there offer shall not be
considered by the institute.
5. The Tender Document Can be Obtained through written request with attaching a Bank Draft of Rs
1000/- ( Five Hundred Rs Only) ( Non Refundable) Payable to Principal Govt. Polytechnic Takhatpur
(C.G) from undersigned office.
Tender document can be downloaded from website
www.cgdteraipur.ac.in and apply with required fees of Rs 1000/-.
Govt.Polytechnic Takhatpur
5
6. The unit rates should be quoted in words and figure for each item .The Tenderer should clearly
mention for any taxes etc. if required .The item are required to be supplied at destination Principal
Govt. Polytechnic Takhatpur Distt.- Bilaspur (C.G).The Tenderer should mention warranty period of
equipment /machine clearly.
7. The supplier has to execute equipment, installation, commissioning, Demonstration and training at
destination Govt. Polytechnic Takhatpur and the cost of it will be bear by supplier.
8. Payment of supplied equipment will be done only after installation and commissioning of equipment
.No any advance payment will be done.
9. Equipment /machine cost, should be inclusive of packing forwarding charges.
10. The Tenderer should indicate the financial turn over during last one year. Legible photocopy or order
of different origination booked during the last one year should be attached .
11. Tenderer of his representative can present on the time of opening of tender document.
12. Principal Govt. Polytechnic Takhatpur reserve the right to cancel the tender document.
13. In case of any dispute the Principal Govt. Polytechnic Takhatpur shall decide the issue and his decision
will be final and shall be binding on the tenderer.
14. Each tenderer should be clearly specify that the tenderer agree to abide by the conditions of this
tender document on their printed letter pad indicating here on sales tax, registration, Fax, Email,
Telephone Numbers etc.
15. The details of Equipment /machine are given at Annexure –I & Annexure –II For ET&T Department.
PRINCIPAL
GOVT. POLYTECHNIC TAKHATPUR
DIST. BILASPUR (C.G.)
Govt.Polytechnic Takhatpur
6
Annexure II
Title: Computer Networking Lab
S.
No
.
Name of the
Equipment to be
procured
Specification (Enclosure Reference)








01. Three sets of onboard cabling setup for ethernet.
02. On board parallel port direct cable connection setup.
03. On board serial port direct cable connection setup.
04. A 10 mbps hub is provided onboard with the circuitry exposed.
05. The power supply circuit for Hub is provided onboard.
06.A separate Hub is also provides so to train students for multi Hub
Networking.
07.A set of 4 exhaustive manuals covering LAN hardware & cabling, software
configurations protocols, terms & definitions.
08.The trainer comes with a cable fabrication kit to provide hands on
experience on real cabling.
SPECIFICATION
LAN HARDWARE
1
LAN Trainer Kit








01. 10/100 Mbps Ethernet Card : 3 Nos.
02. UPT Straight cable with Connectors : 5 mtr.x 3 + ½ mtr.x3
03. Coaxial Cable with connectors and termination : 10 mtr.
04. traight Parallel port cables : 2 Nos.
05. Straight Serial port cables : 2 Nos.
06. 10 Mbps 8 port Hub. : 2 Nos.
07. Set of patch cords for the Onboard cabling setup
08. Cable fabrication kit. : 8 RJ 45 male connectors, crimping tool & 10 mtr.
UTP cables
TRAINING PACKAGES AND EXPERIMENTS
(A) LAN HARDWARE AND CABLING





2
Router ,Hub
01. Setup a network between 2-8 Computers using Hub and straight cables
(WIN XP)
02. Setup a network between two Computers without using Hub by using Cross
cables (WIN XP)
03. Multi Hub Networking (WIN XP)
04. Setup a networking between Two computers using parallel port direct cable
connection.
05. Setup a networking between two computers using serial port direct cable
Connection.


Govt.Polytechnic Takhatpur
Ports
1 SIC slot
1 RJ-45 autosensing 10/100 WAN port (IEEE 802.3 Type 10BASE-T, IEEE
7

802.3u Type 100BASE-TX);Duplex: half or full
4 RJ-45 autosensing 10/100 LAN ports (IEEE 802.3 Type 10BASE-T, IEEE
802.3u Type 100BASE-TX);Duplex: half or full
Throughput
up to 160 Kpps (64-byte packets)
Routing table size
10000 entries (IPv4), 10000 entries (IPv6)
Power and operating requirements
Input voltage
100-120/200-240 VAC
Operating temperature range
0 to 40°C
3
Wireless Modem
4
Lan Cables
5
Fiber Optics Cable
Kit
. Supports HSDPA and UMTS on 850/1900/2100 MHZ,Quad-band class 12
EDGE/GPRS on 850/900/1800/1900MHZ . Download up to 7.2 Mbps on HSDPA
and UMTS capable networks,and upload up to 2 Mbps . EDGE data up to 236.8Kpbs
. 8G MicroSD memory expansion . Plug and Play through ..
PVC shielded twisted pair UTP/FSTP LAN (Computer) cable Conductor Type
Copper Insulation PVC
Range:* CAT 5
* CAT6
* CAT 5E (FSTP)
Technical SPECIFICATION:“Fiber Optic Trainer Kit” (Model:
iDC_109_Link_TDM)
Transmitter: 1 Nos Fiber optics LED
i) Peak wavelength of emission 660 nm Red visible (IF-E97 or SFH-756).
Receiver:2 Nos. Fiber Optic Photo Detector i) Photo detector IF-D91 [SFH-250V] is
capable of 100Mbps data rates. They also can be used in analog video links with
bandwidths up to 70 MHz
Modulation Techniques : (i) Direct Intensity Modulation
(ii)Time
Title: TV – Video Technique & Multimedia Lab
S.
No.
6
Name of the
Equipment to be
procured
1. Color TV Trainer
Kit
Govt.Polytechnic Takhatpur
Specification (Enclosure Reference)
a.
b.
c.
d.
e.
f.
g.
h.
i.
j.
System: CCIR-B-PAL-G, 625 lines.
Power Supply : 230V+15%AC, 50Hz
Regulation range :195V AC to 265 AC.
Power consumption :70 watts.
Gain Limited sensitivity : 60 Db for Video 30 Db for Audio
Sound output : 5.0 watts maximum
Picture Tube Size: 53cms (Diagonal) full Flat square tube FFST
Tuner Channels: VHF2 to 12 UHF 21 to 68, S-band & hyper-band
Tuner Channel Positions: 106 Channel positions.
Program memory : 90 Programs.
8
k. On screen display for setting of all controls e.g. Volume, Brightness, Contrast,
Colour, Channel and band selection tuning
l. Remote Controller should be in trainer form.
m. Audio-Video In and out sockets.
n. Section : Operating unit & Tuner, Remote Receiver, Video I.F. , sound.
o. controls : Volume, Brightness, Contrast, Colour. Channel & band selection,
Tuning.
p. Remote Control functions : Volume, Brightness, Contrast, colour, Channel
selection, Audio mute.
q. Distortion : 10 to 15% in Live program due to expanded P.C.B.
1. trainer P.C.B.
2. picture tube fitted in moulded cabinet.
The complete circuit of remote colour TV should be printed on single Board.
All parts should be soldered on single pin tag for easy replacement and fault creation.
Fault creation facilities should be provided by Switches and by changing parts.A
detail manual of colour TV should be provided.
A Manual having Detailed practical.
Technical Specifications:
CCIR Standards:
Lines :
625
Picture IF :
38.90 MHz
Sound IF :
33.40 MHz
Video Band Width
6 MHz
:
Inter carrier sound
5.5 MHz
IF :
7
Black & White TV
Trainer Kit
Channels :
100
Band III :
5 to 12
4:3
Aspect Ratio :
Types of Modulation
Amplitude Modulated
Picture :
Frequency Modulated
Sound :
Name of Section : Tuner, Horizantal, vertical, vision, sound & EHT
Power Supply :
SMPS
EHT unit :
BD 115 and BU 205
Video output :
BD 114.transistor
Vertical output : IC 2130
Horizontal
oscillator :
IC CA 920
Vision IF :
IC CA 3068
Tuner :
Electronic Tuning
Sound IF
Audio :
and
IC 1190
Test points and controls should be available at the respective points in the stage-wise
and circuit Diagrams of each section are printed on the PCB.
Govt.Polytechnic Takhatpur
9
Housing:
8
Video Camera Kit
9
LCD/DLP Projector
10
CCTV Camera Set
& Microphone
It should be housed is an elegant metal cabinet
230VAC - Mains operated
Power:
Wireless camera kit 2. 4 Ghz Wireless Camera Kit, USB DVR 4ch 1 mini pinhole
camera for surveillance.
Specifications :
* Imaging sensor : 1/3" CMOS
* CMOS total pixels : Pal 628 x 582, NTSC 510 x 492
* Horizontal resolution : 380 TV lines
* View angle : 62
* Minimum illumination : 1. 5 Lux / F1. 5
* Gain control : automatic
* Frequency : ISM 2, 400MHz ~ 2, 483MHz 4CH
* Transmission power : 10mW
* Modulation mode : fM
* Bandwidth : 18MHz
Brightness4300 ANSI Lumens (Max.)Throw ratio1.28 (wide) -1.536 (tele) Projection
screen size At 1.2m (3.94 ft) distance, diagonal projection image size of 0.92m
(36.3).Projection distance At 10m (32.81 ft) distance, diagonal projection image size
of 9.2m (362).Lamp1.2m ~ 10m (3.94 ft ~ 32.81 ft)Number of pixels Philips 300W
user-replaceable lamp Up to 2, 000 hours Typical and Up to 2, 500 hours Eco-Mode
Contrast ratio WXGA (1280 x 800)Displayable colors2000:1
1. System : Colour PAL B/G
2. Power supply : 12 V DC
3. Resolution : 420 TV Lines- Horizontal
4. CCD Image Sensor : 1/3" Image format
5. Gray Scale : Minimum 10 steps
6. Video Output : 1.0 Vpp, 75 Ohms, RCA Socket.
7. External Arrangement : Hor. 350°, Ver. 90°
8. Gamma Correction : 0.45
1. Type : Condenser
2. Frequency Range : 20 Hz to 10 KHz
3. System : Omni directional
4. Sensitivity : 68 dB + 3 dB
1. Type : 7“ SVGA LCD Monitor
3. Inputs : Audio/Video Inputs - RCA sockets Standard (mm)7.4 x 7.4
Active Area (mm) 11.8 x 8.9 mm
Active Area (mm2 Accessories: A Manual having practicalS.CCD specs:
Array Size (pixels) 1600 x 1200
Pixel Size (microns) 105
Title: Advance Communication Lab
S.
No
.
Name of the Equipment
to be procured
Govt.Polytechnic Takhatpur
Specification (Enclosure Reference)
10
11
12
Optical Fibre Trainer Kit
Satellite Receiver (disk
TV OR Setup Box )
All analog and digital modulations and pc to pc,over 660nm, 950nm OFC,





















Low Threshold Digital Tuner, with Loop Through
MCPC/SCPC all Support (2 -45 Mb /s)
Picture in Graphic (PIG)
EPG For On Screen Channel Information
DiSEqC 1.2., 1.0 version Compatible
RS-232 Serial Port with Max. 115K Baud Rate
System Upgrading & Data Transfer via PC to Unit ro Unit to Unit
Programmable of 2000 Digital channels
Over 50 satellite/ 1000 TP Programmable
Auto Channel Search & Save Function
Network Search Available
Manual PID Insertion and Scan Function
3 Favorite Channel Lists
Channel List Edit Function
Tele - Text & sub - Title Support
Quick Channel Zapping <1 Second
1Last Channel Memory
Event Timer Parental Lock for Channel & Menu
4:3, 16:9 Screen Auto Selection
12 Language OSD Menus (English, German, French, ltalian, Spanish ,
Arabic, Turkish, Portuguese, Russian,)
SMPS Power Supply (85-260V, 50/60Hz, 25W Max).
Microwave Transceiver
Type
: MMIC tranciever with parabolic dish antenna.
Antenna Size : 30cm dia with f/d 0.3
Frequency : 10.5 GHz DRO stabilized
Output Level : 0 dBm typical
Sensitivity : -70dBm typical
Output
: PC Compatible
Software
13
RADAR Trainer Kit
Speed Display : Display in km/hr, miles/hr, m/s, rpm, event, KHz
Frequency set : gate time selectable from 10 ms to 1000ms and frequency
threshold selectable from 1mV to 1000mV
Oscilloscope
Oscilloscope : Real time with digital storage
Display setting : Both X and Y position adjustable
Volts/div : Adjustable
Time Base
: Adjustable
Trigger : Auto
Fast Fourier transform
FFT
: Real time Simultaneous speed and frequency display with cursor
measurement
Scanwidth : Selectable in steps
Govt.Polytechnic Takhatpur
11
Settings
Activity Log : User defined Start and Stop Event
Display : Peak to peak voltage display
Annunciation : audio & visual
Alarm
: Adjustable threshold with
Event counting : With reset to zero
Speed Factor : User settable Hz/(Km/hr)
Counter
: In built frequency counter in GUI
Audio in/out : Volume settings; alarm On/Off Settings
Accessories : Tuning Fork, Buzzer, Turbine Fan, Pendulum, Reflector Panel
Moving Target Emulator
Range
: 0 to 1000km/hr
Random Noise Jammer
Stealth accessory : RAM Cones, Sheets, Paints
Scale models
: F117 stealth fighter, B2 Bomber
Reference targets : Corner reflector, Flat plate, Sphere - Metallic
.
14
Photo Detector Kit
Range: 400 mm...
- system
- One (1) horn antenna for a gain of 21,4 dBi. (replacing the horn antennae
of the base module)
- One (1) hand controller
15
MTI Radar
- One (1) reflector
- Four (4) feet
- One (1) Laptop for control and analysis including operating system and
the processing, analysis, visualization and recording software
& accesories
Title: Advance Microprocessors & Microcontrollers Lab
S.
No
.
16
Name of the Equipment
to be procured
8086 Trainer Kit
8086 MP. Kit with
Inbuilt Assembler
microprocessor kit with
LCD display
Govt.Polytechnic Takhatpur
Specification (Enclosure Reference)
8086/8088 CPU operating at 2.5/5MHz
8086 Processor can be replaced by 8088 Processor
On-board sockets should be provided to facilitate the use of 8087 Coprocessorand 8089 I/O
Processor
16K bytes of RAM using two nos. of 6264 with Battery Backup expandable up to 256KB
16K bytes of powerful monitor EPROM using two nos. of 27512
72 I/O lines through 3 nos. of 8255 brought at 26 Pins FRC Connector to interface with
IC-XX Series
16 bit Timer/Counter through 8253 brought out at 20 Pins FRC Connector
RS-232C interface using 8251 brought out at 9 Pins DType Connector. On-board Interrupt
controller using 8259 brought out at 20 Pins FRC Connector
12
17
18
8051 Trainer Kit
PC Enter Facing
Trainer Kit
28 keys hexadecimal keyboard and eight seven segment display using 8279
Two modes of operation:
-Keyboard Mode
-Serial Mode
Powerful Commands like Examine/Edit Memory, Examine/Edit Register, Single stepping,
Execution, Block Move can be used through hex keyboard or PC serial mode
Facility for Downloading/Uploading files from/to PC
All address, data & control lines are available on KXT Bus 50 pin FRC Connector to
interface with SC-XX Series
All ICS are mounted on IC Sockets.
Bare board Tested Glass Epoxy SMOBC PCB is used
In-Built Power Supply of +5V/2A, ±12V/250mA
Attractive Wooden enclosures of Light weight Australian Pine Wood
User's Manual with sample programs
8051 / 89C52 CPU operating @ 11.0592 MHz.
_ 32K user RAM with Battery Backup using NICD Battery.
_ 16K bytes of monitor EPROM.
_ One memory socket should be provided for expansion upto 64K.
_ 48 I/O lines using 2 Nos. of 8255 brought at 26 Pins FRC Connector.
_ Three channel timer / counter using 8253.
_ 20 x 2 Backlite LCD Display with 101 ASCII Keyboard.
_ Two External interrupts INT0 & INT1.
_ RS - 232C using RX / TX of 8051.
_ Single Line Assembler / Disassembler.
_ Two modes of operation:
_ ASCII Keyboard Mode.
_ Serial Mode.
_ Powerful Commands like Examine / Edit Memory, Examine / Edit Resistor, Single
stepping, Execution,
Break Point can be used through ASCII keyboard or PC serial mode.
_ Facility for Downloading / Uploading files from / to PC.
_ All Address, Data, Control and Port lines are available on 40 Pins and 10 Pins FRC
Connector.
_ In - built power supply of + 5V / 1A, + 12V / 150mA.
_ User’s Manual with sample programs.
 It should be used to study basics of Analog To Digital conversion using Processors /
Controllers and develop real time process control applications.
 ADC-01 card incorporates monolithic CMOS 8 bit successive approximation analog to
digital converter ADC-0809.
 This converter features a high impedance chopper stabilized comparator, its resolution
is 8 bits and conversion time is 100 secs.
 It should be programmable clock oscillator that generates 100 KHz clock signal.
 The PCB track design is shielded to keep low noise level in the analog paths and this
card gives stable analog input readings.
 The card is also protected for reverse supply polarity.
Title: Antenna & Microwave Communication Lab
S.
No
.
19
Name of the Equipment
to be procured
Waveforms :
generator
Govt.Polytechnic Takhatpur
Specification (Enclosure Reference)
Sine RF Generator : 750 MHz approximately
(output adjustable)
Tone Generator : 1 KHz approximately
13
20
Gunn Oscillator Trainer
Kit
21
Gunn Diode Trainer Kit
22
Klystron Tube Amplifier
,Reflex Klystron Tube
Amplifier
23
Micro wave Element
Isolatator Direction
Coupler
24
25
26
27
VSWR Meter
Pin Diode and Pin
Modulator
Home Antena wave
Guide
UHF and VHF
Transmitter
Govt.Polytechnic Takhatpur
(output adjustable)
Directional Coupler : Forward & Reverse (selectable)
Matching Stub : Slider type
Antenna Rotation : 0-360 deg. Resolution 1 deg.
Receiving Antenna : Folded dipole with reflector
Detector Display : Level adjustable meter
Interconnections : 2 mm Banana sockets
Power Supply : 230 V, ±10% 50/60 Hz
Power Consumption : 3 VA approximately
Included Accessories :
Detector Antenna : 1 no.
Learning material : CD (Theory, procedure,
reference results, etc)
model freq. Range(ghz) pushing factor (mhz/v) bias voltage max. nominal power out put(mw) temp coeff. (mhz/°c) output connector frequency adjustment wave guide flange 1
8. 2-12. 4 8 10v 10 ±0. 2 bnc(f) by micrometer rg-52u ug-39/u 2 12. 8-16. 5 12 8v 10 ±0. 4
bnc(f) by micrometer rg-91u ug-419/u
Gunn Power Supply (Digital).
b. VSWR Meter Solid State.
c. Gunn oscillator.
d. Pin Modulator.
e. Isolator.
f. Frequency meter ( Direct reading ).
g. Variable attenuator.
h. S.S. Tuner.
i. Tunable probe.
j. Slotted section.
k. Diode Detector.
l. BNC to BNC Cable.
Operationg Voltage - 230V+/- 10%, 50Hz AC
Beam supply - Voltage:200-300V continuously variable; Current: 50mA max.; Regulation:
better than 0.5% for +/-10% variation in mains supply...
Sma directional coupler 10db coupled port from 0.5MHzto100MHz
Sensitivity : 0.1mV for 200W input impedance for full scale deflection. Noise Level : Less
than 0.02mV Range : 0 – 60dB in 10dB steps. Input : Un-biased low and high impedance
crystal biased crystal (200W and 200K) Meter Scale : SWR 1-4, SWR 3-10, dB 0-10,
expand SWR 1-1.3, dB 0-2. Gain Control : Adjusts the reference level, variable range 0 10dB (approx.) Input Connector : BNC (F)
should allows current to flow only in one direction and blocks the current that flows in the
opposite direction. And suitable pin modulator
Frequency range : 86 - 860 Mhz PLL for Rx
Step size : 0.05, 0.1, 0.25, 0.5, 1, ...
The WML 12V- 500 VHF and WML 12U- 500 UHF Class-AB Low Power T.V.
Transmitter should be designed to meet the high performance standards required for color
T.V. Broadcasting applications over Band III & Band IV & V Channel frequencies. The
transmitter adopts the advanced trends in design such as, use of solid state Class-AB RF
Power Amplifiers, modulation at IF and use of SAW (Surface Acoustic Wave) filter to
determine VSB Characteristics, highly stable synthesizer and change over facility from
main to standby exciter or vis a versa.
The transmitter is housed in a stand alone standard 19" rack. Rack should be made up of
specially designed aluminium extrusion
The transmitter should have output port (1 5/8" E.I.A. Flange Connector) on top panel of
rack. Input Video and Audio port are given on the back panel of the 'exciter change over
unit. A 600 Watt 50 Ohms Load is provided inside the rack for terminating transmitter
14
power.
The transmitter should be designed to have full redundancy. Driver stages are in-built in
individual Power Amplifier.
28
This system consists of a wide band PLL based source and detector module working up to
3GHz, a very strdey non magnetic Transmitter and Receiver stand, Universal Antenna
Mount with plug and fit assembly and radiation pattern plotting software
Antena Parameter
Measurement Kit
Title: Audio Engineering & Acoustics Lab.
S.
No.
29
30
Name of the Equipment
to be procured
Sound Level Meter



























Audio Amplifier
Amplifier with 250 watt,
USB drive
Govt.Polytechnic Takhatpur
Specification (Enclosure Reference)
Standard Applied Iec651 Type 2, Ansi S1.4 Type 2
Frequency Range 31.5Hz - 8Khz
Measuring Level Range 30 - 130Db
Frequency Weighting A/C
Microphone ½ Inch Electrical Condenser Microphone
Calibration
Electrical Calibration With The Internal Oscillator
(1Khz Sine Wave)
Display
Lcd
Digital Display
4 Digits
Resolution
0.1 Db
Display Up Data
0.5 Sec.
Times Weighting
Fast (125Ms), Slow (1 Sec.)
Level Ranges
Lo: 30-100Db
Hi: 65-130Db
Accuracy
± 1.5Db (Under Reference Conditions)
Alarm Function
Over Is Shown When Input Is Out Of Range
Maximum Hold
Hold Readings The Maximum Value, With
Decay < 1Db/3Minutes.
Power Supply
One 9V Battery, 006P Or Iec 6F22 Or Neda 1604.
Power Life About 50Hrs (Alkaline Battery)
Operation Temperature 0°C To 40°C (32°F To 140°F)
Operation Humidity 10 To 90% Rh
Storage Temperature -10°C To 60°C (14°F To 140°F)
Storage Humidity 10 To 75% Rh
Dimensions 210 (L) X 55(W) X 32 (H)Mm
Weight 230G (Including Battery)
Accessories 9V Battery, Cary Case, Instruction Manual.
Power Output
500W Max.: 350W RMS at 10% THD
320W RMS at 5% THD, 300W RMS at 2%
THD
Output Regulation
<2 dB, no load to full load at 1kHz
Input Channels
7 x Mic 0.8mV/4.7 kΩ, 2 x Aux
100mV/470
kΩ
1 x Line 1V/50kΩ
Frequency Response
50-15000 Hz + 3dB
Signal to Noise Ratio
60dB
15
Tone Controls
Bass: + 10dB at 100Hz, Treble: + 10dB at
10kHz
Outputs
Preamp 200mV/600Ω, 1V/1kΩ
Speaker Outputs
4Ω, 8Ω, 70V & 100V
Power Supply
AC: 220-240V 50/60 Hz DC: 36V (3 x
12V Car Battery)
Power Consumption
AC: 660VA DC BA
Dimensions
W450 x H160 x D 340 mm
Weight
15 kg
60 dB.
31
mic. & One Aux. inputs.
220VAC 50 Hz.
80 Watt RMS Max.
Bass, Treble.
PA (Public Address)
system trainer
4,8 &16 Ohms.
ided at appropriate places on panel for
connections / observation of waveforms.
Design procedures, Report Suggestions and Book Reference
32
Stereo System ,Mic
Mixture ,Sound Mixture
Cordless Mic )









6-inch woofer, 1-inch high frequency driver
40 watts of power from a lightweight Class D amplifier
Built-In VHF wireless microphone system
iPod dock with level control
Speaker stand pole-mount receptacle, Rechargeable battery included
6-Inch woofer with 1-inch high frequency driver
Channel 1: XLR-1/4 inch combo line or mic level input with phantom power
Channel 2: 1/4 inch line or microphone level input
1/8 Inch stereo aux input allows for stereo line level signal
Title: Microprocessor & Application Lab
S.
No
.
33
Name of the Equipment
to be procured
8085 Trainer Kit
microprocessor kit with
LCD display
Govt.Polytechnic Takhatpur
Specification (Enclosure Reference)
* CPU : 8085 Microprocessor @6.144 MHz
* MEMORY : Total space ON BOARD is 48KB,Comprising of 16KB monitor EPROMS
and 32KB RAM. Battery backup
for RAM. No expansion required.
* PERIPHERALS : 8279 for controlling 24 feather keys (including 6 digit seven segment
display).
: 1 Timer/counter with three independtly programmable counters.
: Two 8255 for controlling 48 I/O lines and same are brought out to FRC 50 pin connector.
: 8251 for RS 232 C serial communication and firmware for UP/DOWN facility for IBM
PC/XT/AT computer.
: Built-in cassette interface.
: Built-in Speaker interface.
16
34
Interfacing Kit
(IC8255,IC8155,IC8279)
: Built-in EPROM programmer for 27128 operating at 12.5V.
* INTERFACING : All buffered & demultiplexed TTL compatible signals brought on a
50 pin FRC connector including address and
SIGNALS data control lines brought out at another 50 pin FRC connector. Several
experimental interface modules can be
connected to this trainer. They are ADC, DAC, Stepper motor, 8-bit switch input, 8-bit
LED output, Relay
interface module, etc. and many more are available.
Universal IC tester
It can test more than 600 IC’s comprising of 74 Series, 40/45 Series
* It can test Micro-processor 8085, 8086, Z80, 8051, 89c51 and Peripherals like 8255,
8279, 8253, 8259, 8251, 8155, 6264, 62256, 8288, 8284 etc.
* It tests Op-amp, 555, Transistor Arrays, Analog switches, Opto couplers etc.
* It tests Seven Segment Display of common cathode and common anode type
* It has Auto search facility of all Digital IC’s
* Test by: Truth table / sequence table...
Title: Analog Electronics Lab
S.
No.
35
Name of the Equipment
to be procured
OP-AMP Trainer Kit
36
Differential OP-AMP
Kit
37
Inverting OPAMP Kit
38
Non Inverting Kit
OPAMP
Govt.Polytechnic Takhatpur
Specification (Enclosure Reference)
Built in power supply +9Vat 200mA IC Regulated & short circuit protected. Power
requirement 230V Ac 250 V, 50Hz Ac. Op amp 741 Inverting & Nov inverting
Configuration. All parts are soldered on signal PCB with complete circuit diagram
Screen printed section wise in multi colour with multicolored test points.
Accessories:- I. Manual, 2mm Patch cord
Following experiments can be performed :
01. Basic operational amplifier circuit
01. Inverting amplifier
02. Non-inverting amplifier
03. Inverting A.C. amplifier
04. Non-inverting A.C. amplifier
05. High input impedance inverting amplifier
06. High input impedance non-inverting amplifier
02. SOURCE FOLLOWERS
01. Voltage Follower (Unit...
Following experiments can be performed :
01. Basic operational amplifier circuit
01. Inverting amplifier
02. Non-inverting amplifier
03. Inverting A.C. amplifier
04. Non-inverting A.C. amplifier
05. High input impedance inverting amplifier
06. High input impedance non-inverting amplifier
02. SOURCE FOLLOWERS
01. Voltage Follower (Unit...
Following experiments can be performed :
01. Basic operational amplifier circuit
01. Inverting amplifier
02. Non-inverting amplifier
03. Inverting A.C. amplifier
04. Non-inverting A.C. amplifier
17
39
40
OPAMP as ( Adder,
Subtracted <multi,
Divider,Inverter
,Integrater, Buffer ,
Active Filter Stable
multivibrater, Signal
Generator , Oscillator )
Timer 555 As
(Astable,Non Stable
Multivibrater )
41
Analog Multi meter
42
Freq. Generator
Govt.Polytechnic Takhatpur
05. High input impedance inverting amplifier
06. High input impedance non-inverting amplifier
02. SOURCE FOLLOWERS
01. Voltage Follower (Unit...
 +12 GND -12 power supply for IC
 Two 0-5 v (V 1 & V 2) variable power supply for doing experiment
 Resistors of suitable values for series & feedback resistors
 Digital meter with selector switch to read input (V 1 & V 2) and output
 Easily stackable patch chords

Built in power supply : +12V DC

Mains : 230V AC

Dimension : 27CMS X 17CMS [metal cabinet]

Weight : 2KGS APPX
Pocket size multimeter is self-contained portable test set that measures a wide
range of Voltages, Currents and Resistances. This is an indispensable instrument
for servicing and maintenance of electronic equipment, radio and television. The
meter is so designed and its movement is heavily damped to avoid damage to the
meter movement. The internal batteries measure resistance from 2 ohms upto 1 M
ohms.
Range : DC voltage : 0.25/10/50/250/1000V
(4K ohm/V) ± 3% AC voltage : 10/50/250/500/1000V
(2K ohm/V) ± 4% AC current : 0.25/10/250mA ±3% Resistance : 0-10K/1M ohm
(min.2 Ohms &...
* Frequency Range A:100KHz~300KHz
B:300KHz~1MHz
C:1MHz~3.2MHz
D:3MHz~10MHz
E:10MHz~35MHz
F:32MHz~150MHz
* 3rd harmonic : up to 450MHz
* Frequency Accuracy : ±Resolution ±1digit
* RF output Amplitude : 100mVrms(at 35 MHz)
* Amplitude Control : 0Db/20dB and fine tune
* Modulation : INT.1KHz
* EXT.50Hz~20KHz (at <1Vrms)
* Audio Output : 1KHz(fixed),Min.1Vrms
* Frequency Meter
* Frequency Range
* Low frequency : 10Hz~10MHz
* High frequency : 10MHz~150MHz
* Input Sensitivity : Less than 50mV
* Max. Input Voltage : Approx. less than 3Vrms
* Accuracy Low frequency : 1Hz/High frequency 10Hz
* Input Impedance : Low frequency 1MW/High frequency 50MW
* Operating Temperature : 00~400 C
18
Title: Principles of Communication Lab
S.
No.
Name of the Equipment
to be procured
Specification (Enclosure Reference)
Feature:The board consists of the following built-in parts:
1.
2.
3.
4.
5.
6.
43
AM Trainer Kit
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
IC REGULATED POWER SUPPLY : ± 15 DC and +5V DC at 100mA.
AF Modulation signal generator : Sine wave
o Frequency Range : 300 Hz to 3.4 KHz
o Amplitude : 0 to 5 Vpp.
03. RF carrier signal oscillator.
o Frequency Range : 100 KHz to 1 MHz.
o Amplitude : 0 to 10 Vpp.
Local Oscillator : 400 KHz to 500 KHz.
Band Pass Filter : 452 KHz to 458 KHz.
DC Source Variable power supply to
o see the effect of DC on the output waveform : - 5 to + 5 VDC
Output Audio amplifier with Volume Control.
Input Audio amplifier for modulating external signal from Mike or Tape recorder.
Duble Balanced Amplitude modulator
Diode detector.
Product detector
Low pass filter.
Power supply requirement 230V AC, 50 Hz.
Mains ON/OFF switch, fuse and jewel light.
Dynamic Microphone with 4mm Jack Pin.
Loud Speaker with baffle fitted in a box with two metre wire and 2mm Banana pins
for connections.
Good Quality, reliable terminal/sockets are provided at appropriate places on panel
for connections/ observation of waveforms.
Strongly supported by detailed Operating Instructions, giving details of Object,
Theory, Design Procedures, Report Suggestions and Book References.
Weight : 6 Kg. (Approx.)
Dimension : W 412 x H 150 x D 310
Feature:
The
board
01. POWER
consists
SUPPLY : ±
of
12DC
the
IC
following
Regulated
02. FM Modulating signal generator : Sine wave
44
FM Trainer Kit


Frequency Range : 300 Hz to 3.4 Khz
Amplitude Range : 0 to 5 Vpp.
03. Modulator Type :


Varactor modulator (With carrier frequency adjustment)
Reactance Modulator (With carrier frequency adjustment)
04. Demodulator :
Govt.Polytechnic Takhatpur
built-in
parts:
power
supply.
19





:Detuned resonant detector.
: Quadrature detector
: Foster - Seeley Detector
: Ratio Detector
: Phase locked loop Detector
05. Mixer/Amplifier :

1 No. (With gain adjustment) Allows FM input signal to be amplitude modulated by
a noise input to demodulation.
06. Low pass Filter :

3.4 KHz.:Cut of frequency Amplifier (with adjustable gain)
07. VCO Circuit :

FM Wave form demonstrate
08 Test
Point
: 78
09. Power supply requirement :

: 230VAC, 50 Hz.
10. On
11. On
12. Input
13. A self
Board
Board
- Output
Amplitude
and
Switched
limiter
Test
with
points
Faults : 8 Nos.
Amplitude
provided
on
contained
control.
board.
Trainer.
14. Effect of noise on the detection of FM signal may be investigated.




CRO
45
46
PAM/PPM/PWM/
Govt.Polytechnic Takhatpur
Good Quality, reliable terminal/sockets are provided at appropriate places on panel
for connections/ observation of waveforms.
Strongly supported by detailed Operating Instructions, giving details of Object,
Theory, Design procedures, Report Suggestions and Book References.
Weight : 6 Kg. (Approx.)
Dimension : W 412 x H 150 x D 310
1. Power supply requirement
: 230V AC, 50 Hz.
2. WITH FAULT GENERATION AND TEST POINTS ON P.C.B.
3. WITH Built in regulated Power supply 3. WITH CRT
4. WITH SAPERATE HORIZONTAL ,VERTICAL AND POWER SUPPLY
SECTIONS be printed on PCB for easy calculation.
5. Standard Accessories :
1. User Manual with practical and circuit diagrams in two copies.
2. Connecting patch cords - sufficient nos.
FOR PWM The board consists of the following built-in parts:
20
PCM Trainer Kit













± 6V D.C. at 100mA, IC regulated Power Supply internally connected
Pulse Train (Carrier) Generator based on timer IC
50 Hz A.C. sinusoidal modulating signal obtained from stepped down transformer
Pulse Width Modulator based on timer
Pulse Width Demodulator based on operational amplifier
Adequate no. of other electronic components
Mains ON/OFF switch, Fuse and Jewel light
The unit is operative on 230V ±10% at 50Hz A.C. Mains
Adequate no. of patch cords stackable from rear both ends 2mm spring loaded plug
length ½ metre
Good Quality, reliable terminal/sockets are provided at appropriate places on panel
for connections/observation of waveforms
Strongly supported by detailed Operating Instructions, giving details of Object,
Theory, Design procedures, Report Suggestions and Book References
Weight : 3 Kg. (Approx)
Dimension : W 340 x H 110 x D 210
FOR PCM
















5V D.C. at 100mA IC regulated power supply internally connected.
± 15V D.C. at 100mA IC regulated power supply internally connected.
+ 5V D.C. to -9V Variable D.C. output.
Built in TTL Clock Generator 33 KHz.
Modulating Signal Generator 15Hz to 300Hz.
PCM Encoder.
PCM Decoder.
Data display with LED’s
Adequate no. of other electronic components.
Mains ON/OFF switch, fuse and jewel light.
The unit is operative on 230V ±10% at 50Hz A.C. Mains.
Adequate no. of patch cords stackable from rear both ends 4mm spring loaded plug
length ½ metre.
Good Quality, reliable terminal/sockets are provided at appropriate places on panel
for connections /observation of waveforms.
Strongly supported by detailed Operating Instructions, giving details of Object,
Theory, Design procedures, Report Suggestions and Book References.
Weight : 3 Kg. (Approx.)
Dimension : W 340 x H 110 x D 210
The board consists of the following built-in parts :
12V D.C. at 50mA, IC regulated power supply internally connected.
5V D.C. at 50mA, IC regulated power supply internally connected.
47
ASK/FSK/PSK Trainer
Kit
Govt.Polytechnic Takhatpur









Clock Generator 200Hz to 15KHz.
8 Bit Word Generator.
Logic Selection switches for high / low (9Nos).
Binary Counter (Divided by 16 counter).
Carrier Signal Generator 40 to 100KHz.
Amplitude Shift Key (ASK) Modulator.
Amplitude Shift Key (ASK) Demodulator.
Mains ON/OFF switch, fuse and jewel light.
The unit is operative on 230V ±10% at 50Hz A.C. Mains.
21





Adequate no. of patch cords stackable 4mm spring loaded plug length ½
metre.
Good Quality, reliable terminal/sockets are provided at appropriate places on
panel for connections /observation of waveforms.
Strongly supported by detailed Operating Instructions, giving details of
Object, Theory, Design procedures, Report Suggestions and Book
References.
Weight : 3 Kg. (Approx.)
Dimension : W 340 x H 110 x D 210
The board consists of the following built-in parts :
48
PCM Kit, Delta
Modulation Kit )
















±12V D.C. at 100mA IC regulated power supply internally connected.
Quad Op-Amp IC.
Two Up/Down counter IC.
Digital to Analog convertor DAC IC.
Quad two input NAND gate IC.
Timer IC.
Cooperator IC.
5V D.C. at 100mA IC regulated power supply internally connected.
Potentiometer for varying amplitude of modulating signal.
Mains ON/OFF switch, fuse and jewel light.
The unit is operative on 230V ±10% at 50Hz A.C. Mains.
Adequate no. of patch cords stackable from rear both ends 4mm spring
loaded plug length ½ metre.
Good Quality, reliable terminal/sockets are provided at appropriate places on
panel for connections /observation of waveforms.
Strongly supported by detailed Operating Instructions, giving details of
Object, Theory, Design procedures, Report Suggestions and Book
References.
Weight : 3 Kg. (Approx.)
Dimension : W 340 x H 110 x D 210
FOR DSB SSB AM Transmitter Trainer
The board consists of the following built-in parts:
49
DSB ,SSB AM Tx /Rx
Kit
Govt.Polytechnic Takhatpur
1. AF Modulating signal generator : Sine wave
o Frequency Range : 300 Hz to 3.4 KHz
o Amplitude : 0 to 5 Vpp.
2. RF carrier signal oscillator
o Amplitude : 0 to 10 Vpp.
o Frequency Range : 100 KHz to 1 Mhz.
3. Modulators (Two Nos) : Double Balanced Amplitude modulator
4. Ceramic Band Pass Filter : 452 KHz to 458 KHz.
5. Band Pass Filter : 1 No.
6. Switch faults : 8 Nos.
7. POWER SUPPLY : ± 12DC and +5V DC IC Regulated power supply.
8. Test points : 27 Nos.
9. BFO Oscillator : 455 KHz.
10. Input Audio amplifier with Volume Control for modulating external signal
from Mike or Tape recorder.
22
11. Output Amplifier Transmitter : ( Gain adjustable) DSB (1MHz), SSB (1.445
MHz) connected to Antenna/cable.
12. Mains ON/OFF switch, fuse and jewel light.
13. Power supply requirement 230V AC, 50 Hz.
14. Dynamic Microphone with 4mm Jack Pin.
15. Good Quality, reliable terminal/sockets are provided at appropriate places on
panel for connections/ observation of waveforms.
16. Strongly supported by detailed Operating Instructions, giving details of
Object, Theory, Design Procedures, Report Suggestions and Book
References.
17. Weight : 6 Kg. (Approx.)
18. Dimension : W 412 x H 150 x D 310
FOR DSB SSB AM Receiver Trainer
The
board
consists
of
the
following
built-in
parts:
01. POWER SUPPLY : ± 12DC and +5V DC IC Regulated power supply.
02. Detectors/Demodulator : 1. Diode Detector (For DSB)

: 2. Product Detector (For SSB)
03.
Frequency
Range
04.
Intermediate
05. Input Circuits :











: 980KHz
frequency
to
1650
: 455
KHz.
KHz.
1. RF Amplifier
: 2. Mixer
: 3. 1st Amplifier
: 4. 2nd Amplifier
: 5. Local oscillator
: 6. Envelope Detector (AGC)
: 7. Switch Fault
: 8. Product Detector
: 9. IC Regulated Power Supply
: 10. Beat frequency oscillator / 455 KHz Crystal oscillator
: 11. Output Audio Amplifier
06.
Receiving
media
: Telescopic
Antenna
/ cable.
07.
Tuning
: with
variable
capacitor.
08.
Switched
faults
: 8Nos.
09.
Test
points
: 50.
10.
Power
supply
requirement
: 230V
AC,
50
Hz.
11.
Mains
ON/OFF
switch,
fuse
and
LED.
12.
Audio
Output
amplifier
with
Volume
Control.
13. Loud Speaker with baffle fitted in a box with two metre wire and 2mm Banana
pins for connections.



Govt.Polytechnic Takhatpur
Adequate no. of patch cords stackable from rear both ends 2mm spring
loaded plug length ½ metre.
Good Quality, reliable terminal/sockets are provided at appropriate places on
panel for connections/ observation of waveforms.
Strongly supported by detailed Operating Instructions, giving details of
Object, Theory, Design Procedures, Report Suggestions and Book
23


References.
Weight : 6 Kg. (Approx.)
Dimension : W 412 x H 150 x D 310
Title: Power Electronics Lab
S.
No
.
Name of the
Equipment to
be procured
Specification (Enclosure Reference)
Objective:

To conduct the experiment of the GTO characteristics

By applying voltage to the GTO you can able to study the saturation condition

To draw its characteristics
Technical Specification :
50
GTO Trainer
Kit
51
DIC KIT
52
PUT Kit
53
54
SCR
Commuting
Circuit Kit
Snubber
Circuit Kit

Built in power supply : +15V DC

Mains : 230V AC

Dimension : 27CMS X 17CMS [metal cabinet]

Weight : 2KGS APPX
DIC Trainer fitted with a strong and steady stepper motor trainer, flow transmitter trainer,
speed control of DIC motor, and A/C positioning servo system. These trainers features such
as excellent functionality, low maintenance and easy installatio





Power circuit with a DC shunt motor 2SCRs/4SCRs and 2 power diodes
A circuit breaker
A bridge rectifier for field supply
1 phase converter firing ckt
SCR converter with open/close loop with motor rpm indication, mech. Loading load
regulation = 1% with tacho F/B
PULSE AMPLITUDE MODULATION & DEMODULATION
To construct a PAM using IC timer and to observe the operation of single and dual polarity
PAM these output can control a CMOS sampling switch by adding dc reference level to the
input you can able to observe the single polarity PAM and by removing the dc level you able
to observe single polarity PAM to observe the demodulated output using detector circuit
Technical Specifications:

Built in power supply : +12VDC
Govt.Polytechnic Takhatpur
24
55
Cyclo
converter

Mains : 230V AC

Dimension : 27CMS X 17CMS [metal cabinet]

Weight : 2KGS APPX
converting single fixed frequency AC signal to Variable frequency AC signal. This is
achieved by using a center tap transformer. Four different SCRs used. Appropriate snubber
circuits protect these SCRs. Volt meter and Current meters for the measurement of voltage
and current within the circuit.
 CIRCUIT BREAKER TIME INTERVAL METER Input Voltage: 230V AC , 50HZ
single phase.
Front Panel Indication & Controls:






Power On Switch : Provided Switch On The Timer
Key Bord : Provided Test Operation
R-S232 Port : Provided Connect The Computer
Timer Sense : Closed, Trip, C/o & Bounce Time
Display : Digital LCD Type
Output Termination : Provided To The Rear Side 3pole With Com + Close, Trip Coil
Connection
Features:
56
Chopper
Circuit Kit







Fully digital micro base control key board operation
Close, trip , c-o, bounce time on key board operation
Real time and date pass word protected
Storage 100 test reading , Re- call facility
R-S 232 connected
Thermal printer for test operation print
Work on live switch yard. Induction protected
Accessories:





57
Parallel

Inverter kit 
Breaker Timer
Printing Roll
Test Probe
Input Supply Cord
Operating Manual
Kit Working voltage:(220-240)VAC
Input Voltage:30 V DC
Govt.Polytechnic Takhatpur
25









o

o
Output Voltage:30 V AC
Output Current:1 Amps
Output Frequency:0- 50Hz
Bundle Contents
Single Phase Parallel Inverter Module
Patch cards
6A power supply card
2A Fuse
Manual
Accessories
RHEOSTAT R-LOAD
Value 0-200 Ohm 2 A
INDUCTOR L-LOAD
Value 0-120mh Multitapping
- See more at: https://www.pantechsolutions.net/products/power-electronics/parallelinverter#sthash.50NgRaWM.dpuf
HIGH VOLTAGE TEST KIT Technical Specification



Type: 72 KV DC high voltage test kit
Input:230V AC 50 HZ
Out put:zero to 72 KV DC 10 mA
Control
58
PUT Trainer
Kit







Power on: Provided indicator switch
On - off: Provided indicator push button
Volt meter: Show on zero to 72 KV DC
Current meter: Show on likege current zero to 10mA
Protection: LT & HT trip protection over load trip protection with indicator trip level
1, 5, 10 Ma
Timer: Set testing time 1min, 2min,and 5min.
Connection: Polarity connector probe in put & out put
Title: Electronics Devices & Circuits Lab
S.
No
.
Name of the Equipment
to be procured
Govt.Polytechnic Takhatpur
Specification (Enclosure Reference)
26
59
Oscillator Trainer Kit
CRO
60
61
Hw/Fw Rectifier Trainer
Kit
62
Bridge Rectifier Trainer
Kit
63
UJT Trainer Kit
64
Voltage Series ,current
Series Amplifier
65
RC Phase Shift
Oscillator
Fixed DC supply of +5V/500mA One LED indicator to indicate Power input.
On-board Circuits
a. Hartley Oscillator circuit
b. Colpitt’s Oscillator circuit
c. Blocking Oscillator circuit
d. Clapp Oscillator circuit
All interconnections are made using 2mm banana
Patch cords.
1. Power supply requirement
: 230V AC, 50 Hz.
2. WITH FAULT GENERATION AND TEST POINTS ON P.C.B.
3. WITH Built in regulated Power supply 3. WITH CRT
4. WITH SAPERATE HORIZONTAL ,VERTICAL AND POWER SUPPLY
SECTIONS be printed on PCB for easy calculation.
5. Standard Accessories :
1. User Manual with practical and circuit diagrams in two copies.
2. Connecting patch cords - sufficient nos.
Built in power supply 0-12V. 150mA continuously variable. Power supply
requirement-230V-250V Ac, 10%,50Hz Semi Conductor diodes Fabricated on
PCB Accessories:- I. Manual having practical details, 2mm patch cord
Built in power supply 0-12V. 150mA continuously variable. Power supply
requirement-230V-250V Ac, 10%,50Hz Semi Conductor diodes Fabricated on
PCB Accessories:- I. Manual having practical details, 2mm patch cord
 Kit Working voltage :(220-240)VAC
 Input Voltage
:110 V AC
 Input Current
:2A
 Frequency
:50/60Hz
Amplifiers of model which are known for their minimum harmonic distortion
and high sound clarity. These amplifiers have separate gain control for each of the
4 inputs and have frequency response of 40Hz-18, 000 Hz +-2dB. AC power
supply of Single Phase 240 V, 50 Hz +- 10% is required to run these amplifiers.
Technical Specification Pa-6000 Booster Amplifier Input power Supply
a) AC Mains Operation
b) Battery Operation Single Phase 240 v, 50 Hz +- 10%... Housing It is mounted
in an elegant...
DC supply 12 V @ 500 mA
* On panel circuit diagram of RC phase shift oscillator,
* Required numbers of patch cords and operating manual. * Wood Box (Closed
Type)
Title: Digital Electronics Lab
S.
No.
66
Name of the Equipment
to be procured
Digital Logic GATE
Trainer Kit
Govt.Polytechnic Takhatpur
Specification (Enclosure Reference)
a.
b.
c.
d.
Inbuilt +5V/300mA power Supply with shot circuit Protection
input line & output lies Toggeles Switches.
TTL Compatibility.
Voltage Level Indication By LED’s.
27
67
Flip Flop Trainer Kit
(JK,D,T F/F)
68
Digital IC Trainer Kit
69
Demorgan Theorem
Trainer Kit
70
Counter Trainer Kit
71
Logic Gates Trainer (
Govt.Polytechnic Takhatpur
e. Training manual & connecting patch cords.
On Board required Integrated Chip Should demonstrates the working
characteristics of basic digital gates using IC and Verification of truth table of
each gate One gate of each variety (NOT, OR, AND, NOR, NAND, EX-OR, EXNOR) - Bank of Logic Inputs – Two separate Hi/LO Inputs with Switch, LED
Indicator & Output terminal respectively. - Bank of Logic Outputs – Two separate
Outputs with Input Terminal & LED Indicator respectively
Set of necessary patch cords - Housed in an elegant cabinet with a well spread
intelligently designed multicoloured layout on the front panel - Strongly
supported by a comprehensive instruction manual complete with theory and
operating details - Built - in DC regulated power supply with short circuit
protection & LED indication for supply “ON” to work on 230V AC Mains
a. Inbuilt +5V/300mA power Supply with shot circuit Protection
b. input line & output lies Toggeles Switches.
c. TTL Compatibility.
d. Voltage Level Indication By LED’s.
e. Training manual & connecting patch cords.
On Board required Integrated Chip
All flip-flops
DC power supply +5 V, Logic level high +5V,low 0V,
Dual 0-5 V on board power supply ,IC-7404,IC-7432,IC-7408,IC-7402,IC7400,IC-7486 ,logical Gates, flip-flops, 20 PIN ZIF socket
Study of basic gates and verification of their truth tables (NOT, OR, AND, NOR,
NAND,
EX-OR, EX-NOR)
• Study and verifications of the laws of Boolean Algebra and De-Morgan's
Theorems
• Study of important TTL terminologies. Verification of important TTL circuit
parameters
• Construction and verification of various types of flip -flops using gates & IC's
(RS, JK, D, T, M / SJK)
• Construction and verification of various types of combinational circuits such as
Half Adder, Full Adder, Half Subtractor, Full Subtractor, Even / Odd Parity
Checker, Multiplexer, Demultiplexer, Binary to Gray & Gray to Binary
Converters
• Construction and verification of various types of Up / Down, Synchronous /
Asynchronous, Ripple / Reverse, Ring, Binary, BCD & Decade Counters
• Construction and verification of 4 Bit Universal Shift Register (SR / SL
operation).
• Study of 7 -segment display and decoder / driver DC Regulated Power Supply :
5 V / 500 mA (IC based)
Clock Generators (TTL, 5V) :
Demorgans Theorem
DC power supply +5 V, Logic level high +5V,low 0V
Built-in power supply DC +5 V @ 500 mA
B. 4 Logic input switches with green LED displa
C. 4 Logic output red LED display
D. On panel diagram with ICs
E. Required numbers of patch cords and operating manual
Up down counter
DC power supply +5 V, Logic level high +5V,low 0V,
 OUTPUT D.C. VOLTAGE : Fixed 5V ±1%
.
28
ND,NOR, NOT,
NAND,Ex-OR,Ex-NOR)










OUTPUTCURRENT : 1 Amp.
LOAD REGULATION : ±1% of the highest specified output voltage.(NO
LOAD TO FULL LOAD)
LINE REGULATION (For ±10% change : less than 50 mV. in mains
Voltage i.e. 230V)
RIPPLE AND NOISE : less than 5 mV.
CLOCK INPUT DEVICE : Clock pulse of 1 second.
DEBOUNCED LOGIC SWITCH (HI/LO) : Four nos. Input voltage of HI
level ³ 2.25V. Input voltage of LO leve £ l 0.8V.
4 BITS LED OUTPUT INDICATOR : Maximum input voltage less than or
equal to 5V D.C.
SOLDER LESS BREAD BOARD : Bread Board having one main strip,
total interconnected 640 tie points for ICs and half main strip, total
interconnected 320 tie points for power supply, Clock, Input and output
state. Each strip having length 173mm and accepting dia 0.56mm/24SWG
recommended, use only 22-26 SWG wire for interconnections.
BASIC LOGIC GATES & : Four AND gates, Four OR gates, Four NAND
gates, Four NOR gates, Six NOT FLIP FLOP UNITS gates, Dual J-K flipflop, J.K. master/slave flip-flop & Dual D-type flip flop.
APPLICATIONS : Verification of AND, OR, NOT, NAND, NOR Gates &
their truth table. Verification of Boolean Algebra. The half-adder and fulladder design. Verification of D-type flip-flop and truth table. Verification
of JK flip-flop and truth table. Verify cation of Dual JK Master/Slave flipflop and truth table.
Title: Electrical & Electronics Measurement Lab
S.
No
.
Name of the Equipment
to be procured
72
CRO
73
Digital Frequency Meter
74
Digital Panel meter
Govt.Polytechnic Takhatpur
Specification (Enclosure Reference)
1. Power supply requirement : 230V AC, 50 Hz.
2. WITH FAULT GENERATION AND TEST POINTS ON P.C.B.
3. WITH Built in regulated Power supply 3. WITH CRT
4. WITH SAPERATE HORIZONTAL ,VERTICAL AND POWER SUPPLY
SECTIONS be printed on PCB for easy calculation.
5. Standard Accessories :
1. User Manual with practical and circuit diagrams in two copies.
2. Connecting patch cords - sufficient nos.
Voltage: 200mV to 500V
* Current: 200μA to 5A
* Accuracy: 0.1%
meters are available in Size 96 X 96 mm. Digital Panel Meters are available in 4½
digit and 3½ digit.
Technical Specifications of Digital Panel Meters :
Sr. No. Description Accuracy Size 01 3½ Digital DC Voltmeter ±(0.5% rdg + 1
dgt ) 48x96x90 02 3½ Digital DC Ammeter ±(0.5% rdg + 1 dgt) 48x96x90 03 3½
Digital AC...
29
75
76
Digital Multimeter
Digital Storage
oscilloscope
Govt.Polytechnic Takhatpur
Display : 4½ digit LCD display (19999 Counts)
digit LCD display 70* 50 mm, Battery 9 V, Max Display 3999, measure DCV
(1000 V) ACV 750 , DCA 400mA , Resistance , Freq ,Test diode, Transistor and
Continuity
Digit Size : 17mm(H), CE approved., Over range Indication, '1’ Most
Significant Digit is shown on display., DATA HOLD facility, Auto Power Off,
Polarity: Automatic (-) negative polarity indication
Resistance, Diode test & Audible Continuity, Logic test, Frequency, & Duty
Cycle Function.
Accessories : Test Leads, Carrying Case, User Manual, Battery
Bandwidth 200/300MHz
Compact Oscilloscope
7” Colour Display
FFT Function
2 GSa/s Sample Rate
Large no. of Auto Measurements (32 nos.)
Built in Multimath Function +, –, ×, FFT
Cursor Measurement : Auto, Manual, Track
Pass / Fail Function
USB Host / Device
Realtime Sample Rate 2 GSa/s (Single Channel)
Equivalent Sample Rate 50 GSa/s
Number of Channels 2 CH
Memory Depth 24 Kpts
Acquisition Modes Normal/Average/Peak Detect
Average Selectable from 4 to 256
Vertical Sensitivity 2 mV/div to 5 V/div (1-2-5 Sequence)
Vertical Resolution 8 bits
Rise Time <1.7ns <1.2ns
Input Impedance 1MV II 13pF
Input Coupling DC, AC and GND
Maximum Input Voltage ±400Vpp
Timebase Range 2.5ns - 50s/div 1ns - 50s/div
Time Base Accuracy ±100 ppm measured over 10ms interval
Trigger Sources CH1, CH2, Ext, Ext /5, AC Line
Trigger Modes Auto, Normal, Single
Trigger Type Edge, Pulse Width, Slope, Video, Alternate
Trigger Coupling AC, DC, LF rej, HF rej
Auto Measure
Cursor Measure Manual, Track and Auto measure mode
Maths +, – , ×, FFT
Digital Filter High Pass, Low Pass, Band Pass and Band Reject
Waveform Interpolation Sin x/x, Linear
Storage Internal 2 Group Reference Waveform, 20 Setups, 20 Waveforms
USB
Communication Port USB Host, USB Device, RS232, Pass/Fail output
Sample Types Real Time and Equivalent Time
FFT Window: Hanning, Hamming, Blackman, Rectangular
Persist Off, 1 sec, 2 sec, 5 sec, Infinite
Menu Display 2 sec, 5 sec, 10 sec, 20 sec, Infinite
Probe Attenuator 1X, 10X
Measure Display Modes Main, Window, Window Zoom, Scan, X-Y
Display 7” Colour (64K) TFT-LCD
30
77
Oscillator
Display Resolution 480 Horizontal x 234 Vertical pixels
Power 100 - 240V AC, 45Hz - 440Hz, 50VA Max
Net Weight 2.4 kg
Dimensions 399 x 110.5 x 148.5 mm
OSCILLATOR 1MHZ :Specification
* FREQUENCY RANGE : 1Hz to 1 MHz in 6 Decade Range.
* DIAL ACCURACY : + 3% of Range.
* WAVE FROM : SINE & SQUARE WAVE.
* OUTPUT VOLTAGE :
* Sine Wave 0-10V in 3 Decade Step of 10V IV & 0.IV with Consciously
Variable control.
* Square Wave 0-15V P/P Continuously Variable.
* SINE WAVE DISTORSION : Less than 0.5% from 100Hz to 100KHz.
* SQUARE WAVE RISE TIME : Less than 100 nano seconds at maximum
output.
* SQUARE WAVE...
Title: Network Analysis Lab
S.
No
.
78
79
80
Name of the Equipment to
be procured
Specification (Enclosure Reference)
Four Digital Meters DC Volt and Current Meter.
2. DC Power Supply +12V Regulated, +5V Regulated,
0-10V Variable, 0-5V Variable.
3. One Step Down Transformer (9-0-9V).
4. Five Potentiometers (330W, 1K, 4.7K, 10K, 47K).
5. One PNP Transistor CK-100 and one NPN Transistor CL-100.
6. One FET BFW10.
KCL & KVL Trainer Kit
7. +5V Regulator IC 7805.
8. Different types of diodes (In4007, Oa79, 6V Zener).
9. 34 Resistance of Different Values.
10.Six Capacitors of Different Values. offering Verification of KCL / KVL. High
performance
* Dimensional accuracy
* Accurate results
. Four Digital Meters DC Volt and Current Meter.
2. DC Power Supply +12V Regulated, +5V Regulated,
0-10V Variable, 0-5V Variable.
3. One Step Down Transformer (9-0-9V).
Super Position Theorem
4. Five Potentiometers (330W, 1K, 4.7K, 10K, 47K).
Trainer Kit
5. One PNP Transistor CK-100 and one NPN Transistor CL-100.
6. One FET BFW10.
7. +5V Regulator IC 7805.
8. Different types of diodes (In4007, Oa79, 6V Zener).
9. 34 Resistance of Different Values.
10.Six Capacitors of Different Values.With Lead, Patch Card & Manual
1. Four Digital Meters DC Volt and Current Meter.
Maximum Power Transfer
2. DC Power Supply +12V Regulated, +5V Regulated,
Theorem Trainer Kit
0-10V Variable, 0-5V Variable.
3. One Step Down Transformer (9-0-9V).
Govt.Polytechnic Takhatpur
31
81
Active Filter Trainer Kit
4. Five Potentiometers (330W, 1K, 4.7K, 10K, 47K).
5. One PNP Transistor CK-100 and one NPN Transistor CL-100.
6. One FET BFW10.
7. +5V Regulator IC 7805.
8. Different types of diodes (In4007, Oa79, 6V Zener).
9. 34 Resistance of Different Values.
10.Six Capacitors of Different Values.. With Lead, Patch Card & Manual
On Board Function Generator- Output Waveform-Sine
Frequency and Amplitude Adjustment is provided using Potentiometers One LED
indicator to indicate Power Input.
On-board Circuits
a. Inverting Low Pass Filter
b. High Pass Filter
c. Non-Inverting Low Pass Filter
d. Unity Gain Phase Shift
Supply Connections to OP Amp(±12V) Internally Provided to the circuit All
interconnection are made using 2mm Patch cords for interconnections.
Title: Basic Electrical and Electronics Lab
S.
No
.
Name of the Equipment to
be procured
Specification (Enclosure Reference)
The
board
consists
of
the
following
built-in
parts:
01. 0-15 VD.C. at 100 mA, continuously variable regulated Power Supply.
02. D.C. Voltmeter, 65mm rectangular dial to read 0-15V D.C.
03. D.C. Milliammeter, 65mm rectangular dial to read 0-50mA D.C.
04.
Adequate
no.
of
other
electronic
components.
05. Mains ON/OFF switch, Fuse and Jewel light.


82
Ohms law




83
Rheostat
Govt.Polytechnic Takhatpur
The unit is operative on 230V ±10% at 50Hz A.C. Mains.
Adequate no. of patch cords stackable from rear both ends 4mm spring
loaded plug length ½ metre.
Good Quality, reliable terminal/sockets are provided at appropriate places on
panel for connections/observation of waveforms.
Strongly supported by detailed Operating Instructions, giving details of
Object, Theory, Design procedures, Report Suggestions and Book
References.
Weight : 3 Kg. (Approx.)
Dimension : W 340 x H 110 x D 210

Input Voltage: 10-300V

Input Current: 0.01 to1 A / 0.05 to 5A / 0.1 to 10A

Accuracy: Class 0.5

Resolution: Floating Decimal Point
32
84
85

Panel Dimensions: 96 X 96 X 85 mm

Auxiliary: 230 V +_ 20%

Applicable at all Power Factor
meters are available in Size 96 X 96 mm. Digital Panel Meters are available in 4½
digit and 3½ digit.
Technical Specifications of Digital Panel Meters :
Sr. No. Description Accuracy Size 01 3½ Digital DC Voltmeter ±(0.5% rdg + 1
dgt ) 48x96x90 02 3½ Digital DC Ammeter ±(0.5% rdg + 1 dgt) 48x96x90 03 3½
Digital AC...
Multifunction meter with TRMS measurement, measures distorted waveform up to
15thharmonic, measures upto 18 electrical parameters in a 3phase network (V, I, F,
In, System KVA, I Demand, I Max Demand, kVA Demand, kVA Max Demand)
series test, parallel test,
multimeter, mager,
ammeter, voltmeter,
wattmeter, earth test
equipment
Transformer Functioning
Kit
DIGITAL MULTI FUNCTION METER
Input Voltage : 5 - 300
VInput Current : 0.01 to 1A / 0.05 to 5A / 0.1 to 10A ( Any one range)
Accuracy : Class 0.5 (For P.F. ± 0.02)
Resolution : Floating Decimal Point
Auxiliary : 230V ± 20%
Display : 16 by 2 Alphanumeric LCD
Parameters : V , A , P.F. , W , VA
Dimension : DPM - 48 X 96 (Depth 110 mm)
Title: Fundamentals of Electrical Engg. Lab
S.
No
.
Name of the Equipment to
be procured






86
Transformer Functioning
Trainer Kit






Govt.Polytechnic Takhatpur
Specification (Enclosure Reference)
Two moving iron 72 x 72 mm AC Voltameter 0 300 V
One moving iron 72 x 72 mm AC Voltmeter 0 50 V
Two moving iron 72 x 72 mm AC Ammeter 0 5 Amp
One moving iron 72 x 72 mm AC Ammeter 0 1Amp
Wattmeter single phase, dynamometer type current coil 0.4 Amp. Potential coil
250 Volt 100W
Wattmeter single phase, dynamometer type current coil 4 Amp. Potential coil 250
Volt 1000W
Auto transformer input 230V, output 0270V at 5 Amp
MCB: 6Amp
Load: Two 100W Bulb Provided for Load. & three pin Socket for external Load
Provided
The unit is operative on 230V ±10% at 50Hz AC Mains
Set of connecting wires
Strongly supported by detailed Operating Instructions, giving details of Object,
33
Theory, Design procedures, Report Suggestions and Book References
Transformer:



Rating: 1 KVA
Primary Voltage: 0 - 125 V, 0 - 125 V
Secondary Voltage: 0 - 125 V, 0 - 125 V

Switching Power Supply MAIN FEATURES - High Efficiency - Single Phase and
Three phase - Unversal AC / DC Input - DIN Rail, Low Profile and Enclosed types
- 5W to 960W , 5 to 48VDC output - Overload and Short circuit protection builtin
Features:
* Multi-functions: Watt, ACV, ACA, DCV, DCA
* 18 mm, large size LCD display
* LSI circuit provides high accuracy
* True AC power measurement
87
Various Power Supply
88
Wattmeter Trainer Kit 




89
Digital Multi meter
Display: 3½ digits LCD
Line Voltage : 230V AC ±10%, 50 Hz
Meter Constant : 1600 impulses/KWh (On LED)
Display Counter : 100 impulses /KWh (On LCD)
Maximum Current : 30 A
Shunt : 350 mW
Direct and alternating voltages from 100mV ... 1000V
Direct and alternating currents from 10mA ... 10.00A
* Resistances from 100mW... 40.00MW with zero correction
Capacitance from 1pF ... 200.00mF with zero correction.
Frequencies from 10.00Hz ... 500.0kHz
Diode measurement and continuity testing
Hold measurement.
Relative measurement
and television service, training and education.
Temperature Measurement
Title: Electronics Materials & Workshop
S.
No
.
90
Name of the Equipment to
be procured
Various Resistor/
Capacitor/Inductor
Display Trainer Kit
Govt.Polytechnic Takhatpur
Specification (Enclosure Reference)
Automatic component type detection: Inductor, Capacitor or Resistor.
- Automatic test frequency selection: DC, 1kHz, 15kHz and 200kHz.
- Inductance from 1uH to 10H.
34
91
Solder/De-solder
Machine & Material
92
LCR Meter
93
Various Opening Tool kit
(Screw Driver etc.)
- Capacitance from 1pF to 10,000uF.
- Resistance from 1Ohm to 2MOhm.
- Inductance measurement also shows DC winding resistance.
- Test frequency displayed for all measurements.
- Typical accuracy of 1.5% for inductors and capacitors (see spec table for details).
- Typical accuracy of 1% for resistors.
- Test lead complete with gold plated 2mm plugs and sockets.
- Supplied with removable gold plated hook probes.
Sharang 604D Micro Processor Based Digital Soldering & De-Soldering Station:
* Easy to handle.
* Different Sized Bits & Nozzles.
Material-Amtech wire roll solder in both lead and lead free.
Digital Lcr Meter specifications:- Inductance(L)
Capacitance/Resistance/Inductance Range Accuracy Resolution Measuring
frequency 2mH ±(2.0%+5d) 1uH Approx:200Hz 20mH 10uH 200mH 100uH 2H
±(5.0%+5d) 1mH 20H ±(5.0%+15d) 10m...
Tool Kit which is used for multiple applications
Title: IPC Lab
S.
No
.
Name of the Equipment to
be procured
Specification (Enclosure Reference)
output of 1V AC RMS
nominal
-in power supplies
94
LVDT Kit
polarity indicator
et.
-Y recorder with 200mV DC FSD
(±100mV)
configuration.
move.
side of the strip.
95
Strain Guage Kit
the strain gauge foil: 10mm
-in power supply.
supplied.
Govt.Polytechnic Takhatpur
35
96
Thermo Couple Kit
97
Resistance Couple
Detector
thermocouples for measuring temperatures from 150°C to 1600°C and, are highly
accurate and sensitive
temperature measuring between -200ºC to +600ºC in this temperature range.
-position selector switch is used to check the output from each
transducer.
98
Piezoelectic Transducer
ctly from signal conditioner, b) from sample and hold also.
-in power supply.
99
LDR Kit
Features : Instrument comprises of DC Regulated Power Supply 0-3VDC/150mA,
two round meters for voltage & current measurement, LDR mounted in a metal
Box, connections of Supplies & LDR brought out at 4mm Sockets. Lamp Holder
with100 W Bulb & 50 cm wooden plank are given with this apparatus.
PRINCIPAL
GOVT. POLYTECHNIC TAKHATPUR
DIST. BILASPUR (C.G.)
Govt.Polytechnic Takhatpur
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement