Smeg SOU130S 30 Inch Wall Oven Installation instructions

INSTALLATION INSTRUCTIONS
INSTRUCTIONS POUR L’INSTALLATION
INSTRUCCIONES DE MONTAJE
BUILT-IN OVEN
FOUR ENCASTRABLE
HORNO EMPOTRADO
1-6
ENGLISH
THANK YOU FOR YOUR TRUST AND FOR BUYING THIS APPLIANCE.
PLEASE READ THIS MANUAL CAREFULLY. IT CONTAINS ALL NECESSARY INSTRUCTIONS TO CONVERT
THE GAS SUPPLY OF THIS PRODUCT.
7 - 12
FRANÇAIS
NOUS VOUS REMERCIONS DE VOTRE CONFIANCE ET DE L’ACHAT DE CET APPAREIL.
S’IL VOUS PLAÎT, LISEZ CE MANUEL ATTENTIVEMENT. IL CONTIENT TOUTES LES INSTRUCTIONS
NECESSAIRES POUR CONVERTIR L'ALIMENTATION EN GAZ DE CE PRODUIT.
8 - 18
ESPAÑOL
GRACIAS POR LA CONFIANZA QUE HA DEPOSITADO EN NOSOTROS CON LA COMPRA DE ESTE
APARATO.
LEA ESTE MANUAL ATENTAMENTE. CONTIENE LAS INSTRUCCIONES
CONVERSIÓN DEL SUMINISTRO DE GAS DE ESTE PRODUCTO.
NECESARIAS
PARA
LA
IMPORTANT:
Save for the local electric inspector's
use
IMPORTANT :
Conserver pour
électricité
Installer: Leave installation instructions
with the homeowner
Homeowner:
Keep
installation
instructions for future reference.
Installateur : Laisser les instructions
pour l’installation au propriétaire
Propriétaire : Garder les instructions
pour l’installation pour référence future.
Instalador: Dejar las instrucciones de
montaje al propietario de la casa
Propietario de la casa: Guardar las
instrucciones de montaje para futura
referencia.
Write down the model and serial
numbers before installing the
range.
Both numbers are found on the
model/serial ID plate, located on
the oven door frame.
Notez le numéro de modèle et le
numéro de série avant d'installer
la cuisinière.
Les deux numéros se trouvent
sur la fiche signalétique du
modèle et du numéro de série,
située sur le cadre de la porte du
four.
Anote el número de modelo y de
serie antes de instalar la cocina.
Ambos números aparecen en la
placa de identificación del
modelo/serie, ubicada en el
marco de la puerta del horno.
l’inspecteur
en
IMPORTANTE:
Guardar estas instrucciones para uso
del inspector local de electricidad
Model # _______________________ No Modèle ____________________ Modelo # ______________________
Serial # _______________________ No Série _____________________ Nº de serie # ___________________
OVEN INSTALLATION MANUAL
ENGLISH
TABLE OF CONTENTS
page
I ntroduc tion
1
Installation notes
2
Tools you will need
1
Wall or under counter installation, single oven
3
Electrical connections
6
Power requirements
1
Wall installation double oven
3
3-wire branch circuit
6
page
page
Connecting to 120/208V circuit
5
Choosing oven location
1
F lus h ins ta lla tion
4
4 -wire bra nc h c irc uit
6
Steps for installation
1
Electrical supply
5
Final check list
6
Technical data
2
Wiring requirement
5
IMPORTANT: Save these instructions for the local electrical inspector use.
INSTALLER: Please leave this manual with owner for future reference.
OWNER: Please keep this manual for future reference.
WARNING
a fire or explosion may result causing property damage,
If the information in this manual is not followed exactly,
personal injury or death.
INTRODUCTION
POWER REQUIREMENTS
Please read these instructions COMPLETELY AND
CAREFULLY . They will save you time and effort and help to
ensure optimum oven performance.
Be sure to observe all WARNINGS. These installation
instructions are intended for use by a qualified installer.
In addition to these instructions, the oven shall be installed:
In the United States, in accordance with the National
Electric Code/State and Municipal codes and/or local
codes.
In Canada, in accordance wi th Canadian Electric
Code C22.1-latest edition/Pro vincial and Municipal
codes and/ or local codes.
These shall be carefully followed at all times.
NOTE: IF INSTALLING YOUR OVEN IN
CANADA PLEASE CHECK TO MAKE
SURE THAT YOU HAVE A MODEL
WITH THE US AND CANADIAN LISTING
The oven must be supplied with the proper voltage and
frequency. The oven is manufactured to be connected to a
three-wire or four-wire, single phase, 120/240 Volt, 60 Hz AC
electrical supply on a sepa rate circuit fused on both sides of
the line. If a 120/208 Volt circuit must be used, see Connecting to
120/208 Volt Circuit, in this manual. A circuit breaker or time delay
fuse, sized not to exceed the circuit rating of the appliance
specified on the rating plate located on the frame behind the
door of the oven is recommended (see figure at page 5).
MARK, AS SHOWN ABOVE:
Mark as shown above means the oven complies with both
US and CANADIAN Standards.
TOOLS YOU WILL NEED
The following tools are needed to install your new oven:
Tape measure and straightedge or ruler
Pencil
Phillips screwdriver
Level
Wire cutters and wire stripper
Hand or saber saw
1” (2,5cm) Hole saw
Drill and drill bit
Safety gloves and goggles
Volt meter (0-250VAC)
PACKAGING
Remove all tape and packaging before using the oven.
Destroy the packaging after unpacking the oven following
the rules in force in your town. Never allow children to play
with packaging material.
The oven must be supplied with copper or alumimum wires.
If aluminum wire is provided to connect oven to branch
circuit, UL listed connectors for joining copper and aluminum
must be used. Follow instructions provided with connectors.
It is recommended that you have the electrical wiring and
hook-up of your oven performed by a qualified electrician.
After installation is complete have the electrician show you
where the main disconnect is and which of the circuit
breakers/fuses are for the oven.
CHOOSING OVEN LOCATION
Carefully select the location where the oven will be placed.
The oven should be located for convenient use in the
kitchen, but away from strong drafts.
Strong drafts may be caused by open doors or windows, or by
heating and/or air conditioning vents or fans. Make sure that
electrical power can be provided to the location selected.
STEPS FOR INSTALLATION
The following pages provide the necessary information for
proper installation of the oven and are arranged as follows:
Technical Data
Installation Cutout Dimensions, Required Clearances and
Mounting instructions for:
- Under counter Installation, Single Oven
- Wall Installation, Single Oven
- Wall Installation, Double Oven
Electrical Supply and Wiring Requirements, Programming
required if connecting to 120/208 Volt Circuit. Electrical
Connections for 3-wire or 4-wire Branch Circuit.
Final Checklist
1
OVEN INSTALLATION MANUAL
ENGLISH
TECHNICAL DATA
Electrical Ratings and Maximum Connected Load
For cutout dimensions see following section titled:
Preparing location
@ 120/240 Volts 60Hz
SINGLE OVEN
Amperes
SOU330X
16,9
DOUBLE OVEN
UPPER CAVITY
3,84
Amperes
kW
@ 120/208 Volts 60Hz
Amperes
kW
17,5
3,54
Amperes
kW
LOWER CAVITY
33,8
DOU330X
kW
7,68
32,4
6,48
INSTALLATION NOTES
1.
Do not slide oven across floor. Damage to floor covering
or floor could result.
The oven support surface must be a minimum 3/4" (2cm)
thick plywood platform.
For single ovens, it must support 202 pounds.
For double ovens, it must support 379 pounds. The
platform must be solid, level and flush with the bottom of
the cabinet cut out.
Use extreme caution when moving or installing the oven.
It is very heavy.
DO NOT LIFT THE OVEN BY THE DOOR HANDLE,
remove the door for easier handling and installing.
See REMOVING THE DOOR in the maintenance section
of the Use Care Manual.
Be very careful when moving or installing the oven to
avoid damage to the oven frame or damage to the cabinets.
Be sure to level the oven. An oven that is not level may
provide poor or inconsistent baking results.
Be careful when placing oven. DO NOT pinch the conduit
between the oven back.
2.
3.
4.
5.
6.
Ltr.
DIMENSION
A
Cutout Width
B
Cutout Depth
C
Cutout Height
D
Floor Bottom of Cutout
E
Minimum Spacing
2
WARNING
Before installing or removing, turn power OFF at the service
panel. Lock service panel to prevent power from being turned
ON accidentally.
Securely fasten oven to cabinet using the screws provided.
Failure to do so could result in oven moving or tipping
during use and causing damage to the oven or cabinets or
personal injury.
Know how to disconnect the power to the oven at the circuit
breaker or fuse box in case of an emergency.
CAUTION
Unit is heavy and requires
equipment to move.
at least two people or proper
SINGLE
30”
DOUBLE
30”
28 7/16”
(72,2 cm)
24”
(61 cm)
27 3/8”
(69,5 cm)
34”
(86,5 cm)
1/2”
(1,3 cm) min
28 7/16”
(72,2 cm)
24”
(61 cm)
49 3/4”
(126,5 cm)
N/A
1/2”
(1,3 cm) min
OVEN INSTALLATION MANUAL
ENGLISH
WALL OR UNDER COUNTER INSTALLATION, SINGLE OVEN
Electrical
supply
junction
box
Electrical
supply
junction
box
Secure oven to cabinet using the screws provided.
Screws should be inserted through the mounting holes
in the positions indicated in the frame (open door to see
frame and mounting holes). Do not over tighten screws.
WALL INSTALLATION, DOUBLE OVEN
Electrical
supply
junction
box
Secure oven to cabinet using the screws provided.
Screws should be inserted through the mounting holes
in the positions indicated in the frame (open door to see
frame and mounting holes). Do not over tighten screws.
3
OVEN INSTALLATION MANUAL
ENGLISH
FLUSH INSTALLATION
Ltr.
4
DIMENSION
F
Cutout Width
G
Cutout Height
H
Visible part of the mounting strips
SINGLE
30”
30 1/16”
(76,4 cm)
28 1/32”
(71 ,2 cm)
3/4”
(1,9 cm)
DOUBLE
30”
30 1/16”
(76,4 cm)
51”
(129,5cm)
3/4”
(1,9 cm)
OVEN INSTALLATION MANUAL
ENGLISH
ELECTRICAL SUPPLY
CONNECTING TO 208 VOLT CIRCUIT
Before installing the oven have a qualified electrician
verify that your home is provided with adequate
electrical service and that the addition of the oven will
not overload the branch circuit on which it is to be
installed.
A separate three-wire or four-wire single phase,
240 Volt, 60 Hz, or a 208 Volt, 60Hz branch circuit is
required.
NOTE : FOR USE WITH 208 V, 60 HZ SUPPLY
VOLTAGE, SEE CONNECTING TO 208 VOLT
CIRCUIT.
For hook-up of the oven you will need to have an
approved junction box installed where it will be easily
reached through the front of the cabinet where the
oven will be located. The oven has 3 feet of conduit.
Allow two to three feet of slack in the line so that the
oven can be moved if servicing is ever necessary.
DO NOT shorten the flexible conduit.
This option is provided for areas where standard 240 Volt service is
not available. This option must be accessed with the oven connected
to power source, and using the following sequence:
1. Within five minutes from power up, hold [OPTIONS] and [TIME]
keys for 3 seconds to enter the user option menu. The display
shows as follows:
2.
3.
Hold then [TIME] and [LIGHT] keys until the display becomes
dark.
Hold [OPTIONS] and [LIGHT] further, until the time display shows
“Volt” and temperature module shows “240” blinking, waiting for
an input.
Location of rating plate
4.
5.
6.
WIRING REQUIREMENTS
When making the wire connections, use the entire
length of the conduit provi ded (3 feet). The conduit
must not be cut.
Before making connections make sure the power is off
and read and observe the following:
1. A separate three-wire or four-wire, single phase,
240 Volt, 60 Hz or 208 Volt, 60 Hz branch circuit is
required for the oven.
2 . The oven must be connected with Copper or
Aluminum wire.
3. In the United States:
Wiring must conform to the National Electrical
Code, ANSI/NFPA No. 7 latest edition. You can
obtain a copy of the National Electrical Code by
writing to: National Fire Protection Association
Batterymarch Park Quincy, MA 02269
In Canada:
Wiring must conform to Cana dian Electrical Code
C22.1- latest edition. You can obtain a copy of the
Canadian Electrical Code by writing to: Canadian
Standards Association 178 Rexdale Boulevard
Rexdale (Toronto), Ontario, Canada M9W 1R3
4. Wire size (Copper or Aluminum wire) and
connections must be suitable for the rating of the
appliance as per the National Electrical Code
requirements. The flexible armoured cable
extending from the oven should be connected
directly to the junction box.
5. The junction box should be located so as to allow
as much slack as possible between the junction
box and the oven so it can be moved if servicing is
ever required.
6. A U.L. listed conduit connector must be provided
at each end of the power supply cable.
Using [INC] or [DEC] keys, the control toggles between 240V and
208V options. Hold “OPTIONS” to confirm.
Hold [TIME] and [LIGHT] keys in order to quit the selection.
Hold [OPTIONS] key for 3 seconds to quit the user option menu.
The voltage setting is stored and kept even after a long power-off.
WARNING
ELECTRICAL SHOCK HAZARD
The electrical power to the oven branch circuit must be shut off
while line connections are being made.
Do not use an extension cord with this appliance.
Electrical ground is required on this appliance. The free end of the
green wire (the ground wire) must be connected to a suitable
ground. This wire must remain grounded to the oven.
If cold water pipe is interrupted by plastic, non metallic gaskets,
union connections or other insulati ng materials, DO NOT use for
grounding.
DO NOT ground to a gas pipe.
DO NOT have a fuse in the NEUTRAL or GROUNDING circuit. A
fuse in the NEUTRAL or GROUNDING circuit could result in an
electrical shock.
Check with a qualified electrician if you are in doubt as to whether
the appliance is properly grounded.
Failure to follow these instructions could result in serious injury or
death.
CAUTION
Do not repair or replace any part of the appliance unless specifically
recommended in the manual. All other serv icing should be done by a
qualified technician. This may reduce the risk of personal injury and
damage to the oven.
Never modify or alter the construction of the appliance by removing
panels, wire covers, screws, or any other part of the product.
5
OVEN INSTALLATION MANUAL
ENGLISH
ELECTRICAL CONNECTIONS
3-WIRE BRANCH CIRCUIT (for US only)
Be sure your appliance is properly installed and grounded
by a qualified technician. Ask your dealer to recommend a
qualified technician or an authorized repair service.
This appliance is manufactured with a green GROUND wire
connected to the oven chassis. After making sure that the
power has been turned off, connect the flexible conduit from
the oven to the junction box using a U.L. listed conduit
connector. Figures A and B and the instructions provided
below present the most common way of connecting the ovens.
Your local codes and ordinances, of course, take precedence
over these instructions. Complete electrical connections
according to local codes and ordinances
“WARNING” Risk of Electric Shock, frame grounded to
neutral of appliance through a link.
Grounding through the neutral conductor is prohibited for new
branch-circuit installations (1996 NEC); mobile homes; and
recreational vehicles, or in an area where local codes prohibit
grounding through the neutral conductor. For installations
where grounding through the neutral conductor is prohibited:
x Disconnect the ground from the neutral at free end of
conduit;
x Use grounding terminal or lead to ground unit; and
x Connect neutral terminal or lead to branch circuit neutral in
usual manner.
Refer to Figure A, where local codes allow the connection of
GROUND wire from the oven to the branch circuit NEUTRAL
wire (gray or white colored wire):
x If local codes permit, connect the green GROUND wire
from the oven and the white wire from the oven to the
branch circuit NEUTRAL wire (gray or white colored wire).
x Connect the red and black leads from the oven to the
corresponding leads in the junction box.
Figure A
4-WIRE BRANCH CIRCUIT (for US and CANADA)
Refer to Figure B:
x Disconnect ground from neutral at free end of conduit.
x Connect the green GROUND wire from the oven to the
GROUND wire in the junction box (bare or green colored
wire).
x Connect the red and black leads from the oven to the
corresponding leads in the junction box.
x Connect the white wire from the oven to the NEUTRAL
(gray or white) wire in the junction box.
Figure B
x Immediately press [INC] or DEC] keys to set minutes, hold
to change by ten (10) minutes step.
To prevent improper connections leading to damage of
x Press [TIME] key or wait for a few seconds.
electrical components and so voiding the warranty, the
Clock is now set.
following steps must be performed:
5. Test the bake mode by following this step:
1. Check the electrical requirements and make sure you have x Move cooking mode knob to “BAKE” position.
the correct electrical supply and that the oven is properly
x Cooling fan, oven lights, preheat led will turn on.
grounded.
x A beep is sounded when the oven reaches the preset
2. Turn on the power supply to the oven.
350 °F (175 °C) and the preheat light turn off.
3. Check power at the junction box wires using a voltmeter
x Move the knob back to “OFF” position to stop cooking.
having a range of 0-250 VAC.
6. To check the other oven functions refer to the “Using the
If you have installed the oven for use on 240 Volt supply,
Oven Controls” section of the USE AND CARE MANUAL.
you should find that the voltage reading between the black
7. If the oven is working properly, turn off the power supply to
and red wires (Line to Line) should be 220 to 240 Volts.
the oven.
If you have modified the oven(s) for use on 208 Volt, the
8. Place the cover on the junction box and make sure the
voltage reading between the black and red wires should be
cover is securely fastened and turn on the power to the
190 to 208 Volts.
oven.
4. Set the clock by following these steps:
Leave these INSTALLATION instructions as well as the
x Press [TIME] key twice until the display shows “SET TIME”.
USE AND CARE MANUAL with the owner.
x Immediately press [INC] or DEC] keys to set hours.
x Press [TIME] key again to change minutes.
FINAL CHECKLIST
6
09SG5180 - 1-10