Graco 332226A - Bead Gun Kit for LL250SPS and LL200HS Pressurized Bead System Instructions

Kit Instructions
Bead Gun Kit for LL250SPS and LL200HS
Pressurized Bead System
For professional use only.
Model 16R963
psi (MPa, bar) Maximum Working Pressure
Important Safety Instructions
Read all warnings and instructions in the bead system
and striper manual. Save these instructions.
ti20740a
332226A
EN
Tools Needed:
Tools Needed:
•
Wrench
•
Adjustable Wrench
•
Phillips Screwdriver
•
Cutting Blade
4. Slide bead gun assembly (C) so bead outlet is horizontally level with paint tip guard and as close to
paint outlet as possible.
Gun Kit Assembly 16R963
1. If needed, configure unit gun assembly with gun arm
brackets included in Retro-fit Kit.
C
250 Models:
ti20548a
ti20709a
200 Models:
5. Install 10 in. air line (G) and push into bottom valve.
Push other end into 90° air line fitting (H) on bead
gun.
ti20569a
ti20707a
G
H
Both Models:
ti20566a
ti20708a
6. Connect bead hose (D) from gun to bead hopper.
2. See Parts diagram to assemble bead gun
accessory parts, page 5.
3. Position air switch so button (A) touches bracket (B)
when trigger is in neutral position. Tighten hardware.
A
B
ti20568a
2
D
ti20547a
332226A
Gun Kit Assembly 16R963
7. Push one end of remaining air line into top hole on
air switch and run along bead hose to tank and then
route and push into elbow fitting (J) on air tank.
8. Zip tie air and bead hoses together with supplied
ties.
1 Gun:
J
ti20979a
ti20565a
ti20980a
250 Models
2 Gun:
200 Models
9. A “Y” fitting can be used to create a dual bead gun
set up for double drop beads. Splice exit hose on
bottom of air switch and branch into both guns.
10 in.
10 in.
ti21419a
ti20564a
332226A
3
Gun Kit Assembly 16R963
0 to 8 in. Line Setup
2 Tank 1 Gun Setup
For wider lines it may be necessary to mount bead gun
as shown below.
Connect “Y” fitting as shown below to allow two tanks to
flow into one gun.
ti20977a
ti21085a
Double Drop Setup
ti20978a
Use a “Y” fitting to create a dual bead gun setup for
double drop beads. Splice exit hose on bottom of air
switch and branch into both guns.
8 - 12 in. Line Setup
ti20564a
ti21258a
4
332226A
Parts
Parts
85
71
74
75
90
78
79
91
89
84
77
82
72
80
70
73
85
83
81
90
76
ti20722a
88
Parts List
Ref.
70
71
72
73
74
75
76
77
78
79
80
Part
16T646
16T804
16T771
238329
16U274
16T829
16T816
16T803
104387
287566
111834
332226A
Description
SWITCH, air
BRACKET, switch, air
BOOT, button, push
GUN, spray, bead
HOSE, pneumatic
HOSE, bead, 3/4 in., clear
BRACKET, switch, air
ARM, gun
SCREW, mach pnh
KIT, clamp
NIPPLE, pipe, hex
Qty.
1
1
1
1
1
1
1
1
2
1
1
Ref.
81
82
83
84
85
86
87
88
89
90
91
Part
114109
116876
115483
100020
116610
103473
238665
115287
16V047
16V530
16V046
Description
Qty.
FITTING, elbow, male, swivel
1
WASHER, flat
2
NUT, lock
3
WASHER, lock
2
SCREW, mach, phil, pan, #10
3
STRAP, tie, wire
5
KIT, repair
1
FITTING, Y tube
1
HOSE, pneumatic
2
HOSE, pneumatic
1
RESTRICTOR, air flow, adjustable
2
5
Notes
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
For patent information, see www.graco.com/patents.
Original instructions. This manual contains English. MM 332226
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2012, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revision A - 2013
Notes
332226A
7
Graco Standard Warranty
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs
will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
For the latest information about Graco products, visit www.graco.com.
TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor.
8
332226A

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project