Graco 307792B AGITATOR Owner's Manual

Add to my manuals
8 Pages

advertisement

Graco 307792B AGITATOR Owner's Manual | Manualzz

INSTRUCTIONS-PARTS LIST @ fe:t7g2

ORACO

SUPERSEDES A

This manual contains IMPORTANT

WARNINGS and INSTRUCTIONS

READ AND RETAIN FOR REFERENCE

AGITATORS

71x) psi (7 bar) MAXIMUM WORKING PRESSURE l l

Model 220-355. Series A

For 5 gallon pressure tank

Model 220-357, Series A

For 10 gallon pressure tank

Model 220458, Series A

For 15 gallon pressure tank

Air driven, gear reduced, l/2 hp (373 W) air motor

2O:l ratio gear reducer: shaft rpm is l/20 of air motor rpm

TABLE OF CONTENTS

INSTALLATION .............................................

OPERATION .....................................................

SERVICE

Lubrication ......................................................

Air Motor Service ..............................................

Gear Reducer Service ........................................

2, 3

3

4

4

.5

Setting the Output Shaft Coupling.. ..................... .5

Replacing the Agitator Shaft ................................

Replacing the Coupling.. ....................................

Replacing the Shaft Seals ...................................

PARTS DRAWING .............................................

AIR CONSUMPTION CHART.. .............................

PARTS LIST .....................................................

5

.5

5

6

.6

7

HOW TO ORDER REPLACEMENT PARTS.. ............. 7

WARRANTY ......................................... Back Page

GRACO INC. P.O. Box 1441 MINNEAPOLIS,

@COPYRIGHT 1986, GRACO INC.

MN 5544011444

AIR \

RELIEF

VALVE -

AIR-

INLET

VALVE

Fig 1

2 307-792

NOTE: Reference numbers and letters in paren- theses refer to the callouts in Figures l-6 and the Parts Drawing.

WARNING

Pressure Relief Procedure

To reduce the risk of serious bodily injury, in- cluding splashing in the eyes or on the skin or in- jury from moving parts, which can result if the tank pressure is not fully relieved, always follow this procedure before opening the pressure tank cover or fill port.

1. Shut off the air supply to the tank.

2. Close the air inlet valve. See Fig 1.

3. Open the air relief valve by turning the thumb- screw counterclockwise.

4. Wait until there is no air escaping through the valve before removing the cover or opening the fill port.

5. Leave the air relief valve open until you have reinstalled the cover or fill port.

1. Follow the Pressure Relief Procedure above.

Then remove the pressure tank cover from the tank.

2. Unscrew the jam nut, and remove the jam nut, plug, and o-ring from the tank cover. See Fig 2.

3. Place the gasket (17) on top of the tank cover’s center hole. Insert the drive shaft (14) through the center hole.

VOTE: Position the air motor so it faces away from the air regulator mounting as shown in Fig 1.

Fig 2

4. Install the jam nut (16) below the tank cover.

Tighten the jam nut firmly to assure a seal between the gasket (17) and tank cover.

5. Install the support (I I) and clamp (IO) onto the shaft housing (9).

6. install the agitator paddle (12) on the drive shaft

(14). See Fig 3. a. Models 220-357 and 220-358

Align the top of the paddle hub (A) with the mark (C) on the drive shaft (141, and firmly secure the paddle (12) with two setscrews (13). b. Model 220-356

If a 5 gallon pail is to be placed inside of the pressure tank (5 gallon tank only), align the top of the paddle hub (A) with the upper mark (6) on the drive shaft (14). If a pail will not be plac- ed inside the tank, align the top of the hub (A) with the lower mark (Cl on the drive shaft (14).

7. Slide the baffle (23) over the pressure tank supply tube (El. Position the baffle about l/2 in. above the highest point on the agitator paddle (12). Secure the baffle with the two screws (24) and nuts (251. See

Fig 3.

8. Connect the air hose (21) to the pressure tank’s air inlet manifold (F). See Fig 4.

9. Remove the gear reducer’s oil level plug (G) from the street elbow and check the oil level in the reducer housing. See Fig 4. The oil should never be higher than the oil level plug. If necessary, drain or add oil until the proper oil level is attained. Screw the oil level plug back onto the street elbow.

NOTE: Special high temperature synthetic gear oil is required for the gear reducer. Use only

Grace oil, part number 204-559.

24

1. Fill the pressure tank as explained in the Pressure

Tank Instruction Manual 307-232.

2. Screw on the fill port cap (JI, or if the tank cover was removed, place the agitator and cover on the pressure tank and secure the cover with the c-clamp handles (K). See Fig 4.

WARNING

Overpressurizing the tank or accessories could cause a part to rupture. To reduce the risk of serious bodily injury, including fluid injection, splashing in the eyes or on the skin, and property damage, never exceed the maximum air and fluid working pressure of the lowest rated component in vour system.

3. Close the tank air regulator(s) by turning the knob(s) counterclockwise. Turn on the air supply.

4. To start the agitator, slowly open the needle valve

(20). Adjust the speed of the agitator, with the nee- dle valve, to about 40 to 60 RPM. Operate the agitator continuously while using the pressure tank.

~ DO NOT

CAUTION operate the agitator at a high speed for a long period of time. Excessive agitator speed can cause foaming of fluid (making the fluid unusable), vibration, and increased wear on parts. Always agitate the fluid only enough to maintain even mixing.

5. To stop the agitator, close the needle valve (20).

C-

Fig 3 Fig 4

307-792 3

Fig 5

Lubrication

Air Motor: To lubricate the air motor, place one drop of oil in the motor’s air inlet after about every 48 hours of operating time. The air motor may require more or less frequent lubrication, depending on the condition of the air supply.

Gear Reducer: After the first 100 hours or two weeks of operation, remove the drain plug, drain the oil, and thoroughly flush the housing with light flushing oil.

Remove the oil level plug, and refill with Grace oil (par-t number 204-559 to the proper level. Afterward, change the oil every six months or 2500 hours of operation

(whichever occurs first) under normal operating condi- tions. More frequent oil changes are needed under severe operating conditions or in atmospheres contain- ing excessive moisture or abrasives. Contact your Grace representative for recommendations.

Air Motor Service (See Fig 5)

If the air motor operation is erratic or sluggish, flush the motor as follows. Remove the muffler, and fill the cavity with kerosene. Wait 10 minutes, then operate the agitator slowly until all the kerosene is blown out.

If air motor operation is still sluggish, flush again.

DO NOT attempt to repair the air motor yourself. Con- tact an authorized Grace Service Center.

When replacing the air motor, place one-half of the coupling (3a) on the air motor shaft (L), flush with the end of the shaft. Tighten the coupling setscrew against the flat on the shaft.

Install the load cushion (MI on the gear reducer coupling half. Slide the clamp (2) onto the collar (4).

Align the two coupling halfs, and push the air motor hub into the collar (4) until it bottoms out, then back it out

0.015 in. Make sure the air motor inlet and outlet face up*

Apply Loctite@’ No. 222 to the two clamp setscrews

(32). Align the setscrews to one side of the slots on the collar (41, and tighten them.

Apply PTFE tape to the inlet (20) and outlet KZ?) fit- tings, and install them in the air motor.

4 307-792

Gear Reducer Service (See Fig 6)

DO NOT attempt to repair the gear reducer (51 yourself.

Contact an authorized Grace Service Center.

When replacing the gear reducer, remove the capscrews

(33) from the bottom of the old gear reducer. Remove the top coupling half (19a) from the old gear reducer, and install the coupling half on the new gear reducer.

Apply Loctite@ No. 271 to the four capscrews (33). In- stall them through the bracket (6) and into the gear reducer. Torque the screws to 220 in-lb 125 N-m). Make sure the three hole pattern on the bottom of the bracket

(6) is orientated as shown in Fig 6. Set the coupling as instructed under Setting the Output Shaft Coupling. r

CAUTION

DO NOT use the four screws supplied with the new gear reducer to secure it; those screws will not properly secure the gear reducer. Use the capscrews (33) which were removed from the old gear reducer. Be careful not to spill any oil from the gear reducer.

Setting the Output Shaft Coupling (See Fig 61

With the agitator shaft (14) pushed up against the washer (15a), secure the lower portion of the coupling half (19b) to the shaft by tightening the coupling setscrew against the flat on the shaft. Leave about a

0.015 in. gapbetweenthecoupling halfandwasher (15b).

Secure the upper coupling half (19a) to the gear reducer shaft by tightening the coupling setscrew into the keyway. Leave about a 0.015 in. gap between each of the coupling halfs /19a, 19b) and the load cushion (N).

Replacing the Agitator Shaft (See Fig 6)

Remove the setscrew from the lower coupling (19b).

Pull out the agitator shaft (14) and install the new shaft.

Set the coupling as instructed above.

Replacing the Coupling (See Fig 6)

Remove the three capscrews (181 from the mounting bracket (6). Pull the two coupling halfs (19a, 19b) out through the bottom of the mounting bracket (6).

Install the new coupling halfs in the mounting bracket.

Screw the three capscrews (18) back into the mounting bracket.

Replacing the Shaft Seals (See Fig 6)

Remove the setscrew from the lower coupling half

(19b). Pull out the agitator shaft (14).

Remove the three capscrews (18) from the mounting bracket (6). Remove the shaft housing (9). Remove the seals (9a, 9b) from the shaft housing, and install the new seals.

Reinstall the shaft housing and shaft.

Fig 6

19b.---

G n n

LN

307-792 5

6 307-792

24

20e

3 e

AIR CONSUMPTION CHART

PARTS LIST

REF PART

NO. NO.

DESCRIPTION QTY

13

14

15

;;

18

2

20a

20b

2oc sit

SY

22

;: s:

32

33

PTFE

103-553

104431

103-927

21 O-576

171-970

220463

108544

181-746

181-747

181-748

104-373

162-425

181849

100828

220-416

181848

170-751

181-794

181-749

106718

108-462

210580

102598

166-529

166-532

184-698

156-969

101-118

105-509

MOTOR, air

CLAMP

COUPLING, flexible

COLLAR, mounting

Includes items 4a Et 4b

.SLEEVE, mounting, air motor

.PLATE, mounting

REDUCER, gear

BRACKET, mounting

LOCKWASHER, int. shkprf, no. 10

SPACER

HOUSING, shaft

Includes replaceable items 9a Et 9b

. SEAL, shaft

.SEAL, shaft

CLAMP, hose

SUPPORT, shaft

Includes replaceable item 1 la

.BEARING, PTFE

PADDLE, agitator

SCREW, set, slot hd, 1/4-20x 0.5

SHAFT, 15”, 5 gal size

SHAFT, 20.75”, 10 gal size

SHAFT, 31”, 15 gal size

WASHER thrust; l/2’ ID x 1” OD

NUT, jam, hex; l-l/2”-12

GASKET, cork w/buns-N

SCREW, cap, socket head;

10-32x 0.5

COUPLING, flexible

NEEDLE VALVE ASSY.

Includes items 20a to 2Of

.NEEDLE, valve

.NUT, packing

.KNOB, packing

.O-RING; buna-N

.BODY, valve

.WASHER, nylon

HOSE, coupled; 400 psi (28 bar) maximum working pressure

MUFFLER

BAFFLE, aaitator

SCREW; cap, socket head;

1/4-20x 1”

NUT, hex, regular; l/4-20

SCREW, cap; 5/16-18x 314

SCREW, set, sch; 10-24x 0.25

SCREW, cap, sch; 5/16-18x 0.875

Loctite@ is a registered trademark of the Loctite Corporation. ii

3

1

1

3

1

1

1

1

1

:

1

1

1

;

:

1

:

1

1

1

1

1

1

1 f

;

4

HOW TO ORDER REPLACEMENT PARTS

1. To be sure you receive the correct replacement parts, kit or accessories, always give all of the information requested in the chart below.

2. Check the parts list to identify the correct part number; do not use the ref. no. when ordering.

3. Order all parts from your nearest Grace distributor.

6 digit

PART

307-792 7

SERVICE INFORMATION

Changed quantity of item 18, part no. 102-598-screw, from 1 to 3.

THE GRACO WARRANTY AND DISCLAIMERS

Grace warrants all equipment manufactured by it and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Grace distributor to the original purchaser for use. As purchaser’s sole remedy for breach of this warranty, Grace will, for a period of twelve months from the date of sale, repair or replace any part of the equipment proven defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Grace’s written recommendations.

This warranty does not cover, and Grace shall not be liable for., any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, neglrgence, accident, tampering, or substitution of non-Grace component parts. Nor shall Grace be liable for malfunction, damage or wear caused by the incompatibility with Grace equipment of structures, accessories, equip- ment or materials not supplied by Grace, or the improper design, manufacture, installation, operation or maintenance of structures, ac- cessories, equipment or materials not supplied by Grace.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective for examination by Grace to verify the claimed defect. If the claimed defect is verified, Grace will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the the costs of parts, labor and transportation.

DISCLAIMERS AND LIMITATIONS

THE TERMS OF THIS WARRANTY CONSTITUTE PURCHASER’S SOLE AND EXCLUSIVE REMEDY AND ARE IN LIEU OF ANY OTHER

WARRANTIES (EXPRESS OR IMPLIED), INCLUDING WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PAR-

TICULAR PURPOSE, AND OF ANY NON-CONTRACTUAL LIABILITIES, INCLUDING PRODUCT LIABILITIES, BASED ON NEGLIGENCE OR

CLUDED AND DENIED. IN NO CASE SHALL GRACO’S LIABILITY EXCEED THE AMOUNT OF THE PURCHASE PRICE. ANY ACTION FOR

BREACH OF WARRANTY MUST BE BROUGHT WITHIN TWO (2) YEARS OF THE DATE OF SALE.

EQUIPMENT NOT COVERED BY GRACO WARRANTY

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PAR-

TURED BY GRACO. These items sold, but not manufactured by Grace (such as electric motor, switches, hose, etc.), are subject to the warran- tv, if any, of their manufacturer. Grace will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

Subsidiary

Dallas, Detroit, Los Angeles, West Caldwell (N.J.)

Japan

GRACO INC. P. 0. Box 1441 MINNEAPOLIS.

PRINTED IN U.S.A. 307-792 12-86

MN 5544~1444.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement