Graco 307730D PT2000 Pressure Roller System Owner's Manual

Add to my manuals
24 Pages

advertisement

Graco 307730D PT2000 Pressure Roller System Owner's Manual | Manualzz

See The Painter’s Team@ line of products at your Grace distributor.

PT2501

‘14 gpm - Gas Electric

Airless Paint Sprayer (220-294 complete, and 220-296 bare)

’ PT2500 l/4 gpm - Electric Airless

Paint Sprayer (218-501 complete, and 218-796 bare)

PTlOOO Electric Airless Paint

Sprayer Kit (218-772)

PTArrow Striper (220-295)

PTllOO Cordless, Rechargeable

Caulking Gun (218-952)

PT2000 Professional Pressure

Roller System (218-938)

Airless Gun Pressure Roller

Accessory (218-625)

PT2040 Gas Pressure Washer

(800-164)

PT1535 Gas Pressure Washer

(800-165)

306

307-730

Rev D

SUPERSEDES C

PT2000@ Pressure Roller System patent

250 psi (17.5 bar) MAXIMUM WORKING PRESSURE

Model 218-938, Series B

with 18-36 in. Extension and l/2 in. nap Roller Cover

Model 220-345. Series B

with 18-36 in. Extension and l/2 in. nap Roller Cover and CSA certified

TABLE OF CONTENTS

Terms ..............................................................

Warnings .........................................................

Setup.. ............................................................

Startup ............................................................

Operation .........................................................

Maintenance

Flushing.. ......................................................

1

.2

PT2000 Pressure Roller System Description .............. .5

.6

.7

.7

.8

Installing & Removing a Roller Cover .................... .

Cleaning the Roller Diffuser.. .............................

Troubleshooting Chart.. .....................................

.Q

.10

Repair

Roller Valve.. ................................................

Fuse.. ..........................................................

ON/OFF Switch.. ..........................................

Rectifier.. .....................................................

Power Supply Cord.. ......................................

Pressure Switch ...........................................

Outlet Valve .................................................

Inlet Valve.. ..................................................

Diaphragm.. .................................................

Suction Tube.. ..............................................

Priming Valve & Tube .....................................

.I4

.I4

.I4

Motor, Connecting Rod & Bearing.. ................... ,I5

Parts Drawing & Lists.. ......................................

Accessories .....................................................

Technical Data.. ...............................................

.I1

12

.I2

12

.I2

..13

.13

-13

.16

,I9

,20

CAUTION

To avoid premature wear of the pressure switch, never use more than 25 ft (7.6 m) of l/4” ID outlet hose. When longer outlet hose is needed, use 3/8”

ID hose at a maximum of 100 ft (30 m) long. Never use l/4” ID and 3/8” ID hose together.

Do not use lacquer or lacquer thinner in the suc- tion and outlet hoses supplied with this system.

These fluids quickly destroy the hose material. Use the optional chemical-resistant hoses.

See ACCESSORIES section of the manual for ordering optional hoses.

TERMS

Be sure you read and understand each of these terms before reading the rest of the manual.

WARNING: Alerts user to avoid or correct conditions which could cause bodily injury.

CAUTION: Alerts user to avoid or correct conditions which could cause damage to or destruction of the equipment.

NOTE: Gives additional explanation of a procedure or helpful hints.

WARNING

Hazard of Using Fluids Containing Halogenated Hydrocarbons

Never use III, 1 -trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents in this equipment. Such use could result in a serious chemical reaction, with the possibility of explo- sion, which could cause death, serious bodily injury and/or substantial property damage.

Consult your material suppliers to ensure that the fluids being used are compatible with aluminum and zinc parts.

307-730 1

WARNING

Be sure all operators of this equipment read, understand, and follow the warnings and instructions in this manual!

GENERAL SAFETY:~~~~~ii.!~.i~~~~rs~,i.,;~.;;j,~;.r;-~~:,, ;> ,:

Use extreme care not to splash paint, contaminated flushing water or solvent into your eyes. Wear protec- tive eyewear.

Be sure the area in which you are working is well ven- tilated, to avoid a buildup of harmful paint fumes.

To reduce the risk of electric shock, do not expose the system to rain. Always store the system indoors. Do not operate the pump with the pump base cover removed. l:~.f.:’ s ;_ j,:r ‘.: :

Electrical grounding is essential to reduce the risk of an electric shock or other serious bodily injury from static sparking. Read and follow the grounding instructions on page 5 of this manual.

EXTENSION MSUSE HAZARD d<t:i ,i,i;, .e ’ : :.

THIS IS NOT AN AIRLESS GUN EXTENSION (for ex- ample, pole gun). Do not attempt to modify the exten- sion or roller frame, or to use parts which are not design- ed for use with this system. Use the extension only with the roller frame provided with this system.

Improper use of the extension, roller frame, hose or roller valve can result in component rupture or explosion and cause serious bodily injury.

EQ(J/pMENTMjS(jSE HAZAR&j~;~-;>: : ;::jiiriG;:;,:,‘,

This system is designed to be used at 250psi (77.5 bar)

MAXIMUM WORKING PRESSURE. the PT2000 System.

Use only com- ponents or accessories which are designed for use with

Any misuse of this equipment, such as modifying parts, using incompatible paint or solvent, or using worn or damaged parts, can cause the equipment to rupture and result in serious bodily injury, fire, explosion and proper- ty damage.

Never alter or modify any part of this equipment; doing so could cause it to overpressurize or malfunction.

Check all parts of the system regularly and repair or replace any worn or damaged parts immediately.

AVO/D POWER L/NES,~‘rj;il6,1i!i,j:;~,~;,~,~:~il:~1;j. ;.:.

Avoid contacting any power lines with the extension.

Contact with power lines could cause extremely serious bodily injury, including burns or electrocution.

WARNING

Never use 1 ,1 ,I -trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents in this equipment. Such use could result in a serious chemical reaction, with the possibility of explo- sion, which could cause death, serious bodily injury and/or substantial property damage.

Consult your fluid suppliers to ensure that the fluids being used are compatible with aluminum and zinc parts.

2

307-730

A VERTISSEMENT

Assurez-vous que tous les utilisateurs de cet dquipement lisent, compren- nent et observent les avertissements et les instructions de ce manuel!

SECURITE GENERAL yeux.

;

Faites extrgmement attention de ne pas dclabousser de peinture, d’eau de rincage sale ni de solvant dans les

Portez des lunettes de protection.

Assurez-vous que I’endroit ou vous travaillez est bien a&e afin d’bviter I’accumulation des vapeurs toxiques de peinture.

Pour reduire le risque de decharge blectrique, n’exposez pas /e systdme ri la pluie. Rangez toujours le systeme a

I’interieur.

M/SE A LA TERRE

II est essentiel d’effectuer la mise 8 la terre pour reduire le risque de decharge dlectrique et de blessures serieuses resultant des dtincelles d’electricite statique.

Lisez et observez les instructions de mise a la terre, B la page 5 de ce manuel.

CECI N’EST UNE RALLONGE DE PISTOLET SAN AIR

(par exemple, pistolet 8 tige). N’essayez pas de modifier la rallonge ni la monture du rouleau; n’essayez pas non plus d’utiliser des pieces qui ne sont pas concues pour aller avec ce systeme. N’utilisez la rallonge qu’avec la monture de rouleau fournie avec le systeme.

L’utilisation incorrecte de la rallonge, de la monture de rouleau, du tuyau ou du robinet du rouleau peut en- trainer la rupture des pieces ou une explosion et causer des blessures serieuses.

Ce systeme est concu pour dtre utilise a une PRESSION

MAXIMUM DE FONCTIONNEMENT de 17.5 bars

(250 psi). N’utilisez que des pieces ou accessoires qui sont concus pour &re utilises avec le systeme PT2000.

L’utilisation incorrecte de cet equipement, la modifica- tion des pieces, I’utilisation de peinture ou de solvant in- compatibles, I’utilisation de pieces u&es ou abTmees peuvent entrainer la rupture de I’equipement et causer des blessures graves, un incendie, une explosion et des degdts materiels.

Ne changez et ne modifiez jamais aucune piece de cet equipment; ceci pourrait entrainer une surpression et un mauvais fonctionnement.

Vdrifiez regulierement immediatement.

toutes

les pieces du systeme et reparez ou remplacez les pieces u&es ou ablmees

EVITEZ LES LIGNES ELECTRIQUES

Evitez tout contact avec les lignes electriques! Ceci pourrait causer des blessures t&s graves, y compris des brulures ou l’electrocution.

307-730 3

AD VERTENCIA

Asegurarse de que todos 10s operadores de este equip0 lean, entiendan y respeten las precauciones e instrucciones indicadas en este manual.

SEG(JRjDAD EN GENERALt;jgs;:r,; :;r:ir, y:;“:; . ’

Tener extremo cuidado de no salpicarse 10s ojos con pin- tura, agua de enjuague contaminada o solvente. Usar gafas protectoras. pEL/GRO POR MAL US0 DEL EQU/pO ~,~%$2@‘$@~

Este sistema esta disefiaao para una PRESION DE

I

TRABAJO MAXIMA de 17.5 barks (250 lbs/putg2/.

Usar componentes o accesorios disefiados para usarse con el sistema PT2000.

Asegurarse de que el lugar de trabajo tenga buena ven- tilicaion, para evitar la acumulacion de vapores de pin- tura nocivos.

Para reducir el riesgo de sufrir un choque electrico, no dejar este sistema expuesto a la lluvia. Siempre guar- darlo bajo techo.

El uso indebido de este equipo, tal coma modification de las piezas, uso de pintura o solvente incompatible, o de piezas dai’iadas o desgastadas, podria causar la rotura del equip0 y terminar en graves lesiones per- sonales, incendio, explosion y dafios a la propiedad.

.4i; $(:;gb: ‘; ;?.

La puesta a tierra es esencial para reducir el riesgo de sufrir un choque electrico u otras lesiones corporales graves debido a chispas estaticas. Leer y seguir las in- strucciones dadas en la pagina 5 de este manual.

Nunca alterar o modificar ninguna pieza del equipo; el hacerlo podria causar sobrepresion o malfunciona- miento.

Revisar con regularidad todas las piezas del sistema y reparar o sustituir de inmediato las que esten dafiadas o desgastadas.

PELIGRO POR MAL US0 DE LA EXTENSION r.v

ESTA NO ES UNA EXTENSION DE PISTOLA SIN AIRE

(par ejemplo, pistola con paste). No intentar modificar la extension o el portarradillo, o usar piezas que no hayan sido disefiadas para usarse en este sistema. Usar la ex- tension solamente con el portarrodillo provisto con este sistema.

ELECTRICOS @gggg&&

iProcurar no tocar ningun cable electrico! De llegar a suceder esto se podrian sufrir lesiones corporales sumamente graves, incluso quemaduras o elec- trocucion.

El uso indebido de la extension, portarrodillo, manguera o gatillo del rodillo podria romper o hater explotar el componente y causar graves lesiones corporales.

4 307-730

PT2000

PRESSURE ROLLER SYSTEM DESCRIPTION

SUCTION TUBE

PRIMINGTUBE

INLET VALVE

POWER SUPPLY CORD

PAINT STRAINER

25 ft (7.6 m) HOSE

18 to 36 in. (460 to 920 mm)

TELESCOPING EXTENSION

Motor

The motor drives the connecting rod which moves the diaphragm.

Pressure Switch

The pressure switch at the pump outlet turns the motor on and off to control paint pressure.

Diaphragm

The diaphragm is the heart of the pump. Driven by the connecting rod and motor, the movement of the diaphragm draws paint from the suction tube and through to the outlet valve.

Priming Valve

The priming valve assists in priming the pump during startup. Turning the priming valve counterclockwise causes the paint to drain directly back into the pail through the priming tube. Turning the knob clockwise causes the paint to flow through the fluid outlet valve and to the hose, roller valve and extension.

Outlet Valve

The outlet valve has a ball check which prevents paint from flowing backwards into the pump. This helps keep an even supply of paint to the roller each time you trig- ger the roller valve.

Inlet Valve

As the diaphragm draws paint from the suction tube, the paint passes through the inlet valve which opens to allow paint into the pump.

Outlet Hose

The hose has swivel-type couplings for easy assembly.

A larger diameter outlet hose and chemical-resistant outlet and suction hoses are available. See AC-

CESSORIES on page 19.

Roller Valve

The roller valve controls paint flow to the roller by trig- gering it on and off.

Pressure Roller

The pressure roller has a telescoping extension and a roller cover for use on smooth surfaces. Longer exten- sions and different types of roller covers are available.

See the ACCESSORIES on page 19.

307-730 5

SUCTION TUBE

PRIMING TUBE

INLET VALVE

MOTOR

POWER SUPPLY CORD

TIGHTEN SNUGLY

WITH LIGHT WRENCH

PAINT STRAINER

USE TWO WRENCHES

TO TIGHTEN

25 ft (7.6 m) HOSE

MUSTS

VALVE INLET USE TWO I WRENCHES

TO TIGHl -EN

I18 to 36 in. 1460 to 920 mm)

3/B” NAP

ROLLER

COVER

1. Remove all parts from the boxes and assemble them as shown in Fig 1, following any special notes on the drawing.

2. Prepare the paint according to the manufacturer’s recommendations. Remove any skin that may have formed on the top of the paint. If necessary, thin the paint.

WARNING

Never remove the third (grounding) pin of the power supply cord plug. Be sure the outlet is pro- perly grounded. In the event of an electrical short circuit, grounding reduces the risk of an electric shock by providing an escape wire for the electric current.

Inspect the power supply cord and extension cord before each use. Be sure they are in good condi- tion and have undamaged three-pin plugs. Replace immediately if either cord shows signs of wear or damage.

3. Plug the power supply cord into a properly ground- ed, 120 V electrical outlet. See Fig 2. Do not use an adapter. All extension cords must have three wires.

Use the chart at the right for selecting the ap- propriate wire gauge for the extension cord.

4. Loosen the locknut on the telescoping extension and adjust the extension to the desired length.

Firmly tighten the locknut.

6

307-730

COVER OF GROUNDED

OUTLET BOX

HAND TIGHTEN ONLY

ROLLER COVER

GROUNDING

Fig 2

L

Extension Cord Chart feet

Cord Length

(meters1

Extension Cord

Wire Gauge l-100

100-200

200-300 over 300

(l-30)

W-61 1

(61-92)

(over 92)

18

16

14

12

.

WARNING

To reduce the risk of serious bodily injury, including injury from moving parts or electric shock, always follow this procedure whenever you shut off the system, when checking or servicing any part of the system, and whenever you stop painting.

1. Turn the ON/OFF switch to OFF.

2. Unplug the power supply cord.

3. Trigger the roller valve to relieve pressure.

If you suspect that pressure is not fully relieved after following the steps above, open the priming valve 2 turns-counterclockwise.

I. Place the suction tube in the pail of paint.

.

1

!. Plug in the sprayer.

3. Open the priming valve 2 turns counterclockwise.

4. Turn the ON/OFF switch ON.

5. You can see the paint being drawn into the suction tube (if the tube is clean). As soon as you see paint flow through the priming tube, close the priming valve. This usually takes less than 30 seconds.

CAUTION

Failure to completely close the priming valve after the system is primed will cause the valve to erode, greatly shortening the valve life.

NOTE:

If your system is hard to prime, first try to force feed the suction tube. Hold the suction tube in a vertical position and pour paint into it. Turn on the system. If the system does not prime within one minute, shut it off. Heavy viscosity paint may need to be thinned. Be sure to follow the paint manufacturer’s recommendations on thinning.

6. Trigger the roller valve to prime the outlet hose and extension. Once primed, the motor will run when there is paint demand, but appears to shut itself off when there is no paint demand.

NOTE:

An occasional start and stop of the motor when the roller valve is off is normal.

To reduce the risk of electric shock, do not expose system. Always store the system indoors.

1. With the system fully primed, trigger the roller valve briefly until paint comes to the roller.

2. Experiment with triggering and rolling the paint until you determine just how often you need to trigger the roller valve to keep an even flow of paint to the roller.

3. To adjust the extension tube length, loosen the locknut and extend or retract the tube. If retracting, some paint in the tube will be pushed out to the roller. Roll this excess paint onto the wall, or com- pletely retract the tube, drain the excess paint into a pail, then adjust the tube length. Tighten the locknut securely.

4. Whenever you stop painting, turn the ON/OFF switch to OFF and trigger the roller valve. Then elevate the roller end of the tube to prevent paint from draining out the roller end.

5. Flush the system thoroughly and immediately after each use to keep it in good working order. See page 8.

307-730 7

CAUTION

Thorough flushing and proper maintenance are essential to keep your system working properly!

Improper flushing or maintenance may prevent the system from working the next time you need it, and may result in costly damage to the system.

AL WAYS flush your system thoroughly and im- mediately after each use.

AL WAYS fully extend the telescoping extension when flushing to clean it thoroughly.

AL WAYS drain all water out of the roller valve and extension and leave the system filled with mineral spirits to prevent corrosion.

NOTE:

A Power Flush Adapter, Grace P.N. 220-231 is available. This accessory is placed at the pump inlet and uses a standard city water supply to aid in flushing. See AC-

CESSORIES, page 19, to order. Instructions on how to use it are included with the adapter. bETAIL A

Flushing (Latex Paint Only)

1. Turn the ON/OFF switch to OFF.

2. Fully extend the telescoping extension.

3. Trigger the roller valve and roll out the excess paint from the roller onto a wall or newspaper. Remove the roller cover and diffuser, and soak in a pail of warm soapy water.

4. Place the suction tube in the pail of warm soapy water.

Hold the roller frame over the paint pa,;! turn on the system and trigger the roller valve to drain and save the paint in the hoses. Release the trigger and shut the pump off just as soon as all paint is drained, to avoid contaminating the paint with the flushing water.

5. Now hold the roller frame over the flushing pail.

Turn on the pump and trigger the roller valve. Cir- culate the solution for three to five minutes (five to ten minutes if it is cold). Pump the extension in and out a few times to clean it, then leave it extended.

Then open the priming valve for a few seconds to clean the priming tube. Close the valve.

6. Raise the suction tube above the water and run the pump for a few seconds to drain the flushing solu- tion. Shut off the pump.

7. Wash off all external parts of the hoses, extension, roller frame, roller valve and pump.

8. Using clean, clear water, flush again, changing water as often as necessary, until the system is thoroughly cleaned.

9. Finally, flush the system with clean mineral spirits for just a few seconds. Open the priming valve and turn off the pump. Some mineral spirits must be left in the system to prevent corrosion. Retract the ex- tension.

Fig 3

8

307-730

Never leave water or water-based paint (latex) in

10. Clean the roller cover thoroughly by rinsing it inside and out. Clean the diffuser as explained on pge 5.

11. Oil the needle in the roller valve and trigger the valve a few times to distribute the oil. See Detail A, Fig 3.

Fl;+pg (Oil-based Paint Only)

: Follow the instructions above, except use mineral spirits. Do not heat the mineral spirits.

Installing and Removing a Roller Cover (See Fig 4)

1. To install a cover hold the diffuser and unscrew the retainer nut. Slide the cover over the diffuser assembly and reinstall the nut. Be careful not to overtighten the nut.

2. To remove a cover, hold the cover and unscrew the retainer nut. Slide the cover and diffuser assembly off the roller frame, and press on the end of the dif- fuser assembly to separate it from the cover. r

NUT

Cleaning the Roller Diffuser (See Fig 5)

1. For water base paint (latex), vigorously shake the diffuser in a pail of hot soapy water to remove un- dried paint. For oil-base paint, use mineral spirits.

Use a soft brass bristle brush to remove dried paint.

2. To clear an obstruction in the frame, or for more thorough cleaning, remove the screw. Be sure to reinstall it after cleaning.

3. Disassemble if fur&her cleaning is needed. a. b.

C.

Remove the two screws. Pull off the outside end cap. Disassemble all parts and clean thoroughly in water or mineral spirits.

Install the inside end cap on the frame. Lightly grease the o-ring with petroleum jelly. Slide the diffusers onto the roller frame. Twist and press the last diffuser to snap the pieces together.

Install the outside end cap and the two screws.

Holding the inside end cap, press on the screws and rotate the diffusers to seat the screws.

Tighten the screws evenly into the inside end cap. Be sure there is no binding and that the dif- fusers move freely.

INSIDE END CAP SCREW

LIGHTLY WITH

PETROLEUM JELLY

FRAME

-iI

Fig 5

OUTSIDE END

CAP

Fig 4

307-730

9

WARNING

To reduce the risk of serious bodily injury, including injury from moving parts or electric shock, always follow this procedure whenever you shut off the system, when checking or servicing any part of the system, and whenever you stop painting.

1. Turn the ON/OFF switch to OFF.

2. Unplug the power supply cord.

3. Trigger the roller valve to relieve pressure.

If you suspect that pressure is not fully relieved after following the steps above, open the priming valve two turns counterclockwise.

TROUBLESHOOTING CHART

. ..VYLW...

FM

Pump will not prime, or takes long time to prime

’ CblJSF

Clogged suction tube strainer

Paint too thick

Outlet valve spring worn or damaged

Inlet valve stuck or damaged

1 SOLUTION

Clean.

Thin; try pouring paint into suction tube; use 3/8” ID hose if necessary.

Pour paint into suction tube and tn/ to prime system. If it doesn’t prime in one minute, replace the outlet spring. See Outlet Valve, page 13.

Depress valve gently and pour in about 1 teaspoon mineral spirits.

Try to prime pump. Replace valve if necessary. See Inlet Valve, page 13.

DEPRESS LIGHTLY.

POUR IN 1 TEASPOON

MINERAL SPIRITS.

Loose inlet hose nut Tighten.

Pump will not start Power cord unplugged

ON/OFF switch turned off

Damaged motor

Fuse burned out

Plug in.

Turn on.

Replace. See page 15.

Replace. See page 12. If it burns out again soon, return the system to an authorized repair agency for repair.

Low or no paint flow Clogged roller cover, diffuser, roller frame, roller valve or hose g;zsrre than 25 ft (7.6 ml of l/4”

Loose inlet hose nut

Worn or damaged priming valve

Priming valve is open

Paint too thick

Clean thoroughly after each use.

See Flushing on page 8.

Use up to 100 ft (36 m) of 3/8” ID hose. See CAUTION, page 1.

Tighten.

Replace. See page 14.

Close.

Thin according to manufacturer’s recommendations.

Replace. See page 13.

Replace. See page 13.

Damaged pressure switch

Worn inlet and/or outlet valve

Pump runs after is released roller valve trigger Worn or damaged pressure switch

Worn or damaged inlet valve

Worn or damaged outlet valve

Worn or damaged priming valve

Worn roller valve packings or needle

NOTE:

If you are not able to determine the cause of the problem, or the problem and solution chart, return the system to an authorized service agency for repair.

Replace. See page 13.

Replace. See page 13.

Replace. See page 13.

Replace. See page 14.

Repair. See page 11. is not discussed in this

10 307-730

Roller Valve

WARNING

Always follow the Pressure Relief Procedure

Warning on page 10 before attempting any repair.

NOTE: Order reoair kit no. 218960 to repair this roller valve.

1. Tap out the pin (A) from the trigger (B) and slide the trigger off of the valve (N). See Fig 6.

2. Remove the cap (Cl. Use a l/2 in. socket wrench to screw the fluid housing (D) out of the valve.

Remove the o-ring (J). See Fig 6.

Pull the needle (K) out with needle nose pliers. 3.

4.

5.

Tap the seat (G) out of the valve (N). See Fig 6.

Remove the ball (F) and spring (El from the valve handle. See Fig 6.

6.

7.

8.

9.

IO.

Turn the nylon screw (L) into the packing (HI. Insert the needle (K) through the bottom of the housing

(D) and push the packing out the top of the fluid housing. See Fig 7.

Clean all parts thoroughly. Use a cotton-tipped swab or pipe cleaner to clean small orifices.

Grease the needle (K) and packing (HI. Insert the tapered end of the needle into the back (flat1 side of the packing. See Fig 8.

Guide the tapered end of the needle into the assembly tool (MI and press the lips of the packing over the end of the tool. See Fig 8.

Grease the free end of the needle (K). Guide the tool

(Ml into the fluid housing (D) until the needle pro- trudes through the bottom of the housing. Lightly tap the tool end until you “hear” the packing bot- tom in the housing. Remove the tool with pliers.

See Fig 8.

11.

12.

Grease the seat (G) and place it on the fluid housing so the seat which is formed on the inside diameter faces out. See Fig 9.

Install the spring (E) in the spring cavity of the valve handle (N), then install the ball (F) so it is centered on the spring. See Fig 6.

13.

14.

15.

16.

Place the o-ring (J) around the fluid housing.

Pushing lightly with your fingers, start the threads of the housing into the valve handle. Torque the housing to 15-20 in-lb (1.7-2.2 N-m). See Fig 9.

Push on the needle until you feel some resistance.

Grease the cap (C) and place it on the end of the needle. See Fig 9.

Slide the trigger (B) into place. Install the pin (A) in the trigger. See Fig 6.

Fig 6

Fig 7

LIPS FACE OUT fl

OF HOUSING (D) kd

Fig 8

\-II LK

SEAT MUST

FACE BALL r TAPERED END

\-H LM

15-20 in-lb

(1.7-2.2 N-m)

Fig 9

307-730 11

WARNING

These repair procedures should be performed only by qualified repair personnel with an electrical back- ground, using the proper tools. Failure to do the pro- cedures correctly can result in electric shock, or other serious injury and damage to the pump.

WARNING

Pressure Relief Procedure

To reduce the risk of serious bodily injury, including injury from moving parts or electric shock, always follow this procedure whenever you shut off the system, when checking or servicing any part of the system, and whenever you stop painting.

1. Turn the ON/OFF switch to OFF.

2. Unplug the power supply cord.

3. Trigger the roller valve to relieve pressure, if you suspect that pressure is not fully relieved after following the steps above, open the priming valve two turns counterclockwise.

NOTE:

For all electrical repair, follow the Pressure

Relief Procedure Warning above, and then remove the pump base cover (421, screws

(33) and bumpers (43). Reinstall these parts, making sure all wires are tucked in neatly, before checking or operating the system.

Fuse (See Fig 10)

1. Pull the old fuse out of the fuse holder (65) and in- stall a new fuse (67). Be sure you install only a 3AG fuse, rated at 2 amps for Model 2 78-938 and rated at

I- 7 14 amps for Model 220-345.

Rectifier (See Fig 11)

1. Disconnect the four leads from the rectifier.

2. Remove the screw (33b) and rectifier (39).

3. Install a new rectifier so the positive terminal ( + ) is closest to the fuse holder (65) and then install the screw (33b).

4. Connect the power supply cord’s white lead to an unmarked terminal, and the pressure switch lead to the other unmarked terminal. Connect the black motor lead to the negative ( - 1 terminal, and the red motor lead to the positive ( + 1 terminal.

ON/OFF Switch

1. Disconnect the two leads from the ON/OFF switch terminals. See Fig 11.

2. Remove the boot (36) and pull the switch (34) out of the base. Remove the ground wire WI). See Fig 10.

3. Remove the top nut (34a) from the new switch.

Place the connector of the ground wire 034) on the switch and reinstall the nut. Install the new switch, aligning the tab in the base with the slot in the switch. See Fig 10. Then install the boot.

4. Connect a pressure switch lead to the power-out terminal, and a jumper wire lead to the power-in ter- minal.

Power Supply Cord (See Fig 10 & 11)

1. Disconnect the white lead from the rectifier (39) and the black lead from the fuse holder (65) and the green lead from the grounding screw (82).

2. From the inside of the base, use a screwdriver to push the strain relief bushing (38) out of the base.

Remove the bushing and power supply cord.

3. Slide the strain relief bushing over the new power supply cord press the bushing together, and press the bushing into the base.

12

307-736

Fig 10

GREEN WIRE 1

Fig 11

/-=

133

SWITCH (21

LEADS I7

\25 h

‘IRE

4. Connect the green ground wire to the grounding screw (82) and secure it with a washer (81) and nut

(80). Connect the black lead to the fuse holder (65) and the white lead to an unmarked terminal on the rectifier (39).

WARNING

To maintain grounding continuity in your system, and reduce the risk of electric shock, be sure the green ground wire of the power supply cord is properly connected to the screw (33) and the ground wire (84) is properly connected between the ON/OFF switch and the screw (82) as in- structed in Step 4, above. Also be sure the screw

(25) is tightly screwed into the base. See Fig 10 and 11.

Pressure Switch (See Fin 11, 12 & 13)

1. Disconnect the pres&re switch leads from the

ON/OFF switch and from the rectifier.

2.

3.

4.

5.

6.

Remove the screws (24) and front cover (23). See

Fig 13.

Unscrew the retainer (14) and remove the pressure switch (121 and o-ring (13).

Grease and install a new o-ring (13) in the pump housing (91.

Slide the retainer (141 over the pressure switch and screw the retainer into the pump housing. Torque the retainer to 55-65 in-lb (6.2-7.4 N-m).

Guide the pressure switch leads through the base.

Connect a> lead to the power-out side of the

ON/OFF switch (34) and a lead to an unmarked ter- minal on the rectifier (39).

LUBRICATE

7. Reinstall the front cover plate.

I.wlt.hcAuT’oN’I

Fig 12

Outlet Valve (See Fig 12)

1. Remove the outlet hose (64). Unscrew the outlet fit- ting (2a) and remove the gasket (2b) and spring (2~).

2. Tip the pump forward to remove the ball (2d).

3. Use a l/4 in. square socket wrench extension to screw out the seat (2e).

4. Use a pointed tool, such as a dentist’s pick, to remove the seal (2f).

5. Thoroughly clean all parts and dry.

6. Tip the pump back. Install a new seal (2f) making sure it lays flat.

7. Install the seat (2e) and torque it to 120-146 in-lb

(13.5-16 N-m).

8. Drop in the ball, making very sure it stays there!

I---- ouT’oNl

TO,&, TO

470-490 in-lb

63-55 N.m)

9. Check the ball stop pin in the outlet fitting (2a) for wear or damage, and replace the fitting if necessary.

Place a new gasket (2b) around the fitting. The last coil on one end of the spring (2~) is turned in. Place this end on the ball stop pin. Screw the fitting into the pump housing, torquing to 286-366 in-lb

(32-34 N-m).

Inlet Valve (See Fig 13)

1. Unscrew the suction hose (44) from the inlet valve housing (1). Screw the inlet valve housing out of the pump housing (9).

2. Remove the inlet valve (3).

3. Grease the inlet valve (3) to hold it in place during assembly and then install it in the valve housing.

Screw the valve housing into the pump housing, torquing to 470-496 in-lb (53-55 Nam).

NOTE:

To torque the inlet valve, have someone firm- ly hold the pump housing (9).

Fig 13

TORQUE TO

280-300 in-lb

24

23

307-730

13

Diaphragm (See Fig 14)

CAUTION

Replace the diaphragm whenever you remove the pump housing (9) or after each 100 hours of use, whichever comes first. During use, small grooves are formed in the diaphragm which cannot be realigned properly. Reusing a diaphragm may cause leaking which will result in costly damage to the pump.

I. Remove the screws (151, and lockwashers (16). Tip the pump housing (9) back, being careful not to damage the wires. Remove the screws (24) and front cover plate (23).

2. Check the diaphragm guide (11) in the bottom of the pump housing (9) for signs of wear or damage, and replace it if necessary, When replacing the guide, clean the pump housing thoroughly, then press the new guide, flat side first, into the housing, using only your fingers. Be sure it is installed evenly.

3. Screw the diaphragm (17) out of the connecting rod assembly (18).

4. Using a soft brass or nylon bristle brush, clean the top of the connecting rod and housing. Taking care not to damage the diaphragm grooves, gently clean the bottom of the pump housing (9).

5. Check the rod, motor bearing and eccentric for any sign of paint. If there is any paint or damage, clean or replace the connecting rod assembly as explained on page 15.

6. Screw the new diaphragm (17) into the connecting rod just until it bottoms out. Then turn it 1 I4 to 1 I2 turn (6-8 in-lb [2.7-3.6 N.ml).

Never turn the diaphragm more than l/2 turn

~tc~~T~~: will prevent the diaohranm from wdrkina orooerlv.

7. Apply thread lubricant to the screws (15) and install them with the lockwashers in the pump housing.

Torque the screws a few inch-pounds (N-m) at a time, oppositely and evenly, to 85 in-lb (9.8 N-m).

8. Spin the motor shaft (D) to be sure it turns freely.

9. Reinstall the front cover (23) and screws (24).

Priming Valve 8 Tube (See Fig 15)

NOTE:

Each new priming valve kit includes a priming tube and fittings.

1 Unscrew the nut on the handle (E) of the priming valve (lOa), then unscrew the stem of the handle.

2. Screw the priming valve (lOa) out of the pump housing (9).

3. Wrap the threads of the priming valve with PTFE tape as shown in Fig 15, then screw it snugly into the pump housing. The valve handle should be parallel with the angled edge of the housing to avoid interference with the inlet or outlet valves,

4. Slide the nut (10d) and ferrule (10~) onto the tube

(K&j, then install the tube support (lob) in the end of the tube. Screw the nut onto the priming valve, which will seat the ferrule.

5. Screw the stem of the handle (El onto the priming valve until it bottoms, then back it out two turns.

Screw the

nut

hand tight onto the priming valve, then tighten the stem into the valve.

14 307-730

THREADS

TORQUE TO

85 in-lb

(9.6 N.m)

Fig 14

Fig 15

Suction Tube (See Fig 15)

1. Unscrew the nut (45) from the fluid inlet valve ing (1). Remove the hose clamp (47). Slit the suc- tion hose to free the nipple (46).

hous-

2. With the nipple (46) inserted through the nut (451, dampen the new hose (44) with warm water and press the hose over the nipple. Screw the nut onto the inlet valve housing, then press the hose further onto the nipple, leaving about a l/8 in. (3 mm) gap between the nut and hose end.

3. Install hose clamp (47) and tighten snugly.

4. Remove the filter housing (48) and strainer (49) from the old suction hose and install them on the new hose. Dampen the hose with warm wh.ar to ease assembly.

Connecting Rod and Bearing (See Fig 16)

1. Remove the screws (24) and front cover plate (23).

Remove the screws (15) and lockwashers 116) and tip the pump housing (9) out of the way. Unscrew the diaphragm (17) and discard.

Replace the diaphragm (17) whenever you remove the pump housing (9). During use, small grooves are formed in the diaphragm which cannot be cause leaking which will result in costly damage to

2. Remove the motor screws (20) and lockwashers

(21). Lift the motor (30) slightly. Holding the con- necting rod, pull the motor away from the housing

02).

3. Inspect the bearing (18b) in the connecting rod

(18a). If it looks worn or any rollers are broken, replace the bearing and rod assembly (18). Inspect the motor eccentric, and replace the motor if the ec- centric is worn.

4. Use your fingers to pack high-quality bearing grease rhoroughly in between the bearing rollers.

Thorough greasing tend the life of the bearing and the motor eccentric.

5. Using a soft brass or nylon bristle brush, clean the top of the connecting rod and housing. Taking care not to damage the diaphragm grooves, gently clean the bottom of the pump housing (9).

6. Install the connecting rod (18) in the connecting rod housing (22). Screw a new diaphragm (17) into the rod just until it bottoms. Turn the diaphragm l/4 to l/2 turn more (6-8 in-lb [2.7-3.6 N-ml). Do not turn more than l/2 turn, or the diaphragm will not func- tion properly.

7. Align the motor with the pins in the connecting rod housing (221, guiding the motor eccentric through the connecting rod bearing (18b). Spin the motor shaft to be sure it moves freely.

8. Loosely install the lockwashers (21) and screws (20) to hold the motor. Spin the motor shaft again. Now alternately tighten the screws with a 9/64 in. hex key wrench. Spin the motor shaft again.

CAUTION

Spinning the motor shaft while assembling the pump ensures that parts are properly aligned. If they are not, and you start the pump, serious damage could result to the motor, bearing, and connecting rod. If you feel binding or resistance, disassemble the parts, checking the spin often, un- til you determine the cause of the binding.

9. Position the pump housing (9) on the sprayer.

I

Lubricate the screws (15) and install them and the lockwashers (16) loosely. Torque the screws a few inch-pounds (N.m) at a time, oppositely and evenly, to 85 in-lb (9.8 N.m).

10. Reinstall the front cover plate (23) and screws (24).

THOROUGHLY

-33 -42

Fig 16

Motor (See Fig 16)

1. Remove the screws (24) and front cover plate (23).

2. Remove the screws (33), bumpers (43) and pump base cover (42). Disconnect the motor leads from the positive and negative rectifier terminals. See Fig

11, page 12.

3. Remove the motor screws (20) and lockwashers

(21). Lift the motor (30) slightly. Holding the con- necting rod, pull the motor away from the housing

(22).

4. Inspect the bearing (18b) in the connecting rod

(l&l. If it looks worn or any rollers are broken, replace the bearing and rod assembly (18) as in- structed to the left.

5. Use your fingers to pack high-quality bearing grease thoroughly in between the bearing rollers.

6. Feed the motor leads through the rubber grommet

(69). Align the motor with the pins in the connecting rod housing (221, guiding the motor eccentric through the connecting rod bearing (18b). Spin the motor shaft to be sure it moves freely.

7. Loosely install the lockwashers (21) and screws (20).

Spin the motor shaft again. Alternately tighten the screws with a 9/64 in. hex key wrench. Spin the motor shaft again. See the CAUTION in step 8 of

Connecting Rod and Bearing.

8. Connect the red motor lead to the positive ( + 1 ter- minal and the black motor lead to the negative ( - 1 terminal of the rectifier (39). Refer to Fig 11.

9. Reinstall the pump base cover (42) bumpers (43) and screws (33). Reinstall the front cover plate (23) and screws (24).

307-730

15

16

307-730

38

~IITAIL

17

A, page 17

Detail A

APPLY SEALANT

TO THREADS

Ref No. 66

Roller Frame

Includes items 5!5a-66s

9’

LUBRICATE

TORQUE TO

66-66 in-lb

(6.2-7.4 N.m) w&f -;2d .

2

120

(13 5-16 N*m

TORQUE TO

2 60-300 in-lb

(32-34 N.rn) I

55d

--II

SEE PARTS DETAIL ABOVE

PRESSURE ROLLER SYSTEM

Model 218-938, Series B

Includes items l-83

REF PART

NO. NO.

DESCRIPTION ii

10

::

::

15 zJ

26 z

:

E

2c

2d

2e

2f

29 loo-079

181-147

23 r

181-168

181839

30

--L

31

32

33

181-172

“218-977

218-978

160454

107521

101-956

218968

180455 l 21 8-976

181-146 l 21 8-973

181-152

218-974

108-195

181-209

108225

104-008 l 275-619

218981

108-237

106-236

102-313 loo-028

108-213

108-230

181-215

218-975

181~800

181-180

181-744

181-182

181840

108224

HOUSING, valve, inlet

OUTLET VALVE KIT

Includes items 2a-2f

. FITTING, outlet

.GASKET

.SPRING

.BALL

.HOUSING, seat, valve

.SEAL, washer

INLET VALVE KIT

HOUSING, pump

PRIMING VALVE KIT

GUIDE, diaphragm

SWITCH. oressure

O-RING ’ ’

RETAINER

CAPSCREW, socket head;

5/16-18x l-1/6” long

LOCKWASHER.

DIAPHRAGM sorina. 5/16”

’ -’

CONNECTING ROD Et BEARING

CAPSCREW, socket head:

No. 8-32 x 518”

LOCKWASHER, spring, 0.168”

HOUSING, corm rod; Always order two of Ref No. 27 when replacing housing

COVER, front

Model 2 18-938 onlv

COVER, front

Model 22K345 only

SCREW, math, filh, No. 8-32 x 1.75”

CAPSCREW, hex head;

114-20 x 1.75”

LOCKWASHER, l/4”

PIN, dowel internal, shakeproof;

SCREW, math, hex washer head; self tapping; l/4-14 x 1”

LABEL, designation, front

MOTOR, electric; includes Ref No. 71

Model 2 18-938 only

MOTOR, electric; includes Ref No. 71

Model 22@345 only

BASE, pump

Model 2 18-a only

BASE. oumo

Modei .&G&5 only

HANDLE

Model 218-938 onlv

HANDLE

Model 220-346 onlv

SCREW, thd forming, pnh;

No. 8x7/8”

ROLLER VALVE REPAIR KIT

Includes items A through H

218360

Individual parts not sold separately.

See page 11 for instructions.

,’ i’

,_,’

QTY

1

1

:

2

1

1 z

2

1

1

1

1

1

6

Model 220-345, Series A, CSA Certified

Includes items I-83

REF PART

NO. NO.

DESCRIPTION

34 z

:

3:

37

42

43 i25 z it

52

53

I

El

E

E

55s

59 ii7

62

63

64

65

67

68

69

70

;i

E

62

84

105-679

181-213

105-659

106-192

163-301

181-156

181-799

108-220

181231

181-159

181-166

108-231

181-163

181-164

178-342

181-219

181-786

181-214

218-935

218-934

108-186

275-644

218582

101983

167-703

107590

218-775

108-356

108-199

108223

181-218

181-184

181-787

103584

2204390

SWITCH, toggle

LABEL, designation, right hand

TOGGLE, boot

CORD, power supply

BUSHING. strain relief

RECTIFIER, bridge

WIRE, jumper (not shown)

TERMINAL, ground

COVER, base

Model 2 18-938 onlv

COVER, base

Model 220-345 onlv

.

’ BUMPER

TUBE, suction

NUT, coupling

NIPPLE, hose

CLAMP, hose

HOUSING, filter

FILTER

CLAMP, hose

LABEL, designation

Model 2 78-938 only

LABEL, designation

Model 220-345 only

LABEL, designation, left hand

FRAME, roller

Includes items 55a-55e

.DIFFUSER. roller

.O-RING, retainer

. NUT, retainer

.FRAME, roller

.SETSCREW

NIPPLE, pipe, reducing; 3/8 to

II4 npt

VALVE, roller

NIPPLE, 3/8 npt(m) to 3/8 npsmfm)

COVER, roller, l/2” nap

EXTENSION, adiustable, 18-36”

(0.45-0.9 m).long

HOSE, fluid, nitrile rubber: cold

3/8 npsmfm); 25’ (7.6 m)‘long

HOLDER, fuse

FUSE, electrical, BAWG, 2 amp

Model 2 78-938 only

FUSE, electrical, BAWG, 1.2 amp

Model 220-345 only

;zR;;,, ;k$ forming, pnh;

GROMMET, rubber

LABEL, warning

Model 218-938 onlv

LABEL, warning

Model 220-345 only

TERMINAL

SETSCREW. 5/16-18 x .625”

NUT, hex, mscr; No. 6-32 unc-2b

LOCKWASHER, No. 6

SCREW. math. bdah:

No. 6-32 unc-29 x -l j4”

WIRE, ground

*Recommended “tool box’ spare parts.

See Wow To Order Replacement Parts” on page 19.

QTY

1

1

:

5in!

1

1

:

1

1

1

1 i

1

:

1

1

1

1

1

1

1

:

1

1

:

1

:

1

1

1

2r

1

U

18

307-730

CAUTION

To avoid premature wear of the pressure switch, never use more than 25 ft (7.6 m) of l/4” ID outlet hose. When longer outlet hose is needed, use 318”

ID hose at a maximum of 100 ft (30 m) long. Never use l/4” ID and 318” ID hose together.

Do not use lacquer or lacquer thinner in the suc- tion and outlet hoses supplied with this system.

These fluids quickly destroy the hose material. Use the optional chemical-resistant hoses.

CHEMICAL-RESISTANT

HOSES

SUCTION B OUTLET

For use with lacquer and lacquer thinners.

205-142 Outlet Hose; Nylon; 3/8” ID; cpld 3/8 npsm(fbe); 25’ (7.6 m); 300psi 121 barl MAX-

IMUM WORKING PRESSURE

219-095 Suction Hose; Nylon

LARGER DIAMETER OUTLET HOSE

Use this hose when using more than 25 ft (7.6 m) of outlet hose. Not intended for use with lacquer or lacquer thinners.

220-609 Outlet Hose; 3/8” ID; cpld 3/8 npsmifbe); 50’

(15 m); 250 psi 117.5 bar) MAXIMUM WORK-

ING PRESSURE

NIPPLE 108-228

Needed to couple two lengths of hose 220-009.

3/8 npsmfmbe)

ADAPTER FITTING 220-265

5ooo psi (350 bar) MAXIMUM WORKING PRESSURE

Couples roller frame directly to roller valve.

3 in. ROLLER FRAME 8 DIFUSER 220-234

Same as 9 in. but shorter. Must order cover separately.

3 in. ROLLER COVER 108-462 l/2 in. (12 mm) nape, for semi-rough to smooth sur- faces.

9 in. ROLLER COVERS

107-590 l/2 in. (12 mm) nap, for semi-rough to smooth surfaces

107-591 3/4 in. (19 mm) nap, for semi-rough surfaces

107-592 l-1/4 in. (32 mm) nap, for rough surfaces

ADJUSTABLE EXTENSION TUBES

218-775 18-36 in. (0.45-0.9 m)

218-778 3-6 ft (0.9-1.8 m)

218-777 6-12 ft (1.8-3.7 m)

218-778 8-16 ft (2.4-4.8 m)

SPRAY WAND 220-236

4050 psi (260 psi) MAXIMUM WORKING PRESSURE

Creates soft spray when used with PT2000

TWO ACCESSORY ADAPTER 220-232

ICKX) psi 170 bar) MAXIMUM plicators simultaneously.

WORKING PRESSURE

Adapts pump outlet of PT2000 to use two accessory ap-

FLUSH ADAPTER 220-231

Allows you to use city water supply to quickly flush the

PT2000

HOW TO ORDER REPLACEMENT PARTS I:%:

Listed below by the assembly changed are OLD, NEW,

ADDED and DELETED parts.

1. To be sure you receive the correct replacement parts, kit or accessories, always give all of the information requested in the chart below.

ASSEMBLY PART

CHANGED STATUS

REF PART

NO. NO. NAME and 220-345 ADDED (1)

26 100-028 Lockwasher

33 108-224 Screw

SYSTEMS OLD

NEW

DELETED

ADDED

181-167 Terminal

41 183-301 Terminal

83 168-223 Washer

84 220-890 Wire

UANTITY CHANGE NOTE: Number in parentheses I the Status column indicates the quantity added.

I 2. Check the parts list to identify the correct part number; do not use the ref. no. when ordering.

3. Order all parts from your nearest Grace distributor.

6 digit

PART

NUMBER QTY PART DESCRIPTION

307-730

19

TECHNICAL DATA

Maximum Operating Pressure : 260 psi (17.5 bar)

Power Requirements : Model 218-938: 120VAC, 6OHz, 1 Phase, 1 .O amp

Model 220-345: 120 VAC. 6OHz, 1 Phase, 1 .O Amp

Pump Output : 1 gallon (3.8 liter) in 5 minutes

Power Supply Cord : No. 16 AWG, 3 wire, 6’ (1.7 m) long

Wetted Parts : Aluminum, Brass, Viton ? Delriny Polyurethane, Neoprene,

Tungsten Carbide, Stainless Steel, Nylon, Plated Steel, Buna-N,

Polyester, Polyvinyl Chloride

Weight : 13.5 lb (6.1 Kg)

Vito@ and PTFE

THE GRACO WARRANTY AND DISCLAIMERS

WARRANTY

Grace warrants all equipment manufactured by it and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Grace distributor to the original purchaser for use. As purchaser’s sole remedy for breach of this warranty, Grace will. for a period of twelve months from the date of sale, repair or replace any part of the equipment proven defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Grace’s written recommendations. abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Grace component parts. Nor shall Grace be liable for malfunction, damage or wear caused by the incompatibility with Grace equipment of structures, accessories, equip- ment or materials not supplied by Grace, or the improper design, manufacture, installation, operation or maintenance of structures, ac- cessories, equipment or materials not supplied by Grace.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective for examination by Grace to verify the claimed defect. If the claimed defect is verified, Grace will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the the costs of parts, labor and transportation.

DISCLAIMERS AND LIMITATIONS

THE TERMS OF THIS WARRANTY CONSTITUTE PURCHASER’S SOLE AND EXCLUSIVE REMEDY AND ARE IN LIEU OF ANY OTHER

WARRANTIES (EXPRESS OR IMPLIED). INCLUDING WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PAR-

TICULAR PURPOSE, AND OF ANY NONCONTRACTUAL LIABILITIES, INCLUDING PRODUCT LIABILITIES, BASED ON NEGLIGENCE OR

STRICT LIABILITY. EVERY FORM OF LIABILITY FOR DIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES OR LOSS IS EXPRESSLY EX-

BREACH OF WARRANTY MUST BE BROUGHT WITHIN TWO (2) YEARS OF THE DATE OF SALE.

EQUIPMENT NOT COVERED BY GRACO WARRANTY

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PAR-

TURED BY GRACO. These items sold, but not manufactured by Grace (such as electric motor, switches, hose, etc.), are subject to the warran- tv, if any, of their manufacturer. Grace will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

Subsidiaw

Factory and Affiliate

Branches:Atlanta,

Companies:Canada;

Dallas, Detroit, Los Angeles, West Caldwell (N.J.J

England: Switzerland; France; Germany; Hong Kong; Japan

GRACO INC. P. 6. Box 1441 MINNEAPOLIS,

PRINTED IN U.S.A. 307-730 3-85 Revised 2-87

MN 55440-1444

700N Air Spray G-Gun”’ with

20 oz. Siphon Cup

Not Shown:

600N Air Spray G-Gun’”

34 oz. Siphon Cup

2 qt. Pressure Cup

2 gal. Non-ASME Pressure Tank

Portable Paint Pack

5’ Suction Tube Accessory

Not Shown:

.4mm Round Nozzle

.6mm Round Nozzle

.7mm Fan Nozzle

Paint Strainer

Paint Container with Lid

.5mm Fan Nozzle

.8mm Round Nozzle

45” Nozzle Extension Accessory

Paint Diffuser

Viscosity Measuring Cup

Pressure Washers

Chemical Injector

‘iv from your Painter’s Team products, use these convenient, time saving, optional

Brush

Foamer

Sandblast Kit

Sand Saver

Not Shown:

Quick-Prep”‘, General Purpose Cleaner

Quit-Kut’“, Degreaser

Quit-Klean”‘, Vehicle Wash

25’ x l/4 Airless Spray HOSe lnline Filter Kit

T-Gun

Contractor Tip

Fine Finish Tip

Reverse-A-Clean Tip

PT-Speed Brush - Available in 2’/2”

Tapered Trim or 4” Wall Brush with either

Nylon Poly or China Bristles

Low Pressure Spray Wand

Paint Pad

8-16’ Telescoping Extension

6-12’ Telescoping Extension

3’-6’ Telescoping Extension

High Pressure Conversion Valve

9” Roller Frame

9” Roller Cover - l/2” nap for semi-rough and smooth surfaces

9” Roller Cover - W for rough and semi- rough surfaces

9” Roller Cover - 1 l/4” nap for extra rough surfaces

3” Roller Frame

3” Roller Cover - l/2” nap for semi-rough and smooth surfaces

Dual Duty Fitting

Flush Adapter

Not Shown:

Airless Gun Adapter

25’ x ‘A” PVC Hose

25’ x

3/d’

Hose (for solvent based materials)

50’ x

3/d’

Hose (always use when pumping over 25 ft.)

Hose Connection (for 50’ lengths)

Nylon Suction Hose for Solvent Based

Materials

The professional line of Grace paint spraying and cleaning

THE GRACO WARRANTY AND DISCLAIMERS

WARRANTY

Grace warrants all equipment manufactured by it and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Grace distributor to the original purchaser for use. As purchaser’s sole remedy for breach of this warranty, Grace will, for a period of twelve months from the date of sale, repair or replace any part of the equipment proven defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Grace’s written recommendations. abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Grace component parts. Nor shall Grace be liable for malfunction, damage or wear caused by the incompatibility with Grace equipment of structures, accessories, equip- ment or materials not supplied by Grace, or the improper design, manufacture, installation, operation or maintenance of structures, ac- cessories, equipment or materials not supplied by Grace.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective for examination by Grace to verify the claimed defect. If the claimed defect is verified. Grace will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepatd. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the the costs of parts, labor and transportation.

DISCLAIMERS AND LIMITATIONS

THE TERMS OF THIS WARRANTY CONSTITUTE PURCHASER’S SOLE AND EXCLUSIVE REMEDY AND ARE IN LIEU OF ANY OTHER

WARRANTIES (EXPRESS OR IMPLIED], INCLUDING WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PAR-

TICULAR PURPOSE, AND OF ANY NON-CONTRACTUAL LIABILITIES, INCLUDING PRODUCT LIABILITIES, BASED ON NEGLIGENCE OR

CLUDED AND DENIED. IN NO CASE SHALL GRACO’S LIABILITY EXCEED THE AMOUNT OF THE PURCHASE PRICE. ANY ACTION FOR

BREACH OF WARRANTY MUST BE BROUGHT WITHIN TWO (2) YEARS OF THE DATE OF SALE.

EQUIPMENT NOT COVERED BY GRACO WARRANTY

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PAR-

TURED BY GRACO. These items sold, but not manufactured by Grace (such as electric motor, switches, hose, etc.), are subject to the warran- ty, if any, of their manufacturer. Grace will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

Factory

Subsidiary and Affiliate

GRACO INC.

Branches: Atlanta, Dallas, Detroit, Los Angeles, West Caldwell (N.J.)

Companies: Canada; England; Switzerland; France; Germany; Hong Kong;

Japan

P.O. BOX 1441 MINNEAPOLIS, MN 55440-1444

Printed I” USA 307.730 Wopyrlghl 1985, Gram Inc

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement