Graco 334599F, ProConnect Endurance Displacement Pump, Repair Owner's Manual
Add to My manuals24 Pages
advertisement
Repair
ProConnect Endurance
Displacement Pump
For professional use only.
Models: 17C487, 17C488, 17C489, 17C721, 17M992, 24Z731
334599F
EN
Important Safety Instructions
Read all warnings and instructions in this manual and related manuals.
Be familiar with the controls and the proper usage of the equipment.
Save these instructions.
Use only genuine Graco replacement parts.
The use of non-Graco replacement parts may void warranty .
ti24850b
Contents
Contents
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pressure Relief Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Dissemble Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Assemble Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Graco Standard Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2 334599F
Warnings
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.
WARNING
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion:
• Do not spray flammable or combustible materials near an open flame or sources of ignition such as cigarettes, motors, and electrical equipment.
• Paint or solvent flowing through the equipment is able to result in static electricity. Static electricity creates a risk of fire or explosion in the presence of paint or solvent fumes. All parts of the spray system, including the pump, hose assembly, spray gun, and objects in and around the spray area shall be properly grounded to protect against static discharge and sparks. Use Graco conductive or grounded high-pressure airless paint sprayer hoses.
• Verify that all containers and collection systems are grounded to prevent static discharge.
Do not use pail liners unless they are anti static or conductive.
• Connect to a grounded outlet and use grounded extensions cords. Do not use a 3-to-2 adapter.
• Do not use a paint or a solvent containing halogenated hydrocarbons.
• Do not spray flammable or combustible liquids in a confined area.
• Keep spray area well-ventilated. Keep a good supply of fresh air moving through the area.
• Sprayer generates sparks. Keep pump assembly in a well ventilated area at least 20 feet
(6.1 m) from the spray area when spraying, flushing, cleaning, or servicing . Do not spray pump assembly.
• Do not smoke in the spray area or spray where sparks or flame is present.
• Do not operate light switches, engines, or similar spark producing products in the spray area.
• Keep area clean and free of paint or solvent containers, rags, and other flammable materials.
• Know the contents of the paints and solvents being sprayed. Read all Safety Data Sheets
(SDS) and container labels provided with the paints and solvents. Follow the paint and solvents manufacturer’s safety instructions.
• Fire extinguisher equipment shall be present and working.
334599F 3
4
Warnings
WARNING
SKIN INJECTION HAZARD
High-pressure spray is able to inject toxins into the body and cause serious bodily injury. In the event that injection occurs, get immediate surgical treatment.
• Do not aim the gun at, or spray any person or animal.
• Keep hands and other body parts away from the discharge. For example, do not try to stop leaks with any part of the body.
• Always use the nozzle tip guard. Do not spray without nozzle tip guard in place.
• Use Graco nozzle tips.
• Use caution when cleaning and changing nozzle tips. In the case where the nozzle tip clogs while spraying, follow the Pressure Relief Procedure for turning off the unit and relieving the pressure before removing the nozzle tip to clean.
• Equipment maintains pressure after power is shut off. Do not leave the equipment energized or under pressure while unattended. Follow the Pressure Relief Procedure when the equipment is unattended or not in use, and before servicing, cleaning, or removing parts.
• Check hoses and parts for signs of damage. Replace any damaged hoses or parts.
• This system is capable of producing 3300 psi. Use Graco replacement parts or accessories that are rated a minimum of 3300 psi.
• Always engage the trigger lock when not spraying. Verify the trigger lock is functioning properly.
• Verify that all connections are secure before operating the unit.
• Know how to stop the unit and bleed pressure quickly. Be thoroughly familiar with the controls.
PRESSURIZED ALUMINUM PARTS HAZARD
Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious chemical reaction and equipment rupture. Failure to follow this warning can result in death, serious injury, or property damage.
• Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents.
• Do not use chlorine bleach.
• Many other fluids may contain chemicals that can react with aluminum. Contact your material supplier for compatibility.
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed.
• Read SDSs to know the specific hazards of the fluids you are using.
• Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.
PERSONAL PROTECTIVE EQUIPMENT
Wear appropriate protective equipment when in the work area to help prevent serious injury, including eye injury, hearing loss, inhalation of toxic fumes, and burns.
This protective equipment includes but is not limited to:
• Protective eye wear, and hearing protection.
• Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.
CALIFORNIA PROPOSITION 65
This product contains a chemical known to the State of California to cause cancer, birth defects or other reproductive harm. Wash hands after handling.
334599F
Pressure Relief
Trigger Lock
Always engage the trigger lock when sprayer is stopped to prevent the gun from being triggered accidentally by hand or if dropped or bumped.
Pressure Relief
Pressure Relief Procedure
This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashed fluid and moving parts, follow the Pressure
Relief Procedure whenever sprayer is stopped and before sprayer is cleaned or checked, and before equipment is serviced.
1.
Engage the trigger lock.
LineLazer ES 1000 ti24612a
LineLazer ES 1000 ti24851a
334599F 5
6
Pressure Relief
2.
Turn the ON/OFF switch to OFF position. Wait 7 seconds for power to dissipate.
6.
Turn pressure control to the lowest setting. Disengage trigger lock.
ti24852a
3.
Unplug power cord or shut engine off.
For LineLazer ES 1000, unplug power cord and disconnect battery.
4.
Engage the trigger lock.
5.
Remove tip guard.
ti24853a
LineLazer ES 1000 ti24854a
334599F
7.
Hold a metal part of the gun firmly to a grounded metal pail. Trigger the gun to relieve pressure.
Pressure Relief
9.
Open any fluid drain valves in system.
Leave drain valves open until ready to spray again.
ti24608a
8.
Engage the trigger lock.
ti24585a
334599F
LineLazer ES 1000 ti24855a
7
Pump Removal
Pump Removal
Pump removal includes disconnecting the fluid inlet and outlet and removing the pump.
1.
Use a hammer to loosen pump retaining nut.
4.
Disconnect outlet hose and suction hose from pump.
ti27248a
2.
Turn pump retaining nut to free pump rod cover.
ti27251a
5.
Slide pump out of the drive housing.
ti27252a ti27249a
3.
Swing pump rod cover open.
8 ti27250a
334599F
Repair
Repair
Dissemble Pump
1.
Remove packing nut and throat adjustment spacer. Retaining nuts are not removable and not sold separately.
3.
Dissemble intake valve. Clean and inspect. O-ring may require a pick for removal.
NOTICE
If using a pick to remove the O-ring use care to avoid damage to the machined surfaces.
Retaining
Nuts
ti24863a
2.
Unscrew cylinder from intake valve.
ti24874a ti24870a
334599F 9
Repair
4.
Tap piston rod out of cylinder with a hammer or flip over and tap piston rod out against a bench.
6.
Clean and inspect parts. (The piston has a special thread locking/sealing patch. Apply thread sealant to the threads. ti24875a
Do not clean or wipe the piston valve threads. Cleaning the piston valve threads could destroy the special sealing patch and cause the piston valve to come loose during operation, causing a pump burst and possible serious bodily injury.
5.
Unscrew piston valve from piston rod.
ti24876a ti24877a
10 334599F
7.
Remove and discard throat packing and glands from the cylinder.
Repair
Assemble Pump
1.
Soak leather packings in SAE 30W oil for one hour before assembly.
ti24890a
Leather
Packings
Leather
Packings ti24880a ti24893a
334599F 11
Repair
2.
Install ball in piston rod. If thread sealant is applied to piston valve threads, ensure that none gets on the ball.
4.
Assemble leather throat packings soaked earlier.
Leather
Packings ti24891a
3.
Torque to 27 ± 3 ft-lb (37 ± 4 N•m).
ti24893a
5.
Loosely install packing nut with o-ring onto cylinder.
ti24892a ti24894
12 334599F
6.
Apply liberal amounts of grease or oil to piston packings.
Repair
8.
Grease o-ring and place on outside diameter ring groove.
ti24895a
7.
Grease top inch or two of piston rod that will go through the cylinder throat packings. Gently guide displacement rod up through throat packings. Tap bottom of piston valve as necessary with a leather or plastic hammer.
ti24897a
9.
Clean seat thoroughly. Reassemble intake valve with a seat, ball, and new o-ring. Seat may be flipped over and used on other side.
ti24898a ti24896a
334599F 13
Repair
10. Torque to 100 ± 5 ft-lb (136 ± 7 N•m).
11. Install o-ring onto packing nut. Torque to 75 ± 5 in-lb (8.5 ± 0.5 N•m) or additional 1/2 turn from hand tight.
ti24899a ti24900a
14 334599F
12. Storage ti24901a
Repair
Throat Packing Adjustment
This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashed fluid and moving parts, follow the Pressure
Relief Procedure whenever sprayer is stopped and before sprayer is cleaned or checked, and before equipment is serviced.
When pump packings begin to leak after
much use, perform Pressure Relief
Procedure , page 5 and tighten packing nut
down until leakage stops or lessens. This allows approximately 100 gallons of additional operation before a repacking is required. Packing nut can be tightened without o-ring removal.
ti24988a
334599F 15
Parts
Parts
202
203
220
204
222
225
205
201
221
223
213
218
215
217
209
211
207
212
216
208
224
229
206
219
16 ti24903a
334599F
Parts
Parts List
Ref.
Part Description Qty.
201 24W617 ROD, displacement, 1 includes 212
202* 180656 BUTTON, plug
203 193047 NUT, packing
204* 176757 GLAND, female, throat 1
1
1
205* 176754 GLAND, male throat
206 24W619 CYLINDER, pump
1
1 includes 219, 229
207* 105444 BALL, sst, 0.3125 in.
1
208* 195129 GLAND, male piston 1
209* 180073 GLAND, female, piston 1
211* 15G234 GUIDE, piston 1
212 239937 VALVE, piston 1
(included with 201)
213 15C011 GUIDE, ball
215 246429 KIT, seat, carbide
1
1 includes 213, 217 and
218
216 15B611 VALVE, intake housing 1
217* 15B112 PACKING, o-ring 1
(0.941 in. OD)
218* 105445 BALL, sst, 0.5000 in.
1
Ref.
Part Description Qty.
219* 17V093 O-RING, PTFE
220* 160516 O-RING
221* 176755 V-PACKING, leather, throat
222* 192710 V-PACKING, throat,
V-Max
TM
3
UHMWPE, blue
223* 176749 V-PACKING, leather, piston
224* 192712 V-PACKING, piston,
V-Max
TM
2
3
UHMWPE, blue
225
Models 17C487, 17C488, 17C489, 17C721
17C231 FITTING, pump, QD, 1
1/4 npt
Model 17M992
162453 FITTING, 1/4 npt
229 NUTS, retaining, not sold separately
1
1
1
2
* - Also included in Kit 244194
- Also included in Kit 246429
334599F 17
Pump Installation
Pump Installation
Pump installation includes securing the pump and connecting to the fluid inlet and outlet.
1.
Connect outlet hose to pump.
ti24086a
2.
Move pump displacement rod up or down until it slides into the connecting rod when the pump is slid into the drive housing.
ti24087a
5.
Use both hands to tighten pump retaining nut.
ti24085b
3.
Slide pump all the way into drive housing. ti24088a
6.
Use a hammer to turn pump retaining nut an additional 1/8 to 1/6th turn or 45° to 60°.
ti25139a
4.
Close pump rod cover. Make certain that it is flush against drive housing.
1/8 - 1/6
7.
Install suction hose.
ti24089a ti24090a
18 334599F
Technical Specifications
Technical Specifications
PC Displacement Pump
US
3300 psi
Metric
228 bar, 22.8 MPa Maximum fluid working pressure.
Inlet/Outlet Sizes
Fluid inlet size
Fluid outlet size
Wetted materials on all models
1.0 in. diameter
1/4 in.
stainless steel, PTFE, leather, nylon, zinc-plated and nickel-plated carbon steel, tungsten carbide, chrome plating, UHMWPE, acetal, polyethylene, nylon
334599F 19
Notes
Notes
20 334599F
Notes
Notes
334599F 21
Graco Standard Warranty
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts.
Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY
OF FITNESS FOR A PARTICULAR PURPOSE .
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above.
The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH
ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED
BY GRACO . These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from
Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.
22 334599F
Graco Information
Graco Information
For the latest information about Graco products, visit www.graco.com
.
For patent information, see www.graco.com/patents .
TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor.
334599F 23
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions.
This manual contains English. MM 334599
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2014, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revision F, February 2018
advertisement