Graco 307614J Contractor Airless Spray Gun Owner's Manual

Add to my manuals
12 Pages

advertisement

Graco 307614J Contractor Airless Spray Gun Owner's Manual | Manualzz

INSTRUCTIONS-PARTS LIST

0-0

This manual contalns important warnings and Information.

READ AND RETAIN FOR REFERENCE

307-614

Rev J

"Contractor" Airless Spray Gun

3600 (252

bar) MAXIMUM WORKING PRESSURE

Model 220-955, Series A

Includes

RACC

IV DripLess" Tip Guard, 517 size

SwitchTip", and 2 finger trigger.

Four finger trigger is optional; see parts Ikt.

Model 235-990, Series A

Includes the Standard (non-reversing) DripLess"

Tip Guard and 4 finger trigger.

Spray tip not included. Order separately.

Model 217-593, Series

C

Includes the Standard (non-reversing) DripLess"

Tip Guard. Spray tip not included. Order separately.

Model 820-077, Series B

Includes RAC" IV DripLess" Tip Guard, 517 size

SwitchTip", and 2 finger trigger.

Four finger trigger Is optional; see parts list.

C€

How to

WARRANTY

..............................

How to Clean the Fliter

PARTS DRAWING

.......

...........

.......

....................

.........................

.......................

.............................

2

4

4

5

5

6

6 i i

12

Models 220-955,820-077

Model 217-593

GRACO INC. EO. BOX 1441 MINNEAPOLIS, MN 55440-1441

@COPYRIGHT 1983, GRACO INC.

High Pressure Spray Can Cause Serious Injury. For Professional Use Only.

Observe All Warnings. Read and understand all instruction manuals before operating equipment.

FLUID INJECTION

General Safety

This eauiDment oenerates verv hiclh fluid Dressure. Sprav from the gun, leaks otruptured components can inject fluid th;ough yourskinandintoyourbody,andcauseextremelyseriousinjury, including the need for amputation. Also, fluid injected or spiashedintotheeyesorontheskincancauseseriousdamage.

NEVERpointthespraygunatanyoneoratanypartofthebody.

NEVER put your hand or fingers over the spray tip. N M R to "blow back" paint; this is not an air spray system. try

HAZARD

Trigger Guard

Alwayshavethetriggerguardinpiaceonthegunwhenspraying to reduce the risk of accidentally triggering the gun if it is

dropped or bumped. See Fig 2.

Spray l i p Safety

. . mediately. ALWAYS foilow the PRESSURE RELIEF PROCE-

DURE, below, and then remove the spray tip to clean it.

ALWAYS have the tip guard in place on the spray gun when spraying.

NEVERwipeoffbuild-uparoundthespraytipuntilthepressure is fully relieved and the gun safety is engaged.

ALWAYSfollowthePRESSURERELlEFPROCEDURE. below, before cleaning or removing the spray tip or servicing m y sys- tem equipment.

NEVER try to stop or deflect leaks with your hand or body.

Besureequipmentsafetydevicesareoperatingproperlybefore each use.

Medical Alert--Airless Spray Wounds

If any fluid appears to penetrate your skin, get EMERGENCY

MEDICAL CARE AT ONCE.

DO

NOT TREAT AS A SIMPLE

CUT. leii the doctor exactly what fluid was injected.

Note to Physician: injection in the skin is a traumatic injury. it isimportanttotreattheinjurysurgicailyassoonaspossible.Do not delay treatment to research toxicity. Toxicity is a concern withsomeexoticcoatingsinjecteddirectlyintothebloodstream.

Consultation with aplasticsurgeon or reconstructive hand sur- geon may be advisable.

Pressure Relief Procedure

To reduce the risk of serious bodily injury, including fluid injection, splashing fluid or solvent in the eyes or on the skin, orinjuryfrom movingpartsorelectricshock. always follow this procedure whenever you shut off the sprayer, whencheckingorselvicinganypartofthespraysystem, when installing, cleaning or changing spray tips, and whenever you stop spraying.

1. Engage the trigger safety latch.

2. Shut off the power supply to the pump and close any bleed-type master air valves.

3. Disengagethetriggersafetylatch.Hoidametalpartof

Spray Gun Safety Devices ating properly before each use. Do not remove or modify any partofthegun;thiscancauseamalfunctionandresuitinserious bodily injury.

Trigger Safety Latch

Wheneveryoustopspraying,evenforamoment,aiwayssetthe gun safety latch in the closed or "safe" position, making the inoperative.Failuretosetthesafetylatchcanresultinaccidental triggering of the gun.

See Fig 1.

. gun

Diffuser

Thegundiffuserbreaksupsprayandreducestheriskoffluidin- jection when the tip is not installed. Check diffuser operation

regularly. See page 6.

Tip Guard

ALWAYS have the tip guard in piace on the spray gun while spraying. The tip guard alerts you to the fluid injection hazard and helps reduce, but does not prevent, the risk of accidentally placing your fingers or any part of your body close to the spray

tip. See Fig 2.

4. trigger the gun to relieve pressure.

Engage the trigger safety latch.

5. Open the pressure drain valve (required in system), having acontainer readyto catch thedrainage. Leave the valve open until you are ready to spray again.

If you suspecf that the spray tip or hose is completely clogged, orthatpressure hasnot beenfuilyrelievedafier following the steps above, VERY SLOWLY loosen the tip guard retaining nut or hose end coupling to relieve pres- suregradualiy, then loosen completely. Nowclearthetip or hose. -

HAZARD

Moving parts can pinch or amputate your fingers or other body parts. KEEP CLEAR of moving palts when starting or operating thesprayer. Followthe Pressure Relief Procedure, above, be- - of the sprayer, to prevent it

HAZARD

-

-

Duetothehighpressurefluidemined,astrongrecoiiactionmay occur when you trigger this gun. If you are unprepared, your hand could be forced back toward your body or you could lose your balance and fall, resulting in serious injury.

2 307-614

\~

EQUIPMENT MISUSE HAZARD

General Safety

NEVER alter or modify any Part of this equipment; doing so could cause it to malfunction.

Do

(252 bar) Maximum WorkingPressureto thegun. Besureallspray equipment and accessories used are as and So'vent manufacturer' Wear

,

Fluid and Solvent Compatibility

Allchemicalsusedinthesprayermustbechemicallycompatible

withthewetfedDartsshownintheTECHNlCALDATAonDaoe

11. Consult your chemic& supplier to ensure compatibility.-

HOSE SAFETY

High pressure fluid in the hoses can be very dangerous. If the hose develops a leak, split or rupture due to any kind of wear,

damageormisuse.thehighpressuresprayeminedfromitcan

cause a fluid injection injury or other serious bodily injury or property damage.

All fluid hoses must have strain rellefs on both ends1 The strainreliefshelpprotectthehosefromkinksorbendsatorclose to the coupling which can result in hose rupture.

Handle and route hoses carefully. of the pump and power supply.

Do

equipment. Keep hoses clear of moving parts and hot surfaces

Do

not pull on hoses to move not use fluids or solvents which are not compatible with the inner tube and cover of the hose.DONOTexposeGracohosestotemperaturesabove180"

F (82' C) or below -40" F (-40" C).

Tighten all fluid connections securely before each use. High pressurefluid can dislodgealoose coupling orallow high pres- sure spray to be emitted from the coupling.

Never use a damaged hose. Before each use, check the entire hose for cuts, leaks, abrasion, bulging cover, or damage or movementofthehosecouplings.Ifanyoftheseconditionsexist, replace the hose immediately. Do not try to recouple high pres- sure hose or mend it with tape or any other device. A repaired hose cannot contain the high pressure fluid.

Hose Grounding Continuity

Proper hose grounding continuity is essential to maintaining a groundedspray system. Checktheelectrical resistance of your fluidhosesatleastonceaweek.Ifyourhosedoesnothaveatag on itwhichspecifiesthemaximum electrical resistance, contact the hose supplier or manufacturer for the maximum resistance limits. Use a resistance meter in the appropriate range for your hose to checkthe resistance. If the resistance exceeds the rec- ommended limits, replace it immediately. An ungrounded or poorlygrounded hose can make your system hazardous. Also read FIRE OR EXPLOSION HAZARD, below.

FIRE

OR EXPLOSION HAZARD

Staticelectricity iscreated bythe flow of fluid through the pump and hose. If every part of the spray equipment is not properly grounded. sparking may Occur, and the System may become hazardous. Sparking may also occur when plugging in or un- plugging a power supply cord or using a gasoline engine.

Sparks can ignite fumes from SOlVentS and the fluid being spraved, dust Dafticles and other flammable substances, wheiher you arespraying indoors or outdoors, and can cause a fire age. explosion and serious bodily injury and property dam-

Do

not plug in or unplug any power supply cords using this equipment, stop until the problem has been identified and corrected. in the

Ifyouexperienceanystaticsparkingorevenaslightshockwhile spraylng Immediately. Check the entiresystemforpropergrounding.Donduselhesystemagain

1. Pump orsprayer: provide appropriate grounding as recom- mended in your pump or sprayer instruction manual.

2.

4.

7.

500

.- . . to ensure grounding continuity. See Hose Grounding Continuity, above.

5. Fluid suppiy container: according to local code.

6.ANSOl~entpailsusedwhenflushing,ac~rdingtolOCalcode. pail on a

Do not Dlacethe board, which interrupts the grounding continuity.

To fl (150 m) combined hose length being sprayed: according to local maintain grounding continuity when flushing of a grounded metal pail, then trigger the gun. or relieving pressure,alwaysholdametalpartofthegunfirmlytotheside

Grounding

To reduce the risk of static sparking, ground the sprayer and all otherspray equipment used or located inthespray area. Check yourlocalelectricalcodefordetailedgrounding instructionsfor your area and type of equipment. Be sure to ground all of this spray equipment:

Flushing Safety

To reduce the risk of fluid injection injury, static sparking, or splashing, be sure the system is properly grounded, relieve pressure, remove spray tip. Hold a metal part of the gun firmly to the side of a grounded metal pail and usethe lowest possible fluid pressure during flushing.

IMPORTANT

Unlted States Government safety standards have been adopted under the Occupational Safety and Health Act. These standards particularly the General Standards, Part 1910, and the Construction Standards, Part 1926

- should be consulted.

-

307-614 3

4

System Requirements

Installation/Operation

WARNING

Keep the wallet-sized warning card provided with this gun with the operator at all times. The card contains important treatment information should an injection injury occur. Additional cards are available at no charge from Gram Inc.

How to Use the Gun

1.

2.

Connect a grounded fluid hose to the gun inlet.

See Fig 2.

With no tip installed, start the pump. Flush the pump according to the instructions supplied with it. Prime the system with the material.

3. Follow the Pressure Relief Procedure on page

2. Be sure the trigger safety latch is engaged. See

Fig 1.

WARNING

Be sure your system has a bleed-type master air valve (pneumatic pumps only) and a pressure drain valve. These accessories help reduce the risk of serious bodily injury, including fluid injec- tion, splashing in the eyes or on the skin, or injuly from moving parts, if you are adjusting or repairing the pump or gun.

.

.

4. Model 217-593 & 235-990; unscrew the tip guard (3) and install the tip (A) and gasket (2) in the nut of the tip guard. Screw the assembly firmly onto the gun. lighten with a wrench. See

Fig 2.

1. The bleed-tvomer air valve (air-powered pumps only) relieves air trapped between this valve and the pump after the air regulator is shut

off.

Trapped air can cause the pump to cycle unexpectedly.

NOTE: Failure to install the gasket (2) will result in leaking.

5. W e l s 2 2 0

307-848,

-

-

2.

:

SwitchTip (40) and tip guard (41). See manual

2. The pressure drain

v&

assists in relieving fluid pressure in the displacement pump, hose and gun; triggering the gun to relieve pressure may not be sufficient.

3. Strain the fluid you are spraying if it contains particles which could clog the spray tip.

How to Use the Trigger Safety Latch

1. To engage the trigger safety latch (ON SAFE), turn the latch to a right angle with the gun body.

See Fig 1.

2. To disengage the trigger safety latch (OFF SAFE), push the latch out and turn it parallel with the gun body.

Fig

2 3 ormr

6. Start the pump. Adjust the fluid pressure until the spray is completely atomized. Use the lowest pressure necessary to get the desired results.

Higher pressure may not improve the spray pattern and will cause premature tip and pump wear.

7. If adjusting the pressure does not give a good spray pattern, follow the Pressure Relief Proce-

dure on page 2

and then try another tip size.

8. Use a full-open, full-close trigger action. Hold the gun about 14 in. (350 mm) from and at right angles to the work surface. Don't swing the gun in an arc. Practice to find the best length and speed of stroke.

307-614

\

f,

I

A

Installation/Operation

1. To adjust the spray pattern direction, follow the

Pressure Relief Procedure on page 2.

Loosen the tip guard retaining nut (e). Turn the tip guard/ tip groove horizontally (C) for a horizontal pattern and vertically (A) for a vertical pattern. Tighten the nut.

2. Clean the front of the tip frequently during the day to help reduce buildup. Also clean the tip and tip guard at the end of each work day. Use a solvent- soaked brush to clean the spray tip.

Clearing an obstruction

If the spray tip clogs while spraying, immediately stop spraying, then:

Gun217

-

593,3235

- - with standard ti0 a u d

2. The spray tip orifice and spray angle determines the coverage and size of pattern. When more coverage is needed, use a larger spray tip rather than increasing fluid pressure.

Openings in the tip guard reduce paint buildup on the guard while spraying. Any damage to the sharp edges of the openings causes paint to collect at that area. Never hang the gun by the tip guard. r vertical spray pattern

Tip guard shown in position for horizontal spray pattern

1. Engage the trigger safety latch, open the pres- sure drain valve.

2. Remove the spray tip and blow out the obstruc- tion by applying air to the front of the spray tip.

Or, let the spray tip and gun nozzle soak to dissolve the obstruction. If it won't dissolve, jar it out by tapping the back of the spray tip against a flat surface.

Never soak the entire gun in solvent. Prolonged

I C A U T I O N

1

Sun 220-955 & 820-077 -with RAC IV tiD auard

1. Engage the trigger safety latch. Rotate the RAC IV tip handle 180'.

See Fig 4.

2. Disengage the safety latch. Trigger the gun into a pail or onto the ground to remove the clog.

3. Engage the safety latch. Rotate the tip handle to the spraying position. How

toclean the Spray Tip and Clear

a

Spray Tip Obstruction

To reduce the risk of fluid injection the eyes or

WARNING

on the skin, do not or splashing in hold a hand, body or rag in front of the spray tip when cleaning or checking a clogged tip. Point the gun toward the ground or into a waste container when checking to see if the spray tip is cleared.

DO NOT try to "blow back" paint; this is NOT an air spray gun.

DO NOT wipe fluid buildup until pressure is relieved.

off

the gun or spray tip

I

Cleanlng during the day

1. Follow the Pressure Relief Procedure on page

2.

4. If the tip is still clogged, engage the safety latch, shut

off

the sprayer and disconnect the power source, and open the pressure drain valve to re- lieve pressure. Clean the spray tip as shown in manual 307-848, supplied with the RAC IV.

KEY hanie 180' and

T I trigger gun to clear clog.

Fig

4

307-614

Me4

5

Installation/Operation

How to Check the Gun Diffuser Operation

Check the diffuser operation weekly. The gun diffuser/ seat (A) breaks up spray and reduces the risk of fluid injection when the tip Is not installed. Petform the test below. If it fails, replace the entire Needle Kit, Part No.

218-070,

as instructed on page 7.

Diffuser/seats are not sold separately since the gun will leak if an old needle is used with a new diffuser/seat.

Flg 5

1. Follow the

2.

Pressure Relief Procedure on page

2. Remove the tip guard and spray tip.

3. Start the sprayer and adjust it to the lowest pressure.

-

4. Aim the gun into a grounded metal pail while holding.it firmly to the pail. Trigger the gun. If the fluid emitted Is not diffused into an irregular stream, replace the entire needle kt immediately.

See

Fig 5.

How to Clean the Filter

See Fig 6.

Normal daily system flushing removes most buildup on the filter (17). For a weekly cleaning:

1.

Follow the Pressure Relief Procedure on page 2.

2. Remove the screw (14).

3. Push up on the trigger guard (12) and swing it away from the trigger (5).

4. Unscrew the gun handle from the housing (26).

Remove the filter and clean it in compatible solvent.

5.

Apply lithium-base grease.to the threads of the fluid tube (19) and reassemble the gun.

How to Flush the Gun

Always flush the pump and gun before the fluid being sprayed can dry in it.

NOTE If it is available, the flushing procedure provided in your pump or sprayer manual should be used instead of this procedure.

6. Now trigger the gun into the solvent pail. Circulate the fluid until the system is thoroughly flushed.

7. Follow the Pressure Relief Procedure

on page

WARNING

including splashing fluid in the eyes or on the skin, or static electric discharge when flushing:

0

0

0

0

Be sure the entire system, including flushing pails, are properly grounded.

Remove the tip guard and spray tip.

Maintain metal to metal contact between the gun and the flushing pail.

Use the lowest possible pressure.

1. Follow the Pressure Relief Procedure on page

2.

2. Remove the tip guard and spray tip. Soak and clean the parts.

3. Put the pump intake in a grounded pail of water

6 or solvent.

307-614

Fig 6

4. Start the pump at its lowest pressure.

5.

I. i i i i

I

i

(9-10 N.m) - - m m

NOTE The needle (C), diffuserlseat (A), gasket included in Kit 218-070.

(B) and locknut (C) must be replaced together. They are

Disassembly

(See Fig 7)

1. Follow the Pressure Relief Procedure on page

2.

2. Remove the tip guard assembly. See Fig 2.

Service

4. If the gun handle (6) was removed, hand tighten it into the fluid housing (26); it should if

fit

easily. Only handle with the fluid housing and torque the setscrew to 80-90 in-lb (9-10 Nm).

3. Squeeze the trigger while unscrewing the diffuser/ seat (A) and gasket (B).

5. Adjust the needle before using the gun. Procs dure below.

6. Be sure the trigger guard and tip guard are installed before using the gun.

Adjusting the needle

(See Fig

8)

1. Engage the gun safely latch.

2. Hold the gun with the nozzle straight up so the trigger falls onto the safely latch.

3. With light pressure, hold the trigger against the latch. Turn the locknut (D) clockwise until there is enough tension for you to feel raise slightly off the latch. and see the trigger

4. Turn the adjusting nut 3/4 turn counterclockwise.

5. Connect the fluid hose. Install the tip guard and prime the system. Trigger the gun and release it.

The fluid flow should stop immediately. Engage the safely latch and try to trigger the gun. No fluid should flow. If the gun falls either test, relieve pressure, disconnect the hose and readjust the needle.

4. Remove the locknut (D) and end cap

(23).

5. Tap the rear of the gun with a plastic mallet to push the needle assembly out the front.

Reassembly

(See Fig 7)

1. Guide the threaded end of the needle assembly into the front of the gun.

2. Install the end cap, aligning its guides with the holes in the rear of the gun. Install the locknut (D) loosely.

3. Squeeze the trigger while installing the gasket and diffuser/seat (A). Torque the diffuser seat to

20-25 ft-lb (27-34 N.m).

(B)

A

A

Engage trigger safety latch

Arrows indicate clockwise lum

8 01705

307-614 7

Model 220-955, Series A

Includes items

1 and 4

to 41

Model 235-990, Series

Includes items 1 to 39

A

Model 217-593, Series C

Includes items 1 to

39

Model 820-077, Series

Includes items 1 to

39

B

15

/

O l m B

No.

1 218-070

2 V 166-969

3

4

5

5a

220-251

100-421

179-734

179-943

6

lOA

Part No.

172-479

11A 179-761

12

13

14

15

16

179-724

179-730

101-666

218-021

179-750

17V 218-131

17a 218-133

18

8

218-643

179-731

307-614

Description

NEEDLE-DIFFUSEWSEAT KIT

GASKET, tip (used with flat tips only)

TIP GUARD

SETSCREW, soc hd, 5/16-18x 3/13'

2 FINGER TRIGGER (standard)

4 FINGER TRIGGER

(Model 235-990 only)

GUN HANDLE ASSEMBLY

Includes replaceable items 4,

13, 14

INSTRUCTION TAG

WARNING TAG

TRIGGER GUARD

GUARD RETAINER

SCREW, 8-32 X 5/16"

SWIVEL

SPRING RETAINER

FLUID FILTER ASSEMBLY

(standard 50 mesh) Includes replaceable items 21 16, 18, 20,

FLUID FILTER ASSEMBLY

(optional 100 mesh) Includes replaceable items

(standard 50

16, 18a. 20.21a

STRAINER ELEMENT w.

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

Ref.

No. Part No. Descrlptlon

QtY.

18a 179-732 STRAINER ELEMENT

19

20

(optional 100 mesh)

179-721 FLUIDTUBE

179-763 SPRING

21 179-722 SPRING RETAINER (color coded blue)

(for standard 50

21a 179-957 SPRING RETAINER (color coded orange)

100 mesh filter)

1

(for optional

22V 179-733 GASKET

23

26

31

32

179-720 ENDCAP

179-718 FLUID HOUSING

105-334 LOCKNUT; M4x0.7

177-538 TRIGGER STUD thread

33

37

179-737 ACTUATOR PIN

179-729 NEEDLE HOUSING

39A 222-385 WARNING CARD (not shown)

40V 221 -517 SWITCHTIP SPRAY TIR

41V 220-422 RAC IV

SZ

DripLess TIP GUARD

See manual 307-848 for parts

1

1

1

1

1

2

1

1

1

1

1

1

1

1

A

Replacement Danger and Warning labels, tags and cards available at no cost.

V Keep these spare park on hand to reduce down time.

i

307-614

9

Accessories

SWIVELS

and

WHIP HOSES FILTERS

3000

(210 bar) Maximum Working

Adequate filtering is important for a good surface finish and to minimize tip clogging. These filters provide secondary filtering. Elements are available in various mesh sizes.

Pressure.

Swivels and whip hoses provide more flexible gun movement for easier handling and less fatigue.

Working pressures are listed in the descriptions.

214-925 Swivel, 1/4 npsm

x

3/8

5000 psi (350 bar) Max. npt(9

Working Pressure

213-068 Includes filter body, spring and one

100 mesh screen.

207-946 Swivel, 1/2 npsm x 3/8 npt(f)

5000 psi (350 bar) Max. Working Pressure

213-069 Includes filter spring and one

60 mesh screen.

Use with above filter body.

204-940 Swivel, 1/4 npt x 1/4 npsm

3000 psi (210 bar) Max. Working Pressure

210-724 Includes filter spring and one

100 mesh screen.

Use with above filter body.

-

214-701 Whip hose, nylon, coupled 1/4 npsm(fj

x

3/8 npt(m), spring guards both ends.

3000 psi (210 bar) Max. Working Pressure

210-729 Includes assembly 213-068 plus a

3 fl(O.9 m) whip hose for more flexible gun movement.

224-456

-

TIP GUARDS

220-422

210-500 Includes swivel, adapter and one

60 mesh screen

These tip guards fit all Graco airless spray guns.

Choose the one that’s right for your application. One of these tip guards is included with every Graco airless gun.

RAC@ IV Dripless” Tip Guard. Includes

SwitchTip of choice. See your distributor for available sizes.

ReDlacement elements for above filters

210-731 Three 60 mesh

(250

210-732 Three 100 mesh (149 micron) screens

210-733 Three 200 mesh (74 micron) screens

TOOLS

Nylon Brushes

Use to thoroughly clean the gun’s fluid passages.

220-222 Standard DripLess” Tip Guard. Order flat tip separately. See your distributor for available sizes.

101-891

101-892

0.375” (9 mm) dia.

0.625” (16 mm) dia.

222-674 Heavy Duty R A P Dripless” Tip Guard.

Order SwitchTip separately. See your distributor for available sizes.

10 307-614

i

Technical Data

Maximum Working Pressure

Fluid Orifice Size

Wetted Parts

Weight

Inlet

Sound Data

Sound Pressure Level

Sound Power Level

......

3600 psi (252 bar)

0.125 in. (3.18

...................

78 dB(A)*

Measured while spraying waterbase paint

1.36 through a 517 tip at 3,000 psi (207 bar).

Per IS0 3744

mm)

Zinc-plated carbon steel

Stainless steel, Polyethylene,

Polyurethane, Nylon,

1/4

18 oz.

PTFE

(510 g) npsm(m) swivel

.................

- gravity

PTFE a registered trademark of the

Company.

Grace Phone

Numbers

TO PLACE AN ORDER, contact your Graco distrib- utor, or call this number to identify the distributor closest to you: 1-800-328-0211 Toll Free.

FOR TECHNICALASSISTANCE, service repair information or assistance regarding the application of

Graco equipment: 1-800-543-0339 Toll Free.

Manual Change

Summary

Added CE logo to front page.

Added Warning data to page 2.

Added Sound Data to page 11.

307-614 11

The Graco Warranty

and

Disclaimers

WARRANTY

Graco warrants all equipment manufactured by it and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor lo the original purchaser for use. As purchaser's sole remedy for breach ofthis war- ranty, Gram will, f0r.a period of twelve months from the date of sale, repair or replace any part of the equipment proven defective.

This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco's written recom- mendations.

This warranty does not cover, and Graco shall not be liable for, any malfunction, damage or wear caused by faulty installation, mis- application, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-

Graco component pa*. Nor shall Graco be liable for malfunction, damage or wear caused by the Incompatibility with Gram equipment of structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installa- tion, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claim. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor and transportation. -~

DISCLAIMERS AND LIMITATIONS

The terms of this warranty constitute purchaser's sole and exclusive remedy and are in lieu of any other warranties (express or implied), Including warranty of merchantability or warranty of fitness for a partlcular purpose, and,of any non-contractual liabilities, including product liabilities, based on negligence orstrict liability. Everyform of liabiiifordirect, special or consequential damages or loss is expressly excluded and denied. In no case shall Gram's liabiiity exceed the amount of the purchase price. Any action for breach of warranty must be brought within two (2) years of the date of sale.

EQUIPMENT NOT COVERED BY GRACO WARRANTY

Graco makes no warranty, and disclaims all implied Warranties of merchantabllity and fitness for respect to accessories, equipment, materials, or components sold but not manufactured by Graco. These items sold, but not manufactured by Graco (such as electric motor, switches, hose, etc.) are subject to the warranty, if a particular purpose, with any, of their manufacturer.

Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

(

..- i

Sales OfIices: Atlanta, Chicago, Dallas, Detroit, Los Angeles, Mt. Arlington (N.J.)

Foreign Offices: Canada: England; Korea; Switzerland; France; Germany; Hong Kong: Japan

GRACO INC. P.0. BOX 1441 MINNEAPOLIS, MN 55440-1441

PRINTED IN U.S.A. 307-614 5/83 Revised 1/95

12 307-614

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement