Graco 307614F AIRLESS SPRAY GUN Owner's Manual

Add to my manuals
8 Pages

advertisement

Graco 307614F AIRLESS SPRAY GUN Owner's Manual | Manualzz

INSTRUCTIONS-PARTS LIST.

G

'

Rev

SUPERSEDES E

This manual contains IMPORTANT

WARNINGS and INSTRUCTIONS

READ AND RETAIN FOR REFERENCE

AIRLESS SPRAY GUN

3@Xl psi (252 MAXIMUM WORKING PRESSURE

WARNING

I h

Hazard of Using Fluids Containing Halogenated Hydrocarbons

Never use 1.1.1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents in this equipment. Such use could result in a serious chemical reaction, with the possibility of explo- sion, which could cause death, Serious bodily injury andfor substantial property damage.

Consult your fluid suppliers to ensure that the fluids being used are compatible with aluminum and zinc parts. f

GRACO INC. P.O. Box I441 MINNEAPOLIS, MN 55440-1444

@COPYRIGHT 1983 GRACO INC.

HIGH

PRESSURE SPRAY CAN CAUSE SERIOUS INJURY.

FOR

PROFESSIONAL USE ONLY. OBSERVE ALL WARNINGS.

Read and understand all instruction manuals before operating

equipment.

FLUID INJECTION HAZARD

G e n e r a l Safety

Airless spray equipment generates very high fluid pressure.

Spray from the gun, leaks or ruptured components can inject fluid through your skin and into your body and cause extreme- ly serious bodily injury, including the need for amputation.

Also, fluid injected or splashed into the eyes or onto the skin can cause serious damage.

S p r a y Tip S a f e t y

Use extreme cautlon when cleaning or changing spray tips. If the spray tip clogs while spraying, engage the gun safety latch immediately. ALWAYS follow the Pressure Relief Pro- cedure, below, and then remove the spray tip to clean it.

NEVER wipe off build-up around the spray tip until pressure is fully relieved and the gun safety latch is engaged.

NEVER point the spray gun at anyone or at any part of the body. NEVER put hand or fingers over the spray tip. NEVER try to "blow back" paint; this is NOT an air spray gun.

ALWAYS have the tip guard in place on the spray gun yhen spraying.

Pressure R e l i e f P r o c e d u r e

To reduce the risk of serious bodily injury, including fluid injec- tion; splashing in the eyes or on the skin; or injury from mov- ing parts, always follow this procedure whenever you shut off the spray equipment, when checking or servicing any part of the spray system. when installing, cleaning or changing spray tips, and whenever you stop spraying. ALWAYS follow the Pressure Relief Procedure, t o the right, before cleaning or removing the spray tip or servicing any system equipment.

NEVER try to stop or deflect leaks with your hand or body.

Be sure equipment safety devices are operating properly before each use.

M e d i c a l A l e r t - A i r l e s s Spray Wounds

If any fluid appears to penetrate your skin, get EMERGENCY

MEDICAL CARE A T ONCE. DO NOT TREAT A S A

SIMPLE CUT. Tell the doctor exactly what fluid was injected.

1. Engage the gun safety latch.

2. Shut off the power supply to the pump and close any bleed-type master air valves in the air supply.

3. Disengage the gun safety latch.

4. Hold a metal part of the gun firmly to the side of a ground- ed metal pail, and trigger the gun into the pail to relieve pressure.

5. Engage the gun safety latch.

6. Open the pump fluid drain valve (required in the system), having a container ready to catch the drainage.

7. Leave the drain valve open until you are ready to spray again.

Note to Physician: Injection in the skin is a traumatic in- jury. It is important to treat t h e injury surgically as soon es possible. Do not delay treatment to research toxicity.

Toxiciiy is a concern with some exotic coatings injected directly into the blood stream. Consultation with a plastic surgeon or reconstructive hand surgeon may be advisable.

If you suspect that the spray tip or hose is completely clogged, or that pressure has n o t been fully relieved after following the steps above, VERY SLOWLY loosen the tip guard retaining nut or hose end coupling and relieve pressure gradually, then loosen completely. Now clear the tip or hose.

S p r a y Gun S a f e t y Devices

Be sure all gun safety devices are operating properly before each use. DO not remove or m o d w any part of the gun; this can cause a malfunction and result in serious bodily injury.

Safety L a t c h

Whenever you stop spraying, even for a moment, always engage the gun safety latch in the closed or ON SAFE posi- tion, making the gun inoperative. Failure to engage the safety latch can result in accidental triggering of the gun. See Fig 2,

page 4.

Diffuser

The gun diffuser breaks up spray and reduces the risk of fluid injection when the tip is not installed. Check diffuser operation regularly. Follow the Pressure Relief Procedure, below, then remove the spray tip. Aim the gun into a grounded metal pail, holding the gun firmly to the pail. Using the lowest possi- ble pressure. trigger the gun. into an irregular stream, replace the diffuser immediately.

Tip Guard

ALWAYS have the tip guard in place on the spray gun while spraying. The tip guard alerts you to the fluid injection hazard and helps reduce, but does not prevent, the risk of accidental- ly placing your fingers or any part of your body close to the spray tip.

Trigger Guard

NEVER operate the gun with the trigger guard removed. The trigger guard reduces the risk of accidentally triggering the gun if it is dropped or bumped.

EQUIPMENT MISUSE HAZARD

G e n e r a l S a f e t y

Any misuse of the spray equipment or accessories, such as overpressurizing, modifying parts, using incompatible chemicals and fiuids, or using worn or damaged parts, can cause them to rupture and result in fluid injection or other serious bodily injury, fire, explosion or property damage.

NEVER alter or modify any part of this equipment; doing so could cause it to malfunction.

CHECK all spray equipment regularly and repair or replace worn or damaged parts immediately.

Read and follow the fluid and solvent manufacturer's literature regarding the use of protective eyewear, respirator, clothing and equipment.

S stem P r e s s u r e

08 NOT exceed 36w p s i 1252 bar) MAXIMUM WORKING

PRESSURE to the gun. Be sure all accessory items and system components are rated to withstand the pressures developed. NEVER exceed the pressure rating of any compo- nent in the system.

Fluid Cornpetibi1,ity

BE SURE that all flulds and solvents used are chemically com-

Datible with the wetted Darts shown in the Technical Data on the back cover. Alwais read the manufacturer's literature before using a fluid or solvent in the system.

('.

(.

!

FIRE OR EXPLOSION HAZARD

Static electricity is created by the high velocity flow through the pump and hose. of fluid

If every part of the spray equip- ment is not properly grounded, sparking rnay occur, and the system may become hazardous. Sparking rnay also occur when plugging in or unplugging a power supply cord. Sparks can ignite fumes from solvents and the fluid being sprayed, dust particles and other flammable substances, whether you are spraying indoors or outdoors; and can cause a fire or ex- plosion and serious bodily injury and property damage. Do not plug in or unplug any power supply cords in the spray area when there is any chance of igniting fumes still in the air.

If you experience any static sparking or even a slight shock while using this equipment, STOP SPRAYING IM-

MEDIATELY. Check the entire svstem for moper grounding.

Do not use the system again untii the Droblem.hasbeen idei- tified and corrected.

G r o u n d i n g

To reduce the risk of static sparking, ground a11 the spray equipment used or located in the spray area. CHECK your local electrical code and your equipment's individual instruc- tion manuals for detailed grounding instruction6 for your area and type of equipment and be sure t o ground all of this spray equipment:

1. Pump or sprayer: as instructed in your separate pump or sprayer manual.

2. Air compressor or hydraulic power supply: according t o local code.

HOSE SAFETY

High pressure fluid in the hoses can be very dangerous. hose develops a leak, split or rupture due to any kind of wear, damage or misuse. the high pressure spray emitted from

If it the can cause a fluid injection injury or other serious bodily injury or propem damage.

ALL FLUID HOSES M U S T HAVE SPRING GUARDS O N

BOTH ENDS1 The spring guards help protect the hose from kinks or bends at or close to the coupling which can result in hose rupture.

TIGHTEN all fluid connections securely before each use. High pressure fluid can dislodge a loose coupling or allow high pressure spray to be emitted from the coupling.

NEVER use a damaged hose. Before each use, check the en- tire hose.for cuts, leaks, abrasion, bulging cover, or damageor movement of the hose couplings. If any of these conditions exist, replace the hose immediately. DO NOT try t o recouple high pressure hose or mend it with tape or any other device. repaired hose cannot contain the high pressure fluid.

A

MOWING PARTS HAZARD

Moving parts can pinch or amputate your fingers or other body parts. KEEP CLEAR of moving parts when starting or operating your system. Disconnect the power source and relieve Dressure bv followino the Pressure

on page

Rellef Procedure

2

before checking o"r servicing your system t o prevent the pump from cycling accidentally.

3. Fluidhoses: use only grounded hoses with a maximum of

500 feet (150 m) combined hose length t o ensure ground- ing continuity. Refer t o Hose Grounding Continuity. below.

4. Spray gun: obtain grounding through connection t o a properly grounded fluid hose and sprayer or pump.

5. Fluid supply container: according t o local code.

6. Object being sprayed: according to local code.

7. code. Use only metalpails, which are conductive. Do not place the pail on a nonconductive surface, such as paper or cardboard, which interrupts the grounding continuity.

8. To maintain grounding continuiiy when flushing or reliev- ingpressure, always hold a metal part of the gun firmly to the side of a metal pail, then trigger the gun.

Flushing S a f e t y

Before flushing, be sure the entire system and flushing pails are properly grounded. Refer to Grounding. above. Follow the Pressure Relief Procedure on page 2, and remove the spray tip from the gun. Always use the lowest possible fluid pressure, and maintain firm metal-to-matal contact between the gun and a grounded metal pail during flushing t o reduce the risk of a fluid injection injury, static sparking and splashing.

HANDLE AND ROUTE HOSES CAREFULLY. Do not pull on hoses to move equipment. Do not use fluids or solvents which are not compatible with the inner tube and cover of the hose.

DO NOT expose Graco hose to temperatures above l W F

( W C I or below 40°F (-40°Cl.

H o s e G r o u n d i n g C o n t i n u i t y

Proper hose grounding continuity is essential t o maintaining a grounded spray system. Check the electrical resistance of your air and fluid hoses at least once a week. If your hose does not have a tag on it which specifies the maximum electrical resistance, contact the hose supplier or manufacturer for the maximum resistance limits. Use a resistance meter in the ap- propriate range for your hose t o check the resistance. If the resstance exceeds the recommended limits, replace it im- mediately. An ungrounded or poorly grounded hose can make your system hazardous. Also read FIRE OR EXPLOSION

HAZARD, above.

TERMS

W A R N I N G : Alerts user to avoid or correct that could cause bodily injury. conditions

CAUTION: Alerts user to avoid or correct conditions that could damage t h e equipment.

NOTE: Gives special procedures or information.

IMPORTANT

United States Government safety standards have been adopted under the Occupational Safety and Health Act. These standards-par- ticularly the General Standards, Part 1910, and the Construction Standards, Part 1928-should be consulted.

307-614 3

INSTALLATION

NOTE:

Numbers and letters in parentheses in the text correspond to the reference numbers and letters in the drawings and parts list.

W A R N I N G

Be sure your system has

a

bleed-type master air valve (pneumatic pumps only) and a fluid drain valve. These two accessories help reduce the risk of serious bodily injury, including fluid injection, splashing in the eyes or on the skin, or injury from moving parts, if you are adjusting or repairing the pump or gun.

1. The bleed-type master air valve relieves air trap- ped between this valve and the pump after the air regulator

is

shut off. Trapped air can cause the pump to cycle unexpectedly.

2. The fluid drain valve assists in relieving fluid pressure in the displacement pump, hose and gun; triggering the gun to ralieve pressure m y not be sufficient.

1. Connect a grounded fluid hose to the gun inlet.

2. With no tip installed, start the pump/sprayer. Flush it according to the instructions supplied with it.

Prime the system with the fluid you are using.

3.

Follow the Pressure Relief Procedure on page 2.

4. Model 217-593: with the gun safety latch engaged, unscrew the tip guard (3) and install the tip (6) gasket (2) assembly firmly onto the gun. Tighten with a wrench. See Fig 1.

OPERATION

WARNING

of serious bodily injury, in- cluding fluid injection or splashing in the eyes or on the skin, always follow the Pressure Relief Pro-

cedure on page 2

before checking, servicing, in- stalling, removing, changing or cleaning sprai tips I or any part of the gun or system.

Whenever you stop spraying for

a

engage the gun safety latch. See Fig 2. moment,

I

NOTE:

Failure

to

install the tip gasket (2) stalling

a

flat tip will result in leaking.

5. Model220955: with the gun safety latch engaged, install the SwitchTipTM (41). Refer to manual

307-848, supplied.

6. Strain the fluid you are spraying if it contains par- ticles which could clog the spray tip.

3. Use a full-open, futl-close trigger action. Hold the gun about 14 in. (350 mm) from and a t right angles to the work surface. Don't swing the gun in an arc.

Practice to find the best length and speed of stroke.

WARNING

gun should be kept with the operator at all times.

The card contains important treatment information should an injection injury occur. Additional cards

1. Start the pump. Adjust the fluid pressure so the spray is completely atomized. Always use the lowest pressure necessary to get the desired results.

Higher pressure may not improve the spray pattern and will causa premature tip and pump wear.

2. If adjusting the pressure does not give

a

good spray pattern, try another tip size. Ba sure to relieve pressure completely before changing tips.

TO ENGAGE SAFETY

LATCH ION SAFE1

PULLOUT LATCH

AND TURN TO RIGHT

ANGLE WITH BODY

TO DISENGAGE SAFETY

LATCH IOFFSAFEITURN

LATCH PARALLELTO

4 307-614

Adjust the Spray Pattern

1. To adjust the spray pattern direction, follow the

Pressure Relief Procedure on page 2.

Engage the safety latch and loosen the tip guard retaining nut.

Turn the tip guardltip groove so it is horizontal for a horizontal spray pattern, and vertical for a vertical pattern. Tighten the nut.

2. The spray tip orifice size and spray angle determines the coverage and size of pattern. When more coverage is needed; use a larger spray tip rather than increasing fluid pressure.

WARNING

To reduce the risk of a fluid injection injury,

NEVER use the gun with the tip guard or trigger guard removed.

CAUTION

Cleaning and Clearing the Spray Tip

WARNING

To reduce the risk of a fluid injection or splashing in the eyes or on the skin, DO NOT hold your hand, body, or a rag in front of the spray tip when cleaning or checking a clogged tip. Always point the gun toward the ground or into a waste con- tainer when checking to see if the spray tip is cleared.

DO NOT try to "blow back" paint; this is NOT an air spray gun.

I

DO NOT wipe fluid buildup off the gun or spray tip until pressure is relieved. See the Pressure Relief

Procedure Warning on page 2.

Clean off the front of the tip frequently during the day's operation and at the end of the work day. Always follow

the Pressure Relief Procedure Warning on page 2.

Then use a solvent soaked brush to clean the spray tip and to keep fluid buildup from drying and clogging the spray tip.

If the spray tip clogs while spraying, release the spray gun trigger, engage the trigger safety, shut off the pump, and follow the Pressure Relief Procedure

Warning on page 2.

Then proceed for your gun model:

Mode1217-593: Remove the spray tip and blow out the obstructions with air from the front of the spray tip, or

let

the spray tip and gun nozzle soak long enough to dissolve the obstruction. If it won't dissolve, jar it out by tapping the back of the spray tip against

a

flat surface.

Model 220-955: 307-848, supplied, for information on clearing a clog and cleaning the spray tip.

CAUTION

NEVER soak the entire gun in solvent. Prolonged exposure to solvent can ruin the packings.

1. Remove the screw 114) from the trigger guard retainer 113).

2. Push up on the trigger guard 112) and swing it away from the trigger 15).

3. Unscrew the gun handle from the fluid housing 126) and remove the filter. Clean the filter in compatible solvent.

4. Apply lithium-base grease to the threads of the fluid tube (191, and reassemble the gun.

Flushing the Gun

Before flushing,

WARNING

be sure'the entire system and flushing pails are properly grounded. Refer to

Grounding, on page 3.

Follow the Pressure

Relief Procedure on page 2, and remove the spray tip from the gun. Always use the lowest possible fluid pressure, and maintain firm metal to metal contact between the gun and the pail during flushing to reduce the risk of

a

fluid injection in- jury, static sparking and splashing.

Relieve pressure, remove the spray tip, and then flush the gun and spray system with a compatible solvent.

Always flush the gun before the fluid being sprayed can dry in it.

Cleaning the Filter 1171 See Fig 3.

Normal daily flushing of your spray system and gun flushes away most buildup on the filter. However, you

'should remove the filter weekly and clean it.

MAINTAIN FIRM

CONTACT BETWEEN

GUN AND CONTAINER

__

SERVICE

the skin, or injury from moving parts or electric

NOTE:

A repair kit, part no. 218-070, is available for repairing the gun. Use all new parts in the kit for the best results.

Parts included in the kit are shown with asterisks, for example (30"). two

Disassembly (See Parts Drawing, page 7)

1. Remove the tip guard (3), tip (8). and gasket (2).

2. Squeeze the trigger while unscrewing the dif- fuser/seat (1) and gasket (38). -

3. Remove the locknut (25) and end cap ( 2 3 ) .

4. Tap the rear of the gun with a plastic mallet to push the needle assembly out the front.

5. Unscrew the ball and housing (35) from the fluid needle (24). Remove the spring (34). gland (30). packing (291, O-ring (28). and washer (27).

6. Soak the parts in clean, compatible solvent. Wipe clean. Inspect for wear or damage and replace parts as needed.

Adjusting the Needle (See Fig 5)

WARNING

Proper adjustment of the needle is essential to be sure the trigger safety latch makes the gun in- operative when engaged. Improper adjustment may allow the gun to be triggered. even with the trigger safety latch engaged, resulting in serious bodily injury, including fluid injection and splashing in the eyes or on the skin.

1. Engage the gun safety latch.

2. Hold the gun with the nozzle straight up so the trig- ger falls onto the safety latch.

NOTE:

If the trigger does not touch the latch, turn the locknut (25) clockwise until it does.

3. With light pressure, hold the trigger against the latch. Turn the locknut 125) clockwise until there is enough tension for you to feel and see the trigger raise slightly off the latch.

4. Now turn the adjusting nut 3/4 turn counterclock- wise.

5. Connect the hose. Install the tip guard and prime the system. Trigger the gun and release it. The fluid flow should stop immediately. Now engage the safety latch and try to trigger the gun. No fluid should flow.

If the gun fails either test, relieve pressure, discon- nect the hose and readjust the needle.

Reassembly (See Parts Drawing, page 7)

1. Grease the O-ring (28"*) with lithium-based grease and install it in the groove of the packing (29"').

2. Install the washer (27**), packing and O-ring assem- bly, gland (30"") with stem facing small end of nee- dle, and the spring 134") on the needle (24**).

3. Screw on the ball and housing (35"') lightly, torqu- ing only to 6-10 in-lb (0.9-1.1 N m ) .

4. Guide the threaded end of the needle assembly into the front of the gun.

5. Install the end cap, aligning its guides with the holes in the rear of the gun. Install the locknut (25) loosely.

6. Squeeze the trigger while installing the gasket

138"') and diffuser/seat (1). Torque the diffuser seat to 20-25 ft-lb (27-34 N m ) .

TO ENGAGE SAFETY

LATCH, ION SAFE1 PULL

OUT LATCH AND TURN

TORIGHTANGLEWITH BODY

7. If the gun handle (6) was removed, screw it hand tight into the fluid housing (26). Loosen the setscrew (4), align the handle with the fluid housing, and torque the setscrew to 80-90 in-lb (9-10 N m ) .

6. Adjust the needle before using the gun. See Ad- justing the Needle.

9. Be sure the trigger guard and tip guard are installed before using the gun.

6

307-614

PARTS

DRAWING

REF NO. QTY REF NO. QN '13

Model

220-955.

Series A

Includes items 1.

4 t o 41

REF PART

NO. NO.

DESCRIPTION

QN

5

5a

6

10

11

12

13

14

1

2

3

4

15

16

17

17a

18

18a

19

20

21

*"218-023 DlFFUSERlSEAT 1

'166-969

GASKET. tip (used with flat tips only) 1

220-251 TIP GUARD 1

100-421 SETSCREW, soc hd cup pt;

5/16-18 x 318"

179-734 TRIGGER, 2

finger (standard1

179-943 TRIGGER, 4 finger (optional)

1

1

1

218-643 GUN HANDLE ASSEMBLY includes replaceable items 4,13 814

t172-479 TAG, instruction

t179-761 TAG, warning

179-724 GUARD, trigger

179-730

101-666

RETAINER, guard

SCREW, thread forming type "F";

8-32 x 5/16"

SWIVEL, gun 218021

179-750 RETAINER, spring

*z~am

(standard 50 mesh) includes replaceable items 16, 18,

20 Et

21

*218133

179-731

179-732

179-721

179-763

179-722

FLUID FILTER ASSEMBLY

(optional 100 mesh1 includes replaceable items 16, 18a 20 Et 21a

ELEMENT, strainer, (standard 50 mesh)

ELEMENT, strainer, (optional 1W mesh)

TUBE, fluid

SPRING, compression

RETAINER, spring (color coded blue),(for standard 60 mesh filter)

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

Model 217-593, Series C

includes items 1

to 39

REF PART

NO. NO.

DESCRIPTION

QN

21a

22

23

24

25

26

27

28

29

30

31

32

33

34

35

37

38

39

40

41

179-957

'179-733

179-720

.'218-022

**107-110

179-718

"179-762

RETAINER, spring (color coded orangeJ,lfor optional 100 mesh filter1

GASKET, sleeve

CAP, end

NEEDLE, fluid

LOCKNUT; no. 10-32 thread

HOUSING, fluid

WASHER, backup

"103-185 O-RING; polyurethane

"177-222

**I ..

.

105-334

PACKING, needle

-

LOCKNUT; M4 x 0.7 thread

177-538

179-737

"107-109

"218-024

STUD, trigger

PIN, actuator

SPRING, compression

BALL &HOUSING

179-729

**

156-766 t 179-960

'221-517

HOUSING, needle

GASKET, copper

CARD, warning

SPRAY TIP; 517 SwitchTipTM

=m-422

IV DripLess" Tip Guard

See 307-848, supplied

1

307 number in description refers to separate instruction manual.

*Recommended "tool box" spare parts. Keep on hand to reduce down time.

1

1

1

1

1

1

1

1

1

1

2

1

1

1

1

1

1

1

1

**.Supplied in repair kit 218-070 tExtra warning tags and cards are supplied at no charge.

307614 7

ACCESSORIES

(Must be purchased separately).

IN-LINE FILTER 210-742

5ocMpsi (350

60 mesh (250 micron) screen, standard replacement screen for 210-742.

210-731 Includes three 60 mesh (250 screens

210-732 Includes three 100 mesh (149 micron) screens

210-733 Includes three 200 mesh (74 micron) screens

SWIVELS

Use for more flexible gun movement.

207-946 112 npsm(f1 x318 npt(f)

5wo psi (350 bar) Max. Working Pressure

204-940 114 npt x 114 npsm

3dw psi (210 bar) Max. Working Pressure

IN-LINE FILTER 210-5M)

3wIl

(210 bar) MAXIMUM WORKING PRESSURE

Installs between gun and hose.

*

NYLON BRUSHES lOl-&l 0.375, ( 9 m m l dia.

101-892 0.625" (16 m m ) dia.

WRENCH 171-147

TECHNICAL DATA

Maximum working pressure : 3600 psi (252

Fluid orifice : 0.125 in. (3.18 mm)

Wetted parts : Stainless Steel, Aluminum,

Tungsten Carbide, Copper,

Polyurethane, Polyethylene,

Nylon

Weight : 20 (135 g)

Inlet : 114 npsmlm) swivel

SERVICE INFORMATION

Listed below by the assembly changed are the OLD,

NEW and ADDED parts.

.ASSEMBLY PART REF PART

Gun to

Series C

NEW

ADDED

3 212033 Guard

3 220-251 Guard

39 179-960 Card

NEW PRODUCT NOTE: Gun Model 220-955 has been added to this manual.

HOW TO ORDER REPLACEMENT PARTS

1. To be sure you receive the correct replacement parts, kit or accessories, always give requested in the chart below. all of the information

2. Check the parts list to identify the correct part number; do not use the ref. no. when ordering.

3. Order all parts from your nearest Graco distributor.

6 digit

PART

NUMBER QTY PART DESCRIPTION

THE GRACO WARRANTY AND DISCLAIMERS

WARRANTY

Graco warrants all Equipment manufactured by it and bearing its name to ba free from defects in material and workmanship on the data of sale by an authorized Graco distributor to the original purchaser for use. As purchaser's sola remedy for breach of this warranty, Graco will, for a period of twalva months from the data of sala, repair or replace any part of tha aquipmant proven defactiva. This warranty applies only when tha equipment is installad:operatad and maintained in accordance with Graw's written recommendations.

This warranty does not covar, and Graco shall not be liable for, any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance. negligence, accident, tamparing, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility with Graco equipment of structures, accessories, aquip- ment or materials not supplied by Graco, or the improper design, manufacture, installation, oparation or maintenance of structures, ac- c~ssonas, by Graco.

This warranty is conditioned upon tha prepaid return of the equipment claimed to be dafectiva for axamination by Graco to verify tha claimed defect. If tha claimed defect is verified, Graco m'll repair or replace free of charge any defective parts. The equipment m'li be returned to the original purchaser transporntion prepaid. If inswtion of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge. which charges may include tha the costs of parts, labor and transportation.

EQUIPMENT NOT COVERED BY GRACO WARRANTY

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PAR-

TICULAR PURPOSE, WITH RESPECT TO ACCESSORIES, EQUIPMENT, MATERIALS, OR COMPONENTS SOLD BUT NOT MANUFAC-

TURED BY GRACO. These itams sold, but not manufactured by Graco (such es alectric motor, switches, hose, atc.), ara subject to the warran-

N, any, of their manufacturer. Graco will provide purchaser with reasonable BIuistance in making any claim for breach of thaw warranties.

Factory Branches:Atlanta, Dallas, Detrolt,

Compani-:Canada;

Loa Angeler, West Caldwell IN.J.1

England: Switzerland: France; Germany: Hong Kong; Japan

GRACO INC. P. 0. Box 1441 MINNEAPOLIS, MN 55440-1444

PRINTEO IN U.S.A. ma14 581

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement