Graco 307614P Contractor Airless Spray Gun Owner's Manual

Add to my manuals
16 Pages

advertisement

Graco 307614P Contractor Airless Spray Gun Owner's Manual | Manualzz

INSTRUCTIONS-PARTS LIST

This manual contains important warnings and information.

READ AND KEEP FOR REFERENCE.

First choice when quality counts.

307–614

Rev. P

Supersedes N

INSTRUCTIONS

Contractor Airless Spray Gun

3600 psi (252 bar, 25.2 MPa) MAXIMUM WORKING PRESSURE

Model 220–955, Series D

Includes RAC DripLess Guard, 517 size

SwitchTip , and 2 finger trigger.

Four finger trigger is optional; see parts list.

Model 235–990, Series C

Includes the Standard (non-reversing) DripLess

Tip Guard and 4-finger trigger.

Spray tip not included. Order separately.

Model 217–593, Series E

Includes the Standard (non-reversing) DripLess

Tip Guard. Spray tip not included. Order separately.

Model 820–165, Series D

Includes RAC DripLess Guard, 517 size

SwitchTip , and 2 finger trigger.

Four finger trigger is optional; see parts list.

Models 220–955, 820–165

Patents Pending

Model 217–593

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

http://www.graco.com

COPYRIGHT 1983, GRACO INC.

Graco Inc. is registered to I.S. EN ISO 9001

Table of Contents

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation/Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . .

How to Use the Trigger Safety Latch . . . . . . . . . . . . .

How to Use the Gun . . . . . . . . . . . . . . . . . . . . . . . . . . .

How to Adjust the Spray Pattern

How to Clean the Spray Tip

. . . . . . . . . . . . . . . . . . and Clear a Spray Tip Obstruction . . . . . . . . . . . .

5

5

2

5

6

6

How to Clean the Filter

Service

. . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts Drawing

Parts List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12

13

8

9

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Graco Phone Numbers

Warranty

. . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15

15

16

7

Symbols

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to or destruction of equipment if you do not follow the instructions.

FIRE AND EXPLOSION HAZARD

Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and result in a fire or explosion and serious injury.

If there is any static sparking or you feel an electric shock while using this equipment, stop

spraying immediately. Do not use the equipment until you identify and correct the problem.

Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid being sprayed.

Keep the spray area free of debris, including solvent, rags, and gasoline.

Electrically disconnect all equipment in the spray area.

Extinguish all open flames or pilot lights in the spray area.

Do not smoke in the spray area.

Do not turn on or off any light switch in the spray area while operating or if fumes are present.

Do not operate a gasoline engine in the spray area.

Ground the equipment and the object being sprayed. See Grounding on page 5.

INJECTION HAZARD

Spray from the gun, leaks or ruptured components can inject fluid into your body and cause extremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also cause serious injury.

Fluid injected into the skin is a serious injury. The injury may look like just a cut, but it is a serious injury. Get immediate medical attention.

Do not point the gun at anyone or at any part of the body.

Do not put your hand or fingers over the spray tip.

Do not stop or deflect leaks with your hand, body, glove or rag.

Do not “blow back” fluid; this is not an air spray system.

Always have the tip guard and the trigger guard on the gun when spraying.

Check the gun diffuser operation weekly. Refer to the gun manual.

Be sure the gun trigger safety operates before spraying.

Lock the gun trigger safety when you stop spraying.

Follow the Pressure Relief Procedure on page 5 if the spray tip clogs and before cleaning, checking or servicing the equipment.

Tighten all fluid connections before operating the equipment.

Check the hoses, tubes, and couplings daily. Replace worn or damaged parts immediately. Do not repair high pressure couplings; you must replace the entire hose.

Fluid hoses must have spring guards on both ends, to help protect them from rupture caused by kinks or bends near the couplings.

TOXIC FLUID HAZARD

Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin, inhaled, or swallowed.

Know the specific hazards of the fluid you are using.

Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local, state and national guidelines.

Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and solvent manufacturer.

RECOIL HAZARD

Due to the high pressure fluid emitted, a strong recoil action may occur when you trigger this gun. If you are unprepared, your hand could be forced back toward your body or you could lose your balance and fall, resulting in serious injury.

INSTRUCTIONS

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.

This equipment is for professional use only.

Read all instruction manuals, tags, and labels before operating the equipment.

Use the equipment only for its intended purpose. If you are uncertain about usage, call your

Graco distributor.

Do not alter or modify this equipment.

Check equipment daily. Repair or replace worn or damaged parts immediately.

Do not exceed the maximum working pressure of the lowest rated system component. Refer to the Technical Data on page 15 for the maximum working pressure of this equipment.

Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the

Technical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.

Do not use 1,1,1–trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents in pressurized aluminum equipment. Such use could result in a chemical reaction, with the possibility of explosion.

Do not use hoses to pull equipment.

Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose Graco hoses to temperatures above 82 C (180 F) or below –40 C (–40 F).

Do not lift pressurized equipment.

Comply with all applicable local, state, and national fire, electrical, and safety regulations.

Wear ear protection when operating this equipment.

Installation/Operation

System Requirements

WARNING

Keep the wallet-sized warning card provided with this gun with the operator at all times. The card contains important treatment information should an injection injury occur. Additional cards are available at no charge from Graco Inc.

WARNING

Be sure your system has a bleed-type master air valve (pneumatic pumps only) and a pressure drain valve. These accessories help reduce the risk of serious bodily injury, including fluid injection, splashing in the eyes or on the skin, or injury from moving parts, if you are adjusting or repairing the pump or gun.

1. The bleed-type master air valve (air-powered pumps only) relieves air trapped between this valve and the pump after the air regulator is shut off. Trapped air can cause the pump to cycle unexpectedly.

2. The pressure drain valve assists in relieving fluid pressure in the displacement pump, hose and gun: triggering the gun to relieve pressure may not be sufficient.

3. Strain the fluid you are spraying if it contains particles which could clog the spray tip.

Grounding

To reduce the risk of static sparking, ground the sprayer and all other spray equipment used or located in the spray area. Check your local electrical code for detailed grounding instructions for your area and type of equipment.

WARNING

INJECTION HAZARD

The system pressure must be manually relieved to prevent the system from starting or spraying accidentally. Fluid under high pressure can be injected through the skin and cause serious injury. To reduce the risk of an injury from injection, splashing fluid, or moving parts, follow the Pressure Relief Procedure whenever you: are instructed to relieve the pressure, stop spraying, check or service any of the system equipment, or install or clean the spray tip.

Pressure Relief Procedure

1. Engage the gun safety latch.

2. Turn the ON/OFF switch to OFF.

3. Unplug the power supply cord.

4. Disengage the gun safety latch. Hold a metal part of the gun firmly to a grounded metal pail. Trigger the gun to relieve pressure.

5. Engage the gun safety latch.

6. Open the system pressure drain valve. Leave the pressure drain valve open until you are ready to spray again.

If you suspect that the spray tip or hose is completely clogged, or that pressure has not been fully relieved after following the steps above, VERY SLOWLY loosen the tip guard retaining nut or hose end coupling to relieve pressure gradually, then loosen completely.

Now clear the tip or hose obstruction.

How to Use the Gun Trigger Safety

1. To engage the gun trigger safety, turn the latch to a right angle with the gun body. See Fig. 1.

2. To disengage the gun trigger safety, push the latch out and turn it parallel with the gun body.

ENGAGED

Fig. 1

DISENGAGED

307-614 5

Installation/Operation

How to Use the Gun

1. Connect a grounded fluid hose to the gun inlet.

See Fig. 2

7. If adjusting the pressure does not give a good spray pattern, follow the Pressure Relief Proce-

dure on page 5 and then try another tip size.

2. With no tip installed, start the pump. Flush the pump according to the instructions supplied with it.

Prime the system with the fluid.

3. Follow the Pressure Relief Procedure on page 5. Be sure the gun trigger safety is locked.

See Fig. 1.

8. Use a full-open, full-close triggering action. Hold the gun about 14 in. (350 mm) from and at right angles to the work surface. Don’t swing the gun in an arc. Practice to find the best length and speed of stroke.

How to Adjust the Spray Pattern

4. Models 217–593 & 235–990: unscrew the tip guard

(3) and install the tip (A) and the gasket (2) in the nut of the tip guard. Screw the assembly firmly onto the gun. Tighten the assembly with a wrench.

See Fig. 2.

1. To adjust the spray pattern direction, follow the

Pressure Relief Procedure on page 5. Loosen the tip guard retaining nut (B). Turn the tip guard/ tip groove horizontally (C) for a horizontal pattern and vertically (A) for a vertical pattern. Tighten the nut.

NOTE: If the gasket (2) is not installed, the gun will leak.

5. Models 220–955 and 820–165: install the

SwitchTip (40) and the tip guard (41). See manual

307–848, supplied. See Fig. 2.

2. The spray tip orifice and spray angle determines the coverage and size of pattern. When more coverage is needed, use a larger spray tip rather than increasing fluid pressure.

41

CAUTION

The openings in the tip guard reduce paint buildup on the tip guard while spraying. Any damage to the sharp edges of the openings causes paint to collect at that area. Never hang the gun by the tip guard.

40

KEY

A Tip guard shown in position for vertical spray pattern

B Retaining nut

C Tip guard shown in position for horizontal spray pattern

B

C

A

2

Fig. 2

3

6. Start the pump. Adjust the fluid pressure until the spray is completely atomized. Use the lowest pressure necessary to get the desired results.

Higher pressure may not improve the spray pattern and will cause premature tip wear and pump wear.

Fig. 3

A

Installation/Operation

How to Clean the Spray Tip and Clear a Spray Tip Obstruction

2. Remove the spray tip and blow out the obstruction by applying air to the front of the spray tip. Or, let the spray tip and gun nozzle soak to dissolve the obstruction. If it won’t dissolve, jar it out by tapping the back of the spray tip against a flat surface.

WARNING

To reduce the risk of fluid injection or splashing in the eyes or on the skin, do not hold a hand, body or rag in front of the spray tip when cleaning or checking a clogged tip. Point the gun toward the ground or into a waste container when checking to see if the spray tip is cleared.

DO NOT try to “blow back” paint; this is NOT an air spray gun.

DO NOT wipe fluid buildup off the gun or spray tip until pressure is relieved.

Gun 220–955 & 820–165 – with RAC guard

1. Lock the gun trigger safety. Rotate the RAC guard handle 180 . See Fig. 4.

2. Unlock the gun trigger safety. Trigger the gun into a pail or onto the ground to remove the clog.

Cleaning during the day.

3. Lock the gun trigger safety. Rotate the tip handle to the spraying position.

1. Follow Pressure Relief Procedure on page 5.

2. Clean the front of the tip frequently during the day to help reduce buildup. Also clean the tip and tip guard at the end of each work day. Use a solventsoaked brush to clean the spray tip.

4. If the tip is still clogged, lock the gun trigger safety, shut off the sprayer and disconnect the power source, and open the pressure drain valve to relieve pressure. Clean the spray tip as shown in manual 307–848, supplied with the RAC guard.

Clearing an obstruction.

If the spray tip clogs while spraying, immediately stop spraying, then:

Gun 217–593 & 235–990 – with standard tip guard

1. Lock the gun trigger safety, open the pressure drain valve.

A

CAUTION

Never soak the entire gun in solvent. Prolonged exposure to solvent can ruin the packings.

KEY

A Handle shown in spraying position. Turn handle

180 and trigger gun to clear clog.

Fig. 4

7659A

Installation/Operation

How to Check the Gun Diffuser Operation

Check the diffuser operation weekly. The gun diffuser/ seat (A) breaks up spray and reduces the risk of fluid injection when the tip is not installed. Perform the test below. If it fails, replace the entire Needle Kit, Part No.

218–070, as instructed on page 7. Diffuser/seats are not sold separately since the gun will leak if an old needle is used with a new diffuser/seat.

5. Apply lithium-base grease to the threads of the fluid tube (19) and reassemble the gun.

A

1. Follow Pressure Relief Procedure on page 5.

2. Remove the tip guard and spray tip.

3. Start the sprayer and adjust it to the lowest

pressure.

4. Aim the gun into a grounded metal pail while holding it firmly to the pail. Trigger the gun. If the fluid emitted is not diffused into an irregular stream, replace the entire needle kit immediately.

See Fig. 5.

How to Clean the Filter (

See Fig. 6.)

Normal daily system flushing removes most buildup on the filter (17). For a weekly cleaning:

1. Follow Pressure Relief Procedure on page 5.

2. Remove the screw (14).

3. Push up on the trigger guard (12) and swing it away from the trigger (5).

4. Unscrew the gun handle from the housing (26).

Remove the filter and clean it in compatible solvent.

Fig. 5

5

12

Fig. 6

26

14

19

8 307-614

Installation/Operation

How to Flush the Gun

WARNING

ÄÄ

To reduce the risk of serious bodily injury, including splashing fluid in the eyes or on the skin, or static electric discharge when flushing:

Be sure the entire system, including flushing pails, are properly grounded.

Remove the tip guard and spray tip.

Maintain metal to metal contact between the gun and the flushing pail.

Use the lowest possible pressure.

Always flush the pump and the gun before the fluid being sprayed can dry in it.

NOTE: If it is available, the flushing procedure provided in your pump or sprayer manual should be used instead of this procedure.

1. Follow Pressure Relief Procedure on page 5.

2. Remove the tip guard and spray tip. Soak and clean the parts.

3. Put the pump intake in a grounded pail of water or solvent.

4. Start the pump at its lowest pressure.

5. Trigger the gun into the original pail. When solvent appears, release the trigger.

6. Now trigger the gun into the solvent pail. Circulate the fluid until the system is thoroughly flushed.

7. Follow Pressure Relief Procedure on page 5.

307-614 9

1 A

B

C

1

Torque to 20-25 ft-lb

(27-34 N.m)

2

Fig. 7

Torque to 80–90 in-lb

(9–10 N.m)

23

D

Service

4. If the gun handle (6) was removed, hand tighten it into the fluid housing (26); it should fit easily. Only if necessary, loosen the setscrew (4), align the handle with the fluid housing and torque the setscrew to 80–90 in-lb (9–10 N.m).

4

2

5. Adjust the needle before using the gun. Procedure below.

01706

6. Be sure the trigger guard and tip guard are installed before using the gun.

Adjusting the needle

(See Fig 8)

1. Engage the gun safety latch.

2. Hold the gun with the nozzle straight up so the trigger falls onto the safety latch.

NOTE: The needle (C), diffuser/seat (A), gasket (B) and locknut (D) must be replaced together. They are included in Kit 218–070.

Disassembly

(See Fig 7 )

1. Follow the Pressure Relief Procedure on page

5.

2. Remove the tip guard assembly. See Fig 2.

3. Squeeze the trigger while unscrewing the diffuser/ seat (A) and gasket (B).

3. With light pressure, hold the trigger against the latch. Turn the locknut (D) clockwise until there is enough tension for you to feel and see the trigger raise slightly off the latch.

4. Turn the adjusting nut 3/4 turn counterclockwise.

5. Connect the fluid hose. Install the tip guard and prime the system. Trigger the gun and release it.

The fluid flow should stop immediately. Engage the safety latch and try to trigger the gun. No fluid should flow. If the gun fails either test, relieve pressure, disconnect the hose and readjust the needle.

4. Remove the locknut (D) and end cap (23).

1

5. Tap the rear of the gun with a plastic mallet to push the needle assembly out the front.

Reassembly

(See Fig 7)

1. Guide the threaded end of the needle assembly into the front of the gun.

D

2

2. Install the end cap, aligning its guides with the holes in the rear of the gun. Install the locknut (D) loosely.

3. Squeeze the trigger while installing the gasket (B) and diffuser/seat (A). Torque the diffuser seat to

20–25 ft-lb (27–34 N.m).

1

2

Fig 8

Engage trigger safety latch

Arrows indicate clockwise turn

01705

Notes

Model 220–955, Series D

Includes items 1 and 4 to 41

Model 235–990, Series C

Includes items 1 to 39

Model 217–593, Series E

Includes items 1 to 39

Model 820–165, Series D

Includes items 1 to 39

Parts Drawing

1

32

26

23

Included with 1

33

31

22

21

41

40

3

2

37

12

Purchase separately

4

5

6

13

14

15

18

19

20

16

10

11

12

13

14

15

16

17

Parts List

Model 220–955, Series D; Model 235–990, Series C; Model 217–593, Series E; Model 820–165, Series D

Ref.

No.

1

2

3

4

5

5a

6

17a

18

18a

Part No.

Description

218–070 NEEDLE–DIFFUSER/SEAT KIT

166–969 GASKET, tip (used with flat tips only)

220–251 TIP GUARD

100–421 SETSCREW , soc hd, 5/16–18 x 3/8”

179–734 2 FINGER TRIGGER (standard)

179–943 4 FINGER TRIGGER

(Model 235–990 only)

218–643 GUN HANDLE ASSEMBLY includes replaceable items 4, 13, 14

172–479 INSTRUCTION TAG

179–761 WARNING TAG

190–972 TRIGGER GUARD

179–730 GUARD RETAINER

109–575 SCREW , 8–32 x 5/16”

218–021 SWIVEL

179–750 SPRING RETAINER

218–131 FLUID FILTER ASSEMBLY

(standard 50 mesh) includes replaceable items 16, 18, 20, 21

218–133 FLUID FILTER ASSEMBLY

(optional 100 mesh) includes replaceable items 16, 18a, 20, 21a

179–731 STRAINER ELEMENT

(standard 50 mesh)

179–732 STRAINER ELEMENT

(optional 100 mesh)

Qty.

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

22

23

26

31

32

33

37

39

40

41

Ref.

No.

19

20

21

21a

Part No.

Description Qty.

179–721 FLUID TUBE

179–763 SPRING

179–722 SPRING RETAINER (color coded blue)

(for standard 50 mesh filter)

179–957 SPRING RETAINER (color coded orange)

1

179–733

191–244

(for optional 100 mesh filter)

GASKET

END CAP

1

1

1

179–718 FLUID HOUSING

105–334 LOCKNUT; M4 x 0.7 thread

177–538 TRIGGER STUD

179–737 ACTUATOR PIN

179–729 NEEDLE HOUSING

222–385 WARNING CARD (not shown)

221–517 SWITCHTIP SPRAY TIP, SZ 517

1

1

1

1

1

1

2

1

1

237–859 RAC DripLess GUARD

See manual 307–644 for parts 1

Replacement Danger and Warning labels, tags and cards are available at no cost.

Keep these spare parts on hand to reduce down time.

Accessories

SWIVELS and WHIP HOSES FILTERS

3000 psi (210 bar, 21 MPa)

Maximum Working Pressure.

Adequate filtering is important for a good surface finish and to minimize tip clogging. These filters provide secondary filtering. Elements are available in various mesh sizes.

Swivels and whip hoses provide more flexible gun movement for easier handling and less fatigue.

Working pressures are listed in the descriptions.

214–925 Swivel, 1/4 npsm x 3/8 npt(f)

5000 psi (350 bar, 35 MPa)

Max. Working Pressure

Mounts in hose

207–946 Swivel, 1/2 npsm x 3/8 npt(f)

5000 psi (350 bar, 35 MPa)

Max. Working Pressure

213–068 Includes filter body, spring and one

100 mesh screen.

213–069 Includes filter spring and one

60 mesh screen.

Use with above filter body.

210–742 Includes filter spring and one

100 mesh screen.

Use with above filter body.

210–729 Includes assembly 213–068 plus a

3 ft (0.9 m) whip hose for more flexible gun movement.

Standard filter elements

204–940 Swivel, 1/4 npt x 1/4 npsm

3000 psi (210 bar, 21 MPa)

Max. Working Pressure

214–701 Whip hose, nylon, coupled 1/4 npsm(f) x 3/8 npt(m), spring guards both ends.

3000 psi (210 bar, 21 MPa)

Max. Working Pressure

TIP GUARDS

224–455 Two, 50 mesh filters (179–731)

224–456 Two, 100 mesh filters (179–732)

Mounts between hose and gun

These tip guards fit all Graco airless spray guns.

Choose the one that’s right for your application. One of these tip guards is included with every Graco airless gun.

210–500 Includes swivel, adapter and one

60 mesh screen

Replacement elements for above filters

237–859 Performance Series Reverse–A–Clean

DripLess t Guard.

Order SwitchTip separately.

See your distributor for available sizes.

210–731 Three 60 mesh (250 micron) screens

210–732 Three 100 mesh (149 micron) screens

210–733 Three 200 mesh (74 micron) screens

TOOLS

Nylon Brushes

Use to thoroughly clean the gun’s fluid passages.

101–891

101–892

0.375” (9 mm) dia.

0.625” (16 mm) dia.

220–251 Standard DripLess t Tip Guard. Order flat tip separately. See your distributor for available sizes.

Wrench 171–147

Fits all hexes on the gun.

222–674 Heavy Duty RAC R DripLess t Tip Guard.

Order SwitchTip separately. See your distributor for available sizes.

Technical Data

Maximum Working Pressure

Fluid Orifice Size

. . . . . . . . . . . . . . 3600 psi

(252 bar, 25.2 MPa)

. . . . . . . . . . . . . . . 0.125 in. (3.18 mm)

Wetted Parts

Weight

. . . . . . . . . Stainless steel, Polyethylene,

Polyurethane, Nylon,

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PTFE

18 oz. (510 g)

Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maximum Material Temperature

1/4 npsm(m)swivel

. . . . . . . . 120 F(50 C)

Sound Data

Sound Pressure Level

Sound Power Level

. . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . .

78 dB(A)*

87 dB(A)*

* Measured while spraying waterbase paint – gravity

1.36 through a 517 tip at 3,000 psi (207 bar).

Per ISO 3744

PTFE

Graco Phone

Number

TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to you: 1–800–328–0211 Toll Free.

Manual Change

Summary

Changed Revision level of manual from N to P.

307-614 15

Graco Warranty

Graco warrants all equipment listed in this manual which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. With the exception of any special extended or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of

Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance or structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT

NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, gas engines, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

LIMITATION OF LIABILITY

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

ADDITIONAL WARRANTY COVERAGE

Graco does provide extended warranty and wear warranty for products described in the “Graco Contractor Equipment W arranty

Program”.

All information, illustrations and specifications in this document are based on the latest product information available at the time of publication. The right is reserved to make changes at any time without notice.

Sales Offices: Atlanta, Chicago, Detroit, Los Angeles

Foreign Offices: Belgium, Canada, England, Korea, Switzerland, France, Germany, Hong Kong, Japan

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

http://www.graco.com

PRINTED IN U.S.A. 307–614 May 1983, Revised August 1997

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement