Graco 307713B PRESSURE ROLLER EQUIPMENT Owner's Manual

Add to my manuals
4 Pages

advertisement

Graco 307713B PRESSURE ROLLER EQUIPMENT Owner's Manual | Manualzz
INSTRUCTIONS-PARTS LIST (3 207713
Rev B
This manuel contains IMPORTANT GRACO SUPERSEDES A
WARNINGS and INSTRUCTIONS
READ AND RETAIN FOR REFERENCE
PRESSURE ROLLER EQUIPMENT
300 psi (21 bar) MAXIMUM WORKING PRESSURE
Operate your pump at the lowest pressure needed for sufficient paint supply to roller
Adjustable Extension Roller Kit 218-625
Includes Roller Frame, 18-36 in. Extension Tube,
3/8 in. nap Roller Cover and 45° Gun Adapter
Y ны ae : De AS
Adjustable Extension Tubes if A A ee
LA г Lover
218-775 18-36 in. (0.45-0.9 m) NN, Rolle A Ñ
218-776 3-6 ft (0.9-1.8 m) > NS
218-777 6-12 ft (1.8-3.7 m) Ne [Roller Frame
218-778 8-16 ft (2.4-4.8 m) (See manual
7-755 f
*45° Gun Adapter 218-932 arte)
1/4 npt(m) x 7/8 UNF(F)
*Flush Kit 218-944
Uses standard garden hose to flush water-base
paints from the Extension Tube and Roller Frame
*360° Straight Swivel 218-931
1/4 npt x 1/4 npsmif) swivel
*Gun Adapter Kits for non-Graco guns
218-945 For guns with 3/4-20 nozzle Graco Inline
threads (Binks) Dispensin
218-946 For guns with 1-1/16-16 nozzle Valve
threads (Wagner)
Tip Gaskets 218-600
Package of 5 tip gaskets
Adjustable
Extension
Tube
*See packaging for specific installation
instructions
NOTE: For a leak-free connection,
use pipe sealant on all male threads.
360° Straight
Swivel
45° Gun Adapter
Graco Gun Tip Gasket
| Flush Kit
GRACO INC. P.O. Box 1441 MINNEAPOLIS, MN 55440-1444
©COPYRIGHT 1985, GRACO INC.
WARNING
Be sure all operators of this equipment read, understand, and follow the warnings and instructions
in the manuals for all painting equipment and this manual.
AVOID POWER LINES un ne DO NOT OVERPRESSURIZE THIS EQUIPMENT
Avoid contact with any power lines! Contact with Operate your pump at the lowest pressure needed for
power lines could cause extremely serious bodily injury, sufficient paint supply to the roller. The pressure is safer
including burns or electrocution. at lower pressures, and the paint is easier to control.
PRESSURE RELIEF PROCEDURE = ~— fe Use the Adjustable Extension Tube ONLY with the
Roller Frame described in this manual. THIS IS NOT AN
To reduce the risk of serious bodily injury from fluid in- AIRLESS GUN EXTENSION (pole gun)! Do not attempt
jection, splashing in the eyes, injury from moving parts to modify the tube or roller frame or to use parts which
or property damage, always follow this procedure are not designed to be used with this equipment. Modi-
whenever you stop painting, and before checking, fying parts can cause them to over-pressurize which can
changing or repairing any part of the paint system. result in component rupture or explosion, and cause
serious bodily injury, including fluid injection, and
1. Engage the gun safety latch. splashing in the eyes, or property damage.
2. Shut off the power to the pump.
3. Open the fluid drain valve (required in your system to If at any time while you are using the Adjustable Exten-
help relieve pressure). sion Tube, the extension tube starts to extend, stop roll-
4. Disengage the gun safety latch and trigger the gun. ing immediately and engage the gun safety latch. Check
5. Engage the gun safety latch. to be sure the locknut on the tube is tight. If it is, then
the tube or roller is clogged; follow the Pressure Relief
This pressure relief procedure may be different than the Procedure, then flush the system thoroughly.
one supplied with your pump or paint gun. Use this pro-
cedure ONLY when using this Pressure Roller Equip-
ment. At other times, relieve the pressure exactly as
stated in your separate pump or paint gun instruction
manual.
ELECTRICAL GROUNDING о
To reduce the risk of static sparking which can cause and follow all grounding instructions in your separate
fire or explosion and result in serious bodily injury and pump and paint gun instruction manual, and follow all
property damage, be sure your entire system and the local codes regarding electrical grounding.
object you are painting are properly grounded. Read
ADJUSTABLE EXTENSION TUBES …
218-775 18-36” (460-920 mm)
218-776 3-6’ (0.92-1.8 m)
218-777 6-12' (1.8-3.7 m)
218-778 8-16’ (2.4-4.8 m)
SCREW
Includes replaceable item 108-163, shaft seal. APPLY LOCKTITE \_
NOTE: Always flush the extension tube as LEE )
instructed in Flushing on page 3. HANDLE LEE
Wetted parts : Stainless Steel, Polyurethane,
Plated Steel LD Lo
SEAL
LIPS OF SEAL (4) MUST FACE INTO
TUBE (1): GREASE BEFORE ASSEMBLY;
DO NOT DAMAGE LIPS
WASHER
RING
y] 307-713
ADJUSTABLE EXTENSION ROLLER KIT 218-625 :
installation
1. Assemble the roller kit as shown in Fig 2. Be sure
the gasket is in place between the gun and adapter.
2. Extend the tube to the desired length and tighten
the locknut nut securely.
NOTE: Always allow cold equipment to warm to
room temperature before using.
Operation
1. Be sure the fluid drain valve is closed and the gun
safety latch is engaged. Then start the pump and
set it to the lowest possible operating pressure.
2. Disengage the gun safety latch and trigger the gun
briefly until paint comes to the roller.
3. Experiment with triggering and rolling the paint un-
til you determine just how often you need to trigger
the gun to keep an even flow of paint to the rolier.
4. Increase the pump pressure only if you cannot get a
sufficient supply of paint to the roller.
5. To adjust the extension tube while painting, engage
the gun safety latch. Loosen the locknut and ex-
tend or retract the tube. If retracting, some paint in
the tube will be pushed out to the roller. Either roll
this excess paint onto the wall, or completely re-
tract the tube, drain the excess paint into a pail,
then adjust the tube length. Tighten the locknut
securely.
6. Whenever you stop painting, follow the
PRESSURE RELIEF PROCEDURE on page 2.
Then elevate the roller end of the tube to prevent
paint from draining.
7. Flush the pump, gun and extension tube im-
mediately after each use to prevent paint from dry-
ing in the equipment and damaging it. See
Flushing, below.
NOTE: A Flush Kit, Part No. 218-944, can be used
to flush water-base paint from the Extension
Tube and Roller Frame. Instructions are on
the kit package.
Flushing
To flush the pump, gun, extension tube and roller frame
without disconnecting parts, use the following
procedure.
1. Follow the PRESSURE RELIEF PROCEDURE
WARNING on page 2.
2. Remove the roller cover. Refer to the back page.
3. Fully extend the extension tube and tighten the
locknut securely. This is very important to
thoroughly flush the tube.
4. Prepare the pump for flushing as instructed in your
separate pump instruction manual. Use a solvent
that is compatible with the paint you are using.
5. Point the extension tube and roller frame away from
yourself or any other person. Then turn on the
pump and flush the system thoroughly as described
in your separate pump instruction manual, using
the lowest pressure possible. While flushing, loosen
the extension tube locknut and pump the tube in
and out several times.
Model 218-625,
Includes items 1-5
REF PART DESCRIPTION QTY
NO. NO.
1
218-935 FRAME, roller
See manual 307-755 for
parts
2 218-775 EXTENSION TUBE,
18-36” (460-920 mm) 1
3 218-929 ADAPTER 45°, 1/4
npt(m) x 7/8 UNF(F) 1
4 166-969 GASKET 1
5 107-590 COVER, 1/2” nap 1
COVER (5)
|
EXTENSION TUBE (2)
la
GASKET (4) |
|. ADAPTER (3)
Fig 2
WARNING
Always keep your hands and body away from the
roller frame when flushing. High pressure fluid
emitted from the holes in the frame could cause
an injection injury.
Shut off the pump and follow the PRESSURE
RELIEF PROCEDURE WARNING on page 2.
Never leave water in the pump, gun or extension
tube: doing so will cause corrosion. After flushing
with water, flush again with solvent or mineral
spirits, and relieve pressure. This leaves a coating of
solvent or mineral spirits in the system. Retract the
extension tube before storing it.
Clean the roller cover thoroughly before storing it.
307-713 3
HOW TO ORDER REPLACEMENT PARTS
1. To be sure you receive the correct replacement parts,
kit or accessories, always give all of the information
requested in the chart below.
2. Check the parts list to identify the correct part number;
do not use the ref. no. when ordering.
3. Order all parts from your nearest Graco distributor.
6 digit
PART
NUMBER QTY | PART DESCRIPTION
THE GRACO WARRANTY AND DISCLAIMERS
WARRANTY
Graco warrants all equipment manufactured by it and bearing its name to be free from defects in material and workmanship on the date of sale
by an authorized Graco distributor to the original purchaser for use. As purchaser's sole remedy for breach of this warranty, Graco will, for a
period of twelve months from the date of sale, repair or replace any part of the equipment proven defective. This warranty applies only when the
equipment is installed, operated and maintained in accordance with Graco's written recommendations.
This warranty does not cover, and Graco shall not be liable for, any malfunction, damage or wear caused by faulty installation, misapplication,
abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor
shall Graco be liable for malfunction, damage or wear caused by the incompatibility with Graco equipment of structures, accessories, equip-
ment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, ac-
cessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective for examination by Graco to verify the claimed
defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the
original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be
made at a reasonable charge, which charges may include the the costs of parts, labor and transportation.
DISCLAIMERS AND LIMITATIONS
THE TERMS OF THIS WARRANTY CONSTITUTE PURCHASER'S SOLE AND EXCLUSIVE REMEDY AND ARE IN LIEU OF ANY OTHER
WARRANTIES (EXPRESS OR IMPLIED), INCLUDING WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PAR-
TICULAR PURPOSE, AND OF ANY NON-CONTRACTUAL LIABILITIES, INCLUDING PRODUCT LIABILITIES, BASED ON NEGLIGENCE OR
STRICT LIABILITY. EVERY FORM OF LIABILITY FOR DIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES OR LOSS IS EXPRESSLY EX-
CLUDED AND DENIED. IN NO CASE SHALL GRACO’S LIABILITY EXCEED THE AMOUNT OF THE PURCHASE PRICE. ANY ACTION FOR
BREACH OF WARRANTY MUST BE BROUGHT WITHIN TWO (2) YEARS OF THE DATE OF SALE.
EQUIPMENT NOT COVERED BY GRACO WARRANTY
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PAR-
TICULAR PURPOSE, WITH RESPECT TO ACCESSORIES, EQUIPMENT, MATERIALS, OR COMPONENTS SOLD BUT NOT MANUFAC-
TURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motor, switches, hose, etc.), are subject to the warran-
ty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.
Factory Branches:Atlanta, Dallas, Detroit, Los Angeles, West Caldwell (N.J.)
Subsidiary and Affiliate Companies:Canada; England; Switzerland; France; Germany; Hong Kong; Japan
GRACO INC. P.O. Box 1441 MINNEAPOLIS, MN 55440-1444
PRINTED IN U.S.A. 307-713 2-85 Revised 10-85

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement