Graco 308461D AA Plaus Air-Assisted Airless Spray Package Owner's Manual

Add to my manuals
16 Pages

advertisement

Graco 308461D AA Plaus Air-Assisted Airless Spray Package Owner's Manual | Manualzz

INSTRUCTIONS-PARTS LIST

This manual contains important warnings and information.

READ AND KEEP FOR REFERENCE.

First choice when quality counts.

308–461

Rev. D

Supersedes B and PCN D

INSTRUCTIONS

30:1 PRESIDENT STAINLESS STEEL, WALL MOUNT

AA Plus Air-Assisted Airless

Spray Package

See the Data Sheet, 305–664, for application information

3000 psi (21.0 MPa, 210 bar) Maximum System Working Pressure

100 psi (0.69 MPa, 6.9 bar) Maximum Air Inlet Pressure

Model 237–422, Series A

This complete package includes a pump, an AA Plus air-assisted airless spray gun with a 411 spray tip, wall bracket, 25 ft. (7.6 m) air and fluid hoses, air and fluid controls, and a fluid feed.

IMPORTANT

This manual provides the basic safety, installation, and operation information for the package. For your safety, also read the component manuals supplied with this package before operating it.

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

http://www.graco.com

COPYRIGHT 1994, GRACO INC.

Graco Inc. is registered to I.S. EN ISO 9001

Table of Contents

Symbols

Warnings

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Ground the System . . . . . . . . . . . . . . . . . . . . . . . . .

System Component Information

Operation

. . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Pressure Relief Procedure

Flushing

. . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9

11

8

9

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Technical Data

Warranty

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Graco Phone Number . . . . . . . . . . . . . . . . . . . . . . . . . .

12

14

16

16

6

7

2

3

Symbols

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to or destruction of equipment if you do not follow the corresponding instructions.

WARNING

INJECTION HAZARD

Spray from the gun, hose leaks, or ruptured components can inject fluid into your body and cause extremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also cause serious injury.

Fluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate medical attention.

Do not point the gun at anyone or at any part of the body.

Do not put your hand or fingers over the spray tip.

Do not stop or deflect leaks with your hand, body, glove or rag.

Do not “blow back” fluid; this is not an air spray system.

Always have the tip guard and the trigger guard on the gun when spraying.

Check the gun diffuser operation weekly. Refer to the gun manual.

Be sure the gun trigger safety operates before spraying.

Lock the gun trigger safety when you stop spraying.

Follow the Pressure Relief Procedure on page 9 whenever you: are instructed to relieve pressure; stop spraying; clean, check, or service the equipment; and install or clean the spray tip.

Tighten all fluid connections before operating the equipment.

Check the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately.

Permanently coupled hoses cannot be repaired; replace the entire hose.

Use only Graco approved hoses. Do not remove any spring guard that is used to help protect the hose from rupture caused by kinks or bends near the couplings.

TOXIC FLUID HAZARD

Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin, inhaled, or swallowed.

Know the specific hazards of the fluid you are using.

Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local, state and national guidelines.

Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and solvent manufacturer.

WARNING

FIRE AND EXPLOSION HAZARD

Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and result in a fire or explosion and serious injury.

Ground the equipment and the object being sprayed. Refer to Ground the System on page 7.

If there is any static sparking or you feel an electric shock while using this equipment, stop spray-

ing immediately. Do not use the equipment until you identify and correct the problem.

Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid being sprayed.

Keep the spray area free of debris, including solvent, rags, and gasoline.

Electrically disconnect all equipment in the spray area.

Extinguish all open flames or pilot lights in the spray area.

Do not smoke in the spray area.

Do not turn on or off any light switch in the spray area while operating or if fumes are present.

Do not operate a gasoline engine in the spray area.

INSTRUCTIONS

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.

This equipment is for professional use only.

Read all instruction manuals, tags, and labels before operating the equipment.

Use the equipment only for its intended purpose. If you are uncertain about usage, call your Graco distributor.

Do not alter or modify this equipment. Use only genuine Graco parts and accessories.

Check equipment daily. Repair or replace worn or damaged parts immediately.

Do not exceed 3000 psi (21.0 MPa, 210 bar) maximum working pressure at 100 psi (0.69 MPa,

6.9 bar) maximum incoming air pressure of the pump, or the maximum working pressure of any accessory used with it.

Do not move or lift pressurized equipment.

Comply with all applicable local, state, and national fire, electrical, and safety regulations.

MOVING PARTS HAZARD

Moving parts, such as the air motor piston, can pinch or amputate your fingers.

Keep clear of all moving parts when starting or operating the pump.

Before servicing the equipment, follow the Pressure Relief Procedure on page 9 to prevent the equipment from starting unexpectedly.

Notes

308-461 5

Setup

CAUTION

This equipment is compatible with most water-based materials. See the wetted parts in the Technical

Data section and your solvent manufacturer’s compatibility information.

3. Bring an air line from you compressed air supply to the pump location. Be sure the air is dry and filtered. Install a bleed-type master air valve (A) upstream from the pump. Another master air valve

(15) is supplied with the package. When the bleedtype master air valve is closed and the pump air regulator (8a) is opened, the valve relieves all air pressure to the system.

I.

Prepare the Operator

All persons who operate the system should be trained in the safe, efficient operation of all system components as well as the proper handling of the chemical coating. At a minimum, all operators should thoroughly read the safety, installation, and operation sections of this manual and the component manuals.

4. Have a grounded, metal waste-container available to use when draining the filter.

5. Ventilate the spray booth.

II. Prepare the Site

WARNING

To prevent hazardous concentrations of toxic and/or flammable vapors, spray only in a properly ventilated spray booth. Never operate the spray gun unless ventilation fans are operating.

1. Use a minimum recommended 5 HP (3.7 kW) air compressor for efficient operation.

2. Clear obstacles and debris that could hinder the operator’s movement.

3, 4

A

B

Check and follow all of the national, state, and local codes regarding air exhaust velocity requirements.

KEY

Components you must supply:

A Bleed-type master air valve

Required for pump; order part no. 107–142, 1/4” npt(f)

B Air filter. Order part no.

106–149, 1/2 npt(f)

C Air supply line

D Grounded 5 gallon metal pail

E Air line moisture trap

Components supplied with package:

1 30:1 President pump

3 Air-assisted airless spray gun

4 Spray tip

5 Fluid filter

6 Gun fluid hose

7 Gun air hose

8a Pump air regulator

8b Gun air regulator

14 Bleed–type air valve

30 Pump ground wire

E

1

C 30

8b

8a

6

7

D

14

5

Fig. 1

III. Unpack the System

1. In addition to the assembled components, the air and fluid hoses, gun, and instruction manuals are packaged separately in the main shipping container. These are the manuals you should receive.

Setup

V. Connect the Hoses and Gun to the

System (See Fig. 1)

1. Connect the blue fluid hose (6) between the fluid filter and the fluid inlet of the spray gun (3). These are 1/4–18 npsm(f) swivel fittings.

308–106

308–640

307–273

308–167

306–861

30:1 Ratio President Pump

Air-assisted airless spray gun

Fluid Filter

Air Regulator

Ball Valve

2. Connect the red air hose (7) between the gun air regulator (8b) and the air inlet of the spray gun (3).

These are 1/4–18 npsm(f) swivel fittings.

IV. Setup the System

1. Be sure the wall where you plan to mount the wall bracket can support the weight of the system and the stress caused during pump operation.

3. Verify that all fittings throughout the system are tightened securely.

V. Ground the System

2. Remove the paper backing from the mounting template, supplied, Apply the template to the wall,

4 to 5 feet (1.2 to 1.6 m) above the floor. Drill the holes. The bolt holes are 0.48 inches (12 mm) in diameter. Remove the template. Mount the pump securely.

3. Thread the swivel elbow (20) onto the pump intake valve. Tighten securely. See Fig. 2.

WARNING

To reduce the risk of static sparking, ground the pump and all other equipment used or located in the spray area. Check your local electrical code for detailed grounding instructions for your area and type of equipment. Ground all of this equipment.

Also read FIRE AND EXPLOSION HAZARD on page 4.

Fig. 2

20

Pump: one end of the ground wire (30) is already connected to the air motor grounding lug. Connect the clamp end of the ground wire to a true earth ground.

Air and fluid hoses: use only electrically conductive hoses with a maximum of 500 feet (150 m) combined hose length to ensure grounding continuity.

Air compressor: according to manufacturer’s recommendations.

Spray gun: grounding is obtained through connection to properly grounded fluid hoses and pump.

Fluid supply container: according to local code.

All solvent pails used when flushing, according to local code. Use only metal pails, which are conductive. Do not place the pail on a non-conductive surface, such as paper or cardboard, which interrupts the grounding continuity.

308-461 7

I.

System Component Information

How to Use the Air-Assisted Airless

Spray Gun

II.

How to Change the Spray Pattern

Direction

1. Relieve the air and fluid pressure.

With an air-assisted airless spray gun, the spray tip shapes the fluid into a fan pattern. Air from the air cap further atomizes the fluid and completes the atomization of the paint tails into the patterns to produce a more uniform pattern.

2. Install a spray tip in the gun. Rotate the air cap

(the spray tip rotates with it) to determine the direction of the spray pattern. See Fig. 4.

Vertical Spray Pattern Horizontal Spray Pattern

The spray gun has a built-in lead and lag operation.

When triggered, the gun emits air before the fluid is discharged. When the trigger is released, the fluid stops before the air flow stops. This helps assure the spray is atomized and prevents fluid buildup on the air cap.

NOTE: The gun air and fluid inlets have 1/4–18 npsm

(R1/4–19) compound male threads that are compatible with NPSM and BSP female swivel connectors.

1. The fan pattern valve (E) can be used to reduce the pattern by about 25% of the total pattern width.

As the valve is opened, the pattern will reduce slightly. The tip used designates the total width of the spray pattern.

Fig. 4

III.

How to Adjust the Air Regulators

(See Fig. 5)

0791

As you look at the system, the air regulator (8a) on the left regulates air to the gun and the air regulator (8b) on the right regulates air to the pump.

1. Always open air regulators slowly to prevent surging during startup.

2. To unlock the gun trigger safety, turn the safety so it is parallel with the trigger. To lock the gun trigger safety, turn the safety to a right angle with the trigger. See Fig. 3.

2. To open the regulator, which allows air to flow, turn the T-handle IN (clockwise). Turn the T-handle

OUT (counterclockwise) to close off the air flow.

Be sure the jam nut under the T-handle does not interfere with your adjustments. Tighten the jam nut to lock in the setting, if desired.

1

2

UNLOCKED gun trigger safety

LOCKED gun trigger safety

E

1

2

8a

8b

Fig. 3

0795A

Fig. 5

CCW

CW

04094

I.

Pressure Relief Procedure

WARNING

INJECTION HAZARD

Fluid under high pressure can be injected through the skin and cause serious injury. To reduce the risk of an injury from injection, splashing fluid, or moving parts, follow the Pressure Relief Procedure whenever you: are instructed to relieve the pressure, stop spraying, check or service any of the system equipment, or install or clean the spray tip.

Operation

If you suspect that the spray tip or hose is completely clogged or that pressure has not been fully relieved, very slowly loosen the tip retaining nut or hose end coupling and relieve pressure gradually. Clean the tip or hose obstruction.

II.

Flush the Pump Before First Use

Flush with a solvent compatible to your fluid. Consult the fluid manufacturer’s literature for recommendations. See Flushing on page 11.

III.

Prime the System (See Fig. 6)

1. Remove the air cap and spray tip from the gun.

2. Close the filter drain valve (26).

1. Lock the gun trigger safety.

3. Put the suction tube into the fluid supply container.

4. Make sure the air regulators (8a, 8b) are closed.

2. Close the bleed-type master air valves (A, 14).

3. Close the air regulators (8a, 8b).

5. Open the master air valves (A, 14).

NOTE: In the next steps, the pump will cycle quickly until air is purged.

4. Unlock the gun trigger safety.

6. Slowly turn on the pump air regulator (8a) until the pump cycles slowly.

5. Hold a metal part of the gun firmly against a grounded metal waste pail. Trigger the gun to relieve pressure.

6. Lock the gun trigger safety.

7. Open the filter drain valve (26), having a container ready to catch the drainage. Close the drain valve.

A

3

7. Hold a metal part of the gun firmly to the side of a grounded metal waste container. Trigger the gun while increasing pressure at the pump air regulator

(8a) just enough to purge the air and storage solvent from the system. When new fluid comes from the gun, release the trigger. Lock the gun trigger safety.

KEY

A Bleed-type master air valve

3 Air-assisted airless spray gun

8a Pump air regulator

8b Gun air regulator

14 Bleed–type air valve

26 Filter drain valve

8b

8a

14

26

Fig. 6

308-461 9

Operation

IV.

Set the Fluid and Air Pressure

1. Install the spray tip and air cap on the gun.

2. Adjust the pump air pressure regulator until the pressure shown on the fluid filter gauge is about

900 psi (6.3 MPa, 63 bar). This should require approximately 30 psi (210 kPa, 2.1 bar) air pressure to the pump.

3. Test spray a pass or stationary horizontal pattern.

Hold the gun 10 to 12 in. (250 to 300 mm) from the paper. Stripes in the outer edges of the pass or spots at the ends of the stationary pattern are likely at this point.

V.

WARNING

This system has a maximum air working pressure of 100 psi (690 kPa, 6.9 bar) which produces a maximum fluid working pressure of 3000 psi (21.0

MPa, 210 bar). Higher pressure can cause the system to rupture or malfunction and result in serious injury.

You are Now Ready For Production

Spraying

NOTE: If there are no stripes or spots, lower the fluid pressure until they appear before turning on the air to the gun.

4. Partially trigger the gun so only air is emitted. Set the gun air regulator to 20 psi (140 kPa, 1.4 bar).

5. Retest the spray pattern. Trigger the gun and adjust the gun’s air control valve (C) to add air to the aircap and to eliminate stripes or spots. If there are no stripes or spots, you are ready to start spraying.

6. If there are stripes or spots in the spray pattern, raise the pump air pressure until you raise the fluid outlet pressure by about 100 psi (690 kPa, 6.9 bar) and try again. Continue to raise the fluid pressure in 100 psi (690 kPa, 6.9 bar) increments until the pattern is full and clean. Do not exceed 100 psi

(690 kPa, 6.9 bar) incoming air pressure or 3000 psi (21.0 MPa, 210 bar) fluid working pressure.

CAUTION

When using catalyzed fluids, observe the pot life as recommended by the fluid manufacturer. Always flush the system before the pot life has expired to prevent dried fluid which may be difficult to clean out and may damage the system.

VI.

When to Shut Down the System

WARNING

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the

Pressure Relief Procedure on page 9.

NOTE: Always use the lowest fluid and air pressure required for good atomization and spray pattern for maximum fluid efficiency. Air pressure over approximately 30 psi (210 kPa, 2.1 bar) will cause turbulence in the fan pattern, dirty air caps, and slower production capability.

Shut down the system at the end of the work shift and before checking, adjusting, cleaning, or repairing the system. Always relieve the pressure.

I.

When to Flush

Before the first time use.

II.

When changing colors.

Before fluid can dry or settle out in a dormant system (observe the recommended fluid pot life on catalyzed fluids).

Before storing the system.

How to Flush (See Fig. 7)

WARNING

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the

Pressure Relief Procedure on page 9.

1.

Relieve the pressure.

Flushing

NOTE: The gun air regulator (8b) always stays closed during flushing.

2. Remove the air cap and spray tip before flushing.

3. Remove the air cap and spray tip from the gun and clean separately. Do not reinstall at this time.

4. Unscrew the fluid filter (5) bowl. Remove the screen. See manual 307–273. Reinstall the bowl without the screen.

5. Put the suction tube into a grounded metal pail with about 1/2 gallon (2 liters) of a compatible solvent.

6. Make sure the air regulators (8a, 8b) are closed.

A

3

7. Open the master air valves (A, 14).

8. Slowly turn on the pump air regulator (8a) until the pump cycles slowly.

9. Hold a metal part of the gun firmly against the grounded metal waste container. Trigger the gun.

Slowly increase the pump air regulator setting until the fluid flows freely. (Some air will spit from the gun until the fluid arrives.)

10. Keeping the gun triggered, decrease the pump air regulator (8a) pressure as much as possible without stalling the pump, and pump out the solvent until air comes through the gun.

11. Repeat the procedure with clean solvent, if needed.

12. Release the trigger and lock the gun trigger safety.

13. Close the master air valves (A, 14). Fully close the pump air regulator (8a).

14. Open the drain valve (26), having a container ready to catch the drainage.

15. Remove the suction hose from the solvent and place it in an empty container.

16. Clean the filter screen, air cap and spray tip separately. Reinstall the filter screen.

17. Thoroughly clean the inside and outside of the suction tube.

KEY

A Bleed-type master air valve

3 Air-assisted airless spray gun

5 Fluid filter

8a Pump air regulator

8b Gun air regulator

14 Bleed–type air valve

26 Filter drain valve

8b

8a

14

26

5

Fig. 7

Model 237–422, Series A

Includes items 1 to 43

15

5

Parts

30

1

23 25

16

17

8

33

27

34

9

29

26

14

13

12

27

3,4

33

9

8

10

7

6

20

18

19

28

2

27

43

11

21

22

32

31

Parts

1

2

3

4

5

6

Model 237–422, Series A

Includes items 1 to 34, 42

Ref

No.

Part No.

Description

7

8

9

10

11

12

13

14

15

16

Qty

223–843 PRESIDENT PUMP

See manual 308–106 for parts

186–727 WALL MOUNTING BRACKET

238–852 AIR ASSISTED AIRLESS SPRAY GUN

See manual 308–640 for parts

GG4–411 SPRAY TIP, 0.011 orifice,

1

1

1

1 8–10” (203–254 mm) fan width

223–160 FLUID FILTER

See manual 307–273 for parts

236–074 FLUID HOSE, cpld 1/4 npt(fbe)

3/16” ID x 25’ (4.8 mm ID x 7.6 m)

210–867 AIR HOSE, cpld 1/4 npsm(fbe)

1/4” ID x 25’ (6.3 mm ID x 7.6 m)

1

1

1

104–267 AIR REGULATOR

0–125 psi (0–0.9 MPa, 0–9 bar) range

See manual 308–167 for parts

101–180 AIR PRESSURE GAUGE

0–200 psi (0–1.4 MPa, 0–14 bar)

155–470 90 SWIVEL ADAPTER UNION,

1/2 npt(f)

112–941 FLUID PRESSURE GAUGE

166–999 ELBOW, reducing street,

1/2 npt(m) x 1/4 npt(f)

2

2

1/2 npt(m) x 1/2 npsm(f) swivel

218–093 AIR HOSE, buna-S, cpld 1/2 npt(mbe)

1/2” ID x 22” (13 mm ID x 559 mm)

222–297 45 SWIVEL ADAPTER UNION,

1

1

1/2 npt(m) x 1/2 npsm(f) swivel 1

158–491 NIPPLE, 1/2 npt, 1.625” (41 mm) long 1

107–142 BLEED-TYPE AIR VALVE,

1

1

1

27

28

29

30

Ref

No.

17

18

43

31

32

33

34

42

19

20

21

22

23

24

25

26

Part No.

Description

162–453 NIPPLE, 1/2 npt x 1/4 npsm

236–076 SUCTION HOSE, 3/4 npt(mbe),

3/4” ID x 6’ (19 mm x 1.82 m)

188–867 SUCTION TUBE, 3/4 npt(f)

112–192 FLUID INTAKE ELBOW, 3/4 npt(f)

100–016 LOCKWASHER, 1/4” spring

100–270 SCREW

235–208 SWIVEL UNION,

3/8 npt(n) x 3/8 npsm(f)

206–994 THROAT SEAL LIQUID, 8 oz.

188–089 NIPPLE, 3/8 npt x 3/8–18.6 sf

235–992 BALL VALVE, 3/8 npt x 1/4 npt(mbe)

See manual 306–861 for parts

156–877 NIPPLE, 1/2 npt, 2/5” (63.5 mm)

188–595 PUMP MOUNTING PLATE

102–254 SCREW, hex hd, 1/4–20 x

7/8” (22 mm) long

237–569 GROUND WIRE and CLAMP

12 gauge (1.5 mm 2 ), 25’ (7.6 m)

100–220 THUMBSCREW, 5/16–18 unc,

1” (25 mm) long

188–940 BUNG ADAPTER

100–509 PLUG, 1/4 npt sq hd pipe

179–749 AIR MANIFOLD, 1/2 npt inlet, two 1/2 npt outlets

290–037 MOUNTING TEMPLATE

(not shown)

157–416 90 SWIVEL UNION

Qty

1

2

1

1

1

1

1

1

1

1

1

2

1

3

1

1

2

1

1

2

Technical Data

Category

Maximum Fluid Working Pressure

Maximum Air Operating Pressure

Pump Air Consumption – free flow

Gun Air Consumption

Pump Wetted Parts

Gun Wetted Parts

Fluid Filter Wetted Parts

Fluid Fittings Wetted Parts

Fluid Hose Wetted Parts

Data

3000 psi (21.0 MPa, 210 bar)

100 psi (0.69 MPa, 6.9 bar)

20 scfm at 100 psi (0.56 m 3 /min at 0.69 MPa, 6.9 bar)

5 scfm at 30 psi (0.14 m 3 /min at 210 kPa, 2.1 bar)

304/316//420/17–PH stainless steel, chrome plating, tungsten carbide, PTFE, leather, UHMWPE

303 stainless steel, carbide, UHMWPE CV75, polyethylene,

PTFE, Delrin

303/304/316 stainless steel, polyethylene, PTFE

304/316 stainless steel nylon

All 304, 316, and 17–4 PH SST are electropolished and/or passivated. Delrin is a registered trademark of the

Company

Manual Change Summary

This manual was revised to include the changes from

PCN D.

Notes

308-461 15

Graco Standard Warranty

Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of

Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT

NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.

Graco Phone Numbers

TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to you:

1–800–367–4023 Toll Free.

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Sales Offices: Minneapolis, Detroit, Los Angeles

Foreign Offices: Belgium, Canada, England, Korea, France, Germany, Hong Kong, Japan

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

http://www.graco.com

PRINTED IN U.S.A. 307–929 December 1988, Revised November 1997

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement