Graco 307879M 15:1 RATIO FIRE-BALL Undercoater Pumps Owner's Manual | Manualzz
INSTRUCTIONS-PARTS LIST
307–879
Rev. M
Supersedes Rev. J
First choice when
and PCN K
quality counts.
Includes Rev. L
This manual contains important
warnings and information.
READ AND KEEP FOR REFERENCE.
INSTRUCTIONS
15:1 RATIO FIRE-BALL
Undercoater Pumps
2250 psi (16 MPa, 157 bar) Maximum Fluid Working Pressure
180 psi (1.2 MPa, 12 bar) Maximum Incoming Air Pressure
Portable and stationary units for filled undercoating materials.
Dispense
Kit
Cover
Model No.
Size, Type
222–077
35 lb, portable
X
X
226–342
120 lb, rollaround
X
X
226–268
120 lb, rollaround
X
X
226–343
120 lb, rollaround
X
X
226–269
400 lb, stationary
X
X
231–384
120 lb, rollaround
X
X
231–385
400 lb, stationary
X
X
WARNING
These systems are designed to be used only
in pumping petroleum-based undercoating
materials. Any other use of the system can cause
unsafe operating conditions and result in
component rupture, fire, or explosion, which can
cause serious bodily injury, including fluid injection.
Model 226–268
7303A
GRACO INC.
P.O. BOX 1441 MINNEAPOLIS, MN
COPYRIGHT 1988, GRACO INC.
Graco Inc. is registered to I.S. EN ISO 9001
55440–1441
Table of Contents
Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Parts Drawings and Lists
Model 222–077, 35-lb Pail Size Unit . . . . . . . . . . .
Dispense Kit 222–079 . . . . . . . . . . . . . . . . . . . . . . .
Model 226–342, 120-lb Drum Size Unit
with Dolly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model 226–384, 120-lb Drum Size Unit
with Dolly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model 226–268, 120-lb Drum Size Unit
with Portable Base . . . . . . . . . . . . . . . . . . . . . . . . . .
2
307–879
10
10
11
11
12
Parts Drawings and Lists (continued)
Model 231–385, 400-lb Stationary Drum
Size Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dispense Kit 237–889 . . . . . . . . . . . . . . . . . . . . . . .
Model 226–269, 400-lb Stationary Drum
Size Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dispense Kit 222–082 . . . . . . . . . . . . . . . . . . . . . . .
Model 226–343, 120-lb Drum Size Unit
with Portable Base . . . . . . . . . . . . . . . . . . . . . . . . . .
Dispense Kit 222–357 . . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Graco Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Graco Phone Number . . . . . . . . . . . . . . . . . . . . . . . .
13
13
13
13
14
14
15
16
16
Notes
307–879
3
Symbols
Warning Symbol
Caution Symbol
WARNING
CAUTION
This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.
This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.
WARNING
INJECTION HAZARD
Spray from the gun, hose leaks, or ruptured components can inject fluid into your body and cause an
extremely serious injury, including the need for amputation. Splashing fluid in the eyes or on the skin
can also cause a serious injury.
Fluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate medical attention.
Do not point the dispensing valve at anyone or at any part of the body.
Do not put hand or fingers over the spray tip.
Do not stop or deflect fluid leaks with your hand, body, glove, or rag.
Do not “blow back” fluid; this is not an air spray system.
Always have the tip guard and the trigger guard on the gun when spraying.
Be sure the gun trigger safety operates before spraying.
Lock the gun/valve trigger safety when you stop spraying.
Follow the Pressure Relief Procedure on page 8 whenever you: are instructed to relieve pressure; stop spraying; clean, check, or service the equipment; and install or clean the spray tip.
Tighten all the fluid connections before operating the equipment.
Check the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately.
Permanently coupled hoses cannot be repaired; replace the entire hose.
TOXIC FLUID HAZARD
Hazardous fluids or toxic fumes can cause a serious injury or death if splashed in the eyes or on the
skin, swallowed, or inhaled.
Know the specific hazards of the fluid you are using. Read the fluid manufacturer’s warnings.
Store hazardous fluid in an approved container. Dispose of the hazardous fluid according to all
local, state, and national guidelines.
Wear appropriate protective clothing, gloves, eyewear, and respirator.
4
307–879
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor air ventilation, open flames, or sparks can cause a hazardous condition and
result in fire or explosion and serious injury.
Ground the equipment and the object being sprayed. See Grounding on page 6.
Provide fresh air ventilation to avoid the buildup of flammable fumes from solvent or the fluid being
sprayed.
Extinguish all the open flames or pilot lights in the spray area.
Electrically disconnect all the equipment in the spray area.
Keep the spray area free of debris, including solvent, rags, and gasoline.
Do not turn on or off any light switch in the spray area while operating or if fumes are present.
Do not smoke in the spray area.
Do not operate a gasoline engine in the spray area.
If there is any static sparking while using the equipment, stop spraying immediately. Identify and
correct the problem.
EQUIPMENT MISUSE HAZARD
INSTRUCTIONS
Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly and result
in a serious injury.
This equipment is for professional use only.
Read all the instruction manuals, tags, and labels before operating the equipment.
Use the equipment only for its intended purpose. If you are uncertain about usage, call your Graco
distributor.
Do not alter or modify this equipment. Use only genuine Graco parts and accessories.
Check the equipment daily. Repair or replace worn or damaged parts immediately.
The maximum working pressure of the 15:1 Ratio Fire-Ball pumps is 2250 psi (16 MPa, 157 bar)
at a maximum air operating pressure of 180 psi (1.2 MPa, 12 bar). Never operate the pump at a
higher air or fluid working pressure. Do not exceed the maximum working pressure of the lowest
rated system component.
Use fluids that are compatible with the equipment wetted parts. See the Technical Data section of
all the equipment manuals. Read the fluid manufacturer’s warnings.
Route the hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not
expose Graco hoses to temperatures above 180F (82C) or below –40F (–40C).
Do not use the hoses to pull equipment.
Wear hearing protection when operating this equipment.
Comply with all applicable local, state, and national fire, electrical, and other safety regulations.
United States Government safety standards have been adopted under the Occupational Safety and Health Act. You
should consult these standards––particularly General Standards, Part 1910, and Construction Standards, Part
1926.
307–879
5
Installation
Grounding
WARNING
FIRE AND EXPLOSION HAZARD
Before operating, ground the system as
explained below. Also read the section
FIRE AND EXPLOSION HAZARD on
page 5.
Fluid hoses: Use only electrically conductive hoses
with a maximum of 500 feet (150 m) combined
hose length to ensure grounding continuity.
Spray gun: Obtain grounding through connection to
a properly grounded fluid hose and sprayer or
pump.
Supply container: Follow the local code.
Static electricity is created by the flow of fluid through
the pump and hose. If the pump is not properly
grounded, sparking may occur, and the system may
become hazardous. Sparking may also occur when
plugging in or unplugging a power supply cord. Sparks
can ignite fumes from solvents, dust particles and
other flammable substances, whether you are
operating indoors or outdoors, and can cause a fire or
explosion and serious bodily injury and property
damage.
To reduce the risk of static sparking, ground all the
dispensing equipment used or located in the work
area. Check you local electrical code for detailed
grounding instructions for your are and type of
equipment. Be sure to ground all of this equipment.
Pump or sprayer: If using an electric sprayer, plug
the power supply cord or extension cord, each
equipped with an undamaged three-prong plug, into
a properly grounded outlet. Do not use an adapter.
All extension cords must have three wires and be
rated for 15 amps. If using another type of sprayer
or pump, ground it by connecting a grounding wire
(12 ga minimum) from the pump or sprayer’s
grounding lug to a true earth ground.
Object being sprayed: Follow the local code.
All solvent pails used when flushing: Follow the
local code. Use only metal pails, which are
conductive. Do not place the pail on a
non-conductive surface, such as paper or
cardboard, which interrupts the grounding
continuity.
To maintain grounding continuity when flushing or
relieving pressure, always hold a metal part of the
gun firmly to the side of a grounded metal pail, then
trigger the gun.
To ground the pump, loosen the grounding lug
locknut (W) and washer (X). Insert one end of a
12 ga (1.5 mm2) minimum ground wire (Y) into the
slot (Z) in the lug, and tighten the locknut securely.
Connect the other end of the wire to a true earth
ground. To order a ground wire and clamp, order
Part No. 222–011.
Z
Y
Air compressor or hydraulic power supply: Follow
the local code.
6
307–879
X
W
Installation
Assembling the Unit
Air Line and Accessories
Refer to the appropriate parts drawing on pages
10 through 14 to assemble your unit. Use thread
sealant on all male connections, except at swivels.
NOTE: Install the air line accessories in the order
shown in the Typical Installation drawing. See page
15 to order the accessories.
The spray gun supplied with these units includes an
open style tip guard. For spraying undercoating
materials, remove that guard and use the
Reverse-A-Clean IV tip guard and tip, also
supplied.
1. Install a pump runaway valve (G) to shut off the air
to the pump if the pump accelerates beyond the
pre-adjusted setting. A pump that runs too fast can
be seriously damaged.
For Models 222–077 & 226–269: Remove the cover
from the supply drum and install the pump and
cover. Tighten the cover thumbscrews.
For Model 226–342 only: Assemble the dolly. Place
the opened drum on the dolly. Tighten the nut onto
the carriage bolt to secure the drum.
For Models 226–268 & 226–343: Assemble the
portable base. Place the opened drum on the base.
Tighten the thumbnut against the clamp to secure
the drum.
Typical Installation
2. Install an air line lubricator (F) for automatic air
motor lubrication.
3. Install the air regulator (C) to control pump speed
and pressure.
4. On the main air supply line from the compressor,
install an air line filter (E) to remove harmful dirt
and contaminants from your compressed air
supply.
CAUTION
Do not hang air accessories directly on the air inlet.
The fittings are not strong enough to support accessories and may cause one or more to break. Provide
a bracket on which to mount accessories.
D
J
G
E
C
NOTE: This typical installation is only a guide
for selecting and installing a system; it is not an
actual system design. Contact your Graco
distributor for assistance in designing a system
to suit your needs.
F
B
H
KEY
A
A
B
C
D
E
F
G
H
J
Fluid dispense line
Pump ground wire
Air regulator
Main air supply line
Air filter
Pump lubricator
Pump runaway valve
Fluid drain valve
Bleed-type master air valve
7308A
307–879
7
Operation
Pressure Relief Procedure
WARNING
INJECTION HAZARD
Fluid under high pressure can be injected through the skin and cause serious injury. To reduce the risk of an injury
from injection, splashing fluid, or moving parts, follow the Pressure Relief Procedure whenever you
Are instructed to relieve the pressure
Stop spraying
Check or service any of the system equipment
Install or clean the spray tips
1. Engage the gun safety latch.
2. Shut off the power supply to the pump and open
any air bleed valves in the system.
3. Disengage the gun safety latch.
8
307–879
4. Hold a metal part of the gun firmly to the side of a
grounded metal pail, and trigger the gun to relieve
pressure.
5. Engage the gun safety latch.
6. Open the fluid drain valve, and have a container
ready to catch the drainage.
7. Leave the drain valve open until you are ready to
use the system again.
If you suspect that the gun, hose, or spray tip is
completely clogged, or that pressure has not been fully
relieved after following the steps above, very slowly
loosen the tip guard retaining nut, outlet accessory nut,
or hose end coupling, and relieve pressure gradually,
then loosen completely, then clear the tip or hose.
Operation
Start-up: Single or Multiple Pump Systems
1. Close the air regulators and bleed-type master air
valves to all but one pump.
2. Open the master air valve from the compressor.
3. For the pump that is connected, trigger the
dispensing valve into a grounded metal waste
container, making firm metal-to-metal contact
between the container and valve. Open the
bleed-type master air valve and open the pump air
regulator slowly, just until the pump is running.
When the pump is primed and all air has been
pushed out of the lines, release the trigger.
4. If you have more than one pump, repeat this
procedure for each pump.
6. If your pump accelerates quickly, or is running too
fast, stop it immediately and check the fluid supply.
If the supply container is empty and air has been
pumped into the lines, prime the pump and lines
with fluid, or flush it and leave it filled with a
compatible solvent. Be sure to eliminate all air
from the fluid system.
CAUTION
Never allow the pump to run dry of the fluid being
pumped. A dry pump quickly accelerates to a high
speed, possibly damaging itself, and it may get
very hot.
NOTE: When the pump is primed, and with sufficient
air supplied, the pump starts when the dispensing
valve is opened and shuts off when it is closed.
NOTE: A pump runaway valve can be installed on the
air line to automatically shut off the pump if it starts to
run too fast. See Accessories, page 15.
5. Set the air pressure to each pump at the lowest
pressure needed to get the desired results.
7. Read and follow the instructions supplied with
each component in your system.
WARNING
The maximum working pressure of each pump in
your system may not be the same. To reduce the
risk of over-pressurizing any part of your system,
be sure you know the maximum working pressure
rating of each pump and its connected components. Never exceed the maximum working pressure of the lowest rated component connected to a
particular pump.
8. Whenever you shut off the system, always follow
the Pressure Relief Procedure.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure at left.
To determine the fluid output pressure using the air
regulator reading, multiply the ratio of the pump by
the air pressure shown on the regulator gauge. For
example:
10:(1) ratio x 100 psi air =1000 psi fluid output
[10:(1) ratio x 7 bar air = 70 bar fluid output]
[10:(1) ratio x 0.7 MPa air = 7 MPa fluid output]
Limit the air to the pump so that no air line or fluid
line component or accessory is over-pressurized.
307–879
9
Parts
Model 222–077
Dispense Kit 222–079
35-lb Pail Size Unit
Ref
No.
Part No.
Description
101
109–075
102
103
106
107
108
208–536
204–940
156–971
109–165
210–890
109
110
111
156–849
104–984
210–657
112
113
100–940
169–971
AIR REGULATOR;
See 307–204 for parts.
COUPLER, quick disconnect
SWIVEL; See 306–861 for parts.
NIPPLE, 1/4 npt
HOSE, fluid, cpld
SPRAY GUN;
See 307–260 for parts.
NIPPLE, 3/8 npt
TEE, pipe; 1/4 npt
BALL VALVE;
See 306–861 for parts.
ELBOW, street; 1/4 npt
FITTING, pin
Ref
No. Part No.
Description
1
206–405
2
222–079
3
3a
3b
3c
3d
222–058
206–522
100–220
100–916
100–922
Qty
PUMP, 15:1 Ratio Fire-ball;
See 306–531 for parts.
DISPENSE KIT;
See Parts List at right.
COVER; Includes items 3a to 3d
COVER, pail
THUMBSCREW
LOCKWASHER
CAPSCREW
1
1
1
1
1
3
2
2
Qty
112
111
107
109
101
106
113
102
110
3d
3c
108
103
3a
3b
7304A
10
307–879
1
1
1
1
1
1
1
1
1
1
1
Parts
Model 226–342
Model 231–384
120-lb Drum Size Unit with Dolly
120-lb Drum Size Unit with Dolly
Ref
No. Part No.
1
206–699
2
222–079
3
4
204–574
204–144
4a
4b
4c
4d
4e
100–023
100–307
101–851
102–971
205–419
Description
Ref
No. Part No.
Qty
PUMP, 15:1 Ratio Fire-ball;
See 306–531 for parts.
DISPENSE KIT;
See Parts List on page 10.
COVER; See 306–345 for parts.
BASE, dolly;
Includes items 4a to 4d
WASHER, flat; 5/16”
NUT, full hex; 3/8–16
CASTER, wheel, 2 1/2” dia.
BOLT, carriage; 3/8–16 x 3”
CLAMP, dolly
1
206–699
2
237–889
3
4
204–574
204–144
4a
4b
4c
4d
4e
100–023
100–307
101–851
102–971
205–419
1
1
1
1
1
1
4
1
1
Description
Qty
PUMP, 15:1 Ratio Fire-ball;
See 306–531 for parts.
DISPENSE KIT;
See Parts List on page 13.
COVER; See 306–345 for parts.
BASE, dolly;
Includes items 4a to 4d
WASHER, flat; 5/16”
NUT, full hex; 3/8–16
CASTER, wheel, 2 1/2” dia.
BOLT, carriage; 3/8–16 x 3”
CLAMP, dolly
1
1
1
1
1
1
4
1
1
1
3
Part No.
220–955
from
Dispense Kit
237–889
2
Part No.
210–890
from
Dispense Kit
222–079
4e
4c
4b
4a
4d
7307A
307–879
11
Parts
Model 226–268
120-lb Drum Size Unit with Portable Base
Ref
No. Part No.
Description
1
206–699
2
222–079
3
4
204–574
203–622
4a
4b
4c
4d
4e
4f
4g
191–750
802–275
191–747
100–214
100–132
113–660
113–646
Qty
PUMP, 15:1 Ratio Fire-ball;
See 306–531 for parts.
DISPENSE KIT;
See Parts List on page 10.
COVER; See 306–345 for parts.
BASE, portable
Contains 4a to 4g
BASE, drum
BOLT, hex hd; 5/16”–18 x 1.5”
BRACKET
WASHER, lock
WASHER, flat
RIVET
CASTER; polyurethane
1
1
1
1
1
2
2
2
2
16
4
3
2
See page 10 for
Dispense Kit
parts.
4b
4d
4e
4c
4a
4f
7303A
4g
7303A
12
307–879
Parts
Model 231–385
Model 226–269
400-lb Stationary Drum Size Unit
400-lb Stationary Drum Size Unit
Ref
No. Part No.
1
2
2
Description
206–700
200–326
237–889
Ref
No. Part No.
Qty
PUMP, 15:1 Ratio Fire-ball;
See 306–531 for parts.
COVER; drum
DISPENSE KIT;
See Parts List below.
1
206–700
1
1
2
222–082
1
3
200–326
Dispense Kit 237–889
Part No.
Description
101
109–075
AIR REGULATOR;
See 307–204 for parts.
COUPLER, quick disconnect
SWIVEL; See 306–861 for parts.
HOSE, fluid, cpld
SPRAY GUN;
See 307–614 for parts.
FITTING, pin
208–536
204–940
214–703
220–955
113
169–971
Qty
PUMP, 15:1 Ratio Fire-ball;
See 306–531 for parts.
DISPENSE KIT;
See Parts List below.
COVER; drum
1
1
1
Dispense Kit 222–082
Ref
No.
102
103
107
108
Description
Qty
1
1
1
1
1
1
1
112
Ref
No.
Part No.
Description
101
109–075
102
103
106
107
108
208–536
204–940
156–971
109–167
210–890
109
110
111
156–849
104–984
210–657
112
113
100–840
169–971
AIR REGULATOR;
See 307–204 for parts.
COUPLER, quick disconnect
SWIVEL; See 306–861 for parts.
NIPPLE, 1/4 npt
HOSE, fluid, cpld
SPRAY GUN;
See 307–260 for parts.
NIPPLE, 3/8 npt
TEE, pipe; 1/4 npt
BALL VALVE;
See 306–861 for parts.
ELBOW, street; 1/4 npt
FITTING, pin
Qty
1
1
1
1
1
1
1
1
1
1
1
111
109
107
101
110
106
113
102
108
108
Part No.
210–890
from
Dispense Kit
222–082
Part No.
220–955
from
Dispense Kit
237–889
103
3
7305A
307–879
13
Parts
Model 226–343
Dispense Kit 222–357
120-lb Drum Size Unit with Portable Base
Ref
No.
Part No.
Description
101
109–075
102
103
106
107
108
208–536
202–577
165–198
109–167
206–408
109
110
156–849
218–029
111
210–657
112
113
114
115
100–840
169–971
100–040
100–509
AIR REGULATOR;
See 307–204 for parts.
COUPLER, quick disconnect
SWIVEL
NIPPLE, 3/8 npt x 1/4 npt
HOSE, fluid, cpld
SPRAY GUN;
See 306–796 for parts.
NIPPLE, 3/8 npt
FILTER, fluid; 60 mesh
(250 micron)
BALL VALVE;
See 306–861 for parts.
ELBOW, street; 1/4 npt
FITTING, pin
PLUG; 3/8” npt
PLUG; 1/4” npt
Ref
No. Part No.
1
206–699
2
222–357
3
4
204–674
203–622
4a
4b
4c
4d
4e
4f
4g
191–750
802–275
191–747
100–214
100–132
113–660
113–646
Description
Qty
PUMP, 15:1 Ratio Fire-ball;
See 306–531 for parts.
DISPENSE KIT;
See Parts List at right.
COVER; See 306–345 for parts.
BASE, portable
Contains 4a to 4g
BASE, drum
BOLT, hex hd; 5/16”–18 x 1.5”
BRACKET
WASHER, lock
WASHER, flat
RIVET
CASTER; polyurethane
1
1
1
1
1
2
2
2
2
16
4
114
112
* Or tip of choice. Refer to 307–848 for Reverse-A-Clean
spray tip choices.
111
110
109
101
113
106
115
107
103
102
108
3
4b
4d
4e
4c
4a
4f
4g
7306A
14
307–879
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
Accessories
Accessories must be purchased separately.
Use only GENUINE GRACO PARTS AND ACCESSORIES.
Air Line Lubricator
Bleed–type Master Air Valve 107–142
250 psi (1.7 MPa, 17.4 bar) Maximum Working
Pressure
300 psi (2.1 MPa, 21 bar) Maximum Working Pressure
214–847
3/8” npt
214–848
1/2” npt
Relieves air trapped in the air line between the
pump air inlet and this valve when closed.
1/2” npt
Air Regulator
300 psi (2.1 MPa, 21 bar) Maximum Working Pressure
109–075
3/8” npt
104–266
1/2” npt
Pump Runaway Valve 215–362
180 psi (1.2 MPa, 12 bar) Maximum Working
Pressure
Shuts off air supply to the pump if the pump
accelerates beyond the pre-adjusted setting
due to an empty supply container, interrupted fluid supply to the pump or excessive
cavitation.
3/4” npt(f)
Grounding Clamp & Wire 222–011
12 ga, 25 ft (7.6 m) wire
Air Line Filter
250 psi (1.7 MPa, 17.4 bar) Maximum Working
Pressure
106–148
3/8” npt
106–149
1/2” npt
Filter Screen
To replace standard 60 mesh (250 micron)
filter screen.
Follow Plate 220–654
For 120 lb drum size. See Instruction Manual
306–345 for parts.
167–024
30 mesh (595 micron)
Typically used with filled materials.
167–026
100 mesh (149 micron)
Typically used with unfilled materials
307–879
15
Manual Change Summary
This manual went from Rev. J to Rev. M to make the following changes:
PCN Rev. K is incorporated in this revision to add Models 231–384 (120-lb rollaround) and
231–385 (400-lb stationary).
New design of portable base, Part No. 203–622, is included in Models 226–268 and 226–343.
Each Dispense Kit includes a Reverse-A-Clean spray tip.
Graco Warranty
Graco warrants all equipment listed in this manual which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. With the exception of
any special extended or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or
replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed,
operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or
substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance or structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT
NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, gas engines,
switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance
in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties
reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures
judiciaires exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Phone Number
TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to you:
1–800–367–4023 Toll Free
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Sales Offices: Minneapolis, Detroit, Los Angeles
Foreign Offices: Belgium, Canada, England, Korea, France, Germany, Hong Kong, Japan
GRACO INC.
P.O. BOX 1441 MINNEAPOLIS, MN
PRINTED IN U.S.A.
16
307–879
307–879
55440–1441
February 1988, Revised July 1997
Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Download PDF

advertisement