Graco 308293E Model M-1265, Series B Optimiser HVLP Spray Gun Owner's Manual

Add to my manuals
28 Pages

advertisement

Graco 308293E Model M-1265, Series B Optimiser HVLP Spray Gun Owner's Manual | Manualzz

INSTRUCTIONS–PARTS LIST

This manual contains important warnings and information.

READ AND RETAIN FOR REFERENCE

Model M-1265

Optimiser

HVLP Spray Gun

100 psi (7 bar) Maximum Working Fluid Pressure

100 psi (7 bar) Maximum Working Air Pressure

65 psi (4.5 bar) Maximum Compliant Inbound Air Pressure

U.S. Patent Pending

308–293

Rev. E

Supersedes D

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

COPYRIGHT 1993, GRACO INC.

Table of Contents

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

28

Dimensions

Warnings

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

28

NO TAG

Selection Charts 4

Air Flow and Atomizing Pressure

Typical Installation

. . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7

8

9

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Daily Gun Care, Flushing, and Cleaning . . . . . . . . . .

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Part Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Accessories

Warranty

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

25

Back Cover

13

14

18

19

23

24

Symbols

Warning Symbol

WARNING his symbol alerts you to the possibility of serious injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to or destruction of equipment if you do not follow the instructions.

INSTRUCTIONS

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture, malfunction or start unexpectedly and result in serious injury.

This equipment is for professional use only.

Read all instruction manuals, tags, and labels before operating the equipment.

Use the equipment only for its intended purpose. If you are uncertain about usage, call Graco

Technical Assistance at 1–800–543–0339.

Do not alter or modify this equipment. Use only genuine Graco parts and accessories.

Check equipment daily. Repair or replace worn or damaged parts immediately.

Use this equipment only in low pressure, air spray systems.

Do not exceed the maximum working pressure of the lowest rated system component. This equipment has a 100 psi (7 bar) maximum working fluid and air pressure .

Do not lift pressurized equipment.

Use fluids or solvents that are compatible with equipment wetted parts. See the Technical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.

Methylene Chloride with formic or propionic acid is not recommended as a flushing or cleaning solvent with this gun or any other device with nylon or aluminum components as it can damage these parts.

Comply with all applicable local, state and national fire, electrical and other safety regulations.

PRESSURIZED EQUIPMENT HAZARD

Spray from the gun, hose leaks or ruptured components can splash fluid in the eyes or on the skin and cause serious injury.

Do not stop or deflect fluid leaks with your hand, body, glove or rag.

Follow the Pressure Relief Procedure on page 13 when: you are instructed to relieve pressure; stop spraying; clean, check or servicing the equipment; and install or clean fluid nozzles.

Never point the spray gun at anyone or at any part of the body.

Never put hand or fingers over the spray nozzle.

Tighten all fluid connections before operating the equipment.

Check the hoses, tubes and couplings daily. Replace worn, damaged or loose parts immediately.

Permanently coupled hoses cannot be repaired; replace the entire hose.

Route hoses away from traffic areas, sharp edges, moving parts and hot surfaces.

Do not use the hoses to pull equipment.

FIRE AND EXPLOSION HAZARD

Poor air ventilation, open flames or sparks can cause a hazardous condition and result in fire or explosion and serious injury.

Provide fresh air ventilation to avoid the buildup of flammable fumes from solvent or the fluid being sprayed.

Extinguish all open flames or pilot lights in the spray area.

Electrically disconnect all equipment in the spray area.

Keep the spray area free of debris, including solvent, rags and gasoline.

Do not turn on or off any light switch in the spray area while operating or if fumes are present.

Do not smoke in the spray area.

Do not operate a gasoline engine in the spray area.

TOXIC FLUID HAZARD

Hazardous fluids or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin, inhaled, or swallowed.

Know the specific hazards of the fluid you are using. Read the fluid manufacturer’s warnings.

Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local, state and national guidelines.

Dress appropriately for your application. Wear protective eyewear, noise protection for the ears, a personal respirator, gloves and clothing.

Selection Charts

TERMS:

Light Fluid: Up to 18 seconds with No. 2 Zahn cup (20 centipoise)

Medium Fluid: 19 to 28 seconds with No. 2 Zahn cup (20–64 centipoise)

Heavy Fluid: +28 seconds with No. 2 Zahn cup (greater than 64 centipoise) --

2.8 Volatile Organic Compounds, High-solid Polyurethanes, Heavy Waterborne Enamels

CHART 1: GUN ASSEMBLIES

Standard Gun Assemblies

With standard needle/nozzle/air cap kit

Standard

Complete

Gun Assy.

Part No.

236–013

236–014

236–015

236–016

Includes:

Standard

Needle/

Nozzle/Air

Cap Kit P/N

235–309

235–310

235–311

235–312

Orifice Size

Material Usage

(See TERMS above)

0.042” (1.067 mm) Light to Medium Fluids or Low Fluid Flow

[5–8 oz/min (0.15–0.24 l/min)]

0.055” (1.397 mm) Light to Medium Fluids or Medium Fluid

Flow [6–12 oz/min (0.18–0.36 l/min)]

0.070” (1.778 mm) Medium to Heavy Fluids or Medium Fluid

Flow [6–12 oz/min (0.18–0.36 l/min)]

0.086” (2.184 mm) Heavy Fluids or High Fluid Flow

[10–15 oz/min (0.3–0.45 l/min)]

Optional Gun Assemblies – available as “Build to Order”

With optional needle/nozzle/air cap kit

Optional

Complete

Gun Assy.

Part No.

236–020

236–021

236–022

236–027

236–028

Includes:

Optional

Needle/

Nozzle/Air

Cap Kit P/N

235–306

235–307

235–308

235–313

235–314

Orifice Size

Material Usage

(See TERMS above)

0.020” (0.508 mm) Light Fluids or Low Fluid Flow

[3–6 oz/min (0.09–0.18 l/min)]

0.026” (0.660 mm) Light Fluids or Low Fluid Flow

[3–6 oz/min (0.09–0.18 l/min)]

0.030” (0.762 mm) Light to Medium Fluids or Low Fluid Flow

[5–8 oz/min (0.15–0.24 l/min)]

0.110” (2.794 mm) Heavy Fluids or High Fluid Flow

[12–18 oz/min (0.36–0.54 l/min)]

0.125” (3.175 mm) Heavy Fluids or High Fluid Flow

[12–18 oz/min (0.36–0.54 l/min)]

Selection Charts

CHART 1: GUN ASSEMBLIES (continued)

Optional Non-HVLP Compliant Gun Assemblies

With standard needle and nozzle and optional high pressure air cap

Includes:

Optional

Complete

Gun Assy.

Part No.

236–023

SST

Needle

P/N

236–123

*

Nozzle

P/N

276–293

High

Pressure {

Air Cap

P/N

189–755

Orifice Size

Material Usage

(See TERMS on page 4)

0.042” (1.067 mm) Light to Medium Fluids or Low Fluid Flow

[5–8 oz/min (0.15–0.24 l/min)]

236–024 236–124 276–294 189–755 0.055” (1.397 mm) Light to Medium Fluids or Medium Fluid

Flow [6–12 oz/min (0.18–0.36 l/min)]

* Maximum recommended torque to install molded fluid nozzle in the spray gun is 35 in-lbs (4 N S m).

{ See atomizing air pressure chart on page 7.

CHART 2: NEEDLE/NOZZLE/AIR CAP KITS

Standard Needle/Nozzle/Air Cap Kits

Includes:

Standard

Needle/

Nozzle/Air

Cap Kit P/N

235–309

235–310

235–311

235–312

SST

Needle

P/N

236–123

236–124

236–125

236–126

*

Nozzle

P/N

276–293

276–294

276–295

276–296

Air Cap

P/N

188–754

188–754

188–755

188–756

Orifice Size

0.042” (1.067 mm)

0.055” (1.397 mm)

0.070” (1.778 mm)

0.086” (2.184 mm)

Optional Needle/Nozzle/Air Cap Kits – available as “Build to Order”

Includes:

*

Optional

Needle/

Nozzle/Air

Cap Kit P/N

235–306

235–307

235–308

235–313

235–314

Needle Shaft

Assy P/N

224–849

224–849

224–849

224–849

224–849

SST

Needle

P/N

185–854

185–855

185–730

185–735

185–736

*

Nozzle

P/N

276–290

276–291

276–292

276–297

276–298

Air Cap

P/N

188–754

188–754

188–754

188–757

188–758

Orifice Size

0.020” (0.508 mm)

0.026” (0.660 mm)

0.030” (0.762 mm)

0.110” (2.794 mm)

0.125” (3.175 mm)

Maximum recommended torque to install molded fluid nozzle in the spray gun is 35 in-lbs (4 N S m).

Selection Charts

CHART 3: OPTIONAL ORIFICE PURGE

SST NEEDLE

For low flow rates or light viscosity fluid, select the smaller nozzle sizes.

For high flow rates or high viscosity fluid, select the larger nozzle sizes.

Optional

Stainless Steel

Orifice-Purge

Needle Part No.

186–931

186–932

186–933

186–934

186–935

186–936

Orifice Size

0.042” (1.067 mm)

0.055” (1.397 mm)

0.070” (1.778 mm)

0.086” (2.184 mm)

0.110” (2.794 mm)

0.125” (3.175 mm)

Use these needles to purge fluid out of the nozzle orifice to prevent plugging of the tip with fast drying material. A needle shaft assembly (part no.

224–849) must be used with these needles and replaces the standard one-piece needles.

Selecting the Proper Needle/Nozzle/Air

Cap Set

The High Volume Low Pressure Spray Gun’s needle/ nozzle sets range in size to provide different fluid flow rates. Chart 1 shows the recommended combinations based on fluid viscosities and flow rates.

As a general guideline, use the fluid nozzle that will give the required flow with the needle fully triggered at the lowest fluid pressure.

Using an air cap size that is smaller than the nozzle/ needle size is not recommended.

NOTE: To help select the proper needle/nozzle size, a fluid pressure gauge may be connected temporarily to the gun fluid inlet to determine the fluid pressure.

Selection Problems and Solutions

PROBLEM

Fluid pressure is too high (greater than

10 psi [0.7 bar]) with gun triggered

Using a low pressure setting, the fluid flow is too high, making it necessary to restrict needle travel to reduce fluid flow.

Fluid system will not operate at low enough fluid pressure [below 10 psi

(0.7 bar)]

POSSIBLE

CAUSE

Using set with too small orifice

Using set with too large orifice

There’s no fluid regulator or air regulator is not sensitive enough

SOLUTION

Use needle/ nozzle/air cap set with larger orifice

Use needle/ nozzle/air cap set with smaller orifice

Add low pressure fluid regulator or add more sensitive air regulator on pressure pot

Air Flow and Atomizing Pressure

NOTE: All tests were completed with the fan fully open.

Air Flow

30

28

26

24

22

20

18

16

14

12

Models 236–023 & 236–024

All other models

10

8

6

4

2

0

15 25 35 45 55 65 75 85 95

GUN INLET PRESSURE (psi)

Atomizing Air Pressure

(inlet pressure vs. atomizing pressure)

Models 236–013 to 236–016 and

236–020 to 236–028

20

18

16

14

12

10

8

6

4

2

0

15 25 35 45 55 65 75 85 95

GUN INLET PRESSURE (psi)

Atomizing Air Pressure

(inlet pressure vs. atomizing pressure)

Models 236–023 and 236–024

60

50

Model 236–023

Model 236–024

40

30

20

10

0

15 25 35 45 55 65 75 85 95

GUN INLET PRESSURE (psi)

Gun Inlet

Pressure

20 psi (1.4 bar)

30 psi (2.1 bar)

40 psi (2.8 bar)

50 psi (3.5 bar)

60 psi (4.2 bar)

70 psi (4.9 bar)

80 psi (5.6 bar)

90 psi (6.3 bar)

100 psi (7.0 bar)

Nominal Atomizing Pressure

Model 236–023 Model 236–024

6 psi (0.41 bar)

10 psi (0.70 bar)

7 psi (0.48 bar)

12 psi (0.83 bar)

16 psi (1.10 bar)

21 psi (1.45 bar)

26 psi (1.79 bar)

18 psi (1.24 bar)

24 psi (1.66 bar)

30 psi (2.10 bar)

32 psi (2.21 bar)

38 psi (2.62 bar)

43 psi (2.97 bar)

48 psi (3.31 bar)

36 psi (2.48 bar)

42 psi (2.90 bar)

48 psi (3.31 bar)

54 psi (3.73 bar)

Gun Inlet Pressure

15 psi (1.04 bar)

25 psi (1.73 bar)

35 psi (2.42 bar)

45 psi (3.11 bar)

55 psi (3.80 bar)

65 psi (4.49 bar)

75 psi (5.18 bar)

85 psi (5.87 bar)

95 psi (6.56 bar)

Nominal Atomizing Pressure

1.5 psi (0.11 bar)

3.0 psi (0.21 bar)

4.5 psi (0.31 bar)

6.0 psi (0.41 bar)

8.5 psi (0.59 bar)

10.0 psi (0.70 bar)

13.0 psi (0.90 bar)

15.5 psi (1.07 bar)

18.0 psi (1.24 bar)

308-293 7

Typical Installation

NOTE : See the ACCESSORIES section for accessories recommended to install the system.

E F

A

G H

B

C

KEY

A Model M-1265 Spray Gun

See page 4 for part numbers.

B Fluid Inlet; 3/8 npsm (R3/8–19)

C Air Inlet; 1/4 npsm

D Air Hose

Recommend 5/16” (7.9 mm) ID hose

Optional 3/8” (9.5 mm) ID hose

E Air Shut-off Valve

F Air Regulator

G Air Filter

H Air Supply Line

The M-1265 HVLP Spray Gun

The Model M-1265 HVLP Spray Gun was designed to produce the highest quality finish with today’s fluids as well as the the Low V.O.C. (volatile organic compound) fluids of tomorrow.

This spray gun can spray most coatings or finishes currently being used for automotive refinish, industrial, aerospace, marine, wood, plastic and architectural applications, while easily operating from any paint delivery system, including cups, pressure pots, or remote pumps for production line operation.

The Model M-1265 HVLP Spray Gun typically utilizes

65 psi (4.55 bar) inbound air pressure to produce high quality paint finishes at 10 psi (0.07 bar) atomizing air pressure.

The air regulator must have a minimum air flow capacity of 30 scfm at 100 psi (7 bar) air pressure.

NOTE: If the gun’s hanging hook is needed, remove the gun trigger and replace the gun plate with the hook, then reinstall the trigger. See the parts drawing, page 23.

D

Ventilate the Spray Booth

WARNING

To prevent hazardous concentrations of toxic and/or flammable vapors, spray only in a properly ventilated spray booth.

Never operate the spray gun unless ventilation fans are operating.

Check and follow all of the National,

State and Local codes regarding air exhaust velocity requirements.

Check and follow all local safety and fire codes.

02018

1. Connect the Air Line

NOTES:

You must install an air pressure regulator (F) on the gun air line to control air pressure to the gun. See

Fig. 2.

Setup

2. Connect the Fluid Hose

NOTES:

Before connecting the fluid line, blow it out with air and flush it with solvent. Use solvent which is compatible with the fluid to be sprayed.

Install a fluid regulator (L) on the fluid line to control fluid pressure to the gun. See Fig. 4.

If your regulated air source does not have a filter , install an air filter (G) on the air line to ensure a dry, clean air supply to the gun. Dirt and moisture can ruin the appearance of your finished workpiece.

See Fig. 2.

Filter the fluid line of coarse particles and sediment to avoid clogging the fluid nozzle and causing finishing defects.

A.

Connect the air hose (D) to the 1/4 npsm gun air inlet (C).

A.

Connect the fluid hose (J) to the gun fluid inlet (B)

3/8–18 npsm [R 3/8–19] compound thread.

B

J

C

D

Fig. 1 02051

B.

Connect the other end of the air hose (D) to a regulated air supply line (H).

NOTE: Fig. 2 shows the filter (G) air regulator (F), and air shut-off valve (E) on the air supply line.

H G F

Fig. 3

B.

Connect the other end of the fluid hose (J) to a regulated fluid supply line (K).

02052

NOTE: Fig. 4 shows the fluid regulator (L) and fluid shut-off valve (M) on the fluid supply line (K).

K

L

M

J

E D

Fig. 2 01990

Fig. 4

02054

Setup

3. Flush the Spray Gun.

Before running any paint through the spray gun, flush the gun out with a solvent that is compatible with the fluid to be sprayed, using the lowest possible fluid pressure and a grounded metal container.

6. Adjust the Spray Pattern

WARNING

COMPONENT RUPTURE HAZARD

Do not exceed the 100 psi (7 bar) maximum fluid and air pressure of this gun. Higher pressures can cause parts to rupture and result in serious injury.

Follow these steps to establish the correct fluid flow and air flow:

A.

Turn the fluid adjustment knob (9) counterclockwise until no restriction of the trigger movement is felt. When the knob is turned far enough, the trigger should be able to touch the gun handle when the gun is triggered.

Fig. 5

WARNING

PRESSURIZED EQUIPMENT HAZARD

To reduce the risk of a serious injury whenever you are instructed to relieve pressure, always follow the Pressure

Relief Procedure on page 13.

02053

4. Relieve the Pressure.

5. Position the Air Cap

Rotate the air cap as needed to achieve the desired spray pattern direction. To create a round pattern, turn the pattern air off by turning the pattern adjustment knob (13a) fully clockwise. Refer to Fig 12.

Fig. 7 open

9

02017

Vertical Pattern

Horizontal Pattern

02020 Fig. 6

10 308-293

Setup

6. Adjust the Spray Pattern (continued)

B.

Adjust the fluid flow using the fluid pressure regulator (L) installed in the gun fluid line. Typical industrial flow rates will vary with regulator pressures from 5 to 10 psi (0.35 to 0.7 bar).

NOTE: A larger fluid nozzle at a reduced fluid pressure will maintain the same flow rate, but slow down the fluid stream (velocity). When air is applied, this allows the air to act on the fluid longer and improve the atomization.

D.

If further fluid adjustment is needed at the gun, turn the fluid adjustment knob (9) clockwise to reduce the volume of fluid output and obtain the desired results.

L

9 close

Fig. 8 02059

C.

Hold the gun parallel to the floor and adjust the fluid pressure to yield a 1 to 6 inch (25.4 to 152.4 mm) straight fluid stream before the stream falls off.

1–6 in.

(25.4–152.4 mm) straight fluid stream

Fig. 9

Fluid Velocity of Fluid Nozzles at the Same Flow Rate

0.042

(1.067)

0.055

(1.397)

0.070

(1.778)

0.086

(2.184)

Orifice Size in inches (mm)

Fig. 10

0.110

(2.794)

02106

02105

Fig. 11

CAUTION

Restricting the trigger and fluid needle travel by continuously spraying with the fluid adjustment knob closed (turned clockwise), will cause accelerated abrasive wear on the fluid needle and wear on the trigger/air valve shaft interface.

For the best results, use the gun fluid regulator to adjust the fluid flow or use a different size needle/ nozzle/air cap combination. Refer to page 5.

02017

NOTES:

If the fluid adjustment knob is turned in all the way the gun will emit only air.

For continuous spraying, turn the fluid adjustment knob (9) counterclockwise until no restriction of the trigger movement is felt. When the knob is turned far enough, the trigger should be able to touch the gun handle when the gun is triggered. This provides maximum fluid flow and prevents premature wear on the fluid nozzle.

continued on the next page

308-293 11

Setup

6. Adjust the Spray Pattern (continued)

E.

Open the pattern adjusting valve (13a) by turning it fully counterclockwise.

13a

Open

(wider pattern)

Close

(narrower pattern*)

G.

Test the spray pattern and atomization while holding the gun about 6 to 8 inches (150 to 200 mm) from the test piece.

H.

The spray pattern may be too wide with the pattern adjustment knob (13a) turned fully counterclockwise. Turn the pattern adjustment knob clockwise until you have the desired pattern size.

*NOTE: T urning the pattern adjustment knob fully clockwise will produce a round pattern.

I.

Check the atomization quality again. Adjust the gun air supply pressure with the air pressure regulator in 5 psi (0.35 bar) increments until you obtain the desired atomization.

J.

If after increasing the gun air supply pressure the atomization is still unacceptable, try installing a larger fluid nozzle size to reduce the fluid velocity.

Refer to Fig. 10. Repeat steps 6.E.–I. until you obtain the desired atomization.

Fig. 12

F.

Using the air pressure regulator (F), set the gun air supply pressure at 50 psi (3.5 bar).

If available, use the fluid manufacturer’s recommendations to set the air line pressure for a high volume, low pressure application.

NOTE: Local laws may limit the maximum pressure to 10 psi (0.7 bar) at the air cap for HVLP compliance.

CAUTION

Trigger the gun whenever you tighten or remove the nozzle. This keeps the needle seat away from the nozzle seating surface and prevents the seat from being scratched.

When tightening the nozzle, do not exceed 35 in-lbs

(4 N m) torque. Over-tightening the nozzle can cause the nozzle hex to round, can affect the spray pattern, and is unnecessary to guarantee a seal.

F

01997

Fig. 13

12 308-293

Operation

Pressure Relief Procedure

WARNING

PRESSURIZED EQUIPMENT HAZARD

The equipment stays pressurized until pressure is manually relieved. To reduce the risk of serious injury from pressurized fluid, accidental spray from the gun or splashing fluid, follow this procedure whenever you:

Are instructed to relieve pressure

Stop spraying

Check, clean or service any system equipment

Install or clean fluid nozzles.

1. Turn off the air and fluid supply to the gun.

2. Trigger the gun into a grounded metal waste container to relieve air and fluid pressure.

Applying the Fluid

When using the HVLP spray gun, instead of a conventional air spray gun, you may notice that you need to use a slightly slower hand movement and make fewer passes with the gun to coat a part. This is due to the reduced spray velocity produced by lower HVLP air pressures, along with a larger fluid particle size because there is less air to blow off solvents than what is produced by conventional air spray. Take care to avoid runs or sags as you spray.

1. To achieve the best results when applying fluid, keep the gun perpendicular to the surface and maintain a consistent distance of approximately 6 to 8 inches (150 to 200 mm) from the object being sprayed. See Fig. 14.

2. To obtain an even finish, use smooth, even strokes across the object being sprayed with 50% overlap.

3. Paint using parallel strokes. This spray gun applies all coatings evenly without cross coating.

NOTE: To eliminate the need to shut off the air pressure at the air supply, install a quick-disconnect at the gun inlet fitting. See Accessories.

Fig. 14

WRONG RIGHT

0793

308-293 13

Daily Gun Care, Flushing, and Cleaning

WARNING

PRESSURIZED EQUIPMENT HAZARD

To reduce the risk of a serious injury whenever you are instructed to relieve pressure, always follow the Pressure

Relief Procedure on page 13.

CAUTION

Clean all parts with a non-conductive solvent, compatible with the fluid being sprayed. Conductive solvents can cause the gun to malfunction.

Methylene chloride with formic or propionic acid is not recommended as a flushing or cleaning solvent with this gun as it will damage nylon components.

CAUTION

Solvent left in gun passages could result in a poor quality paint finish. Do not use any cleaning method which may allow solvent into the gun air passages.

Do not point the gun up while cleaning it.

Do not wipe the gun with a cloth soaked in solvent; ring out the excess.

Do not immerse the gun in solvent.

02056 02027

Do not use metal tools to clean the air cap holes as this may scratch them; scratches can distort the spray pattern.

02057 02055

General System Maintenance

1. Relieve the pressure.

2. Clean the fluid and air line filters daily.

3. Check for any fluid leakage from the gun and fluid hoses. Tighten fittings or replace equipment as

14 needed.

308-293

4. Flush the gun before changing colors and whenever you are done operating the gun.

Daily Gun Care, Flushing, and Cleaning

WARNING

PRESSURIZED EQUIPMENT HAZARD

To reduce the risk of a serious injury whenever you are instructed to relieve pressure, always follow the Pressure

Relief Procedure on page 13.

4. Point the gun down into a grounded metal container, and flush the gun with solvent until all traces of paint are removed from the gun passages.

1. Relieve the pressure.

2. Disconnect the fluid supply hose (J) from the gun; do not disconnect the air supply hose.

J

Fig. 3 02053

5. Turn off the solvent supply.

6. Relieve the pressure. Disconnect the solvent supply.

7. Disconnect both the solvent (N) and air (D) supply hoses from the gun.

Fig. 1

3. Connect the solvent supply hose (N) to the gun.

02052

D

N

N

02051

02052

Fig. 2 02052

Fig. 4

308-293 15

Daily Gun Care, Flushing, and Cleaning

8. Remove the air cap ring (12) and air cap (19).

9. Trigger the gun while you remove the fluid nozzle

(20) from the gun with the gun wrench (35).

12. With the gun pointed down, clean the front of the gun, using the soft-bristle brush and solvent.

12, 19

35

20

Fig. 5

CAUTION

Trigger the gun whenever you tighten or remove the nozzle. This keeps the needle seat away from the nozzle seating surface and prevents the seat from being scratched.

02060A

10. Soak the ring, air cap, and fluid nozzle in solvent.

11. Dip the end of a soft-bristle brush into a compatible solvent. Do not continuously soak the brush’s bristles with solvent and do not use a wire brush.

Fig. 7 02062A

13. Scrub the the air cap ring, air cap, and fluid nozzle with the soft-bristle brush. To clean out air cap holes, use a soft implement, such as a toothpick, to avoid damaging critical surfaces. Clean the air cap and fluid nozzle daily, minimum. Some applications require more frequent cleaning.

Fig. 6

16 308-293

02007 Fig. 8 02011

Daily Gun Care, Flushing, and Cleaning

14. Trigger the gun while you install the fluid nozzle

(20) with the gun wrench (35).

17. After cleaning the gun, lubricate the following parts with lubricant 111–265 daily:

CAUTION

When tightening the nozzle, do not exceed 35 inlbs (4 N S m) torque. Over-tightening the nozzle can cause the nozzle hex to round, can affect the spray pattern, and is unnecessary to guarantee a seal.

D Pattern adjustment valve threads

D Fluid adjustment knob threads

D Trigger pivot pin

15. Install the air cap ring (12) and air cap (19).

D Fluid needle shaft; refer to the Service section to remove and reinstall the needle

NOTE: See Accessories to order lubricant 111–265.

35

20

12, 19

Lubricate

Fig. 9 02060A

16. Dampen a soft cloth with solvent and wring-out the excess. Point the gun down and wipe off the outside of the gun.

Lubricate

02019

02063

Fig. 11

Fig. 10

308-293 17

Troubleshooting

WARNING

PRESSURIZED EQUIPMENT HAZARD

To reduce the risk of a serious injury, always follow the Pressure Relief Procedure on page 13 before checking or repairing any part of the gun or system.

PROBLEM

Fluid flow is fluttering while spraying

Fluid flow fades while spraying high viscosity fluids

No round pattern control

Pattern becomes off-set or heavy on ends

Fluid system will not operate at low enough fluid pressure [below 10 psi

(0.7 bar)]

CAUSE

1. Fluid nozzle not tight enough

2. Fluid filter clogged

3. Fluid adjustment knob not properly set

4. Baffle (item 11) installed wrong or damaged

SOLUTION

1. Tighten fluid nozzle; Do not exceed 35 in-lbs (4 N m) torque

2. Check fluid filter

3. Adjust the fluid adjustment knob for less feathering or use a larger size nozzle

4. Check if baffle protrusion is properly inserted into gun insert hole; see page 23. Replace baf fle if damaged

1. Air hose size is too restricted for higher air flows

2. Fluid pressure too low , causing fluid flow to reduce when gun is elevated

Baffle (item 11) installed wrong or damaged

1. Use larger 3/8 in. ID air hose, part no. 185–353. See ACCES-

SORIES

2. Raise fluid pressure at source or use a smaller fluid nozzle

Check if baffle protrusion is properly inserted into gun insert hole; see page 23. Replace baffle if damaged

1. Fluid nozzle is over tightened

2. Air cap too tight

3. Air cap horn holes plugged

There’s no fluid regulator or air regulator on pressure pot is not sensitive enough at low pressures

1. Do not exceed 35 in-lbs (4 N m) torque on nozzle. Replace nozzle if damaged

2. Loosen air cap retaining ring

3. Clean air cap horn holes with non-metallic item such as a toothpick

Add low pressure fluid regulator or add more sensitive air regulator on pressure pot

18 308-293

Service

Items Needed for Service

Gun Wrench – provided

Seal Installation Tool – provided

Adjustable Wrench

Screw Driver

Lubricant Part No. 111–265; see Accessories to order

12, 19

Compatible Solvent

NOTES: a. Gun Repair Kit 236–007 is available. The kit includes the air valve assembly (14), ring packing (22) u-cup seals (32 & 33), and packing assembly (39). See page 24 to order.

b. The following procedure covers the replacement of all the parts included in the Gun

Repair Kit.

c. The Optional M-1265 Spray Gun (part no.

236–020 to 236–022, 236–027 and 236–028) have a two piece needle assembly, which includes a SST needle shaft assembly and a

SST needle tip, instead of the one-piece needle shown in the following instructions. See

Chart 2 on page 5 for part numbers.

Fig. 1

35

20

02060A

4. Remove the fluid adjustment knob (8) and fluid spring (16). See Fig. 5.

5. Pull the fluid needle (21) out the back of the gun.

6. Remove the trigger (3).

7. Remove the fluid adjustment nut (6), spring (15), and air valve (14).

8. To remove the packing adjustment screw (31), insert a thin-blade screw driver (A) through the back of the gun and into the packing adjustment screw

(31) as shown in Fig. 2. Be careful not to nick or damage parts with the tool.

Disassembly

1. Follow the Pressure Relief Procedure Warning on page 13 to relieve fluid pressure.

2. Remove the air cap retaining ring (12) and air cap

(19).

3. Trigger the gun while you remove the fluid nozzle

(20) with the gun wrench (35). See Fig. 1.

CAUTION

Trigger the gun whenever you tighten or remove the nozzle. This keeps the needle seat away from the nozzle seating surface and prevents the seat from being scratched.

Fig. 2

A

31

308-293 19

CAUTION

Do not use excessive force to push out the packing assembly (39) or the u-cup seal (33) as this may bend the fluid needle (21). Refer to Fig. 3 and 4. If packings are difficult to remove, use a 3/16 in.

plastic rod to push them out.

Service

11. Clean the parts. Check the fluid needle (21) for damage or excessive wear. Replace if necessary.

12. Check the baffle (11) for damage. If it is damaged, carefully pry it off with a screwdriver and replace it.

13. Lightly lubricate the parts indicated in Fig. 5 with lubricant 111–265.

12 19 20 3

9. Push the three piece packing assembly (39) out the back of the gun, with the threaded end of the fluid needle, as shown in Fig. 3.

11 4

5

21 3

33

14 1

21 1

02109A

Fig. 3

10. Use the threaded end of the fluid needle (21) to push out the u-cup seal (33) as shown in Fig. 4.

3

4

1

2

Fig. 5

3 39 31

15

1 16

Lightly lubricate

3 6

Lightly lubricate threads

Torque to 35–40 in-lbs (3.9–4.5 N m)

2 8

Be sure the baffle protrusion is properly inserted into the gun insert hole before tightening the nozzle

02103A

21

02022A

Fig. 4

Service

Assembly

1. Insert the fluid needle (21) through the front of the gun as shown in Fig. 6. Install the new packing assembly (39) by placing them on the end of the needle tip. Orientate the packings as shown in Fig.

6.

4. Place the new u-cup seal (33) on the seal installation tool (42) with the u-cup lips facing the tool as shown in Fig. 8.

5. Push the packing (33) into the gun until a definite snap is felt.

1

33 1

2

42

39

3

21

1

2

3

Washer

U-cup; lips face down

Spreader

Fig. 6

02024

2. Place the packing adjustment screw (31) over the packing assembly and start the threads into the gun. Then remove the needle.

3. Insert a thin-blade screw driver (A) through the back of the gun and into the packing adjustment screw (31) as shown in Fig. 7. Be careful not to nick or damage parts with the tool. Turn the screw with the screw driver (about 3 turns); the packing will still be loose.

1 U-cup lips face the tool

Fig. 8

02023

6. Place the new air valve assembly (14) on the fluid needle (21), against the nut (B). See Fig. 9. This helps align the entrance of the air valve stem into the inside diameter of the u-cup seal (33) without damaging the seal lip.

7. Install the fluid needle (21) and the air valve assembly (14) into the back of the gun.

A

31

21

14

B

02108

Fig. 7

02110 Fig. 9

308-293 21

Service

8. Tighten the packing adjustment screw (31) with the gun wrench (35), as shown in Fig. 10, until you can feel a slight drag on the fluid needle. Do not overtighten the screw as this may bind the needle movement.

16. Trigger the gun to test the needle movement. If the needle does not return after the trigger is released or is slow in returning, loosen the packing adjustment screw (31) with the gun wrench (35) until the needle returns freely. See Fig. 10.

17. Trigger the gun while you install the fluid nozzle

(20) with the gun wrench (35).

31

Fig. 10

35

02104A

CAUTION

When tightening the nozzle, do not exceed 40 in-lbs

(4.5 N m) torque. Over-tightening the nozzle can cause the nozzle hex to round, can affect the spray pattern, and is unnecessary to guarantee a seal.

9. Install the trigger (3). Torque the screw (5) to

10–15 in-lbs (1.1–1.7 N m). See Fig. 12.

10. Remove the u-cup seal (32) from the fluid adjustment nut (6). Refer to Fig. 11. Be careful not to damage the seal surface or the nut’s internal threads.

11. Install the new u-cup seal (32) with the seal installation tool (42) with the u-cup lips facing toward the tool as shown in Fig. 11. This will help apply even pressure to the u-cup lips and avoid damaging them.

12. Push the u-cup seal (32) into the fluid adjustment nut (6) until a definite snap is felt.

13. Install the new packing ring (22).

18. Install the air cap ring (12) and air cap (19).

19. Make sure the gun fluid packing assembly is sealing properly by spraying solvent at low pressure before fully pressurizing the gun with the fluid to be sprayed.

If the fluid packing leaks, tighten the packing adjustment screw (31) slightly and retest until the packing seals completely.

12 19 20 3

11 4

1

U-cup lips face the tool

42

5 6

33

14 1

21 1

22

32 1

Fig. 11

6

02021

14. Install the spring (15) and fluid adjustment nut (6).

Torque the nut to 25–35 in-lbs (2.8–4.0 N m). See

Fig. 12.

15. Install the spring (16) and fluid adjustment knob (8).

3 39 31

15

1 16

1 Lightly lubricate

5 6

2

Lightly lubricate threads 2

3 Torque to 35–40 in-lbs (3.9–4.5 N m)

4

Be sure the baffle protrusion is properly inserted into the gun insert hole before tightening the nozzle

5 Torque to 25–35 in–lb (2.8–4.0 N.m)

8

6 Torque to 10–15 in–lb (1.1–1.7 N.m)

Fig. 12

02103A

19

Parts Drawing

20

9 21 1

34

Needle set for optional guns

2 8

5

5

12

11

4

10

25

13d n

13b 3

13c n

Ref No. 13

Fan Air Valve Assembly

Includes items 13a–13d

13a

4 39*

33*

6

3

14*

1

31 n

1

15

1

2

3

4

5

42

Lightly lubricate

Lightly lubricate threads

Torque to 25–35 in-lbs (2.8–4.0 N S m)

Be sure the baffle protrusion is properly inserted into the gun insert hole before tightening the nozzle.

Torque to 10–15 in-lbs (1.1–1.7 N S m)

35

1 16

7 32*

22*

3 6

2 8

8

9

6

7

10

U-cup lips face air valve (14)

U-cup lips face spring (16)

Optional gun hook to replace plate (34)

Torque to 35–40 in–lb (3.9–4.5 N.m)

Torque the screw or any accessory installed in this port to 4–6 in–lb (.35–.53 N.m)

21 1

Needle for standard guns

02025A

Parts List

Part No. 236–013 to 236–016

M-1265 Standard HVLP Spray Gun

With standard needle, nozzle, and air cap

Includes items 1–42

Part No. 236–020 to 236–028

M-1265 Optional HVLP Spray Gun

With optional needle, nozzle, and air cap

Includes items 1–42

Ref

No.

Part No.

Description Qty

3

4

1

2

5

6

8

11

12

13

236–004 GUN BODY

275–852 HOOK, gun

185–761 TRIGGER, two-finger

185–746 PIN, pivot; 10-24 UNC-2B

203–953 SCREW, lock; No. 10–24 UNC-2A x 0.375 in.

188–490 NUT, fluid adjustment

185–745 KNOB, fluid adjustment

275–851 BAFFLE, pattern

276–278 RETAINING RING, air cap

236–006 FAN AIR VALVE ASSY.

Includes items 13a–13d

13a 188–492 S VALVE, fan air

13b 188–700 S NUT, air adjustment

13c n 187–699 S O-RING, split; PTFE

13d n 105–456 S RETAINING RING

14* 236–009 AIR VALVE ASSY.

15

16

111–291 SPRING, compression

110–402 SPRING, compression

19 .

20 .

AIR CAP

FLUID NOZZLE

21 .

– FLUID NEEDLE

22* 188–694 RING PACKING, PTFE r

25 108–382 PLUG

31 n 188–665 SCREW, packing adjustment

32* 110–453 SEAL, u-cup, nut; UHMWPE

33* 188–493 SEAL, u-cup; UHMWPE

34 275–853 PLATE, gun

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

Part No. 236–023 and 236–024

M-1265 Optional Non-HVLP Compliant Spray Gun

With standard needle and nozzle and optional high pressure air cap

Includes items 1–42

Ref

No.

Part No.

Description Qty

35 188–666 WRENCH, gun

39* 236–008 PACKING ASSY.; includes

42 u-cup spreader, u-cup seal

& packing washer

276–268 TOOL, seal installation

* These parts are included in Repair Kit 236–007 , which may be purchased separately .

1

1

1 n Keep these spare parts and the Repair Kit on hand to reduce down time.

.

See selection charts for your gun model on pages

4 and 5 to order air caps, fluid nozzles, and fluid needles.

Manual Change

Summary

The torque values for several parts have been either changed or corrected. Always refer to the torque values in the service section and parts drawing when reassembling the gun. All warnings have been updated.

Accessories

Cleaning Brush 105–749

For use in cleaning gun

Lubricant 111–265

One 4 oz. (113 gr) tube sanitary (non-silicone) lubricant for fluid seals and wear areas.

Fluid Tube Kit 236–318

Allows air and fluid hoses to be more easily strapped together and eases gun movement by the operator.

03405

High Pressure Air Cap 189–755

Optimal air cap for use in non-HVLP compliant operations. Water-base compatible

Air Pressure Verification Kit 224–187

For use in checking gun atomizing air pressure at various supply air pressures. Not to be used for actual spraying.

Assemble kit as shown in drawing below. Screw tube connector into gun’s side port. Turn on the air to the gun, then trigger the gun and read the resulting air pressure.

NOTE: To be “HVLP compliant”, the atomizing air pressure must not exceed 10 psi (0.7 bar).

SST Fluid Pressure Regulator 214–895

250 psi (18 bar) Maximum Inlet Pressure

5-100 psi (0.3-7 bar) Regulated

Pressure Range

To regulate the fluid pressure to the gun. 3/8 npsm inlet, 3/8 npt(f) outlet

Air Hose Assembly 210–867

100 psi (7 bar) Maximum Working Pressure

25 ft (7.625 m) long, 5/16 in. (7.94 mm) ID,

1/4 npsm(f) swivel, buna-n

Air Hose Assembly 185–353

100 psi (7 bar) Maximum Working Pressure

Optional air hose for use when higher air flow is required. 25 ft (7.625 m) long, 3/8 in. (9.53 mm) ID,

1/4 npsm(f) swivel, buna-n

Air Hose Quick-disconnect

Install between gun air inlet fitting and air hose.

208–536 Coupler, 1/4 npt(f)

169–970 Nipple, 1/4 npt(m)

Fluid Hose Assembly 205–142

300 psi (21 bar) Maximum Working Pressure

Nylon with neoprene cover, 0.25 in. (2.4 mm) ID,

3/8 npsm(fbe), 25 ft (7.6 m) long

Air Filter and Moisture Separator 106–149

250 psi (17.5 bar) Maximum

Working Pressure

Removes moisture, oil, and other contaminants from the compressed air supply. 1/2 npt(fbe)

Air Pressure Regulator Kit 210–613

300 psi (20 bar) Maximum Inlet Pressure

0-125 psi (0-8.75 bar) Regulated

Pressure Range

To regulate the air pressure to the gun. Includes gauge, air shutoff valve, and fittings. 1/4 npt(m)

Air Shutoff Valve 208–390

500 psi (35 bar) Maximum Working Pressure

To shutoff air supply line. 1/4 npt(m)

Gun Air Regulator Assy. 235–119

0–100 psi (0–7 bar) air regulator to control air to gun

SST Pressure Cup Kit 235–373 with single air regulator

1 qt (0.95 liter) capacity, 304 stainless steel cup. Includes a pressure relief valve and a single air regulator and gauge.

01727

0135

01725

SST Pressure Cup Kit 235–374 with double air regulator

1 qt (0.95 liter) capacity, 304 stainless steel cup. Includes a pressure relief valve, a 0–100 psi (0–7 bar) air regulator for gun atomization, and a 0–15 psi

(0–1.05 bar) air regulator for the 1 qt pressure cup supply air.

Accessories

01726

Disposable Polyethylene Cup Liners

Paint and solvent resistant. 40 liners per box.

112–490 1 Quart Cup Size

112–491 2 Quart Cup Size

2 Quart Pressure Cup 214–627

2 qt (1.94 liter) capacity, aluminum cup

Includes air pressure regulator and gauge, 4 ft (1.2 m) length air and fluid hose with 1/4 npsm(f) swivel ends, pressure relief valve, and rigid hook handle.

Gravity Cup Kit 236–038

7.5 oz (220 cc) capacity, 430 stainless steel cup, 3/8 npsm(f) fluid inlet

0125

1 Quart Pressure Cup Kit 224–426

1 qt (0.95 liter) capacity, aluminum cup

Some assembly required. Includes:

Part No.

Description

224–419 1 Quart Pressure Cup Assy., aluminum

(with check valve)

111–324 Female Connector, 1/8 npt x 5/32 tube

111–328 Male Connector, 10-32 x 5/32 tube

187–169 Tubing, 5/32” OD

Pressure Tank 171–226

2.5 gal (9.5 liter) capacity, aluminum tank. Includes air pressure regulator and gauge, pressure relief valve, pickup tube, and rigid hook handle.

0166

Husky 307 HVLP Systems

Includes Husky 307 Pump, Pail Cover, Air Regulators,

Suction Tube and Inlet Filter, Fluid Regulator, Fluid

Recirculation Line, HVLP Spray Gun, and Air and Fluid

Hoses

Part No.

Description

235–507 SST Pail Mount System

235–661 Carbon Steel Pail Mount System

0123

0122

1 Quart Remote SST

Pressure Cup 235–054

1 qt (0.95 liter) capacity, 304 stainless steel cup.

Includes air pressure regulator and gauge, 4 ft (1.2 m) length air and fluid hose with 1/4 npsm(f) swivel ends, pressure relief valve, and rigid hook handle.

01962

01526

Accessories

Low Pressure SST Pressure Tanks

For fluid pressures of 1 to 15 psi (0.70 to 1.05 bar)

High Pressure SST Pressure Tanks

For fluid pressures of 15 to 100 psi (1.05 to 7 bar)

Tank Size gallons (liters)

5 (19)

10 (38)

15 (57)

Low Pressure Tank

P/N

236–143

236–144

236–145

Low Pressure Tank with Agitator P/N

236–146

236–147

236–148

High Pressure Tank

P/N

236–149

236–150

236–151

High Pressure Tank with Agitator P/N

236–152

236–153

236–154

Low Pressure Tank

High Pressure Tank with Agitator

03084

Graco Phone

Numbers

TO PLACE AN ORDER , contact your Graco distributor, or call this number to identify the distributor closest to you: 1–800–328–0211 Toll Free

FOR TECHNICAL ASSIST ANCE, service repair information or assistance regarding the application of

Graco equipment: 1–800–543–0339 Toll Free

03189

Technical Data

Maximum Working Fluid Pressure

Maximum Working Air Pressure

. . . . .

. . . . . . .

100 psi (7 bar)

100 psi (7 bar)

Maximum Compliant Inbound

Air Pressure . . . . . . . . . . . . . . . . . . . . . . . 65 psi (4.5 bar)

Fluid & Air Temperature Range . . . . . .

Weight

Air Inlet

. . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . .

14.9 oz. (422 g)

1/4–18 npsm (R1/4–19) compound thread

Fluid Inlet . . . . . . . . . . . . . . . . .

32 F to 140 F

(0 C to 60 C)

3/8–18 npsm (R3/8–19) compound thread

Wetted Parts

Noise Data*

. . . . . . . . . . . 304 & 17–4 Stainless Steel

Sound Pressure at 65 psi (4.5 bar)

Sound Power at 65 psi (4.5 bar)

. . . . .

. . . . . .

95 Db(A)

101 Db(A)

* All readings were taken with the gun controls fully open at the assumed operator position. Sound pressure was tested to CAGI–PNUEROP–1969. Sound power was tested to ISO 3744–1981.

Dimensions

6.39 in.

(163 mm)

6.9 in.

(175 mm)

The Graco Warranty and Disclaimers

02018

WARRANTY

Graco warrants all equipment manufactured by it and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. As purchaser’s sole remedy for breach of this warranty, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment proven defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for, any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility with Graco equipment of structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claim. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor and transportation.

DISCLAIMERS AND LIMITATIONS

The terms of this warranty constitute purchaser’s sole and exclusive remedy and are in lieu of any other warranties (express or implied), including warranty of merchantability or warranty of fitness for a particular purpose , and of any non–contractual liabilities, including product liabilities, based on negligence or strict liability. Every form of liability for direct, special or consequential damages or loss is expressly excluded and denied. In no case shall Graco’s liability exceed the amount of the purchase price.

Any action for breach of warranty must be brought within two (2) years of the date of sale.

EQUIPMENT NOT COVERED BY GRACO WARRANTY

Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose , with respect to accessories, equipment, materials, or components sold but not manufactured by Graco. These items sold, but not manufactured by Graco (such as electric motor, switches, hose, etc.) are subject to the warranty, if any, of their manufacturer.

Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

Sales Offices: Atlanta, Chicago, Dallas, Detroit, Los Angeles, Mt. Arlington (N.J.)

Foreign Offices: Canada; England; Korea; Switzerland; France; Germany; Hong Kong; Japan

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

PRINTED IN U.S.A. 308–293 5/93 Revised 3/95

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement