MANUAL Vol.2 - Touchboards
ED-S3170/X3270/Vol.2/ENG 03.8.29 3:36 PM ページ 1
www.touchboards.com 205 Westwood Ave.Long Branch, NJ 07740 1-866-942-6273 [email protected]
USER'S MANUAL
Vol.2 (Extended)
Thank you for purchasing this projector.
WARNING • Please read the accompanying manual “SAFETY
INSTRUCTIONS” and this “USER'S MANUAL” thoroughly to ensure correct
usage through understanding. After reading, store this instruction manual in a
safe place for future reference.
ENGLISH
LCD Projector ED-S3170AT/ED-X3250AT/ED-X3280AT
NOTE • The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in this manual
• The reproduction, transmission or use of this document or contents is not permitted without express
written authority.
TRADEMARK ACKNOWLEDGEMENT :
• PS/2, VGA and XGA are registered trademarks of the International Business Machines Corporation.
• Apple, Mac and ADB are registered trademarks of Apple Computer, Inc.
• VESA and SVGA are trademarks of the Video Electronics Standard Association.
• Windows is a registered trademark of Microsoft Corporation.
• All other trademarks are the property of their respective owners.
CONTENTS
Page
MULTIFUNCTIONAL SETTINGS ........................................................................2
WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED ......7
SPECIFICATIONS .............................................................................................10
WARRANTY AND AFTER-SERVICE................................................................11
.......................................................................................
For "TECHNICAL" see the end of this manual.
www.touchboards.com 205 Westwood Ave.Long Branch, NJ 07740 1-866-942-6273
1
[email protected]
ED-S3170/X3270/Vol.2/ENG 03.8.29 3:36 PM ページ 2
MULTIFUNCTIONAL SETTINGS
This device has 6 separate menus: MAIN, PICTURE 1, PICTURE 2, INPUT,
SCREEN, OPTION. Each of these menus is operated using the same methods.
The basic operations of these menus are as follows.
Menu screen display : Press the "MENU" button.
Menu selection
: Choose a menu name using the
/
button, and press the
button or the ENTER button.
Item selection
: Choose an item using the
/
button, and press the
button or the ENTER button.
Return menu to last previous screen: Press the
button or the ESC button.
Execution of settings and/or adjustments: Operate by using the
/
button. (For further
details, read the explanation for each separate menu.)
Initialization of settings and/or adjustments: During operation, press the RESET button.
(Note that items whose functions are
performed simultaneously with the operation
of clock phase, language selection, automatic
adjustment, etc., cannot be initialized.)
End menu operations: Press the MENU button, or do not perform any operation for
several seconds.
MAIN Menu
With the MAIN menu, the seven items shown in the Table below can be
performed.
Perform each operation in accordance with the instructions in the Table.
Item
Adjust Brightness: Light
CONTRAST
Adjust Contrast: Strong
2
⇔
Dark
⇔
Weak
Select Aspect Ratio:
At RGB Input:
4:3
⇔
16:9
At VIDEO Input, S-VIDEO Input:
4:3
⇔
16:9
⇔
SMALL
• The SMALL picture may not be displayed correctly with certain input signals.
Select Picture Position (for 16:9/SMALL Picture):
TOP
⇔
CENTER
⇔
BOTTOM
GAMMA
Select Gamma Mode:
NORMAL
⇔
CINEMA
MIRROR
Select Mirror Status:
NORMAL
⇔
H:INVERT
LANGUAGE
12
: SELECT
Description
BRIGHT
PICT.POSIT.
BRIGHT
CONTRAST
ASPECT
PICT. POSIT.
GAMMA
MIRROR
LANGUAGE
Example : MAIN Menu
(BRIGHT)
MAIN Menu
ASPECT
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
⇔
⇔
DYNAMIC
V:INVERT
⇔
H&V:INVERT
Select Menu Language:
ENGLISH
⇔
FRANÇAIS
⇔
DEUTSCH
⇔
ESPAÑOL
⇔
ITALIANO
⇔
NORSK
⇔
NEDERLANDS
⇔
日本語
⇔
POTUGUÊS
⇔
中文
⇔
ED-S3170/X3270/Vol.2/ENG 03.8.29 3:36 PM ページ 3
With the PICTURE 1 menu, the five items shown in the Table
below can be performed.
Perform each operation in accordance with the instructions in the
Table.
COLOR BAL R
COLOR BAL B
SHARPNESS
COLOR
TINT
ENGLISH
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
PICTURE 1 Menu
12
: SELECT
Example : PICTURE1 Menu
(COLOR BAL R)
PICTURE1 Menu
Item
Description
COLOR BAL R
Adjust Red Color Balance: Dark
⇔
Light
COLOR BAL B
Adjust Blue Color Balance: Dark
⇔
Light
SHARPNESS
COLOR
TINT
⇔
Adjust Sharpness (for VIDEO/S-VIDEO): Clear
Soft
Adjust COLOR (for VIDEO/S-VIDEO):
Dark
⇔
Light
⇔
Adjust Tint (for VIDEO/S-VIDEO): Green
PICTURE 2 Menu
With the PICTURE 2 menu, the five items shown in the Table
below can be performed.
Perform each operation in accordance with the instructions in the
Table.
Red
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
V POSITION
H POSITION
H PHASE
H SIZE
OVER SCAN
12
: SELECT
Example : PICTURE2 Menu
(V POSITION)
PICTURE2 Menu
Item
Description
V POSITION
Adjust Vertical Position (for RGB): Up
H POSITION
Adjust Horizontal Position (for RGB): Left
H PHASE
⇔
Down
⇔
Right
Adjust Horizontal Phase (for RGB):
Right
⇔
Left
• Adjust to eliminate flicker.
H SIZE
Adjust Horizontal Size (for RGB): Large
⇔
Small
• If the horizontal size adjustment is excessive, the image may not be displayed
correctly. In such a case, initialize H SIZE with the RESET button.
OVER SCAN
Select Over-scan Ratio (for VIDEO/S-VIDEO):
LARGE
⇔
MIDDLE
⇔
SMALL
• It is recommended to select SMALL to avoid flicker at the lower part of the
picture.
3
ED-S3170/X3270/Vol.2/ENG 03.8.29 3:36 PM ページ 4
MULTIFUNCTIONAL SETTINGS (continued)
INPUT Menu
With the INPUT menu, the four items shown in the Table below can be
performed. With inputting of RGB IN 1 and RGB IN 2 signals, the
horizontal and vertical frequencies of the signals will be displayed on the
initial screen of the INPUT menu.
Perform each operation in accordance with the instructions in the Table.
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
AUTO
VIDEO
SYNC ON G
EXECUTE
: SELECT
Example : INPUT Menu
(AUTO)
INPUT Menu
4
Item
Description
AUTO
Auto Adjust (for RGB): Automatically adjusts H POSITION, V POSITION, H
PHASE, and H SIZE. Use this function with the maximum window size.
Auto Adjust (for VIDEO/S-VIDEO): Automatically selects the proper VIDEO
mode for the current input signal. This function is active only when the AUTO
mode is selected for the item VIDEO. Refer to the description for the item
VIDEO below.
• This function may not be available with a PAL60 signal and certain other
signals.
• The AUTO mode operation requires approximately 10 seconds.
VIDEO
Select Mode of Signal Type (for VIDEO/S-VIDEO):
AUTO
⇔
NTSC
⇔
PAL
⇔
SECAM
⇔
NTSC4.43
⇔
M-PAL
⇔
N-PAL
Selecting AUTO mode activates and performs the AUTO function for VIDEO/SVIDEO. It automatically selects the proper mode from among those above.
Use this function if the image becomes unstable with VIDEO/S-VIDEO. (e.g.
The image becomes irregular, or lacks color.)
• AUTO mode may not function correctly with a PAL60 signal and certain other
signals.
• The AUTO mode operation requires approximately 10 seconds.
SYNC ON G
On/Off SYNC ON G Mode:
TURN ON
⇔
TURN OFF
Selecting TURN ON turns on the SYNC ON G mode. The SYNC ON G mode
allows reception of SYNC on G.
• In the SYNC ON G mode, the picture may be distorted with certain input
signals. In such a case, remove the signal connector so that no signal is
received and turn SYNC ON G off, and then reconnect the signal.
ED-S3170/X3270/Vol.2/ENG 03.8.29 3:36 PM ページ 5
With the SCREEN menu, the five items shown in the Table below can be performed.
Please perform each operation in accordance with the instructions in the Table.
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
BLANK
START UP
MyScreen
MyScreen Size
MyScreen Lock
MyScreen
ORIGNAL
ENGLISH
SCREEN Menu
: SELECT
Example : SCREEN Menu
(BLANK)
SCREEN Menu
Item
Description
BLANK
Selection of BLANK Screen:
MyScreen
⇔
ORIGINAL
⇔
. .
⇔
.
.
⇔
. .
The BLANK Screen may be voluntarily selected. The BLANK Screen is displayed when the screen
has been erased (i.e., made to vanish) by manipulating the BLANK button (please refer to the
“Temporarily Blanking the Screen” section of the separate booklet, Vol. 1 (Basic)).
MyScreen: Using the MyScreen category (see this Table, below), one can register a desired screen
(or screens). At the time of factory shipment, this is set as a non-patterned (plain) blue color screen.
ORIGINAL: Existing standard screens. Please make confirmation using the actual screen(s).
Option screens: Various colored non-patterned (plain) screens displayed within the Menus.
• The MyScreen and the ORIGINAL Screen will each change to a non-patterned (plain) black color
screen several minutes after being displayed.
START UP
Selection of START UP Screen:
MyScreen
⇔
ORIGINAL
⇔
TURN OFF
The START UP Screen may be voluntarily selected. The START UP Screen is displayed when
no signal has been inputted, or when spec signals are being inputted.
MyScreen: Using the MyScreen category (see this Table, below), one can register a desired screen
(or screens). At the time of factory shipment, this is set as a non-patterned (plain) blue color screen.
ORIGINAL: Existing standard screens. Please make confirmation using the actual screen(s).
TURN OFF: A non-patterned (plain) blue color screen.
• The MyScreen and ORIGINAL screens will switch to the BLANK screen (see above in this
table) a few minutes after being displayed. If the BLANK screen is the MyScreen or
ORIGINAL screen, it will turn immediately to a solid black screen.
MyScreen
Registration of MyScreen:
When this item is executed, the MyScreen Menu for registration of MyScreen for the BLANK Screen
and the START UP Screen is displayed. When operations are performed in accordance with this Menu,
one can “cut” and register desired screens from among the received images within the display.
1. After the “Do you start capturing this picture?” message has been displayed, pressing the ESC (or
RESET) button interrupts execution of the MyScreen. When the ENTER button is pressed, the
picture becomes static (no longer moves), and a frame for picture cutting, as well as the message
that follows below, appear. Please press the button when the screen you want to register is
currently being displayed.
2. When the “Move the capture area as you want.” message has been displayed, pressing the ESC (or RESET)
button will eliminate the static state of the picture, and operations can be performed again from operation 1.
The frame can be moved using the
,
,
,
buttons. After designating the screen
you want to register, pressing the ENTER button will initiate screen registration. The registration
process takes approximately 1 minute to complete.
3. When the registration has been completed, the screen of the registered MyScreen, plus the
message, “MyScreen registration is finished,” will be displayed for several seconds, after which
the operation is terminated.
MyScreen Size
Selection of MyScreen display size:
x1
⇔
FULL
MyScreen Lock
Invalidation of MyScreen registration function:
TURN ON
⇔
TURN OFF
When TURN ON is selected, the MyScreen category (see this Table, above) cannot be executed; in
this way, one can prohibit rewrites (“writeovers”) of the MyScreen.
5
ED-S3170/X3270/Vol.2/ENG 03.8.29 3:36 PM ページ 6
MULTIFUNCTIONAL SETTINGS (continued)
OPTION Menu
With the OPTION menu, the five items shown in the Table below
can be performed.
Please perform each operation in accordance with the instructions
in the Table.
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
VOLUME
AUTO OFF
WHISPER
LAMP TIME
FILTER TIME
12
: SELECT
Example : OPTION Menu
(VOLUME)
OPTION Menu
Item
VOLUME
6
Description
Adjust Volume: High
⇔
Low
AUTO OFF
Adjust AUTO OFF Time:
Long (MAX. 99 min.)
⇔
Short (Min. 1 min.)
⇔
(DISABLE: 0 min.)
The system automatically enters the standby mode if no signal is received
within the set time. This function is inactive when DISABLE (0 min.) is selected.
WHISPER
Select WHISPER Mode:
NORMAL
⇔
WHISPER
When WHISPER is selected the WHISPER mode is activated. In the WHISPER
mode, acoustic noise and screen brightness are reduced.
LAMP TIME
Refer to LAMP TIME: When set, this function displays the total time the
projector lamp has been used since new.
Reset LAMP TIME [Use this function only when the lamp has been replaced!]:
Depress the RESET button for at least 3 seconds while lamp time is being
displayed. The reset menu will then appear. After you replace the lamp with a
new lamp, select RESET on the menu with the
button.
• Do not reset the lamp time unless you have replaced the lamp. And, always
reset the lamp time when replacing the lamp. The message functions will not
operate properly if the lamp time is not reset correctly.
• Before replacing the lamp, carefully read the descriptions headed "THE
LAMP".
FILTER TIME
Refer to FILTER TIME: This function displays the total time the air-filter has
been used since new.
Reset FILTER TIME [Use this function only when the filter is cleaned or replaced!]:
Depress the RESET button for at least 3 seconds while filter time is being
displayed. The reset menu will then appear. After you replace the filter, select
RESET on the menu with the
button.
• Do not reset the filter time unless you have cleaned or replaced the filter. And,
always reset the filter time when cleaning or replacing the filter. The message
functions will not operate properly if the filter time is not reset correctly.
• Before cleaning or replacing the filter, carefully read the descriptions headed "THE AIR FILTER".
ED-S3170/X3270/Vol.2/ENG 03.8.29 3:36 PM ページ 7
ENGLISH
WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED
Related Messages
When the unit's power is ON, messages such as those shown below may be displayed. When
any such message is displayed on the screen, please respond as described below.
Message
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
(Note 1)
Description
Lamp usage time is approaching 2,000 hours. (Note 2)
Preparation of a new lamp, and an early lamp change, is
recommended. After you have changed the lamp, please be
sure to reset the lamp timer.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
THE POWER WILL TURN OFF
AFTER ** hr.
(Note 1)
Lamp usage time is approaching 2,000 hours. A lamp change
within ** hours is recommended. (Note 2)
When lamp usage reaches 2,000 hours, the power will
automatically be turned OFF. Please change the lamp by
referring to “THE LAMP” in Vol.1 (Basic). After you have
changed the lamp, please be sure to reset the lamp
timer.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
THE POWER WILL TURN OFF
AFTER 0 hr.
As lamp use has reached 2,000 hours, the power will soon be
automatically turned OFF. (Note 2)
Please immediately turn the power OFF, and follow the
instructions in the “THE LAMP” section of the separate booklet,
Vol.1 (Basic).
After you have changed the lamp, please be sure to reset the
lamp timer.
CLEAN THE AIR FILTER
AFTER CLEANING AIR FILTER,
RESET THE FILTER TIMER.
NO INPUT IS DETECTED
ON ***
A note of precaution when cleaning the air filter.
After cleaning the filter, operate FILTER TIME of the OPTION
Menu, and perform reset of the filter timer.
There is no input signal.
Please confirm the signal input connection, and the status of the
signal source.
The horizontal or vertical wavelength of the inputted signal is
SYNC IS OUT OF RANGE
outside of the response parameters of this unit. Please confirm
ON *** fH *****kHz fV *****Hz the specs for this unit or the signal source specs.
The internal portion temperature is rising. Please turn the power
OFF, and allow the unit to cool down for approximately 20
minutes. After having confirmed the following items, then please
CHECK THE AIR FLOW
resent the power to ON.
• Is there blockage of the air passage aperture?
• Is the air filter dirty?
• Does the peripheral temperature exceed 35°C?
NOTES
Note 1: Although this message will be automatically disappeared after around 3 minutes, it will be
reappeared every time the power is turned ON.
Note 2: Lamps have a finite product life. Lamps are characterized by the fact that, after long hours of
usage, a lamp will no longer light up, or the lamp will break or burst, etc. This unit is equipped
with an automatic shut-down function, such that the power will automatically be turned OFF
when lamp usage time has reached 2,000 hours. Please be aware, however, that among lamp
types, there are major differences in product lifetimes; a lamp may thus fail to light even prior
to the functioning of the automatic shut-down function of this unit.
7
ED-S3170/X3270/Vol.2/ENG 03.8.29 3:36 PM ページ 8
Regarding the Indicator Lamps
Lighting and flashing of the POWER indicator, the LAMP indicator, and the
TEMP indicator have the meanings as described in the Table below.
Please respond in accordance with the instructions within the Table.
POWER
indicator
LAMP
indicator
TEMP
indicator
The orange Turned OFF Turned OFF
lamp is lighted (Not lighted) (Not lighted)
Description
The STANDBY mode is set
Flashing of the green lamp
Turned OFF
Turned OFF
The unit is warming up. Please wait.
The green lamp is lighted
Turned OFF
Turned OFF
The unit is in an ON state. Ordinary operations may be performed.
Flashing of the orange lamp
Turned OFF
Turned OFF
Blinking of the
red lamp
-
-
The red lamp
Turned
OFF
The unit is cooling down. Please wait.
The unit is cooling down. Please wait.
A certain error has been detected. Wait until the POWER indicator lamp has finished
flashing, and then perform the proper response measure using the item descriptions
below as reference.
The lamp does not light.
There is a possibility that the interior portion has become heated. Turn the power OFF and wait
approximately 20 minutes. After the main unit has cooled down, please confirm whether or not
there is blockage of the air passage aperture, whether or not the filter is dirty, and/or whether or
not the peripheral temperature exceeds 35°C, etc. After performing any needed maintenance,
turn the power ON again; if the same display is displayed, then please change the lamp.
The red lamp
is lighted, or
blinks
The red lamp
is lighted, or
blinks
The red lamp
is lighted, or
blinks
The red lamp is
lighted, or
blinks
The green lamp
is lighted
The green
lamp is lighted
is lighted
Blinking of the
red lamp
Turned
OFF
Either there is no lamp and/or lamp cover, or either of these has not been properly fixed
(attached). Turn the power OFF and wait approximately 45 minutes. After the main unit has
sufficiently cooled down, please make confirmation of the attachment state of the lamp and
lamp cover. After performing any needed maintenance, turn the power ON again; if the same
display is displayed, then please contact a sales store or a service company.
The cooling fan is not operating. Turn the power OFF and wait approximately 20 minutes. After the
main unit has cooled down, please make confirmation that no foreign matter has become caught in
the fan, etc. After performing any needed maintenance, turn the power ON again; if the same display
red lamp
is displayed, then please contact a sales store or a service company.
There is a possibility that the interior portion has become heated. Turn the power OFF and wait
approximately 20 minutes. After the main unit has cooled down, please confirm whether or not
Turned The red lamp is there is blockage of the air passage aperture, whether or not the filter is dirty, and/or whether or
not the peripheral temperature exceeds 35°C, etc. After performing any needed maintenance,
lighted
OFF
turn the power ON again; if the same display is displayed, then please contact a sales store or a
service company.
There is a possibility that the interior portion has become overcooled. Please use the unit within
Alternative blinking
the usage temperature parameters (0°C to 35°C). After performing any needed maintenance,
turn the power ON again; if the same display is displayed, then please contact a sales store or a
with the red lamp
service company.
Turned
OFF
Blinking of the
Simultaneous blinking
with the red lamp
This is a notification that it is time to clean the filter.
After cleaning the filter, operate the FILTER TIME portion of the OPTION Menu, and perform
reset of the FILTER TIME.
NOTE
When the interior portion has become overheated, for safety purposes, the power source is automatically turned OFF,
and the indicator lamps may also be turned OFF. Press the “ ○” (power OFF) side of the main power switch, and wait
for approximately 20 minutes. Please then use the unit only after having first confirmed that the unit has sufficiently
cooled down.
8
ED-S3170/X3270/Vol.2/ENG 03.8.29 3:36 PM ページ 9
ENGLISH
WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED (continued)
Phenomena That May Easily Be Mistaken for Machine Defects
Before requesting repair, check in accordance with the following chart.
If the situation cannot be corrected, then contact your dealer.
Phenomenon
Power does not
come ON
No sound or
pictures are
outputted
Pictures are
displayed, but no
sounds are heard
Sounds are
heard, but no
pictures are
displayed
Colors have a fadedout appearance
Color tone is poor
Pictures appear
dark
Pictures appear
blurry
Cases not involving a machine defect
Items to be confirmed
Reference
Page(s)
The main power source is not ON.
Turn on the main power.
The electrical power cord is not plugged in.
The input changeover settings
are mismatched.
Correctly connect the power cord.
Be sure to press the “O” (power OFF) side
of the main power switch, and leave this OFF
for approximately 20 minutes. After the unit Vol.1-14
has sufficiently cooled down, turn ON the
power source.
Select the input signal, and
Vol.1-15
correct the settings.
No signal is being inputted.
Correctly connect the connection cord.
Vol.1-10, 11
The electrical wiring to this unit
is not correctly connected.
Correctly connect the connection cord.
Vol.1-10, 11
The volume setting has been set at (or
adjusted to) an extremely low level.
Adjust the VOLUME setting to a higher level.
Vol.1-17
The MUTE mode is the current setting.
Press the MUTE button to release
Vol.1-17
(change) the MUTE mode setting.
The electrical wiring to this unit
is not correctly connected.
Correctly connect the connection cord.
Vol.1-10, 11
The brightness setting has been set at
(or adjusted to) an extremely low level.
Adjust the BRIGHT setting to a
brighter level.
Vol.2-2
The lens cap has not been removed.
Remove the lens cap.
Vol.1-14
Color depth setting or color tone setting
Perform picture adjustments by changing the
COLOR BAL R, the COLOR BAL B, and/or the Vol.2-3
TINT settings, etc.
The brightness setting and/or contrast
setting has not been properly adjusted.
Perform picture adjustments by changing the
Vol.2-2
BRIGHT and/or CONTRAST settings, etc.
The WHISPER mode is the current
setting.
Change (by releasing) from the
Vol.2-6
WHISPER mode.
Lamp is approaching the end of its
product lifetime.
Exchange the old lamp with a new
Vol.1-25, 26
lamp.
Either the FOCUS setting or the H
PHASE is not properly adjusted.
Adjust the FOCUS and H PHASE settings.
The main power source has been
interrupted during operation, such as by
a power outage (blackout), etc.
Vol.1-3, 14
Vol.1-15
Vol.2-3
NOTE
Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and
such do not constitute or imply a machine defect.
9
ED-S3170/X3270/Vol.2/ENG 03.8.29 3:36 PM ページ 10
SPECIFICATIONS
NOTE • This specifications are subject to change without notice.
Item
Product name
Panel size
Liquid
crystal
panel
Specification
Liquid crystal projector
1.8 cm (0.7 type)
Drive system
TFT active matrix
Pixels
ED-S3170AT:480,000 pixels (800 horizontal x600 vertical)
ED-X3250AT/ED-X3280AT:786,432 pixels (1024 horizontal x768 vertical)
Lens
Zoom lens F=1.7 ~ 1.9 f=21.7 ~ 26.1 mm
Lamp
150 W UHB
Speaker
1.0W
Power supply
AC100 ~ 120V, 2.7A / AC220 ~ 240V, 1.3A
Power consumption
240W
Temperature range
0 ~ 35°C (Operating)
Size
295 (W) x 87.5 (H) x237 (D) mm
Weight (mass)
2.7 kg
Ports
RGB Ports
RGB IN(1, 2) ..................2
VIDEO Ports
VIDEO IN ........................1
S-VIDEO IN ....................1
AUDIO Ports
AUDIO IN(1,2) ................2
AUDIO IN(R, L) ..............1
Optional Parts
RGB OUT Ports
RGB OUT........................1
AUDIO OUT Ports
AUDIO OUT ....................1
CONTROL Ports
CONTROL ......................1
USB ................................1
Lamp: ED-S3170AT/ED-X3280AT=DT00511
ED-X3250AT=DT00521
Air Filter: MU01691
* For others, consult your dealer.
Dimension Diagram
231
237
295
10
50.5
87.5
37
77.5
Unit : mm
WARRANTY AND AFTER-SERVICE
If a problem occurs with the equipment, first refer to the 7 “WHAT TO DO WHEN YOU
THINK A MACHINE DEFECT HAS OCCURRED” section and run through the suggested
checks. If this does not resolve the problem contact your dealer or service company. They
will tell you what warranty condition is applied.
ENGLISH
ED-S3170/X3270/Vol.2/ENG 03.8.29 3:36 PM ページ 11
11
ED-S3170/X3270/TECHNICAl 03.8.29 3:39 PM ページ 1
TECHNICAL
SIGNAL CONNECTOR PIN ASSIGNMENT
RGB IN [1]/[2]
RGB OUT
S-VIDEO
D-sub 15-pin Shrink
Pin No
Signal
Mini Din 4-pin
Pin No
Signal
1
Video input Red
9
-
2
3
4
5
6
7
8
Video input Green
Video input Blue
Ground
Ground Red
Ground Green
Ground Blue
10
11
12
13
14
15
Ground
RGB IN [1]: SDA (DDC)
RGB IN [2]:
RGB OUT :
H. sync./ Composite sync.
Vertical sync
RGB IN [1]: SCL (DDC)
RGB IN [2]:
RGB OUT :
signal
Terminal
RGB IN(1、2)
RGB signal
input
AUDIO IN 1
Mini Din 4-pin
Pin No Signal
1
2
Color:
0.286Vp-p (NTSC, burst signal),
75Ω terminator
0.3Vp-p (PAL/SECAM, burst signal),
75Ω terminator
Brightness:
1.0Vp-p, 75Ω terminator
3
Ground
4
Ground
-
Specification
Video: Analog 0.7Vp-p, 75Ω terminator (positive)
H/V. sync.: TTL level (positive/negative)
Composite sync.: TTL level
D-sub 15-pin shrink jack
200mVrms,50kΩ (max.3.Ovp-p)
Stereo mini jack
AUDIO IN 2
Video signal
input
S-VIDEO IN
AUDIO IN(R、L)
RGB OUT
Signal output
AUDIO OUT
1.0Vp-p, 75Ω terminator, RCA jack
Brightness signal: 1.0Vp-p, 75Ω terminator
Color signal: 0.286Vp-p (NTSC, burst signal),75Ω terminator
0.300Vp-p (PAL/SECAM, burst signal),75Ω terminator
Mini DIN 4-pin jack
200mVrms, 50 kΩ (max. 3.0Vp-p)
RCA jack
TECHNICAL
VIDEO IN
Video: Analog 0.7Vp-p, 75Ω output impedance (positive)
H/V. sync.: TTL level (positive/negative)
Composite sync.: TTL level
D-sub 15-pin shrink jack
200mVrms, out put impedance1kΩ (max.3.Ovp-p)
Stereo mini jack
1
ED-S3170/X3270/TECHNICAl 03.8.29 3:39 PM ページ 2
EXAMPLE OF COMPUTER SIGNAL
Resolution
H×V
fH (kHz)
fV (Hz)
Rating
720 × 400
37.9
85.0
VESA
640 × 480
31.5
59.9
VESA
640 × 480
35.0
66.7
640 × 480
37.9
72.8
VESA
640 × 480
37.5
75.0
VESA
640 × 480
43.3
85.0
800 × 600
35.2
56.3
800 × 600
37.9
800 × 600
48.1
800 × 600
Signal mode
Display mode
ED-S3170AT
ED-X3250AT
ED-X3280AT
TEXT
Zoom in
Zoom in
VGA (60Hz)
Zoom in
Zoom in
Mac13"mode
Zoom in
Zoom in
VGA (72Hz)
Zoom in
Zoom in
VGA (75Hz)
Zoom in
Zoom in
VESA
VGA (85Hz)
Zoom in
Zoom in
VESA
SVGA (56Hz)
Zoom in
60.3
VESA
SVGA (60Hz)
Zoom in
72.2
VESA
SVGA (72Hz)
Zoom in
46.9
75.0
VESA
SVGA (75Hz)
Zoom in
800 × 600
53.7
85.1
VESA
SVGA (85Hz)
832 × 624
49.7
74.5
1024 × 768
48.4
60.0
1024 × 768
56.5
70.1
1024 × 768
60.0
1024 × 768
1152 × 864
Zoom in
Mac16"mode
Zoom out
Zoom in
VESA
XGA (60Hz)
Zoom out
VESA
XGA (70Hz)
Zoom out
75.0
VESA
XGA (75Hz)
Zoom out
68.7
85.0
VESA
XGA (85Hz)
Zoom out
67.5
75.0
VESA
SXGA (75Hz)
Zoom out
Zoom out
1280 × 960
60.0
60.0
VESA
SXGA (60Hz)
Zoom out
Zoom out
1280 × 1024
64.0
60.0
VESA
SXGA (60Hz)
Zoom out
Zoom out
1280 × 1024
80.0
75.0
VESA
SXGA (75Hz)
Zoom out
Zoom out
1280 × 1024
91.2
85.0
VESA
SXGA (85Hz)
Zoom out
Zoom out
1600 × 1200
75.0
60.0
VESA
UXGA (60Hz)
Zoom out
Zoom out
NOTE • Some computers may have multiple display screen modes. Use of some
of these modes will not be possible with this projector.
• Be sure to check jack type, signal level, timing and resolution before connecting this
projector to a computer.
• Depending on the input signal, full-size display may not be possible in some cases.
Refer to the number of display pixels above.
• This projector will display up to UXGA (1600X1200) resolution signals but the image
will be rescaled to the native resolution of the projector. Best display performance is
achieved when the signal input resolution is the same as the native resolution of the
projector.
• The image may not be displayed correctly when the input sync. signal is “Composite
Sync.” or “Sync. on G”.
2
ED-S3170/X3270/TECHNICAl 03.8.29 3:39 PM ページ 3
INITIAL SET SIGNALS
The following signals are used for the initial settings.
The signal timing of some computer models may be different. In such case, refer to
adjust the V.POSIT and H.POSIT of the menu.
Back porch b
Front porch d
Display interval c
Back porch b
Front porch d
Display interval c
DATA
DATA
HSYNC
VSYNC
Sync a
Horizontal signal timing (µs)
TEXT
a
2.0
b
3.0
c
20.3
d
1.0
Computer /
Signal
Vertical signal timimg (lines)
TEXT
a
3
b
42
c
400
d
1
VGA (60Hz)
3.8
1.9
25.4
0.6
VGA (60Hz)
2
33
480
10
Mac 13"mode
2.1
3.2
21.2
2.1
Mac 13"mode
3
39
480
3
VGA (72Hz)
1.3
3.8
20.3
1.0
VGA (72Hz)
3
28
480
9
VGA (75Hz)
2.0
3.8
20.3
0.5
VGA (75Hz)
3
16
480
1
VGA (85Hz)
1.6
2.2
17.8
1.6
VGA (85Hz)
3
25
480
1
SVGA (56Hz)
2.0
3.6
22.2
0.7
SVGA (56Hz)
2
22
600
1
SVGA (60Hz)
3.2
2.2
20.0
1.0
SVGA (60Hz)
4
23
600
1
SVGA (72Hz)
2.4
1.3
16.0
1.1
SVGA (72Hz)
6
23
600
37
SVGA (75Hz)
1.6
3.2
16.2
0.3
SVGA (75Hz)
3
21
600
1
SVGA (85Hz)
1.1
2.7
14.2
0.6
SVGA (85Hz)
3
27
600
1
Mac 16"mode
1.1
3.9
14.5
0.6
Mac 16"mode
3
39
624
1
XGA (60Hz)
2.1
2.5
15.8
0.4
XGA (60Hz)
6
29
768
3
XGA (70Hz)
1.8
1.9
13.7
0.3
XGA (70Hz)
6
29
768
3
XGA (75Hz)
1.2
2.2
13.0
0.2
XGA (75Hz)
3
28
768
1
XGA (85Hz)
1.0
2.2
10.8
0.5
XGA (85Hz)
3
36
768
1
1152×864 (75Hz)
1.2
2.4
10.7
0.6
1152×864 (75Hz)
3
32
864
1
1280×960 (60Hz)
1.0
2.9
11.9
0.9
1280×960 (60Hz)
3
36
960
1
1280×1024 (60Hz)
1.0
2.3
11.9
0.4
1280×1024 (60Hz)
3
38
1024
1
1280×1024 (75Hz)
1.1
1.8
9.5
0.2
1280×1024 (75Hz)
3
37
1024
2
1280×1024 (85Hz)
1.0
1.4
8.1
0.4
1280×1024 (85Hz)
3
44
1024
1
1600×1200 (60Hz)
1.2
1.9
9.9
0.4
1600×1200 (60Hz)
3
46
1200
1
TECHNICAL
Computer /
Signal
Sync a
3
ED-S3170/X3270/TECHNICAl 03.8.29 3:39 PM ページ 4
CONNECTION TO THE MOUSE CONTROL
Projector
ADB Mouse
DATA
CONTROL Terminal
D-sub 15-pin shrink jack
RTS
2 3 4 5
6 7 8 9 10
11 12 13 14 15
1
+5V
GND
Serial Mouse
1
2
3
4
SEL0
RTS
D-sub 15-pin shrink jack
1 2 3 4 5
7 8 9 10
11 12 13 14 15
GND
TD
ADB
(POWER ON)
+5V
GND
Mouse jack
Mini DIN 4-pin
3
4
1
2
Projector
CONTROL Terminal
6
Computer
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Computer
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
CD
RD
TD
DTR
GND
DSR
RTS
CTS
RI
1
2
3
4
5
6
7
8
9
Mouse jack
D-sub 9-pin
1
2
6
3
5
4
8
7
9
USB Mouse
USB jack
(B type)
2
3
Computer
Projector
+5V 1
1
1
—DATA 2
2 —DATA
+DATA 3
3
GND 4
4
+5V
USB jack
(A type)
+DATA
1
4 GND
2
3
4
USB cable
PS/2 Mouse
CONTROL Terminal
CLK
DATA
D-sub 15-pin shrink jack
SEL0
RTS
2 3 4 5
7 8 9 10
11 12 13 14 15
+5V
GND
6
4
Projector
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Computer
1
2
3
4
5
6
DATA
GND
+5V
CLK
Mouse jack
Mini DIN 6-pin
6
5
3
4
2
1
ED-S3170/X3270/TECHNICAl 03.8.29 3:39 PM ページ 5
RS-232C COMMUNICATION
(1) Turn off the projector and computer power supplies and connect with the RS-232C cable.
(2) Turn on the computer power supply and after the computer has started up, turn on the
projector power supply.
Projector
Control jack
D-sub 15-pin shrink jack
Computer
1
2
3
4
5
SELO 6
RTS 7
8
9
GND 10
11
12
RD 13
TD 14
15
1
2
3
4
5
6
7
8
9
CD
RD
TD
DTR
GND
DSR
RTS
DTS
RI
RS-232C jack
D-sub 9-pin
2
1
6
3
7
4
8
5
9
Communications setting
19200bps, 8N1
1 Protocol
Consist of header (7 bytes) + command data (6 bytes).
2 Header
BE + EF + 03 + 06 + 00 + CRC_low + CRC_high
CRC_low : Lower byte of CRC flag for command data.
CRC_high : Upper byte of CRC flag for command data.
3 Command data
Command data chart
byte_0
byte_1
byte_2
Action
low
byte_3
Type
high
low
byte_4
byte_5
Setting code
high
low
high
Action (byte_0 - 1)
Classification
Content
1
SET
Change setting to desired value.
2
GET
Read projector internal setup value.
4
INCREMENT
Increment setup value by 1.
5
DECREMENT
Decrement setup value by 1.
6
EXECUTE
Run a command.
TECHNICAL
Action
5
ED-S3170/X3270/TECHNICAl 03.8.29 3:39 PM ページ 6
RS-232C COMMUNICATION (continued)
Requesting projector status (Get command)
(1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes)
+‘00H’+‘00H’) from the computer to the projector.
(2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.
Changing the projector settings (Set command)
(1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) +
setting code (2 bytes)) from the computer to the projector.
(2) The projector changes the setting based on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
Using the projector default settings (Reset Command)
(1) The computer sends the default setting code Header + Command data (‘06H’+‘00H’+
type (2 bytes) +‘00H’+‘00H’) to the projector.
(2) The projector changes the specified setting to the default value.
(3) The projector returns the response code ‘06H’ to the computer.
Increasing the projector setting value (Increment command)
(1) The computer sends the increment code Header + Command data (‘04H’+‘00H’+
type (2 bytes) +‘00H’+‘00H’) to the projector.
(2) The projector in creases the setting value on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
Decreasing the projector setting value (Decrement command)
(1) The computer sends the decrement code Header + Command data (‘05H’+‘00H’+
type (2 bytes) +‘00H’ + ‘00H’) to the projector.
(2) The projector decreases the setting value on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
When a command sent by the projector cannot be understood by the computer
When the command sent by the projector cannot be understood, the error command ‘15H’ is
returned by the computer. Some times, the projector ignores RS-232C commands during
other works. If the error command ‘15H’ is returned, please send the same command again.
When data sent by the projector cannot be practice
When the command sent by the projector cannot be practiced, the the error code ‘1cH’
+‘xxxxH’ is returned.
When the data length is greater than indicated by the data length code, the projector will
ignore the excess data code.
Conversely, when the data length is shorter than indicated by the data length code, an
error code will be returned to the projector.
NOTE • Operation cannot be guaranteed when the projector receives an
undefined command or data.
• Provide an interval of at least 40ms between the response code and any other code.
• The projector outputs test data when the power supply is switched ON, and when the
lamp is lit. Ignore this data.
• Commands are not accepted during warm-up.
6
ED-S3170/X3270/TECHNICAl 03.8.29 3:39 PM ページ 7
Command data chart
Blank Color
Mirror
Operation type
Set
Set
Type
Setting code
Blue
BE EF
03
06 00
CB D3
01 00
00 30
03 00
White
BE EF
03
06 00
6B D0
01 00
00 30
05 00
Black
BE EF
03
06 00
9B D0
01 00
00 30
06 00
MyScreen
BE EF
03
06 00
FB CA
01 00
00 30
20 00
ORIGNAL
BE EF
03
06 00
FB E2
01 00
00 30
40 00
Get
BE EF
03
06 00
08 D3
02 00
00 30
00 00
Normal
BE EF
03
06 00
C7 D2
01 00
01 30
00 00
H Inverse
BE EF
03
06 00
57 D3
01 00
01 30
01 00
V lnverse
BE EF
03
06 00
A7 D3
01 00
01 30
02 00
H&V Inverse
BE EF
03
06 00
37 D2
01 00
01 30
03 00
BE EF
03
06 00
F4 D2
02 00
01 30
00 00
Normal
BE EF
03
06 00
83 D2
01 00
02 30
00 00
Freeze
BE EF
03
06 00
13 D3
01 00
02 30
01 00
Get
BE EF
03
06 00
B0 D2
02 00
02 30
00 00
ORIGNAL
BE EF
03
06 00
0B D2
01 00
04 30
00 00
OFF
BE EF
03
06 00
9B D3
01 00
04 30
01 00
MyScreen
BE EF
03
06 00
CB CB
01 00
04 30
20 00
Get
BE EF
03
06 00
38 D2
02 00
04 30
00 00
English
BE EF
03
06 00
F7 D3
01 00
05 30
00 00
Français
BE EF
03
06 00
67 D2
01 00
05 30
01 00
Deutsch
BE EF
03
06 00
97 D2
01 00
05 30
02 00
Español
BE EF
03
06 00
07 D3
01 00
05 30
03 00
Italiano
BE EF
03
06 00
37 D1
01 00
05 30
04 00
Norsk
BE EF
03
06 00
A7 D0
01 00
05 30
05 00
Nederlands
BE EF
03
06 00
57 D0
01 00
05 30
06 00
Português
BE EF
03
06 00
C7 D1
01 00
05 30
07 00
日本語
BE EF
03
06 00
37 D4
01 00
05 30
08 00
中文
BE EF
03
06 00
A7 D5
01 00
05 30
09 00
Get
Freeze
Startup
Language
Magnify
Set
Set
Set
Command data
Header
CRC
Action
BE EF
03
06 00
57 D5
01 00
05 30
0A 00
Get
BE EF
03
06 00
C4 D3
02 00
05 30
00 00
Get
BE EF
03
06 00
7C D2
02 00
07 30
00 00
Increment
BE EF
03
06 00
1A D2
04 00
07 30
00 00
Decrement
BE EF
03
06 00
CB D3
05 00
07 30
00 00
Get
BE EF
03
06 00
08 86
02 00
10 31
00 00
Increment
BE EF
03
06 00
6E 86
04 00
10 31
00 00
Decrement
BE EF
03
06 00
BF 87
05 00
10 31
00 00
Brightness
Reset
Execute
BE EF
03
06 00
58 D3
06 00
00 70
00 00
Contrast Reset
Execute
BE EF
03
06 00
A4 D2
06 00
01 70
00 00
V.Position
Reset
Execute
BE EF
03
06 00
E0 D2
06 00
02 70
00 00
Auto off
TECHNICAL
Names
7
ED-S3170/X3270/TECHNICAl 03.8.29 3:39 PM ページ 8
Command data chart (continued)
Names
Operation type
H.Position Reset
Execute
BE EF
03
H.Size Reset
Execute
BE EF
Color Balance
R Reset
Execute
Color Balance
B Reset
Command data
Header
CRC
Action
Type
Setting code
06 00
IC D3
06 00
03 70
00 00
03
06 00
68 D2
06 00
04 70
00 00
BE EF
03
06 00
94 D3
06 00
05 70
00 00
Execute
BE EF
03
06 00
D0 D3
06 00
06 70
00 00
Sharpness Reset
Execute
BE EF
03
06 00
C4 D0
06 00
09 70
00 00
Color Reset
Execute
BE EF
03
06 00
80 D0
06 00
0A 70
00 00
Tint Reset
Execute
BE EF
03
06 00
7C D1
06 00
0B 70
00 00
Keystone_V Reset
Execute
BE EF
03
06 00
08 D0
06 00
0C 70
00 00
Keystone_H Reset
Execute
BE EF
03
06 00
98 D8
06 00
20 70
00 00
Auto Adjust
Execute
BE EF
03
06 00
91 D0
06 00
0A 20
00 00
Lamp Time Reset
Execute
BE EF
03
06 00
58 DC
06 00
30 70
00 00
Filter Time Reset
Execute
BE EF
03
06 00
98 C6
06 00
40 70
00 00
off
BE EF
03
06 00
FB D8
01 00
20 30
00 00
on
BE EF
03
06 00
6B D9
01 00
20 30
01 00
BE EF
03
06 00
C8 D8
02 00
20 30
00 00
BE EF
03
06 00
D9 D8
02 00
20 60
00 00
Blank on/off
Set
Get
Error Status
Get
(Example of Return)
00 00
01 00
(Normal) (Cover-error)
04 00
05 00
(Temp-error) (Air flow-error)
Power
06 00
(Lamp-Time-over)
03 00
(Lamp-error)
07 00
(Cool-error)
08 00
(Filter-Error)
BE EF
BE EF
BE EF
03
03
03
06 00
06 00
06 00
2A D3
BA D2
19 D3
01 00
01 00
02 00
00 60
00 60
00 60
00 00
01 00
00 00
RGB1
BE EF
03
06 00
FE D2
01 00
00 20
00 00
RGB2
BE EF
03
06 00
3E D0
01 00
00 20
04 00
Video
BE EF
03
06 00
6E D3
01 00
00 20
01 00
SVideo
BE EF
03
06 00
9E D3
01 00
00 20
02 00
Get
BE EF
03
06 00
CD D2
02 00
00 20
00 00
Get
BE EF
03
06 00
31 D3
02 00
01 20
00 00
Increment
BE EF
03
06 00
57 D3
04 00
01 20
00 00
Decrement
BE EF
03
06 00
86 D2
05 00
01 20
00 00
Normal
BE EF
03
06 00
46 D3
01 00
02 20
00 00
Mute
BE EF
03
06 00
D6 D2
01 00
02 20
01 00
Get
BE EF
03
06 00
75 D3
02 00
02 20
00 00
Set
OFF
ON
Get
Input Source
02 00
(Fan-error)
Set
Volume
Set
Mute
Brightness
8
Get
BE EF
03
06 00
89 D2
02 00
03 20
00 00
Increment
BE EF
03
06 00
EF D2
04 00
03 20
00 00
Decrement
BE EF
03
06 00
3E D3
05 00
03 20
00 00
ED-S3170/X3270/TECHNICAl 03.8.29 3:39 PM ページ 9
Operation type
Command data
Header
CRC
BE EF
03
06 00
FD D3
02 00
04 20
00 00
BE EF
03
06 00
9B D3
04 00
04 20
00 00
Decrement
BE EF
03
06 00
4A D2
05 00
04 20
00 00
Get
BE EF
03
06 00
01 D2
02 00
05 20
00 00
Increment
BE EF
03
06 00
67 D2
04 00
05 20
00 00
Decrement
BE EF
03
06 00
B6 D3
05 00
05 20
00 00
Get
BE EF
03
06 00
45 D2
02 00
06 20
00 00
Increment
BE EF
03
06 00
23 D2
04 00
06 20
00 00
Decrement
BE EF
03
06 00
F2 D3
05 00
06 20
00 00
Get
BE EF
03
06 00
B9 D3
02 00
07 20
00 00
Increment
BE EF
03
06 00
DF D3
04 00
07 20
00 00
Decrement
BE EF
03
06 00
0E D2
05 00
07 20
00 00
Color Balance B
Keystone_V
Get
BE EF
03
06 00
E9 D0
02 00
0B 20
00 00
Increment
BE EF
03
06 00
8F D0
04 00
0B 20
00 00
Decrement
BE EF
03
06 00
5E D1
05 00
0B 20
00 00
4:3
BE EF
03
06 00
9E D0
01 00
08 20
00 00
16:9
BE EF
03
06 00
0E D1
01 00
08 20
01 00
Small
BE EF
03
06 00
FE D1
01 00
08 20
02 00
BE EF
03
06 00
AD D0
02 00
08 20
00 00
Default
BE EF
03
06 00
62 D1
01 00
09 20
00 00
Bottom
BE EF
03
06 00
F2 D0
01 00
09 20
01 00
Top
BE EF
03
06 00
02 D0
01 00
09 20
02 00
Get
BE EF
03
06 00
51 D1
02 00
09 20
00 00
Keystone_H
Set
Get
V.Position
H.Position
H.Size
H.Phase
Sharpness
Color
Setting code
Get
Color Balance R
Picture
Position at
16 : 9 or Small
Type
Increment
Contrast
Aspect
Action
Set
Get
BE EF
03
06 00
0D 83
02 00
00 21
00 00
Increment
BE EF
03
06 00
6B 83
04 00
00 21
00 00
Decrement
BE EF
03
06 00
BA 82
05 00
00 21
00 00
Get
BE EF
03
06 00
F1 82
02 00
01 21
00 00
Increment
BE EF
03
06 00
97 82
04 00
01 21
00 00
Decrement
BE EF
03
06 00
46 83
05 00
01 21
00 00
Get
BE EF
03
06 00
B5 82
02 00
02 21
00 00
Increment
BE EF
03
06 00
D3 82
04 00
02 21
00 00
Decrement
BE EF
03
06 00
02 83
05 00
02 21
00 00
Get
Increment
Decrement
BE EF
BE EF
BE EF
03
03
03
06 00
06 00
06 00
49 83
2F 83
FE 82
02 00
04 00
05 00
03 21
03 21
03 21
00 00
00 00
00 00
Get
BE EF
03
06 00
F1 72
02 00
01 22
00 00
Increment
BE EF
03
06 00
97 72
04 00
01 22
00 00
Decrement
BE EF
03
06 00
46 73
05 00
01 22
00 00
Get
BE EF
03
06 00
B5 72
02 00
02 22
00 00
Increment
BE EF
03
06 00
D3 72
04 00
02 22
00 00
Decrement
BE EF
03
06 00
02 73
05 00
02 22
00 00
TECHNICAL
Names
9
ED-S3170/X3270/TECHNICAl 03.8.29 3:39 PM ページ 10
Command data chart (continued)
Names
Operation type
Command data
Header
Type
Setting code
Get
BE EF
03
06 00
49 73
02 00
03 22
00 00
Increment
BE EF
03
06 00
2F 73
04 00
03 22
00 00
Decrement
BE EF
03
06 00
FE 72
05 00
03 22
00 00
Auto
BE EF
03
06 00
9E 75
01 00
00 22
0A 00
NTSC
BE EF
03
06 00
FE 71
01 00
00 22
04 00
PAL
BE EF
03
06 00
6E 70
01 00
00 22
05 00
Tint
Set
CRC
Action
SECAM
BE EF
03
06 00
6E 75
01 00
00 22
09 00
NTSC 4.43
BE EF
03
06 00
5E 72
01 00
00 22
02 00
M-PAL
BE EF
03
06 00
FE 74
01 00
00 22
08 00
N-PAL
BE EF
03
06 00
0E 71
01 00
00 22
07 00
BE EF
03
06 00
0D 73
02 00
00 22
00 00
off
BE EF
03
06 00
CB D0
01 00
08 30
01 00
on
BE EF
03
06 00
5B D1
01 00
08 30
00 00
Get
BE EF
03
06 00
68 D1
02 00
08 30
00 00
Video Format
Get
Set
Sync on G
NORMAL
BE EF
03
06 00
3B 23
01 00
00 33
00 00
WHISPER
BE EF
03
06 00
AB 22
01 00
00 33
01 00
Get
BE EF
03
06 00
08 23
02 00
00 33
00 00
NORMAL
BE EF
03
06 00
C7 F0
01 00
A1 30
00 00
Set
WHISPER
Set
CINEMA
BE EF
03
06 00
57 F1
01 00
A1 30
01 00
DYNAMIC
BE EF
03
06 00
A7 F1
01 00
A1 30
02 00
Get
BE EF
03
06 00
F4 F0
02 00
A1 30
00 00
GAMMA
Set
Large
BE EF
03
06 00
C2 71
01 00
09 22
02 00
Middle
BE EF
03
06 00
32 71
01 00
09 22
01 00
Small
BE EF
03
06 00
A2 70
01 00
09 22
00 00
BE EF
03
06 00
91 70
02 00
09 22
00 00
Full
BE EF
03
06 00
43 D6
01 00
12 30
00 00
X1
BE EF
03
06 00
D3 D7
01 00
12 30
01 00
Over Scan
Get
Set
MyScreen Size
Get
BE EF
03
06 00
70 D6
02 00
12 30
03 00
off
BE EF
03
06 00
3B EF
01 00
C0 30
00 00
on
Set
MyScreen Lock
10
BE EF
03
06 00
AB EE
01 00
C0 30
01 00
Get
BE EF
03
06 00
08 EF
02 00
C0 30
00 00
Lamp Time
Get
BE EF
03
06 00
C2 FF
02 00
90 10
00 00
Filter Time
Get
BE EF
03
06 00
C2 F0
02 00
A0 10
00 00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement