Camera Quick Start Guide

Camera Quick Start Guide
Unparalleled Hardware Flexibility
BridgeVMS Quick Installation Guide
I. Package Contents:
III. Default Settings
• Camera
• Power Adapter (optional)
• Mounting Accessories
• Quick Installation Guide
• IP Address: 192.0.0.64
• Username: admin
• Password: 12345
II. Required Equipment Before Installation
IV. Accessing Your Camera – Automatic IP
Setup (With Router/DHCP server)
• PC + Monitor
• RJ-45 Network cable (1 for each device + 1 for PC)
• Network Switch
• Power Adapter with Terminal Block (Optional)
(PoE switches that are IEEE802.3af compliant
can power cameras directly without adapter.
For devices connected to non-PoE switches,
please use Power Adapter with terminal block.
Connect the white striped wire to 12V pin, and
the black wire to the GND pin. (See image)
1. Connect both the PC and the device to your
Network Switch with RJ-45 Network cables. If it is a
PoE enabled Switch, then the device is powered on.
If it is NOT a PoE enabled Switch, you will need to
use a Power Adapter with your IP device.
2. You can find your devices either via BridgeVMS
camera finder utility or via Windows Explorer.
Bridge Utility
Windows Explorer via UPnP
BridgeVMS camera utility is available on the
provided CD. Run the utility to start auto device
search. Click on the underlined IP links to access
device. There is no need to change device IPs.
Go to Start → My Computer and select “Network”
to search. Double-Click on the device to open its
web page. (See image below)
Your default browser must be Internet Explorer
to use this method
V. Accessing Your Camera- Manual IP Setup
(Without Router/DHCP server)
1. Connect the PC to the Network Switch with the
RJ-45 cable, and change your PC’s
IP to 192.0.0.64 / Subnet Mask 255.255.0.0
2. Connect the device to your Network Switch. If it is a
PoE enabled Switch, then the device is powered on.
If it is NOT a PoE enabled Switch, you will need a
Power Adapter.
3. Open Internet Explorer (Version 6.0 or above) at
http://192.0.0.64
7. Wait for 30 seconds and test the new IP with
Internet Explorer.
4. When you see the login window, input default user
and password:
• Default Username: admin
• Password: 12345
5. To go to the main menu, click the “Configuration”
button on the top right after you’ve logged in.
6. To change the IP address, navigate to Basic Configu
ration → Network. Change IPv4 address to any
unused IP address in your network scheme. Be sure
to update the Subnet Mask and Default Gateway as
well. Once finished, click “Save”.
If you assign the same IP to two cameras,
there will be in IP conflict and will not function
normally.
8. If you have more than one device, continue again
from step 2. Assign different new
IP to each camera.
SD2000/SB2000-IR-OD | Auto Focus/Remote Focus
First turn off the EPTZ feature. To do this, log into the camera and click on Configuration:
Set EPTZ to Disabled. You will see a message in the lower right that says Save Succeeded.
Once EPTZ has been disabled, we will need to focus the camera, click
on Live View and click on the PTZ control button:
From here you can use the One Touch Focus
button to get you close and then use the
Focus and Zoom controls to tighten up and
clean up the image. If you want to disable
these controls once you have found the
correct focal point, you can go back in and
enable EPTZ.
For more details, please follow our User’s Manual on www.BridgeVMS.com
Or contact Technical Support @ 713.621.9779
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement