NAVIGON 40 Essential | 40 Easy
NAVIGON 40 Essential
NAVIGON 40 Easy
NAVIGON 40 Plus
NAVIGON 40 Premium
NAVIGON 40 Premium Live
User's manual
English (United Kingdom)
June 2010
The crossed-out wheeled bin means that within the European Union
the product must be taken to separate collection at the product end-oflife. This applies to your device but also to any enhancements marked
with this symbol. Do not dispose of these products as unsorted
municipal waste.
Imprint
NAVIGON AG
Schottmüllerstraße 20A
D-20251 Hamburg
The information contained herein may be changed at any time without prior
notification. Neither this manual nor any parts thereof may be reproduced for any
purpose whatsoever without the express written consent of NAVIGON AG, nor may
they be transmitted in any form either electronically or mechanically, including
photocopying and recording. All technical specifications, drawings etc are subject to
copyright law.
 2010, NAVIGON AG
All rights reserved.
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Table of contents
1
Introduction .......................................................................................8
1.1
About this manual ...................................................................................8
1.1.1
1.1.2
1.2
Legal notice.............................................................................................8
1.2.1
1.2.2
1.3
2
Questions about the product ...................................................................9
2.1
Scope of Delivery ....................................................................................9
2.2
Description of the navigation device .....................................................10
2.3
Description of the NAVIGON Live module ............................................10
2.4
Important safety information..................................................................11
2.5
Installing the navigation system in the vehicle ........................14
Memory card ...........................................................................16
2.6
Activating the NAVIGON Live services .................................................16
2.7
Navigating with GPS .............................................................................17
Switching on the navigation device ..............................................18
3.1
Manual ..................................................................................................20
3.2
Options..................................................................................................20
Operating the navigation system ..................................................20
4.1
Information ............................................................................................20
4.2
Software keyboard ................................................................................24
4.2.1
4.2.2
5
Navigation safety information..................................................11
Safety information for the navigation device ...........................12
Safety information for the NAVIGON Live module..................12
Safety guidelines when installing the device in your car.........13
Preparing the navigation system for use...............................................14
2.5.1
2.5.2
4
Liability ......................................................................................8
Trade marks ..............................................................................9
Before you begin...............................................................................9
2.4.1
2.4.2
2.4.3
2.4.4
3
Conventions ..............................................................................8
Symbols ....................................................................................8
Special keys ............................................................................24
Entering data...........................................................................25
4.3
Options..................................................................................................26
4.4
Menus ...................................................................................................26
Navigation .......................................................................................26
5.1
Starting the navigation application ........................................................27
User's manual
Table of contents  III
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
5.2
Specifying a destination ........................................................................28
5.2.1
5.2.2
5.2.3
5.2.4
5.2.5
5.2.6
5.2.7
5.2.8
5.2.9
5.2.10
5.2.11
5.2.12
5.3
Managing destinations ..........................................................................42
5.3.1
5.3.2
5.4
Saving destinations .................................................................42
Defining the home address .....................................................42
Tracks and multi-leg routes...................................................................43
5.4.1
5.4.2
5.4.3
5.4.4
5.4.5
5.4.6
5.4.7
5.4.8
6
7
Specifying the country in which the destination is situated .....29
Entering a destination address ...............................................29
Enter Coordinates ...................................................................30
Points of interest .....................................................................32
Information about the destination............................................36
Favourites ...............................................................................36
Last Destinations ....................................................................37
Imported Addresses: Outlook / Internet ..................................37
Imported Addresses from the phone book..............................38
Navigating home .....................................................................39
Selecting destinations on the map ..........................................39
Route preview .........................................................................40
Entering the starting point .......................................................43
Entering route points ...............................................................44
Editing route points .................................................................45
Managing routes .....................................................................45
Loading routes or tracks .........................................................45
Calculating and displaying routes ...........................................46
Simulating routes ....................................................................46
Route preview .........................................................................47
Options ............................................................................................49
Working with the map.....................................................................52
7.1
Selecting the navigation map ................................................................52
7.2
Button bar..............................................................................................52
7.2.1
7.2.2
Static button bar ......................................................................52
Dynamic button bar (1-Click-Menu) ........................................53
7.3
Map in Standard mode..........................................................................54
7.4
Map in Preview mode............................................................................56
7.5
Map in Navigation mode .......................................................................57
7.5.1
7.5.2
7.5.3
7.5.4
7.5.5
7.5.6
7.6
Navigation in Vehicle mode ....................................................57
Navigation in Pedestrian mode ...............................................62
Navigation in Track mode .......................................................64
Navigation in Offroad mode ....................................................65
Map options in Navigation mode.............................................65
Quitting navigation ..................................................................66
Map in Destination search mode...........................................................66
7.6.1
IV  Table of contents
Operating in Destination search mode....................................67
User's manual
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
8
Useful functions..............................................................................68
8.1
Route profiles ........................................................................................68
8.1.1
8.1.2
8.1.3
8.1.4
8.1.5
8.2
MyPOIs: My POIs..................................................................................71
8.2.1
8.2.2
8.2.3
8.3
Route profile settings ..............................................................68
NAVIGON basic profiles .........................................................68
Creating a new route profile ....................................................69
Selecting a route profile ..........................................................69
Managing route profiles ..........................................................70
Creating your own destinations...............................................71
Symbols for your own POIs ....................................................72
POI-Import: Importing your own POIs onto the navigation
device......................................................................................73
Screenshots ..........................................................................................73
8.3.1
8.3.2
Enabling screenshots..............................................................73
Creating a screenshot .............................................................73
8.4
Tracks ...................................................................................................73
8.5
Parking near the destination .................................................................75
8.6
Nearby...................................................................................................76
8.7
POI on Your Route................................................................................77
8.7.1
8.7.2
8.7.3
Displaying POIs along the route .............................................77
Navigating to one of the destinations......................................79
Selecting categories................................................................79
8.8
NAVIGON Sightseeing..........................................................................79
8.9
Sightseeing Tours .................................................................................81
8.10 Direct Help ............................................................................................83
8.11 GPS Status, saving the current location ...............................................83
8.12 Block .....................................................................................................84
8.13 Turn-by-Turn List...................................................................................84
8.14 TMC (Traffic Information) ......................................................................86
8.14.1
8.14.2
8.14.3
8.14.4
Preview TMC...........................................................................86
Displaying traffic information ...................................................88
Showing a single message in detail........................................89
TMC Settings ..........................................................................89
8.15 Logbook ................................................................................................90
User's manual
Table of contents  V
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
9
Handsfree Module...........................................................................91
9.1
Connection with Mobile Phone..............................................................93
9.1.1
9.1.2
9.1.3
9.1.4
9.1.5
9.1.6
9.1.7
9.2
Taking a call ..........................................................................................99
9.3
Receiving a text message .....................................................................99
9.4
Making a call .......................................................................................100
9.4.1
9.4.2
9.4.3
9.4.4
9.4.5
9.5
9.6
Moving the navigation application to the foreground ............102
Entering numbers..................................................................102
Muting the microphone .........................................................102
Transferring a call to the mobile phone.................................103
Ending the call ......................................................................103
Useful functions...................................................................................103
9.6.1
9.6.2
9.7
Dialling a telephone number .................................................100
Dialling a Speed Call number ...............................................100
Calling a contact from the phone book .................................101
Calling most recently dialled, received or missed
numbers ................................................................................101
Transferring a call from your mobile telephone.....................102
During a call ........................................................................................102
9.5.1
9.5.2
9.5.3
9.5.4
9.5.5
Navigating to a contact from the phone book .......................103
Opening the mailbox .............................................................103
Configuring the hands-free function ....................................................104
9.7.1
9.7.2
10
Searching for and pairing Bluetooth devices ..........................93
Pairing from the mobile phone ................................................94
Connecting to a device ...........................................................95
Activating a mobile phone .......................................................97
Deleting a device ....................................................................97
Import Phone Book .................................................................98
Import recent calls...................................................................99
Preset....................................................................................104
Settings .................................................................................105
Navigon Live..................................................................................106
10.1 Before you begin .................................................................................106
10.1.1
Costs .....................................................................................106
10.2 Using the NAVIGON Live services......................................................107
10.2.1
10.2.2
10.2.3
10.2.4
Weather Service ...................................................................107
Parking ..................................................................................108
Google Local Search ............................................................109
Traffic Information .................................................................111
10.3 Configuring the NAVIGON Live services ............................................111
10.4 Indicating the status ............................................................................112
VI  Table of contents
User's manual
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
11
12
Configuring the navigation system .............................................112
Appendix .......................................................................................114
12.1 Technical data of the navigation device ..............................................114
12.2 Technical data of the NAVIGON Live-module ....................................115
12.3 NAVIGON Licensing Policy.................................................................116
12.4 Declaration of Conformity....................................................................120
13
14
Troubleshooting............................................................................120
Index ..............................................................................................122
User's manual
Table of contents  VII
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
1
Introduction
1.1
About this manual
1.1.1
Conventions
For better legibility and clarification, the following styles are used in this
manual:
Bold and italics:
Names of products
SMALL CAPITALS:
Names of windows and dialogue boxes
Bold:
Highlighting of important parts in the text
Underlined:
Descriptions of buttons, input boxes and other
elements on the user interface
Underlined and italics:
Names of control elements on the navigation
device
1.1.2
Symbols
The following symbols refer to specific passages of text:
Instructions and tips for operating the software
More detailed information and explanations
Warnings
1.2
Legal notice
1.2.1
Liability
The software and manual are subject to change without notice.
NAVIGON AG is not liable for the accuracy of the information contained
in this manual or for damages resulting from the use of this manual.
Suggestions for improvements and information regarding errors are
always welcome so that we can supply you with even better products in
the future.
-8-
Introduction
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
1.2.2
Trade marks
All brand and trade marks mentioned in this document and registered
by third parties are subject without reservation to copyright law and the
proprietary rights of their respective owners. All trade marks, trade
names and company names used in this document are or may be trade
marks or registered trademarks of their respective owners. All rights
reserved except those explicitly granted.
If the registered trade marks used in this manual are not explicitly
identified as such, this does not imply that the name is not subject to the
rights of a third party.
►
►
1.3
Microsoft, Outlook, Excel and Windows are registered trade marks
of the Microsoft Corporation.
NAVIGON is a registered trade mark of NAVIGON AG.
Questions about the product
You have a question concerning your product? Then visit our website
www.navigon.com and click on "Customer Services". There you will find
an area with frequently asked questions (FAQ Center) along with details
of how to contact us by phone or e-mail.
2
Before you begin
2.1
Scope of Delivery
Please check that the contents are complete. If anything is missing, get
in touch immediately with the dealer who sold you the product.
The purchased product includes the following:
►
Navigation device
►
Designer car cradle
►
Car charger cable (10-24V adapter for the vehicle's cigarette lighter)
with integrated TMC antenna
►
USB cable
►
Leaflet with illustrated installation instructions
►
Only NAVIGON 40 Premium Live:
►
►
►
Before you begin
NAVIGON Live module
SIM card holder. The card holder is glued in the leaflet and can
be removed easily. The SIM card has been broken out of its
holder already.
SIM card (already inserted in the NAVIGON Live module)
-9-
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Note: Keep the SIM card holder in a safe place! You will need the data
printed on this holder if you ever have to contact the NAVIGON Service
Centre for assistance.
2.2
Description of the navigation device
1
Touch-screen
2
On/Off
3
Microphone
4
Slot for microSD memory card
5
Mini USB socket for USB cable / mains adapter
6
Reset
7
LED
2.3
Description of the NAVIGON Live module
This chapter is relevant for you only if your navigation device is a
NAVIGON 40 Premium Live.
- 10 -
Before you begin
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
1
NAVIGON Live module
2
Mini-USB connector for connecting to the navigation device
3
Slot for the SIM card (already inserted)
4
LED
5
Mini-USB socket for the car charger cable
6
Car charger cable
2.4
Important safety information
In your own interest, please read the following safety information and
warnings carefully before starting up your navigation system.
2.4.1
Navigation safety information
Use the navigation system at your own risk.
Caution! To prevent accidents, do not operate the navigation system
while driving.
Caution! Do not look at the screen unless it is absolutely safe to do so!
Caution! Traffic regulations have priority over any instructions from the
navigation system.
Caution! Follow the instructions of the navigation system only when the
circumstances and the road traffic regulations allow you to do so! The
navigation system will still guide you to your destination even if you
deviate from the calculated route.
Before you begin
- 11 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Caution! Check that the cradle is secured and adjusted properly before
each journey.
2.4.2
Safety information for the navigation device
Caution! Protect the device from moisture. The device is neither
waterproof nor protected against splash water.
Caution! Do not open the case of the navigation device under any
circumstances.
Caution! Do not expose the navigation device to extreme heat or cold.
This may damage the device or impair its function. (Refer to "Technical
data" on page 114.)
Caution! Never unplug by pulling the cable. Doing so could severely
damage or destroy the device.
Caution! Do not subject the navigation device to severe temperature
fluctuations.
This can cause condensation to form.
Note: Do not kink the cable. Make sure that the cable cannot be
damaged by sharp-edged objects.
Note: Create a backup of the data in the internal memory of your
navigation device.
This is very easy to do with the NAVIGON Fresh software which can be
downloaded free of charge from our website www.navigon.com/fresh.
2.4.3
Safety information for the NAVIGON Live module
This chapter is relevant for you only if your navigation device is a
NAVIGON 40 Premium Live.
Caution! Protect the device from moisture. The device is neither
waterproof nor protected against splash water.
Caution! Do not open the case of the NAVIGON Live module under
any circumstances.
- 12 -
Before you begin
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Caution! Do not expose the NAVIGON Live module to extreme heat or
cold. This may damage the device or impair its function. (Refer to
"Technical data" on page 114.)
Caution! Never unplug by pulling the cable. Doing so could severely
damage or destroy the NAVIGON Live module.
Caution! Do not expose the NAVIGON Live module to severe
temperature fluctuations. This can cause condensation to form.
Note: Do not kink the cables. Make sure that the cable cannot be
damaged by sharp-edged objects.
2.4.4
Safety guidelines when installing the device in your car
Caution! Fasten the cradle so that the navigation device is easy to see
and operate by the driver. Make sure that the driver's view of the traffic
is not impeded.
Caution! Do not attach the cradle within the working zone of any
airbags.
Caution! Do not fasten the cradle too close to the steering wheel or
other controls. The driver must not be obstructed in operating any car
functions.
Caution! When installing the cradle, make sure that it will not pose a
risk in the event of an accident.
Caution! Do not run cables directly next to safety-relevant devices and
power supplies.
Caution! Check that the cradle is secured and adjusted properly before
each journey. The suction cup may become loose after a while.
Caution! After installation, check all safety-relevant equipment in the
car.
Caution! Connect the car charger cable only to cigarette lighters with
an operating voltage of 10-24V.
Caution! Disconnect the car charger cable from the cigarette lighter
whenever you park the car. The integrated mains adapter always
consumes a small amount of energy and could drain the car battery.
Before you begin
- 13 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
2.5
Preparing the navigation system for use
2.5.1
Installing the navigation system in the vehicle
Caution! Be sure to refer to all the safety information in chapter
"Important safety information" on page 11.
Securing the cradle
1. Clean the suction cup and that part of the windscreen to which you
want to secure the cradle. Both must be dry and free of dirt and
grease.
2. Open the lever on the suction cup as far as possible.
3. Place the cradle suction cup against the windscreen.
4. Press the lever towards the windscreen.
Inserting the navigation device into the cradle
On the back of the navigation device you will see a circle with two
recesses.
- 14 -
Before you begin
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
1. Hang the navigation device by the upper recess on the upper lug of
the cradle. (See illustration)
2. Then press it towards the cradle so that it latches in place.
Connecting the NAVIGON Live module to the navigation device
This section is relevant for you only if your navigation device is a
NAVIGON 40 Premium Live.
1. Connect the cable of the NAVIGON Live module to the USB socket
of the navigation device used for the power supply.
2. Connect the car charger cable to the vehicle's cigarette lighter and
to the mini-USB socket on the NAVIGON Live module.
The module's NAVIGON logo lights up orange as soon as it is
supplied with electricity. At the same time it supplies power to the
connected navigation device.
3. Make sure that the NAVIGON Live module lies on the dashboard
so that mobile radio reception is as good as possible.
Supplying power to the navigation device
This section is relevant for you only if your navigation device is one of
the following devices:
►
NAVIGON 40 Essential
►
NAVIGON 40 Easy
►
NAVIGON 40 Plus
►
NAVIGON 40 Premium
Included in delivery of the navigation device is a car charger cable with
which power can be supplied to the navigation device via the vehicle's
cigarette lighter.
►
Connect the car charger cable to the vehicle's cigarette lighter and
to the mini USB socket of the navigation device.
The LED on the bottom of the navigation device lights up orange during
charging.
As soon as the battery is fully charged, the LED lights up green.
Caution! Connect the car charger cable only to cigarette lighters with
an operating voltage of 10-24V.
Note: Insert the USB connector securely in the corresponding USB
sockets!
Caution! Be sure to refer to all the safety information in chapter
"Important safety information" on page 11.
Before you begin
- 15 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Note: It takes approx. 3 hours to charge the device when the battery is
flat.
A fully charged battery enables up to 3 hours of use depending on the
device configuration.
TMC antenna
The navigation device has an integrated TMC receiver. The TMC
antenna is integrated in the car charger cable. Once the car charger
cable is connected, the device can receive current traffic messages. If
required, it can change your route dynamically, e.g. in order to avoid a
traffic jam.
2.5.2
Memory card
A memory card is not required to operate the navigation system
because all the data required for navigation are stored in the internal
memory of the device.
When you connect the navigation system to your computer using a USB
cable, the internal memory is detected as the 'NAVIGON' drive. The slot
for the memory card is detected as the 'NAVIGON SD' drive.
Data backups, software updates and navigation map updates can be
carried out quickly and conveniently with the NAVIGON Fresh software,
which you can download free of charge from the website
www.navigon.com/fresh.
If you purchase additional navigation maps but no longer have enough
space for them in the internal memory of your navigation device, it is
also possible for you to save these maps on a memory card which you
then insert in the device. The navigation system can use navigation
maps from both memories.
2.6
Activating the NAVIGON Live services
This chapter is relevant for you only if your navigation device is a
NAVIGON 40 Premium Live.
The NAVIGON Live services must be activated before they are used
for the first time. Then they can be used free of charge for 3 months.
(Refer to "Costs" on page 106.)
The NAVIGON Live module is connected to the navigation device.
The leaflet with the activation code which came with the NAVIGON Live
module is to hand.
1. Switch on the navigation device.
The NAVIGATION window opens.
- 16 -
Before you begin
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
2. Tap on
(NAVIGON Live).
You will be asked whether you want to activate the NAVIGON Live
services.
3. Tap on Yes.
4. Enter the activation code.
5. Tap on Activate.
The NAVIGON Live services are now activated.
6. Tap on OK.
The following message appears: "You are sending 'Floating Car
Data' to NAVIGON in anonymised form. The evaluation of these
data will help in calculating times of arrival more precisely, in
recognising traffic congestion sooner, and in planning alternative
routes more reliably. No information about your person can be
derived from the data. If you do not agree, select 'No' for the setting
'Optimise Traffic Recognition'."
7. Tap on OK.
The NAVIGATION window is opened. From here you have access to all
the functions of your navigation device and all available NAVIGON Live
services.
2.7
Navigating with GPS
GPS is based on a total of at least 24 satellites orbiting the Earth and
continuously transmitting signals of their position and time. The GPS
receiver receives this data and calculates its own geographical position
on the basis of the information transmitted by the various satellites.
Data from at least three satellites is required for positioning with an
acceptable degree of accuracy. With data from four or more satellites it
is possible in addition to determine the position's altitude above sea
level. Positioning is accurate to within three metres.
Once the navigation device has determined your position, this position
can be used as a starting point for calculating a route.
The map data on your navigation device includes the geographical
coordinates of all digitally recorded points of interest, streets and
places. This enables the device to calculate a route between a starting
point and a destination.
Calculation of the current position and its representation on the map
take place approximately once every second. In other words, your
current position is always shown on the map.
Before you begin
- 17 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
3
Switching on the navigation device
►
Press the
(On/Off) key and keep it pressed until the device
switches on.
The NAVIGATION window opens.
Note: The screen lights up briefly in white, indicating that you have
started the device.
When you switch on the navigation system for the first time, you will be
asked to make the following settings:
►
your preferred language for using for the software
►
the unit of length for distances
►
the time format
►
the date format
Note: When you start the navigation application for the first time, the
DEMO MODE settings window opens.
Demo mode is intended only for demonstrating the product when no
GPS reception is possible.
When demo mode is active, navigation is not possible! Demo mode
is designed solely to simulate navigation to the centre of the
indicated destination.
►
Make sure that the Start in Demo Mode setting is at No. If
necessary tap on the
(Toggle) button in order to change
the setting from Yes to No.
►
Tap on OK.
Note: How to deactivate demo mode is explained in "Troubleshooting"
in section "I have accidentally activated demo mode" on page 121.
Note: If you have not used the navigation device for a long time, the
battery may be flat.
When you connect the navigation device to the supplied car charger
cable, it can be switched on immediately even if the battery is flat. If you
use a different charger cable or have connected your device to a PC, it
may need charging for a few minutes before it can be switched on.
Chargers and other accessories are available in the NAVIGON online
shop at www.navigon.com or in specialist stores.
- 18 -
Switching on the navigation device
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Switching the navigation device to standby mode
►
Press briefly on the
(On/Off) key (max. 2 seconds).
A message will appear telling you that the device will be switched to
standby mode in several seconds.
►
Wait for the device to be switched to standby mode or tap on
Standby.
Automatic Standby
You can configure the navigation device so that it is automatically
switched to standby mode when not in use.
►
►
►
In the NAVIGATION window tap on Options > Settings > General >
Automatic Standby.
Select after how much time you want the navigation device to be
switched to standby mode (Never, After 10 mins., After 20 mins.,
After 30 mins.).
Select Power Loss in order to switch the device to standby mode
when the external power supply is interrupted. As soon as the
device is connected again to the external power supply it will switch
on again automatically.
Switching off the navigation device
►
Press the
(On/Off) key and keep it pressed until the device
switches off (approx. 6 seconds)
-or-
1. Press briefly on the
(On/Off) key (max. 2 second).
A message will appear telling you that the device will be switched to
standby mode in several seconds.
2. Tap on Off.
Note: When you switch the navigation device to standby mode, the next
time it is switched on it will start very quickly and with the window which
was active when switched off. In standby mode the device still
consumes a small amount of energy however. Depending on how full
the battery is, it can become flat within a few days or a few weeks.
When you switch off the device, it consumes no energy. It can then take
several months for the battery to become flat. Switching the device on
again triggers a restart which can take some time (approx. 30 seconds).
Your settings and your saved destinations and routes will be retained.
Switching on the navigation device
- 19 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
3.1
Manual
An excerpt of this manual describing the most important functions of the
navigation software is saved on the navigation device.
To open the manual:
1. In the NAVIGATION window, tap on Options > Manual.
The TABLE OF CONTENTS window opens.
2. Tap on the name of the chapter you want to read.
The content of the chapter is shown.
(Up) and
(Down) buttons you can scroll up one
With the
page and down one page respectively.
(To the Left) and
(To the Right) buttons you
With the
can open the previous or the next chapter respectively.
►
►
Tap on the Table of Contents button in order to open the Table of
Contents window.
Tap on the
(Close) button in order to close the manual.
The NAVIGATION window is opened.
3.2
Options
Some windows offer options that lead to more functions.
A description of all available options can be found in the chapter
"Options" on page 49.
4
Operating the navigation system
4.1
Information
Various information symbols are located at the top of many windows.
GPS
The GPS symbol can indicate the following GPS reception states:
No GPS (No symbol): The built-in GPS receiver is not operational.
Contact us if the problem persists. (Refer to "Questions about the
product" on page 9.)
No Signal: Data is being received from less than three satellites.
Position cannot be calculated.
- 20 -
Operating the navigation system
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
GPS Ready: Data is being received from at least 3 satellites. Position
can be calculated.
For details of the GPS status refer to chapter "GPS Status, saving the
current location" on page 83.
Compass
The Compass symbol indicates in which direction you are currently
heading. It can indicate the following points of the compass: N, NE, E,
SE, S, SW, W, NW.
Track
The
(Record Track) symbol indicates that a track is being recorded
at this moment.
For more information about tracks refer to chapter "Tracks" on page 73.
Energy
The Energy symbol can indicate the following states of the integrated
battery:
The device is being supplied by an external power source. The battery
is fully charged.
The battery cannot be charged because its temperature is too high or
too low.
The device is being supplied by an external power source. The battery
is being charged.
The device is being supplied by its internal battery. The battery charge
is sufficient.
The device is being supplied by its internal battery. The battery charge
is low.
NAVIGON Live Services
This section is relevant for you only if your navigation device is a
NAVIGON 40 Premium Live.
The NAVIGON Live Services symbol indicates the availability of the
NAVIGON Live services. The following states can be symbolised:
Operating the navigation system
- 21 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
(No symbol) No NAVIGON Live Services: The NAVIGON Live module
is not connected or is wrongly connected, or the NAVIGON Live
services are deactivated. (Refer to "Configuring the NAVIGON Live
services" on page 111.)
(Red) Connecting: The NAVIGON Live services are activated. There
is no connection yet to the NAVIGON Live server.
(Light grey) NAVIGON Live Services Ready: There is a connection to
the NAVIGON Live server. The NAVIGON Live services are available.
Traffic Information
TMC
The navigation system has an integrated TMC receiver which supplies
up-to-date traffic information. Using this information the navigation
system can change your route dynamically, for example in order to
avoid a traffic jam.
Note: This function is only available if TMC traffic messages are being
transmitted in the country in which you are travelling. This is not the
case in all countries.
The TMC symbol can display the following TMC reception status:
Tuning (in red): The TMC receiver is operational but cannot find a
transmitter that is sending TCM signals. There are no active traffic
messages.
Tuning: The TMC receiver is operational but cannot find a station that
is transmitting TMC signals. Traffic messages are active however. This
can be the case, for example, when travelling through a tunnel.
TMC on Standby (in grey): Traffic messages can be received.
Note: The TMC antenna is integrated in the car charger cable. The
Tuning symbol may still appear therefore when the car charger cable is
not connected to the navigation device.
For details of the TMC function refer to chapter "TMC (Traffic
Information)" on page 86.
Traffic Live
This section is relevant for you only if your navigation device is a
NAVIGON 40 Premium Live.
You can draw traffic information either from the NAVIGON Live
services (Traffic Live) or from radio stations (TMC). (Refer to
"Configuring the NAVIGON Live services" on page 111.)
- 22 -
Operating the navigation system
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
The Traffic Live symbol appears when you are drawing traffic
information from the NAVIGON Live service.
Note: This function is useful above all when TMC traffic messages are
being transmitted in the country in which you are travelling and there
are many vehicles using the service. This may not be the case
everywhere.
The Traffic Live symbol can indicate the following traffic information
reception states:
(Red) Connecting: The last attempt to call up traffic information from
the NAVIGON Live server failed. This can be the case, for example,
when travelling through a tunnel. Information which was called up
previously may still be active however.
(Light grey) Traffic Live Ready: Traffic information was called up
successfully. The active information is up to date.
Bluetooth / Phone
This section is relevant for you only if your navigation device is one of
the following devices:
►
NAVIGON 40 Premium
►
NAVIGON 40 Premium Live
The navigation device has an integrated Bluetooth hands-free module.
This enables you to use the device as a hands-free kit for up to two
mobile phones with Bluetooth capability.
The Phone symbol can display the following states of the hands-free
module:
No Bluetooth (No symbol): The Bluetooth function is deactivated.
Not connected (red mobile phone): The navigation device has no
Bluetooth connection to another device.
Connected (white mobile phone): The navigation device is connected
to a mobile phone and can be used as a hands-free car kit. The number
indicates which of the two phones is currently active.
Call in Progress (green mobile phone): The hands-free module of the
navigation device is being used for a phone call. The number indicates
which of the two phones is being used to make the call.
Headset: A headset is connected. All the instructions given by the
navigation system are heard over the headset. The telephone functions
of the hands-free module are not available.
Operating the navigation system
- 23 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Muting
The Muting symbol can indicate the following states:
No symbol: The navigation application is not muted.
Muting: The navigation application is muted. If the device is navigating
at the moment, you will not hear any driving instructions.
Note: This icon indicates only the muted state of the navigation
instructions. It says nothing about the volume of the hands-free module.
4.2
Software keyboard
A software keyboard appears on the screen when text entries are
necessary.
All entries can be made on the software keyboard using your fingertips.
Only capital letters can be entered.
When entering town or street names you need not enter any special
characters or umlauts. The navigation system fills in these characters
for you automatically. For example, if you are looking for the town of
"Bärnau", then simply type in the word "BARNAU". Special characters
may be helpful however when naming saved destinations and routes.
4.2.1
Special keys
inserts a space.
deletes the character in front of the cursor.
opens the keyboard with numerals.
Latin, Cyrillic and Greek alphabet
opens the keyboard with the Latin alphabet.
Note: The layout for the keyboard with the Latin alphabet can be
configured.
►
►
In the NAVIGATION window tap on Options > Settings > General >
Keypad layout (Latin Alphabet).
Select the layout you want to use (QWERTZ, QWERTY, ABCDEF,
AZERTY).
opens the keyboard with the Cyrillic alphabet.
opens the keyboard with the Greek alphabet.
- 24 -
Operating the navigation system
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
When you want to enter addresses, names or POIs, the keyboard with
the alphabet for the country in question will open automatically.
When you want to save a destination to Favourites or when you enter a
POI category or a country, the keyboard with the alphabet of the user
interface will open automatically.
You can also switch from the Cyrillic or Greek keyboard to the Latin
keyboard. Many addresses can then also be entered as transliterations
or in the language of the user interface.
Example: The language of the user interface is English. You want to
navigate to Moscow. You have the following options:
►
"Москва" (Cyrillic)
►
"Moskva" (transliterated)
►
"Moscow" (English).
Note: Street names and place names can be entered only in the
language of the user interface if that is how they exist in the map's
database.
Note: The maximum number of keyboards is always 2.
Umlauts, accents and other letters
Another keyboard with special characters is available for each alphabet.
opens the keyboard with Latin special characters.
opens the keyboard with Cyrillic special characters.
opens the keyboard with Greek special characters.
As soon as you have entered a special character the letter keyboard
reappears.
4.2.2
Entering data
Often you can select an entry from a list. This is the case, for example,
when you enter a location.
As soon as you enter the first letter, the largest city in the given country
that begins with this letter appears.
Enter more letters and after each entry the first city which begins with
these letters will appear.
►
When the correct location appears, tap on
complete the entry.
Operating the navigation system
(OK) in order to
- 25 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
You can open at any time a list containing all the locations which begin
with the letters or include the text already entered. The more letters you
enter, the shorter the list becomes.
►
Tap on
(Open List) in order to call up this list.
You can use the
(Up) button and the
move through the list.
►
(Down) button to
Tap on an entry in the list to select it and transfer it to the input box.
The list closes once an entry has been selected. You are now
finished with entering the city.
►
Tap on
an entry.
(Close List) in order to close the list without selecting
Note: The list opens automatically as soon as it contains only 4 or less
entries.
4.3
Options
Some windows offer options that lead to more functions.
A description of all available options can be found in the chapter
"Options" on page 49.
4.4
Menus
Some buttons have menus which open when activated.
►
Tap on a menu point to execute its function.
If you would like to quit the options list without selecting a function, tap
on the button you used to open the menu.
5
Navigation
Use the navigation system at your own risk.
Caution! Be sure to refer to all the safety information in chapter
"Important safety information" on page 11.
Impaired GPS reception
If GPS reception is impaired, navigation will be interrupted. As soon as
GPS reception is restored, the navigation system calculates any change
of position which has occurred in the meantime. Navigation is then
continued automatically.
- 26 -
Navigation
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Arriving at your destination
When you have reached your selected destination, a message to this
effect will be displayed.
Only your current position (orange arrow) and the destination flag will
now be shown on the map.
5.1
Starting the navigation application
You have switched on the navigation device.
The following message appears:
"Please note that the road traffic regulations are prior to the instructions
of the navigation system. Please do not operate the device while
driving."
►
After you have read and fully understood the message, tap on OK.
If you do not accept the content of the message, tap on Cancel in
order to exit the navigation application.
The NAVIGATION window is opened. From here you can access all the
functions of the navigation application.
Initialising the GPS receiver
Note: Good reception of GPS data requires an unobstructed path from
the GPS receiver to the satellites. Tunnels, narrow thoroughfares
between buildings and reflecting house fronts can restrict GPS
reception greatly or make it impossible. If the GPS receiver or the
navigation device is inside a vehicle, a metallised windscreen or a
windscreen heater can be the cause of poor GPS reception.
As soon as the navigation device has been switched on, initialisation of
the GPS receiver will begin.
The integrated GPS receiver is not initialised for the first time until the
navigation application is started for the first time. It can take up to
5 minutes to initialise the GPS receiver for the first time.
Note: If the GPS symbol indicates GPS Ready after far less than
5 minutes, it is advisable to leave the navigation device switched on for
at least another 15 minutes in order to ensure reliable operation of the
receiver.
Each time you switch on the navigation device after this, GPS reception
will start within a short time.
If the navigation device has not been switched on for more than a week,
it can take up to 10 minutes to re-initialise the receiver.
In the top right hand corner of the screen you will see the GPS symbol.
As soon as data from at least three satellites is received, the symbol will
change to
Navigation
(GPS Ready).
- 27 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Note: Initialisation takes the least time if you do not start driving until
the initialisation has finished.
For more details about the GPS symbol refer to chapter "GPS" on
page 20.
Returning to the Navigation window
The NAVIGATION window opens when the navigation application is
started.
If another window of the navigation application is open, tap on
(Back). This will return you to the window you came from.
►
5.2
Tap on
opened.
(Back) repeatedly until the NAVIGATION window is
Specifying a destination
Under New Destination you can enter destinations to which you have
not yet navigated or which you have not saved.
Here you can enter the destination's address or coordinates, select a
POI, or select a destination with the Direct Access function.
Note: The first time that you want to enter a new destination you will be
asked to select the country in which your destination is situated.
Under My Destinations you can select from the following lists of
destinations and addresses:
►
FAVOURITES: All destinations that you have entered and then saved.
Three special destinations are also saved in the FAVOURITES list:
►
►
►
►
►
- 28 -
My Address: The address which was saved as the home
address (refer to "Defining the home address" on page 42).
My Vehicle: The location of your vehicle is automatically saved
when you use the Parking Close to Destination function (refer
to "Parking near the destination" on page 75).
My Starting Point: The starting point of the last navigation is
automatically saved.
LAST DESTINATIONS: Destinations to which you have navigated on a
previous occasion.
IMPORTED ADDRESSES: All destinations that you have imported from
Microsoft Outlook or from other data sources.
Navigation
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
5.2.1
Specifying the country in which the destination is situated
At top left in the ADDRESS, POI IN A CITY and POI NATIONWIDE windows
you will find the Country button. It bears the flag of the country in which
you can currently select destinations for the navigation application.
If your destination is in a different country, then proceed as follows:
1. Tap on the Country button.
2. Enter the name of the country in which your destination is situated.
The button shows the flag of the destination country.
Note: The selection list contains only those countries whose maps are
available to the navigation device.
5.2.2
Entering a destination address
1. In the NAVIGATION window, tap on New Destination > Enter an
Address.
Note: The following description is based on City First as the order for
entering the address.
If the navigation device contains the map of a country in which the
street is usually listed first (e.g. Sweden, Norway, ...), you can also
choose Street First as the order for entering the destination address.
You can define the order in the NAVIGATION window at Options >
Settings > General > Input Mode for Address Data.
Please note however that the Street First order of entry is not possible
for all countries. In this case you must enter the city first.
The ADDRESS window opens.
1. Enter the name or the postal code of the destination town.
2. Enter the name of the destination street.
3. Enter the house number. If you do not know the house number,
then leave this box empty.
If you don't know the house number but know the name of a nearby
side street, then tap on the Cross Street box and enter the name of
this street. The navigation system will calculate a route to the
intersection of the streets you have entered.
The DETAILED INFORMATION ABOUT THE DESTINATION window opens.
Indicated on the Activate MyRoutes button is whether several route
suggestions are to be calculated (Yes) or not (No).
►
Navigation
Tap on Activate MyRoutes in order to change the setting.
- 29 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Note: The Activate MyRoutes button is available only when you have
entered all the address information. You can also make this setting
under Options > Settings > Navigation > Activate MyRoutes.
4. Tap on Start Navigation in order to navigate to the stipulated
address.
-orTap on Parking in order to search for and navigate to a car park
near your destination.
Sometimes the destination cannot be found exactly because, for
example, the entered combination of place and street name exists
several times.
In this case a window will open with a list of all the addresses
matching your entry plus additional information.
►
Tap on the address to which you want to navigate.
If the entered house number is not included on the map, the window
will show an address with the house number closest to the one
entered.
The map opens in Preview mode. The destination is indicated on
the map.
For detailed information on how to start navigation, please refer to
chapter "Route preview" on page 40. Please read on there.
Note: It is not necessary to enter all the address details. You can tap on
(Start Navigation) before you get that far.
If you specify the town only, the navigation system will calculate a route
to the town centre.
If you specify only the town and street without specifying a house
number or cross street, the navigation system will calculate the best
route to this street.
5.2.3
Enter Coordinates
You can also enter the geographic coordinates of your destination. The
coordinates can be entered as decimal degrees or in degrees, minutes
and seconds.
1. In the NAVIGATION window, tap on New Destination > Enter
Coordinates.
The ENTER COORDINATES window opens.
Entering as a decimal number
2. Enter the degree of latitude.
- 30 -
Navigation
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Begin the entry with a minus sign if you want to enter a southern
degree of latitude.
3. Enter the degree of longitude.
Begin the entry with a minus sign if you want to enter a western
degree of longitude.
Entering with minutes / seconds
2. Enter the degree of latitude.
Use the corresponding buttons shown on the keyboard in order to
enter the units:
(degrees),
(minutes),
(seconds).
The (N S) button alongside the entry box indicates whether it is a
northern or southern degree of latitude.
►
Tap on the button if you want to change the current setting.
3. Enter the degree of longitude.
Use the corresponding buttons shown on the keyboard in order to
enter the units:
(degrees),
(minutes),
(seconds).
The (E W) button alongside the entry box indicates whether it is an
eastern or western degree of longitude.
►
Tap on the button if you want to change the current setting.
The DETAILED INFORMATION ABOUT THE DESTINATION window opens.
Indicated on the Activate MyRoutes button is whether several route
suggestions are to be calculated (Yes) or not (No).
►
Tap on Activate MyRoutes in order to change the setting.
4. Tap on Start Navigation in order to navigate to the stipulated
address.
-orTap on Parking in order to search for and navigate to a car park
near your destination.
Note: If the destination with the coordinates you entered does not lie on
the road system covered by the map, navigation will be performed as
far as the nearest road point using the mode defined by the selected
route profile. From this point on, the navigation system will automatically
switch to Offroad mode. (Refer to "Navigation in Offroad mode" on
page 65.)
Navigation
- 31 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
5.2.4
Points of interest
Points of Interest, called POI for short, are useful addresses that are
catalogued according to particular criteria.
POIs include ports, airports, restaurants, hotels, petrol stations, public
buildings, doctor's surgeries, hospitals, shopping centres, etc.
Points of interest can be displayed on the map by means of a symbol.
In the NAVIGATION window tap on Options > Settings > Map Display >
Categories Shown in order to select the categories you want to appear
on the map.
Note: If you have created your own POIs, they will be available under
the MyPOIs category. For more details about creating your own POIs
refer to chapter "MyPOIs: My POIs" on page 71.
POI nearby
POIs nearby are POIs located within a certain radius of your current
location. This means you can always find the nearest petrol station for
example, no matter where you are.
Note: GPS reception must be good enough for determining your
position. Check the
(GPS Ready) symbol to see whether GPS
reception is good enough.
For more details refer to the chapter "Initialising the GPS receiver" on
page 27.
Note: The Direct Access section offers 3 categories of POI from the
current vicinity which can be searched for quickly and without additional
entry.
For more details refer to the chapter "Direct access to POI" on page 35.
1. In the NAVIGATION window tap on New Destination > Search for
POI > Nearby.
The POI NEARBY window opens.
2. Select a category from which you would like to find a POI.
Categories in which no destinations are available nearby cannot be
selected.
If sub-categories exist for the category you have selected, the Sub
Category list opens.
3. Select the sub-category from which you would like to select a POI.
The Destination list opens. It contains the nearest POIs in the
specified category, sorted by distance.
4. If the list is very long:
►
- 32 -
Tap on
(Close List).
Navigation
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
The keyboard appears.
►
Enter a number of letters from the destination.
►
Tap on
(Open List).
The list now contains only those destinations which begin with the
letters entered.
5. Tap on the name of the destination.
The DETAILED INFORMATION ABOUT THE DESTINATION window opens.
Indicated on the Activate MyRoutes button is whether several route
suggestions are to be calculated (Yes) or not (No).
►
Tap on Activate MyRoutes in order to change the setting.
6. Tap on Start Navigation.
-orTap on Parking in order to search for and navigate to a car park
near your destination.
The map opens in Preview mode. The destination is indicated on
the map.
For detailed information on how to start navigation, please refer to
chapter "Route preview" on page 40. Please read on there.
POI of nationwide significance
POIs of nationwide significance are airports, sights, national
monuments, large ports etc. This way you can find well-known places of
interest even if you don't know the name of their location.
1. In the NAVIGATION window tap on New Destination > Search for
POI > Nationwide.
The POI NATIONWIDE window opens.
2. Select a category from which you would like to find a POI.
The Destination list opens. It contains the POI from the selected
category, sorted alphabetically.
3. If the list is very long:
►
Tap on
(Close List).
The keyboard appears.
►
Enter a number of letters from the destination.
►
Tap on
(Open List).
The list now contains only those destinations which begin with or
contain the letters entered.
Navigation
- 33 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
4. Tap on the name of the destination.
The DETAILED INFORMATION ABOUT THE DESTINATION window opens.
Indicated on the Activate MyRoutes button is whether several route
suggestions are to be calculated (Yes) or not (No).
►
Tap on Activate MyRoutes in order to change the setting.
5. Tap on Start Navigation.
-orTap on Parking in order to search for and navigate to a car park
near your destination.
The map opens in Preview mode. The destination is indicated on
the map.
For detailed information on how to start navigation, please refer to
chapter "Route preview" on page 40. Please read on there.
POI in a particular location
POIs in a particular location can be useful when navigating in an
unfamiliar town.
1. In the NAVIGATION window tap on New Destination > Search for
POI > in a City.
The POI IN A CITY window opens.
2. Enter the name or the postal code of the destination town.
3. Select a category from which you would like to find a POI.
Categories in which no destinations are available in the selected
town cannot be entered.
If sub-categories exist for the category you have selected, the Sub
Category list opens.
4. Select the sub-category from which you would like to select a POI.
The Destination list opens. It contains POI from the specified
category, sorted alphabetically.
5. If the list is very long:
►
Tap on
(Close List).
The keyboard appears.
►
Enter a number of letters from the destination.
►
Tap on
(Open List).
The list now contains only those destinations which begin with or
contain the letters entered.
6. Tap on the name of the destination.
- 34 -
Navigation
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
The DETAILED INFORMATION ABOUT THE DESTINATION window opens.
Indicated on the Activate MyRoutes button is whether several route
suggestions are to be calculated (Yes) or not (No).
►
Tap on Activate MyRoutes in order to change the setting.
Sometimes the destination cannot be found exactly because, for
example, several restaurants with the same name exist in the town
in question.
In this case a window opens with all the destinations matching your
entry plus additional information.
►
Tap on the destination to which you want to navigate.
7. Tap on Start Navigation.
-orTap on Parking in order to search for and navigate to a car park
near your destination.
The map opens in Preview mode. The destination is indicated on
the map.
For detailed information on how to start navigation, please refer to
chapter "Route preview" on page 40. Please read on there.
Direct access to POI
The direct access area contains 3 categories of POI. Destinations in
your vicinity that correspond to one of these categories can be viewed
here quickly and without further entry.
►
In the NAVIGATION window tap on Options > Settings > General in
order to select which categories or sub-categories are to be
available for direct access.
Note: GPS reception must be good enough for determining your
position. Check the
(GPS Ready) symbol to see whether GPS
reception is good enough.
For more details refer to the chapter "Initialising the GPS receiver" on
page 27.
1. In the NAVIGATION window tap on New Destination.
The NEW DESTINATION menu opens.
In the Direct Access area you are shown the symbols of those POI
categories that are available by direct access.
2. Tap on the category from which you would like to select a POI.
A list opens. It contains the nearest POIs in the specified category,
sorted by distance.
3. Tap on the name of the destination in order to start navigation to it.
Navigation
- 35 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
The map opens in Preview mode. The destination is indicated on
the map.
For detailed information on how to start navigation, please refer to
chapter "Route preview" on page 40. Please read on there.
5.2.5
Information about the destination
For many destinations that you specify, there will be further information
available, stored in the navigation system's database.
There is, for example, a telephone number available for many
restaurants. You can then call the restaurant to reserve a table, for
example.
One of the destination entry windows described above is open.
►
Tap on Options > Info.
The DESTINATION INFO window opens. It contains all the information
about the specified destination that is stored in the navigation system's
database.
►
►
►
5.2.6
Tap on Close in order to close the DESTINATION INFO window again.
Tap on
map.
(Show on Map) in order to see the destination on the
Tap on
(Save Destination) in order to save the destination in
the FAVOURITES list.
Favourites
Destinations to which you want to travel often can be saved in the
FAVOURITES list.
In the FAVOURITES list you can save up to 500 destinations.
Information on how to save a destination can be found in chapter
"Saving destinations" on page 42.
1. In the NAVIGATION window, tap on My Destinations > Favourites.
2. Tap on the destination to which you want to navigate.
The DETAILED INFORMATION ABOUT THE DESTINATION window opens.
Indicated on the Activate MyRoutes button is whether several route
suggestions are to be calculated (Yes) or not (No).
►
Tap on Activate MyRoutes in order to change the setting.
3. Tap on Start Navigation.
-or-
- 36 -
Navigation
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Tap on Parking in order to search for and navigate to a car park
near your destination.
The map opens in Preview mode. The destination is indicated on
the map.
For detailed information on how to start navigation, please refer to
chapter "Route preview" on page 40. Please read on there.
Note: Favourites are indicated on the map by a small flag with their
name.
5.2.7
Last Destinations
The last 12 destinations to which you have navigated are saved by the
navigation system in the LAST DESTINATIONS list.
1. In the NAVIGATION window, tap on My Destinations > Last
Destinations.
2. Tap on the destination to which you want to navigate.
The DETAILED INFORMATION ABOUT THE DESTINATION window opens.
Indicated on the Activate MyRoutes button is whether several route
suggestions are to be calculated (Yes) or not (No).
►
Tap on Activate MyRoutes in order to change the setting.
3. Tap on Start Navigation.
-orTap on Parking in order to search for and navigate to a car park
near your destination.
The map opens in Preview mode. The destination is indicated on
the map.
For detailed information on how to start navigation, please refer to
chapter "Route preview" on page 40. Please read on there.
5.2.8
Imported Addresses: Outlook / Internet
You can use the NAVIGON Sync software to export to your navigation
system the contact addresses which you have saved in Microsoft
Outlook on your computer.
From many route planners on the Internet it is also possible to copy the
entered destination address directly onto your navigation system. This
function is clearly indicated on those websites which offer it.
Note: You can download NAVIGON Sync free of charge from our
website www.navigon.com.
Navigation
- 37 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Contacts which have been saved with several addresses will appear
once with each address in the IMPORTED ADDRESSES list.
1. In the NAVIGATION window tap on My Destinations > Imported
Addresses > Outlook / Internet.
2. Tap on the address to which you want to navigate.
The DETAILED INFORMATION ABOUT THE DESTINATION window opens.
Indicated on the Activate MyRoutes button is whether several route
suggestions are to be calculated (Yes) or not (No).
►
Tap on Activate MyRoutes in order to change the setting.
3. Tap on Start Navigation.
-orTap on Parking in order to search for and navigate to a car park
near your destination.
The map opens in Preview mode. The destination is indicated on
the map.
For detailed information on how to start navigation, please refer to
chapter "Route preview" on page 40. Please read on there.
5.2.9
Imported Addresses from the phone book
This section is relevant for you only if your navigation device is one of
the following devices:
►
NAVIGON 40 Premium
►
NAVIGON 40 Premium Live
The phone book of a mobile phone with which you are connected can
be imported into the navigation device. Addresses from the phone book
are then found in the IMPORTED ADDRESSES FROM THE PHONE BOOK list.
1. In the NAVIGATION window tap on My Destinations > Imported
Addresses > From the phone book.
2. Select the contact you want from the phone book.
3. Tap on the address to which you want to navigate.
The DETAILED INFORMATION ABOUT THE DESTINATION window opens.
Indicated on the Activate MyRoutes button is whether several route
suggestions are to be calculated (Yes) or not (No).
►
Tap on Activate MyRoutes in order to change the setting.
4. Tap on Start Navigation.
-orTap on Parking in order to search for a car park near your
destination.
- 38 -
Navigation
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
The map opens in Preview mode. The destination is indicated on
the map.
For detailed information on how to start navigation, please refer to
chapter "Route preview" on page 40. Please read on there.
5.2.10
Navigating home
You can save an address as your home address. You can navigate to
your home address at any time by pressing a single button.
More information about entering your home address can be found in the
chapter "Defining the home address" on page 42.
►
In the NAVIGATION window tap on Take Me Home.
If you have not yet entered your home address, a dialog box will
notify you of this.
Navigation starts. The route profile used for the previous navigation will
be applied.
5.2.11
Selecting destinations on the map
You may select a destination directly on the map. This is a quick way to
select towns, streets and POI.
1. In the NAVIGATION window tap on Show Map.
2. Tap on
(Destination search).
The map opens in Destination search mode.
3. Tap on the point to which you want to navigate.
Note: For details of how to change the map view so that your destination
is easily seen refer to the chapter "Map in Destination search mode" on
page 66.
The destination that you have selected appears under the cross
hairs.
The geographical coordinates of the destination and the
corresponding address are shown in the bottom third of the screen.
4. Tap on
(OK).
The DESTINATION ON MAP window opens. The detailed address data
of the selected destination is displayed in the upper left-hand
corner.
5. Tap on Take Me There.
The map opens in Preview mode. The destination is indicated on
the map.
Navigation
- 39 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
For detailed information on how to start navigation, please refer to
chapter "Route preview" on page 40. Please read on there.
5.2.12
Route preview
The map is open in Preview mode.
The navigation destination is depicted by a small flag.
For detailed information refer to the chapter "Map in Preview mode" on
page 56.
Route Profile
The route is calculated on the basis of a route profile. The current route
profile is indicated at the top right edge of the map.
Route profiles take account of the characteristics and special aspects of
the different modes of transport. For example a route profile for bicycles
will exclude motorways from the route calculation but will include roads
which other vehicles are not allowed to use. And a bicycle profile will
calculate different arrival times than a motorcycle profile.
Note: If you select a pedestrian profile, a type of navigation specially
developed for pedestrians will be started. (Refer to "Navigation in
Pedestrian mode" on page 62.)
►
Tap on the Route Profile button if you want to select a different
route profile.
For details of how to create and select route profiles refer to chapter
"Route profiles" on page 68.
Turn-by-Turn List
►
If you want to see detailed directions for the route, tap on Options >
Turn-by-Turn List.
For details of the functions in the TURN-BY-TURN LIST window refer to
chapter "Turn-by-Turn List" on page 84.
- 40 -
Navigation
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
MyRoutes
This section is relevant for you only if your navigation device is one of
the following devices:
►
NAVIGON 40 Easy
►
NAVIGON 40 Plus
►
NAVIGON 40 Premium
►
NAVIGON 40 Premium Live
When the MyRoutes function is activated, the navigation system
calculates up to three routes on the basis of the currently selected route
profile and shows them on the map in different colours (orange, green,
blue) and with a number. For each route there is a button with the same
number and a symbol in the same colour.
When calculating the time of arrival or the trip time, the navigation
system takes account of additional factors such as day of the week,
time of day or traffic messages.
The route which corresponds best to the selected route profile is
marked with "MyRoute".
Note: Even when the MyRoutes function is activated, sometimes only
one additional route or no additional routes at all can be calculated for a
particular route. No further suggestion is then shown on the button in
question.
Start Navigation
►
Tap on the button of the route which you want to use for the
navigation.
If you select a route for which traffic obstructions have been announced,
the PREVIEW TMC window may open before navigation starts. (Refer to
"Preview TMC" on page 86.)
►
Select whether you want to use the original route (Current Route) or
a detour (Alternative route).
No GPS reception
If GPS signal reception is not good enough, the following message will
appear: "Waiting for GPS-Signal…"
You have the following options:
►
►
Navigation
Wait. As soon as GPS reception is good enough for determining
your position, the route will be recalculated and navigation will
begin.
Tap on Cancel. The window in which you entered your destination
will open again. Your destination is saved in the LAST DESTINATIONS
list.
- 41 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
►
Tap on Demo. The route will be calculated using the centre of the
destination location as starting point. Navigation will then be
simulated on this route.
Tap on
(Back) in order to terminate the demonstration.
Note: If you selected the destination on the map, then the Demo button
is not available.
5.3
Managing destinations
Every destination you enter and destinations from the LAST
DESTINATIONS and IMPORTED ADDRESSES lists can be saved in the
FAVOURITES list. This makes sense if you frequently navigate to this
particular destination.
Note: Favourites are indicated on the map by a small flag with their
name.
5.3.1
Saving destinations
1. Enter a destination. (Refer to "Entering a destination address " on
page 29 or "Points of interest" on page 32). Do not tap on the Start
Navigation button!
2. Tap on Options > Save Destination.
-or1. Select a destination from the LAST DESTINATIONS list or from the
IMPORTED ADDRESSES list. (Refer to "Last Destinations" on page 37
or "Imported Addresses: Outlook / Internet" on page 37). Do not tap
on the Start Navigation button!
2. Tap on Options > Save as Favourite.
3. Enter a name for the destination.
4. Tap on Save.
5.3.2
Defining the home address
You can always start navigation to your home address very quickly by
tapping in the NAVIGATION window on Take Me Home.
You can define exactly one destination as your home address. This
destination is saved in the FAVOURITES list.
Proceed as follows:
1. In the NAVIGATION window, tap on New Destination > Enter an
Address.
The ADDRESS window opens.
- 42 -
Navigation
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
2. Enter your home address.
3. Tap on Options > Save Destination.
4. Enter a name for the address (e.g. "Home Address").
Your home address is now saved in the FAVOURITES list.
5. Tap on
(Back).
The NAVIGATION window opens.
6. Tap on My Destinations > Favourites.
7. Select from the FAVOURITES list the destination which you want to
define as your new home address. (Refer also to Favourites on
page 36.)
8. Tap on Options > Home Address.
The selected destination has now been saved as your home address.
Your home address now appears in the FAVOURITES list marked by a
house symbol.
Note: The home address is also indicated on the map by a house
symbol.
Changing the home address
You can define a different address as the home address at any time.
Proceed as described above.
5.4
Tracks and multi-leg routes
It is possible to plan routes without GPS reception, for example in the
comfort of your home. Planned routes can be saved for later use. This
allows you to plan as many routes as you like, for example for your
holidays.
1. In the NAVIGATION window tap on Options.
The options list opens.
2. Tap on the Routes and Tracks option.
The ROUTES AND TRACKS window opens.
5.4.1
Entering the starting point
The starting point of a route is the point at which you want to begin your
trip. This is not necessarily the current location. If you are planning a
route for your holidays at home, you could, for example, enter your
hotel as the starting point.
The starting point is only important if you want to see a planned route
on the map but currently have no GPS reception, or if you are not
currently at the planned starting point. This is why your selected starting
point has the flow number "0".
Navigation
- 43 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
As soon as you start navigation, your current location will be used as
the starting point for the route calculation.
The first leg of the route is therefore the journey to the route point with
flow number "1".
1. Tap on the Specify Starting Point box.
The STARTING POINT menu opens.
If you want to enter your current location as the starting point:
2. Tap on the Current Position menu item.
If you want to enter a different starting point:
2. Tap on the corresponding button.
3. Enter the starting point. (Refer to the corresponding section of the
chapter "Specifying a destination" on page 28.)
4. Tap on
(Set Starting Point).
The selected starting point will now be shown next to the 0 (Starting
Point) button.
Changing the starting point
►
Tap on the starting point (button 0).
The STARTING POINT menu opens. You can now enter a different
starting point. Proceed as described above.
5.4.2
Entering route points
The route points of a route are the destinations that you want to
navigate to.
The flow number for each route point is indicated on a button in front of
it.
1. Tap on the Add Route Point box.
The ROUTE POINT menu opens.
2. Tap on the button for how you want to enter the destination.
3. Enter the route point. (Refer to the corresponding section of the
chapter "Specifying a destination" on page 28.)
4. Tap on
(Add).
The selected route point is now shown next to its flow number.
Repeat these steps for each destination that you want to add to your
route.
- 44 -
Navigation
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
5.4.3
Editing route points
Route points can be deleted from a route. The order of the route points
can be changed as you wish.
Note: The starting point (flow number "0") can be neither moved nor
deleted. However you can make another route point into the starting
point provided the Current Position setting was not selected for the
starting point.
►
Tap on the route point that you want to edit.
The context menu contains the following buttons:
Route Point Up: Moves the selected route point further to the front.
(Example: route point 2 becomes route point 1)
Route Point Down: Moves the selected route point further to the back.
(Example: route point 2 becomes route point 3)
Delete: Deletes the selected route point. A dialog window prompts you
to confirm deletion.
5.4.4
Managing routes
You can save each planned route under a particular name.
Note: Only the start point and route points will be saved, not the
calculated route. When you load a saved route, it must be recalculated
before navigation can start.
You can load, rename or delete stored routes.
Saving routes
The ROUTES AND TRACKS window is open. You have entered the
starting point and at least one route point.
1. Tap on Options > Save Route.
2. Enter a name for the route.
3. Tap on
(Save).
The destination is now saved to the SAVED ROUTES AND TRACKS list.
The dialog window closes.
5.4.5
Loading routes or tracks
1. Tap on Options > Saved Routes and Tracks.
The SAVED ROUTES AND TRACKS list opens. It shows all the saved
routes and tracks in alphabetical order.
Navigation
- 45 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
A symbol in front of the name indicates whether it is a route (
or a track (
)
).
If you want to load a route:
2. Tap on the route that you want to load.
3. Tap on
(Load Route).
The ROUTES AND TRACKS window opens. The starting point and the
route points of the loaded route have been entered. For the route
calculation the starting point is replaced by the current position. You
will now be guided to the first route point.
If you want to load a track:
2. Tap on the track that you want to load.
3. Tap on Load Track.
The ROUTES AND TRACKS window opens. The current location is
entered as the starting point. The loaded track is entered as route
point 1. Navigation then leads first to the starting point of the track.
For details about navigating along recorded tracks refer to chapter
"Navigation in Track mode" on page 64.
5.4.6
Calculating and displaying routes
It is possible to calculate and display a planned route on the map even
without GPS reception in order to get an impression of the journey.
The ROUTES AND TRACKS window is open. The starting point and at
least one route point have been entered.
►
Tap on Show Route.
The map opens in Preview mode.
The starting point and the route points are marked by flags. The
distance and the estimated trip time is given for each leg of the
route.
5.4.7
Simulating routes
It is also possible simply to simulate navigation on a planned route.
Note: GPS reception is not necessary for simulation.
If you have planned a multi-leg route, only the first leg will be simulated.
You have calculated and displayed a route.
1. Tap on Options > Simulation.
- 46 -
Navigation
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
►
If you have planned a route with only one route point and the
MyRoutes function is activated, you will be prompted to select
a route for the simulation.
The route will be recalculated for simulation purposes.
2. Tap on the button of the route on which you want to simulate the
navigation.
For more details about the MyRoutes function refer to the chapter
"MyRoutes" on page 41.
Stopping simulation
You can stop simulation at any time.
►
Tap on
(Back).
The ROUTES AND TRACKS window opens.
5.4.8
Route preview
You have calculated and displayed a route. The map is open in
Preview mode.
Route Profile
Route profiles take account of the characteristics and special aspects of
the different modes of transport. For example a route profile for bicycles
will exclude motorways from the route calculation but will include roads
which other vehicles are not allowed to use. And a bicycle profile will
calculate different arrival times than a motorcycle profile.
Note: If you select a pedestrian profile, a type of navigation specially
developed for pedestrians will be started. (Refer to "Navigation in
Pedestrian mode" on page 62.)
►
Tap on the Route Profile button if you want to select a different
route profile.
For details of how to create and select route profiles refer to chapter
"Route profiles" on page 68.
Note: When you load routes which originate from a different provider
than NAVIGON, it may be impossible for you to change the route profile
of this route.
Turn-by-Turn List
If you want to see detailed directions for the route, tap on Options >
Turn-by-Turn List.
Navigation
- 47 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
For details of the functions in the TURN-BY-TURN LIST window refer to
chapter "Turn-by-Turn List" on page 84.
MyRoutes
This section is relevant for you only if your navigation device is one of
the following devices:
►
NAVIGON 40 Easy
►
NAVIGON 40 Plus
►
NAVIGON 40 Premium
►
NAVIGON 40 Premium Live
When the MyRoutes function is activated, the navigation system
calculates up to three routes on the basis of the currently selected route
profile and shows them on the map in different colours (orange, green,
blue) and with a number. For each route there is a button with the same
number and a symbol in the same colour.
When calculating the time of arrival or the trip time, the navigation
system takes account of additional factors such as day of the week and
time of day.
The route which corresponds best to the selected route profile is
marked with "MyRoute".
Note: The MyRoutes function can be used only for routes with only one
route point. For routes with two or more route points only one route is
calculated and displayed, regardless of whether you have activated the
function or not.
Note: Even when the MyRoutes function is activated, sometimes only
one additional route or no additional routes at all can be calculated for a
particular route. No further suggestion is then shown on the button in
question.
Start Navigation
►
Tap on the button of the route which you want to use for the
navigation.
If you select a route for which traffic obstructions have been announced,
the PREVIEW TMC window may open before navigation starts. (Refer to
"Preview TMC" on page 86.)
►
- 48 -
Select whether you want to use the original route (Current Route) or
a detour (Alternative route).
Navigation
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
No GPS reception
If GPS signal reception is not good enough, the following message will
appear: "Waiting for GPS-Signal…"
You have the following options:
►
►
6
Wait. As soon as GPS reception is good enough for determining
your position, the route will be recalculated and navigation will
begin.
Tap on Cancel. The map opens in Preview mode.
Options
Some windows offer options that lead to more functions.
►
Open the Options menu. (Refer to "Button bar" on page 52)
►
Tap on the option you would like to use.
►
If you would like to quit the options list without selecting an option,
tap on the Options button again.
2D/3D: Changes between 2D and 3D mode. The symbol indicates the current
mode.
Add to Route: Opens the route planning. The address specified will be added as
a route point. (Refer to "Tracks and multi-leg routes" on page 43.)
Block: Opens a window in which you can block a section of the route lying
ahead in order to calculate a route which avoids this section, e.g. if you
have heard on the radio of a traffic jam relating to this section. (Refer to
"Block" on page 84.)
Day/Night: Changes between "Day" and "Night" screen modes. The symbol
indicates the current mode.
Delete All: Deletes all destinations in the list (LAST DESTINATIONS list or
FAVOURITES list, depending on where you opened the options). The list
is then empty. A dialog window prompts you to confirm deletion.
Delete: Deletes the selected destination from the LAST DESTINATIONS or
FAVOURITES list or the selected route or track from the SAVED ROUTES
AND TRACKS list. A dialog window prompts you to confirm deletion.
Direct Help: Opens a window in which you can find in quick and uncomplicated
manner the addresses and phone numbers of offices in your direct
vicinity that can be useful in emergencies. (Refer to "Direct Help" on
page 83.)
Options
- 49 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Factory Settings: Resets all settings to the as-delivered state. Routes and
saved destinations are deleted. The software is re-started and behaves
as if started for the first time after being purchased (refer to "Switching
on the navigation device" on page 18).
GPS Status: Opens the GPS STATUS window. Here you can see details
regarding GPS reception. You can also save the data of your current
location. (Refer to "GPS Status, saving the current location" on
page 83.)
Home Address: Saves the selected destination as your home address. You can
then always start navigation to this destination very quickly by tapping in
the NAVIGATION window on Take Me Home.
Interim Destination: Sets the selected point as interim destination. The
navigation system will first guide you to this interim destination.
Afterwards you can continue navigation to your original destination.
Manual: Opens the manual on the navigation device. (Refer to "Manual" on
page 20.)
MyReport: Opens the MYREPORT window. Here you can notify NAVIGON about
any changes to traffic monitoring systems and routing.
MyRoutes: (Only NAVIGON 40 Easy | Plus | Premium | Premium Live):
Opens the map in Preview mode. You are provided with up to three
different suggestions as to how you can continue your journey. Select
one of the routes offered.
New Route: Deletes the starting point and all route points from the ROUTES AND
TRACKS window so that you can plan a new route. If necessary, save
the previously planned route!
Parking: Starts navigation to a car park near the destination.
POI on Your Route: Opens a list with POIs lying on your route. A destination
shown here can be selected as an interim destination and can be
navigated to (refer to "POI on Your Route" on page 77).
Product Information: Here you are shown the version numbers and copyright
details of the hardware and software.
Rename: Opens a window in which you can change the name for the selected
destination or route.
Route Profile: Opens the ROUTE PROFILE window. Here you can view the
options for route planning and, if necessary, change them.
- 50 -
Options
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Routes and Tracks: Opens the ROUTES AND TRACKS window. Here you can plan
routes, manage planned routes and start navigation on a planned route.
(Refer to "Tracks and multi-leg routes" on page 43.)
Save as Favourite: Saves the selected destination to the FAVOURITES list. (Refer
to "Saving destinations" on page 42.)
Save Destination: Saves the selected address in the FAVOURITES list. (Refer to
"Saving destinations" on page 42.)
Save Position: Opens the SAVE DESTINATION AS window. Here you can save
your current position under a certain name in the FAVOURITES list.
Save Route: Opens a window in which you can save the planned route under a
specific name. (Refer to "Saving routes" on page 45.)
Saved Routes and Tracks: Opens a window in which you can load a saved
route or a track.
Settings: Opens the SETTINGS window. Here you can configure the navigation
system. (Refer to "Configuring the navigation system" on page 112.)
Show Map: Opens the map in Standard mode. (Refer to "Map in Standard
mode" on page 54.)
Show on Map: Shows the selected address on the map.
Sightseeing Tours: (Only NAVIGON 40 Easy | Plus | Premium |
Premium Live): Opens the SIGHTSEEING TOURS window. There you can
select a sightseeing tour and start the navigation on a tour. (Refer to
"Sightseeing Tours" on page 81.)
Simulation: Simulates a navigation on the route indicated. This simulation can
be performed without GPS reception. On multi-leg routes, only the first
leg is simulated.
Skip next destination: Tap on this button to omit the next route point. This button
is active only when at least 2 route points still lie ahead of you. (Refer to
"Tracks and multi-leg routes" on page 43.)
Start Recording, Stop Recording: Starts or ends the recording of a track. (Refer
to "Tracks" on page 73.)
Traffic: Opens the TRAFFIC INFORMATION window in which pending reports are
listed. (Refer to "TMC (Traffic Information)" on page 86.)
Turn-by-Turn List: Shows detailed directions for the route, including all points at
which you must turn. (Refer to "Turn-by-Turn List" on page 84.)
Options
- 51 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
7
Working with the map
7.1
Selecting the navigation map
Each country has its own navigation map. Seamless navigation over
several maps on one continent is possible however if a continuous
route can be calculated with the maps saved on the device.
Even if maps of countries in other continents are available on the
navigation device, it can only ever work with the maps of a single
continent.
Tap in the NAVIGATION window on Options > Settings > Map Display in
order to see which maps are currently in use. Here you can also select
a different continent if the navigation device contains any maps of
countries on other continents.
7.2
Button bar
A bar with buttons provides access to all the functions available for
operating the map.
7.2.1
Static button bar
The static button bar is available on the map in Preview mode and
Destination search mode.
If your navigation device is a NAVIGON 40 Essential | Easy, you will
also find the static button bar in other map modes (Standard and
Navigation).
The static button bar can be seen at the bottom edge of the screen.
Back: Closes the navigation. (Refer to "Quitting navigation" on page 66)
- 52 -
Working with the map
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Options: You can use this button during navigation to access many
more functions. (Refer to "Map options in Navigation mode" on
page 65)
Phone: Opens the hands-free module (only NAVIGON 40 Premium |
Premium Live). (Refer to "Handsfree Module" on page 91)
Volume: Opens the volume control function. (Refer to "Volume" on
page 61)
Destination search: Opens the map in Destination search mode.
(Refer to "Map in Destination search mode" on page 66)
7.2.2
Dynamic button bar (1-Click-Menu)
This section is relevant for you only if your navigation device is one of
the following devices:
NAVIGON 40 Plus
NAVIGON 40 Premium
NAVIGON 40 Premium Live
The bar with the buttons is hidden on the map in Standard mode and
Navigation mode. The screen looks tidier and more clearly arranged.
►
Tap on any point on the map.
The dynamic button bar appears at the bottom edge of the screen
instead of the street names.
If navigation is in progress, the POI on Your Route bar will appear at
the top edge. (Refer to "POI on Your Route" on page 77.)
Working with the map
- 53 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Back: Closes the navigation. (Refer to "Quitting navigation" on
page 66.)
Options: You can use this button during navigation to access many
more functions. (Refer to "Map options in Navigation mode" on
page 65.)
Phone: Opens the hands-free module (only NAVIGON 40 Premium |
Premium Live). (Refer to "Handsfree Module" on page 91.)
Volume: Opens the volume control function. (Refer to "Volume" on
page 61.)
Destination search: Opens the map in Destination search mode.
(Refer to "Map in Destination search mode" on page 66.)
7.3
Map in Standard mode
The map is always in Standard mode when you are not navigating,
have not calculated a route and are not searching for a destination on
the map.
Under the following circumstances the map switches automatically to
Standard mode:
►
►
- 54 -
You begin a trip while the NAVIGATION window is open. The switch
takes place after only a short while.
You reach the destination of a navigation in Vehicle mode.
Working with the map
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
To open the map:
►
In the NAVIGATION window tap on Show Map.
Note: If GPS reception is not good enough to establish your location, the
map will be opened in Destination search mode.
The following features are typical for this view:
►
►
Indicated in the middle of the lower third is your current position
(orange arrow). The map view follows your movements so that your
position is always visible on the screen.
The scale of the map changes according to your speed.
Map options in Standard mode
NAVIGON 40 Plus | Premium | Premium Live:
1. Tap on any point on the map.
The button bar appears.
2. Tap on
(Options).
NAVIGON 40 Essential | Easy:
►
Tap on Options.
A window with several buttons opens.
The most important functions for navigation can be reached via buttons
with symbols.
Other functions are found by tapping on one of the buttons Destination,
Route, Services or General.
A description of all available options can be found in the chapter
"Options" on page 49.
Working with the map
- 55 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
7.4
Map in Preview mode
You have entered a destination and tapped on Start Navigation.
-orYou have planned or loaded a route and tapped on Show Route.
The map opens in Preview mode.
1
When the MyRoutes function is activated, up to three numbered routes
are indicated on the map in different colours (orange, green, blue).
In the following cases only one route is shown:
2
►
The MyRoutes function is deactivated.
►
You have planned a route with more than one route point.
►
A route profile with the Pedestrian speed profile is active.
►
The route includes a track.
The destination is marked with a little flag.
If you display a planned or loaded route, the starting point and each
route point will be marked with a little flag.
In the case of a multi-leg route, the distance and the estimated driving
time for each leg are displayed.
3
The current route profile is indicated on the
(Route Profile) button.
The symbol illustrates the mode of transport on which the profile is
based. (Refer to "Route profiles" on page 68.)
►
4
Tap on the symbol to select a different route profile.
The current position is indicated (orange arrow).
If you display a planned or loaded route and the specified starting point
is not your current location, then it is possible that your current position
will not be shown on the preview.
- 56 -
Working with the map
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
5
(Only NAVIGON 40 Easy | Plus | Premium | Premium Live): For each
route (orange, green, blue) there is a button with the same number and
a symbol in the same colour. Indicated on each button are the
estimated time of arrival, the total distance and the estimated duration
of the particular route.
If traffic messages exist for a route, the number of messages is
indicated in a small traffic sign on the button. The reported obstructions
are also indicated on the route.
The route which corresponds best to the selected route profile is
marked with "MyRoute".
If the MyRoutes function is not activated, only one route is presented.
As soon as you tap on a button, navigation along the route in question
will start.
►
►
Tap on the
(Route Profile) button (refer to the figure, point 3)
in order to select a different route profile.
To start the navigation, tap on the button for the route (see figure,
point 5) you want to use for the navigation.
If you display a planned or loaded route, the route may be
recalculated. The starting point for the calculation will now be your
current location. You will first be guided to the first route point
entered.
►
►
7.5
Tap on Options > Turn-by-Turn List to view detailed directions for
the route. (Refer to "Turn-by-Turn List" on page 84.)
Tap on
(Destination search) in order to view the map in
Destination search mode. (Refer to "Map in Destination search
mode" on page 66.)
Map in Navigation mode
How you are guided to your destination depends on various factors (the
route profile selected, your current location, the type of route planning,
etc.). Your navigation system automatically selects the optimum
method.
7.5.1
Navigation in Vehicle mode
After the route was shown in Preview mode, navigation was started.
The map opens in Navigation mode.
Working with the map
- 57 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
1
If any information is available about the sign which you should follow, it
will be shown at the top edge of the screen.
2
The POI on Your Route bar will open (refer to "POI on Your Route" on
page 77). This button is not visible when a sign is being shown (see
point 1).
►
Tap on the display to hide the sign.
For a description of the POI on Your Route function refer to chapter
"POI on Your Route" on page 77.
3
(Only NAVIGON 40 Easy | Plus | Premium | Premium Live): Possible
speed limits may be shown here.
4
The route is highlighted in orange.
5
When two manoeuvres need to be executed in quick succession, the
small arrow box indicates the second manoeuvre to be executed.
6
The large arrow box shows a diagram of the next junction which you
should turn on to. The distance remaining to this junction is indicated
underneath.
- 58 -
Working with the map
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
As you get closer to the junction you will see a spot diagram in addition
to the distance:
The nearer you get to the junction, the more yellow spots are displayed.
If you don't have to change direction for a long time, you will see only a
straight arrow. The distance you must continue straight on is indicated
underneath the arrow.
►
7
Tap on the large arrow box to hear current route instructions.
The Traffic Information box opens if a reported traffic obstruction
affects your route.
If a distance is indicated in the Traffic Information box, no detour route
was calculated yet for the traffic obstruction in question.
►
Tap on the Traffic Information box in order to open the
PREVIEW TMC window. It shows a map view with the route section
affected by the message and a possible detour.
If no distance is indicated, all the obstructions which are reported for
your route and would lead to a loss of time will be avoided.
►
Tap on the Traffic Information box in order to open the TRAFFIC
INFORMATION window. (Refer to "Displaying traffic information" on
page 88.)
Note: The calculation of detour routes to avoid reported traffic
obstructions can be performed automatically. (Refer to "TMC Settings"
on page 89.)
8
When you get close to your destination, the Parking button will appear.
If you tap on the Parking box you will be given two options:
►
►
You can select a car park from where you can then continue on
foot.
When you have parked your vehicle, you can save the current
position and continue the navigation on foot.
For a description of the Parking function refer to chapter "Parking near
the destination" on page 75.
Working with the map
- 59 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
9
(Only NAVIGON 40 Easy | Plus | Premium | Premium Live): When
you get close to a NAVIGON Sightseeing sight, the NAVIGON
Sightseeing button will appear instead of the height above sea level and
the speed (point 12). The distance indicated on the button tells you how
far away the sight is (beeline).
If you tap on the NAVIGON Sightseeing button, the DESTINATION INFO
window will open (refer to "Displaying information about a NAVIGON
Sightseeing sight" on page 80).
For a description of the NAVIGON Sightseeing function refer to chapter
"NAVIGON Sightseeing" on page 79.
10
Ahead of many junctions the information from points 12 and 13 is
hidden. Instead you are shown which lanes lead to your destination.
►
11
Tap on the box in order to hide the lane information.
Your current position is indicated on the map (orange arrow). The
section of the map displayed changes continually so that your current
position is always in view on the map.
12
The height above sea level and the current speed are shown here.
13
In the Total box you can see the distance remaining to the destination,
the estimated duration of the trip and the estimated time of arrival.
►
►
14
Tap on the arrival time if you want to see the estimated driving time
instead.
Tap once again on the info box if you want to see the estimated
time of arrival.
If you are navigating a multi-leg route, you will see the remaining
distance to the next interim destination and the estimated time of arrival
in the Next box.
►
►
Tap on the arrival time if you want to see the estimated driving time
instead.
Tap once again on the info box if you want to see the estimated
time of arrival.
15
The name of the route section that you need to drive onto next is shown
in the upper road box.
16
The name of the section you are currently driving on is shown in the
lower road box.
Note: The displays of many of the above mentioned areas can be
configured in Options > Settings > Navigation. Some displays will only
function if the required information is available on the map.
Note: If you tap on the large arrow box, the current route instruction will
be repeated.
- 60 -
Working with the map
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Note: If you leave the road system covered by the map, the navigation
will switch to Offroad mode. (Refer to "Navigation in Offroad mode" on
page 65.)
►
►
Tap on Options > Route > Turn-by-Turn List in order to view a turnby-turn list. (Refer to "Turn-by-Turn List" on page 84.)
Tap on
(Destination search) in order to view the map in
Destination search mode. (Refer to "Map in Destination search
mode" on page 66.)
Volume
The volume of the spoken driving instructions can be adjusted during
navigation.
1. Tap on
(Volume).
The volume bar opens. It contains three buttons for adjusting the
volume:
(Louder),
2. Tap on
(Quieter),
(Volume on/off).
(Volume) again or wait a few seconds.
The volume bar closes.
Reality View
This section is relevant for you only if your navigation device is one of
the following devices:
►
NAVIGON 40 Easy
►
NAVIGON 40 Plus
►
NAVIGON 40 Premium
►
NAVIGON 40 Premium Live
The map switches to Reality View mode when you approach one of the
following points while driving on the motorway:
►
a motorway junction
►
a three-leg motorway junction
►
the exit you must take to leave the motorway
Working with the map
- 61 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
The Reality View mode shows with greater clarity the signposting and
lanes you must follow.
This display does not change until you have passed the spot indicated.
The map will then change back to Navigation mode.
►
If you want to change to Navigation mode before then, just tap on
any point on the map.
Note: The Reality View mode is not available for all motorway
junctions and three-leg motorway junctions. Availability depends on the
map material used.
7.5.2
Navigation in Pedestrian mode
This section is relevant for you only if your navigation device is one of
the following devices:
►
NAVIGON 40 Easy
►
NAVIGON 40 Plus
►
NAVIGON 40 Premium
►
NAVIGON 40 Premium Live
This mode is active if you have selected a pedestrian route profile for
the navigation. These profiles can be identified by the
symbol.
(Pedestrian)
After the route was shown in Preview mode, navigation was started.
You receive a route proposal which is calculated on the basis of the
digitalised road system. You are also shown in which direction your
destination lies. If you leave the proposed route, for example in order to
take a more pleasant route through a park, you will still see at all times
the direction in which your destination lies.
- 62 -
Working with the map
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Please note:
►
►
►
►
►
You will receive no navigation instructions. Instead you will receive
a message when you are getting close to the destination.
The map view follows your movements so that your position is
always visible on the screen.
If you leave the calculated route, the route will not be recalculated
automatically.
If you are navigating on a route and more route points are still to
follow, navigation to the next route point will be started immediately
after the message.
Traffic messages are not taken into account.
Note: In pedestrian mode you must take care to hold the device without
covering it at the top. The GPS receiver is located there and its
reception could be impaired.
1
The scale of the map section shown is indicated here. The length of the
ruler corresponds to the distance indicated.
2
The route which was calculated using the digitalised road system is
marked in orange.
3
The current position is indicated (orange arrow). You can see in which
direction you are moving.
4
The part of the route which you have already covered is marked in
green.
5
The compass indicates where north is.
6
The direction in which your destination lies is indicated (red triangle).
7
In this box you are shown the distance remaining to the destination
(beeline).
Working with the map
- 63 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Operating the map
Zoom Out: The map section shown becomes larger, but you will see
fewer details.
Zoom In: The map section becomes smaller, but you will see more
details.
Centre the position: During pedestrian navigation you can shift the
visible map section in order to view the surrounding area on the map.
This may mean that your current position can no longer be seen on the
visible section of the map.
►
Tap on the Centre the position button if your current position can no
longer be seen on the visible section of the map.
Your current position will be shown again on the map.
Recalculate route: Recalculates the route. Use this function if you have
wandered far from the calculated route and would like a new route
proposal.
7.5.3
Navigation in Track mode
This mode becomes active if you have planned a route with a track for
the navigation. (Refer to "Tracks and multi-leg routes" on page 43.)
After the route was shown in Preview mode, navigation was started.
First the navigation guides you from your current location to the
beginning of the loaded track. This navigation corresponds to the
navigation of the selected route profile. (Refer to "Navigation in Vehicle
mode" on page 57 and to "Navigation in Pedestrian mode" on page 62.)
As soon as the first recorded point of the track is reached, the
navigation switches to Track mode.
Navigation in Track mode works like navigation in Pedestrian mode.
(Refer to "Navigation in Pedestrian mode" on page 62.)
There are only a few differences:
►
►
- 64 -
The Recalculate route function is not available.
If more route points follow after the track, the navigation will switch
back to the originally selected mode.
Working with the map
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
7.5.4
Navigation in Offroad mode
Note: This mode does not become active if you have selected a
pedestrian route profile for the navigation. These profiles can be
identified by the
(Pedestrian) symbol.
Nor does it become active if you are navigating along a track. (Refer to
"Navigation in Track mode" on page 64.)
If you enter a destination which lies off the digitalised road system, the
navigation will guide you first in Vehicle mode to the point of the
digitalised road system that lies nearest to the destination. From here
the navigation then continues in Offroad mode.
If the current position at the beginning of navigation lies off the
digitalised road system, the navigation will guide you first in Offroad
mode to the nearest point of the digitalised road system. From here the
navigation then continues in Vehicle mode.
Navigation in Track mode works like navigation in Pedestrian mode.
(Refer to "Navigation in Pedestrian mode" on page 62.)
There are only a few differences:
7.5.5
►
The part of the route already covered is not shown.
►
The Recalculate route function is not available.
Map options in Navigation mode
NAVIGON 40 Plus | Premium | Premium Live:
1. Tap on any point on the map.
The button bar appears.
2. Tap on
(Options).
NAVIGON 40 Essential | Easy:
►
Tap on Options.
A window with several buttons opens.
The most important functions for navigation can be reached via buttons
with symbols.
Other functions are found by tapping on one of the buttons Destination,
Route, Services or General.
A description of all available options can be found in the chapter
"Options" on page 49.
Working with the map
- 65 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
7.5.6
Quitting navigation
You quit the navigation in the same way in all modes:
►
7.6
Tap on
(Back) in order to quit navigation. A dialog box will
prompt you to confirm.
Map in Destination search mode
The map is always in Destination search mode, when a pair of cross
hairs are to be seen. Indicated in the address box are the coordinates
and, where applicable, the name of the street under the cross hairs.
When you are driving, the map does not change. It is always orientated
with north at the top.
Zoom Out: The map section shown becomes larger, but you will see
fewer details.
Zoom In: The map section becomes smaller, but you will see more
details.
Zoom Mode: When this button is active you can mark out a section of
the map with your finger.
Mark out the section from upper left to bottom right to zoom in until the
section fills the screen.
Mark out the map section from bottom right to top left to zoom out.
Pan Mode: When this button is active you can change the section of
map shown with your finger. Simply drag the map in the desired
direction.
- 66 -
Working with the map
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Entire Route: Zooms the map so that the entire route is visible.
Current Position: Selects the section of map displayed so that the
current location is at the centre.
7.6.1
Operating in Destination search mode
1. Tap on the point to which you want to navigate.
The destination that you have selected appears under the cross
hairs.
The geographical coordinates of the destination and the
corresponding address are shown in the bottom third of the screen.
2. Tap on
(OK).
Buttons with various functions will be displayed.
Take Me There: Starts navigation to the selected point. If you are currently
navigating, this route navigation will be cancelled.
MyReport: Opens the MYREPORT window. Here you can notify NAVIGON about
any changes to traffic monitoring systems and routing.
Interim Destination: Sets the selected point as interim destination. The
navigation system will first guide you to this interim destination.
Afterwards you can continue navigation to your original destination.
This function is only active during navigation.
Add to Route: Adds the selected point to the route planning as the last point.
Navigation will then continue to this point after you have reached the
original destination or the other route points.
Save: Opens the SAVE DESTINATION AS window. You can enter a name under
which the selected point will be saved in the FAVOURITES list. (Refer to
"Saving destinations" on page 42.)
Search Nearby: Opens the POI NEARBY window. Here you can search for
destinations near the selected point. (Refer to "POI nearby" on
page 32.)
►
Tap on
(Back) in order to quit Destination search mode.
You will be returned to the window from which you started this
mode.
Working with the map
- 67 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
8
Useful functions
8.1
Route profiles
Route profiles define the characteristics and special aspects of the
different modes of transport which are to be taken into account when
calculating routes. For example a route profile for bicycles will exclude
motorways from the route calculation but will include roads which other
vehicles are not allowed to use. And different arrival times will be
calculated for a bicycle than for a motorcycle for example.
8.1.1
Route profile settings
A route profile is made up of several settings:
►
►
►
►
►
Speed Profile: Defines the mode of transport (e.g. Bicycle,
Pedestrian, Car, ...).
Type of Route: Defines the type of route which is to be calculated
(e.g. Short Route, Fast Route, ...).
Consider Traffic Information: defines whether traffic messages are
to be considered when calculating the route
Motorways, Ferries, Restricted Areas: Defines whether these types
of road are allowed to be used.
Use of Toll Roads: defines whether toll roads are allowed to be
used when calculating the route
►
Tap on the
(Edit) button.
The USE OF TOLL ROADS window opens.
►
Adapt the individual settings to your requirements (Yes, No, Ask
before). (Refer also to Configuring the navigation system on
page 112.)
If you activate the Ask before setting, every time your route can
take a toll road you will be prompted to make the corresponding
setting(s).
For each setting there is a
(Help) button. When you tap on it you
will see an exact definition of the setting in question.
The number of possible settings depends on the selected speed profile.
For example, for the Pedestrian speed profile there are no Motorways
and Use of Toll Roads settings.
8.1.2
NAVIGON basic profiles
A basic profile is already defined for each speed profile.
Bicycle
- 68 -
Useful functions
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Pedestrian (only NAVIGON 40 Easy | Plus | Premium |
Premium Live)
Lorry
Motorbike
Car
The speed profile of a basic profile cannot be changed. You can adapt
the other settings to your requirements.
Basic profiles cannot be renamed or deleted.
To have a choice of different profiles for example for several cars, you
can create your own route profiles.
8.1.3
Creating a new route profile
You can create your own route profiles. This makes sense for example
if you own two cars and only one has a prepaid toll disc for Austrian
motorways.
1. Tap on Options > Settings.
If the map is open in Standard mode, tap on Options > General >
Settings.
2. Tap on the
(Current Route Profile) button. This button can also
show a different symbol.
3. Tap on the name of the route profile which you want to take as
basis for the new profile.
4. Tap on Options > Copy.
5. Enter a name for the route profile.
6. Tap on Save.
7. Adapt the route profile to your requirements.
8. Tap on OK.
The new route profile is shown in the ROUTE PROFILES list.
8.1.4
Selecting a route profile
1. Tap on Options > Settings >
(Current Route Profile).
If the map is open in Standard mode, tap on Options > Route >
Current Route Profile:.
2. Tap on the name of the route profile which you want to use.
3. Tap on
Useful functions
(Back).
- 69 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
8.1.5
Managing route profiles
User-defined route profiles can be edited, renamed and deleted.
Editing a route profile
1. Tap on Options > Settings.
If the map is open in Standard mode, tap on Options > General >
Settings.
2. Tap on the
(Current Route Profile) button. This button can also
show a different symbol.
3. Tap on the
want to edit.
(Edit) button alongside the route profile that you
4. Make the required settings.
5. Tap on OK.
The Use of Toll Roads setting is comprised of several individual
settings. For example for each country with toll motorways you can
select whether you want to use these roads for the navigation.
1. Tap on the
setting.
(Edit) button alongside the Use of Toll Roads
The USE OF TOLL ROADS window opens.
2. Adapt the individual settings to your requirements (Yes, No, Ask
before).
If you activate the Ask before setting, each time the route preview
wants to calculate a route with a toll road you will be asked whether
you want to use the type of toll roads in question. You can then lay
down this setting for future journeys as well.
Renaming a route profile
1. Tap on Options > Settings.
If the map is open in Standard mode, tap on Options > General >
Settings.
(Current Route Profile) button. This button can also
2. Tap on the
show a different symbol.
3. Tap on the name of the route profile which you want to rename.
4. Tap on Options > Rename.
5. Enter the new name for the route profile.
6. Tap on Save.
Note: Basic profiles cannot be renamed.
- 70 -
Useful functions
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Deleting a route profile
1. Tap on Options > Settings.
If the map is open in Standard mode, tap on Options > General >
Settings.
2. Tap on the
(Current Route Profile) button. This button can also
show a different symbol.
3. Tap on the name of the route profile which you want to delete.
4. Tap on Options > Delete.
5. A dialog window prompts you to confirm deletion.
6. Tap on Yes.
Note: Basic profiles cannot be deleted.
8.2
MyPOIs: My POIs
You can create files with your own POIs. These files have to be made
available to your navigation system in a specific folder.
If you want to choose from your own POIs, you will find them under the
MyPOIs category of POIs. Each file with your own POIs is listed as a
sub-category. Each sub-category can have a personally created symbol
for representing your destinations on the map.
Note: The navigation device can import a maximum of 10,000 POIs.
These destinations are allowed to be shared among a maximum of
40 sub-categories.
8.2.1
Creating your own destinations
1. Open an empty document in an editor which can save the files in
UTF8 code (e.g. MS Notepad, Microsoft Word).
Note: The following description is based on the use of MS Notepad as
editor. If a different editor is used, the saving of the file and its UTF-8
coding (point 4-9) may differ from this description.
2. For each destination create a data record (one line) with the
following form:
►
►
Useful functions
Longitude. Begin the entry with a minus sign if you want to
enter a western degree of longitude. The longitude must be
entered as a decimal number with a dot as the decimal sign.
Comma (as list separator)
- 71 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
►
►
►
Latitude. Begin the entry with a minus sign if you want to enter
a southern degree of latitude. The latitude must be entered as a
decimal number with a dot as the decimal sign.
Comma (as list separator)
Name of the destination. Any name is possible, but no commas
are allowed. If the use of a comma is indispensable, precede it
with a backslash ('\').
►
Comma (as list separator)
►
PHONENUMBER=
►
A phone number. This entry can remain empty.
►
Tilde ('~')
►
Additional information. This entry can remain empty.
►
Enter (in order to begin a new data record)
The address does not have to be included in the data record. It is
shown automatically when you select this POI for navigation. If you
enter additional information, it will appear under the address.
Example:
9.94302,49.79906,NAVIGON AG,PHONENUMBER=+49 931~Best
Navigation Devices
3. Repeat step 2 for each destination you want to save in this file.
4. Click on File > Save.
5. Select a folder in which you want to save the data.
6. In the File type box select the All Files option.
7. In the file name box enter a name of your choice followed by '.csv',
e.g. 'XYZ.csv'. Please note that the file name will appear in the
navigation system as a sub-category! This means that if you save a
file under the name 'XYZ.csv', the destinations of this file will appear
in the sub-category XYZ.
8. In the Encoding box select the UTF-8 option.
9. Tap on Save.
8.2.2
Symbols for your own POIs
For each sub-category of your own POIs you can create a symbol
which is used to represent the destinations of this sub-category on the
map.
These symbols must be graphic files with the following characteristics:
►
File format bmp (Bitmap) or png (Portable Network Graphic)
►
Size max. 40x25 pixels
The graphic files must be saved in the same folder as the related files
with the POIs.
The file name must be the same as the name of the category.
- 72 -
Useful functions
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Example:
Destinations of the XYZ sub-category are saved in the 'XYZ.csv' file.
They are represented on the map by the 'XYZ.bmp'symbol.
8.2.3
POI-Import: Importing your own POIs onto the navigation
device
The files you have created with your own POIs and the related symbols
must still be transferred to the navigation device. This is easy and
convenient to do with the NAVIGON Fresh software which you can
install on your computer using NAVIGON Suite or download free of
charge from our website www.navigon.com/fresh.
8.3
Screenshots
You can create and save screenshots of the content currently shown on
the screen at any moment.
8.3.1
Enabling screenshots
1. In the NAVIGATION window tap on Options > Settings > General >
Enable Screenshots.
2. Select whether you want to enable screenshots (Yes) or not (No).
(Screenshots) button appears at the bottom right edge of
The
the screen.
8.3.2
Creating a screenshot
►
Tap on the
(Screenshots) button.
The screen is saved as a graphic. The
not shown in the figure.
(Screenshots) button is
The screenshots are saved in the \ScreenShots folder. This folder can
be found either in the internal memory of the navigation device, on the
inserted memory card or in both memories.
8.4
Tracks
This section is relevant for you only if your navigation device is one of
the following devices:
►
NAVIGON 40 Easy
►
NAVIGON 40 Plus
►
NAVIGON 40 Premium
►
NAVIGON 40 Premium Live
Useful functions
- 73 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
You can record any section of a route you take, even if it lies off the
digitalised road system.
You can record for example a bicycle tour and follow the same route
again some time later.
Tracks are saved in KML data format. KML is a widely used data
format. You can also play back your tracks for example in Google Earth
on your PC.
Recording a track
You can record a track when the map is open in Navigation mode or in
Standard mode.
1. Tap on Options > Services > Start Recording.
The START RECORDING window opens.
2. Enter a name for the planned recording.
Note: Only Latin characters are available for naming tracks.
3. Tap on Start Recording.
Starting from your current position, the navigation device will record
the entire route you now take.
The
(Record Track) symbol appears at the top right edge of the
screen throughout the recording.
The recorded route is saved in the SAVED ROUTES AND TRACKS list
in KML data format. It can be loaded again from there at any time.
Stopping the recording
1. Tap on Options > Services > Stop Recording.
The recording is stopped. The recorded route is saved in the SAVED
ROUTES AND TRACKS list in KML data format. It can be loaded again
from there at any time.
Note: Switching off the navigation device will only interrupt the track
recording. If you want to stop the recording, you must proceed as
described above.
Using a track for navigation
You can load saved tracks as part of planning a route. (Refer to
"Loading routes or tracks" on page 45.)
Note: All tracks that have been saved in KML data format are suitable
for route planning. Use NAVIGON Fresh in order to load tracks from
other suppliers onto your navigation system.
- 74 -
Useful functions
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Note: When you are navigating along a recorded track, any incoming
TMC messages will not be checked to see if they concern the track in
question.
8.5
Parking near the destination
When you get close to your destination, the
(Parking) button
will appear on the screen. This button also remains visible after you
have reached your destination as long as you stay close to the
destination and the map is not closed.
The following scenarios are imaginable:
Continuing on foot
This section is relevant for you only if your navigation device is one of
the following devices:
►
NAVIGON 40 Easy
►
NAVIGON 40 Plus
►
NAVIGON 40 Premium
►
NAVIGON 40 Premium Live
You see a car park, park your vehicle and want to continue to the
destination on foot.
1. Tap on the
(Parking) button.
2. Tap on Pedestrian mode.
The following message appears: "Your current position has been
saved. You will find it in the 'Favourites' list as 'My Vehicle'. This
enables you to easily find the way back to your vehicle."
3. Tap on OK.
The position of your vehicle is marked on the map by an asterisk in
orange.
The navigation continues to guide you to the destination in
Pedestrian mode.
Searching for a car park
You want to be guided to a car park near the destination. From there
you want to walk to the destination.
1. Tap on the
(Parking) button.
2. Tap on Parking Close to Destination.
Useful functions
- 75 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
A list opens. You are shown possible car parks in order of distance
from your destination.
3. Tap on the car park where you want to park your vehicle.
You are shown more information about this car park.
4. Tap on Add.
5. The navigation now guides to the selected car park in the mode
corresponding to the selected route profile. When you arrive there,
the following message appears: "Your current position has been
saved. You will find it in the 'Favourites' list as 'My Vehicle'. This
enables you to easily find the way back to your vehicle."
6. Tap on OK.
The position of your vehicle is marked on the map by an asterisk in
orange.
The navigation continues to guide you to the destination in Pedestrian
mode.
Back to the destination
You have reached your destination. Navigation has ended. For some
reason, however, you carry on driving, perhaps because you were
unable to find a place to stop. Now you want to be guided back to the
destination.
1. Tap on the
(Parking) button.
2. Tap on Last Destination.
The navigation now guides you back to the original destination in the
mode corresponding to the selected route profile.
NAVIGON Clever Parking: Current information about parking
options
Some parking options are marked by a small asterisk (e.g.
). There
is more information available for these parking options, e.g. opening
times or the number of parking spaces for women or the number of
parking spaces for the handicapped.
This information is becoming available for more and more parking
options. Regular updates of this information can easily be obtained via
the NAVIGON Fresh software. NAVIGON Fresh can be downloaded
free of charge from the website www.navigon.com/fresh.
8.6
Nearby
During the navigation, or after having opened the map using the Show
Map button, you can have POIs, Favourites and traffic information of
the current map view shown in a clearly arranged list.
- 76 -
Useful functions
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Note: This function is not available if the map was opened in one of the
modes Destination search, Preview or Reality View.
NAVIGON 40 Plus | Premium | Premium Live:
1. Tap on any point on the map.
The button bar appears.
►
Tap on any point on the map.
NAVIGON 40 Essential | Easy:
1. Tap on any point on the map.
The NEARBY list opens. It contains POIs, Favourites or traffic messages
of the current map view.
2. Tap on an entry in the list in order to receive detailed information
about it.
You have the following options:
►
Tap on Interim Destination in order to set the selected point as an
interim destination. The navigation system will first guide you to this
interim destination. Afterwards you can continue navigation to your
original destination. The Interim Destination button is available in
navigation mode only.
►
Tap on Start Navigation in order to navigate to the selected point.
►
Tap on Cancel in order to close the list again.
Note: The Nearby function is available only if GPS reception is good
enough.
8.7
POI on Your Route
Note: This function is available only during navigation in Vehicle mode
(refer to "Navigation in Vehicle mode" on page 57).
You can stipulate 3 categories of POI for the POI on Your Route
function. POIs which lie along your route and match one of these
categories can be quickly displayed and selected as an interim
destination during the navigation.
8.7.1
Displaying POIs along the route
1. Tap on the
(POI on Your Route) button which appears at
the top left of the map (refer to point 2 in "Navigation in Vehicle
mode" on page 57).
The POI on Your Route bar opens.
Useful functions
- 77 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
It shows symbols of the 3 stipulated categories of POI. The distance
to the nearest POI in each category is indicated. The marking along
the route also indicates whether the POI lies on the right (
) or
) in driving direction.
left (
Note: The POI on Your Route bar closes after a few seconds.
If you want the bar to remain open, tap on the
(Fix) button. The
(Fixed). The bar will now remain visible until
button changes to
you open the POI ON YOUR ROUTE list.
2. Tap on one of the categories in order to show a list with more POIs
in this category.
The POI ON YOUR ROUTE list opens.
1
Symbols of those categories in which POIs are available are shown at
the top edge of the screen. The symbol of the currently selected
category is highlighted.
►
Tap on the symbol of the category whose POIs you want to have
displayed.
2
The list contains the next 5 POIs, sorted by distance in descending
order, which lie along your route and are in the stipulated category. The
nearest POI is therefore the lowest entry in the list.
3
Additional information about each POI in the list can be displayed.
►
- 78 -
Tap on the
(Info) button on the right alongside the
corresponding POI (refer also to "Information about the destination"
on page 36).
Useful functions
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
4
8.7.2
The route and your current position are shown schematically on the left
edge of the screen. The markings along the route indicate the distance
of the listed destinations from your position. The orange-coloured
markings indicate whether the respective destination is on the right
(
) or on the left (
) in driving direction.
Navigating to one of the destinations
►
Tap in the list on the destination to which you want to navigate.
The selected destination will be inserted as an interim destination.
The system recalculates the route. Navigation to the original
destination will be continued after reaching the interim destination.
8.7.3
Selecting categories
You can stipulate which 3 categories or sub-categories are to be
available for the POIs along the route.
1. Tap in the POI ON YOUR ROUTE list on Settings.
The SETTINGS: POI ON YOUR ROUTE window opens.
2. Tap on the
(List) button alongside the category you want.
The list of POI categories will open.
If any sub-categories exist for a category, the
(List) button will
be shown again alongside it. Tap on this button to show the subcategories.
3. Select a category.
4. Tap on OK.
The SETTINGS: POI ON YOUR ROUTE window opens.
5. Tap on OK.
6. The POI ON YOUR ROUTE list opens. If there are POIs of the newly
selected category along the route, they will already appear in the
list.
7. Tap on
(Back) in order to close the list.
The map opens.
8.8
NAVIGON Sightseeing
This section is relevant for you only if your navigation device is one of
the following devices:
►
NAVIGON 40 Easy
►
NAVIGON 40 Plus
►
NAVIGON 40 Premium
►
NAVIGON 40 Premium Live
Useful functions
- 79 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
NAVIGON Sightseeing sights are a special category of POI. You can
be pointed to these sights when you get close to them.
Note: Pointers are possible only during navigation or when the map is
opened in Standard mode.
Activating pointers to NAVIGON Sightseeing sights
You can select whether or how you want to be pointed to NAVIGON
Sightseeing sights.
1. In the NAVIGATION window tap on Options > Settings > Navigation >
Info about 'NAVIGON Sightseeing' Destinations.
2. Select one of the following settings:
►
No: You will not be pointed to NAVIGON Sightseeing sights.
►
Only on the Screen: When you get close to a NAVIGON
(NAVIGON Sightseeing) button
Sightseeing sight, the
will appear on the map and can be used to open the
DESTINATION INFO window.
►
Audio Info for Important Destinations: For nationally known
sights, a description will be read out as soon as the
(NAVIGON Sightseeing) button appears.
►
Audio Info for All Destinations: For all sights in the category, a
description will be read out as soon as the
Sightseeing) button appears.
(NAVIGON
Note: Particularly detailed information about each NAVIGON
Sightseeing sight can easily be purchased via the NAVIGON Fresh
software. NAVIGON Fresh can be downloaded free of charge from the
website www.navigon.com/fresh.
Note: Descriptions cannot be read out in every language. In this case
the two settings Audio Info for Important Destinations and Audio Info for
All Destinations are not available.
Note: During navigation in Pedestrian mode you will receive a pointer
only when your destination is a NAVIGON Sightseeing destination and
you are getting close to your destination.
Displaying information about a NAVIGON Sightseeing sight
►
- 80 -
You have chosen to be informed about NAVIGON Sightseeing
sights (refer to "Activating pointers to NAVIGON Sightseeing sights"
on page 80).
Useful functions
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
►
The map is open in Navigation or Standard mode.
When you get close to a NAVIGON Sightseeing sight, the
(NAVIGON Sightseeing) button will appear on the map. The
distance indicated on the button tells you how far away the destination
is (beeline). Depending on your settings, a description of the destination
will be read out in addition.
►
Tap on the
(NAVIGON Sightseeing) button.
The DESTINATION INFO window opens. In addition to a description it
contains information such as the address, phone number or opening
hours.
You have the following options:
►
►
►
►
Tap on the
(Audio Info) button in order to start or stop the
description being read out.
Tap on the
on the map.
(Show on Map) button in order to show the sight
Tap on the
(Save Destination) button in order to save the sight
in the FAVOURITES list.
Tap on the picture of the sight to show it in full screen mode.
Tap on the picture again in order to close full screen mode.
►
►
►
8.9
During navigation: Tap on Interim Destination on order to insert the
sight as an interim destination.
If there is no navigation in progress: Tap on Start Navigation in
order to start the navigation to this sight.
Tap on Close in order to close the DESTINATION INFO window again
and return to the map view.
Sightseeing Tours
This section is relevant for you only if your navigation device is one of
the following devices:
►
NAVIGON 40 Easy
►
NAVIGON 40 Plus
►
NAVIGON 40 Premium
►
NAVIGON 40 Premium Live
Sightseeing Tours are predefined routes with destinations of scenic,
cultural or touristic interest which are sorted according to various
categories.
Useful functions
- 81 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Note: The navigation software contains only a limited number of
sightseeing tours. An update with more than 100 sightseeing tours can
be purchased via NAVIGON Fresh. The NAVIGON Fresh software can
be downloaded free of charge from the webseite
www.navigon.com/fresh.
1. In the NAVIGATION window, tap on Options > Sightseeing Tours.
The SIGHTSEEING TOURS window opens.
2. Enter the country in which you want to search for sightseeing tours
(refer to "Specifying the country in which the destination is situated"
on page 29).
3. Select a category from which you would like to find a route.
The NAME list opens. It contains routes from the specified category,
sorted alphabetically.
4. Tap on the name of the route.
The DETAILS OF THE ROUTE window opens.
It shows the name of the route, the length of the route, the
estimated driving time and a short description of the route.
►
Tap on Info to receive a detailed description of the route.
Tap on Close to reopen the DETAILS OF THE ROUTE window.
On the Begin at… button you are told at which route point the route
starts:
►
►
First: You are guided from your current position to the advised
starting point of the sightseeing tour. Navigation on the selected
tour then begins.
Nearest: You are guided from your current position to the most
favourable point along the route of the selected tour. Navigation on
the selected tour then begins.
5. Tap on Begin at… in order to select the alternative setting.
6. Tap on Plan route.
The ROUTES AND TRACKS window will open (refer to "Tracks and
multi-leg routes" on page 43).
Here you can obtain an overview of the various legs of the selected
tour and of the order the legs will follow.
Note: The list of route points in the ROUTES AND TRACKS window is for
orientation purposes only. It is impossible in this list to change the order
of the route points, delete route points or add new route points.
►
Tap on Show Route.
The map opens in Preview mode and you can start the navigation
on the route.
- 82 -
Useful functions
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Note: Detailed information about starting the navigation and about the
map in Preview mode can be found in the chapter "Map in Preview
mode" on page 56.
8.10
Direct Help
If you arrive at the scene of an accident or have an accident yourself, it
may be necessary to call for emergency aid and to give the answering
office your current location.
►
Tap on Options > Services > Direct Help.
The DIRECT HELP window opens.
If GPS reception is good enough, the address and the geographic
coordinates of your current location will be indicated.
►
Tap on
(Show on Map) if you want to view your current
location on the map.
In the bottom half of the window you will find the buttons for
4 categories: Petrol Station, Police Station, Hospital, Pharmacy.
►
Tap on the corresponding button.
The nearest help point in the selected category will be indicated.
You are shown the name, address, phone number (if known) and
distance of the help point from your current location.
You have the following options:
►
►
►
Tap on the Map button in order to see your location and the help
point on the map. This gives you an overview of the route to the
help point.
Tap on Start Navigation. You will then be guided directly to the
displayed help point.
You can use the
(Up) and
(Down) buttons to select other
help points in the selected category.
The help points are sorted by distance from your current position.
►
Use the
(Back) button to return to the DIRECT HELP window.
Note: Only those help points are displayed which are situated no further
than than 30 mi from your position.
8.11
GPS Status, saving the current location
In the GPS STATUS window you will find an overview of the data the
navigation system calculates from the GPS signals it receives.
Useful functions
- 83 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
The GPS status can be accessed from the options button in many
windows.
►
Tap on Options > GPS Status.
The current location can be saved in the FAVOURITES list.
1. Tap on Save Position.
The SAVE DESTINATION AS dialog box opens.
2. Enter a name for the destination.
3. Tap on Save.
8.12
Block
You can block a leg of the route at any time during a navigation, i.e. to
re-calculate the route in order to avoid the leg, e.g. if you have heard on
the radio of a traffic jam affecting this section.
Note: The block is valid only for the current navigation. It no longer
exists on a new navigation.
You are currently in a navigation. The map is open in Navigation mode.
1. Tap on Options.
Buttons with various functions will be displayed.
2. Tap on Block.
The BLOCK menu opens. It contains buttons with different distance
values.
3. Select the distance you want to block.
Note: If you are currently driving on a motorway, the alternative route
will begin at the next exit. Indicated on the buttons is the junction up to
which the block extends.
The system recalculates the route. The blocked route section will be
avoided. It is marked on the map in red.
Unblocking a route section
►
Tap on Options > Unblock.
The block will be lifted. The system recalculates the route. The unblocked route section can now be integrated into the calculation.
8.13
Turn-by-Turn List
You can display detailed directions of the calculated route before
starting navigation or at any time during navigation. This list displays all
of the driving instructions in table form.
The map is open in Preview mode:
- 84 -
Useful functions
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
►
Tap on Options > Turn-by-Turn List.
The map is open in Navigation mode or in Reality View mode:
►
Tap on Options > Route > Turn-by-Turn List.
The TURN-BY-TURN LIST window opens.
1
Schematic depiction of the next junction where you must make a turn.
2
Distance to this junction.
3
Route instruction and if available the name of the street into which you
must turn.
4
Indicates whether you want to drive on the route section in question or
not.
(Allow): The section in question is allowed on the route.
(Forbid): The section in question is not allowed on the route.
Blocking route sections
1. Tap on the route sections that you do not want to travel on so that
the
2. Tap on
(Forbid) symbol appears next to them.
(Modify Route).
The navigation system calculates an alternative route avoiding the
route sections selected. The new driving instructions are displayed
in the TURN-BY-TURN LIST window.
3. Tap on
(Back) in order to close the TURN-BY-TURN LIST
window again.
Removing blocks and using original routes
Section blocks can be removed at any time.
Useful functions
- 85 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
►
8.14
In the TURN-BY-TURN LIST window, tap on Options > Calculate
Original Route.
TMC (Traffic Information)
The integrated TMC receiver enables the navigation system to make
use of current traffic messaging. If necessary it can change your route
dynamically, for example in order to avoid a traffic jam.
Note: TMC is available free of charge in many European countries.
PremiumTMC, promising a faster and more up-to-date service, is
offered (exclusively or in addition) in some countries at a charge.
You can subscribe to PremiumTMC services on our website
www.navigon.com.
8.14.1
Preview TMC
If a new traffic message concerning your route arises while navigation is
in progress, the Traffic Information button will appear at the right edge
of the screen.
Recalculate Route: Automatically
If you have selected Automatically for the Recalculate Route setting, the
button will not show a distance. The traffic obstruction will be avoided
automatically.
Recalculate Route: On Request
If you have selected On Request, then the distance to the reported
traffic obstruction will be indicated on the button. The button will turn red
if the distance is less than 50 km.
►
Tap on the
(Traffic Information) button.
The PREVIEW TMC window opens. It shows a map view with the
route section affected by the message. If the reported obstruction is
likely to involve a considerable loss of time, a possible detour will
also be shown.
- 86 -
Useful functions
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Zoom Out: The map section shown becomes larger, but you will see
fewer details.
Zoom In: The map section becomes smaller, but you will see more
details.
Original map section: The original map section is shown again.
►
Tap on the button of the route you want to follow.
-or-
►
Tap on the Details button.
The TRAFFIC INFORMATION window opens. (Refer to "Displaying
traffic information" on page 88.)
) in the map view
Note: If you tap on a traffic symbol (in the display:
of the PREVIEW TMC, a window with detailed information about this
message will open. (Refer to "Showing a single message in detail" on
page 89.)
Recalculate Route: On Request
If you have selected On Request, the button may also appear in green.
In this case there is no longer a traffic obstruction requiring a detour.
►
Tap on the
(Traffic Information) button.
The PREVIEW TMC window opens (see above). You can now have
yourself guided back to the original route or continue on the detour.
Useful functions
- 87 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
8.14.2
Displaying traffic information
Current traffic information is available via the options button in many
windows.
►
In the NAVIGATION window, tap on Options > Traffic.
The TRAFFIC INFORMATION window opens.
You can use the
of messages.
►
1
3
(Down) buttons to scroll in the list
Tap on
(Back) in order to close the TRAFFIC INFORMATION
window again.
The Traffic Information button shows the type of traffic messaging listed
and how many messages of this type are in the list.
►
2
(Up) and
Tap on Traffic Information in order to select the messages you want
displayed.
This mark indicates that the message in question comes from a
PremiumTMC provider.
Here you can see how serious the obstruction is:
Red: The affected section of the route is fully blocked by the obstruction
or involves a considerable loss of time (more than 30 minutes) to pass
through. This can be the case for example when several lanes are
blocked due to an accident.
- 88 -
Useful functions
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Yellow: The section is not fully blocked by the obstruction but there is a
threat of delays (10-30 minutes). This can be the case for example with
slow-moving traffic.
No colour: The obstruction is not classified as serious. This can be the
case for example when slow-moving traffic is reported on a very short
section, when SOS telephones are not working or when parking areas
are blocked off.
4
Here you can see how far you are from this obstruction. If the
obstruction does not lie on your route or if a detour route was already
calculated for this obstruction, then the distance as the crow flies will be
shown.
5
Here the reported obstruction is displayed as a traffic sign.
6
Here the affected road is indicated.
7
Here you can see on which section of the road the obstruction lies.
8
This symbol appears only when the reported obstruction affects your
route. Here you see how the obstruction is treated:
(Detour): An alternative route avoiding the traffic obstruction is
calculated.
(Ignore): This obstruction is ignored.
►
9
8.14.3
Tap on the button to select the alternative setting.
(Show on Map): This button is only available if at least one of the
indicated messages concerns your route. Tap on this button in order to
open the PREVIEW TMC window. (Refer to "Preview TMC" on page 86.)
Showing a single message in detail
►
Tap on a message to display this information in detail.
The navigation system announces the traffic message in question if the
detail view is open. The announcement of traffic messages is not
possible in every language however.
►
8.14.4
Tap on the
(Show on Map) button in order to view the section
concerned on the map.
TMC Settings
►
In the TRAFFIC INFORMATION window tap on Settings.
In the TMC SETTINGS window you can set the TMC traffic station and
configure whether the reception of a traffic message concerning your
route should affect your route planning and if so how.
Useful functions
- 89 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Tuning Mode
Tap on Tuning Mode and select a method for selecting the TMC radio
station.
►
►
►
Automatic: You can use the arrow keys in the station area to select
another station. The system will search for another station if
reception becomes poor.
Hold station: You can use the arrow keys in the station area to
select another station. The system will search for the same station
on a different frequency if the signal becomes poor.
Hold frequency: You can use the arrow keys in the station area to
select another frequency. The system will not search for another
station if reception becomes poor.
Recalculate Route
Tap on Recalculate Route and select how new traffic messages
concerning your route are to be used.
►
►
Automatically: An alternative route will be calculated automatically.
The system will inform you on the recalculation.
On Request: An announcement from the navigation device tells you
that a traffic message concerns your route. On the screen the
Traffic Information box indicates the distance to the reported traffic
obstruction.
Tap on the Traffic Information box. You can then decide whether an
alternative route is to be calculated or not.
8.15
Logbook
You can use your navigation device to record a logbook. The logbook is
recorded in the "Logbook.xls" file. You can open the file with Microsoft
Excel. Each recorded trip is added at the bottom of the table as a new
entry.
The first time a trip is recorded, the "Logbook.xls" file will be created in
the "NAVIGON\Logbook" folder. If you delete or move this file, a new
file will be created when you next record a trip.
Recording trips
You can have all trips recorded automatically.
1. In the NAVIGATION window tap on Options > Settings > Navigation.
2. Set Logbook to Yes.
3. Tap on OK.
Every trip from now on will be recorded until you reset Logbook to No. It
is possible, however, to exclude individual trips from the recording.
- 90 -
Useful functions
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
The navigation system also records trips when you are not navigating.
Of course this requires the navigation system to be switched on and
receiving GPS signals.
Before a trip
If your trips are recorded in the logbook, a window for entering the trip's
key data is opened before the trip begins. You can also decide,
however, not to record the trip in question.
►
If you don't want to record the trip in question, tap on
(Cancel).
-or-
1. In the Reason for the Trip box tap on one of the possible reasons
for the trip.
2. Enter a name for this entry, e.g. "Trip to customer X", in the
Logbook Entry box.
3. Tap on Mileage
4. Enter the mileage of your vehicle.
5. Tap on Start.
Navigation starts.
9
Handsfree Module
This chapter is relevant for you only if your navigation device is one of
the following devices:
►
NAVIGON 40 Premium
►
NAVIGON 40 Premium Live
The navigation device has a hands-free module which supports
Bluetooth connections to Bluetooth-capable mobile phones and
headsets. It can be connected simultaneously to up to two mobile
phones or to a headset.
If you have set up a connection to a mobile phone, you can use the
navigation device as a hands-free module for it.
If you have set up a connection to a Bluetooth headset, you will hear
the voice instructions from the navigation software via the headset. This
is useful for example when travelling on a motorcycle. All other
functions described in this chapter are not available when connected to
a headset.
A compatibility list of all supported mobile phones can be found on our
website www.navigon.com.
Handsfree Module
- 91 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Opening the hands-free module
►
Tap in the navigation application on
(Phone).
The HANDSFREE MODULE window opens.
When you start the hands-free module for the first time, a window will
open in which you can start a search for Bluetooth-capable devices.
►
►
Tap on Yes if you want to start the search now and set up a
connection to a headset or a mobile phone. As soon as the
navigation device has found your Bluetooth device you can initiate
the pairing (refer to "Pairing with a device" on page 94).
Tap on No if you want to initiate the connection later. (Refer to
chapter "Searching for and pairing Bluetooth devices" on page 93.)
Elements of the hands-free module
All functions can be reached from the HANDSFREE MODULE window.
1
Status display of the hands-free module. This status display can also be
seen in the navigation software. (Refer to "Bluetooth / Phone" on
page 23.)
2
The Phone 1 and Phone 2 buttons are used to select the active phone.
(Refer to "Activating a mobile phone" on page 97.)
The button of the currently active phone has a "pressed" look (here:
Phone 2). The name of the active phone appears alongside the buttons.
These buttons can have various colours:
►
►
Green, if a mobile phone is connected as "Phone 1" or as
"Phone 2".
Orange, if no mobile phone is connected.
If the hands-free module is connected to a headset, the
(Headset) button will appear.
3
- 92 -
Speed call buttons (refer to "Preset" on page 104).
Handsfree Module
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
4
Back to the previously opened window. If you press this button, you will
be returned to the navigation application.
5
Opens the TRUSTED DEVICES window. Here you can enter which
devices are connected to the hands-free module. (Refer to "Connecting
to a device" on page 95)
6
Moves the navigation application to the foreground.
The following labelled buttons are also visible:
Keyboard: Opens the keypad on which you can dial phone numbers. (Refer to
"Dialling a telephone number" on page 100.)
Phone Book: Opens the phone book of the active telephone. (Refer to "Calling
a contact from the phone book" on page 101 and "Navigating to a
contact from the phone book" on page 103.)
Recent Calls: Opens the recent calls of the active telephone. (Refer to "Calling
most recently dialled, received or missed numbers" on page 101.)
9.1
Connection with Mobile Phone
To be able to use the hands-free module of the navigation device, it
must be connected to at least one Bluetooth device.
Note: Both the navigation device and the mobile phone must be
configured accordingly in order for a Bluetooth connection to be set up
between the two devices. Headsets are suitably configured at the
factory.
For details of how to configure the navigation device refer to the chapter
"Settings" on page 105.
For details of how to configure the mobile phone or headset refer to the
related manual issued by the manufacturer.
9.1.1
Searching for and pairing Bluetooth devices
Pairing is the term used for setting up a coded connection between two
Bluetooth devices. This requires each of the two devices to send the
same password to respectively the other device. The password and the
connection data are saved on both devices, which means that pairing is
necessary once only when the connection is set up for the first time.
Paired devices are saved in the TRUSTED DEVICES list.
The navigation device can connect automatically to the last connected
device as soon as it is within range.
The hands-free module of the navigation device can save and manage
the connection data of up to 4 paired mobile phones and one headset.
From each paired mobile phone it is possible to import the phone book
and recent calls and to save this information with the connection data.
Handsfree Module
- 93 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Note: In this case the phone book and recent calls are only available
when the phone in question is connected. For details of how to import
the phone book and recent calls refer to the chapters "Import Phone
Book" on page 98 and "Import recent calls" on page 99.
Searching for devices
1. Make sure that the Bluetooth function is activated on both the
mobile phone and the navigation device. If you want to set up a
connection to a headset, the headset must be switched on.
Additional information can be found in the manual issued for the
headset.
2. In the HANDSFREE MODULE window tap on
(Trusted Devices).
The TRUSTED DEVICES window opens.
3. Tap on Options > Search for Devices.
The navigation device starts the search for Bluetooth devices and
lists all the devices it recognises in the DISCOVERED DEVICES
window. The symbol to the left of the device name indicates
whether the device is a mobile phone or a headset.
Pairing with a device
4. Tap in the DISCOVERED DEVICES window on the name of the device
you want to connect to.
►
If pairings already exist with 4 mobile phones or a headset, you will
now be prompted to delete a device from the TRUSTED DEVICES list.
(Refer to "Deleting a device" on page 97.)
5. The navigation device prompts you to enter a password.
►
►
If you are setting up a connection to a mobile phone, enter a
password (1–16 digits) in the Key box and tap on (OK). Then enter
the same password on the mobile phone.
If you are setting up a connection to a headset, enter the headset
password. This password and additional information about pairing
can be found in the manual issued for the headset.
The pairing is performed and a connection is set up between the
two devices. The connected device is indicated in the TRUSTED
DEVICES list. (Green symbol)
9.1.2
Pairing from the mobile phone
Note: Please consult the mobile phone's manual if you are uncertain
about how to carry out the following steps on the mobile phone.
- 94 -
Handsfree Module
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
1. Make sure that the Bluetooth function is activated on both the
mobile phone and the navigation device. To perform the pairing
from the mobile phone, the functions Discoverable by Others and
Others May Connect must also be activated on the navigation
device.
(Refer to "Configuring the hands-free function" on page 104.)
2. Using your mobile phone, search for other Bluetooth devices.
The navigation device is detected as NAVIGON.
3. Initiate a connection to the detected NAVIGON device.
The mobile phone prompts you to enter a password.
4. Enter a password (1-16 digits).
The navigation device prompts you to enter a password.
5. Enter the same password in the Key box as on the mobile phone
and tap on (OK).
The pairing is performed and a connection is set up between the
two devices. The connected device is indicated in the TRUSTED
DEVICES list.
►
►
9.1.3
If the new device is a headset, the symbol will appear to the
right of its name in green colour. The connection to any mobile
phones will be disconnected if applicable.
If the new device is a mobile phone, one of the two symbols will
appear to the right of its name in green colour depending on
whether it is connected as Phone 1 or as Phone 2.
Connecting to a device
In this case "connection" refers to any subsequent connections
between Bluetooth devices which have already been paired. No further
password entry is necessary when connecting.
1. Make sure that Bluetooth is activated on your navigation device.
►
If you want to connect to a mobile phone, make sure that Bluetooth
is activated on the mobile phone and that the Discoverable by
Others and Others May Connect settings are activated.
Note: The exact designation of these settings may vary from
manufacturer to manufacturer. For more details refer to your mobile
phone manual.
►
If you want to connect to a headset, make sure that the headset is
switched on.
Handsfree Module
- 95 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Connecting manually
If a Bluetooth connection to a device is active, you must disconnect this
connection first before you can connect to a different device. The
existing connection is disconnected automatically as soon as the
connection to a different device is initiated.
2. In the HANDSFREE MODULE window tap on
(Trusted Devices).
The TRUSTED DEVICES window opens. Currently connected devices
are marked with a green symbol to the right of their name. Devices
which are not connected have orange symbols.
3. Please ensure that the Bluetooth connection is working properly:
►
►
►
Tap on the
(Connect) symbol in order to initiate a
connection to the corresponding headset. All active connections
to other devices will then be disconnected.
Tap on the
(Connect) symbol in order to connect the
corresponding mobile phone as "Phone 1". The connection to a
headset or to a device which is already connected as "Phone 1"
will be disconnected.
Tap on the
(Connect) symbol in order to connect the
corresponding mobile phone as "Phone 2". The connection to a
headset or to a device which is already connected as "Phone 2"
will be disconnected.
The corresponding symbol will turn green. The navigation device
connects to the selected device.
4. Tap on
window.
(Back) in order to return to the HANDSFREE MODULE
If the telephone to which you want to connect the hands-free module is
not in the list, you can start a search for Bluetooth devices. (Refer to
"Searching for and pairing Bluetooth devices" on page 93.)
Connecting automatically
Note: For automatic connection to be possible, the navigation device
must be saved in the Bluetooth settings on your mobile phone as
"authorised" or "authorised device" (the exact wording can vary from
manufacturer to manufacturer). For details please refer to the manual
issued for your mobile phone.
If the device you want to connect to was either of the two last connected
devices and the Reconnect Automatically setting is activated, the
connection will be set up automatically as soon as the device is within
range.
- 96 -
Handsfree Module
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
9.1.4
Activating a mobile phone
If the hands-free module is connected to two mobile phones, you can
select in the HANDSFREE MODULE window which is to be the active
telephone.
If you want to call someone, the call will be made via the active phone.
Incoming calls and text messages on the inactive telephone will be
announced however and can be taken.
Recent calls and the phone book of the inactive telephone are not
available.
You can activate only one connected telephone.
►
Tap on the
(Phone 1) or
the corresponding mobile phone.
(Phone 2) button to activate
The button of the active phone has a "pressed" look. The name of
the active phone is shown to the right of the buttons.
If no mobile phone is connected yet as "Phone 1" or as "Phone 2", the
symbol on the corresponding button will appear in orange. If you tap on
the symbol, the TRUSTED DEVICES window will open. There you can
connect a mobile phone to the hands-free module. (Refer to
"Connecting to a device" on page 95.)
9.1.5
Deleting a device
You can delete the connection data of paired devices. The device is
then no longer shown in the TRUSTED DEVICES list. If you imported the
phone book or recent calls from this device, these data will be deleted
from the navigation device.
1. In the HANDSFREE MODULE window tap on
(Trusted Devices).
The TRUSTED DEVICES window opens.
2. Tap on Options > Delete Device.
The DELETE DEVICE window opens.
3. Tap on the
(Delete Device) button to the right of the device you
want to delete.
You will be requested to confirm deletion.
4. Tap on Delete.
The device is deleted from the TRUSTED DEVICES list.
Handsfree Module
- 97 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
9.1.6
Import Phone Book
For each paired mobile phone in the TRUSTED DEVICES list it is also
possible to import its phone book and save it together with the
connection data. Access to the phone book of a mobile phone is then
only possible when the navigation device is connected to the mobile
phone from which the phone book was imported. As soon as you
connect to a different phone or disconnect the connection, the phone
book will no longer be available on the hands-free module.
1. In the HANDSFREE MODULE window activate the mobile phone
whose phone book you want to import. (Refer to "Activating a
mobile phone" on page 97.)
2. Tap in the HANDSFREE MODULE window on the Phone Book button.
The phone book import is started. Depending on the size of the
phone book this can take some time. When the import is completed,
the phone book is opened.
Note: The number of phone book entries that can be imported from the
mobile phone is limited to 1000.
Note: It can take some time to import a phone book depending on its
size. During the import you can move the Bluetooth application into the
background in order e.g. to show the map during navigation. Tap in the
window opened during the import on the To background button in order
to move the navigation application into the foreground.
Editing and updating a phone book
The phone book cannot be edited in the hands-free module. If you want
to change or delete an entry in the phone book, you must make the
changes on your mobile phone and then update the phone book on the
hands-free module. The phone book is re-imported for the update.
1. In the HANDSFREE MODULE window activate the mobile phone
whose phone book you want to update. (Refer to "Activating a
mobile phone" on page 97.)
2. Tap in the HANDSFREE MODULE window on the Phone Book button.
The phone book of the active phone is opened.
3. Tap on Options > Refresh.
The phone book import is started.
Note: Deleting the complete phone book is possible only by deleting the
mobile phone from the TRUSTED DEVICES list (refer to "Deleting a
device" on page 97). In this case the connection data, phone book and
recent calls will all be deleted, which means that you will have to repeat
the pairing routine in order to set up a connection with the device again.
- 98 -
Handsfree Module
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
For more details about the phone book refer to the chapter "Calling a
contact from the phone book" on page 101.
9.1.7
Import recent calls
For each paired mobile phone in the TRUSTED DEVICES list it is also
possible to import its recent calls and save them together with the
connection data. Access to the recent calls of a mobile phone is then
only possible when the navigation device is connected to the mobile
phone from which the phone book was imported. As soon as you
connect to a different phone or disconnect the connection, the recent
calls will no longer be available on the hands-free module.
Note: The number of recent calls that can be imported from the mobile
phone is limited to 20.
1. In the HANDSFREE MODULE window activate the mobile phone
whose recent calls you want to import. (Refer to "Activating a
mobile phone" on page 97.)
2. Tap in the HANDSFREE MODULE window on the Recent Calls button.
The recent calls import is started. When the import is completed,
the recent calls are shown.
9.2
Taking a call
When you receive a call, a ring tone will sound and the INCOMING CALL
window will open. The header line shows which connected phone is
receiving the call.
The name and the number of the caller will be displayed if this
information is available. (If the caller's number is displayed but does not
exist in the phone book, Unknown caller will be displayed instead of
the name. If the number is suppressed, Phone number hidden will be
displayed.)
►
Tap on Accept if you want to take the call.
The CALL IN PROGRESS window opens.
►
Tap on Reject if you do not want to take the call.
Note: Navigation instructions are muted during a call.
9.3
Receiving a text message
The hands-free module can show incoming text messages (SMS).
Handsfree Module
- 99 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
When you receive a text message, a signal tone will sound and the
INCOMING TEXT MESSAGE window will open. The header line shows
which connected telephone received the text message.
The name and the number of the sender will be displayed if this
information is available. (If the sender's number is displayed but does
not exist in the phone book, Unknown caller will be displayed instead
of the name. If the number is suppressed, Phone number hidden will
be displayed.)
►
Tap on Read if you want to read the text message now.
The TEXT MESSAGE window opens. You can then read the text
message.
Note: The navigation system will also read out the text to you when the
window is opened. Reading out text messages is not possible in all
languages however.
►
Tap on Cancel if you want to read the message later.
Note: You can also choose not to have incoming text messages
announced immediately. (Refer to "Settings" on page 105.)
You can however open the list of received text messages at any time to
check whether you have received any new text messages. (Refer to
"Opening the mailbox" on page 103.)
9.4
Making a call
With the hands-free module you can make a call in various ways.
9.4.1
Dialling a telephone number
1. In the HANDSFREE MODULE window activate the mobile phone which
you want to use to make the call. (Refer to "Activating a mobile
phone" on page 97.)
2. Tap in the HANDSFREE MODULE window on the Keyboard button.
The TELEPHONE NUMBER window opens.
3. Enter the desired telephone number.
4. Tap on the Call button.
9.4.2
Dialling a Speed Call number
A total of 4 speed call buttons are available. These buttons can be
configured separately for each paired mobile phone.
1. In the HANDSFREE MODULE window activate the mobile phone which
you want to use to make the call. (Refer to "Activating a mobile
phone" on page 97.)
- 100 -
Handsfree Module
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
2. Tap in the HANDSFREE MODULE window on the corresponding
Speed Call button.
Note: If the selected speed call button has not been configured yet, it
will be labelled with just three dots (…). If you tap on the symbol, the
MODIFY PRESET window will open. (Refer to "Preset" on page 104.)
9.4.3
Calling a contact from the phone book
You can select numbers from the phone book of the active telephone.
1. In the HANDSFREE MODULE window activate the mobile phone which
you want to use to make the call. (Refer to "Activating a mobile
phone" on page 97.)
2. In the HANDSFREE MODULE window tap on Phone Book.
►
If the phone book of the active phone was not yet imported, the
import will be started now. (Refer to "Import Phone Book" on
page 98.)
3. Select from the phone book the contact you want to call.
The SELECTED PHONE BOOK ENTRY window opens. It shows all the
phone numbers and addresses which have been saved for the
selected contact.
4. Tap on the
to dial.
9.4.4
(Call) button alongside the phone number you want
Calling most recently dialled, received or missed numbers
The RECENT CALLS list contains outgoing, received and unanswered
calls on the active telephone.
Note: Incoming and unanswered calls can be dialled only if the caller's
number was transmitted.
1. In the HANDSFREE MODULE window tap on Recent Calls.
►
If the recent calls on the active phone were not yet imported,
the import will be started now; refer to "Import recent calls" on
page 99.
The RECENT CALLS list opens. The entries are sorted
chronologically; the symbols to the right of the entry indicate the
type of call:
(Missed calls) (orange)
(Incoming calls) (white)
(Outgoing calls)
Handsfree Module
- 101 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
2. Tap on the entry you want.
Note: The RECENT CALLS list is available to the hands-free module only
for as long as the hands-free module is connected to the mobile phone.
It is updated automatically each time it is opened.
9.4.5
Transferring a call from your mobile telephone
The navigation device takes calls automatically from the mobile phone
as soon as a Bluetooth connection is established between the two
devices.
9.5
During a call
You are calling using the hands-free module. The CALL IN PROGRESS
window is open.
9.5.1
Moving the navigation application to the foreground
You can move the navigation application to the foreground at any time.
In this way you can have the map with the navigation instructions in the
foreground during a call when the navigation device is in the process of
navigating.
►
Tap on
(Navigation).
While a call is in progress, the
(Call in Progress) symbol is visible
in the top right corner of the display. The number indicates which of the
connected phones is being used to make the call (here: "Phone 1").
►
9.5.2
Tap on
window.
(Phone) in order to open the CALL IN PROGRESS
Entering numbers
You can enter numbers during a call. This may be the case, for
example, if a further connection via a telephone system is necessary.
1. Tap on Keyboard.
2. Enter the desired numbers.
3. Tap on
window.
9.5.3
(Back) in order to open the CALL IN PROGRESS
Muting the microphone
During the call, you can mute the microphone so that you can talk to
someone without the interlocutor hearing.
►
- 102 -
In the CALL IN PROGRESS window, tap on
switch off the microphone.
(Muting) to
Handsfree Module
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
The person on the other end of the line can no longer hear you. The
modified symbol on the button indicates this.
►
9.5.4
Tap on
(Muting) to switch the microphone on again.
Transferring a call to the mobile phone
►
In the CALL IN PROGRESS window, tap on Options > Use Mobile
Phone.
You can now continue the call from your mobile phone.
9.5.5
Ending the call
►
Tap in the CALL IN PROGRESS window on the Hang up button in
order to end the call.
9.6
Useful functions
9.6.1
Navigating to a contact from the phone book
You can also use the address of a contact in the phone book of the
active telephone as a destination for the navigation system.
1. In the HANDSFREE MODULE window tap on Phone Book.
2. Select from the phone book the contact you want to navigate to.
The SELECTED PHONE BOOK ENTRY window opens. It shows up to
two addresses and up to four phone numbers which have been
saved for the selected contact.
3. Tap on Start Navigation.
If more than one address is available for the selected contact, all
the addresses will be shown.
►
Tap on the address to which you want to navigate.
You can also select addresses from the phone book in the navigation
software to act as destinations. For more details refer to the chapter
"Imported Addresses from the phone book" on page 38.
9.6.2
Opening the mailbox
You can read text messages from the mailbox of the active telephone.
Note: The number of SMS that can be imported from the mobile phone
is limited to 15.
1. In the HANDSFREE MODULE window, tap on Options > SMS inbox.
Handsfree Module
- 103 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
The SMS INBOX list opens. The entries are sorted in chronological
order. The symbol to the right of each entry indicates whether the
text message has been opened at least once:
(Unopened text message)
(Opened text message)
2. Tap on the entry you want.
Note: The SMS INBOX list is available to the hands-free module only for
as long as the hands-free module is connected to the mobile phone. It
is updated automatically each time it is opened.
9.7
Configuring the hands-free function
The hands-free module contains a number of settings that can be
individually configured.
9.7.1
Preset
The hands-free module of the navigation device contains four Speed
Call buttons that can be individually configured.
1. In the HANDSFREE MODULE window, tap on Options > Modify Preset.
The PRESET window opens.
2. Tap on the
to define.
(Edit) button to the right of the Speed Call you want
The MODIFY PRESET window opens.
Entering a new Speed Call number or editing an existing Speed Call
number
3. Tap on the
(Edit) button.
4. Enter the name and the number for the selected Speed Call button
or edit the existing name and number.
5. Tap on OK.
Adopting a number from the phone book of the mobile phone
3. Tap on the
(From the phone book) button. This button is
deactivated when there is no connection to a mobile phone.
4. Select the contact which you want to adopt for the Speed Call.
The SELECT PHONE NUMBER window opens. It shows all the phone
numbers saved for the selected contact.
5. Tap on the phone number you want to use for the Speed Call.
- 104 -
Handsfree Module
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Deleting a Speed Call number
3. Tap on the
(Delete) button.
4. Confirm that you want to delete the Speed Call number.
The PRESET window opens again. No phone numbers and no name
exist any longer for the selected Speed Call button.
9.7.2
Settings
In the SETTINGS window you can configure the settings for the phone
functions of the hands-free module.
►
In the HANDSFREE MODULE window, tap on Options > Settings.
The SETTINGS window opens.
Volume of the Phone Call: The volume of the phone call can be controlled
independently of the volume of the navigation application.
Volume of the Ring Tone: The volume of the ring tone can be controlled
independently of the volume of the navigation application.
Info about new text messages: Select whether you want incoming text
messages to be announced (Yes or No).
Bluetooth Function: Select whether you want to activate the Bluetooth function
(Yes or No).
The hands-free module cannot connect to a mobile phone or headset if
the Bluetooth function is deactivated.
Others May Connect: Select whether other devices should be able to initiate a
connection (Yes or No).
Discoverable by Others: Select whether other Bluetooth-capable devices (in
particular mobile phones) should be able to detect the navigation device
(Yes or No).
Reconnect Automatically: Select whether the connection to the last connected
phone is to be restored automatically (Yes or No) as soon it comes
within range again.
Sort phone book by: Select the column to be used for sorting the phone book
(First Names or Last Names). This setting applies only to the phone
book display in the navigation device.
For information about configuring the settings in this window refer to
"Configuring the navigation system" on page 112.
Note: In order for the last connection to be restored without further
questioning, the navigation device must be saved in your mobile phone
as "authorised" or "authorised device" (the exact wording can vary from
manufacturer to manufacturer).
Handsfree Module
- 105 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Note: The Discoverable by Others and Others May Connect settings
are effective only when the Bluetooth function is activated.
A Bluetooth connection can be initiated from the mobile phone only
when Yes is selected for both settings.
10
Navigon Live
10.1
Before you begin
With the NAVIGON Live module you can access up-to-date online
services of NAVIGON Live Services at any time:
►
►
Weather Live: You are informed about the current weather
situation for every point of the road network on the navigation maps
available. A weather forecast for the next few days is also provided.
CleverParking Live: If for example you want to navigate to a car
park, you can find out before starting the navigation whether there
are any free parking spaces still there. You are also provided with a
forecast as to whether the car park is likely to get fuller or emptier at
the present time.
The information you receive depends on the information which the
car park operator makes available.
►
►
Google Local Search: If you are searching for a particular category
of destination, e.g. a Thai restaurant, you can use Google Local
Search. You then have access to the recommendations and ratings
of millions of people world-wide.
Traffic Live: You can now receive traffic information from the
NAVIGON Live server. This server evaluates not only information
from radio stations but also floating car data from the numerous
users of NAVIGON Live services. As the result, traffic jams can be
detected and avoided more quickly and more reliably. The
evaluation of floating car data also helps to calculate the estimated
time of arrival more exactly.
The data connection between the NAVIGON Live module and the
NAVIGON Live services is set up by mobile radio. The necessary SIM
card is already inserted in the module. It can be used only for the
NAVIGON Live services and is blocked for all other services
(telephone, SMS, MMS etc.).
10.1.1
Costs
Use of the NAVIGON Live services is free for a certain period from the
day of initial activation. No mobile radio charges or data traffic charges
are incurred. After this period you can continue to use the services by
extending the subscription. For details go to our website
www.navigon.com/live.
- 106 -
Navigon Live
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
No additional charges arise for using the NAVIGON Live services in
European countries other than your home country. Please note
however that e.g. information about parking space, prices and
availability does not exist in every country on a nation-wide basis.
For more details about the availability and scope of the NAVIGON Live
services in various countries and about subscriptions go to
www.navigon.com/live.
10.2
Using the NAVIGON Live services
The NAVIGON Live services are seamlessly integrated in the
navigation software. Many services are used automatically without any
change to the operation of the navigation device compared to the
version without NAVIGON Live services. For example, there is no
change to the program flow when a traffic jam is reported. The only
change is that the traffic information from the NAVIGON Live services
is more up to date and more precise than the traffic information from the
radio stations.
10.2.1
Weather Service
The Weather Live service provides up-to-date weather data for every
point of the road network on the navigation maps available. A weather
forecast for the next few days is also available.
Weather data for your current position
This function is interesting above all when you want a weather forecast
for the next few days.
►
in the NAVIGATION window tap on
Service.
(NAVIGON Live) > Weather
The WEATHER SERVICE window opens. You are shown a map view
containing your position. Alongside are the current weather data
and a forecast for the next two days.
Weather data for your destination
You can call up weather data for your destination at any time during
navigation.
►
Tap on Options > Services > Weather Service.
The WEATHER SERVICE window opens. You are shown a map view
containing the destination selected for the navigation. Alongside are
the current weather data and a forecast for the next two days.
Navigon Live
- 107 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Note: If you have planned a multi-leg route, the weather data for the
ultimate destination will be shown and not the data for the next
intermediate destination.
Weather data for a different location
You can call up weather data for every point on the map which can be
entered as a destination for the navigation system.
Except for Take Me Home and Show Map > Destination search you can
use any possible type of entry, e.g. Enter an Address, Favourites or
Search for POI.
If you enter an address, it suffices to enter the town. However, you may
also enter the street and the house number.
Information about entering navigation destinations can be found in the
manual issued for your navigation device.
1. Enter the town for which you want to receive weather data in the
same way as you enter destinations for the navigation system. Do
not tap on Start Navigation!
►
If navigation is in progress, then tap on Options > Destination > Add
interim destination and then enter the town for which you want
receive weather data. Do not tap on Start Navigation!
2. Tap on Options > Weather Service.
The WEATHER SERVICE window opens. You are shown a map view
containing the town you entered. Alongside are the current weather
data and a forecast for the next two days.
10.2.2
Parking
The CleverParking Live service provides details about numerous
parking options. These details cover e.g. prices, opening times, number
of free parking spaces, trends in available capacity, availability of
parking spaces for women, availability of parking spaces for the
handicapped, type of payment, type of monitoring, …
Note: The CleverParking Live service can only provide the information
which is made available by the car park operator. This is not always the
case where information about available capacity and prices is
concerned.
1. In the NAVIGATION window tap on
(NAVIGON Live) > Parking if
you are looking for a car park near your current position.
-or►
- 108 -
Use one of the methods described in the manual issued for
navigation device to search for a car park near your destination.
Navigon Live
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
A list opens. You are shown possible car parks in order of distance
from your destination.
For some of the parking options you are shown online information
such as e.g. the number of currently free parking spaces, the
currently valid price or the trend in available capacity.
Some parking options are marked by a small asterisk (e.g.
).
There is more information available for these parking options, e.g.
opening times or the number of parking spaces for women or the
number of parking spaces for the handicapped.
2. Select a parking option.
The DESTINATION INFO window opens. It contains address data and
any other information which may be available.
10.2.3
Google Local Search
When you search for POIs, the Google Local Search service provides
you with the same results as when searching with Google Maps.
For many POIs in the hit list there are assessments which were written
by Google Maps users and rankings which range from 1 star to 5 stars.
The average ranking is always shown. No star means that no rating
was given yet.
Note: Google allows the use of the Google Local Search service only
if you observe its conditions of use which can be viewed at
www.google.com/accounts/TOS.
1. in the NAVIGATION window tap on
Local Search.
(NAVIGON Live) > Google
-orIn the NAVIGATION window tap on New Destination > Search for
POI > Google Local Search.
The GOOGLE LOCAL SEARCH window opens.
2. Enter the name of the destination town.
You don't need to enter anything if you are looking for a POI near
your current position.
If the destination is abroad you can also enter the name of the
country, e.g. "Paris France".
Please note that every entry is possible. If you make a mistake, you
might not receive the results you expected.
►
Tap on
(Open List) in order to be able to select from the
last 30 town entries.
3. Tap on
Navigon Live
(OK).
- 109 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
4. Enter a search term.
You have an absolutely free choice of search term, but the number
of hits depends greatly on you entering a suitable search term.
►
Tap on
(Open List) in order to be able to select from the
last 30 entered search terms.
5. Tap on
(OK).
The RESULTS list opens. It contains the POIs which were found.
Shown alongside each POI is the average rating (1 star to 5 stars).
No star means that no rating was given yet.
6. Tap on the name of the destination to which you want to navigate.
The DESTINATION INFO window opens. It contains the average
rating, the telephone number and the address data for the selected
destination.
►
►
►
Tap on
(Info) if you want to read the assessments for this
destination.
Tap on
the map.
(Show on Map) in order to see the destination on
Tap on
(Call) in order to dial the number indicated.
Note: The Call function is only available when the navigation device is
connected via Bluetooth to a mobile phone.
Whether and how a Bluetooth connection can be established is
described in the manual issued for the navigation device.
7. Tap on Start Navigation.
-orTap on Parking in order to search for and navigate to a car park
near your destination.
The map opens in Preview mode. The destination is indicated on
the map.
For detailed information on how to start navigation, please refer to
chapter "Route preview" on page 40. Please read on there.
- 110 -
Navigon Live
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
10.2.4
Traffic Information
The Traffic Live service evaluates not only the information which is
made available to it by radio stations but also floating car data from the
numerous users of the service. This offers for example the following
advantages:
►
►
►
Obstructions which cause traffic congestion can be detected and
avoided more quickly and more reliably.
The end of a traffic obstruction is detected more quickly and more
reliably. Unnecessary detours can be avoided.
Estimated times of arrival can be calculated more precisely.
The Traffic Live service does not change the way you operate the
navigation device; the only difference is the source of reference for the
traffic information.
For details of the TMC function refer to chapter "TMC (Traffic
Information)" on page 86.
10.3
Configuring the NAVIGON Live services
In the SETTINGS window you can configure the settings for the
NAVIGON Live services.
►
In the NAVIGATION window tap on
Settings.
(NAVIGON Live) > Options >
The SETTINGS window opens.
Use NAVIGON Live Services: Select whether you want the NAVIGON Live
services to be available (Yes or No).
Source of traffic information: Select the traffic information source you want to
use (NAVIGON Live services or radio stations). The NAVIGON Live
services -also include floating car data from numerous vehicles in its
analysis of the traffic situation. As the result they often provide more
information and sooner.
Optimise Traffic Recognition: The navigation device sends anonymised floating
car data to the NAVIGON Live server. The more users that provide
floating car data anonymously, the better the system can identify traffic
jams and the more reliably it can avoid them. Estimated times of arrival
can also be calculated more precisely. Select whether you want to send
floating car data (Yes or No). Floating car data cannot be traced back in
any way to you personally.
Details of how to operate the SETTINGS window can be found in the
manual issued for your navigation device.
Navigon Live
- 111 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
10.4
Indicating the status
All key data concerning your NAVIGON Live module and the validity of
the subscription to the NAVIGON Live services can be found in the
NAVIGON LIVE STATUS window.
►
In the NAVIGATION window tap on
NAVIGON Live Status.
(NAVIGON Live) > Options >
The NAVIGON LIVE STATUS window opens. It contains the following
information:
►
11
The date up to which the subscription to the NAVIGON Live
services is valid or since which the subscription has expired,
►
The number of the SIM card in the NAVIGON Live module,
►
the activation code last entered on the navigation device.
Configuring the navigation system
The SETTINGS window is the starting point for customising the
navigation system to match your personal preferences.
Settings can be accessed via the options in the NAVIGATION window
and via the options in many windows of the navigation application.
►
Tap on Options > Settings.
The SETTINGS window of the navigation application has several buttons:
Navigation, Current Route Profile:, Map Display and General.
►
Tap on a button to open the corresponding settings window.
The settings of the individual windows are distributed over several
screen pages. You can use the
(To the Left) and
these pages.
(To the Right) buttons to toggle between
Some settings can have only one of two values. These settings can be
recognised by the
(Toggle) button. All possible values are visible.
The currently valid value is highlighted (in white).
►
- 112 -
Tap on
(Toggle) in order to switch between the possible values.
Configuring the navigation system
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Some settings can adopt many different values. These settings can be
recognised by the
1. Tap on
(List) button. The current value is visible.
(List).
A list with all possible values opens. The currently valid value is
marked.
2. Tap on the value you want. It is now marked.
3. Tap on OK.
The list will close. The new value is indicated.
For each setting there is a
(Help) button. When you tap on it you
will see an exact definition of the setting in question.
You can close the settings windows in two ways:
►
Tap on OK.
►
Tap on Cancel.
Any changes you have made will be adopted.
Any changes you have made will not be adopted.
Configuring the navigation system
- 113 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
12
Appendix
12.1
Technical data of the navigation device
Dimensions
Weight
Operating
conditions
120.5 x 75 x 15.2 mm
approx. 145 g
Operating
temperature
Storage
temperature
Humidity
CPU
Operating system
Display
RAM
Memory
Flash
GPS
TMC
Device keys
I/O
Keyboard
Loudspeaker
Memory card
USB
Bluetooth
Power supply
Rechargeable
battery
- 114 -
-10°C to 70°C (14°F to 158°F)
-30°C to 80°C (-22°F to 176°F)
0% to 90%, non-precipitating
SiRF ATLAS 5
Microsoft Windows CE
4.3" LCD colour display with resistive
touch-panel, 350 cd/m², 300:1
480 x 272 pixel (WQVGA)
NAVIGON 40 Essential: 64 MB
NAVIGON 40 Easy: 64 MB
NAVIGON 40 Plus: 64 MB
NAVIGON 40 Premium: 128 MB
NAVIGON 40 Premium Live: 128 MB
NAVIGON 40 Essential: 2 GB
NAVIGON 40 Easy: 2 GB
NAVIGON 40 Plus: 4 GB
NAVIGON 40 Premium: 4 GB
NAVIGON 40 Premium Live: 4 GB
yes
Built-in antenna
yes
1 (On/Off)
Software keyboard
yes
microSD
1 x USB 2.0
(Only NAVIGON 40 Premium and
NAVIGON 40 Premium Live)
Integrated
With echo suppression
Via USB socket
Type
LiIon, 1300 mAh
Charging
Electronic
Integrated
Car charger
cable
Input
Output
10-24V = (direct voltage, DC)
5V = (direct voltage, DC)
Appendix
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
12.2
Technical data of the NAVIGON Live-module
This chapter is relevant for you only if your navigation device is a
NAVIGON 40 Premium Live.
Dimensions
Weight
Operating
conditions
Power supply
Car charger
cable
Appendix
82,5 x 36.9 x 18.2 mm
approx. 76 g
Operating
temperature
Storage
temperature
Humidity
Input
Output
-10°C to 55°C (14°F to 131°F)
-30°C to 65°C (-22°F to 149°F)
0% to 90%, non-precipitating
via USB socket
10-24V = (direct voltage, DC)
5V / 1.5A = (direct voltage, DC)
- 115 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
12.3
§1
NAVIGON Licensing Policy
Scope of Regulations
This Agreement regulates the relations between the user and
NAVIGON AG, Schottmuellerstrasse 20 A, 20251 Hamburg, developer
and proprietor of the exclusive utilisation rights to the NAVIGON
software (“Software”) as specified in the order. The subject matter of
this Agreement is copyright interests.
§2
Extent of Use
(1)
NAVIGON grants the user the non-exclusive right, unlimited by time and
location, to utilise the Software at a utilisation volume as specified in the
order. The licensing includes the right to install and use the Software in
accordance with the documentation and pursuant to these regulations.
(2)
NAVIGON expressly informs the user that complete utilisation of the
Software is not possible until after proper registration.
(3)
The user must ensure that the above mentioned restricted utilisation
rights are complied with.
(4)
Any kind of use which goes beyond the framework as stipulated in the
Agreement requires the written consent of NAVIGON. In the event that
such utilisation should be exploited without NAVIGON’s consent,
NAVIGON shall charge the amount accruing for this extended utilisation
in accordance with the valid price list at the time. NAVIGON shall
reserve the right to assert further reaching claims for compensation of
damages. The user shall have the right to prove lower damages.
(5)
All the above mentioned utilisation rights shall only be transferred to the
user after full and final payment of the license fee.
§3
(1)
- 116 -
Copyright and Protection Rights
The user acknowledges the copyrights of NAVIGON and therewith its
exclusive utilisation and exploitation rights to the Software. Exclusive
utilisation and exploitation rights also exist with regard to extended
development of the Software or amendments thereto, which NAVIGON
has created for the user compliant with the order.
Appendix
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
(2)
Any kind of non explicitly authorised copying of the Software in its
entirety or partially, any kind of non expressly authorised passing on of
the Software and development of similar Software or segments of such
Software or utilisation of the contractual Software as a master template
shall in particular be deemed to be judicially and contractually
prohibited.
(3)
The user acknowledges the imprint, trademark, trade name and patent
rights of NAVIGON to the Software and the relevant appending
documentation. The user is forbidden to remove, change or in any other
way camouflage the copyright notices and identifications pertaining to
existing protection rights.
§4
Passing on the Software
(1)
The user is permitted to sell or give away the Software and the user
manual or any other accompanying materials on a permanent basis to
third parties, under the proviso that the acquiring third party agrees that
the contractual terms and conditions at hand shall henceforth also be
imposed on it.
(2)
In the event of passing on the Software, the user shall hand over to the
new user all copies of the program, including possible back-up copies
made, or destroy the copies not handed over. As a result of passing on
the Software, the former user’s utilisation rights to the program shall
extinguish.
(3)
The user is permitted to sell or give away the Software and the user
manual or any other accompanying materials to third parties on a
temporary basis, if this is not done within the framework of leasing or
renting out for gainful purposes, under the proviso that the acquiring
third party agrees that the contractual terms and conditions at hand
shall henceforth also be imposed on it. For the period of assignment of
the Software to third parties, the assigning user shall have no right to
any kind of utilization of the program. For the period of assignment of
the Software to third parties, the assigning user shall have no right to
any kind of utilisation of the program. Renting out or granting a lease for
gainful purposes shall be prohibited.
(4)
The user may not assign the Software to third parties if there should be
any justified suspicion that such third party could violate the contractual
terms and conditions, especially by making unlawful copies.
Appendix
- 117 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
§5
Reproduction Rights and Access Security
(1)
The user may reproduce the Software if the respective copying should
be necessary for operation. Necessary reproduction shall be deemed to
be the installation of the program from the original data carrier to the
bulk memory of the hardware used as well as loading of the program
into random access memory.
(2)
Furthermore, the user is permitted to make copies for back-up
purposes. However, fundamentally, only one single back-up copy may
be made for safekeeping. The back-up copy has to be identified as
such.
(3)
If regular copying of the complete database, including computer
programs, is indispensable for reasons of data security or to ensure
speedy reactivation of the computer system after a total crash, then the
user is allowed to make back-up copies in the number specifically
required. The data carriers used in this case must be marked
accordingly. The back-up copies may only be used for purely archiverelated purposes.
(4)
Further reproductions, which also include release of the program code
on a printer as well as photocopying of the manual, may not be made
by the user. Any additional manuals required by employees have to be
obtained from NAVIGON.
§6
Multiple Deployment and Network Integration
(1)
The user may use the Software on any hardware available to it.
However, in the event that the user should replace the hardware, it is
obliged to delete the Software from the hardware utilised up till then.
Any isochronous storage, keeping in stock or operation on more than
only one hardware unit is not permissible.
(2)
The deployment of the entrusted Software within a network or any other
multiple workstation computer system is not permissible if thereby the
possibility of simultaneous multiple usage should be facilitated. Should
the user select to use the Software within network operations or any
other multiple workstation computer system, the user is obliged to
abstain from simultaneous multiple use by integration of access
protection devices or to compensate NAVIGON by payment of special
network license fees to an amount calculated on the basis of the
number of users linked up with the computer system. The user shall be
informed immediately by NAVIGON with regard to network license fees
to be raised in each individual case as soon as the user has informed
NAVIGON in writing of the intended network integration and the number
of integrated users. The implementation into such kind of network or
multiple workstation computer system shall only be permissible after full
and final payment of the network licensing fees.
- 118 -
Appendix
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
§7
Third Party Software
The Software contains third party software products which have been
integrated into the contractual Software or supplied together with the
contractual Software. NAVIGON fundamentally only awards such rights
which are necessary for general use of the programs as components of
the contractual Software and which NAVIGON is authorised to grant.
No modification rights or further processing rights are incorporated
therein.
§8
Decompiling and Amendment of Programs
The user is forbidden to retranslate the entrusted program code into
other code configurations (decompiling) as well as any other kind of
inverted development of the diverse manufacturing phases of the
Software (reverse engineering) or to carry out program amendments of
any kind unless such actions should serve purposes of eliminating
serious defects, especially such defects which can not be avoided by
organisational or any other reasonable measure of remedy. Copyright
markings, serial numbers as well as other characteristics serving
purposes of identification of the program may not be eliminated or
changed. Any removal of copy protection or similar protective routine
measures is prohibited without the knowledge and co-operation of
NAVIGON.
§9
Final Clauses
(1)
In the event that any provision contained in this License Policy should
be determined to be invalid or become invalid, the effectiveness of the
other regulations shall not be affected thereby. The said invalid
provision shall be replaced by a valid provision within the context of the
remaining contractual interpretation, which comes as close as possible
to the intended economical purpose of such invalid provision.
(2)
Amendments and supplements to these regulations have to be in the
written form and have to be expressly identified as such. Verbal
ancillary agreements shall be deemed to be ineffective. This
requirement of written form may only be renounced by written
agreement.
(3)
If legally permissible, the Parties agree that the laws of the Federal
Republic of Germany shall apply to all legal relations arising from these
contractual relations, under exclusion of UN Purchase Law.
Appendix
- 119 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
(4)
If the user should be a businessman within the meaning of the
Commercial Code, legal entity under public law or special assets under
public law, all disputes which may arise in connection with the
accomplishment of these contractual regulations shall fall under the
jurisdiction of Hamburg.
12.4
Declaration of Conformity
NAVIGON AG declares herewith that the devices described in the
manual are in conformance with the basic requirements and other
relevant provisions of EU Directive 1999/5/EC and the R&TTE
Directive.
The declaration of conformity can be viewed on the Internet at
www.navigon.com/ce-erklaerung.
13
Troubleshooting
In this chapter you will find solutions to problems which may arise
during use of the navigation system.
This list does not claim to be complete. Answers to many other
questions can be found on the NAVIGON website. (Refer to "Questions
about the product" on page 9.)
I have connected a charger to the navigation device. A connection to a
computer is shown on the screen.
-orI have connected the navigation device to a computer but it is not
detected as a removable disc.
The USB connector of the charger is not fully inserted in the case.
-orThe USB connector is not connected correctly.
1. Unplug the connector.
The navigation device will carry out a new start. Wait for the
navigation software to be reloaded.
2. Insert the USB connector from the charger into the corresponding
socket of the navigation device swiftly as far as it will go. (Refer to
"Description of the navigation device" on page 10.)
My navigation device makes no response any longer, the screen is frozen.
Perform a reset.
►
Use a thin object to press the Reset key. (Refer to "Description of
the navigation device" on page 10.)
The software will be restarted. Your settings and your saved
destinations and routes will be retained.
- 120 -
Troubleshooting
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
It seems to me that the battery of my navigation device becomes flat
relatively quickly when the device is not connected to an external power
supply.
Some settings can be configured so that energy consumption is
minimised.
1. In the NAVIGATION window tap on Options > Settings > General.
2. Set the values for Brightness Day and Brightness Night as low as
possible.
3. Tap on OK.
4. Tap on
(Back).
The NAVIGATION window is now open again.
I have accidentally activated demo mode.
If you have accidentally activated demo mode when you start the
navigation application for the first time, you can deactivate it again as
follows:
1. In the NAVIGATION window, tap on Options > Settings.
The SETTINGS window is opened.
2. Tap on Options > Stop Demo Mode.
You will be prompted to confirm that you want the device reset to
the as-delivered state.
3. Tap on the Yes button.
The software is re-started and behaves as if started for the first time
after being purchased (refer to "Switching on the navigation device"
on page 18).
Start the navigation software and set the Start in Demo Mode
setting to No. (Refer to "Starting the navigation application" on
page 27.)
Note: Use only accessories that are recommended by NAVIGON
expressly for your navigation system. NAVIGON AG accepts no liability
for errors or damages resulting from the use of other accessories.
For suitable accessories go to www.navigon.com or your authorised
dealer.
Troubleshooting
- 121 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
14
Index
1
D
1-Click-Menu ..................................... 52
Data entry.......................................... 24
Description .......................................... 9
Destination
Direct Access................................ 34
Enter Coordinates......................... 29
Favourites ..................................... 35
From Map ..................................... 38
From the phone book ................. 102
Google Local Search .................. 108
Home Address ........................ 38, 41
Imported Addresses
From the phone book ....... 37, 102
Outlook / Internet...................... 36
Last Destinations .......................... 36
My Destinations ............................ 27
New Destination ........................... 27
POI ............................................... 31
Direct Access ........................... 34
in a City .................................... 33
Nationwide ............................... 32
Nearby...................................... 31
Save ............................................. 41
Start Navigation ............................ 39
Take Me Home ....................... 38, 41
Turn-by-Turn List .......................... 39
Direct Help ........................................ 82
A
Activate........................................ 15, 96
B
Block............................................ 83, 84
Bluetooth
Activate ......................................... 96
Connect ........................................ 94
Pairing........................................... 92
Bluetooth ........... see Handsfree Module
C
Call
Dial Number .................................. 99
Phone Book ................................ 100
Preset ........................................... 99
Recent Calls ............................... 100
Call in Progress
Enter numerals ........................... 101
Hang up ...................................... 102
Muting ......................................... 101
Show Map ................................... 101
Use handsfree ............................ 101
Use Mobile Phone ...................... 102
CleverParking Live
Parking........................................ 107
Compass ........................................... 20
Configuration
NAVIGON Live............................ 110
Configuration ................................... 111
Connect ............................................. 94
Connection with Mobile Phone.......... 92
Conventions followed in this
manual................................................. 7
Costs ............................................... 105
Current Position
Save.............................................. 83
- 122 -
E
Energy................................. 14, 20, 120
Enter Coordinates ............................. 29
Entering data..................................... 24
F
Favourites ................................... 35, 41
G
Google Local Search ...................... 108
Index
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
GPS
Faulty reception ............................ 25
Initialise......................................... 26
Signals .......................................... 16
Symbols ........................................ 19
GPS Status........................................ 82
H
Handsfree Module
Activate ......................................... 96
Call................................................ 99
Call in Progress .......................... 101
Connect ........................................ 94
Connection with Mobile Phone ..... 92
Delete Device ............................... 96
Dial Number .................................. 99
Enter numerals ........................... 101
Hang up ...................................... 102
Import Phone Book ....................... 97
Import recent calls ........................ 98
Incoming Call ................................ 98
Incoming text message................. 98
Muting ......................................... 101
Open ............................................. 91
Pairing........................................... 92
Phone Book ................................ 100
Preset ................................... 99, 103
Recent Calls ............................... 100
Settings ............................... 103, 104
Show Map ................................... 101
SMS inbox .................................. 102
Symbols ........................................ 22
Use handsfree ............................ 101
Use Mobile Phone ...................... 102
Home Address
Edit................................................ 42
Home Address............................. 38, 41
Hotline ................................................. 8
I
Imported Addresses
From the phone book.................... 37
Outlook / Internet .......................... 36
Installation ......................................... 14
Index
K
Keyboard........................................... 23
L
Last Destinations ........................ 36, 41
Logbook ............................................ 89
M
Manual
Conventions.................................... 7
Symbols .......................................... 7
Manual .............................................. 19
Map
1-Click-Menu ................................ 52
Destination search........................ 65
Offroad.......................................... 64
Pedestrian .................................... 61
Preview......................................... 55
Reality View.................................. 60
Standard ....................................... 53
Track............................................. 63
Vehicle.......................................... 56
Memory card ..................................... 15
Menu ................................................. 25
Motion Sensor ................................... 51
Muting ............................................... 23
My Destinations................................. 27
My POIs ............................................ 70
MyPOIs ............................................. 70
MyRoutes .................................... 40, 47
N
Navigation
Block....................................... 83, 84
MyRoutes ............................... 40, 47
No GPS .................................. 40, 48
Route Profile........................... 39, 46
Start ........................................ 39, 46
Start Navigation ...................... 40, 47
Turn-by-Turn List .................... 39, 46
Unblock......................................... 83
- 123 -
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
Navigation Application
Start .............................................. 26
Navigation system
Description...................................... 9
Energy .......................................... 14
Installation..................................... 13
Memory card ................................. 15
No TMC ........................................ 15
Scope of Delivery............................ 8
Start .............................................. 17
Technical data ............................ 113
NAVIGON Live
Activate ......................................... 15
Configuration .............................. 110
Costs........................................... 105
Description...................................... 9
Installation..................................... 14
Settings ....................................... 110
Status.......................................... 111
Subscription ................................ 105
Symbols ........................................ 20
NAVIGON Sightseeing ...................... 78
Nearby............................................... 75
New Destination ................................ 27
O
Options .................................. 19, 25, 48
P
Pairing ............................................... 92
Parking
CleverParking Live...................... 107
Last Destination ............................ 75
Parking Close to Destination ........ 74
Pedestrian mode........................... 74
Phone ................ see Handsfree Module
Phone Book
Import Phone Book ....................... 97
Refresh ......................................... 97
Phone Book..................................... 100
- 124 -
POI
Direct Access................................ 34
in a City......................................... 33
Nationwide.................................... 32
NAVIGON Sightseeing ................. 78
Nearby .......................................... 31
POI on Your Route ....................... 76
Preset.............................................. 103
Preview TMC..................................... 85
R
Reality View ...................................... 60
Recalculate Route............................. 89
Recent Calls
Import recent calls ........................ 98
Recent Calls.................................... 100
Route Planning ................................. 42
Route points
Add ............................................... 43
Delete ........................................... 44
Order ............................................ 44
Starting Point ................................ 43
Route Profile ......................... 39, 46, 67
Routes
Load.............................................. 44
Manage......................................... 44
Route points ................................. 43
Route Profile................................. 46
Save ............................................. 44
Show............................................. 45
Simulation..................................... 45
Start Navigation ............................ 46
Starting Point ................................ 42
Turn-by-Turn List .......................... 46
Routes and Tracks
Load.............................................. 44
Planning........................................ 42
Routes and Tracks ............................ 42
Index
User's manual NAVIGON 40 Essential | Easy | Plus | Premium | Premium Live
S
Safety information ............................. 10
Scope of Delivery ................................ 8
Screenshots ...................................... 72
Service ................................................ 8
Settings
Configuration .............................. 111
Handsfree Module ...................... 104
NAVIGON Live............................ 110
Volume.......................................... 60
Settings Handsfree Module
Connection with Mobile Phone ..... 92
Delete Device ............................... 96
Preset ......................................... 103
Sightseeing Tours ............................. 80
Simulation
Exit ................................................ 46
Start .............................................. 45
SMS inbox ....................................... 102
Software keyboard ............................ 23
Status
NAVIGON Live............................ 111
Subscription..................................... 105
Support................................................ 8
Symbols
NAVIGON Live.............................. 20
Traffic Information......................... 21
Traffic Live .................................... 21
Symbols used in this manual .............. 7
T
Take Me Home............................ 38, 41
Technical data ................................. 113
TMC
Preview TMC ................................ 85
Recalculate Route ........................ 89
Show............................................. 87
Symbols ........................................ 21
Tuning Mode ................................. 89
Index
TMC Settings
Recalculate Route ........................ 89
TMC .............................................. 88
Traffic Information......................... 88
Tuning Mode................................. 89
Track
Load.............................................. 44
Record Track .......................... 20, 73
Trade marks ........................................ 8
Traffic Information
Preview TMC ................................ 85
Recalculate Route ........................ 89
Show............................................. 87
Symbols ........................................ 21
Traffic Live .................................. 110
Tuning Mode................................. 89
Traffic Live
Symbols ........................................ 21
Traffic Information....................... 110
Troubleshooting .............................. 119
Tuning Mode ..................................... 89
Turn-by-Turn List
Block............................................. 84
Show................................. 39, 46, 83
U
Unblock ............................................. 83
V
Volume .............................................. 60
W
Warranty.............................................. 7
Weather Live
Weather Service ......................... 106
Weather Service
Weather Live .............................. 106
- 125 -
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement