Emtek Barn Door Hardware Installation Instruction
Advertisement
Advertisement
FLAT TRACK SLIDING BARN DOOR HARDWARE
Face Mount Installation Instructions
General
Info
The wall or structure that your system will be mounted on must be designed to support a maximum door weight of 400 lbs.
Ensure that door panels are constructed with solid, structural material.
Do not install directly into drywall. Must be installed into wall blocking or header board.
Check with your contractor and/or your city of residence to confirm accordance with local building codes.
For best results, seek qualified building professionals for installation.
Tools
Required
19/32” 11/32” 19/64” 1-1/2”
5/16”
Allen
Wrench
7/32”
Allen
Wrench
3/32”
Allen
Wrench
What’s in the box
Hanger
Bolts
Stops
Hangers Anti-jumps Floor Guide
Track Fasteners Drywall
Anti-crushes
Post & Spacers
Track
Splice Kit (Required for 10’, 13’ or 16’ Lengths)
Bracket
Optional Soft Open/Close
Splice kit screws
Soft Open/Close Catch
4
Mark for Track
1
Use the track as a template to mark the center of the holes.
Tracks with splice kits have a unique hole spacing between splice.
Header board* Internal bracing
!
Do not install directly into
Drywall. Must attach to a preinstalled header board or the wall must be braced internally.
*Header board and anchor screws not included.
Center Line of track mounting holes
Track height = door panel height + 2-1/4”
Install track splice
(required for 10’, 13’, 16’ lengths)
2
Install Optional Soft Open/Close - Part 1
!
Mount the soft open/close on the bottom of the track and ensure that it is oriented in the correct direction for operation.
Direction of door
Direction of door
5
6
Secure Track
3
Drill 19/64” [7.54mm] pilot holes in marked locations for track fasteners.
Attach track to wall using track brackets and fasteners as shown.
!
Use supplied anti-crush discs if installing to an internally braced wall. NEVER attach directly to drywall.
Use 5/16” Allen
Wrench to install track screws
Use supplied spacers as necessary to ensure that the door has clearance from wall/ moldings.
4
Prep Door for Hangers & Floor Guide
Drill Holes in door for hanger bolt by using a
19/32” bit.
1 12 " 38.1
4 34 "
120.7
19/32
[15.1]
16 "
11.11
58 " 15.88
Route bottom, full length of door to receive floor mounted guide.
7
5
Install Anti-Jump
Install anti-jump flush to front of door.
8
6
Mount Hangers to Door
Tip: You may need to counterbore the back of the door for thick door applications.
Front of door
Back of door
Use 7/32” Allen
Wrench to install track screws
7
Hang the Door
Prior to hanging door on track rotate anti-jump toward front face of door as shown to disengage.
9
10
8
Adjust the Stops
Tighten set screws. Start with bottom set screws then move to top set screws with sufficient force to drive set screws into bar after final adjustment. Ensure the stops allow for the door to extend the desired length over the door opening. Adjust stops accordingly.
9
Install Floor Guide
Drill pilot holes for anchors using 11/32” drill bit. Mount floor guide with anchors and screws provided.
Wall
Tip: Install floor guide in a position where it won’t be exposed with door in the open or closed position.
11
10
Install Optional Soft Open/Close - Part 2
1. Move door to desired stop location.
2. Place soft catch under soft open/close as shown.
3. Mark location of soft catch.
4. Remove door from track
5. Install soft catch at marked location
6. Hang door on track
IN4-BARNFACEMNT REV 2 11-2-21
Copyright © 2021, EMTEK Products, Inc. an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of EMTEK Products, Inc. is prohibited.
!
cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Public link updated
The public link to your chat has been updated.
Advertisement