WADE-8072 User`s Manual
WADE-8072
Mini-ITX Board
User's Manual
Version 1.0d
Copyright © Portwell, Inc., 2010. All rights reserved.
All other brand names are registered trademarks of their respective owners.
Preface
Table of Contents
How to Use This Manual
Chapter 1 System Overview.......................................................................................................1-1
1.1 Introduction ....................................................................................................... 1-1
1.2 Check List........................................................................................................... 1-1
1.3 Product Specification........................................................................................ 1-2
1.3.1 Mechanical Drawing................................................................................ 1-5
1.4 System Architecture.......................................................................................... 1-7
Chapter 2 Hardware Configuration ...........................................................................................2-1
2.1
2.2
Jumper Setting ............................................................................................. 2-1
Connector Allocation.................................................................................. 2-7
Chapter 3 System Installation....................................................................................................3-1
3.1 Intel® ATOM CPU............................................................................................ 3-1
3.2 Main Memory .................................................................................................... 3-1
3.3 Installing the Single Board Computer............................................................ 3-2
3.3.1 Chipset Component Driver .................................................................... 3-2
3.3.2 Intel Integrated Graphics GMCH Chip ................................................ 3-2
3.3.3 Realtek Gigabit Ethernet Controller...................................................... 3-3
3.3.4 Audio Controller ...................................................................................... 3-3
3.4 Clear CMOS Operation .................................................................................... 3-3
3.5 WDT Function ................................................................................................... 3-4
3.6 GPIO.................................................................................................................... 3-6
Chapter 4 BIOS Setup Information............................................................................................4-1
4.1 Entering Setup ................................................................................................... 4-1
4.2 Main Menu......................................................................................................... 4-2
4.3 Standard CMOS Setup Menu.......................................................................... 4-3
4.4 IDE/SATA Adaptors Setup Menu ................................................................. 4-4
4.5 Advanced BIOS Features ................................................................................. 4-6
4.6 Advanced Chipset Features........................................................................... 4-11
4.7 Integrated Peripherals .................................................................................... 4-14
4.8 Power Management Setup............................................................................. 4-21
4.9 PnP/PCI Configurations................................................................................ 4-25
4.10 PC Health Status ........................................................................................... 4-26
4.11 Frequency/Voltage Control ........................................................................ 4-27
4.12 Default Menu................................................................................................. 4-28
4.13 Supervisor/User Password Setting............................................................ 4-30
4.14 Exiting Selection ............................................................................................ 4-32
Chapter 5 Troubleshooting ........................................................................................................5-1
5.1 Hardware Quick Installation........................................................................... 5-1
5.2 BIOS Setting ....................................................................................................... 5-2
Preface
5.3 FAQ ..................................................................................................................... 5-3
Appendix A
Appendix B
Preface
How to Use This Manual
The manual describes how to configure your system board to meet various operating
requirements. It is divided into five chapters, with each chapter addressing a basic
concept and operation of Single Host Board.
Chapter 1 : System Overview. Presents what you have in the box and give you an
overview of the product specifications and basic system architecture for this series
model of single host board.
Chapter 2 : Hardware Configuration. Shows the definitions and locations of Jumpers
and Connectors that you can easily configure your system.
Chapter 3 : System Installation. Describes how to properly mount the CPU, main
memory and Compact Flash to get a safe installation and provides a programming
guide of Watch Dog Timer function.
Chapter 4 : BIOS Setup Information. Specifies the meaning of each setup
parameters, how to get advanced BIOS performance and update new BIOS. In
addition, POST checkpoint list will give users some guidelines of trouble-shooting.
Chapter 5 : Troubleshooting. Provides various useful tips to quickly get its running
with success. As basic hardware installation has been addressed in Chapter 3, this
chapter will basically focus on system integration issues, in terms of backplane setup,
BIOS setting, and OS diagnostics.
The content of this manual is subject to change without prior notice. These changes
will be incorporated in new editions of the document. Portwell may make
supplement or change in the products described in this document at any time.
Updates to this manual, technical clarification, and answers to frequently asked
questions will be shown on the following web site : http://www.portwell.com.tw/.
System Overview
Chapter 1
System Overview
1.1
Introduction
Portwell Inc., a world-leading innovator in the Industrial PC (IPC) market and
develop a new Intel® Mini-ITX board with latest Intel® platform for embedded
application. The Portwell WADE-8072 takes advantage of Intel® 45-nanometer Hi-k
process technology — the first generation of low-power IA-32 microarchitecture
specially designed for Embedded Platform and can support Intel® 945GSE chipset
with the ICH7-M, can provide the low power consumption for fanless applications
such as POS, ATM, Kiosk, Medical and Digital Signage.
WADE-8072 supports dual display by VGA and 24-bit LVDS. With its
display-enriched interface, WADE-8072 can support various multimedia devices
and enriched IO interfaces that can supply various USB and COM devices.
WADE-8072 supports SO-DIMM memory slot for DDR2 SDRAM up to 2GB, and
comes with PS/2 Keyboard and Mouse, 1 x RS232/422/485, 3 x RS232, 2 x SATA, 1 x
IDE, dual Gigabit Ethernet, 6 x USB2.0 ports. It also support CompactFlash Socket,
one PCI slot and one PCIEx1 Slot for embedded application usage.
1.2
Check List
The WADE-8072 package should cover the following basic items
9
9
9
9
One WADE-8072 Mini ITX Main Board
One Serial ATA cable
One I/O Shield bracket
One Installation Resources CD-Title
If any of these items is damaged or missing, please contact your vendor and keep all
packing materials for future replacement and maintenance.
WADE-8071 User’s Manual
1-1
System Overview
1.3
Product Specification
z Main processor
- Support Intel Atom processor N270
- CPU bus clock: 667/533 MHz
z Chipset
Intel® 945GSE and ICH7-M
z Main Memory
- Support signal channel DDR2 memory interface
- Up to 2GB DDR2 533 SDRAM on SO-DIMM socket
z System BIOS
AWARD BIOS
z Expansion Interface
One PCI and one PCI Express x1 slot
z SATA Interface
Two SATA ports
z Serial Ports
Support three RS-232 serial ports, one RS-232/422/485 selectable
z IR Interface
N/A
z Parallel Port
One LPT port
z USB Interface
Support six USB (Universal Serial Bus) ports (four at rear, two on-board for
internal devices)
z PS/2 Mouse and Keyboard Interface
Support dual 6-pin mini-DIN connector at rear I/O panel for PS/2
keyboard/mouse
z Audio Interface
Connector of Mic-in/Line-out
z Real Time Clock/Calendar (RTC)
Support Y2K Real Time Clock/Calendar
z Watchdog Timer
- Support WDT function through software programming for enable/disable and
interval setting
- Generate system reset
z On-board VGA
- Intel 945GSE Integrated GMA950 Graphics device
- Intel DVMT 3.0 supports up to 128MB video memory
WADE-8071 User’s Manual
1-2
System Overview
z On-board Ethernet LAN
Dual Gigabit Ethernet (10/100/ 1000 Mbits/sec) LAN ports
z High Driving GPIO
Onboard programmable 8-bit Digital I/O interface
z Cooling Fans
Support two 3-pin power connector for CPU cooler and one 3-pin power
connector for system fan
z System Monitoring Feature
Monitor system temperature and major power sources, etc
z Outline Dimension (L X W):
170mm (6.69”) X 170mm (6.69”)
z Power Requirements:
+12V(System)@0.35A; [email protected]; [email protected]
Configuration:
CPU Type
SBC BIOS
Memory
VGA Card
VGA Driver
LAN Card
LAN Driver
Audio Card
Audio Driver
Chip Driver
USB2.0 Driver
SCSI Card
SCSI HDD
SATA HDD
Compact Flash
CDROM
Power Supply
WADE-8071 User’s Manual
System Configuration
Intel® Atom™ N270 1.60GHz (133*12) L2: 512K FSB:533MHz
Portwell,Inc.WADE-8072 BIOS Rev.:R1.00.W0(07012009)
Transcend DDR2 533 512MB (ELPIDA E5108AGBG-5C-E)
Onboard Intel® 845GSE Express Chipset
Mobile Intel® 945 Express Chipset Family Version 6.14.10.4926
Onboard Realtek RTL8111C Network Chipset
Realtek PCIe GBE Family Controller Version 5.728.604.2009
Onboard Realtek ALC662 Audio Chipset
Realtek High Definition Audio Version 5.10.0.5874
Intel® Chipset Device Software Version 9.0.0.1008
Intel® 82801G(ICH7 Family) USB2 Enhanced Host Controller
Version 8.2.0.1008
Adaptec AIC-7892
Seagate ST39173WAS 19GB
Seagate ST3802110AS 80GB
Apacer 256MB
LITE-ON LH 20A1S DVD-ROM
Portwell. Inc PW-330ATXE-12V
1-3
System Overview
Programs for loading both CPU & VGA: Run Burning Test V5.3
RUN time: 10 / 30 Minutes.
Item
Power ON
System +12V
System +3.3V
System +5V
System+ Device +12V
System+ Device +5V
USB Loading Test
0.3A
0.64A
1.29A
0.54A
2.12A
Full Loading
10Min
Full Loading
30Min
0.35A
0.82A
2.44A
0.55A
3.2A
4.8A / 540mA
0.35A
0.78A
2.49A
0.54A
3.15A
z Operating Temperature:
0°C ~ 55°C
z Storage Temperature:
-20°C ~ 80°C
z Relative Humidity:
5% ~ 90%, non-condensing
WADE-8071 User’s Manual
1-4
System Overview
1.3.1
Mechanical Drawing
WADE-8071 User’s Manual
1-5
System Overview
WADE-8071 User’s Manual
1-6
System Overview
1.4
System Architecture
All of details operating relations are shown in WADE-8072 series System Block
Diagram
SDVO
WADE-8072 System Block Diagram
WADE-8071 User’s Manual
1-7
Hardware Configuration
Chapter 2
Hardware Configuration
This chapter indicates jumpers’, headers’ and connectors’ locations. Users may find
useful information related to hardware settings in this chapter. The default settings
are indicated with a star sign (Ì).
2.1
Jumper Setting
In order to customize WADE-8072’s features for users, in the following sections,
Short means covering a jumper cap over jumper pins; Open or N/C (Not Connected)
means removing a jumper cap from jumper pins. Users can refer to Figure 2-1 and
Figure 2-2 for the Jumper locations.
WADE-8071 User’s Manual
2-1
Hardware Configuration
Figure 2-1 WADE-8072 Top-side Jumper and Connector Locations
WADE-8071 User’s Manual
2-2
Hardware Configuration
Figure 2-2 WADE-8072 Bottom-side Connector Locations
WADE-8071 User’s Manual
2-3
Hardware Configuration
Jumper List
JP1
RS232/422/485 selection jumper for COM port 2
JP2
RS232/powered +12V/powered +5V select for COM port 3
JP3
RS232/powered +12V/powered +5V select for COM port 4
JP4
LVDS Panel Logic/LCD Drive Voltage Selection
JP5
LVDS Panel Backlight Unit Ignition Logic/Voltage Selection
JP6
Super I/O WDTO# Gate Control
JP7
CMOS Normal / Clear Jumper
JP8
Auto Power Button Jumper
z
JP1: RS232/422/485 selection jumper for COM port 2 (J2 Top)
21 19 17 15 13 11 9 7 5 3 1
RS-232
21 19 17 15 13 11 9 7 5 3 1
22 20 18 16 14 12 10 8 6 4 2
21 19 17 15 13 11 9 7 5 3 1
21 19 17 15 13 11 9 7 5 3 1
RS-422
22 20 18 16 14 12 10 8 6 4 2
21 19 17 15 13 11 9 7 5 3 1
21 19 17 15 13 11 9 7 5 3 1
RS-485
22 20 18 16 14 12 10 8 6 4 2
JP3
5-6,9-11,10-12,15-17,16-18 Short
3-4,7-9,8-10,13-15,14-16,21-22 Short
1-2,7-9,8-10,19-20 Short
Function
RS-232 Ì
RS-422
RS-485
z JP2: RS232/powered +12V/powered +5V select for COM port 3 (J10)
RS232 Mode:
3-4 Short
WADE-8071 User’s Manual
5 3 1
6 4 2
JP2
Function
RS-232 Ì
2-4
Hardware Configuration
Powered +5V RS232 Mode:
1-3 Short
5 3 1
6 4 2
JP2
Function
Powered +5V RS-232
Powered +12V RS232 Mode:
z
5 3 1
6 4 2
JP2
3-5 Short
Function
Powered +12V RS-232
JP3: RS232/powered +12V/powered +5V select for COM port 4 (J11)
RS232 Mode:
3-4 Short
5 3 1
6 4 2
JP3
Function
RS-232 Ì
Powered +5V RS232 Mode:
1-3 Short
WADE-8071 User’s Manual
5 3 1
6 4 2
JP3
Function
Powered +5V RS-232
2-5
Hardware Configuration
Powered +12V RS232 Mode:
5 3 1
6 4 2
JP3
Function
Powered +12V RS-232
3-5 Short
z
JP4: LVDS Panel Logic/LCD Drive Voltage Selection
JP4
1-3 Short
3-4 Short
3-5 Short
Function
3.3 V
12 V
5VÌ
JP5: LVDS Panel Backlight Unit Ignition Logic/Voltage Selection
JP5
1-3, 2-4 Short
1-3, 4-6 Short
3-5, 2-4 Short
3-5, 4-6 Short
z
Function
5 V, Active high Ì
12 V, Active high
5 V, Active low
12 V, Active low
JP6: Super I/O WDTO# Gate Control
If WTDO# asserts after Watch Dog Timer expires, system reboots itself.
JP6
1-2 Short
2-3 Open
z
JP7: CMOS Normal / Clear Jumper
JP7
1-2 Short
2-3 Short
z
Function
Enable WTDO# function. Ì
Disable WTDO# function.
Function
Clear CMOS Disable (Normal) Ì
Clear CMOS Enable (Clear)
JP8: Auto Power Button
JP8
1-2 Short
Function
If a jumper is populated, system boots itself as long as 5VSB
exists.
WADE-8071 User’s Manual
2-6
Hardware Configuration
2.2
Connector Allocation
I/O peripheral devices are connected to the interface connectors
Connector List
J1
VGA Connector
J2
COM port 1/2 (bottom: COM1; top: COM2)
J3
Audio jack (green: Line out; pink: Mic in)
J4
PS2 keyboard / mouse connector
J5
USB 2/3 connector; LAN RJ-45 connector 1
J6
USB 0/1 connector; LAN RJ-45 connector 2
J7
Printer Port pin header
J8
TPM 1.2 pin header
J9
USB 6/7 pin header
J10
COM port 3 pin header
J11
COM port 4 pin header
J12
CASE OPEN pin header
J13
LVDS panel signal connector
J14
LVDS panel backlight unit connector
J15
44-pin IDE connector (Must be configured as an IDE slave device)
J17
DDR2 SO-DIMM Socket
J18
PCI-32 slot
J20
SATA connector
J21
SATA connector
J23
Front panel control and LED/Buzzer pin header
J24
Battery Holder
J26
20-pin ATX Power Supply Connector
J27
4-pin CPU Fan Connector
J28
3-pin System Fan Connector
J29
J30
Specified PCI Express x4 connector
(Not support common PCI Express x1 cards)
Compact Flash Card Socket (Hardwired as an IDE master device)
J31
GPIO pin header
J32
Mini PCI-Express Socket
WADE-8071 User’s Manual
2-7
Hardware Configuration
z
J1: VGA Connector
5
1
10
6
15
11
PIN No.
1
3
5
7
9
11
13
15
z
Signal Description
RED
BLUE
Ground
Ground
NC
ID1
HSYNC
DDCCLK
PIN No.
2
4
6
8
10
12
14
Signal Description
GREEN
ID0
Ground
Ground
Ground
DDCDATA
VSYNC
J2: COM port 1/2 (bottom: COM1; top: COM2)
1
5
6
9
-COM1
PIN No.
1
2
3
4
5
6
7
8
9
Signal Description
RS-232
DCD (Data Carrier Detect)
RXD (Receive Data)
TXD (Transmit Data)
DTR (Data Terminal Ready)
GND (Ground)
DSR (Data Set Ready)
RTS (Request to Send)
CTS (Clear to Send)
RI
WADE-8071 User’s Manual
2-8
Hardware Configuration
-COM2
PIN No.
1
2
3
4
5
6
7
8
9
z
RS-485
DATADATA+
NC
NC
GND
NC
NC
NC
NC
J3: Audio Jack
PIN No.
Green
Pink
z
Signal Description
RS-232
RS-422
DCD (Data Carrier TXDetect)
RXD (Receive Data)
TX+
TXD (Transmit Data)
RX+
DTR (Data Terminal RXReady)
GND (Ground)
GND
DSR (Data Set Ready)
NC
RTS (Request to Send)
NC
CTS (Clear to Send)
NC
RI (Ring Indicator)
NC
Signal Description
Line Out1
Mic1
J7: Parallel port pin header
PIN No.
1
3
5
7
9
11
13
15
17
19
21
23
25
Signal Description
Strobe#
Data 0
Data 1
Data 2
Data 3
Data 4
Data 5
Data 6
Data 7
Acknowledge#
Busy
Paper Empty
Printer Select
WADE-8071 User’s Manual
PIN No.
2
4
6
8
10
12
14
16
18
20
22
24
26
Signal Description
Auto Form Feed#
Error#
Initialization#
Printer Select IN#
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
NC
2-9
Hardware Configuration
z
J8: TPM 1.2 pin header
PIN No.
1
3
5
7
9
11
13
15
17
19
z
PIN No.
2
4
6
8
10
12
14
16
18
20
Signal Description
Ground
NC
+5V
LAD2
LAD1
Ground
SMBDATA
SERIRQ
NC
NC
PIN No.
2
4
6
8
10
Signal Description
+5V
DATADATA+
Ground
Ground
J9: USB 6/7 connector
PIN No.
1
3
5
7
z
Signal Description
Clock (33MHz)
LFRAME#
Reset#
LAD3
+3.3V
LAD0
SMBCLK
+3.3V Dual
Ground
NC
Signal Description
+5V
DATADATA+
Ground
J10: COM port 3 pin header
Pin No.
1
2
3
4
5
6
7
8
9
10
Signal Description
Data Carrier Detect
Data Set Ready
Receive Data
Request To Send
Transmit Data
Clear To Send
Data Terminal Ready
Ring Indicator (Powered +5V/+12V with JP2 selection)
Ground
NC
WADE-8071 User’s Manual
2-10
Hardware Configuration
z
J11: COM port 4 pin header
Pin No.
1
2
3
4
5
6
7
8
9
10
z
Signal Description
Data Carrier Detect
Data Set Ready
Receive Data
Request To Send
Transmit Data
Clear To Send
Data Terminal Ready
Ring Indicator (Powered +5V/+12V with JP2 selection)
Ground
NC
J13: LVDS panel signal connector
PIN No.
Signal Description
PIN No.
Signal Description
1
LVDS channel A data0+
2
LVDS channel A data03
LVDS channel A data1+
4
LVDS channel A data15
LVDS channel A data2+
6
LVDS channel A data27
LVDS channel A data3+
8
LVDS channel A data39
LVDS channel A clock+
10
LVDS channel A clock11
LVDS channel B data0+
12
LVDS channel B data013
LVDS channel B data1+
14
LVDS channel B data115
LVDS channel B data2+
16
LVDS channel B data217
LVDS channel B data3+
18
LVDS channel B data319
LVDS channel B clock+
20
LVDS channel B clock21
LVDS DDC data *
22
LVDS DDC clock *
NC
23
Ground
24
25
Ground
26
Ground
27
Power depends on JP4
28
Power depends on JP4
29
NC
30
Power depends on JP4
* DDC: Display Data Channel. EDID support for flat panel display.
WADE-8071 User’s Manual
2-11
Hardware Configuration
z
J14: LVDS panel backlight unit connector
5
PIN No.
1
2
3
4
5
z
Backlight enable
Ground
+12V
Ground
+5V
J23: Front panel control and LED/Buzzer connector
PIN No.
1
z
Signal Description
3
5
7
Signal Description
HDD LED (+)
w/150-ohm
pull-up
HDD LED (-)
Reset Button (+)
Reset Button (-)
11
13
Power Button (-)
Power Button (+)
PIN No.
2
4
6
8
10
12
14
Signal Description
Power LED (+)
w/ 330-ohm pull-up
NC
Power LED (-)
Buzzer (+)
NC
NC
Buzzer (-)
J26: ATX power connector
PIN No.
1
3
5
7
9
11
13
15
17
19
Signal Description
+3.3V
Ground
Ground
Ground
+5V stand by
+3.3V
Ground
Ground
Ground
+5V
WADE-8071 User’s Manual
PIN No.
2
4
6
8
10
12
14
16
18
20
Signal Description
+3.3V
+5V
+5V
PWR_OK
+12V
-12V
PS_ON#
Ground
-5V
+5V
2-12
Hardware Configuration
z
J27: 4-pin CPU Fan Connector
PIN No.
1
2
3
4
z
Ground
+12V
Fan speed sense
Fan speed control (PWM)
J28: 3-pin system fan connector
PIN No.
1
2
3
z
Signal Description
Signal Description
Ground
Fan speed control (voltage control)
Fan speed sense
J31: 8-bit GPIO pin header 2
PIN No.
1
3
5
7
9
Signal Description
GPIO50
GPIO51
GPIO52
GPIO53
Ground
WADE-8071 User’s Manual
PIN No.
2
4
6
8
10
Signal Description
GPIO60
GPIO61
GPIO62
GPIO63
+5V
2-13
System Installation
Chapter 3
System Installation
This chapter provides you with instructions to set up your system. The additional
information is enclosed to help you set up onboard PCI device and handle Watch Dog
Timer (WDT) and operation of GPIO in software programming.
3.1
Intel® ATOM CPU
WADE-8072 onboard uses Intel Atom N270 CPU 1.6GHz processor.
Introducing Intel Atom processor, a new microprocessor designed from the ground
up for mobility, with a mobile-optimized chipset. Intel mobile processor innovative
design techniques allow faster execution of instructions at lower power.
3.2
Main Memory
WADE-8072 provide 1 x 200-pin SO-DIMM sockets which supports 400/533
DDR2-SDRAM as main memory, Non-ECC (Error Checking and Correcting),
non-register functions. The maximum memory size can be up to 2GB capacity.
Memory clock and related settings can be detected by BIOS via SPD interface.
For system compatibility and stability, do not use memory module without brand.
Memory configuration can be one double-sided DIMM. Watch out for the contact and
lock integrity of memory module with socket, it will impact on the system reliability.
The following normal procedures are installing memory module into memory socket.
Before locking, make sure that all modules have been fully inserted into the card
slots.
CPU FSB
533MHz
Memory Frequency
400 MHz
533 MHz
Bandwidth
4.2GB/s
Single Channel DDR
Bandwidth
3.2GB/s
4.2GB/s
Note:
To maintain system stability, don’t change any of DRAM parameters in BIOS setup to
upgrade system performance without acquiring technical information.
WADE-8071 User’s Manual
3-1
System Installation
Memory frequency / CPU FSB synchronization
WADE-8072 supports different memory frequencies depending on the CPU front
side bus and the type of DDR2 SO-DIMM.
CPU FSB
533 MHz
3.3
Memory Frequency
400/533MHz
Installing the Single Board Computer
To install your WADE-8072 into standard chassis or proprietary environment, please
perform the following:
Step 1 : Check all jumpers setting on proper position
Step 2 : Install memory module on right position
Step 3 : Place WADE-8072 into the dedicated position in the system
Step 4 : Attach cables to existing peripheral devices and secure it
WARNING
Please ensure that SBC is properly inserted and fixed by mechanism.
Note:
Please refer to section 3.3.1 to 3.3.4 to install INF/VGA/LAN/Audio drivers.
3.3.1
Chipset Component Driver
The chipset on WADE-8072 is a new chipset that a few old operating systems might
not be able to recognize. To overcome this compatibility issue, for Windows
Operating Systems such as Windows 2000/XP/Vista, please install its INF before any
of other Drivers are installed. You can find very easily this chipset component driver
in WADE-8072 CD-title.
3.3.2
Intel Integrated Graphics GMCH Chip
Using Intel® 945GSE GMCH with Media Accelerator (GMA) 950 graphics integrated
chipset is aimed to gain an outstanding graphic performance. Shared 8 accompany it
to 128MB system DDR2-SDRAM with Total Graphics Memory. This combination
makes WADE-8072 an excellent piece of multimedia hardware.
Drivers Support
Please find Springdale GMCH driver in the WADE-8072 CD-title. Drivers support
Windows-2000, Windows XP, and Windows Vista.
WADE-8071 User’s Manual
3-2
System Installation
3.3.3
Realtek Gigabit Ethernet Controller
Drivers Support
Please find Realtek RTL8111D LAN driver in /Ethernet directory of WADE-8072
CD-title. The drivers support Windows 2000 /XP/Vista.
LED Indicator (for LAN status)
WADE-8072 provides two LED indicators to report Realtek RTL8111D Gigabit
Ethernet interface status. Please refer to the table below as a quick reference guide.
8111D
Color
Name of LED
Status
LED
Orange
LAN Linked & Active LED
Orange
Speed
LED
3.3.4
LAN speed LED
Green
Operation of Ethernet Port
Linked
Active
On
Blinking
Giga
Mbps
100
Mbps
10
Mbps
Orange
Green
Off
Audio Controller
Please find Realtek ALC662 Audio driver form WADE-8072 CD-title. The drivers
support Windows 2000 /XP/Vista.
3.4
Clear CMOS Operation
The following table indicates how to enable/disable Clear CMOS Function hardware
circuit by putting jumpers at proper position.
3
2
1
Normal
3
2
1
Clear
JP7 : CMOS Normal / Clear Jumper
JP7
1-2 Short
2-3 Short
Function
Clear CMOS Disable (Normal) Ì
Clear CMOS Enable (Clear)
WADE-8071 User’s Manual
3-3
System Installation
3.5
WDT Function
The working algorithm of the WDT function can be simply described as a counting
process. The Time-Out Interval can be set through software programming. The
availability of the time-out interval settings by software or hardware varies from
boards to boards.
WADE-8072 allows users to control WDT through dynamic software programming.
The WDT starts counting when it is activated. It sends out a signal to system reset or
to non-maskable interrupt (NMI), when time-out interval ends. To prevent the
time-out interval from running out, a re-trigger signal will need to be sent before the
counting reaches its end. This action will restart the counting process. A well-written
WDT program should keep the counting process running under normal condition.
WDT should never generate a system reset or NMI signal unless the system runs into
troubles.
The related Control Registers of WDT are all included in the following sample
program that is written in C language. User can fill a non-zero value into the
Time-out Value Register to enable/refresh WDT. System will be reset after the
Time-out Value to be counted down to zero. Or user can directly fill a zero value into
Time-out Value Register to disable WDT immediately. To ensure a successful
accessing to the content of desired Control Register, the sequence of following
program codes should be step-by-step run again when each register is accessed.
Additionally, there are maximum 2 seconds of counting tolerance that should be
considered into user’ application program. For more information about WDT, please
refer to Winbond W83627UHG data sheet.
There are two PNP I/O port addresses that can be used to configure WDT,
1) 0x2E:EFIR (Extended Function Index Register, for identifying CR index number)
2) 0x2F:EFDR (Extended Function Data Register, for accessing desired CR)
Below are some example codes, which demonstrate the use of WDT.
// Enter Extended Function Mode
outp(0x002E, 0x87);
outp(0x002E, 0x87);
// Enable Pin 77 as WDTO#
// Select Logic Device 8
outp(0x002E, 0x07);
outp(0x002F, 0x08);
// Active Logic Device 8
outp(0x002E, 0x30);
outp(0x002F, 0x01);
WADE-8071 User’s Manual
3-4
System Installation
// Select Count Mode
outp(0x002E, 0xF5);
outp(0x002F, (inp(0x002F) & 0xF7) | ( Count-mode Register & 0x08));
// Specify Time-out Value
outp(0x002E, 0xF6);
outp(0x002F, Time-out Value Register );
// Disable WDT reset by keyboard/mouse interrupts
outp(0x002E, 0xF7);
outp(0x002F, 0x00);
// Exit Extended Function Mode
outp(0x002E, 0xAA);
Definitions of Variables:
Value of Count-mode Register :
1) 0x00 -- Count down in seconds (Bit3=0)
2) 0x08 -- Count down in minutes (Bit3=1)
Value of Time-out Value Register :
1) 0x00 -- Time-out Disable
2) 0x01~0xFF -- Value for counting down
WADE-8071 User’s Manual
3-5
System Installation
3.6
GPIO
The WADE-8072 provides 8 input/output ports that can be individually configured
to perform a simple basic I/O function. Users can configure each individual port to
become an input or output port by programming register bit of I/O Selection. To
invert port value, the setting of Inversion Register has to be made. Port values can be
set to read or write through Data Register.
The GPIO port is located on J31 shown as follows. Please note: DO NOT
SHORT-CIRCUIT PIN 9 AND 10 OF J31!
J31 : 8-bit GPIO pin header 2
PIN No.
1
3
5
7
9
Signal Description
GPIO50
GPIO51
GPIO52
GPIO53
Ground
PIN No.
2
4
6
8
10
Signal Description
GPIO60
GPIO61
GPIO62
GPIO63
+5V
All 8 GPIO pins come from W83627UHG, Winbond. All of them are TTL-level,
bi-directional pins and open-drain outputs with 12mA sink capability except GP52
which is with 8mA sink capability.
Users can refer to W83627UHG, Winbond datasheet to configure each individual port
to become an input or output port by programming register bit of I/O Selection. To
invert port value, the setting of Inversion Register has to be made. Port values can be
set to read or write through Data Register.
WADE-8071 User’s Manual
3-6
BIOS Setup Information
Chapter 4
BIOS Setup Information
WADE-8072 is equipped with the AWARD BIOS stored in Flash ROM. These BIOS
has a built-in Setup program that allows users to modify the basic system
configuration easily. This type of information is stored in CMOS RAM so that it is
retained during power-off periods. When system is turned on, WADE-8072
communicates with peripheral devices and checks its hardware resources against the
configuration information stored in the CMOS memory. If any error is detected, or
the CMOS parameters need to be initially defined, the diagnostic program will
prompt the user to enter the SETUP program. Some errors are significant enough to
abort the start-up.
4.1
Entering Setup
Turn on or reboot the computer. When the message “Hit <DEL> if you want to run
SETUP” appears, press <Del> key immediately to enter BIOS setup program.
If the message disappears before you respond, but you still wish to enter Setup,
please restart the system to try “COLD START” again by turning it OFF and then
ON, or touch the "RESET" button. You may also restart from “WARM START” by
pressing <Ctrl>, <Alt>, and <Delete> keys simultaneously. If you do not press the
keys at the right time and the system will not boot, an error message will be displayed
and you will again be asked to,
Press <F1> to Run SETUP or Resume
In HIFLEX BIOS setup, you can use the keyboard to choose among options or modify
the system parameters to match the options with your system. The table below will
show you all of keystroke functions in BIOS setup.
↑↓→ ←
Enter
+ / - /PU /PD
ESC
F1
F2
F5
F6
F7
F9
F10
General Help
: Move
: Select
: Value
: Exit
: General Help
: Item Help
: Previous Values
: Fail-Safe Defaults
: Optimized Defaults
: Menu in BIOS
: Save
WADE-8071 User’s Manual
4-1
BIOS Setup Information
4.2
Main Menu
Once you enter WADE-8072 AWARD BIOS CMOS Setup Utility, a Main Menu is
presented. The Main Menu allows user to select from eleven setup functions and two
exit choices. Use arrow keys to switch among items and press <Enter> key to accept
or bring up the sub-menu.
Note:
It is strongly recommended to reload Optimal Setting if CMOS is lost or BIOS is
updated.
WADE-8071 User’s Manual
4-2
BIOS Setup Information
4.3
Standard CMOS Setup Menu
This setup page includes all the items in standard compatible BIOS. Use the arrow
keys to highlight the item and then use the <PgUp>/<PgDn> or <+>/<-> keys to
select the value or number you want in each item and press <Enter> key to certify it.
Follow command keys in CMOS Setup table to change Date, Time, Drive type,
Video, and Halt on status.
Note:
Oblique items are base on memory capacity which user adopts on single board.
„ Menu Selections
Item
Options
Date
mm:dd:yy
Time
hh:mm:ss
IDE Channel 0
Master
Options are in its sub
IDE Channel 0
menu
Slave
SATA Channel 1
SATA Channel 2
Video
EGA/VGA, CGA 40
CGA 80, MONO
Halt On
All, But Keyboard
WADE-8071 User’s Manual
Description
Change the day, month, year and century
Change the internal clock
Press <Enter> to enter next page for detail
hard drive settings
Select the default video device
Select the situation in which you want the
4-3
BIOS Setup Information
Base Memory
640K
Extended
Memory
Total Memory
N/A
4.4
N/A
BIOS to stop the POST process and notify
you
Displays the amount of conventional
memory detected during boot up
Displays the amount of extended memory
detected during boot up
Displays the total memory available in the
system
IDE/SATA Adaptors Setup Menu
The IDE/SATA adapters control the IDE/SATA devices, such as hard disk drive or
CD-ROM drive. It uses a separate sub menu to configure each hard disk drive.
Note:
The oblique items are meaning base on what kind of storage device user employs.
WADE-8071 User’s Manual
4-4
BIOS Setup Information
„ Menu Selections
Item
Options
IDE HDD
Press Enter
Auto-detection
IDE Channel 0
Master /
Extended IDE
Drive
None
Auto
Manual(IDE)
Access Mode
CHS, LBA(IDE)
Large, Auto
Auto Display your
disk drive size
Capacity
Description
Press Enter to auto-detect the HDD on this
channel. If detection is successful, it fills
the remaining fields on this menu.
Selecting ‘manual’ lets you set the
remaining fields on this screen. Selects the
type of fixed disk. "User Type" will let you
select the number of cylinders, heads, etc.
Note: PRECOMP=65535 means NONE !
Choose the access mode for this hard disk
Disk drive capacity (Approximated). Note
that this size is usually slightly greater than
the size of a formatted disk given by a disk
checking program.
The following options are selectable only if the ‘IDE Primary Master’ item is set to ‘Manual’
Cylinder
Head
Precomp
Min=0, Max=65535
Min=0, Max=255
Min=0, Max=65535
Landing zone
Sector
Min=0, Max=65535
Min=0, Max=255
WADE-8071 User’s Manual
Set the number of cylinders for hard disk
Set the number of read/write heads
**** Warning: Setting a value of 65535
means no hard disk
****
Number of sectors per track
4-5
BIOS Setup Information
4.5
Advanced BIOS Features
This section allows you to configure your system for basic operation. You have the
opportunity to select the system’s default speed, boot-up sequence, keyboard
operation, and security.
WADE-8071 User’s Manual
4-6
BIOS Setup Information
Delay Prior To Thermal
This field has been used to select the time that would force the CPU to a 50% duty
cycle when it exceeds its maximum operating temperature therefore protecting the
CPU and the system board from overheating to ensure a safe computing
environment.
Limit CPUID MaxVal
Set limit CPUID MaxVal to 3. should be” Disabled” for Windows XP.
The choice: Disabled, Enabled.
C1E Function
CPU C1E Function Select.
The choice: Auto, Disabled.
CPU C State Capability
User can select the lowest C state supported according as CPU and MB.
The choice: Disabled, C2, C4.
Execute Disabled Bit
When disabled, forces the XD feature flag to always return 0.
The choice: Enabled, Disabled.
WADE-8071 User’s Manual
4-7
BIOS Setup Information
Hard Disk Boot Priority
Select Hard Disk Boot Device Priority. Use <↑> or <↓> to select a device, then press
<+> to move it up, or <-> to move it down the list. Press <ESC> to exit this menu.
Virus Warning
Allow you to choose the VIRUS warning feature for IDE Hard Disk boot sector
protection. If this function is enabled and someone attempt to write data into this
area, BIOS will show a warning message on screen and alarm beep.
Enabled
Disabled
Activates automatically when the system boots up causing a
warning message to appear when anything attempts to access the
boot sector or hard disk partition table.
No warning message will appear when anything attempts to access
the boot sector or hard disk partition table.
CPU L1 Cache/L2 Cache
These two categories speed up memory access.
CPU/chipset design.
Enabled
Disabled
However, it depends on
Enable Cache
Disable Cache
Hyper-Threading Technology
“Enabled” for Windows XP and Linux 2.4.X (OS optimized for Hyper-Threading
Technology and “Disabled” for other OS (OS not optimized for Hyper-Threading
Technology).
The choice: Enabled, Disabled.
Quick Power On Self Test
Allows the system to skip certain tests while booting. This will decrease the time
needed to boot the system.
Enabled
Disabled
Enable quick POST
Normal POST
First/Second/Third Boot Device
Select your Boot Device Priority.
The choice: LS120, Hard Disk, CDROM, ZIP 100, USB-FDD, USB-ZIP, USB-CDROM,
LAN and Disabled.
WADE-8071 User’s Manual
4-8
BIOS Setup Information
Boot Other Device
Select your Boot Device Priority.
The choice: Enabled, Disabled.
PXE Function Control
Select your boot from PXE.
The choice: Enabled, Disabled.
Boot Up NumLock Status
Select power on state for NumLock.
The choice: Off, On.
Gate A20 Option
Fast - lets chipset control GateA20 and Normal – a pin in the keyboard controller
controls GateA20. Default is fast.
The choice: Normal, Fast.
Typematic Rate Setting
Keystrokes repeat at a rate determined by the keyboard – when enabled, the
typematic rate and typematic delay can be selected.
The choice: Disabled, Enabled.
※Typematic Rate (Chars/sec)
The rate at which character repeats when you hold down a key.
The choice: 6, 8, 10, 12, 15, 20, 24, and 30. (Default 6)
※Typematic delay (Msec)
The delay before keystrokes begin to repeat.
The choice: 250, 500, 750, and 1000. (Default 250)
WADE-8071 User’s Manual
4-9
BIOS Setup Information
Security Option
Select whether the password is required every time the system boots or only when
you enter setup.
System
Setup
The system will not boot and access to Setup will be denied if the
correct password is not entered at the prompt.
The system will boot, but access to Setup will be denied if the correct
password is not entered at the prompt.
APIC Mode
The choice: Enabled, Disabled.
MPS Version Control For OS
The choice: 1.1, 1.4
OS Select For DRAM > 64MB
Select OS/2 only if you are running OS/2 operating system with greater than 64MB
of RAM on the system.
The choice: Non-OS2, OS2.
Report No FDD For WIN 95
The choice: No, Yes.
Small Logo (EPA) Show
The choice: Enabled, Disabled.
WADE-8071 User’s Manual
4-10
BIOS Setup Information
4.6
Advanced Chipset Features
This section allows you to configure the system based on the specific features of the
Intel 945GSE chipset. This chipset manages bus speeds and access to system memory
resources, such as DDR2 SO-DIMM and the external cache. It must be stated that
these items should never need to be altered. The default settings have been chosen
because they provide the best operating conditions for the system. The only time user
might consider making any changes would be if you discovered that data was being
lost while during system operation.
DRAM Timing Selectable
This option provides DIMM plug-and-play support by serial presence detect (SPD)
mechanism via the system management bus (SMBUS) interface.
The choice: Manual, By SPD.
CAS Latency Time
This option controls the number of SCLKs between the time a read command is
sampled by the DRAMs and the time the GMCH samples correspondent data from
the DRAMs.
The choice: 5, 4, 3, 6, and Auto.
WADE-8071 User’s Manual
4-11
BIOS Setup Information
DRAM RAS# to CAS# Delay
This option controls the number of SCLKs (SDRAM Clock) from a row activate
command to a read or write command. If your system installs good quality of
SDRAM, you can set this option to “3 SCLKs” to obtain better memory performance.
Normally, the option will be set to Auto.
The choice: 2, 3, 4, 5, 6, and Auto.
DRAM RAS# Precharge
This option controls the number of SCLKs for RAS# precharge. If your system installs
good quality of SDRAM, you can set this option to “3 SCLKs” to obtain better
memory performance. It is set to auto normally.
The choice: 2, 3, 4, 5, 6, and Auto.
Precharge delay (tRAS)
The choice: 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, and 15, Auto.
System Memory Frequency
Users are recommended to use Auto for memory frequency selection.
The choice: 400MHz, 533MHz, and Auto.
SLP_S4# Assertion Width
The choice: 4 to 5 Sec., 3 to 4 Sec, 2 to 3 Sec., 1 to 2 Sec.
System BIOS Cacheable
Selecting Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh,
resulting in better system performance. However, if any program writes to this
memory area, a system error may result.
The choice: Enabled, Disabled.
Video BIOS Cacheable
Select “Enabled” to enable caching VGA BIOS into L2 cache to get higher display
performance. “Disabled” to ignore this BIOS caching function.
The choice: Enabled, Disabled.
Memory Hole At 15M-16M
In order to improve performance, certain space in memory is reserved for ISA cards.
This memory must be mapped into the memory space below 16MB.
The choice: Enabled, Disabled.
WADE-8071 User’s Manual
4-12
BIOS Setup Information
PCI Express Root Port Func
PCI Express Port 1-4
The choice: Auto, Enabled and Disabled.
PCI-E Compliancy Mode
The choice: v1.0a, v1.0.
On-Chip Frame Buffer Size
Users can set the display memory size that shared from main memory.
The choice: 1MB, 8MB.
DVMT Mode
The choice: FIXED, DVMT, BOTH
DVMT/FIXED Memory Size
The choice: 64MB, 128MB, 224MB.
Boot Display
The choice: CRT, LVDS, CRT+LVDS.
WADE-8071 User’s Manual
4-13
BIOS Setup Information
Panel Type
The choice: 800x600 18bits 1ch, 1024x768 18bits 1ch, 1280x1024 24bits 2ch, 1600x1200
18bits 2ch.
LAN1(J5) /LAN2(J6) Enable/Disable Control
The choice: Enabled, Disabled.
4.7
Integrated Peripherals
WADE-8071 User’s Manual
4-14
BIOS Setup Information
IDE HDD Block Mode
If your IDE hard drive supports block mode select Enabled for automatic detection of
the optimal number of block read/writes per sector the drive can support.
The choice: Enabled, Disabled.
IDE DMA transfer access
The choice: Enabled, Disabled.
On-Chip Primary/ Secondary PCI IDE
The chipset contains a PCI IDE interface with support for two IDE channels. Select
Enabled to activate the primary IDE interface. Select Disabled to deactivate this
interface.
The choice: Enabled, Disabled
IDE Primary/Secondary Master/Slave PIO
The four IDE PIO (Programmed Input/Output) fields allow set a PIO mode (0-4) for
each of the four IDE devices that the onboard IDE interface supports. Modes 0
through 4 provide successively increased performance. In Auto mode, the system
automatically determines the best mode for each device.
The choice: Auto, Mode 0, Mode 1, Mode 2, Mode 3, Mode 4.
WADE-8071 User’s Manual
4-15
BIOS Setup Information
IDE Primary/Secondary Master/Slave UDMA
Ultra DMA/33/66/100 implementation is possible only if IDE hard drive supports
and the operating environment includes a DMA driver (Windows 95 OSR2 or a
third-party IDE bus master driver). If your hard drive and system software both
support Ultra DMA/33/66/100, select Auto to enable BIOS support.
The choice: Auto, Disabled.
SATA Mode
The choice: IDE, AHCI.
On-Chip Serial ATA
[Disabled]: Disabled SATA Controller. [Auto]: Auto arrange by BIOS. [Combined
Mode]: PATA and SATA are combined. Max. of 2 IDE drives in each channel.
[Enhanced Mode]: Enable both SATA and PATA. Max. of 6 IDE drives are supported.
[SATA only]: SATA is operating in legacy mode.
The choice: Disabled, Auto, Combined Mode, Enhanced Mode, SATA Only.
SATA PORT Speed Setting
The choice: Disabled, Force GEN I, Force GEN II.
PATA IDE Mode
This field is used to select the function mode of the IDE connector.
Secondary
Slave channel. SATA 1 and SATA 2 serve as Primary Master and
Primary Slave channel.
SATA Port
If the “PATA IDE Mode” field is set to Secondary, this field will show “P0, P2 is
Primary”; meaning SATA 1 and SATA 3 are Primary.
WADE-8071 User’s Manual
4-16
BIOS Setup Information
SuperIO Device
Onboard Serial Port 1
Select an address and corresponding interrupt for the first serial ports.
The choice: Disabled, 3F8, 2F8, 3E8, 2E8, 208, 218.
Serial Port 1 Use IRQ
The choice: IRQ3, IRQ4, IRQ10, IRQ 5.
Onboard Serial Port 2
Select an address and corresponding interrupt for the second serial ports.
The choice: Disabled, 3F8, 2F8, 3E8, 2E8, 208, 218.
Serial Port 2 Use IRQ
The choice: IRQ3, IRQ4, IRQ10, IRQ 5.
UART Mode Select
This item allows users to select Infrared transmission mode.
Normal
IrDA
ASKIR
Disable Infrared function
Select IrDA mode transmission
Select ASKIR mode transmission
WADE-8071 User’s Manual
4-17
BIOS Setup Information
※RxD ,TxD Active
This item is to configure Infrared transmission rate. Four options are available:
Hi, Hi
Hi, Lo
Lo, Hi
Lo, Lo
High rate for receiving /High rate for transmitting
High rate for receiving /Low rate for transmitting
Low rate for receiving /High rate for transmitting
Low rate for receiving /Low rate for transmitting
※IR Transmission Delay
This option will be available when IR is enabled.
The choice: Enabled, Disabled.
※UR2 Duplex Mode
The available choices are full duplex mode and half duplex mode.
The choice: Full, Half.
※Use IR Pins
The available choices are IR-Rx2Tx2, RxD2, and TxD2.
The choice: IR-Rx2Tx2, RxD2, TxD2.
Onboard Serial Port 3
Allows you to manual select an I/O address for the onboard serial port 3.
The Choice: Disabled, 3F8, 2F8, 3E8, 2E8, 208, 218.
Serial Port 3 Use IRQ
Allows you manually select an IRQ for the onboard serial port 3.
The choice: IRQ3, IRQ4, IRQ10, IRQ 5.
Onboard Serial Port 4
Allows you manually select an I/O address for the onboard serial port 4.
The choice: Disabled, 3F8, 2F8, 3E8, 2E8, 208, 218.
Serial Port 4 Use IRQ
Allows you manually select an IRQ for the onboard serial port 4.
The choice: IRQ3, IRQ4, IRQ10, IRQ 5.
WADE-8071 User’s Manual
4-18
BIOS Setup Information
Onboard Parallel Port
This item allows you to configuring I/O address of the onboard parallel port.
The choice: Disabled, 378/IRQ7, 278/IRQ5, 3BC/IRQ7.
Parallel Port Mode
There are six different modes for the onboard parallel port.
The choice: Standard, EPP 1.9+SPP, ECP, ECP+EPP1.9, Printer, EPP1.7+SSP, and
ECP+EPP1.7
ECP Mode Use DMA
Select a proper DMA channel for ECP mode.
The choice: 3, 1.
Watch Dog Timer Select
This BIOS testing option is able to reset the system according to the selected table.
The choice: Disabled, 10 Sec, 20 Sec, 30 Sec, 40 Sec, 1 Min, 2 Min, and 4 Min.
PWRON After PWR-Fail
This item allows user to configure the power status of using ATX power supply after
a serious power loss occurs.
The choice: Off, On, Former-Sts
WADE-8071 User’s Manual
4-19
BIOS Setup Information
USB Device Setting
USB 1.0 Controller
[Enabled] or [Disabled] Universal host controller interface for universal serial bus.
The choice: Enabled, Disabled.
USB 2.0 Controller
[Enabled] or [Disabled] Enhanced host controller interface for universal serial bus.
The choice: Enabled, Disabled.
USB Operation Mode
Auto decides USB device operation mode. [High speed]: If USB device was high
speed device, then it operated on high speed mode. If USB device was full/low speed
device, then it operated on full/low speed mode; [Full/Low speed]: All of USB
device operated on Full/Low speed mode.
The choice: High Speed, Full/Low Speed.
USB Keyboard/Mouse Function
[Enabled] or [Disabled] Legacy support of USB keyboard or mouse.
The choice: Disabled, Enabled.
WADE-8071 User’s Manual
4-20
BIOS Setup Information
USB Storage Function
[Enabled] or [Disabled] Legacy support of USB Mass Storage.
4.8
Power Management Setup
The Power Management Setup allows configuration of the system to most effectively
save energy while operating in a manner consistent with your own style of computer
use.
ACPI Function
This item allows you to enable/disable the Advanced Configuration and Power
Management (ACPI).
The choice: Enabled, Disabled.
ACPI Suspend Type
To decide which ACPI suspend mode to use.
The choice: S1 (POS), S3 (STR).
WADE-8071 User’s Manual
4-21
BIOS Setup Information
Run VGA BIOS if S3 Resume
The choice: Auto, Yes, No.
Power Management
This category allows selecting the type (or degree) of power saving and is directly
related to “HDD Power Down”, “Suspend Mode”.
There are three selections for Power Management, three of which have fixed mode
settings.
Min Saving
Max Saving
User Define
Minimum power management. Suspend Mode = 1 Hour,
and HDD Power Down = 15 Min.
Maximum power management. Suspend Mode = 1 Min.,
and HDD Power Down = 1 Min.
Allows you to set each mode individually. When not
disabled, Suspend Mode ranges from 1 min. to 1 Hour and
HDD Power Down ranges from 1 Min. to 15 Min.
Video off Method
This determines the manner in which the monitor is blanked.
V/H SYNC+Blank
Blank Screen
DPMS
This selection will cause the system to turn off the vertical
and horizontal synchronization ports and write blanks to
the video buffer.
This option only writes blanks to the video buffer.
Initial display power management signaling.
Video Off In Suspend
This allows user to enable/disable video off in Suspend Mode.
The choice: Yes, No.
Suspend Type
Two options are available: Stop Grant and PwrOn Suspend.
The choice: Stop Grant, PwrOn Suspend.
MODEM Use IRQ
The choice: NA, 3,4 ,5 ,7 ,9 ,10 ,11.
WADE-8071 User’s Manual
4-22
BIOS Setup Information
Suspend Mode
When enabled and after the set time of system inactivity, all devices except the CPU
will be shut off.
The choice: Disabled, 1 Min, 2 Min, 4 Min, 8 Min, 12 Min, 20 Min, 30 Min, 40 Min, and
1 Hour.
HDD Power Down
When enabled and after the set time of system inactivity, the hard disk drive will be
powered down while all other devices remain active.
The choice: Disabled, 1 Min, 2 Min, 3 Min, 4 Min, 5 Min, 6 Min, 7 Min, 8 Min, 9 Min, 10
Min, 11 Min, 12 Min, 13 Min, 14 Min, 15 Min.
Soft-Off by PWR-BTTN
This item allows users to set the time to remove the power after the power button is
pressed.
The choice: Instant-Off, Delay 4 Sec.
Wake Up By Onboard LAN
The choice: Disabled, Enabled.
Power On by Ring
When “Enabled” selected, a system at soft-off mode will be alert to Wake-On-Modem
signal.
The choice: Enabled, Disabled.
USB KB Wake-Up From S3
The choice: Enabled, Disabled.
Resume by Alarm
This item allows users to enable/disable the resume by alarm function. When
“Enabled” is selected, system using ATX power supply could be powered on if a
customized time and day is approached.
The choice: Enabled, Disabled.
※Date(of Month) Alarm
When “Resume by Alarm” is enabled, this item could allow users to configure the
date parameter of the timing dateline on which to power on the system.
The choice: 0 ~ 31.
WADE-8071 User’s Manual
4-23
BIOS Setup Information
※Time (hh:mm:ss) Alarm
When “Resume by Alarm” is enabled, this item could allow users to configure the
time parameter of the timing dateline on which to power on the system.
The choice: hh (0~23), mm (0~59), ss (0 ~59).
Primary/Secondary IDE 0/1
This item is to configure IDE devices being monitored by system so as to keep system
out of suspend mode if the associated device is busy.
The choice: Enabled, Disabled.
FDD, COM, LPT Port
This item is to configure floppy device, COM ports, and parallel port being monitored
by system so as to keep system out of suspend mode if the associated device is busy.
The choice: Enabled, Disabled.
PCI PIRQ[A-D]#
The choice: Enabled, Disabled.
WADE-8071 User’s Manual
4-24
BIOS Setup Information
4.9
PnP/PCI Configurations
This section describes configuring the PCI bus system. PCI, or Personal Computer
Interconnect, is a system which allows I/O devices to operate at speeds nearing the
speed the CPU itself uses when communicating with its own special components.
This section covers some very technical items and it is strongly recommended that
only experienced users should make any changes to the default settings.
Init Display First
The choice: PCI Slot, Onboard, PCIEx.
Reset Configuration Data
Default is Disabled. Select Enabled to reset Extended System Configuration Data
(ESCD) when you exit Setup if you have installed a new add-on and the system
reconfiguration has caused such a serious conflict that the OS cannot boot.
The choice: Enabled, Disabled.
Resource Controlled By
BIOS can automatically configure all the boot and plug and play compatible devices.
If you choose Auto, you cannot select IRQ DMA and memory base address fields,
since BIOS automatically assigns them.
The choice: Auto (ESCD), Manual.
WADE-8071 User’s Manual
4-25
BIOS Setup Information
※IRQ Resources
Legacy ISA for devices compliant with the original PC AT bus specification, PCI/ISA
PnP for devices compliant with the Plug and Play standard whether designed for PCI
or ISA bus architecture.
The choice: Press Enter.
IRQ-3/IRQ-4/IRQ-5/IRQ-7/IRQ-9/IRQ-10/IRQ-11/IRQ-12/IRQ-14/IRQ-15
assigned to.
The choice: PCI Device, Reserved.
PCI/VGA Palette Snoop
The choice: Enabled, Disabled.
Maximum Payload Size
Set maximum TLP payload size for the PCI Express devices. The unit is byte.
The choice: 128, 256, 512, 1024, 2048, 4096.
4.10
PC Health Status
WADE-8071 User’s Manual
4-26
BIOS Setup Information
CaseOpen# Warning
The choices: Disabled, Enabled.
CPU Warning Temperature
This item allows you to set a temperature above which the system will start the
beeping warning. Default setting is disabled. This function will only with “ACPI”
power management and “S3 (STR)” suspends type.
The choices: Disabled, 50℃/122℉, 53℃/127℉, 56℃/133℉, 60℃/140℉, 63℃/145
℉, 66℃/151℉, 70℃/158℉.
CPU Fan Smart Fan Temp
The choices: Disabled, 35℃/95℉, 45℃/113℉, 55℃/131℉.
Fan Tolerance Value
The choices: 1, 2, 3, 4, 5.
4.11
Frequency/Voltage Control
Auto Detect PCI Clk
The choice: Enabled, Disabled.
WADE-8071 User’s Manual
4-27
BIOS Setup Information
Spread Spectrum
This item allows user to enable/disable the spread spectrum modulate.
The choice: Enabled, Disabled.
CPU Host/SRC/PCI Clock
The choice:
Default, 100/100/33MHz, 133/100/33Mhz, 166/100/33MHz, 200/100/33Mhz,
266/100/33MHz.
4.12
Default Menu
Selecting “Defaults” from the main menu shows two options which are described
below,
WADE-8071 User’s Manual
4-28
BIOS Setup Information
Load Fail-Safe Defaults
When <Enter> is pressed, a confirmation dialog box with a message similar to:
Load Fail-Safe Defaults (Y/N) ? N
Pressing ‘Y’ loads the BIOS default values for the most stable, minimal-performance
system operations.
Load Optimized Defaults
When <Enter> is pressed, a confirmation dialog box with a message similar to:
Load Optimized Defaults (Y/N) ? N
Pressing ‘Y’ loads the default values that are factory settings for optimal performance
system operations.
WADE-8071 User’s Manual
4-29
BIOS Setup Information
4.13
Supervisor/User Password Setting
Either supervisor or user password can be setup, or both of then. The differences
between are:
Set Supervisor Password : can enter and change the options of the setup menus.
WADE-8071 User’s Manual
4-30
BIOS Setup Information
Set User Password : just can only enter but do not have the right to change the
options of the setup menus. When selecting this function, the following message will
appear at the center of the screen to assist you in creating a password.
ENTER PASSWORD
Type the password, up to eight characters in length, and press <Enter>. The
password typed now will clear any previously entered password from CMOS
memory. You will be asked to confirm the password. Type the password again and
press <Enter>. You may also press <Esc> to abort the selection and not enter a
password.
To disable a password, just press <Enter> when prompted to enter the password. A
message will confirm the password will be disabled. Once the password is disabled,
the system will reboot and Setup can be entered freely.
PASSWORD DISABLED
When a password has been enabled, user will be prompted to enter it every time user
tries to enter Setup. This prevents an unauthorized person from changing any part of
your system configuration.
Additionally, when a password is enabled, you can also require the BIOS to request a
password every time your system is rebooted. This would prevent unauthorized use
of the computer.
User may determine when the password is required within the BIOS Features Setup
Menu and its Security option (see Section 3). If the Security option is set to “System”,
the password will be required both at boot and at entry to Setup. If set to “Setup”,
prompting only occurs when trying to enter Setup.
WADE-8071 User’s Manual
4-31
BIOS Setup Information
4.14
Exiting Selection
WADE-8071 User’s Manual
4-32
BIOS Setup Information
Save & Exit Setup
Pressing <Enter> on this item asks for confirmation:
Save to CMOS and EXIT (Y/N)? Y
Pressing “Y” stores the selections made in the menus in CMOS – a special section of
memory that stays on after system off. During subsequent booting of computer, the
BIOS configure the system according to the Setup selections stored in CMOS. After
saving the values the system is restarted again.
Exit Without Saving
Pressing <Enter> on this item asks for confirmation:
Quit Without Saving (Y/N)? N
This allows user to exit Setup without storing in CMOS any change. The previous
selections remain in effect. This exits the Setup utility and restarts your computer.
WADE-8071 User’s Manual
4-33
Troubleshooting
Chapter 5
Troubleshooting
This chapter provides a few useful tips to quickly get WADE-8072 running with
success. As basic hardware installation has been addressed in Chapter 2, this chapter
will primarily focus on system integration issues, in terms of BIOS setting, and OS
diagnostics.
5.1
Hardware Quick Installation
ATX Power Setting
WADE-8072 supports ATX only. Therefore, there is no other setting that really needs
to be set up. However, there are only one connector that must be connected—J26 (20
pins Power Connector). Portwell wants to provide customer better performance and
more reliable system. By using this CPU Supplementary will enhance the power
drawing to the motherboard.
Serial ATA and IDE Hard Disk Setting
Unlike IDE bus, each Serial ATA channel can only connect to one SATA hard disk at a
time; there are total two connectors, J20 and J21. The installation of Serial ATA is
simpler and easier than IDE, because SATA hard disk doesn’t require setting up
Master and Slave, which can reduce mistake of hardware installation.
WADE-8071 User’s Manual
5-1
Troubleshooting
5.2
BIOS Setting
It is assumed that users have correctly adopted modules and connected all the
devices cables required before turning on power. 200-pin DDR2 SDRAM, keyboard,
mouse, SATA hard disk, VGA connector, device power cables, ATX accessories are
good examples that deserve attention. With no assurance of properly and correctly
accommodating these modules and devices, it is very possible to encounter system
failures that result in malfunction of any device.
To make sure that you have a successful start with WADE-8072, it is recommended,
when going with the boot-up sequence, to hit “DEL” key and enter the BIOS setup
menu to tune up a stable BIOS configuration so that you can wake up your system far
well.
Loading the default optimal setting
When prompted with the main setup menu, please scroll down to “Load Optimized
Defaults”, press “Enter” and “Y” to load in default optimal BIOS setup. This will
force your BIOS setting back to the initial factory configuration. It is recommended to
do this so you can be sure the system is running with the BIOS setting that Portwell
has highly endorsed. As a matter of fact, users can load the default BIOS setting any
time when system appears to be unstable in boot up sequence.
Auto Detect Hard Disks
In the BIOS => Standard CMOS setup menu, pick up any one from
Primary/Secondary Master/Slave IDE ports, and press “Enter”. Setup the selected
IDE port and its access mode to “Auto”. This will force system to automatically pick
up the IDE devices that are being connected each time system boots up.
Improper disable operation
There are too many occasions where users disable a certain device/feature in one
application through BIOS setting. These variables may not be set back to the original
values when needed. These devices/features will certainly fail to be detected.
When the above conditions happen, it is strongly recommended to check the BIOS
settings. Make sure certain items are set as they should be. These include the COM1/
COM2 ports, USB ports, external cache, on-board VGA and Ethernet.
It is also very common that users would like to disable a certain device/port to
release IRQ resource. A few good examples are
Disable COM1 serial port to release IRQ #4
Disable COM2 serial port to release IRQ #3
Etc…
WADE-8071 User’s Manual
5-2
Troubleshooting
A quick review of the basic IRQ mapping is given below for your reference.
IRQ#
IRQ #0
IRQ #1
IRQ #2
IRQ #3
IRQ #4
IRQ #5
IRQ #6
IRQ #7
IRQ #8
IRQ #9
IRQ #10
IRQ #11
IRQ #12
IRQ #13
IRQ #14
IRQ #15
Description
System Timer
Keyboard Event
Usable IRQ
COM2
COM1
Usable IRQ
Diskette Event
Usable IRQ
Real-Time Clock
Usable IRQ
Usable IRQ
Usable IRQ
IBM Mouse Event
Coprocessor Error
Hard Disk Event
Usable IRQ
It is then very easy to find out which IRQ resource is ready for additional peripherals.
If IRQ resource is not enough, please disable some devices listed above to release
further IRQ numbers.
5.3
FAQ
Symptom: SBC keeps beeping, and no screen has shown.
Solution: In fact, each beep sound represents different definition of error message.
Please refer to table as following:
Beep sounds
One long beep with one
short beeps
One long beep constantly
One long beep with two
short beeps
Beep rapidly
Meaning
DRAM error
Action
Change DRAM or reinstall it
DRAM error
Monitor or Display
Card error
Power error warning
Change DRAM or reinstall it
Please check Monitor connector
whether it inserts properly
Please check Power mode setting
Information & Support
Question: I forget my password of system BIOS, what am I supposed to do?
Answer: You can simply short 2-3 pins on JP7 to clean your password.
WADE-8071 User’s Manual
5-3
Troubleshooting
Note:
Please visit our technical web site at
http://www.portwell.com.tw
For additional technical information, which is not covered in this manual, you can
mail to [email protected] or you can also send mail to our sales, they will be
very delighted to forward them to us.
WADE-8071 User’s Manual
5-4
Appendix A
System Memory Address Map
Each On-board device in the system is assigned a set of memory addresses, which
also can be identical of the device. The following table lists the system memory
address used for your reference.
Memory Area
0000-003F
0040-004F
0050-006F
0070-0E2E
0E2F-0F6B
0F6C-9EFF
9F00-9FBF
9FC0-9FFF
A000-AFFF
B000-B7FF
B800-BFFF
C000-CEBF
CEC0-EFFF
F000-FFFF
WADE-8071 User’s Manual
Size
Device Description
1K
Interrupt Area
0.3K
BIOS Data Area
0.5K
System Data
54K
DOS
5K
Program Area
574K
[Available]
= Conventional memory ends at 640K =
3K
Extended BIOS Area
1K
Unused
64K
VGA Graphics
32K
Unused
32K
VGA Text
59K
Video ROM
133K
Unused
64K
System ROM
Appendix B
Interrupt Request Lines (IRQ)
Peripheral devices can use interrupt request lines to notify CPU for the service
required. The following table shows the IRQ used by the devices on board.
IRQ#
IRQ 0
IRQ 1
IRQ 2
IRQ 3
IRQ 4
IRQ 5
IRQ 6
IRQ 7
IRQ 8
IRQ 9
IRQ 10
IRQ 11
IRQ 12
IRQ 13
IRQ 14
IRQ 15
Current Use
System ROM
System ROM
[Unassigned]
System ROM
System ROM
[Unassigned]
System ROM
[Unassigned]
System ROM
[Unassigned]
[Unassigned]
[Unassigned]
System ROM
System ROM
System ROM
[Unassigned]
WADE-8071 User’s Manual
Default Use
System Timer
Keyboard Event
Usable IRQ
COM2
COM1
Usable IRQ
Diskette Event
Usable IRQ
Real-Time Clock
Usable IRQ
Usable IRQ
Usable IRQ
IBM Mouse Event
Coprocessor Error
Hard Disk Event
Usable IRQ
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement