Modway EEI-4246-GRY-WHI Prestige 24" Bathroom Vanity Assembly Instructions

Thank you for purchasing the MODWAY Vanity!

Before you start, here are some helpful advice:

1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.

2.Owing to the size and weight of the vanity, we recommend that it is assembled by two adults, on a carpeted or

padded area, in the room that it is intended for. Approximate assembly time: 60 minutes.

3.Please do not use any tools other than those provide or recommended in these instructions.

4.Please do not throw away any of the packaging or instructions until you have checked all the components and

hardware and the furniture is fully assembled.

5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the

components from time to time, so please save the tools that have been provided.

6.Please keep all pieces out of reach of children.

Carefully insert the Wood Dowels (A) at the designated holes on the relevant parts.

Hardware required. Hammer not included

(Power tool not recommended)

Use Philips screwdriver to insert the Cambolt (B) carefully at the designated holes on the relevant parts.

Please ensure the Cambolt is inserted and secured at the correct pre-drilled holes.

Hardware required. Screwdriver not included

Secure the Door Stopper (K) to the Bottom Panel (3) with Screw (J) .

Hardware required. Screwdriver not included

Secure the Vertical Panel 1 (8) to the Side Panel Left (1) and Side Panel Right (2) with

16 pieces of Screws (L) .

Hardware required. Screwdriver not included

Assemble 2 pieces of Door Hinges (G) to the 'Door Left (9)' and 'Door Right (10)' on each sides and secure it with 2 pieces of Screws (F) for each hinges.

Hardware required. Screwdriver not included

6.1- Secure the Horizontal Panel (13) to the Base Panel 1 (4) with 2 pieces of Screws (L) .

6.2- Use screwdriver to secure the Metal Bracket (H) to the Horizontal Panel (13) with

2 pieces of Screws (F) .

Hardware required. Screwdriver not included

Properly insert the Camlock (C) in the pre-drilled hole then align it to the assembled Cambolt (B) to secure both Side Panel Left (1) to the Vertical Panel 2 (11) and Vertical Panel 3 (12) .

This assembly namely Side Frame Assembly

Hardware required. Screwdriver not included

8.1- Lay flat the Side Panel Left (1) which already assembled with 4 pieces of Cambolt (B) .

8.2- Insert Camlock (C) to the pre-drilled hole of the Bottom Panel (3) then properly align the Wooden

Dowel to the pre-drilled hole of the Side Panel Left (1) .

8.3- Once aligned and attached, make sure to secure Camlock (C) from the Bottom Panel (3) to the

Cambolt (B) of the Side Panel Left (1) .

8.4- Repeat steps to secure the Base Panel 1 (4) , Base Panel 2 (5) and Back Panel 7 to

the Side Panel Left (1) as shown.

Hardware required. Screwdriver not included

Make sure the Adjustable Shelf (6) with Wood Dowel was attached to the Vertical Panel 2 (11) .

Secure a Screw (L) to the Adjustable Shelf (6) thru the Vertical Panel (11&12) by using screwdriver as shown.

Properly insert the Camlock (C) in the pre-drilled hole then align it to the assembled Cambolt (B) to secure

Side Panel Right (2) to the Vertical Panel 2 (11) and Vertical Panel 3 (12) .

This assembly namely Side Frame Assembly

Hardware required. Screwdriver not included

Repeat steps from STEP 8.2 -8.3 to secure Bottom Panel (3) , Base Panel 1 (4) , Base Panel 2 (5) ,

Back Panel (7) and Adjustable Shelf (6) as shown.

Hardware required. Screwdriver not included

Carefully turnover the assembled vanity from STEP 11. Secure a Screw (L) on each side of the

Adjustable Shelf (6) thru the Vertical Panel (11&12) by using screwdriver as shown.

Hardware required. Screwdriver not included

Hardware required. Screwdriver not included

Assemble Door Knob (D) on each 'Door Left (9)' and 'Door Right (10)' and secure it with a Screw (E) by using screwdriver.

Hardware required. Screwdriver not included

Use Screwdriver to secure the Metal Bracket (I) on each corner of the top portion of the Vanity Cabinet with 4 pieces of Screw (F) .

Hardware required. Screwdriver not included

Note: Professional work required.

Hole=Ø6mm

Screw and Wall Plug are not provided.

Please use appropriate fixtures for your wall.