EN_EW7733UND_UM_v1.0 28Mayo2012

EN_EW7733UND_UM_v1.0 28Mayo2012

Wireless 450N Dual Band USB Adapter

User Manual

Version: 1.0

(May, 2012)

COPYRIGHT

Copyright ©2005/2006 by this company. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company

This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, this company reserves the right to revise this publication and to make changes from time to time in the contents thereof without obligation to notify any person of such revision or changes.

C A T A L O G

CHAPTER I: Product Information................................................................. 4

1-1 Introduction and safety information. ........................................................... 4

1-2 Safety Information. ........................................................................................ 5

1-3 System Requirements. ................................................................................... 6

CHAPTER II: Driver Installation and Configuration ............................... 8

2-1 Network Card Installation. ............................................................................ 8

2-2 Connect to Wireless Access Point. ................................................................ 14

2-2-1 Using Movistar USB Wireless Adapter. ..................................................... 14

2-2-2 Using Windows Zero Configuration (Windows XP Only). ....................... 18

2-3 Connection Profile Management ................................................................... 22

2-3-1 Add a new entry.......................................................................................... 22

2-3-2 Remove an existing profile ........................................................................ 25

2-3-3 Edit an existing profile ............................................................................... 26

2-3-4 WPS Profile Setup ...................................................................................... 27

2-3-4-1 PBC mode WPS configuration. .............................................................. 29

2-3-4-2 PIN mode WPS configuration. ............................................................... 30

2-4 View Link Status ............................................................................................ 32

2-5 Advanced Settings ......................................................................................... 34

2-5-1 Advanced menu. ......................................................................................... 34

2-6 About ............................................................................................................. 36

CHAPTER III: Appendix ........................................................................... 37

3-1 Hardware Specification ................................................................................. 37

3-2 Troubleshooting ............................................................................................. 38

4-4 FCC and Other Compliance Statements ........................................................ 43

CHAPTER I: Product Information

1-1 Introduction and safety information.

Thank you for purchasing this extreme high-speed 802.11a/b/g/n dual band wireless network card! Excepting common wireless standards

802.11a/b/g, this wireless network card is also 802.11n compatible - data transfer rate is 450Mbps, and that’s night times faster than 802.11g wireless network! 802.11n also provides wider wireless coverage, so you don’t have to worry if your computer is far from your wireless access point.

With easy-to-install USB 2.0 interface - a very common expansion port of computers - plug this wireless network card into any empty USB port of your computer, just that simple!

Other features of this product including:

Portable dongle type design.

Supports Infrastructure, Ad-Hoc, and Wi-Fi Direct connection method.

QoS function: provides Wi-Fi Multimedia (WMM) quality of service to secure audio/video/voice data traffic as higher priority.

802.11a/b/g/n compatible.

Supports major encryption methods like WEP, WPA, and WPA2 encryption.

WPS configuration - You don’t need an experienced computer technician to help you to get connected. With WPS, you can get your computer connected by simply pushing a button on USB network card or entering an 8-digit code.

USB 2.0 interface - you can get it installed on your computer in just few seconds!

Wireless access control - prevent unauthorized network access to your network and computer.

1-2 Safety Information.

In order to keep the safety of users and your properties, please follow the following safety instructions:

1. This USB wireless network card is designed for indoor use only. DO

NOT expose this network card to direct sun light, rain, or snow.

2. DO NOT put this network card at or near hot or humid places, like kitchen or bathroom. Also, do not left this wireless network card in the car in summer.

3. This network card is small enough to put in a child’s mouth, and it could cause serious injury or could be fatal. If they throw the network card, the card will be damaged. PLEASE KEEP THIS NETWORK

CARD OUT THE REACH OF CHILDREN!

4. This network card will become hot when being used for long time

(This is normal and is not a malfunction). DO NOT put the network card on a paper, cloth, or other flammable objects after the network card has been used for a long time.

5. There’s no user-serviceable part inside the network card. If you found that the network card is not working properly, please contact your dealer of purchase and ask for help. DO NOT disassemble the network card by yourself, warranty will be void.

6. If the network card falls into water, DO NOT USE IT AGAIN

BEFORE YOU SEND THE CARD TO THE DEALER OF PURCHASE

FOR INSPECTION.

7. If you smell something strange or even see some smoke coming out from the network card, switch the computer off immediately, and call dealer of purchase for help.

1-3 System Requirements.

An empty USB 2.0 port (May not be able work with USB 1.1 port, and performance will be greatly reduced)

Windows XP, Vista, or Windows 7 operating system

CD-ROM drive

At least 100MB of available disk space

1-4 Package Contents.

Before you starting to use this wireless network card, please check if there’s anything missing in the package, and contact your dealer of purchase to claim for missing items:

USB wireless network card (1 pcs) ……………………………… 1

Cradle (1 pcs) ………………….………………………………….2

Quick installation guide (1 pcs) ………………………………….. 3

Driver/Utility/User Manual CD-ROM (1 pcs) …………………… 4

Warranty card (1 pcs) …………………………………………...... 5

1-5 Familiar with your new wireless network card.

1.

USB Connector

2.

External Wireless Antenna

3.

Link/Activity LED

4.

WPS Button (Press to activate WPS pairing mode)

1

3

4

2

LED Name Light Status Description

Link/

Activity

Blinking

Off

Linked to a wireless access point /

Transferring data

Power off

CHAPTER II: Driver Installation and Configuration

2-1 Network Card Installation.

Please follow the following instructions to install your new wireless network card:

1.

Insert the USB wireless network card into an empty USB 2.0 port of your computer when computer is switched on. Never use force to insert the card, if you feel it’s stuck, flip the card over and try again.

2.

Insert device driver CDROM into the CD/DVD ROM drive of your computer, and execute ‘AutoRun.exe’ program in ‘Driver’ folder.

3.

On Windows Vista / Windows 7 computer, Movistar USB Wireless

Adapter Utility will start, click ‘Install Drivers and Utility’ to continue.

4.

Please select the Location you want to install the Utility, and then click ‘Siguiente’.

5.

Select ‘Program file’ and click ‘Continue’.

6.

Utility setup will start. Please be patient while installation is in progress, this may require few minutes.

7.

Click ‘Finish’ to finish installation procedure.

8.

Please insert your USB wifi network card to any empty USB port now.

A popup message indicating that your computer found ‘802.11n USB

Wireless LAN Card’ will appear. Please be patient while Windows is installation driver.

This message will only appear when you insert the USB wifi network card to your computer’s USB port, or you insert the network card to a different USB port of your computer.

9.

You should be able to see this popup message, indicating your new

USB network is ready to use; If not, please either try to re-install driver, or insert the network card to another USB port of your computer.

10.

A new icon will appear near the clock of system tray:

Left-click the icon will launch wireless network configuration utility, and you can right-click the icon to show the quick menu of

configuration utility.

This icon uses 3 colors to represent current network status:

Network connection established.

Network connection is not yet established.

Network card not found on your computer.

For detailed instructions of wireless network configuration utility, please refer to next chapter.

2-2 Connect to Wireless Access Point.

To use wireless network, you have to connect to a wireless access point first. You can either use “Movistar USB Wireless Adapter” (comes with network card driver), or Windows Zero Configuration Utility (comes with

Windows operating system).

2-2-1 Using Movistar USB Wireless Adapter.

Please follow the following instructions to use Ralink configuration utility to connect to wireless access point.

1.

Left-click the “Movistar USB Wireless Adapter” configuration utility icon located at lower-right corner of computer desktop, and configuration menu will appear:

2.

Wireless utility will appear.

“Redes Disponibles” section will list the available wireless networks (and their status). When the Utility is launched it will automatically go to this section.

There are 7 fields in Site Survey list:

Field Description

Nombre de Red. The Service-Set IDentifier of network device

(The name of network device)

Banda. The Wi-Fi band the network is using (2,4Ghz or

5Ghz).

Canal

Wireless mode

The channel number of this network device

Available wireless mode.

802.11a wireless capability

802.11b wireless capability

802.11g wireless capability

802.11n wireless capability

Seguridad

Señal

Security mode. When nothing is displayed here, means this network device does not require security and anyone can connect to it.

Shows the wireless signal strength in percentage.

Higher percentage means better signal quality.

3.

To connect to a wireless access point, double click on it:

Calidad de Señal Shows the wireless signal strength in a graphical way.

4.

If the wireless access point you wish to connect does not appear here, you can click ‘Actualizar’ button to scan for wireless access points again. If the wireless access point you’re looking for still not appear, try to move the computer closer.

5.

You’ll be prompted to introduce Wireless Network Password (if any),

(key or passphrase, depends on encryption method):

Click “Siguiente” to continue. If you introduce a wrong password, connection will not be able to establish.

6.

Network card will attempt to connect to access point now, this may require few seconds to minutes, please be patient. When you see there’s a check shown beside the access point you wish to connect, your computer is connected to access point you selected. The connection status will be displayed in configuration utility also.

(see example picture below).

Movistar USB Wireless adapter Utility will prompt you a success window:

2-2-2 Using Windows Zero Configuration (Windows XP Only).

Windows XP and Vista and has a built-in wireless network configuration utility, called as ‘Windows Zero Configuration’ (WZC). You can also use

WZC to configure your wireless network parameter:

1.

Right-click configuration utility’s icon, and select ‘Use Zero

Configuration as Configuration Utility’.

In this mode, you can still use Ralink configuration utility to check the connection status, but unable to connect to a wireless network, or change network setting.

Follow the following steps to use WZC to establish network connection. If you wish to return to use Ralink configuration utility again, right-click Ralink configuration utility icon again, and select

‘Use RaConfig as Configuration Utility’.

2.

Click ‘Start’ button (should be located at the bottom-left corner of windows desktop), click ‘Control Panel’, then click ‘Network and

Internet Connections’ in Control Panel.

3.

Click ‘Connect to a network’ under ‘Network Connections’.

4.

Right-click ‘Wireless Network Connection’ (it may have a number as suffix if you have more than one wireless network card, please make sure you right-click the ‘802.11n Wireless LAN Card), then select

‘View Available Wireless Networks’.

5.

All wireless access points in proximity will be displayed here. If the access point you want to use is not displayed here, please try to move your computer closer to the access point, or you can click ‘Refresh network list’ to rescan access points. Click the access point you want to use if it’s shown, then click ‘Connect’.

6.

If the access point is protected by encryption, you have to input its security key or passphrase here. It must match the encryption setting on the access point.

If the access point you selected does not use encryption, you’ll not be prompted for security key or passphrase.

7.

If you can see ‘Connected’ message, the connection between your computer and wireless access point is successfully established.

2-3 Connection Profile Management

For connections you’ll frequently use, you can save them as a profile and you can recall all settings (security type, password, etc.) back soon.

2-3-1 Add a new entry

By this function you can setup the connection parameters for a specific wireless access point in advance, so you can recall a set of connection parameters quickly.

To do this, follow the following procedures:

1.

Click ‘Gestion Perfiles’ in configuration utility, Profile manager will appear:

2.

Click “Añadir” to add a new profile.

3.

Please name the profile in ‘Nombre Perfil’ field, and select the AP you wish to connect in ‘Nombre Red’ dropdown list. Select Authentication and Encryption Method. Introduce Wi-Fi password Key in “Clave

Seguridad” (If required).

4.

The profile will be saved in the list:

You can repeat step 2 to 4 to setup more profiles of wireless connections. When you wish to connect to a certain wireless access point, Select a Profile and click on ‘Conectar’ button (as indicated above).

A check mark will be displayed beside active profile.

2-3-2 Remove an existing profile

When you no longer need an existing profile, just select it from the list and click ‘Borrar’ button.

If the profile you wish to delete is active now, you’ll be prompted to confirm deletion:

To delete anyway, click “Aceptar”.

2-3-3 Edit an existing profile

If you have added a profile before, and you wish to change the content of the profile, you can use this function. Please select a profile from the list first, then click ‘Editar’ button.

You’ll be provided with the contents of selected profile; you can edit them and save changes.

2-3-4 WPS Profile Setup

WPS (Wi-Fi Protected Setup) is a new, convenient way to setup secured wireless connections. You only need to push a button or input a set of

8-digit random number, and you can setup a secure connection between wireless devices, like what a professional wireless expert can do.

To use WPS profile, you have to make sure the access point you wish to connect supports WPS first. You can discover if an access point is

WPS-capable or not by site-survey:

In this list, there are access points that support WPS, which are indicated by icon.

You can still establish secured connection with WPS-capable access points in conventional way. To establish WPS-style connection, select the

Network and click ‘Siguiente’ button:

You’ll be prompted to select WPS, select “Si” and Click on “ Siguiente”

Button:

You’ll be prompted to select WPS method and WPS AP.

To use PIN (8-digit or 4-digit random number) to setup WPS, select ‘PIN

/ numeric code’, and you have to select an AP from ‘WPS AP List’ dropdown menu; to establish connection by Push-Button Configuration

(PBC), you don’t have to select an AP from ‘WPS AP List’ dropdown list.

Note: This device follows WPS 2.0 Standard Specification to allow inputting 4-digit PIN code, pls. make sure your Wireless Router or

Access Point supports WPS 2.0 accordingly, or use 8-digit PIN as usual.

2-3-4-1 PBC mode WPS configuration.

When you want to use ‘PBC’ mode, Select “Botón” as indicated in previous image.

Please push the WPS button on the access point (a physical button or a

Software button in its configuration menu,Please refer to access point’s user manual) within 2 minutes.

Click ‘Aplicar’ button:

Please be patient. You’ll be prompted when WPS connection is established successfully; if you received an error, you can try again.

2-3-4-2 PIN mode WPS configuration.

There are two roles in PIN mode WPS configuration: “Dinamico” and

“Registro”. “Registro” is the one who waits for incoming WPS request, and “Enrollee” is the one who searches for WPS registrar and will attempt to connect it.

The WPS role of two devices should not be same: When one device is

Registro, the other one must be “Dinamico”, and vice versa.

To setup WPS connection by PIN, select “PIN”

There will be a menu displaying 8-digit WPS PIN code on the configuration menu, please get this number. Please remember the number will become invalid after a short period of time (2 minutes or so).

Select ‘Registro’ in ‘Configuration mode’ dropdown list, and input PIN code in ‘Pin Code’.

Click ‘Aplicar’ to begin WPS connection, please be patient. You’ll be prompted when WPS connection is established successfully; if you received an error, you can try again, but please remember to make sure the PIN you obtained from access point is still valid.

2-4 View Link Status

You can check the status of active wireless connection by clicking Link

Information button, a new window will appear:

There are 3 kinds of link information: a.

Link Status “Información Conexión Establecida”:

Displays the status of Network Speed and Quality of the Link.

b.

USB dongle information:

Displays the Interface status information and MAC address of the dongle:

IF you click on “Desactivar” you will disable the interface. c.

IPv4 or IPv6 address information:

Displays the values of Network Parameters IP address , Subnet Mask,

Default Gateway and DNS for IPv4 and IPv6.

2-5 Advanced Settings

Click ‘Opciones Avanzadas’ button at Profile Management to show advanced configuration menu. In this menu, you can configure some advanced wireless settings.

Normally you don’t need to change these settings to establish wireless connection. Only change these settings when you know what you’re doing and you really need these changes.

2-5-1 Advanced menu.

You can configure Static IPv4 and IPv6 Settings in this section.

Choose IPv4 submenu and select “Usar la siguiente dirección IP” to manually configure your IPv4 Settings:

Choose IPv6 submenu and select “Usar la siguiente dirección IP” to manually configure your IPv6 Settings:

2-6 About

Click this button to see the version information of software configuration utility.

CHAPTER III: Appendix

3-1 Hardware Specification

Standards: IEEE 802.11a/b/g/n

Interface: USB 2.0 (USB 1.1 Compatible)

Frequency Band: 2.4000 ~ 2.4835GHz (Industrial Scientific

Medical Band)

5.1500 ~ 5.8250GHz (subject to local regulations)

Data Rate: 11b: 1/2/5.5/11Mbps

11g: 6/9/12/24/36/48/54Mbps

11n (20MHz): MCS0-23 (up to 216Mbps)

11n (40MHz): MCS0-23 (up to 450Mbps)

Securities: WEP 64/128, WPA, WPA2

802.1x Support

Antenna: Internal Antenna plus external antenna (3T3R, MIMO technology)

Drivers: Windows 2000/XP/Vista/7

LED: Link/Activity

Dimension: 27.2(H) x 17.2(W) x 87.1(D) mm

Temperature: 32~104°F (0 ~ 40°C)

Humidity: 10-95% (NonCondensing)

Certification: FCC, CE

3-2 Troubleshooting

If you encounter any problem when you’re using this wireless network card, don’t panic! Before you call your dealer of purchase for help, please check this troubleshooting table, the solution of your problem could be very simple, and you can solve the problem by yourself!

Scenario

I can’t find any wireless access point / wireless device in ‘Site Survey’ function.

Nothing happens when I click ‘Launch config utilities’

I cannot establish connection with a certain wireless access point

Solution

1.

Click ‘Rescan’ for few more times and see if you can find any wireless access point or wireless device.

2.

Please move closer to any known wireless access point.

3.

Please adjust the position of network card (you may have to move your computer if you’re using a notebook computer) and click ‘Rescan’ button for few more times. If you can find the wireless access point or wireless device you want to connect by doing this, try to move closer to the place where the wireless access point or wireless device is located.

1.

Please make sure the wireless network card is inserted into your computer’s

USB port. If the configuration utility’s icon is black, the network card is not detected by your computer.

2.

Reboot the computer and try again.

3.

Remove the card and insert it into another USB port.

4.

Remove the driver and re-install.

5.

Contact the dealer of purchase for help.

1. Click ‘Connect’ for few more times.

2. If the SSID of access point you wish to connect is hidden (nothing displayed in

The network is slow / having problem when transferring large files

‘SSID’ field in ‘Site Survey’ function), you have to input correct SSID of the access point you wish to connect. Please contact the owner of access point to ask for correct SSID.

3. You have to input correct passphrase / security key to connect an access point with encryption. Please contact the owner of access point to ask for correct passphrase / security key.

4. The access point you wish to connect only allows network cards with specific

MAC address to establish connection.

Please go to ‘About’ tab and write the value of ‘Phy_Addess’ down, then present this value to the owner of access point so he / she can add the MAC address of your network card to his / her access point’s list.

1.

Move closer to the place where access point is located.

2.

Enable ‘Wireless Protection’ in

‘Advanced’ tab.

3.

Try a lower TX Rate in ‘Advanced’ tab.

4.

Disable ‘Tx Burst’ in ‘Advanced’ tab.

5.

Enable ‘WMM’ in ‘QoS’ tab if you need to use multimedia / telephony related applications.

6.

Disable ‘WMM – Power Save Enable’ in

‘QoS’ tab.

7.

There could be too much people using the same radio channel. Ask the owner of the access point to change the channel number.

Please try one or more solutions listed above.

3-3 Glossary

1.

What is the IEEE 802.11g standard?

802.11g is the new IEEE standard for high-speed wireless LAN communications that provides for up to 54 Mbps data rate in the 2.4

GHz band. 802.11g is quickly becoming the next mainstream wireless LAN technology for the home, office and public networks.

802.11g defines the use of the same OFDM modulation technique specified in IEEE 802.11a for the 5 GHz frequency band and applies it in the same 2.4 GHz frequency band as IEEE 802.11b. The

802.11g standard requires backward compatibility with 802.11b.

The standard specifically calls for:

A.

A new physical layer for the 802.11 Medium Access Control

(MAC) in the 2.4 GHz frequency band, known as the extended rate PHY (ERP). The ERP adds OFDM as a mandatory new coding scheme for 6, 12 and 24 Mbps (mandatory speeds), and 18,

36, 48 and 54 Mbps (optional speeds). The ERP includes the modulation schemes found in 802.11b including CCK for 11 and

5.5 Mbps and Barker code modulation for 2 and 1 Mbps.

B.

A protection mechanism called RTS/CTS that governs how

802.11g devices and 802.11b devices interoperate.

2.

What is the IEEE 802.11b standard?

The IEEE 802.11b Wireless LAN standard subcommittee, which formulates the standard for the industry. The objective is to enable wireless LAN hardware from different manufactures to communicate.

3.

What does IEEE 802.11 feature support?

The product supports the following IEEE 802.11 functions:

4.

What is Ad-hoc?

An Ad-hoc integrated wireless LAN is a group of computers, each has a Wireless LAN card, Connected as an independent wireless

LAN. Ad hoc wireless LAN is applicable at a departmental scale for a branch or SOHO operation.

CSMA/CA plus Acknowledge Protocol

Multi-Channel Roaming

Automatic Rate Selection

RTS/CTS Feature

Fragmentation

Power Management

5.

What is Infrastructure?

An integrated wireless and wireless and wired LAN is called an

Infrastructure configuration. Infrastructure is applicable to enterprise scale for wireless access to central database, or wireless application for mobile workers.

6.

What is BSS ID?

A specific Ad hoc LAN is called a Basic Service Set (BSS).

Computers in a BSS must be configured with the same BSS ID.

7.

What is WEP?

WEP is Wired Equivalent Privacy, a data privacy mechanism based on a 40 bit shared key algorithm, as described in the IEEE 802 .11 standard.

8.

What is TKIP?

TKIP is a quick-fix method to quickly overcome the inherent weaknesses in WEP security, especially the reuse of encryption keys.

TKIP is involved in the IEEE 802.11i WLAN security standard, and the specification might be officially released by early 2003.

9.

What is AES?

AES (Advanced Encryption Standard), a chip-based security, has been developed to ensure the highest degree of security and authenticity for digital information, wherever and however communicated or stored, while making more efficient use of hardware and/or software than previous encryption standards. It is also included in IEEE 802.11i standard. Compare with AES, TKIP is a temporary protocol for replacing WEP security until manufacturers implement AES at the hardware level.

10.

Can Wireless products support printer sharing?

Wireless products perform the same function as LAN products.

Therefore, Wireless products can work with Netware, Windows

2000, or other LAN operating systems to support printer or file sharing.

11.

Would the information be intercepted while transmitting on air?

WLAN features two-fold protection in security. On the hardware side, as with Direct Sequence Spread Spectrum technology, it has the inherent security feature of scrambling. On the software side,

WLAN series offer the encryption function (WEP) to enhance security and Access Control. Users can set it up depending upon their needs.

12.

What is DSSS? What is FHSS? And what are their differences?

Frequency-hopping spread-spectrum (FHSS) uses a narrowband carrier that changes frequency in a pattern that is known to both transmitter and receiver. Properly synchronized, the net effect is to maintain a single logical channel. To an unintended receiver, FHSS appears to be short-duration impulse noise. Direct-sequence spread-spectrum (DSSS) generates a redundant bit pattern for each bit to be transmitted. This bit pattern is called a chip (or chipping code). The longer the chip is, the greater the probability that the original data can be recovered. Even if one or more bits in the chip are damaged during transmission, statistical techniques embedded in the radio can recover the original data without-the need for retransmission. To an unintended receiver, DSSS appears as low power wideband noise and is rejected (ignored) by most narrowband receivers.

13.

What is Spread Spectrum?

Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communication systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade off produces a signal that is, in effect, louder and thus easier to detect, provided that the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread –spectrum signal looks like background noise. There are two main alternatives,

Direct Sequence Spread Spectrum (DSSS) and Frequency Hopping

Spread Spectrum (FHSS).

14.

What is WPS?

WPS stands for Wi-Fi Protected Setup. It provides a simple way to establish unencrypted or encrypted connections between wireless clients and access point automatically. User can press a software or hardware button to activate WPS function, and WPS-compatible wireless clients and access point will establish connection by themselves. There are two types of WPS: PBC (Push-Button

Configuration) and PIN code.

4-4 FCC and Other Compliance Statements

Federal Communication Commission

Interference Statement

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4. Consult the dealer or an experienced radio technician for help.

FCC Caution

This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment.

Federal Communication Commission (FCC) Radiation Exposure

Statement

This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the

FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.

The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE 1999/5/EC

OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE)

The R&TTE Directive repeals and replaces in the directive 98/13/EEC

(Telecommunications Terminal Equipment and Satellite Earth Station

Equipment) As of April 8, 2000.

Safety

This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.

EU Countries Intended for Use

The ETSI version of this device is intended for home and office use in Austria,

Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy,

Luxembourg, the Netherlands, Portugal, Spain, Sweden, and the United

Kingdom.

The ETSI version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and Switzerland.

EU Countries Not intended for use

None.

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project