ESIM364

ESIM364

GSM ALARM AND MANAGEMENT SYSTEM USER MANUAL

ESIM364

User Manual v1.2

Valid for ESIM364 v02.04.01 and up

Safety instructions

Please read and follow these safety guidelines in order to maintain safety of operators and people around: • GSM alarm & management system ESIM364 (also referenced as alarm system, system or device) has radio transceiver operat­ ing in GSM 850/900/1800/1900 bands. • DO NOT use the system where it can be interfere with other devices and cause any potential danger. • DO NOT use the system with medical devices. • DO NOT use the system in hazardous environment. • DO NOT expose the system to high humidity, chemical environment or mechanical impacts. • DO NOT attempt to personally repair the system. • System label is on the bottom side of the device. GSM alarm system ESIM364 is a device mounted in limited access areas. Any system repairs must be done only by quali­ fied, safety aware personnel.

The system must be powered by main 16-24V 50 Hz ~1.5A max or 18-24V be approved by LST EN 60950-1 standard and be easily accessible nearby the device. When connecting the power supply to the system, switching the pole terminals places does not have any affect.

1,5A max DC power supply which must Any additional devices linked to the system ESIM364 (computer, sensors, relays etc.) must be approved by LST EN 60950-1 standard.

Main power supply can be connected to AC mains only inside installation room with automatic 2-pole circuit breaker capable of disconnecting circuit in the event of short circuit or over-current condition. Open circuit breaker must have a gap between con­ nections of more than 3mm and the disconnection current 5A. Phase Null PE AC/DC AC 230V 50 Hz/DC 24V USB cable

ESIM364

Mains power and backup battery must be disconnected before any installation or tuning work starts. The system installa­ tion or maintenance must not be done during stormy conditions.

Backup battery must be connected via the connection which in the case of breaking would result in disconnection of one of battery pole terminals. Special care must be taken when connecting positive and negative battery terminals. Switching the pole terminals places is NOT allowed.

In order to avoid fire or explosion hazards the system must be used only with approved backup battery.

The device is fully turned off by disconnecting 2-pole switch off device of the main power supply and disconnecting backup battery connector. Fuse F1 type – Slow Blown 3A. Replacement fuses have to be exactly the same as indicated by the manufacturer.

If you use I security class computer for setting the parameters it must be connected to earth.

The WEEE (Waste Electrical and Electronic Equipment) marking on this product (see left) or its documentation indicates that the product must not be disposed of together with household waste. To prevent possible harm to human health and/or the environ­ ment, the product must be disposed on in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the system supplier, or the local authority responsible for waste disposal in your area.

Limited Liability

The buyer must agree that the system will reduce the risk of fire, theft, burglary or other dangers but does not guarantee against such events. “ELDES UAB” will not take any responsibility re­ garding personal or property or revenue loss while using the system. “ELDES UAB” liability ac­ cording to local laws does not exceed value of the purchased system. “ELDES UAB” is not affiliated with any of the cellular providers therefore is not responsible for the quality of cellular service.

Manufacturer Warranty

The system carries a 24-month warranty by the manufacturer “ELDES UAB”. Warranty period starts from the day the system has been purchased by the end user. The warranty is valid only if the system has been used as intended, following all guidelines listed in the manual and within speci­ fied operating conditions. Receipt must be kept as a proof of purchase date.

The warranty is voided if the system has been exposed to mechanical impact, chemicals, high humidity, fluids, corrosive and hazardous environ­ ments or other force majeure factors.

Technical Support

If you require more detailed information on your system or in case of system failure occurrence, please, contact your alarm system installer.

About User Manual

This document describes basic configuration and usage of alarm system ESIM364. It is very impor­ tant to read the user manual before starting to use the system.

Package Content

1. ESIM364............... ..................................... qty. 1 2. Microphone.................. ..............................qty.1 3. SMA antenna......... ...................................qty. 2 4. Buzzer........................... ............................. qty. 1 5. Back-up battery connection wire... ...... qty. 1 6. User manual....................... ....................... qty. 1 7. Resistors 5,6kΩ......................... .............qty. 12 8. Resistors 3,3kΩ................. .......................qty. 6 9. Plastic standoffs................ ......................qty. 4 NOTE: For complete system configuration and control, please refer to ESIM364 installation manual located at www.eldes.lt/en/download

Contents

1. General Information ..................................................................... 4

1.1 Short Description of Main Definitions ...............................................4

1.2 EKB2 Keypad Overview ...........................................................................5

1.3 EKB3/EKB3W Keypad Overview ...........................................................7

1.4 Partitions ......................................................................................................7

2. Technical Specifications ............................................................... 8

2.1 Electrical & Mechanical Characteristics .............................................8

2.2 Main Unit, LED & Connector Functionality ......................................9

2.3 Wiring Diagrams .....................................................................................10

2.3.1 General Wiring .........................................................................10

2.3.2 Zone Connection Types ........................................................10

3. Basic Configuration & Use ..........................................................11

3.1 Setting Up Date & Time ........................................................................11

3.2. Arming, Disarming the System & Turning Off the Alarm .........12

3.2.1 Arm, Disarm & Turn off the Alarm by Phone Call .........12

3.2.2 Arm by SMS text message ...................................................13

3.2.3 Disarm & Turn off the Alarm by SMS text message ....13

3.2.4 Arm by EKB2 Keypad .............................................................14

3.2.5 Disarm & Turn off the Alarm by EKB2 Keypad ..............14

3.2.6 Arm by EKB3/EKB3W Keypad .............................................15

3.2.7 Disarm & Turn off the Alarm by EKB3/EKBW Keypad .15

3.2.8 Arm by iButton® Key ..............................................................16

3.2.9 Disarm & Turn off the Alarm by iButton® Key ...............16

3.2.10 Arm by EWK1 – Wireless Key-fob .......................................17

3.2.11 Disarm & Turn off the Alarm by EWK1 – Wireless Key-fob ...................................18

3.3 Activating STAY Mode ..........................................................................19

3.3.1 Arm by EKB2 Keypad in STAY Mode Manually ..............19

3.4 Alarm Indications & Viewing Violated Zones / Tampers ...........21

3.5 Bypassing & Activating Zones ...........................................................22

3.6 Viewing System Information ..............................................................23

3.7 Managing Periodical System Information .....................................23

3.8 Viewing Zone & PGM Output Information ....................................24

3.9 Managing Temperature Information ..............................................25

3.10 Indication of System Faults .................................................................26

3.11 Controlling Electrical Appliances .....................................................28

3.12 Turning ON/OFF the Electrical Appliances for a Determined Time Period ....................................29

4. If the Alarm System is Connected to Monitoring Station ........30

Copyright © “ELDES UAB”, 2013. All rights reserved It is not allowed to copy and distribute information in this document or pass to a third party without advanced written authorization by “ELDES UAB”. “ELDES UAB” reserves the right to update or modify this document and/or related products without a warning. Hereby, “ELDES UAB” declares that this GSM alarm and management system ESIM364 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at www.eldes.lt

4

1. General Information

ESIM364 is an alarm system for private houses, cottages, village houses, garages, warehouses and other buildings, also capable of turning on/off the electrical appliances by SMS text message and alarm system keypad. This alarm system provides a simple thus effective way of use. The system may consist of: • ESIM364 alarm system device.

• Up to 4 EKB2/EKB3 wired keypads.

• Up to 4 EKB3W wireless keypads.

• Wired and/or wireless detection devices: movement sensors, magnetic door contacts, smoke sensors etc.

• Other devices: indoor/outdoor sirens, zone/PGM output expansion modules, heating, lighting, gates etc.

For more details on ESIM364 system, please, consult with your alarm system installer.

1.1 Short Description of Main Definitions

The following table provides the explanation of main definitions which are met in this user manual.

Definition

System; alarm system SMS Keypad EKB2 EKB3 EKB3W EWK1 EWK2 User phone number; User 1... 10 System phone number User password iButton® key Zone PGM output Partition

Description

ESIM364 device Short Message Service text Device with a set keys allowing to configure & control the system, view violated zones & system faults Model of wired LCD keypad Model of wired LED keypad Model of wireless LED keypad Model of wireless keyfob Model of wireless keyfob Phone number of the user allowed to control and receive SMS text messages from the system Phone number of the SIM card inserted in ESIM364 device 4-digit combination intended for system arming/disarming using a keypad Microchip containing a unique 64-bit ID code intended for system arming/disarming Alarm system input for wired and wireless sensor connection Alarm system output for connection of electrical appliances (heating, lighting, gates etc.) Section dividing one alarm system into two or more independent parts software-wise

1.2 EKB2 Keypad Overview

EKB2 is an LCD keypad intended for using with ESIM364 alarm system.

Keys Functionality

...

One menu level back / cancel Menu navigation – up Menu navigation – down Confirm (enter) value Value typing Keypad partition switch / minus symbol for entering negative temp. value Additional menu / minus symbol for entering negative temp. value GSM Signal Strength System Status Message System Fault Indi­ cation Custom Keypad Partition Title Temperature STAY BYP FLT 20,2 0 C ready GARAGE 00:45 Digital Clock Home Screen View Bypass Mode Indication Stay Mode Indication

Fig. No. 1

Main Messages & Icons Icon / Message Description

Delay zone violated when system is disarmed.

Exit delay countdown initiated.

System is armed and menu is locked.

System is disarmed and menu is unlocked

+ CONFIGURATION MODE BURGLARY ALARM

Configuration Mode activated.

Delay, Instant or Follow zone violated when system is armed.

Icon / Message 24 ALARM FIRE ALARM TAMPER ALARM READY NOT READY ARMED STAY BYP FLT Description

24H zone violated.

Fire zone violated.

Tamper violated System is ready to be armed.

System is not ready to be armed – one or more zones / tampers violated.

System is armed (optional feature).

Stay mode activated One or more zones bypassed One or more system faults are present MANUAL ELDES ESIM364 V1.2 5

EKB2 LCD screen is intended for displaying alarm system status messages and alerts. Message READY is displayed on the screen that no zones and/or tampers are violated and the system is prepared for arming. Message NOT READY (and FLT) shows up in case of zone violation or if system faults are present. The alarm system cannot be armed until the faults are removed or violated zone (-s) is restored, bypassed or set up to operate under Force mode. The following faults allow system arming when present: • • • • • • • • • main power supply is lost.

low battery.

battery dead or missing.

battery failed.

siren failed.

GSM jammer detected.

date/time not set.

GSM connection failed.

GSM antenna failed.

Audio Indication

The built-in buzzer uses two types of sound signals – three short beeps and one long beep. Three short beeps stand for successfully carried out configuration command, one long beep – for invalid configuration command. In addition, the buzzer emits short beeps in case of alarm.

Visual Indication

EKB2 can be used even in dark premises as the LCD screen and keys are illuminated continuously. The illumination level lowers down if 3 minutes after the last key-touch expires while the system is disarmed. In case of alarm, the keypad illumination level is boosted and stays in this state until the system is disarmed. 6

1.3 EKB3/EKB3W Keypad Overview

EKB3/EKB3W is a LED keypad intended for using with ESIM364 alarm system.

LED Functionality

ARMED READY SYSTEM BYPS 1­12 Alarm system is armed /Configuration mode System is prepared for arming Steady ON - system faults / flashing - violated high numbered zone Zone bypass mode Violated zone ARMED READY SYSTEM 1 5 6 4 3 2 A B 11 12 9 10 BYPS 7 8 1 4 7 * 2 5 8 0

Fig. No. 2

Keys Functionality

[BYPS] [CODE] [*] [#] [0] ... [9] [STAY] [INST] Zone bypass mode Additional options - system fault list / violated high zone indication / violated tamper indication Cancel command / keypad partition switch (if enabled) Confirm (enter) command Command typing Manual Stay mode activation (currently inactive) 9 # 3 6 STAY BYPS INST CODE The green indicator READY indicates that no zones and/or tampers are violated and the system is prepared for arming. Yellow indica­ tor SYSTEM lights up or flashes in case of zone violation or if system faults are present. The alarm system cannot be armed until the faults are removed or violated zone (-s) is restored, bypassed or set up to operate under Force mode. The following faults allow system arming when present: • • • • • • • • • main power supply is lost.

low battery.

battery dead or missing.

battery failed.

siren failed.

GSM jammer detected.

date/time not set.

GSM connection failed.

GSM antenna failed.

Audio Indication

The built-in buzzer uses two types of sound signals – three short beeps and one long beep. Three short beeps stand for successfully carried out configuration command, one long beep – for invalid configuration command. In addition, the buzzer emits short beeps in case of alarm.

Visual Indication

EKB3 keys have a LED back-light, therefore it is possible to use this keypad even in dark premises. The back-light lasts for 3 minutes after the last key-stroke while the system is disarmed. In case of alarm, the keypad back-light turns ON and lasts until the system is disarmed. EKB3W keys have a LED back-light, which will be activated once any key is pressed. Due to battery power saving reasons, the back light and LED light last for 10 seconds after the last key-stroke.

1.4 Partitions

Your alarm system may be divided into up to 4 partitions: Partition 1 - Partition 4 . Each system partition operates independently from each other, therefore dividing the system into partitions allows to use 1 alarm system unit to secure up to 4 different areas, for example: office and warehouse, house and garage etc. By default configuration, the system is NOT divided into partitions and all user phone numbers, user passwords, keypads, iButton® keys, zones are assigned to Partition 1.

MANUAL ELDES ESIM364 V1.2 7

8

2. Technical Specifications 2.1 Electrical & Mechanical Characteristics

Electrical & Mechanical Characteristics

Main Power Supply Current in Standby without External Sensors and Keypad Recommended Backup Battery Voltage, Capacity Recommended Backup Battery Type Maximum Battery Charge Current GSM Modem Frequency Cable Type for GSM Antenna Connection Number of Zones on Board Nominal Zone Resistance Number of PGM Outputs on Board On-board PGM Output Circuit Maximum Commuting On-board PGM Output Values BELL: Siren Output when Activated BELL: Maximum Siren Output Current BELL: Maximum Cable Length for Siren Connection BELL: Cable Type for Siren Connection AUX: Auxiliary Equipment Power Supply Voltage AUX: Maximum Accumulative Current of Auxiliary Equipment AUX: Maximum Cable Length for Auxiliary Equipment Connection AUX: Cable Type for Auxiliary Equipment Connection BUZ: Maximum Current of Mini Buzzer BUZ: Power Supply Voltage of Mini Buzzer BUZ: Cable Type for Mini Buzzer Connection Supported Temperature Sensor Model Maximum Supported Number of Temperature Sensors DATA: Maximum Cable Length for 1-Wire® Communication DATA: Cable Type for 1-Wire® Communication Supported iButton® Key Model Maximum Supported Number of Keypads Y/G: Maximum Cable Length for RS485 Communication Y/G: Cable Type for RS485 Communication MIC: Maximum Cable Length for Microphone Connection MIC: Cable Type for Microphone Connection Wireless Transmitter-Receiver Frequency Wireless Communication Range Maximum Supported Number of Wireless Devices Event Log Size Maximum Supported Number of Zones Maximum Supported Number of PGM Outputs Cable Type for Zone and PGM Output Connection Communications Supported Protocols Dimensions Operating Temperature Range Humidity 16-24V 50 Hz ~1.5A max / 18-24V Up to 80mA 12V; 1,3-7Ah Lead-Acid 900mA 850/900/1800/1900MHz Shielded 6 (ATZ mode: 12) 5,6kΩ (ATZ Mode: 5,6kΩ and 3,3kΩ) 4 1,5A max 1 R OUT Open Collector Output. Output is pulled to COM when turned ON.

4 x Voltage – 30V; current – 500mA.

Connected to COM 1A Up to 100 meters Unshielded 13,8V DC 1,1A Up to 100 meters Unshielded 150mA 5V DC Unshielded Maxim®/Dallas® DS18S20, DS18B20 8 Up to 30 meters Unshielded Maxim®/Dallas® DS1990A 4 x EKB2 / EKB3 Up to 100 meters Unshielded Up to 2 meters Unshielded 868 Mhz Up to 30m in premises; up to 150m in open areas 32 500 events 76 76 Unshielded SMS, Voice calls, GPRS network, RS485, CSD, PSTN Ademco Contact ID, EGR100, Kronos, Cortex SMS 140x100x18mm ­20...+55 0 C 0-90% RH @ 0... +40 °C (non-condensing)

2.2 Main Unit, LED & Connector Functionality

Main Unit Functionality

GSM MODEM GSM network 850/900/1800/1900MHz modem SIM CARD1 Primary SIM card slot / holder SIM CARD2 DEF USB Secondary SIM card slot / holder Pins for restoring default settings Mini USB port FUSE F1 W-LESS ANT GSM ANT 3A fuse Wireless antenna SMA type connector GSM antenna SMA type connector MODULES* Slots for EA1, EA2 or EPGM8 module USB W-LESS ANT DEF PRG

LED Functionality

NETW GSM network signal strength C1 PGM output C1 status - on/off C2 C3 PGM output C2 status - on/off PGM output C3 status - on/off C4 STAT PGM output C4 status - on/off Micro-controller status

Connector Functionality

TIP* PSTN (landline) terminal RING* PSTN (landline) terminal DATA +5V 1-Wire® interface for iButton key & temperature sensor connection Temperature sensor power supply terminal (+5V) MIC MIC+ BUZ­ BUZ+ C1 - C4 Z1 ­ Z6 Y G COM BELL­ Microphone negative terminal Microphone positive terminal Buzzer negative terminal Buzzer positive terminal PGM output terminals Security zone terminals RS485 interface for communication (yellow wire) RS485 interface for communication (yellow wire) Common return terminal Siren negative terminal BELL+ AUX­ AUX+ AC/DC AKU­ Siren positive terminal Negative power supply terminal for auxiliary equipment Positive power supply terminal for auxiliary equipment Main power supply terminals Backup battery negative terminal AKU+ Backup battery positive terminal * - Optional, implementable on request in advance Z1 CO Z2 Z3 CO Fig. No.3

SIM CARD1 SIM CARD2 GSM ANT G S M MO DE M MODULES BELL- BELL+ AKU+ AKU MANUAL ELDES ESIM364 V1.2 9

2.3 Wiring Diagrams

2.3.1 General Wiring

Z1 CO Z2 Z3 CO BELL- BELL+ AKU+ AKU Backup Battery 12V 1.3-7Ah Metal cabinet PE terminal Z1 Z2 Fig. No. 2 ~16-24V Fuse 500 mA ~230V 50Hz Z5 Z6 BUZ MIC SIREN/BELL 1A max.

EPGM1 iButton® key reader Temperature sensor SIREN/BELL 1A max.

BLACK 3,3kΩ 3,3kΩ RED + Fig. No. 3 BELL- BELL+ SIREN/BELL 1A max.

BLACK RED + Relay module BELL- BELL+ EKB3 EKB2

Siren status monitoring

By default, the system monitors siren status and indicates system fault on the keypad if the siren is broken/discon­ nected. However, this feature requires a pair of parallelly connected resistors of 3,3kΩ nominal across BELL+ and BELL- terminals.

No siren status monitoring

If the siren status monitoring feature is not required, do not connect any resistor in parallel and disable siren fault indication on the keypad (see 3.10 Indication of System Faults).

Fig. No. 4

2.3.2 Zone Connection Types Type 1 Type 2 Type 3 Type 4 Type 5

10 Normally open contact with 5,6KΩ end of line resistor Normally closed con­ tact with 5,6KΩ end of line resistor Tamper and 5,6KΩ end of line resistor and 3,3KΩ end of line resistor with normally closed contact ATZ Mode: 5,6KΩ end of line resistor and nor­ mally closed contact with 3,3KΩ end of line resistor and normally closed contact ATZ Mode: Tamper, 5,6KΩ end of line resistor, 5,6KΩ end of line resistor with nor­ mally closed contact and 3,3KΩ end of line resistor with normally closed contact. Fig. No. 4

3. Basic Configuration & Use

ATTENTION: System configuration described in this chapter is based on default system parameter values. Your alarm system installer may have changed those values. For more details, please, contact your alarm system installer.

This chapter provides a description of basic configuration and use of ESIM364 alarm system by the following methods: • SMS text message. • Phone call. • EKB2 keypad. • EKB3 keypad. • EKB3W wireless keypad. • iButton® key.

• EWK1 wireless keyfob.

• EWK2 wireless keyfob

SMS

In order to configure and control the system using SMS text message, send the text command to the ESIM364 system phone number from one of the preset user phone numbers. In this user manual the underscore symbol ”_” represents one space character. Every underscore symbol must be re placed by a single space character. There must be no spaces or other unnecesary characters at the beginning and at the end of the message. ssss – 4­digit SMS password set by your alarm system installer.

EKB2 EKB3/ EKB3W

The system configuration and control by EKB2 keypad is performed by navigating throughout the menu section list dis­ played on LCD screen. To navigate in the menu path, touch go one menu section back by touching ↓, ↑ keys to select the desired menu section and touch OK key to open the selected section. To enter a required value, use 0... 9 keys and touch OK key for value confirmation or cancel/ ←key. The value can be typed in directly by touching 0... 9 keys while highlighting the desired menu section. EKB2 menu type is “circle”, therefore when the last section in the menu list is selected, you will be brought back to the beginning of the list after touching the ↓ key. In this user manual, the menu path is provided under “tree” view by starting at home screen view. In this user manual valid parameter range is indicated in brackets.. The system configuration and control by EKB3/EKB3W keypad is carried out by entering a valid configu ration command using the number keys [0]... [9], [#] key for confirmation and [*] key to cancel the characters that are being entered. Al­ ternatively, the user can wait for 10 seconds until the keypad buzzer will provide a long beep indicating that the entered characters have been cancelled. When typing in the characters, the indication of each pressed key is provided by short beep of keypad buzzer. Additionalty, the red indicators light up when the number keys [0]... [9] are being pressed. Some commands require [BYPS], [CODE] and [STAY] keys as well. The structure of a standard con figuration command is a com­ bination of digits. The variables are provided in lower-case letters, while a valid parameter value range is provided in brackets.

NOTE: If you have accidentally typed in the * as the first character, please press [*] key again or wait for 10 seconds until the keypad buzzer will provide a long beep indicating that the typed in characters have been cancelled.

3.1 Setting Up Date & Time

NOTE: When the alarm system is connected to a monitoring station the date and time are set automatically. The system retrie­ ves this data from the monitoring station by itself.

SMS

1. Send the following SMS text message to the phone number of ESIM364 alarm system:

SMS text message content:

ssss_yyyy.mm.dd_hr:mn Value: yyyy – year; mm – month, range – [01... 12]; dd – day, range - [01... 31]; hr – hours, range – [00... 23], mn – minutes, range – [00... 59].

Example: 1111_2011.12.15_13:45 2. The system will reply with confirmation by SMS text message to user phone number who sent the SMS text message after the date & time is set successfully.

MANUAL ELDES ESIM364 V1.2 11

EKB2

Navigate through the following menu path using OK and arrow keys and enter the date and time values using the number keys:

Menu path:

OK → DATE/TIME SET → OK → yyyy-mm-dd_hr:mn → OK Value: yyyy – year; mm – month, range – [01... 12]; dd – day, range - [01... 31]; hr – hours, range – [00... 23], mn – minutes, range – [00... 59].

Example: 2011-12-15 13:45

3.2. Arming, Disarming the System & Turning Off the Alarm

Before arming the system it is necessary to close all doors and windows in the secured area and move yourself away from the move­ ment detection field.

Don’t stand in movement sensor detection zone Close all doors Close all windows

3.2.1 Arm, Disarm & Turn off the Alarm by Phone Call

ATTENTION: User must leave the secured area before arming the system by phone call.

Close all doors

Fig. No. 7

1. To arm, disarm the system & turn off the alarm, make a phone call to the system‘s phone number from any of 10 available user phone numbers. The phone call is free charge as the system rejects it and carries out arming/disar­ ming procedure after-wards. When arming – the system rejects the phone call after 2 rings, when disarming – the system rejects the phone call immediately. 2. The system will initiate the entry delay countdown (by default – 15 seconds) after the user has entered the secured area. Entry delay countdown is intended for user to disarm the system before the alarm is caused. The countdown is indicated by long steady beep emit ted by buzzer connected to the alarm system (if any).

3. When the system is successfully armed or disarmed, it will reply with confirmation by SMS text message to the user phone number that made a phone call.

CALL SMS User ESIM364

Fig. No. 8

4. When attempting to arm the system in case of violated zone / tamper presence, the system will not permit to arm it and it will reply with violated zone / tamper number to the user phone number that made a phone call. For more details on how to arm the system in case of violated zones presence, please refer to 3.5 Bypassing & Activating Zones.

12

3.2.2 Arm by SMS text message SMS

1. Leave the secured area.

2. To arm the system, send the following SMS text message to the system‘s phone number from any out of 10 preset user phone numbers:

SMS text message content:

ssss_ARMp or ssss_ARMp,p,p,p Example: 1111_ARM1 Value: p - partition number, range - [1... 4] 3. When the system is successfully armed, it will reply with confirmation by SMS text message to the user phone number that sent the SMS text message.

SMS SMS User ESIM364

Fig. No. 9

4. When attempting to arm the system in case of violated zone / tamper presence, the system not permit to arm it and it will reply with violated zone / tamper number to the user phone number that sent the SMS text message. For more details on how to arm the system in case of violated zones presence, please refer to 3.5 Bypassing & Activating Zones.

3.2.3 Disarm & Turn off the Alarm by SMS text message SMS

1. The system will initiate the entry delay countdown (by default – 15 seconds) after the user has entered the secured area. Entry delay countdown is intended for user to disarm the system before the alarm is caused. The countdown is indicated by long steady beep emitted by buzzer connected to the alarm system (if any).

2. To disarm the system or turn off the alarm, send the following SMS text message to the system‘s phone number from any out of 10 preset user phone numbers:

SMS text message content:

ssss_DISARMp or ssss_DISARMp,p,p,p Example: 1111_DISARM1,3,4 Value: p - partition number, range - [1... 4] 3. When the system is successfully disarmed, it will reply with confirmation by SMS text message to the user phone number that sent the SMS text message.

SMS SMS User ESIM364

Fig. No. 10

MANUAL ELDES ESIM364 V1.2 13

3.2.4 Arm by EKB2 Keypad EKB2

1. To arm the system, enter any out of 30 available 4-digit user passwords using the number keys:

1 4 7 2 5 8 0 3 6 9

Fig. No. 11

Enter user password (and select partition):

Partitioned system: uuuu → OK → Non­partitioned system: uuuu → OK → [p] part­name → OK

Value:

partition name.

Example: 1111

→ OK → [2] PART2 → OK

2. Non-partitioned system – When a valid user password is entered, the system will initiate exit delay, the keypad’s buzzer will emit short beeps and the keypad will display screen view. icon next to the countdown timer. When the system is successfully armed, the keypad will display icon for 5 seconds and switch to home • Partitioned system; arming the same partition as the keypad is assigned to – When a valid user pass­ word is en tered, the keypad will display the partition selection menu. Once a partition that is to be armed is selected, the system will initiate exit delay. During the exit delay, the keypad’s buzzer will emit short beeps and the keypad will display ARMING part-name message for 3 seconds followed by partition selection menu. If key is touched during exit delay, the keypad will display icon next to the countdown timer. When successfully armed, the keypad will display icon for 3 seconds and switch to home screen view.

• Partitioned system; arming a different partition than the keypad is assigned to – When a valid user password is entered, the keypad will display the partition selection menu. Once a partition that is to be armed is selected, the system will initiate exit delay, but will not indicate it on EKB2 keypad due to the difference between keypad partition and the one being armed. Then the keypad will display ARMING part-name message for 3 seconds followed by partition selection menu. When the keypad back-light ti­ meout expires, the home screen view will follow.

3. In addition, when the system is successfully armed, it will reply with confirmation by SMS text message to the first preset user phone number (by default), assigned to the same partition as the user password.

4. When attempting to arm the system in case of violated zone / tamper presence, the system will not permit to arm it. For more details on how to view the violated zone / tamper number, please refer to 3.4 Alarm Indi- cations & Viewing Violated Zones / Tampers. For more details on how to arm the system in case of violated zones presence, please refer to 3.5 Bypassing & Activating Zones.

NOTE: If the user fails to enter a correct user password 10 times in a row, the system will block the keypad for 2 minutes and the keypad will display KEYPAD BLOCKED message. While the keypad is blocked, the system prevents from entering any user password. The keypad will automatically unblock once the 2-minute time has expired and display KEYPAD UNBLOCKED message.

14

3.2.5 Disarm & Turn off the Alarm by EKB2 Keypad EKB2

1. The system will initiate the entry delay countdown (by default – 15 seconds) after the user has entered the secured area. Entry delay countdown is intended for user to disarm the system before the alarm is caused. The countdown is indicated by short beeps emitted by keypad buzzer and by long steady beep emit ted by buzzer connected to the alarm system (if any).

2. To disarm the system or turn off the alarm, enter any out of 30 available 4-digit user passwords using the num­ ber keys:

1 4 7 2 5 8 0 3 6 9

Fig. No. 12

Enter user password (and select partition):

Partitioned system: uuuu → OK → Non­partitioned system: uuuu → OK → [p] part­name → OK Value: uuuu – 4­digit user password; p – partition number, range – [1... 4], part-name – up to 15 characters partition name.

Example: 1111

→ OK → [2] PART2 → OK

3. When the system is successfully disarmed: • Non-partitioned system – When a valid user password is entered, the keypad will display seconds and switch to home screen view. icon for 3 • Partitioned system – When a valid user password is entered, the keypad will display the partition se­ lection menu. Once a partition that is to be disarmed is selected, the keypad will display part-name DISARMED message for 3 seconds and return to partition selec tion menu followed by home screen view after the keypad back-light timeout expires.

4. In addition, when the system is successfully disarmed, it will reply with confirmation by SMS text message to the first preset user phone number (by default), assigned to the same partition as the user password.

NOTE: If the user fails to enter a correct user password 10 times in a row, the system will block the keypad for 2 minutes and the keypad will display KEYPAD BLOCKED message. While the keypad is blocked, the system prevents from entering any user password. The keypad will automatically unblock once the 2-minute time has expired and display KEYPAD UNBLOCKED message.

MANUAL ELDES ESIM364 V1.2 15

3.2.6 Arm by EKB3/EKB3W Keypad EKB3/ EKB3W

1. a) To arm the system partition that the keypad is assigned to, enter any out of 30 available 4-digit user passwords using the number keys:

1 4 7 2 5 8 0 3 6 9

Fig. No. 13

Enter user password:

uuuu Value: uuuu – 4­digit user password Example: 1111 b) To arm a different system partition, switch the keypad partition by pressing and holding the [*] key for 3 seconds until you will hear 3 short beeps and specify the keypad partition using the number keys:

Switch keypad partition:

* (3 sec.) p Value: p - partition number, range - [1... 2].

After switching the keypad partition, enter any out of 30 available 4-digit user passwords using the number keys:

Enter user password:

uuuu Value: uuuu – 4­digit user password Example: 1111 2. The keypad indicator ARMED will light ON and the system will initiate the exit delay countdown (by default – 15 seconds) intended for user to leave the secu red area. The countdown is indicated by short beeps emitted by keypad buzzer and the buzzer connected to the alarm system (if any).

3. When the system is successfully armed, it will reply with confirmation by SMS text message to the first preset user phone number (by default), assigned to the same partition as the user password.

SMS User ESIM364 Fig. No. 14 4. When attempting to arm the system in case of violated zone / tamper presence, the system will not permit to arm it. For more details on how to view the violated zone / tamper number, please refer to 3.4 Alarm Indications & Viewing Violated Zones / Tampers. For more details on how to arm the system in case of violated zones presence, please refer to 3.5 Bypassing & Activating Zones.

ATTENTION: Your alarm system installer must enable keypad partition switch feature before you can use it.

NOTE: The user can control only the first two system partitions using EKB3/EKB3W keypad.

16

3.2.7 Disarm & Turn off the Alarm by EKB3/EKBW Keypad EKB3/ EKB3W

1. The system will initiate the entry delay countdown (by default – 15 seconds) after the user has entered the secured area. Entry delay countdown is intended for user to disarm the system before the alarm is caused. The countdown is indicated by short beeps emitted by keypad buzzer and long steady beep emitted by buzzer connected to the alarm system (if any).

2. a) To disarm the system partition that the keypad is assigned to, enter any out of 30 available 4-digit user passwords using the number keys:

1 4 7 2 5 8 0 3 6 9

Fig. No. 15

uuuu Value: uuuu – 4­digit user password Example: 1111 b) To disarm a different system partition, switch the keypad partition by pressing and holding the [*] key for 3 seconds until you will hear 3 short beeps and specify the keypad partition using the number keys:

Switch keypad partition:

* (3 sec.) p Value: p - partition number, range - [1... 2].

After switching the keypad partition, enter any out of 30 available 4-digit user passwords using the number keys:

Enter user password:

uuuu Value: uuuu – 4­digit user password Example: 1111 3. When the system is successfully disarmed, the keypad indicator ARMED will light and the system will reply with confirmation by SMS text message to the first preset user phone number (by default), assigned to the same partition as the user password.

SMS User ESIM364 ATTENTION: Your alarm system installer must enable keypad partition switch feature before you can use it..

NOTE: The user can control only the first two system partitions using EKB3/EKB3W keypad.

Fig. No. 16

MANUAL ELDES ESIM364 V1.2 17

3.2.8 Arm by iButton® Key

1. To arm the system, touch the iButton® key reader by any out of 5 iButton® keys:

Fig. No. 17

2. The system will initiate the exit delay countdown (by default – 15 seconds) intended for user to leave the secu red area. The countdown is indicated by short beeps emitted by buzzer connected to the alarm system (if any).

3. When the system is successfully armed, it will reply with confirmation by SMS text message to the first preset user phone number (by default), assigned to the same partition as the iButton key.

SMS User ESIM364

Fig. No. 18

4. When attempting to arm the system in case of violated zone / tamper presence, the system will not permit to arm it and it will reply with violated zone / tamper number to the user phone number that made a phone call. For more de­ tails on how to arm the system in case of violated zones presence, please refer to 3.5 Bypassing & Activating Zones.

3.2.9 Disarm & Turn off the Alarm by iButton® Key

1. The system will initiate the entry delay countdown (by default – 15 seconds) after the user has entered the secured area. Entry delay countdown is intended for user to disarm the system before the alarm is caused. The countdown is indicated by long steady beep emitted by buzzer connected to the alarm system (if any).

2. To disarm the system or turn off the alarm, touch the iButton® key reader by any out of 5 iButton® keys:

Fig. No. 19

3. When the system is successfully disarmed, it will reply with confirmation by SMS text message to the first preset user phone number (by default), assigned to the same partition as the iButton key.

SMS User ESIM364

Fig. No. 20

18

3.2.10 Arm by EWK1 – Wireless Key-fob EWK1

1. To arm the system, press 1 out of 4 EWK1 buttons (by default – button) assigned to arm the alarm system. Arm the system

Fig. No. 21

2. The system will initiate the exit delay countdown (by default – 15 seconds) intended for user to leave the secu red area. The countdown is indicated by short beeps emitted by buzzer connected to the alarm system (if any).

3. When the system is successfully armed, it will reply with confirmation by SMS text message to the first preset user phone number (by default), assigned to the same partition as the keyfob.

SMS User ESIM364

Fig. No. 22

4. When attempting to arm the system in case of violated zone / tamper presence, the system will not permit to arm it and it will reply with violated zone / tamper number to the user phone number that made a phone call. For more details on how to arm the system in case of violated zones presence, please refer to 3.5 Bypassing & Activating Zones MANUAL ELDES ESIM364 V1.2 19

3.2.11 Disarm & Turn off the Alarm by EWK1 – Wireless Key-fob EWK1

1. The system will initiate the entry delay countdown (by default – 15 seconds) after the user has entered the se­ cured area. Entry delay countdown is intended for user to disarm the system before the alarm is caused. The countdown is indicated by long steady beep emitted by buzzer connected to the alarm system (if any).

2. To disarm the system or turn off the alarm, press 1 out of 4 EWK1 buttons (by default – button) assigned to disarm the alarm system Disarm the system

Fig. No. 23

3. When the system is successfully disarmed, it will reply with confirmation by SMS text message to the first pre­ set user phone number (by default), assigned to the same partition as the keyfob.

SMS User ESIM364

Fig. No. 24

20

3.2.12 Arm by EWK2 – Wireless Key-fob EWK2

1. To arm the system, press 1 out of 4 EWK2 buttons (by default – button) assigned to arm the alarm system. Arm the system

Fig. No. 25

2. The system will initiate the exit delay countdown (by default – 15 seconds) intended for user to leave the secu red area. The countdown is indicated by short beeps emitted by buzzer connected to the alarm system (if any).

3. When the system is successfully armed, it will reply with confirmation by SMS text message to the first preset user phone number (by default), assigned to the same partition as the keyfob.

SMS User ESIM364

Fig. No. 27

4. When attempting to arm the system in case of violated zone / tamper presence, the system will not permit to arm it and it will reply with violated zone / tamper number to the user phone number that made a phone call. For more details on how to arm the system in case of violated zones presence, please refer to 3.5 Bypassing & Activating Zones MANUAL ELDES ESIM364 V1.2 21

3.2.13 Disarm & Turn off the Alarm by EWK2 – Wireless Key-fob EWK2

1. The system will initiate the entry delay countdown (by default – 15 seconds) after the user has entered the se­ cured area. Entry delay countdown is intended for user to disarm the system before the alarm is caused. The countdown is indicated by long steady beep emitted by buzzer connected to the alarm system (if any).

2. To disarm the system or turn off the alarm, press 1 out of 4 EWK2 buttons (by default – disarm the alarm system button) assigned to Disarm the system

Fig. No. 28

3. When the system is successfully disarmed, it will reply with confirmation by SMS text message to the first pre­ set user phone number (by default), assigned to the same partition as the keyfob.

SMS User ESIM364

Fig. No. 29

22

3.3 Activating STAY Mode

EKB2 EKB3/ EKB3W

• Stay mode allows the user to remain in the secured area after arming the system. In Stay mode, the system does not cause the alarm when the zones, set up to operate under this mode, become violated. • This system will automatically Stay-arm in case the user does not leave the secured area (if Delay zone is not vio­ lated and restored) during exit delay countdown. • This mode is usually used when arming the system before night.

• There is no exit delay countdown when arming the system in Stay mode by keypad.

• Stay mode is NOT activated when arming the system by phone call or SMS text message.

EWK1 EWK2

NOTE: Delay Zone Becomes Instant in Stay Mode feature may be enabled on your system. In that case the alarm will be caused instantly instead of entry delay countdown being initiated if a delay zone becomes violated while the system is operating in Stay mode. For more details, please, contact your alarm system installer.

3.3.1 Arm by EKB2 Keypad in STAY Mode Manually EKB2

1. Navigate through the following menu path using P2 and arrow keys and enter a valid user password using the number keys to arm the system in Stay mode manually:

Menu path:

Partitioned system: P2 → uuuu → OK Non­partitioned system: P2 → uuuu → OK → [p] part­name → OK Value: uuuu ­ 4­digit user password 2. • Non-partitioned system – When P2 key is touched and a valid user password is entered, the system will be come armed in Stay mode.When the system is successfully armed, the keypad will display icon for 5 seconds and switch to home screen view containing STAY message. • Partitioned system – When P2 key is touched and a valid user password is en tered, the keypad will display the partition selection menu. Once a partition that is to be armed is selected, the keypad will display ARMING part-name message for 3 seconds and return partition selection menu followed by home screen view after the keypad back-light timeout expires.

3. In addition, when the system is successfully armed, it will reply with confirmation by SMS text message to the first preset user phone number (by default), assigned to the same partition as the user password.

SMS User ESIM364

Fig. No. 30

4. When attempting to arm the system in case of violated zone / tamper presence, the system will not permit to arm it. For more details on how to view the violated zone / tamper number, please refer to 3.4 Alarm Indications & Viewing Violated Zones / Tampers. For more details on how to arm the system in case of violated zones presence, please refer to 3.5 Bypassing & Activating Zones.

NOTE: If the user fails to enter a correct user password 10 times in a row, the system will block the keypad for 2 minutes and the keypad will display KEYPAD BLOCKED message. While the keypad is blocked, the system prevents from entering any user pass­ word. The keypad will automatically unblock once the 2-minute time has expired and display KEYPAD UNBLOCKED message.

For more details on how to disarm & turn off the alarm by EKB2 keypad, please refer to chapter 3.2.5 Disarm & Turn off the Alarm by EKB2 Keypad.

MANUAL ELDES ESIM364 V1.2 23

3.3.2 Arm by EKB3/EKB3W Keypad in STAY Mode Manually EKB3/ EKB3W

1. a) To Stay-arm the system partition in that the keypad is assigned to, enter any out of 30 available 4-digit user passwords using the number keys:

Press the [STAY] key & enter user password:

STAY uuuu Value: uuuu ­ 4­digit user password Example: STAY1111 b) To Stay-arm a different system partition, switch the keypad partition by pressing and holding the [*] key for 3 seconds until you will hear 3 short beeps and specify the keypad partition using the number keys:

Switch keypad partition:

* (3 sec.) p Value: p - partition number, range - [1... 2].

2. When the system is successfully armed, keypad indicator ARMED will light ON.

3. In addition, the system will reply with confirmation by SMS text message to the first preset user phone number (by default), assigned to the same partition as the user password.

SMS User ESIM364

Fig. No. 31

4. 4. When attempting to arm the system in case of violated zone / tamper presence, the system will not permit to arm it. For more details on how to view the violated zone / tamper number, please refer to 3.4 Alarm Indications & Viewing Violated Zones / Tampers. For more details on how to arm the system in case of violated zones presence, please refer to 3.5 Bypassing & Activating Zones. ATTENTION: Your alarm system installer must enable keypad partition switch feature before you can use it.

NOTE: The user can control only the first two system partitions using EKB3/EKB3W keypad.

For more details on how to disarm & turn off the alarm by EKB3/EKB3W keypad, please refer to chapter 3.2.7 Disarm & Turn off the Alarm by EKB3/EKB3W Keypad.

24

3.4 Alarm Indications & Viewing Violated Zones / Tampers

By default configuration, the system makes a phone call to User 1 in case of alarm. By answering the call, the user is able to listen on his/her mobile phone to what is happening in area surrounding ESIM364 unit. This feature is pro­ vided by a microphone (if any) connected to ESIM364.

The phone call is made to the next preset user (presumably to User 2) in a row in case the previous user was unreach­ able (was “out of radio coverage”, provided “busy” signal or did not answer the call). This routine is continued until one of the preset users is reachable, but will not go in a circle i. e. return to User 1 if none of the users were reachable. In addition, the system will not make a phone call to the next preset user in a row if the previous user was reachable, but rejected the phone call. The phone calls will cease to be made to the user as soon as the system is disarmed.

CALL User ESIM364

Fig. No. 32

NOTE: Your alarm system installer may have configured the system to make the phone calls to the next available user even if the previous one has answered the call.

SMS

By, default configuration the system sends an SMS text message containing violated zone or tamper number in case of alarm. The SMS text message can also contain a star * character next to the violated tamper in case the tamper violation is caused due to wireless connection loss between ESIM364 and a wireless device (if any).

This SMS text message is sent to User 1. The system sends the SMS text message to the next preset user (presumably to User 2) in a row only if the previous user was unreachable (the system did not receive a successful SMS text mes­ sage delivery confirmation in 20 seconds from the recipient). This routine is continued until one of the preset users is reach able, but will not go in a circle i. e. return to User 1 if none of the users were reachable. The SMS text messages will cease to be sent to the user as soon as the system is disarmed.

SMS User ESIM364 Fig. No. 33 See also chapter 3.6 Viewing System Information. NOTE: Your alarm system installer may have configured the system to send the SMS text message to the next available user even if the previous one has received it.

MANUAL ELDES ESIM364 V1.2 25

EKB2

The built-in EKB2 buzzer and ESIM364 buzzer (if any) provide short beeps continuously in case of alarm. In addi­ tion, the LCD screen back-light level is boosted and the alarm message (depending on violated zone type or tamper violation) is displayed in the main screen view of EKB2 screen. The buzzer can be silenced by disarming the system using any method. Navigate through the following menu path using OK and arrow keys to view the violated zone or tamper number:

Menu path:

View violated zone: View violated tamper: OK OK → VIOLATED ZONES → OK → ZONE 1... 76 → VIOLATED TAMPERS → OK → TAMPER 1... 76

EKB3/ EKB3W

The built-in EKB3/EKB3W buzzer emits short beeps continuously and ESIM364 buzzer (if any) emits a steady beep in case of alarm. In addition, the violated zone number is indicated by illuminated zone LED or flashing indicator SYSTEM (if the violated zone number is above 12). The violated tamper number is indicated by illuminated indicator SYSTEM. The buzzer can be silenced by disarming the system using any method.

For more details on EKB3/EKB3W violated high-numbered zone & tamper number indication, please refer to chapter 3.10

Indication of System Faults.

By default configuration, the siren/bell (if any) provides continuous alarm sound for 1 minute in case of alarm. The fire alarm is indicated by pulsating siren/bell alarm sound. The alarm sound can be silenced by disarming the system using anymethod.

3.5 Bypassing & Activating Zones

Arming the system is disabled while there’s at least 1 violated zone. Bypassing allows to temporally deactivate a certain violated zone and arm the alarm system after­wards.

EKB2

Navigate through the following path using OK and arrow keys to bypass a violated zone (-s):

Menu path:

Bypass a zone: Bypass all zones: OK → BYPASS → OK → BYPASS LIST 1... 3 → OK → ZONE 1... 76 → OK → BYPASS → OK OK → BYPASS → OK → BYP VIOLATED ZONES → OK Navigate through the following path using OK and arrow keys to activate a bypassed zone:

Menu path:

Activate a bypassed zone: OK → BYPASS → OK → BYPASS LIST 1... 3 → OK → ZONE 1... 76 → OK → UNBYPASS → OK NOTE: Zones can only be bypassed and activated when the system is not armed.

EKB3

Bypass a violated zone by entering the following combination using [BYPS], number and [#] keys:

Press the [BYPS] key, enter zone number & user password:

BYPS nn uuuu # Value: nn – zone number, range – [01... 76]; uuuu – 4­digit user password.

Example: BYPS051111# NOTE: The zone will stay bypassed until the system is disarmed. Once the system is disarmed, the zone‘s current state will be indicated on the keypads. ATTENTION: Bypassing a violated tamper is NOT allowed. Please, restore the tamper (for example: close sensor‘s enclosure) before arming the system 26

3.6 Viewing System Information

SMS

1. In order to find out the system‘s current information, send the following SMS text message to the system‘s phone number from any out of 10 preset user phone numbers:

SMS text message content:

ssss_INFO Example: 1111_INFO 2. The system will reply to the user phone number that sent the SMS text message with the following up-to-date information: • System date & time.

• System status: partition armed (ON)/disarmed (OFF).

• GSM signal strength level.

• Main power supply status.

• Temperature of the area surrounding ESIM364 primary & secondary temperature sensors (if any).

• State of zones (OK/alarm).

SMS SMS User ESIM364 Fig. No. 34 See also 3.9 Managing Temperature Information.

3.7 Managing Periodical System Information

SMS

1. By default configuration, the SMS text message mentioned in chapter 3.6 Viewing System Information is sent periodically to User 1 phone number at 11:00 daily.

SMS User ESIM364 Fig. No. 35 2. In order to set a different SMS sending frequency (in days) and time, send the following SMS text message to the system‘s phone number from any out of 10 preset user phone numbers:

SMS text message content:

ssss_INFO:ff.tt

Value: ff – frequency in days, range – [0... 10]; tt – time, range – [0... 23] Example: 1111_INFO:2.15 (every 2nd day at 15:00) NOTE: Unlike system information SMS text message upon request, periodical system information SMS text message does not included zone states, PGM output names and status.

MANUAL ELDES ESIM364 V1.2 27

3. In order to disable periodic SMS text message, send the following SMS text message to the system‘s phone number from any out of 10 preset user phone numbers:

SMS text message content:

ssss_INFO:0.0

Example: 1111_INFO:0.0 4. The system will reply with confirmation by SMS text message to the user phone number that sent the SMS text message.

SMS SMS User ESIM364

Fig. No. 36

3.8 Viewing Zone & PGM Output Information

SMS

1. In order to find out the current zone & PGM output information, send the following SMS text message to the system‘ s phone number from any out of 10 preset user phone numbers:

SMS text message content:

ssss_STATUS Example: 1111_STATUS 2. The system will reply to the user phone number that sent the SMS text message with the following up-to-date information: • System status: partition armed (ON)/disarmed (OFF).

• Status of zones & PGM outputs (ON/OFF).

• Zone alarm texts.

• PGM output names.

SMS SMS User ESIM364

Fig. No. 37

28

3.9 Managing Temperature Information

SMS

1. The system supports up to 8 temperature sensors. If at least 1 or 2 (primary and/or secondary) temperature se sors are installed in your system, it can send an SMS text message containing temperature value in case the set lowest or highest temperature limit value is exceeded. This SMS text message is sent to User 1 only. By default configuration this SMS text message is disabled.

SMS User ESIM364

Fig. No. 38

2. In order enable or set a different lowest, highest temperature limit value or specify a name for a determined primary or secondary temperature sensor, send the following SMS text message to the system‘s phone num­ ber from any out of 10 preset user phone numbers:

SMS text message content:

ssss_TEMPn:MIN:tm,MAX:tmx,NAME:temp-sens-name Value: n - primary or secondary temperature sensor number, range - [1... 8]; tm ­ lowest temperature limit boun­ dary in °C, range - [-55... 125]; tmx - highest temperature limit boundary in °C, range - [-55... 125]; temp-sens-name - temperature sensor name, length - 4... 24 characters. Example: 1111_TEMP2:MIN:-15,MAX:30,NAME:Garage 3. In order to disable this SMS text message, send the following SMS text message to the system‘s phone number from any out of 10 preset user phone numbers:

SMS text message content:

ssss_TEMPn:MIN:0,MAX:0 Value: n - primary or secondary temperature sensor number, range - [1... 8] Example: 1111_TEMP1:MIN:0,MAX:0 4. In order to find out, which temperature sensors are set as primary and secondary, send the following SMS text message to the system‘s phone number from any out of 10 preset user phone numbers:

SMS text message content:

ssss_TEMPI?

Example: 1111_TEMPI:?

5. In order to find out the current temperature of all temperature sensors, send the following SMS text message to the system‘s phone number from any out of 10 preset user phone numbers:

SMS text message content:

ssss_ITEMP:?

Example: 1111_ITEMP:?

6. The system will reply with confirmation by SMS text message to the user phone number that sent the SMS text message.

SMS SMS User ESIM364

Fig. No. 39

See also chapter 3.6 Viewing System Information MANUAL ELDES ESIM364 V1.2 29

EKB2

Navigate through the following path using OK and arrow keys to view real-time temperature sensor values:

Menu path:

OK → TEMP SENSORS INFO → OK → 1... 8

3.10 Indication of System Faults

EKB2

Message FLT displayed in the lower left side of the home screen view indicates presence of system faults. In order to find out more on the particular system fault, please open menu section FAULTS. The description on each system fault is indicated in the table below.

Menu path:

OK → FAULTS → OK

Name

MAIN POWER LOSS LOW BATTERY BATTERY DEAD/MISS BATTERY FAILED SIREN FAILED VIOLATED TAMPER DATE/TIME NOT SET GSM CONNECT FAILED GSM ANTENNA FAILED WLESS ANTENNA FAIL

Description

Main power supply is lost Low backup battery power - backup battery voltage is 10.5V or lower Backup battery is not present or the battery voltage has run below 5V Backup battery requires replacement - backup battery resistance is 2Ω or higher Siren is disconnected/broken One or more tampers are violated Date/time not set GSM connection is lost GSM antenna is disconnected/broken Wireless antenna is disconnected/broken 30

EKB3/ EKB3W

Yellow LED SYSTEM indicates system faults. SYSTEM LED indications are mentioned in the table below.

SYSTEM LED

Illuminated continously Flashing

Description

One ore more zones or tampers are violated; other system faults One or more high-numbered zones are violated In order to find out more on the particular system problem please , enter command A. After this procedure the system will activate red zone LEDs for 15 seconds. The description on each LED indication is mentioned in the table below.

Zone LED

5 7 8 9 10 11 12 1 2 3 4

Description

Main power supply is lost Low backup battery power - backup battery voltage is 10.5V or lower Backup battery is not present or the battery voltage has run below 5V Backup battery requires replacement - backup battery resistance is 2Ω or higher Siren is disconnected/broken One or more tampers are violated Date/time not set GSM connection is lost One or more high-numbered zones (Z13 - Z76) are violated GSM antenna is disconnected/broken Wireless antenna is disconnected/broken In order to find out which particular high-numbered zone is violated please , enter command B.

In order to find out which particular tamper is violated please , enter command C.

A. System fault indication - enter command:

[CODE#]

B. Violated high zone indication – enter command:

[CODE1]

C. Violated tamper indication – enter command:

[CODE2] The number of violated high-numbered zone or tamper can be calculated using the table below according to the formu­ la: number from zone LED section B + number from zone LED section A.

Example: LED #3 from section A is flashing and LED #8 from section B is illuminated continuously. According to the table below LED #8 is equal to number 18, therefore 18 + 3 = 21. Result: Violated high-numbered zone or tamper number is 21.

Zone LED section - A (flashing)

Zone LED 1 = 1 Zone LED 2 = 2 Zone LED 3 = 3 Zone LED 4 = 4 Zone LED 5 = 5 Zone LED 6 = 6

Zone LED section - B (illuminated continously)

Zone LED 7 = 12 Zone LED 8 = 18 Zone LED 9 = 24 Zone LED 10 = 30 Zone LED 11 = 36 Zone LED 12 = 42 MANUAL ELDES ESIM364 V1.2 31

3.11 Controlling Electrical Appliances

Your system features 4 or more PGM outputs intended for connection and control of various electrical appliances. This provides a possibility to control garage gates, turn on and off your house heating, lighting, cooling system, reset smoke sensors to restored state etc. The PGM outputs must be configured by your installer before using them.

SMS

1. In order to turn ON a specified PGM output, send the following SMS text message to the system’s phone num­ ber from any out of 10 preset user phone numbers:

SMS text message content:

ssss_Coo:ON or ssss_out-name:ON Value: oo – PGM output number, range – [1... 76]; out-name – PGM output name. Example: 1111_Pump:ON 2. In order to turn OFF a specified PGM output, send the following SMS text message to the system‘s phone number from any out of 10 preset user phone numbers:

SMS text message content:

ssss_Coo:OFF or ssss_out-name:OFF Value: oo – PGM output number, range – [1... 76]; out-name – PGM output name. Example: 1111_C2:OFF 3. The system will reply with confirmation by SMS text message to the user phone number that sent the SMS text message.

SMS SMS User ESIM364 Fig. No. 40 32

3.12 Turning ON/OFF the Electrical Appliances for a Determined Time Period

SMS

1. In order to instantly turn ON a specified PGM output and keep it in this state for a determined time period, send the following SMS text message to the system’s phone number from any out of 10 preset user phone numbers:

SMS text message content:

ssss_Coo:ON:hr.mn.sc

or ssss_out-name:ON:hr.mn.sc

Value: oo – PGM output number, range – [1... 76]; hr – hours, range – [00... 23], mn – minutes, range – [00... 59]; sc – seconds, range – [00... 59]; out-name – PGM output name.

Example: 1111_Pump:ON:00.00.25 2. In order to instantly turn OFF a specified PGM output and keep it in this state for a determined time period, send the following SMS text message to the system’s phone number from any out of 10 preset user phone numbers:

SMS text message content:

ssss_Coo:OFF:hr.mn.sc

or ssss_out-name:OFF:hr.mn.sc

Value: oo – PGM output number, range – [1... 76]; hr – hours, range – [00... 23], mn – minutes, range – [00... 59]; sc – seconds, range – [00... 59]; out-name – PGM output name.

Example: 1111_C3:OFF:13.25.56 3. The system will reply with confirmation by SMS text message to the user phone number that sent the SMS text message.

SMS SMS User ESIM364 Fig. No. 41 NOTE: PGM output can be turned ON for a determined time period only when it is in OFF state.

NOTE: PGM output can be turned OFF for a determined time period only when it is in ON state.

3.13 Viewing Event Log

This feature allows to chronologically register up to 500 timestamped records regarding the following system events: • System start. • System arming/disarming. • Zone violated/restored. • Tamper violated/restored. • Zone bypassing. • Wireless device management. • Temperature deviation by MIN and MAX boundaries. • System faults. The event log is of LIFO (last in, first out) type that allows the system to automatically replace the oldest records with the the latest ones.

EKB2

Navigate through the following menu path using OK and arrow keys and enter user password to view the event log:

Menu path:

OK → VIEW EVENT LOG → OK → uuuu → OK Value: uuuu ­ 4­digit user password.

MANUAL ELDES ESIM364 V1.2 33

4. If the Alarm System is Connected to Monitoring Station

The following system features may be disabled by your alarm system installer if the system is con nected to a monitoring station: • Confirmation by SMS text message when arming, disarming & turning off the alarm by phone call, SMS text message, EKB2/EKB3/EKB3W keypad, iButton® key, EWK1/EWK2 - wireless key-fob..

• Alarm indication by phone call.

• Alarm indication by SMS text message.

• Violated zone/tamper name indication by SMS text message.

• Temperature indication by SMS text message.

• Periodical system information by SMS text message.

• Main power loss/restore indication by SMS text message.

• Any other SMS text message generated by the system.

NOTE: For complete system configuration and control, please refer to ESIM364 installation manual located at www.eldes.lt/en/download 34

MANUAL ELDES ESIM364 V1.2 35

Made in Lithuania. www.eldes.lt

iButton is a registered trademark of Maxim Integrated Products, Inc.

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement