TVLogic F-10A Owner Manual

PDF Download

Document

FIELD

PRODUCTION

MONITOR

# Operation manual_V1.7_200909

F-10A

CAUTION

MAIN FEATURES

CONTROLS & FUNCTIONS

MENU TREE & ADJUSTMENT

MENU OPERATIONS

04p

06p

07p

10p

11p

[1] PICTURE

[2] COLOR

[3] MARKER

[4] VIDEO

[5] WAVEFORM

[6] AUDIO

[7] SYSTEM

BUTTON FUNCTIONS

OTHER FUNCTIONS

23p

24p

AVAILABLE SIGNAL FORMATS

34p

VIDEO SUPPORT RESOLUTION

35p

OUTPUT SIGNAL FORMATS

36p

PRODUCT SPECIFICATIONS

OPTIONAL ACCESSORIES

37p

38p

11p

12p

15p

16p

18p

20p

21p

Field Production Monitor

01 CAUTION

• Always use set voltage. (DC 6~34V)

• When using a DC Adapter other than the one

supplied by the manufacturer, please be advised

that the adapter with DC 12V/3A ~ 6A can be

compatible with the monitor.

• All operating instructions must be read and

understood before the product is operated.

• These safety and operating instructions must be

kept in safe place for future reference.

• All warnings on the product and in the instructions

must be observed closely.

• All operating instructions must be followed.

• Do not use attachments not recommended by the

manufacturer. Use of inadequate attachments

can result in accidents.

• This product must be operated on a power

source specified on the specification label.

• If you are not sure of the type of power supply

used in your home, consult your dealer or local

power company. For units designed to operate

on batteries or another power source, refer to the

operating instructions.

• The power cords must be routed properly to

prevent people from stepping on them or objects

from resting on them. Check the cords at the

plugs and product.

• In case of using other 12V DC adapters instead of

the standard adapter provided by the manufacturer,

please check the proper load capacity (or current

capacity) and use an adapter with stable voltage.

• Do not overload DC outlets or extension cords.

Overloading can cause or electric shock.

• Never insert an object into the product through

vents or openings. High voltage in the product,

and inserting an object can cause electric shock

and/or short internal parts. For the same reason,

do not spill water or liquid on the product.

• Do not attempt to service the product yourself.

Removing covers can expose you to high voltage

and other dangerous conditions. Request a

qualified service person to perform servicing.

• If any of the following conditions occurs, unplug

the power cord from the DC outlet, and request a

qualified service person to perform repairs.

a. When the power cord or plug is damaged.

b. When a liquid was spilled on the product or

when objects have fallen into the product.

c. When the product has been exposed to rain or

water.

d. When the product does not operate properly as

described in the operating instructions. Do not

touch the controls other than those described

in the operating instructions.

Improper adjustment of controls not described

in the instructions can cause damage, which often

requires extensive adjustment work by a

qualified technician.

e. When the product has been dropped or

damaged.

f. When the product displays an abnormal

condition.

Any noticeable abnormality in the product

indicates that the product needs servicing.

• In case the product needs replacement parts,

make sure that the service person uses replacement

parts specified by the manufacturer, or those with

the same characteristics and performance as the

original parts. Use of unauthorized parts can

result in fire, electric shock and/or other danger.

• Upon completion of service or repair work, request

the service technician to perform safety checks to

ensure that the product is in proper operating

condition.

• When mounting the product on a wall or ceiling,

be sure to install the product according to the

method recommended by the manufacturer.

• Unplug the power cord from the DC outlet before

cleaning the product. Use a damp cloth to clean

the product. Do not use liquid cleaners or aerosol

cleaners.

• Unplug the power cord from the AC outlet if you

do not use the product for considerably long time.

Field Production Monitor

01 CAUTION

• Do not use the product near water, such as bathtub,

washbasin, kitchen sink and laundry tub,

swimming pool and in a wet basement.

• Keep the product away from direct rays of the

Sun-light.

• Do not place the product on an unstable cart,

stand, tripod or table. Placing the product on an

unstable base can cause the product to fall,

resulting in serious personal injuries as well as

damage to the product. Use only a cart, stand,

tripod, bracket or table recommended by the

manufacturer or sold with the product. When

mounting the product on a wall, be sure to follow

the manufacturer’s instruction. Use only the

mounting hardware recommended by the

manufacturer.

• When relocating the product placed on a cart, it

must be moved with the utmost care.

• The power cord plug shall be connected to a

MAINS socket outlet with a protective earthing

connection.

• Infrared devices can cause noise or malfunction

under condition as below.

- Parts of the body come into contact with the

infrared transmiter or acoustic device.

- Obstacles can cause electrical changes if there is

a partition in the middle or in the wall.

- Exposure to radio interference from medical

equipment, microwave ovens, wireless LAN

devices, etc. with the same frequency band.

• Unplug the power cord from the AC outlet when

happening any problem in the product.

• Sudden stops, excessive force and uneven floor

surface can cause the product to fall from the cart.

• The vents and other openings in the cabinet are

designed for ventilation. Do not cover or block

these vents and openings since insufficient

ventilation can cause overheating and/or shorten

the life of the product. Do not place the product

on a bed, sofa, rug or other similar surface, since

they can block ventilation openings. This product

is not designed for built-in installation; do not

place the product in an enclosed place such as a

bookcase or rack, unless proper ventilation is

provided or the manufacturer’s instructions are

followed.

• In case of installation the product on the rack, the

inside of the product would be overheated due to

heat from other devices near by and the decrease

of air circulation, which could damage to the

monitor. To prevent the damage, please have

enough space for the monitors and use fan to

avoid heat and maintain the operating temperature.

(Refer to the specication of the product).

• The LCD panel used in this product is made of

glass. Therefore, it can break when the product is

dropped or applied with impact. Be careful not to

be injured by broken glass pieces in case the LCD

panel breaks.

• Keep the product away from heat sources such as

radiators, heaters, stoves and other heat generating

products (including amplifiers).

Field Production Monitor

02 MAIN FEATURES

F-10A Monitor contains the following features :

• Compatible with various SDI signals formats

(SD/HD/3G)

- This product is compatible with various SDI

signals - 480i, 576i, 720p, 1080i, 1080p, 1080psf

• HDMI(with HDCP) Signal

- This product is compatible with various HDMI

signals.

• HDMI To SDI / SDI To HDMI Conversion Output

- This product features an HDMI To SDI conversion

output so that video source from HDMI In

terminal

can be output through SDI Out terminal.

- The SDI To HDMI conversion output is also

supported. The video source from SDI In

terminal can be output through HDMI Out

terminal.

• All-in-one type system

- Slim and all-in-one type monitor that requires

no additional accessories, for optimized space

utilization.

• Waveform/Vectorscope/Audio Level Meter

Function

- Waveform & Vector Scope

- Embedded Audio Level Meter

• Audio Out

- Stereo Audio Out through phone Jack.

• Knob Control

- Easy to adjust user configuration using the

control knob on the top of the monitor.

• BLUE ONLY / MONO / Focus Assist/ H/V Delay

Function

• Range Error/Luma(Y’) Zone Check(Color/Zebra

Type) Function

• Internal Pattern Generator (0~100% Gray/

ColorBar+Pluge)

• Various Markers & Safety Areas

- Center Marker, Safety Area Marker, Marker Mat,

Marker Size, Fit Marker, Thickness Adjustment

function

• 1:1 Scan/Zoom Function

- Used to display the original image resolution

without scaling to match a certain resolution or

an aspect ratio.

- Select ‘Pixel to pixel’ to display unscaled images,

and select ‘Zoom’ to enlarge the original image.

- Zoom Scroll Function (Left/Right, Top/Bottom)

• Power

- Basically, the product is powered by a normal DC

source.

- The product can be battery-powered.

* DC 6~34V (Typical)

• Additional features

- Camera Mounting Hole x 8, Screen Tally Function,

VESA Mounting Standard, 450cd/ m 2

Brightness,

1,000 : 1 Contrast, OSD user interface.

03 CONTROLS & FUNCTIONS

F-10A ALL PART

MENU<EXIT>

SOURCE

KNOB

Field Production Monitor

FUNCTION F1~F6

PHONEJACK

HDMI OUT

HDMI IN

USB

REAR TALLY

SDI OUT

SDI IN/OUT

(SELECT)

SDI IN

POWER BUTTON

GPI

ETHERNET

DC POWER

Field Production Monitor

03 CONTROLS & FUNCTIONS

TOP & BOTTOM

• [MENU/EXIT/SOURCE] Button

- Used to activate the OSD menu.

- When the OSD menu is activated, press this

button to exit from the menu.

- Press the button for more than 2 seconds to

activate Input Select menu. (SDI, HDMI)

- Use the [ENCODER] Knob to change the Input

Signal.

• [UP/DOWN/ENTER] Knob

- Used to move within the menu when OSD menu

is activated, and is also used to decrease or

increase the value of the selected feature.

- Press the knob to select the main menu and the

sub menus.

- Press the button for more than 2 seconds to

activate the HOT Key menu. (VOLUME / BRIGHT /

CONTRAST / CHROMA / SHAPRNESS / PEAKING

BOOST)

- Press the button for less than 2 seconds to

activate the PRESET function.

• [F1]~[F3] Button

- Press the button for less than 2 seconds to

activate the function.

- Press the button for more than 2 seconds to

activate Function Select menu. (Scan, Aspect,

H/V delay, etc.)

- Press the button for more than 2 seconds to

indicate previously selected function.

- Use the Knob to change the function.

• [USB]

- This terminal is used to upgrade the firmware or

color calibration made by TVLogic.

Field Production Monitor

03 CONTROLS & FUNCTIONS

SIDE & REAR

• [HDMI IN]

- Signal input terminal for HDMI signal.

• [HDMI OUT]

- Signal output terminal for HDMI signal.

- Video source from SDI input terminal can be

converted to HDMI format.

• [HEADPHONE] (Phonejack)

- Used for Stereo Audio Output through Phone

Jack. (video signals with embedded audio only)

• [REAR TALLY]

- Activates same as [SCREEN TALLY].

• [DC POWER / TALLY] (XLR 4P)

* Rated Power Input : DC 6V (1.8A) / 34V (0.32A)

* When using a DC Adapter other than the one

supplied by the manufacturer, please be advised

that the adapter with DC 12V/3A ~ 6A can be

compatible with the monitor.

• [SDI IN] (BNC)

- Signal input terminal for HD/SD/3G SDI signal.

• [SDI IN/OUT] (BNC)

- Can be used as SDI IN or SDI OUT depending on

the menu setting.

• [SDI OUT] (BNC)

- Signal output terminal for HD/SD/3G SDI signal.

- Video source from HDMI input terminal can be

converted to SDI format.

• [POWER] Switch

- Used to turn the power on and off.

<Warning!!>

When using the product make sure to ground, whenever possible, before connecting the input signal cable in order to prevent any possible damage to the product or connected devices. The damage may include signal noise, malfunction of main board or display panel. And the connected devices such as camera or video source player may also be influenced through signal cable.

Please check if the AC power source and the power extender or power distributor is grounded.

Field Production Monitor

04 MENU TREE & ADJUSTMENT

[1] MENU TREE

• OSD(On-Screen Display) Menu helps to use

varous different functions.

• This Picture is the menu structure for F-10A

PICTURE 같이

BRIGHT

CONTRAST

CHROMA

SHARPNESS

PEAKING BOOST

KNOB LOCK

3DLUT LOAD

3DLUT SYNC

3DLUT IMPORT 1

3DLUT IMPORT 2

3DLUT IMPORT 3

UNLOCK

REC 709

SYNCHRONIZATION

NONE01

F-10A

[3] MENU CONTROL SEQUENCE

• Menu control sequence follows the order below.

1. Press MENU button to activate the OSD menu.

2. Move to a desired menu using the Knob.

3. Press the Knob to select a menu and move to

select a sub-menu by scrolling the Knob.

4. Press the Knob to select the desired sub menu.

(The selected sub-menu will be highlighted)

5. Press the ENTER button or the MENU button to

save the new value after adjusting the value by

scrolling the Knob.

6. Press MENU button to return to previous menu

and if there is no previous menu, the OSD menu

will be removed from the screen.

[2] MENU CONTROL

• User may control various functions using the

MENU button and the Knob on the top of the

monitor.

05 MENU OPERATIONS

[1] PICTURE

PICTURE 같이

BRIGHT

CONTRAST

CHROMA

SHARPNESS

PEAKING BOOST

KNOB LOCK

3DLUT LOAD

3DLUT SYNC

3DLUT IMPORT 1

3DLUT IMPORT 2

3DLUT IMPORT 3

UNLOCK

REC 709

SYNCHRONIZATION

NONE01

F-10A

• BRIGHT

- Used to set the brightness(=offset) level from

-100 to 100.

* Brightness can be adjusted by using the Knob

on the top of the monitor.

• CONTRAST

- Used to set the contrast(gain) level from -100 to

100.

* Contrast can be adjusted by using the Knob on

the top of the monitor.

• CHROMA

- Used to set the saturation level from -50 to 50.

* Chroma can be adjusted by using the Knob

on the top of the monitor.

• SHARPNESS

- Used to set the Sharpness level from 0 to 24.

* Sharpness can be adjusted by using the Knob

on the top of the monitor.

• PEAKING BOOST

- Used to set the Peaking Boost level from 0 to 24.

* Peaking Boost can be adjusted by using the

Knob on the top of the monitor.

• KNOB LOCK

- Locks the Knob control.

• 3DLUT LOAD

- Used to apply the internally stored 3DLUT.

- Maximum 3 x 3DLUT files can be stored.

- The file name can be set up to 20 characters

including the extension.

• 3DLUT SYNC

- Used to load a list of available 3DLUT files

currently stored in the FLASH MEMORY.

- Available 3DLUT formats are Cube, GV Lut,

Quantel, Davinci and Assimilate Scratch.

- Available sizes of the 3DLUT are 17 or 33.

• 3DLUT IMPORT 1/2/3

- Used to save the 3DLUT stored in the external

memory to the internal memory 1/2/3 area.

- Once saved, the 3DLUT can be maintained even

when the power is turned ON/OFF.

- The file name can be set up to 20 characters

including the extension.

Field Production Monitor

05 MENU OPERATIONS

[2] COLOR

COLOR 같이

STANDARD

VIDEO RANGE

PEAK LUMINANCE

BLACK LEVEL

COLOR GAMUT

COLOR TEMP

EOTF

LOCAL DIMMING

EETF

HLG SG

THROUGHOUT

CAM LUT

CAM LUT THR

UHD

LIMITED 109

100

0.001

BT.2020

6500K

2.4

OFF

F-10A

PAGE (1/2)

• STANDARD

- Used to select the color and dynamic rage of the

screen.

- Available options are HD, UHD, DCI-P3, PQ, HLG,

SLog3 and User1/2/3.

* Activates only in the User1/2/3 mode.

• VIDEO RANGE

- Used to select the range of digital video signal.

* FULL : Input signal 0~255 (8bit), 0~1023

(10bit) (When connecting the PC)

* LIMITED109 : Input signal Y‘: 16~235, CbCr:

16~240 (8bit)/ Y‘: 64~940, CbCr: 64-960 (10bit)

• PEAK LUMINANCE

- Used to select the Peak Luminance of the

monitor.

- Available options are 100, 200, 300, 400, 500,

600, 700, 800, 900, 1000, 2000, 4000 and 10000.

- Activates only in the User1/2/3 mode.

• BLACK LEVEL

- The minimum black level of the video signal

can be set differently depending on the

performance of the monitor or the lighting

environment. For example, the lowest luminance

that the F-7H mk2 can display is 0.002, but it is

necessary to adjust the offset level to about

0.2nit when using under bright light.

- At this time, when the black level is set to 0.2,

dark gradations below 0.2 nit are expressed

without crushing.

- Activates only in the User1/2/3 mode.

• COLOR GAMUT

- Used to select the standard color gamut.

- Available options are BT.709, DCI-P3, BT.2020

and Native.

* The submenus may be activated in the User1/2/3

mode only.

• COLOR TEMP (Color Temperature)

- Controls the color temperature.

- Available options are 6500K, 9300K and User.

* The submenus may be activated in the User1/2/3

mode only.

• EOTF (Electro-Optical Transfer Function)

- Electrophotic conversion Functions(ex: Gamma

or HDR curve).

- Available modes are 2.2, 2.4, 2.6, PQ, HLG and

SLOG3.

* The submenus may be activated in the User1/2/3

mode only.

• LOCAL DIMMING

- Used to set the Local Dimming Backlight mode.

- This mode is supported by the local dimming

backlight model (LUM-310R) and does not

support F-10A.

Field Production Monitor

05 MENU OPERATIONS

[2] COLOR

COLOR 같이

STANDARD

VIDEO RANGE

PEAK LUMINANCE

BLACK LEVEL

COLOR GAMUT

COLOR TEMP

EOTF

LOCAL DIMMING

EETF

HLG SG

THROUGHOUT

CAM LUT

CAM LUT THR

UHD

LIMITED 109

100

0.001

BT.2020

6500K

2.4

OFF

F-10A

PAGE (1/2)

• EETF (Electrical-Electrical Fransfer Function)

- Used to display the HDR image(without clipping)

within the actual luminance range (black level

and peak luminance) that the monitor can

express. In the Auto mode, the HDR image is

converted within the range of set peak luminance

and black level. In the OFF mode, the video

signal outside of the set range is clipped.

- Available modes are OFF and AUTO.

- Available only when the EOTF is set to PQ or

SLOG3.

* The submenus may be activated in the User1/2/3

mode only.

• HLG SG (HLG System Gamma)

- Used to set the System Gamma of HLG mode.

- In the Auto mode, the value of the System

Gamma changes automatically according to the

previously set peak luminance. When it is OFF,

the value is set to default value of 1.2.

- Activates only when the EOTF is set to HLG.

* The submenus may be activated in the User1/2/3

mode only.

• SG (System Gamma)

- The System Gamma of HLG is automatically

calculated and displayed according to the set

peak luminance.

- Activates only when the EOTF is set to HLG and

the HLG SG is Auto.

• CAM LUT (Camera LUT)

- Used to change the Camera LUT.

- Available LUTs are OFF, LOG-C, C-LOG, S-LOG

1,2,3 and REDGamma 3,4.

• CAM LUT THROUGH (Camera LUT Throughout)

- Apply the currently applied LUT to Throughout.

Field Production Monitor

05 MENU OPERATIONS

[2] COLOR

COLOR 같이

TEMP COLOR

GAIN RED

GAIN GREEN

GAIN BLUE

BIAS RED

BIAS GREEN

BIAS BLUE

COLOR COPY

COLOR SPACE

6500K_60P

BT.709

F-10A

• COLOR SPACE

- Used to select the standard color space.

- Available options are BT.709, DCI-P3, BT.2020 and

Native.

PAGE (2/2)

• TEMP COLOR (Color Temperature)

- Controls the color temperature and allows

instant access to preset the color temperature

settings.

- Available color temperatures are 6500K, 9300K

and User1/2/3.

* In User 1/2/3 modes, user can define custom

RGB GAIN, BIAS (=Offset) and Color Copy values.

• GAIN RED / GREEN / BLUE

- Used to set Red/Green/Blue Gain(or Picture,

Contrast) level from -256 to 255.

* Only available in User 1/2/3 mode.

• BIAS RED / GREEN / BLUE

- Used to set Red/Green/Blue Bias(or Offset,

mainly affects on Black level) from -100 to 100.

* Only available in User 1/2/3 mode.

• COLOR COPY

- Used to copy the R/G/B Gain value of pre-stored

color temperature settings.

- In User mode, find and select the color

temperature and press the Knob to copy and

apply the Gain value to GAIN RED, GAIN GREEN,

GAIN BLUE.

* Only available in User 1/2/3 mode.

Field Production Monitor

05 MENU OPERATIONS

[3] MARKER

MARKER 같이

ENABLE

MARKER

CENTER MARKER

SAFETY AREA

FIT MARKER

MARKER MAT

MARKER COLOR

THICKNESS

USER MARKER H1

USER MARKER H2

USER MARKER V1

USER MARKER V2

OFF

WHITE

F-10A

+ 0

+1920

+ 0

+1080

• ENABLE

- Used to activate the Marker function.

• MARKER

- Available Marker types are OFF, 16:9, 4:3, 4:3 ON

AIR, 15:9, 14:9, 13:9, 1.85:1, 2.35:1, 1.85:1& 4:3 and

USER.

• CENTER MARKER

- Displays the Center Marker on the screen.

• SAFETY AREA

- Used to select to display and controls the size

and availability of the Safety Area.

- Available sizes are 80%, 85%, 88%, 90%, 93%,

100%, EBU ACTION 16:9, EBU GRAPHIC 16:9, EBU

ACTION 14:9, EBU GRAPHIC 14:9, EBU ACTION 4:3

and EBU GRAPHIC 4:3.

• FIT MARKER

- Used to activate or inactivate the Fit Marker

function.

- When the Marker type is selected in the Marker

menu, a border line of the Safety Area will be

displayed inside the Marker. Images below

show the difference between Fit Marker ON and

OFF.

MARKER : 4:3

SAFETY AREA : 90%

FIT MARKER : OFF

MARKER : 4:3

SAFETY AREA : 90%

FIT MARKER : ON

• MARKER MAT

- Used to set the darkness level outside of the

MARKER area from OFF(transparent) to 7(Black).

- The bigger the value, the darker the color.

• MARKER COLOR

- Used to set the color of the MARKER lines.

- Available colors are white, gray, black, red, green

and blue.

• THICKNESS

- Used to set the thickness of the MARKER lines.

- Thickness level is from 1 to 7 by the pixel unit.

• USER MARKER H1

- Used to set the position of the first horizontal

marker line.

- Displayed when the MARKER menu is set to

USER.

• USER MARKER H2

- Used to set the position of the second horizontal

marker line.

- Displayed when the MARKER menu is set to

USER.

• USER MARKER V1

- Used to set the position of the first vertical

marker line.

- Displayed when the MARKER menu is set to

USER.

• USER MARKER V2

- Used to set the position of the second vertical

marker line.

- Displayed when the MARKER menu is set to

USER.

Field Production Monitor

05 MENU OPERATIONS

[4] VIDEO

VIDEO 이

SCAN

ASPECT

H/V DELAY

BLUE ONLY

USER ASPECT HOR

USER ASPECT VER

3G FORMAT

H/V FLIP

ZOOM

ZOOM SPLIT

ZERO SCAN

16:9

OFF

NORMAL

OFF

F-10A

+1920

+1080

PAGE (1/2)

• SCAN

- Used to change the Scan mode. Scroll up and

down using the Knob and the mode will chang

as the following sequence. [Zero Scan] -> [Over

Scan] -> [Pixel-To-Pixel] -> [User Aspect]

* [USER ASPECT]: User can control the aspect

ratio by adjusting width and height of the display.

* See section “7. Other Functions [1] User

Aspect” for more information.

• ASPECT

- Used to change the Aspect Ratio.

- Regardless of the original Aspect ratio of the

input signal, the Aspect Modes are changed as

follow sequence. : [16:9][4:3][2.35:1][1.85:1][15:9]

[16:10][Anamorphic1.3x][Anamorphic1.5x]

[Anamorphic2.0x][Auto]

* [Auto] mode enables the Aspect Ratio of the

output signal to be synchronized to the original

Aspect Ratio of the input signal.

• H/V DELAY

- Used to monitor the Blanking area of H sync and

V sync.

• BLUE ONLY

- Used to switch in the order of [Off]-[Blue Only]-

[Mono]-[Off].

- Press the button to remove red and green

components from the input signal and display

blue componet only.

- Press the button again to switch to mono-

chrome mode which has no chroma signal.

• USER ASPECT HORIZONTAL/USER ASPECT

VERTICAL

- Activated only when the [SCAN] mode is set to

[User Aspect] .

- User can adjust the Horizontal and Vertical size

of the screen.

- See section “7. Other Functions [1] User Aspect”

for more information.

• 3G FORMAT

- Used to select 3G-SDI A/B input format among

NORMAL MODE(AUTO - A 422 10BIT_YCbCr

50/60P), A 444 10/12BIT_YCbCr, A 444 10/12BIT_

RGB, A 422 12BIT_YCbCr, B 444 10/12BIT_YCbCr, B

444 10/12BIT_RGB, B 422 12BIT_YCbCr, B 422

10BIT_YCbCr 50/60P.

- In NORMAL MODE, automatically detected when

Payload signal is contained.

• H/V FLIP

- Allows the displayed image to be flipped

horizontally or vertically.

- This feature provides flexible mounting options

for camera operators.

- In the [AUTO] mode, the vertical FLIP operates

automatically according to the position of the

unit.

- Activates in the order : [H Flip]-[V Flip]-[H/V Flip]-

[AUTO]

• ZOOM

- Used to magnify the image up to 90% on a pixel

basis and display on full screen.

* (e.g.,10% Zoom : If the input signal’s resolution is

1920 x 1080, only 90% (1728(H) x 972(V)) of the

image would be shown on full screen without

the remaining 10% (192(H) x 108(V)) of the

image.)

* See section “7. Other Functions -> [4] Zoom” for

more information.

• ZOOM SPLIT

- Used to magnify the image.

- Used to zoom the specified area sequentially.

- Designable areas are Left-Top, Right-Top, Left-

Bottom, Right-Bottom and Center.

Field Production Monitor

05 MENU OPERATIONS

[4] VIDEO

VIDEO 이

TIMECODE

FOCUS ASSIST

FOCUS AS COLOR

FOCUS AS LEVEL

SCR TALLY

LOW BAT DISPLAY

ARRI CAM STATUS

LDS INFO

INDEX LETTER

OFF

RED

OFF

LOW

RED

OFF

F-10A

+ 0

PAGE (2/2)

• TIMECODE

- Used to set the Time Code.

- Available modes are [Off], [VITC], and [LTC].

• FOCUS ASSIST

- Focus Assist helps the shooters to easily find out

the exact area in the picture with good focus,

simply by adding colors on the shape or

boundaries of the object in the picture.

- Activates in order of [Mono On]-[Color On]- [Off]

* [Color On] : Only the boudary of the area with

good focus is displayed with the designated

color.

*[Mono On] : The boundary of the area with good

focus is colored with the designated color, while

the rest of the areas(pixels) have only Y’(Luma)

signals to be black & white image.

* See section “7. Other Functions [6] Focus Assist”

for more information.

• FOCUS AS COLOR (Focus Assist Color)

- Used to select a color for Focus Assist among

red, green and blue.

- This feature is available only when the Focus

Assist mode is activated.

• FOCUS AS LEVEL (Focus Assist Level)

- Used to set the edge difference value between

the edges in an image.

- Available values are from 0 to 100. Larger the

value the more sophisticated the detail

detection.

- Designated color is displayed when the

difference of the edges exceeds the previously

set value.

- This feature is available only when the FOCUS

ASSIST mode is activated.

• SCR TALLY (Screen Tally)

- Used to set Tally operation according to the

input level of TALLY IN terminal which is among

the terminals of XLR 4P connector in the rear.

• LOW BAT DIS (Low Battery Display)

- Used to set Low Battery Display function.

- When the battery becomes weak, [Low Battery]

sign is indicated on the OSD.

• ARRI CAM STATUS

- Used to display the camera status information

provided by ARRI ALEXA camera on the OSD.

- When the Arri Cam Status is activated, the screen

will be squeezed (1742 x 980).

• LDS INFO (Lens Data System Information)

- Used to set the information display of the Lens

Data System information.

- The information is displayed in the order : [Lens

name] - [Focal length] - [Iris] - [DOF Min] - [Focus

distance] - [DOF Max].

• INDEX LETTER

- Used to set the monitor index letter on the upper

right.

Field Production Monitor

05 MENU OPERATIONS

[5] WAVEFORM

WAVEFORM

ENABLE

TYPE

INTENSITY

TRANS

SIZE

LINE WAVEOFORM

SEL LINE POS

LUMA CHECK

LUMA ADJUST

RANGE ERROR

Y MAX

Y MIN

C MAX

C MIN

Y PICTURE BLINK

C PICTURE BLINK

OFF

OPAQUE

SAMLL

OFF

F-10A

• ENABLE

- Used to activate/ deactivate the Waveform

which is selected in the Waveform/Vectorscope

Type menu.

• TYPE

- This function sets the Waveform and Vectorscope.

- Available options are different according to the

Input signal.

- Activates in the order: YCbCr: Off - Waveform

- Vectorscope - Waveform Wide - Waveform

YCbCr - RGB(Conv.)-Wave_Vector - Vector_YCbCr

- Full Waveform(Y) - Full Vectorscope.

• INTENSITY

- Used to set the brightness level of the Waveform/

Vectorscope display from 1 to 63.

- The higher the number the brighter the

waveform will be.

• TRANS (Transparency)

- Used to select the transparency option of the

Waveform/ Vectorscope between Opaque and

Blend.

- Even if the option is set to [Opaque], it will

automatically turn to [Blend] when the main

OSD overlaps the waveform/vectorscope.

And turns back to [Opaque] when the main OSD

disappears.

• SIZE

- Adjust the size of the Waveform or Vectorscope.

- Can select among [NORMAL] and [LARGE].

• LINE WAVEFORM

- This item is utilized to display the entire data or

one line data on the Waveform.

• SEL LIN POS (Select Line Position)

- Used to select specific Vertical Line for Waveform/

Vectorscope.

- This is available when LINE Waveform is activated.

- Use the Knob to select a desired vertical line.

- Control range varies according to the resolution

of the input SDI signal.

* PAL : Min. 1, Max. 625

* NTSC : Min. 1, Max. 525

* 720p : Min. 1, Max. 750

* 1080i : Min. 1, Max. 1125

* 1080p : Min. 1, Max. 1125

• LUMA CHECK

- Displays the Luma(Y’) level of the input image

in colors.

- Can select between [Color Pattern] or [Zebra

Pattern].

- Each pixel’s Y’ analized and changed to a certain

color or zebra pattern according to the Index on

the right side of the screen.

- When a pixel’s Y’ level is under 0%(16), the color

/ diagonal line will be colored Green.

- When the pixel’s Y’ level is over 100%(235), the

color / diagonal line will be colored Red.

- When the Y’ level of a pixel is between 0~100%,

the pixel is displayed with Gray, except for

selected Luma Zone.

- In the [Color Pattern] mode, a 5% zone of the

selected Y’ level will be colored Pink(5%) and

±10% will be colored Yellow(-10% from Pink) and

Cyan(+10% from Pink).

- In the [Zebra Pattern] mode, ± 5% of the selected

Y’ Level will be displayed with diagonal lines.

Field Production Monitor

05 MENU OPERATIONS

[5] WAVEFORM

WAVEFORM

ENABLE

TYPE

INTENSITY

TRANS

SIZE

LINE WAVEOFORM

SEL LINE POS

LUMA CHECK

LUMA ADJUST

RANGE ERROR

Y MAX

Y MIN

C MAX

C MIN

Y PICTURE BLINK

C PICTURE BLINK

OFF

OPAQUE

SAMLL

OFF

F-10A

• LUMA ADJUST

- Used to set the Y’ level to be colored Yellow, Pink

and Cyan in [Color Pattern] mode, or to set Y’

level zone to be displayed with diagonal lines in

[Zebra Pattern] mode simply by scrolling the

Knob.

- Available values are 0w ~ 100%.

* See section “7. Other Function [5] Luma(Y’) Zone

Check” for more information.

• RANGE ERROR

- Used to set whether or not to activate Y MAX,

Y MIN, C MAX, C MIN, Y PICTURE BLINK and C

PICTURE BLINK functions.

- The values of Y MAX, Y MIN, C MAX, C MIN are

indicated in Waveform/Vectorscope.

- If [Y PICTURE BLINK] or [C PICTURE BLINK] is

enabled, the section of image that exceeds the

selected values of Y MAX, Y MIN, C MAX and C

MIN shall blink.

* In the case of RGB input, Range Error is not

supported.

* See section “7. Other Function [7] Range Error”

for more information.

• Y MAX

- Used to set the maximum Luma(Y’) level from 0

to 255.

- Pixels with values exceeding the max Y’ level will

blink on the screen, and be displayed in red on

the Waveform.

• Y MIN

- Used to set the minimum Luma(Y’) level from 0

to 255.

- Pixels with values exceeding the max Y’ level will

blink on the screen, and be displayed in red on

the Waveform.

• C MAX

- Used to set the maximum chroma(C’) level from

0 to 255.

- Pixels with values exceeding the max Y’ level will

blink on the screen, and be displayed in red on

the Waveform.

• C MIN

- Used to set the minimum chroma(C’) level from

0 to 255.

- Pixels with values exceeding the max Y’ level will

blink on the screen, and be displayed in red on

the Waveform.

• Y PICTURE BLINK

- Used to set whether or not to blink pixels with

values exceeding Y MAX and Y MIN.

• C PICTURE BLINK

- Used to set whether or not to blink pixels with

values exceeding C MAX and C MIN.

Field Production Monitor

05 MENU OPERATIONS

[6] AUDIO

AUDIO

VOLUME

AUD LEFT

AUD RIGHT

LEVEL METER

LVM DISPLAY

LVM REFERENCE

LVM SIZE

PEAK DECAY TIME

OFF

FOF

OFF

PAIR

-18dB

SMALL

F-10A

• VOLUME

- Used to control the output volume for the

[AUDIO OUT] on the back of the monitor.

- Control range is from 0 to 30.

• AUD LEFT (Audio Left)

- Used to set embedded audio channel for left

audio out of [AUDIO OUT] terminal on the back

of the monitor.

- Available values are between CH1~CH16 and

Ext..

* In the HDMI mode, Left is set to CH1.

• AUD RIGHT(Audio Right)

- Used to set embedded audio channel for right

audio out of [AUDIO OUT] terminal on the back

of the monitor.

- Available values are between CH1~CH16 and

Ext..

* In the HDMI mode, Right is set to CH2.

• LEVEL METER

- Used to set the Level Meter for the embedded

audio.

- Available options are :

SDI Input : [Off]-[16CH(Hor.)]-[16CH(Ver.)]

HDMI Input: [Off]-[2CH(Hor.)]-[2CH(Ver.)]

* 16 CH(HOR.) : Displays 8 channels on top

left and 8 channels on top right of the screen

horizontally.

* 16 CH(VER.) : Displays 8 channels on center

left and 8 channels on top right of the screen

vertically.

• LVM DISPLAY (Level Meter Display)

- Used to set the display method for audio level

meter.

- Available modes are Group and Pair.

* In the HDMI mode, the mode is set to Pair.

• LVM REFERENCE (Level Meter Reference)

- Display the default audio level meter value,

- Available options are -18dB and -20dB.

- Audio level meter within selected value turns to

green and exceeded audio level is displayed in

yellow.

- Audio level exceeding -4dB is displayed in red.

• LVM SIZE (Level Meter Size)

- Used to control the size of the audio level meters.

- Available options are NORMAL and LAGRE.

• PEAK DECAY TIME

- Sets the reduction time for max value indication

of audio signals.

- Control range is from MIN 0 to MAX 100. Bigger

number means a longer display time for max

value.

Field Production Monitor

05 MENU OPERATIONS

[7] SYSTEM

SYSTEM

DEFAULT

LUMINANCE

INTERNAL PAT

DISPLAY ENABLE

ECO SAVING

SW UPGRADE

DHCP

IP ADDRESS

SUBNET MASK

GATEWAY

PORT

APPLY

MAC ADDRESS

VERSION

SERIAL NUM

F-10A

OFF

100

OFF

STATIC

192.168.1.80

255.255.255.0

192.168.1.1

10262

OFF

FF:FF:FF

SW 00 FPGA 00 BOARD 00

12345678 PAGE (1/2)

• DEFAULT

- Used to initialize OSD values to factory default.

- Available modes are DEFALUT and FACTORY.

- In the DEFALUT mode, except for the stored 3D

LUT, all values are initialized.

- In the FACTORY mode, all values are initialized to

factory default.

• LUMINANCE

- Used to indicate the current Luminance value .

- In the case of System Default, the value returns

to factory default(after color calibration).

- Available values are from 0 to 50.

• INTERNAL PAT (INTERNAL PATTERN)

- Generates ColorBar, Pludge and Grayscale

Pattern internally.

- Selectable range for Gray Pattern is from 0% to

100% with 5% increment.

* See section “7. Other Function -> [12] Internal

Pattern” for more information.

• DISPLAY ENABLE

- Used to set the LUMINANCE to the minimum

value when the time set in the still image output

is exceeded.

- When video is output or the MENU button is

pressed, the LUMINANCE is reset to the original

value.

- Settable options are ON, 5MIN, 10MIN, 20MIN

and 30MIN.

- In the Function Key, the screen can be turned

ON/OFF immediately by user’s choice.

• ECO SAVING

- Used to save power consumption automatically

when there is no monitor signal.

- When the signal is supplied, the brightness of

the monitor will be changed to the set value.

• S/W UPGRADE

- Used to upgrade the firmware using USB (Thumb

drive).

* See section “7. Other Functions -> [13] Firmware

Upgrade” for more information.

• DHCP

- Used to activate/deactivate the DHCP function.

• IP ADDRESS / SUBNET MASK / GATEWAY

- Used to set the IP Address connected to a

Monitor.

• PORT

- Used to set the port number of the monitor.

- Default is set to 10262.

• APPLY

- Use to apply changed value of IP Address, Subnet

mask, Gateway and Port no.

• MAC ADDRESS

- Displays the MAC Address.

• VERSION

- Displays current firmware version.

• SERIAL NUM (Serial Number)

- Displays the serial number of the monitor.

Field Production Monitor

05 MENU OPERATIONS

[7] SYSTEM

SYSTEM

POWER LED

EXTERNAL FAN

PIN 1

PIN 2

PIN 3

PIN 4

PIN 5

PIN 6

PIN 7

PIN 8

OFF

HDMI

SDI A

SDI B

TALLY RED

TALLY GREEN

BLUE ONLY

POWER ON/OFF

GND

F-10A

PAGE (1/2)

• POWER LED

- Used to set the POWER LED ON/OFF.

- When is set to ON, the LED is always on and when

it is OFF, the LED is off after booting.

• EXTERNAL FAN

- Connect the FAN to the USB port of the monitor

and set the ‘EXTERNAL FAN’ mode to ‘FAN ON’.

(Can also be set in Function Key).

- Press the button of the FAN to adjust the wind

speed.

- OFF : The LED indicator light up in red and the

FAN turns off. When powering on the FAN for

the first time, it is set to OFF mode.

- FAST : The LED indicator light up in green and

the FAN operates at high speed.

- SLOW : The LED indicator light up in orange and

the FAN operates at slow speed.

* When using ‘Calibration’ or ‘USB Upgrade’ via

the USB port, set

• This item activates/ inactivates the REMOTE

function.

- The user may designate a function for each pin

and each pin’s default setting is as follows.

- The default settings are as follows:

PIN 1 : HDMI CHANNEL

PIN 2 : SDI-A CHANNEL

PIN 3 : SDI-B CHANNEL

PIN 4 : TALLY RED

PIN 5 : TALLY GREEN

PIN 6 : BLUE ONLY

PIN 7 is POWER ON/OFF use only, PIN 8 is GND

REMOTE (RJ-45)

1 8

1: Pin1

2: Pin2

3: Pin3

4: Pin4

5: Pin5

6: Pin6

7: Pin7

8: GND

Field Production Monitor

06 BUTTON FUNCTIONS

INPUT BUTTON & FUNCTION KEY SET BUTTON

[1] INPUT BUTTON

SDI A

SDI B

HDMI

NO VIDEO

• F-10A unit is capable of processing SDI/HDMI

Input signal.

1. Press the [MENU < EXIT >] button on the front of

the monitor for more than 2 seconds and activate

the OSD menu as shown on the below.

2. Input resolution displays on the buttom of the

OSD screen.

3. Press the [MENU < EXIT >] button again to

remove the OSD menu from display.

* If no image displays after selecting the desired

input mode, check and make sure that your

connection is not lost or disconnected.

[2] FUNCTION KEY SET BUTTON

SDI

HDMI

NO VIDEO

MARKER

H/V DELAY

BLUE ONLY

ZOOM

ZOOM SPLIT

FREEZE

AUDIO LVM

TIME CODE

FOCUS ASSIST

WAVEFORM

LUMA(Y`) ZONE

RANGE ERROR

H/V FLIP

F1 FUNC SEL

MAX BRIGHTNESS

CAMERA LUT

DISPLAY ENABLE

INPUT SELECT

ARRI METADATA

EXTERNAL FAN

• Used to make a quick setting of the Function

Key.

1. Press the function button(F1~F6) on the front

of the monitor for more than 2 seconds and

activate the OSD menu as follows.

2. Move to a desired function with the Knob and

press the Knob to select.

3. Once the function is set, press the Function

button(F1~F6) to activate the function.

Field Production Monitor

07 OTHER FUNCTIONS

• Used to adjust the Width/Height diaplay ratio.

1. Select [Aspect] mode in the OSD menu by pressing the function button on the right top of the monitor

to activate the [USER ASPECT] mode.

2. After the activation, press the Knob to begin controlling. Adjust the ratio using the knob.

USER ASPECT

WIDTH +1920

HEIGHT +1080

- Adjust the ratio using the Knob.

- Control range for width: 0~1920.

- Control range for height : 0~1080.

- The size-adjusted picture always stays in the center of the screen.

- The size can be adjustable with 2 increment and decrement.

* To adjust the 16:9 aspect ratio of 1920X1080 resolution into 2.35:1 aspect ratio, adjust the width and

height as 1280 x 544.

Field Production Monitor

07 OTHER FUNCTIONS

[2] WAVEFORM / VECTORSCOPE

• WAVEFORM Y

- Displays the Luma(Y’) component of the input signal into waveform.

• The Waveform/Vectorscope function can be

used only when the input signal is YUV.

• In the case of RGB input, Waveform RGB is

supported.

• Available modes in the YUV signal :

- WAVEFORM Y

- VECTORSCOPE

- WAVEFORM Wide

- WAVEFORM Y Cb Cr

- WAVE_VECTOR

- VECTOR_YCbCr

- FULL WAVEFORM(Y)

- FULL VECTORSCOPE

• WAVEFORM Cb, Cr

- Displays the Cb, Cr components of the input signal into waveform.

• VECTORSCOPE

- Displays the color components ‘B-Y’ and ‘R-Y’ of the input signals onto the X-Y axis.

- Two different types of Vetorscopes are displayed according to SD or HD input signals.

- 100% and 75% scales are indicated on the Vetorscope.rm.

100%

75%

Field Production Monitor

07 OTHER FUNCTIONS

[3] LINE SELECT (WAVEFORM/VECTORSCOPE)

• Used to select specific Vertical Line for WaveForm/VectorScope.

- This is available when LINE WaveForm is activated.

- To activate this feature, go to [Waveform]-[Waveform/Vector]-[Line Waveform]-[Select Line Position] and

use the Knob to select a vertical line.

- Selected line is indicated in White on the screen.

- Control range varies according to the resolution of the input SDI signal.

* PAL : 0~625

* NTSC : 0~525

* 720p : 0~750

* 1080 i/p : 0~1125

* Selected line is indicated on the screen.

LINE

POSITION

07 OTHER FUNCTIONS

[4] ZOOM

• Used to magnify the input signal from 0% to 90%.

- Supports Zoom Width Scroll / Zoom Height Scroll function.

- Zooms IN/OUT focused on the scrolled area.

Field Production Monitor

<ZOOM OFF>

<ZOOM 50%> <ZOOM 75%>

Field Production Monitor

07 OTHER FUNCTIONS

[5] LUMA (Y') ZONE CHECK

• COLOR PATTERN TYPE

- Displays the Luma(Y’) level of the input image in colors.

- Y’ ≥ 100% : Pixels with higher Y’ level than 100 turn to red.

- Y’ ≤ 0% : Pixels with lower Y’ level than 0 turn to green.

- Pixels with Y’ levels designated by the user are displayed in following colors - yellow, pink, cyan.

- Factory Default Y’ (Border line between pink and yellow) level is 75% and the pink color is

assigned to pixels with Y’ level from 70% to 75%.

- Yellow color is assigned to pixels with Y’ level from 75% to 85%, and Cyan from 60% to 70%.

- This function is designed for a better performance in setting the exposure when shooting with DSLR

cameras.

<Luma Zone Check OFF> <Luma Zone Check ON_Color Pattern Type>

• ZEBRA PATTERN TYPE

- Displays the pixels with designated Luma(Y’) levels with zebra pattern.

- Y’ ≥ 100%: Pixels with Y’ level over 100% turn to red diagonal stripes.

- Y’ ≤ 0% : Pixels with Y’ level under 0% turn to green diagonal stripes.

- User defined Y’ levels are displayed as black diagonal stripes.

- Factory Default Y’ level is 70% and the pixels with Y’ level from 65% to 75% is displayed with zebra pattern.

- Pixels with 10% of Y’ level is displayed as black diagonal stripes.

- This function is designed for a better performance in setting the exposure when shooting with DSLR

cameras.

<Luma Zone Check OFF> <Luma Zone Check ON_Zebra Pattern Type>

Field Production Monitor

07 OTHER FUNCTIONS

[6] FOCUS ASSIST

• Focus Assist function assigns a color to the pixels in the shape or the boundary of the image to inform

the user to achive the best focus.

- With this function, user can easily differenciate the focused area from the out-focused area especially

when shooting with a shallow depth of field.

- Available types are [Mono] and [Color] types.

* [Mono] : Background image is mono type.

* [Color] : Background image is original color type.

<Focus Assist ON> <Focus Assist Mono ON>

Field Production Monitor

07 OTHER FUNCTIONS

[7] RANGE ERROR

• Pixels with Y’ or C’ levels exceeding the designated levels of Y MAX, Y MIN, C MAX and C MIN shall blink.

- Analyzes the input signal’s Luma(Y’) and chroma information(C’) and if the input signal exceeds the

designated minimum value and maximum value, the pixel shall blink. This function is to help the user to

easily find out any unwanted level of signals and for a better exposure setting.

* In the case of RGB input, Range Error is not supported.

<Range Error OFF> <Range Error ON>

Field Production Monitor

07 OTHER FUNCTIONS

[8] HDMI To SDI SDI To HDMI CONVERSION-OUT / SDI To HDMI CONVERSION-OUT

HDMI TO SDI CONVERSION-OUT

• Video source from ‘HDMI input’ terminal can be

output through ‘SDI throughout’ terminal.

SDI TO HDMI CONVERSION-OUT

• 3G/HD/SD SDI signals from‘SDI input’ terminal

can be output through‘HDMI out’terminal.

Output

Format

Input

Format

480i(NTSC)

576i(PAL)

480P

576P

720P50

720P59.94

720P60

1080i50

1080i59.94

1080i60

1080p24

1080p25

1080p30

1080psF24

1080p50

1080p59.94

1080p60

1080p50

●

1080p60

●

480i(NTSC)

576i(PAL)

720P50

720P59.94

720P60

1080i50

1080i59.94

1080i60

1080p24

1080p25

1080p30

1080psF24

1080p50

1080p59.94

1080p60

1080p50

●

1080p60

●

※

Note : HDSLR camera manufacturers usually specify the resolution and frame rate for the recording.

The signal format that is output through HDMI terminal of cameras may differ from makers to makers.

The signal format for HDMI output and playback function of Canon HDSLRs is 59.94i. And even though

60i or 60p is specified in the specification of the cameras, the actual recording or HDMI output format

would be 59.94i or 59.94p.

Field Production Monitor

07 OTHER FUNCTIONS

[9] INTERNAL PATTERN

• Displays internally generated test patterns.

- The pattern consists of ColorBar and Pluge+ Grayscale Patterns. Full screen colors of various gray levels

(0~100%) are also embedded.

<Color Bar + Pluge Pattern> <Gray Pattern>

Field Production Monitor

07 OTHER FUNCTIONS

[10] FIRMWARE UPGRADE

• The USB(Thumb drive) which contains the F/W file is needed for Firmware Upgrade.

• Select the SW UPGRADE in the SYSTEM menu.

1. Connect the USB to the USB Slot on the bottom of the monitor.

2. Select what to update among CPU / FPGA / ALL in [S/W UPGRADE].

3. When the USB connection is completed, the S/W upgrade starts and the progress displays on the

bottom left side of the screen.

4. If the USB doesn’t connect properly or there is no file in the specified location, the error message will

be displayed on the bottom left side of the screen and the upgrade won’t start.

5. In that case, check the USB or the file location and try again.

• After USB connection, turn off and then on the monitor.

Field Production Monitor

08 AVAILABLE SIGNAL FORMATS

VIDEO

INPUT SIGNAL

480 / 59.94i (NTSC)

480 / 60p

576 / 50i (PAL)

576 / 50p

720 / 23.98p

720 / 24p

720 / 25p

720 / 30p

720 / 50p

720 / 59.94p

720 / 60p

1080 / 23.98PsF

1080 / 24PsF

1080 / 25PsF

1080 / 23.98p

1080 / 30PsF

1080 / 29.97PsF

1080 / 24p

1080 / 25p

1080 / 29.97p

1080 / 30p

1080 / 50i

1080 / 50p

1080 / 59.94i

1080 / 60i

1080 / 59.94p

1080 / 60p

640 x 400 (70Hz)

640 x 480 (60Hz)

640 x 480 (75Hz)

800 x 600 (60Hz)

800 x 600 (75Hz)

1024 x 768 (60Hz)

1024 x 768 (70Hz)

1024 x 768 (75Hz)

1280 x 768 (60Hz)

1280 x 800 (60Hz)

1280 x 1024 (60Hz)

1920 x 1080 (60Hz)

DISPLAY CHARACTER EXAMPLE

720x480 60i

720x480 60p

720x576 50iW

720x576 50p

1280x720 24p

1280x720 25p

1280x720 30p

1280x720 50p

1280x720 60p

1920x1080 48i

1920x1080 50i

1920x1080 24p

1920x1080 60i

1920x1080 24p

1920x1080 25p

1920x1080 30p

1920x1080 50i

1920x1080 25p

1920x1080 60i

1920x1080 60p

640x400 70p

640x480 60p

640x480 75p

800x600 60p

800x600 75p

1024x768 60p

1024x768 70p

1024x768 75p

1280x768 60p

1280x800 60p

1280x1024 60p

1920x1080 60p

SDI

●

HDMI

●

Field Production Monitor

09 VIDEO SUPPORT RESOLUTION

INPUT SIGNAL INTERFACES SIGNAL FORMAT (SD SDI)

SD SDI single link

720x487 (59.94i)

720x576 (50i)

INPUT SIGNAL INTERFACES SIGNAL FORMAT (HD SDI)

YCbCr 4:2:2 10bit

HD SDI single link

1280x720 (50/59.94/60P)

1920x1080 (23.98/24/25/29.97/30p) (50/59.94/60I)

(24/25/29.97/30psf)

YCbCr 4:2:2 10bit

INPUT SIGNAL INTERFACES SIGNAL FORMAT (3G SDI)

1920x1080 (60p/59.94p/50p)

1920x1080 (30/29.97/25/24/23.98/

30sF/29.97sF/25sF/24sF/23.98sF)

1920x1080i (60/59.94/50)

3G-SDI (A/B) single link 1280x720 (50/59.94/60P)

2048x1080 (60/59.94/50/30/29.97/25/24/23.98

30sF/29.97sF/25sF/24sF/23.98sF)

YCbCr 4:2:2 10bit

YCbCr 4:2:2 12bit

RGB 4:4:4 10bit / 12bit

YCbCr 4:4:4 10bit / 12bit

RGB 4:4:4 10bit

YCbCr 4:4:4 10bit

RGB 4:4:4 8bit / 10bit / 12bit

YCbCr 4:4:4 8bit / 10bit / 12bit

YCbCr 4:2:2 8bit / 10bit / 12bit

INPUT SIGNAL INTERFACES SIGNAL FORMAT (HDMI / DP)

HDMI

Single link

1080p (60/59.94/50/30/29.97/25/24/23.98)

1080i (60/59.94/50)

720p (50/59.94/60p)

480i(60) / 576i(50)

480p(60) / 576p(50)

RGB 4:4:4 8bit / 10bit / 12bit

YCbCr 4:2:2 8bit / 10bit / 12bit

1280x720(50/59.94/60p)

1920x1080(50/59.94/60p)

1920x1080(23.98/24/25/29.97/30p,60i/59.94i/50i )

* HDMI

RGB 4:4:4 8bit

YCbCr 4:4:4 8bit

YCbCr 4:2:2 8bit

3840x2160 (23.98/24/25/29.97/30p/50/59.94/60p)

RGB 4:4:4 8, 10, 12bit

YCbCr 4:4:4 8, 10, 12bit

YCbCr 4:2:2 8, 10, 12bit

YCbCr 4:2:0 8, 10, 12bit

4096x2160 (23.98/24/25/29.97/30p/50/59.94/60p)

RGB 4:4:4 8, 10, 12bit

YCbCr 4:4:4 8, 10, 12bit

YCbCr 4:2:2 8, 10, 12bit

YCbCr 4:2:0 8, 10, 12bit

Field Production Monitor

10 AVAILABLE SIGNAL FORMATS

* Active Through : same as input format

F-10A OUTPUT VIDEO FORMAT

Input Video Format

SDI

Frame rate

SDI-OUT PORT

SDI OUT

SDI-IN/OUT

(CAM LUT OFF)

SDI-IN/OUT

(CAM LUT ON)

HDMI OUT

HDMI

720 x 480i

720 x 576i

1280 x 720p

1920 x 1080i

59.94

60/59.94/50

30/29.97

25/24/23.98

30/29.97/25/24/23.98

Passive Through Active Through 1920 x 1080 60p 1920 x 1080 60p

Passive Through Active Through 1920 x 1080 50p 1920 x 1080 50p

Passive Through Active Through Active Through Active Through

Passive Through Active Through 1920 x 1080 50p 1920 x 1080 50p

Passive Through Active Through Active Through Active Through

1920 x 1080p 30sF/29.97sF

1920 x 1080p 25sF/24sF/23.98sF

1920 x 1080p 60/59.94/50

1920 x 1080p 30/29.97/25/24/23.98

2048 x 1080p 60/59.94/50

Passive Through

Active Through Active Through 1920 x 1080 60p

Active Through Active Through 1920 x 1080 50p

Active Through Active Through Active Through

2048 x 1080p 30/29.97/25/24/23.98

Passive Through Active Through Active Through Active Through

2048 x 1080p 30sF/29.97sF/25sF/24sF/23.98sF

Passive Through Active Through Active Through Active Through

HDMI

720 x 480i

720 x 576i

720 x 480p

59.94

720 x 576p

1280 x 720p

60/59.94/50

1920 x 1080p 60/59.94/50/30/29.97/25/24

1920 x 1080i 60/59.94/50

3840 x 2160p 60/59.94/30/29.97

3840 x 2160p 50/25/24/23.98

4096 x 2160p 50/25/24/23.98

4096 x 2160p 60/59.94/30

Passive Through 1920 x 1080 60p 1920 x 1080 60p Active Through

Passive Through 1920 x 1080 50p 1920 x 1080 50p Active Through

Passive Through 1920 x 1080 60p 1920 x 1080 60p Active Through

Passive Through 1920 x 1080 50p 1920 x 1080 50p Active Through

Passive Through Active Through Active Through Active Through

Passive Through 1920 x 1080 60p 1920 x 1080 60p 1920 x 1080 60p

Passive Through 1920 x 1080 50p 1920 x 1080 50p 1920 x 1080 50p