TVLogic LUM-095G Owner Manual
Advertisement
Advertisement
LUM-095G
4K/UHD
Multi-Purpose Monitor
Operation manual_V1.1
FCC (Federal Communications Commission)
This equipment has been tested and found to comply with the limits for class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interface when the equipment is operated in a commercial environment.
This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential to correct the interference at his own expense
CAUTION: Change or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.
Disposal of Old Electrical & Electronic Equipment
(Applicable in the European Union and other European countries with separate collection systems)
This symbol on the product or on its packing indicates that this product shall not be treated as household waste.
Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequence for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources.
Contents
01
02
03
04
05
Caution
Main Features
Controls & Functions
Menu Tree & Adjustment
Menu Operations
06
07
08
09
[1] PICTURE
[2] COLOR
[3] MARKER
[4] DISPLAY / VIDEO
[5] WAVEFORM
[6] AUDIO
[7] SYSTEM / GPI / UMD
Button Functions
Other Functions
Video Support Resolution
Product Specifications
04p
06p
07p
11p
12p
12p
13p
16p
17p
20p
22p
23p
29p
31p
39p
41p
4K/UHD Multi-Purpose Monitor
01 CAUTION
• Make sure to connect the power supply of the
specified voltage value: DC 12V/24V MAX 2.3A.
• When using a DC Adapter other than the one
supplied by the manufacturer, please be advised
that the adapter with DC 12V/24V MAX 2.3A can
be compatible with the monitor.
• All operating instructions must be read and
understood before the product is operated.
• These safety and operating instructions must be
kept in safe place for future reference.
• All warnings on the product and in the instructions
must be observed closely.
• All operating instructions must be followed.
• Do not use attachments not recommended by the
manufacturer. Use of inadequate attachments
can result in accidents.
• This product must be operated on a power
source specified on the specification label.
• If you are not sure of the type of power supply
used in your home, consult your dealer or local
power company. For units designed to operate
on batteries or another power source, refer to the
operating instructions.
• The power cords must be routed properly to
prevent people from stepping on them or objects
from resting on them. Check the cords at the
plugs and product.
• In case of using other 12V DC adapters instead of
the standard adapter provided by the manufacturer,
please check the proper load capacity (or current
capacity) and use an adapter with stable voltage.
• Do not overload DC outlets or extension cords.
Overloading can cause or electric shock.
• Never insert an object into the product through
vents or openings. High voltage in the product,
and inserting an object can cause electric shock
and/or short internal parts. For the same reason,
do not spill water or liquid on the product.
• Do not attempt to service the product yourself.
Removing covers can expose you to high voltage
and other dangerous conditions. Request a
qualified service person to perform servicing.
• If any of the following conditions occurs, unplug
the power cord from the DC outlet, and request a
qualified service person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid was spilled on the product or
when objects have fallen into the product.
c. When the product has been exposed to rain or
water.
d. When the product does not operate properly as
described in the operating instructions. Do not
touch the controls other than those described
in the operating instructions.
Improper adjustment of controls not described
in the instructions can cause damage, which often
requires extensive adjustment work by a
qualified technician.
e. When the product has been dropped or
damaged.
f. When the product displays an abnormal
condition.
Any noticeable abnormality in the product
indicates that the product needs servicing.
• In case the product needs replacement parts,
make sure that the service person uses replacement
parts specified by the manufacturer, or those with
the same characteristics and performance as the
original parts. Use of unauthorized parts can
result in fire, electric shock and/or other danger.
• Upon completion of service or repair work, request
the service technician to perform safety checks to
ensure that the product is in proper operating
condition.
• When mounting the product on a wall or ceiling,
be sure to install the product according to the
method recommended by the manufacturer.
• Unplug the power cord from the DC outlet before
cleaning the product. Use a damp cloth to clean
the product. Do not use liquid cleaners or aerosol
cleaners.
• Unplug the power cord from the AC outlet if you
do not use the product for considerably long time.
4K/UHD Multi-Purpose Monitor
01 CAUTION
• Do not use the product near water, such as bathtub,
washbasin, kitchen sink and laundry tub,
swimming pool and in a wet basement.
• Keep the product away from direct rays of the
Sun-light.
• Do not place the product on an unstable cart,
stand, tripod or table. Placing the product on an
unstable base can cause the product to fall,
resulting in serious personal injuries as well as
damage to the product. Use only a cart, stand,
tripod, bracket or table recommended by the
manufacturer or sold with the product. When
mounting the product on a wall, be sure to follow
the manufacturer’s instruction. Use only the
mounting hardware recommended by the
manufacturer.
• When relocating the product placed on a cart, it
must be moved with the utmost care.
• The power cord plug shall be connected to a
MAINS socket outlet with a protective earthing
connection.
• Infrared devices can cause noise or malfunction
under condition as below.
- Parts of the body come into contact with the
infrared transmiter or acoustic device.
- Obstacles can cause electrical changes if there is
a partition in the middle or in the wall.
- Exposure to radio interference from medical
equipment, microwave ovens, wireless LAN
devices, etc. with the same frequency band.
• Unplug the power cord from the AC outlet when
happening any problem in the product.
• Sudden stops, excessive force and uneven floor
surface can cause the product to fall from the cart.
• The vents and other openings in the cabinet are
designed for ventilation. Do not cover or block
these vents and openings since insufficient
ventilation can cause overheating and/or shorten
the life of the product. Do not place the product
on a bed, sofa, rug or other similar surface, since
they can block ventilation openings. This product
is not designed for built-in installation; do not
place the product in an enclosed place such as a
bookcase or rack, unless proper ventilation is
provided or the manufacturer’s instructions are
followed.
• In case of installation the product on the rack, the
inside of the product would be overheated due to
heat from other devices near by and the decrease
of air circulation, which could damage to the
monitor. To prevent the damage, please have
enough space for the monitors and use fan to
avoid heat and maintain the operating temperature.
(Refer to the specication of the product).
• The LCD panel used in this product is made of
glass. Therefore, it can break when the product is
dropped or applied with impact. Be careful not to
be injured by broken glass pieces in case the LCD
panel breaks.
• Keep the product away from heat sources such as
radiators, heaters, stoves and other heat generating
products (including amplifiers).
• If the still image is displayed on the screen in the
same position for a long period of time, the
permanent burn-in on the LCD panel may occur. So,
do not display characters or markers continuously.
If the video signals or image patterns are
continuously displayed at the maximum or high
level of luminance, the image smearing or flicker
may occur on the screen because of the LCD
panel’s structure and characteristics of materials used.
When the permanent burn-in, image smearing, or
other damages happen on the LCD panel due to the
improper use by the end user, the warranty service is
not applied.
5
4K/UHD Multi-Purpose Monitor
02 MAIN FEATURES
LUM-095G Monitor contains the following features
• Various 4K/UHD Video Input Interface
- 12G-SDI Single Link Input
- 3G-SDI Quad Link Square Division Input
- 3G-SDI Quad Link 2-Sample Interleave Input
- HDMI 2.0 Input
• HDR Emulation
- Supports various HDR EOTF such as PQ, HLG,
S-Log3
• IPS LCD Panel
- Offers the wide viewing angle with IPS
technology
• Easy & Simple Control
- Various OSD Key buttons and Input Signal
Indicators on the front panel
• Custom 3D LUT Import
- Allows the users to load their own created 3D
LUT files generated by color grading tools and
apply them to the monitor.
• Integrated Camera LUT
- LUTs for every major camera manufacturers are
integrated to the LUM-095G, and they can be
applied to the live input video.
- Log-C, C-Log, S-Log1, S-Log2, S-Log3, RED
Gamma 3, RED Gamma 4
• Advanced Color Adjustment OSD
- Provides various color adjustment menus
which enable the user to monitor the video
signal in the optimal settings.
• Waveform & VectorScope
- Provides various modes: Waveform,
VectorScope, Waveform Wide, Waveform YCbCr,
Waveform RGB, Waveform&VectorScope,
Waveform YCbCr&VectorScope, Waveform Full,
VectorScope Full
• Audio Level Meter
- Displays the level of the embedded audio
signal together with the video signal input
through SDI and HDMI.
- Level Meter channel number(16ch, 8ch, 4ch)
and direction(horizontal, vertical) adjustable
- Level Meter grouping available
- Audio channel Pair or Group selectable
- Level Meter size(Small, Large) changeable
• Video Range Adjustment: Limited 109%, Full
• Various Marker
• Grid Display: 3x3, 4x4, 5x5, 6x6
• Timecode Display: LTC, VITC
• ARRI Camera Status: LDS Info, Index Letter
• Scan: Zero Scan, Over Scan, 1:1 Scan
• User Aspect
• H Flip, V Flip, H/V Flip: Manual, Auto
• Focus Assist
• Dynamic UMD Display
• H/V Delay
• Blue/Mono Only
• Various Aspect: 16:9, 4:3, 2.35:1, 1.85:1, 15:9,
16:10
• Anamorphic: 1.3X, 1.5X, 1.8X
• Luma(Y’) Zone Check
• Range Error
• Closed Caption: CC-608, CC-708
• Zoom: 10%, 20%, ..., 90%
• Zoom Split: Left-Top, Right-Top, Left-Bottom,
Right-Bottom, Center
• Freeze
• Internal Pattern Display
• Tally Lamp and Screen Tally
• Remote Control via RS-422(RJ-45)
• GPI Control via REMOTE port
• Firmware Update & Calibration via USB(A Type)
• DC 12V to 24V supported
6
03 CONTROLS & FUNCTIONS
LUM-095G ALL PART (FRONT / REAR)
4K/UHD Multi-Purpose Monitor
TALLY
CHROMA
BRIGHT
APERTURE
HDMI
SDI
SPEAKER-LEFT
SCAN
ASPECT
MARKER
H/V DELAY
BLUE/MONO
W-FORM/VECTOR
TALLY
SDI-IN A/B
SDI-OUT C/D
RS-422 IN
RS-422 OUT
AUDIO IN
AUDIO OUT
HDMI
TALLY
REMOTE
USB
DC IN
POWER
ENTER
DOWN
F3
F2
F1
CONTRAST
VOLUME
UP
MENU
SPEAKER-RIGHT
7
4K/UHD Multi-Purpose Monitor
03 CONTROLS & FUNCTIONS
FRONT
• [SDI] Button/Lamp
- Used to select SDI-A/B input.
• [HDMI] Button/Lamp
- Used to select HDMI input.
• [SCAN] Button/Lamp
- Used to change the scan mode.
- Press the button to activate through the scan
modes: [ZERO SCAN] -> [OVER SCAN] ->
[1:1 SCAN] -> [USER ASPECT]
* [USER ASPECT]: User can adjust width and
height of the display.
* Check “7. Other Functions [1] User Aspect”
for more information.
• [ASPECT] Button/Lamp
- Used to change the various display ratio.
Activates in order of [16:9] -> [4:3] -> [2.35:1] ->
[1.85:1] -> [15:9] -> [16:10] -> [ANAMORPHIC
1.3X] -> [ANAMORPHIC 1.5X] -> [ANAMORPHIC
1.8X] -> [AUTO]
• [MARKER] Button/Lamp
- Used to activate/deactivate the Marker.
The type of marker at work can be selected on
the main menu.
• [H/V DELAY] Button/Lamp
- Used to check horizontal sync and vertical
sync simultaneously by moving the display
left, right, up and down.
- In this mode, the brightness of the image
automatically increase for easy verification of
synchronized signals.
• [BLUE]/[MONO] Button/Lamp
- Activates in the order of [Off]-[Blue Only]-
[Mono]-[Off]
- Press the button to remove red and green
from the input signal and display the screen
only under a blue signal. Press the button
again to activate mono mode.
• [W-FORM/VECTOR] Button/Lamp
- Used to activate/deactivate the Waveform.
- The type of Waveform at work can be selected
on the main menu.
• [F1][F2][F3] Button/Lamp
- Used to activate the [F1]~[F3] function.
* Check “6. Button Functions [5] Function Key Set
Button” for more information.
8
4K/UHD Multi-Purpose Monitor
03 CONTROLS & FUNCTIONS
FRONT
• [MENU] Button
- Used to activate the OSD menu.
- When the OSD menu is activated, press this
button to exit from the menu.
• [UP] / [DOWN] Button
- Used to move within the menu when the OSD
menu is activated and is also used to increase
or decrease the value of selected feature.
• [ENTER] Button
- Used to select the feature of main menu and
the sub menus.
• [POWER] Switch
- Used to turn the power on and off.
• [POWER INDICATOR] Lamp
- Indicates condition and power status of unit.
- Light turns off when the power is disconnected.
- Standby mode is indicated by a red LED light.
- Normal (active) mode is indicated by a Green
LED light.
- The Green light turns off when the monitor is
Normal(active) mode without input signal.
• [TALLY] Lamp
- Tally lamp that can be toggled in green or
red using the REMOTE(RJ-45) port or RS-422
serial communication.
• [APERTURE] Knob
- Used to adjust the picture sharpness.
- The value is selectable between -12 ~ 12.
• [BRIGHT] Knob
- Used to adjust the degree of brightness.
- The value is selectable between -100 ~ 100.
• [CHROMA] Knob
- Used to adjust the saturation of the image.
- The value is selectable between -50 ~ 50.
• [CONTRAST] Knob
- Used to adjust the contrast.
- The value is selectable between -100 ~ 100.
• [VOLUME] Knob
- Used to adjust the volume for internal speaker
and external output.
- The value is selectable between 0 ~ 30.
9
4K/UHD Multi-Purpose Monitor
03 CONTROLS & FUNCTIONS
REAR
• [SDI IN-A (12G)] (BNC)
- 12G/HD/SD SDI signal input
• [SDI IN-B (3G)] (BNC)
- HD/SD SDI signal input
• [SDI IN-C / SDI OUT] (BNC)
- HD/SD SDI signal input(for Quad-Link 4K/UHD
input) or 12G/HD/SD SDI Through Out for
SDI A input
• [SDI IN-D / SDI OUT] (BNC)
- HD/SD SDI signal input(for Quad-Link 4K/UHD
input) or 12G/HD/SD SDI Through Out for
SDI B input
• [HDMI IN]
- HDMI signal input
• [RS-422 IN/OUT]
- Used for the control of the monitor with
protocol provided by TVLogic or for Dynamic
UMD function by TSL protocol.
• [AUDIO IN] (Phone Jack)
- Insert the external stereo audio signal.
• [AUDIO OUT] (Phone Jack)
- The audio signal which is disembedded from
SDI or HDMI input signal or the external audio
signal which is inserted to [AUDIO IN] is output
through the phone jack.
• USB
- This terminal is used to upgrade the firmware
or color calibration made by TVLogic.
• REMOTE (RJ-45)
- Used to form a parallel switch and control the
monitor externally.
- Features can be changed in the [SYSTEM / GPI /
UMD] section of OSD menu.
• DC IN (XLR, 4 pins)
- DC power input terminal for DC 12V/24V.
* When using a DC Adapter other than the one
supplied by the manufacturer, please be
advised that the adapter with DC 12V/3A ~ 6A
can be compatible with the monitor.
DC IN socket
1: GND
4: +12V/
+24V
4
1
3
2
<WARNING!!>
When using the product make sure to ground, whenever possible, before connecting the input signal cable in order to prevent any possible damage to the product or connected devices. The damage may include signal noise, malfunction of main board or display panel.
And the connected devices such as camera or video source player may also be influenced through signal cable. Please check if the AC power source and the power extender or power distributor is grounded.
10
04 MENU TREE & ADJUSTMENT
MENU TREE & MENU CONTROL & MENU CONTROL SEQUENCE
4K/UHD Multi-Purpose Monitor
[1] MENU TREE
• OSD(On-Screen Display) Menu helps to use
various different functions.
• This Picture is the menu structure for LUM-095G.
PICTURE 같이
BRIGHTNESS
CONTRAST
CHROMA
SHARPNESS
PEAKING BOOST
KNOB LOCK
3DLUT LOAD
3DLUT SYNC
3DLUT IMPORT 1
3DLUT IMPORT 2
3DLUT IMPORT 3
UNLOCK
REC 709
SYNCHRONIZATION
NONE 1
NONE 1
NONE 1
LUM-095G
+90
+90
+40
0
0
[3] MENU CONTROL SEQUENCE
• Menu control sequence follows the order below.
1. Press MENU button to activate the OSD menu.
2. Move to a desired menu using the Knob.
3. Press the Knob to select a menu and move to
select a sub-menu by scrolling the Knob.
4. Press the Knob to select the desired sub menu.
(The selected sub-menu will be highlighted)
5. Press the ENTER button or the MENU button
to save the new value after adjusting the value
by scrolling the Knob.
6. Press MENU button to return to previous menu
and if there is no previous menu, the OSD menu
will be removed from the screen.
[2] MENU CONTROL
• User may control various functions using the
MENU button and the Knob on the top of the
monitor.
11
4K/UHD Multi-Purpose Monitor
05 MENU OPERATIONS
[1] PICTURE
PICTURE 같이
BRIGHTNESS
CONTRAST
CHROMA
SHARPNESS
PEAKING BOOST
KNOB LOCK
3DLUT LOAD
3DLUT SYNC
3DLUT IMPORT 1
3DLUT IMPORT 2
3DLUT IMPORT 3
UNLOCK
REC 709
SYNCHRONIZATION
NONE 1
NONE 1
NONE 1
LUM-095G
+90
+90
+40
0
0
• BRIGHTNESS
- Used to set the brightness(=offset) level from
-100 to 100.
* Brightness can be adjusted by using [UP] and
[DOWN] button on the front of the monitor.
• CONTRAST
- Used to set the contrast(gain) level from
-100 to 100.
* Contrast can be adjusted by using [UP] and
[DOWN] button on the front of the monitor.
• CHROMA
- Used to set the saturation level from -50 to 50.
* Chroma can be adjusted by using [UP] and
[DOWN] button on the front of the monitor.
• SHARPNESS
- Used to set the Sharpness level from 0 to 24.
* Sharpness can be adjusted by using [UP]
and [DOWN] button on the front of the
monitor.
• PEAKING BOOST
- Used to set the Peaking Boost level from 0 to 24.
* Peaking Boost can be adjusted by using
[UP] and [DOWN] button on the front of
the monitor.
• KNOB LOCK
- Locks the Knob control.
• 3DLUT LOAD
- Used to apply the internally stored 3DLUT.
- Maximum 3 x 3DLUT files can be stored.
- The file name can be set up to 20 characters
including the extension.
• 3DLUT SYNC
- Used to load a list of available 3DLUT files
currently stored in the FLASH MEMORY.
- Available 3DLUT formats are Cube, GV Lut,
Quantel, Davinci and Assimilate Scratch.
- Available sizes of the 3DLUT are 17 or 33.
• 3DLUT IMPORT 1/2/3
- Used to save the 3DLUT stored in the external
memory to the internal memory 1/2/3 area.
- Once saved, the 3DLUT can be maintained even
when the power is turned ON/OFF.
- The file name can be set up to 20 characters
including the extension.
12
4K/UHD Multi-Purpose Monitor
05 MENU OPERATIONS
[2] COLOR
COLOR 같이
STANDARD
VIDEO RANGE
PEAK LUMINANCE
BLACK LEVEL
COLOR GAMUT
COLOR TEMP
EOTF
LOCAL DIMMING
EETF
HLG SG
SG
CAM LUT
UHD
LIMITED109
100
0.001
BT.2020
6500K
2.4
OFF
OFF
OFF
OFFc
LUM-095G
PAGE (1/2)
• STANDARD
- Used to select the color and dynamic range of
the screen.
- Available options are HD, UHD, DCI-P3, PQ, HLG,
SLog3 and User1/2/3.
• VIDEO RANGE
- Used to select the range of digital video signal.
- [FULL]: Input signal 1~254(8bit), 4~1019(10bit)
- [LIMITED109]: Input signal Y': 16~254, CbCr:
16~240(8bit) / Y': 64~1019, CbCr: 64~1019(10bit)
*Activates only in [STANDARD - USER 1/2/3] mode.
• PEAK LUMINANCE
- Used to select the Peak Luminance of the
monitor.
- Selectable levels are [100] ~ [1000] with 100
increment, [1000] ~ [10000] with 1000 increment.
*Activates only in [STANDARD - USER 1/2/3] mode.
• BLACK LEVEL
- The minimum black level of the video signal
can be set differently depending on the
performance of the monitor or the lighting
environment.
- Available modes are from [0.000] to [0.010] with
0.001 increment, from [0.010] to [0.100] with
0.010 increment, from [0.100] to [0.900] with
0.100 increment.
* Activates only in the User1/2/3 mode.
• COLOR GAMUT
- Used to select the standard color gamut.
- Available options are BT709, DCI, BT2020,
NATIVE.
* Activates only in [STANDARD - USER 1/2/3]
mode.
• COLOR TEMP (Color Temperature)
- Controls the color temperature.
- Available options are 6500K, 9300K, USER 1/2/3.
* Activates only in [STANDARD - USER 1/2/3]
mode.
• EOTF (Electro-Optical Transfer Function)
- Electrophotic conversion Functions(ex: Gamma
or HDR curve).
- Available modes are 2.2, 2.4, 2.6, PQ, HLG and
SLOG3.
* Activates only in [STANDARD - USER 1/2/3]
mode.
• LOCAL DIMMING (* Not Supported)
- Used to set the Local Dimming Backlight mode.
- This mode is supported by the local dimming
backlight model and does not support F-7HS.
13
4K/UHD Multi-Purpose Monitor
05 MENU OPERATIONS
[2] COLOR
COLOR 같이
STANDARD
VIDEO RANGE
PEAK LUMINANCE
BLACK LEVEL
COLOR GAMUT
COLOR TEMP
EOTF
LOCAL DIMMING
EETF
HLG SG
SG
CAM LUT
UHD
LIMITED109
100
0.001
BT.2020
6500K
2.4
OFF
OFF
OFF
OFF
LUM-095G
PAGE (1/2)
• EETF (Electrical-Electrical Transfer Function)
- Used to display the HDR image(without clipping)
within the actual luminance range (black level
and peak luminance) that the monitor can
express. In the ON mode, the HDR image is
converted within the range of set peak luminance
and black level. In the OFF mode, the video
signal outside of the set range is clipped.
- Available modes are OFF and ON.
- Available only when the EOTF is set to PQ or
SLOG3.
* Activates only in [STANDARD - USER 1/2/3]
mode.
• HLG SG (HLG System Gamma)
- Used to set the System Gamma of HLG mode.
- In the ON mode, the value of the System
Gamma changes automatically according to the
previously set peak luminance. When it is OFF,
the value is set to default value of 1.2.
* Activates only when the EOTF is set to HLG.
and STANDARD is set to USER 1/2/3.
• SG (System Gamma)
- The System Gamma of HLG is automatically
calculated and displayed according to the set
[PEAK LUMINANCE].
- Activates only when the EOTF is set to HLG and
the HLG SG is ON.
PEAK LUMINANCE
100
200
300
400
500
600
700
800
900
1000
2000
3000
4000
5000
6000
7000
8000
9000
10000
SG (System Gamma)
0.78
0.91
0.98
1.03
1.07
1.11
1.13
1.45
1.49
1.53
1.55
1.16
1.18
1.20
1.33
1.40
1.58
1.60
1.62
• CAM LUT (Camera LUT)
- Used to change the Camera LUT.
- Available LUTs are LOG-C, C-LOG, S-LOG1,
S-LOG2, S-LOG3, REDGAMMA3, REDGAMMA4.
* Activates only when STANDARD is set to USER
1/2/3], and EOTF is set to 2.2, 2.4, 2.6.
14
4K/UHD Multi-Purpose Monitor
05 MENU OPERATIONS
[2] COLOR
COLOR 같이
COLOR TEMP
GAIN RED
GAIN GREEN
GAIN BLUE
BIAS RED
BIAS GREEN
BIAS BLUE
COLOR COPY
COLOR SPACE
6500K
6500K
BT.709
LUM-095G
+ 0
+ 0
+ 0
+ 0
+ 0
+ 0
• COLOR COPY
- Used to copy the R/G/B Gain value of pre-stored
color temperature settings.
- In User mode, find and select the color
temperature and press the Knob to copy and
apply the Gain value to GAIN RED, GAIN GREEN,
GAIN BLUE.
* Available only in User 1/2/3 mode.
• COLOR SPACE
- Used to select the standard color space.
- Available options are BT.709, DCI, BT.2020,
NATIVE.
PAGE (2/2)
• COLOR TEMP
- Controls the color temperature and allows
instant access to preset the color temperature
settings.
- Available color temperatures are 6500K, 9300K
and User1/2/3.
* In User 1/2/3 modes, user can define custom
RGB GAIN, BIAS (=Offset) and Color Copy values.
• GAIN RED / GREEN / BLUE
- Used to set Red/Green/Blue Gain (or Picture,
Contrast) level from -256 to 255.
* Available only in User 1/2/3 mode.
• BIAS RED / GREEN / BLUE
- Used to set Red/Green/Blue Bias (or Offset,
mainly affects on Black level) from -100 to 100.
* Available only in User 1/2/3 mode.
15
4K/UHD Multi-Purpose Monitor
05 MENU OPERATIONS
[3] MARKER
MARKER 같이
ENABLE
MARKER
CENTER MARKER
SAFETY AREA
FIT MARKER
MARKER MAT
MARKER COLOR
THICKNESS
USER MARKER H1
USER MARKER H2
USER MARKER V1
USER MARKER V2
GRID ENABLE
GRID TYPE
GRID THICKNESS
GRID TRANS
ON
OFF
OFF
OFF
OFF
OFF
WHITE
2
OFF
OFF
1
OFF
LUM-095G
+ 0
+1920
+ 0
+1080
• ENABLE
- Used to activate the Marker function.
• MARKER
- Available Marker types are OFF, 16:9, 4:3, 4:3 ON
AIR, 15:9, 14:9, 13:9, 1.85:1, 2.35:1, 1.85:1& 4:3 and
USER.
• CENTER MARKER
- Displays the Center Marker on the screen.
• SAFETY AREA
- Used to select and controls the size and
availability of the Safety Area.
- Available sizes are 80%, 85%, 88%, 90%, 93%,
100%, EBU ACTION 16:9, EBU GRAPHIC 16:9, EBU
ACTION 14:9, EBU GRAPHIC 14:9, EBU ACTION 4:3
and EBU GRAPHIC 4:3.
• FIT MARKER
- Used to activate or inactivate the Fit Marker
function.
- When the Marker type is selected in the Marker
menu, a border line of the Safety Area will be
displayed inside the Marker. Images below show
the difference between Fit Marker ON and OFF.
• MARKER MAT
- Used to set the darkness level outside of the
MARKER area from OFF(transparent) to 7(Black).
- The bigger the value, the darker the color.
MARKER : 4:3
SAFETY AREA : 90%
FIT MARKER : OFF
MARKER : 4:3
SAFETY AREA : 90%
FIT MARKER : ON
• MARKER COLOR
- Used to set the color of the MARKER lines.
- Available colors are WHITE, YELLOW, CYAN,
GREEN, MAGENTA, RED, BLUE, BLACK.
• THICKNESS
- Used to set the thickness of the MARKER lines.
- Thickness level is from 1 to 7 by the pixel unit.
• USER MARKER H1
- Used to set the position of the first horizontal
marker line.
- Displayed when the MARKER menu is set to
USER.
• USER MARKER H2
- Used to set the position of the second horizontal
marker line.
- Displayed when the MARKER menu is set to
USER.
• USER MARKER V1
- Used to set the position of the first vertical
marker line.
- Displayed when the MARKER menu is set to
USER.
• USER MARKER V2
- Used to set the position of the second vertical
marker line.
- Displayed when the MARKER menu is set to
USER.
• GRID ENABLE
- Used to activate the GRID lines.
• GRID TYPE
- Available grid types are 3X3, 4X4, 5X5, 6X6.
• GRID THICKNESS
- Used to set the thickness of the grid lines.
- Thickness level is from 1 to 5 by the pixel unit.
• GRID TRANS
- Used to set the transparency level of the grid lines.
- [ON]: transparent
- [OFF]: opaque
16
4K/UHD Multi-Purpose Monitor
05 MENU OPERATIONS
[4] DISPLAY / VIDEO
VIDEO 이
SCAN
ASPECT
H/V DELAY
BLUE ONLY
USER ASPECT HOR
USER ASPECT VER
3G FORMAT
H/V FLIP
ZOOM
ZOOM SPLIT
CCAPTION
CC INFO
CHANNEL (608)
SERVICE (708)
ZERO SCAN
AUTO
OFF
OFF
NORMAL
OFF
OFF
OFF
OFF
CC 1
SERVICE 1
LUM-095G
+1920
+1080
PAGE (1/2)
• SCAN
- Used to change the Scan mode.
- Available modes are ZERO SCAN, OVER SCAN,
1 : 1 SCAN, USER ASPECT
* [1 :1 SCAN] : When the UHD(3840x2160) or
4K(4096 x 2160) image is fed, this function
displays the image pixel to pixel on the screen
whose panel resolution is 1920 x 1080.
See section "7. Other Functions [1] 1 : 1 SCAN
* [USER ASPECT] : User can control the aspect
ratio by adjusting width and height of the display.
• ASPECT
- Used to change the Aspect Ratio.
- Regardless of the original Aspect ratio of the
input signal, the Aspect Modes are changed as
follow sequence. : [Auto][16:9][4:3][2.35:1][1.85:1]
[15:9][16:10][Anamorphic1.3x][Anamorphic1.5x]
[Anamorphic1.8x]
* [Auto] mode enables the Aspect Ratio of the
output signal to be synchronized to the original
Aspect Ratio of the input signal.
• H/V DELAY
- Used to monitor the Blanking area of H sync and
V sync.
• BLUE ONLY
- Available modes are [OFF] [BLUE ONLY] [MONO].
- [BLUE ONLY] : Remove red and green components
from the input signal and display blue componet
only.
- [MONO] : Used to remove the color(Chroma) from
the input signal and display the monochrome
component only.
• USER ASPECT HORIZONTAL/USER ASPECT
VERTICAL
- Activated only when the [SCAN] mode is set to
[User Aspect].
- User can adjust the Horizontal and Vertical size
of the screen.
- See section “7. Other Functions [2] User Aspect"
for more information.
17
4K/UHD Multi-Purpose Monitor
05 MENU OPERATIONS
[4] DISPLAY / VIDEO
VIDEO 이
SCAN
ASPECT
H/V DELAY
BLUE ONLY
USER ASPECT HOR
USER ASPECT VER
3G FORMAT
H/V FLIP
ZOOM
ZOOM SPLIT
CCAPTION
CC INFO
CHANNEL (608)
SERVICE (708)
ZERO SCAN
AUTO
OFF
OFF
NORMAL
OFF
OFF
OFF
OFF
CC 1
SERVICE 1
LUM-095G
+1920
+1080
PAGE (1/2)
• 3G FORMAT
- Used to select 3G-SDI A/B input format.
[NORMAL]
[A 444 10BIT YCbCr], [A 444 10BIT RGB]
[A 444 12BIT YCbCr], [A 444 12BIT RGB]
[A 422 12BIT YCbCr], [B 444 10/12BIT YCbCr]
[B 444 10/12BIT RGB], [B 422 12BIT YCbCr]
[B 422 10BIT YCbCr 60P]
- In NORMAL MODE, automatically detected when
Payload signal is contained.
• H/V FLIP
- Allows the displayed image to be flipped
horizontally or vertically.
- This feature provides flexible mounting options
for camera operators.
- Activates in the order : [H Flip]-[V Flip]-[H/V Flip]-
[AUTO]
- In the [AUTO] mode, the vertical FLIP operates
automatically according to the position of the
unit.
• ZOOM
- Used to magnify the image up to 90% on a pixel
basis and display on full screen.
- ZOOM range is 10% to 90% by 10% increment.
* ex) 10% Zoom : If the input signal’s resolution is
1920 x 1080, only 90% (1728(H) x 972(V)) of the
image would be shown on full screen without
the remaining 10% (192(H) x 108(V)) of the image.
* See section “7. Other Functions [5] Zoom" for
more information.
• ZOOM SPLIT
- Used to magnify the image.
- Used to zoom the specified area sequentially.
- Designable areas are Left-Top, Right-Top, Left-
Bottom, Right-Bottom and Center.
• CCAPTION (Closed Caption)
- This function controls the Closed Caption.
- Available modes are ANC(608), LINE21(60.8),
ANC(708).
- Captions which meet the standard of '608 :
CEA-608-B' and '708 : CEA-708-C' are only
displayed on the screen.
• CC INFO (Closed Caption Infomation)
- Displays the Closed Caption information which
the monitor currently receives.
• CHANNEL (608)
- Sets the channel of Closed Caption 608.
- Available modes are CC 1 to CC 4.
• SERVICE (708)
- Sets the service of Closed Caption 708.
- Available modes are SERVICE 1 to SERVICE 6.
18
4K/UHD Multi-Purpose Monitor
05 MENU OPERATIONS
[4] DISPLAY / VIDEO
VIDEO 이
DSLR SEL
DSLR SCALE
TIMECODE
FOCUS ASSIST
FOCUS AS COLOR
FOCUS AS LEVEL
ARRI CAM STATUS
LDS INFO
INDEX LETTER
CANON 7D
O
OFF
OFF
RED
OFF
OFF
OFF
LUM-095G
+ 90
PAGE (2/2)
• DSLR SEL
- Select the DSLR camera to be used with the
monitor. Available mode is [CANON 7D].
* DSLR cameras’ screen size and aspect ratio of
Live / Record / Playback modes vary depending
to their manufacturer.
• DSLR SCALE
- This is a special function for CANON/NIKON
DSLR cameras.
- Used to scale the image with the different
resolution as to the operation mode of the
camera to fill the screen fully.
- Available modes are LIVE/REC FULL, LIVE/REC
16:9, PLAYBAKC.
• TIMECODE
- Used to set the Time Code.
- Available modes are VITC (UP), VITC (DOWN),
LTC (UP), LTC (DOWN).
• FOCUS ASSIST
- Focus Assist helps the shooters to easily find
out the exact area in the picture with good focus,
simply by adding colors on the shape or
boundaries of the object in the picture.
- Activates in order of [Mono On]-[Color On]-[Off].
* [Color On] : Only the boudary of the area with
good focus is displayed with the designated
color.
* [Mono On] : The boundary of the area with good
focus is colored with the designated color, while
the rest of the areas(pixels) have only Y’(Luma)
signals to be black & white image.
* See section “7. Other Functions [7] Focus Assist”
for more information.
• FOCUS AS COLOR (Focus Assist Color)
- Used to select a color for Focus Assist among
RED, GREEN, BLUE, WHITE.
- This feature is available only when the Focus
Assist mode is activated.
• FOCUS AS LEVEL (Focus Assist Level)
- Used to set the edge difference value between
the edges in an image.
- Available values are from 0 to 100. Larger the
value the more sophisticated the detail detection.
- Designated color is displayed when the difference
of the edges exceeds the previously set value.
- This feature is available only when the FOCUS
ASSIST mode is activated.
• ARRI CAM STATUS (ARRI Camera Status)
- Used to display the camera status information
provided by ARRI ALEXA camera on the OSD.
- When the Arri Cam Status is activated, the
screen is squeezed to the 1742 x 980 resolution.
• LDS INFO (Lens Data System Information)
- Used to se set the information display of the Lens
Data System.
• INDEX LETTER
- Used to set the monitor identification character
notation in the upper right corner of the screen.
19
4K/UHD Multi-Purpose Monitor
05 MENU OPERATIONS
[5] WAVEFORM
WAVEFORM
ENABLE
TYPE
INTENSITY
TRANS
SIZE
LINE WAVEOFORM
SEL LINE POS
LUMA CHECK
LUMA ADJUST
RANGE ERROR
Y MAX
Y MIN
C MAX
C MIN
Y PICTURE BLINK
C PICTURE BLINK
OFF
OFF
OPAQUE
SAMLL
OFF
OFF
OFF
OFF
OFF
LUM-095G
1
• ENABLE
- Used to activate/ deactivate the Waveform
which is selected in the Type menu.
• TYPE
- This function sets the Waveform and Vectorscope.
- Available options are different according to the
Input signal.
- Activates in the order: Waveform
- Vectorscope - Waveform Wide - Waveform YCbCr
- Waveform RGB - Wave Vector - YCbCr Vector
- Full Waveform - Full Vector - Off.
• INTENSITY
- Used to set the brightness level of the Waveform/
Vectorscope display from 1 to 63.
- The higher the number the brighter the
waveform will be.
• TRANS (Transparency)
- Used to select the transparency option of the
Waveform/ Vectorscope between OPAQUE and
TRANS.
- Even though the option is set to [Opaque], it
will automatically turn to [Trans] when the
main OSD overlaps the waveform/vectorscope.
And turns back to [Opaque] when the main OSD
disappears.
0
0
0
0
0
0
• SIZE
- Adjust the size of the Waveform or Vectorscope.
- Available options are [SMALL] and [LARGE].
* See section “7. Other Function [2] Waveform /
Vectorscope“ for more information.
• LINE WAVEFORM
- This item is utilized to display one line data on
the Waveform.
• SEL LINE POS (Select Line Position)
- Used to select specific horizontal line for
Waveform / Vectorscope.
- This is available when LINE Waveform is activated.
- Use the Up and Down button to select a desired
vertical line.
- Control range varies according to the resolution
of the input SDI signal.
* PAL : Min. 1, Max. 625
* NTSC : Min. 1, Max. 525
* 720p : Min. 1, Max. 750
* 1080i : Min. 1, Max. 1125
* 1080p : Min. 1, Max. 1125
• LUMA CHECK
- Analyzes the Luma(Y’) level of the input image
and displays the selected zone on the screen.
- Available modes are [Color Pattern] and
[Zebra Pattern].
- After each pixel’s Y’ level is analyzed, it is
displayed as a certain color or zebra pattern
according to the Index on the right side of the
screen.
- When a pixel’s Y’ level is under 0%(16), the pixel
is displayed as green color or green diagonal
lines, and over 100%(235) as red color or red
diagonal lines.
- When the Y’ level of a pixel is between 0~100%,
the pixel is displayed as Gray level, except for
selected Luma Zone.
- In the [Color Pattern] mode, the zone the user
adjusted is displayed as Yellow (10% lower zone),
Pink (±2.5%), Cyan (10% upper zone).
- In the [Zebra Pattern] mode, ±5% of the selected
Y’ Level will be displayed as diagonal lines.
20
4K/UHD Multi-Purpose Monitor
05 MENU OPERATIONS
[5] WAVEFORM
WAVEFORM
ENABLE
TYPE
INTENSITY
TRANS
SIZE
LINE WAVEOFORM
SEL LINE POS
LUMA CHECK
LUMA ADJUST
RANGE ERROR
Y MAX
Y MIN
C MAX
C MIN
Y PICTURE BLINK
C PICTURE BLINK
OFF
OFF
OPAQUE
SAMLL
OFF
OFF
OFF
OFF
OFF
LUM-095G
1
• LUMA ADJUST
- Used to set the Y’ level to be colored Yellow, Pink
and Cyan in [Color Pattern] mode, or to set Y’
level zone to be displayed with diagonal lines in
[Zebra Pattern] mode simply by pushing the Up
and Down button.
- Available values are 0% ~ 100%.
* See section “7. Other Function [6] Luma(Y’) Zone
Check” for more information.
• RANGE ERROR
- Used to set whether or not to activate Y MAX,
Y MIN, C MAX, C MIN, Y PICTURE BLINK and C
PICTURE BLINK functions.
- The values of Y MAX, Y MIN, C MAX, C MIN are
indicated in Waveform/Vectorscope.
- If [Y PICTURE BLINK] or [C PICTURE BLINK] is
enabled, the section of image that exceeds the
selected values of Y MAX, Y MIN, C MAX and C
MIN shall blink.
* See section “7. Other Function [8] Range Error”
for more information.
0
0
0
0
0
0
• Y MAX
- Used to set the maximum Luma(Y’) level from 0
to 255.
- Pixels with values exceeding the maximum
luma(Y’) level blink on the screen, and are
displayed in red on the Waveform.
• Y MIN
- Used to set the minimum Luma(Y’) level from 0
to 255.
- Pixels with values below the minimum luma(Y’)
level blink on the screen, and are displayed in
red on the Waveform.
• C MAX
- Used to set the maximum chroma(C’) level from
0 to 255.
- Pixels with values exceeding the maximum
chroma(C’) level blink on the screen, and are
displayed in red on the Waveform.
• C MIN
- Used to set the minimum chroma(C’) level from
0 to 255.
- Pixels with values below the minimum chroma(C’)
level blink on the screen, and are displayed in red
on the Waveform.
• Y PICTURE BLINK
- Used to set whether or not to blink pixels with
values exceeding Y MAX and Y MIN.
• C PICTURE BLINK
- Used to set whether or not to blink pixels with
values exceeding C MAX and C MIN.
21
4K/UHD Multi-Purpose Monitor
05 MENU OPERATIONS
[6] AUDIO
AUDIO
VOLUME
Em. AUD LEFT
Em. AUD RIGHT
LEVEL METER
ALM DISPLAY
ALM REFERENCE
ALM SIZE
PEAK DECAY TIME
CH 01
CH 02
OFF
PAIR
-18 dB
SMALL
LUM-095G
+ 15
+ 10
• VOLUME
- Used to control the output volume for the stereo
speakers on the front of the monitor and Audio
Out(phone jack) on the back of the monitor.
- Control range is from 0 to 30.
• Em. AUD LEFT (Audio Left)
- Used to set the embedded audio channel for
the left speaker on the front or the left audio
out of Audio Out terminal on the back of the
monitor.
- Available options are CH01 to CH16.
*In the HDMI mode, LEFT is set to CH01.
• Em. AUD RIGHT(Audio Right)
- Used to set the embedded audio channel for
the right speaker on the front or the right
audio out of Audio Out terminal on the back
of the monitor.
- Available options are CH01 to CH16.
*In the HDMI mode, RIGHT is set to CH02.
• LEVEL METER
- Used to set the Level Meter for the embedded
audio.
- Available options are :
SDI Input : [Off]-[16CH(Hor.)]-[16CH(Ver.)]
HDMI Input: [Off]-[2CH(Hor.)]-[2CH(Ver.)]
* 16CH(HOR.) : Displays 8 channels on top
left and 8 channels on top right of the screen
horizontally.
* 16CH(VER.) : Displays 8 channels on center
left and 8 channels on top right of the screen
vertically.
* In the HDMI mode, only 2 channels are
displayed.
• ALM DISPLAY (Audio Level Meter Display)
- Used to set the display method for audio level
meter.
- Available modes are GROUP and PAIR.
* In the HDMI mode, the mode is set to PAIR.
• ALM REFERENCE (Audio Level Meter Reference)
- Display the default audio level meter value,
- Available options are -18dB and -20dB.
- Audio level meter within selected value turns to
green and exceeded audio level is displayed in
yellow.
- Audio level exceeding -4dB is displayed in red.
• ALM SIZE (Audio Level Meter Size)
- Used to control the size of the audio level meters.
- Available options are SMALL and LAGRE.
• PEAK DECAY TIME
- Sets the reduction time for max value indication
of audio signals.
- Control range is from MIN 0 to MAX 100. Bigger
number means a longer display time for max
value.
22
4K/UHD Multi-Purpose Monitor
05 MENU OPERATIONS
[7] SYSTEM / GPI / UMD
SYSTEM / GPI / UMD
DEFAULT
LUMINANCE
INTERNAL PAT
DISPLAY ENABLE
ECO SAVING
SW UPGRADE
OFF
OFF
ON
ON
OFF
VERSION
SERIAL NUM
LUM-095G
+ 100
SW 04 FPGA 01 BD 06 U
00000000
• DEFAULT
- Used to initialize OSD values to factory default.
- Available modes are DEFALUT and FACTORY.
- In the DEFALUT mode, except for the stored 3D
LUT, all values are initialized.
- In the FACTORY mode, all values are initialized to
factory default.
• LUMINANCE
- Used to indicate the current Luminance value .
- In the case of System Default, the value returns
to factory default(after color calibration).
- Available values are from 1 to 200.
• INTERNAL PAT (INTERNAL PATTERN)
- Generates Color Bar+Pludge and Grayscale
Pattern internally.
- Selectable range for Gray Pattern is from 0% to
100% with 5% increment.
* See section “7. Other Function -> [8] Internal
Pattern” for more information.
• DISPLAY ENABLE
- Used to set the LUMINANCE to the minimum
value when the time set in the still image output
is exceeded.
- When video is output or the MENU button is
pressed, the LUMINANCE is reset to the original
value.
- Settable options are ON, 5MIN, 10MIN, 20MIN
and 30MIN.
- In the Function Key, the screen can be turned
ON/OFF immediately by user’s choice.
• ECO SAVING
- Used to save power consumption automatically
when there is no monitor signal.
- When the signal is supplied, the brightness of
the monitor will be changed to the set value.
• S/W UPGRADE
- Used to upgrade the firmware using USB (Thumb
drive).
* See section “7. Other Functions -> [9] Firmware
Upgrade” for more information.
• VERSION
- Displays current firmware version.
• SERIAL NUM (Serial Number)
- Displays the serial number of the monitor.
23
4K/UHD Multi-Purpose Monitor
05 MENU OPERATIONS
[7] SYSTEM / GPI / UMD
SYSTEM / GPI / UMD
GROUP ID 0
MONITOR ID
RS-422 BAND
0
9600
PIN 1
PIN 2
PIN 3
PIN 4
PIN 5
PIN 6
PIN 7
PIN 8
HDMI
SDI A
SDI B
TALLY RED
TALLY GREEN
BLUE ONLY
POWER ON / OFF
GND
LUM-095G
• GROUP ID
- Used to group the monitors and control the
monitors by group when you control the
monitors with the protocol provided by
TVLogic, using RS-422/485 communication.
- Available setting is [0] to [98].
• MONITOR ID
- Sets the ID of each monitor for the TVLogic
control protocol or DYNAMIC UMD using
RS-422/485 communication.
- Available setting is [0] to [98].
• RS-422 BAUD
- Sets the monitor control program that TVLogic
provides and Baud rate.
- Available setting is [9600], [14400], [19200],
[38400], [115200].
• PIN 1 to PIN 8
- This item activates and inactivates the REMOTE
function.
- The user can designate a function to each pin,
and each pin's default setting is as follows.
PIN 1: HDMI
PIN 2: SDI A
PIN 3: SDI B
PIN 4: TALLY RED
PIN 5: TALLY GREEN
PIN 6: BLUE ONLY
PIN 7: POWER ON / OFF
PIN 8: GND
24
PIN NO.
PIN
1~6
Settable Functions
NONE
HDMI
SDI A
SDI B
TALLY RED
TALLY GREEN
BLUE ONLY
MONO
ASPECT
H/V DELAY
MARKER 16:9
MARKER 15:9
MARKER 14:9
MARKER 13:9
MARKER 4:3
MARKER 4:3 ON AIR
MARKER 1.85:1
MARKER 2.35:1
MARKER 1.85:1 & 4:3
MARKER CENTER
SAFETY AREA 80%
SAFETY AREA 88%
SAFETY AREA 90%
SAFETY AERA 93%
SAFETY AERA 100%
REMOTE (RJ-45)
1: Pin1
2: Pin2
3: Pin3
4: Pin4
5: Pin5
6: Pin6
7: Pin7
8: GND
1 8
4K/UHD Multi-Purpose Monitor
05 MENU OPERATIONS
[7] SYSTEM / GPI / UMD
SYSTEM / GPI / UMD
UMD ID 0
UMD DISPLAY
UMD CHARACTER
UMD CHAR COLOR
UMD B.G TRANS
UMD B.G SIZE
D-UMD TALLY TYPE
TALLY1 COLOR
TALLY2 COLOR
TALLY3 COLOR
TALLY4 COLOR
OFF
CHANNEL 1
WHITE
OPAQUE
SMALL
DEFAULT
OFF
OFF
OFF
OFF
LUM-095G
• UMD ID
- Sets the ID of the UMD.
- Available setting is [0] to [125].
• UMD DISPLAY
- Sets the UMD mode among UMD, ANC and
DYNAMIC UMD.
*UMD: Displays user customized characters on
screen.
*ANC: Displays characters embedded in SDI
signal.
*D-UMD(TSL-S8C): Displays the tally signal and
8 letters that are input by TSL protocol (V3.1)
on the screen.
*D-UMD(TSL-S16C): Displays the tally signal
and 16 letters that are input by TSL protocol
(V3.1) on the screen.
*D-UMD(TSL-D8C): Displays a pair of tally
signal and a pair of 8 letters that are input by
TSL protocol (V3.1) on the screen.
• UMD CHARACTER
- Used to customize the characters for [UMD].
- Alphabets, numbers and special symbols are
available.
- Maximum of 8 characters.
• UMD CHAR COLOR
- Sets the color of the UMD letter.
- Available mode is [WHITE], [RED], [GREEN],
[BLUE], [YELLOW], [CYAN], [MAGENTA]
• UMD B.G TRANS
- Sets the transparency of UMD letter box.
- The selectable modes are [OPAQUE], [50%],
[85%], [100%].
• UMD B.G SIZE
- Sets the font size of UMD and the size of UMD
letter box.
- The selectable modes are [SMALL] and [LARGE].
• D-UMD TALLY TYPE
- Allows for adjusting the various modes of tally
operation.
- The operation of sub menus varies depending
on the settings in [UMD DISPLAY]
*DEFAULT: Original TVLogic managing method
(VRT)
*USER COLOR: The user can set each tally color.
*CHARACTER: Shows tally in the letter color.
The operation is the same as [DEFAULT].
*B.G. COLOR: Show tally in the letter background
color. The operation is the same as [DEFAULT].
*USER TALLY: This mode receives the signal fed
as bit0 and bit1 of TSL Protocol control byte,
adjusts the color the user wants, and then
shows the tally.
Available modes are Off, White, Red, Green,
Blue, Yellow, Cyan, Magenta.
*USER CHARACTER: Shows tally in letter color.
The method is the same as USER TALLY.
*USER B.G.: Show tally in letter background
color. The method is the same as USER TALLY.
• TALLY1 COLOR ~ TALLY4 COLOR
- This menu sets the color of Tally1, Tally2, Tally3,
Tally4 respectively.
- The selectable colors are Red, Green, Yellow.
• B0:0 B1:0 ~ B0:1 B0:1
B0:00 B3:00 ~ B0:11 B3:11
- This menu sets the color of the input condition
for byte0, byte1 in TSL Protocol Control Byte.
- The selectable colors are Off, White, Red, Green,
Blue, Yellow, Cyan, Magenta.
25
4K/UHD Multi-Purpose Monitor
05 MENU OPERATIONS
[7] SYSTEM / GPI / UMD
SYSTEM / GPI / UMD
UMD ID 0
UMD DISPLAY
UMD CHARACTER
UMD CHAR COLOR
UMD B.G TRANS
UMD B.G SIZE
D-UMD TALLY TYPE
TALLY1 COLOR
TALLY2 COLOR
TALLY3 COLOR
TALLY4 COLOR
OFF
CHANNEL 1
WHITE
OPAQUE
SMALL
DEFAULT
OFF
OFF
OFF
OFF
LUM-095G
• UMD DISPLAY / • D-UMD TALLY TYPE
[Sub Menu Combination Table]
DEFAULT
USER
COLOR
CHARACTER
B.G. COLOR
USER
TALLY
USER
CHARACTER
USER
B.G.
UMD
N/A
TALLY1 COLOR
TALLY2 COLOR
N/A
N/A
TALLY1 COLOR
TALLY2 COLOR
TALLY3 COLOR
TALLY4 COLOR
TALLY1 COLOR
TALLY2 COLOR
TALLY3 COLOR
TALLY4 COLOR
TALLY1 COLOR
TALLY2 COLOR
TALLY3 COLOR
TALLY4 COLOR
ANC
N/A
TALLY1 COLOR
TALLY2 COLOR
N/A
N/A
TALLY1 COLOR
TALLY2 COLOR
TALLY3 COLOR
TALLY4 COLOR
TALLY1 COLOR
TALLY2 COLOR
TALLY3 COLOR
TALLY4 COLOR
TALLY1 COLOR
TALLY2 COLOR
TALLY3 COLOR
TALLY4 COLOR
UMD DISPLAY
D-UMD(TSL-SBC) D-UMD(TSL-S16C) D-UMD(TSL-D8C)
N/A N/A
TALLY1 COLOR
TALLY2 COLOR
N/A
N/A
B0-B1 : 00
B0-B1 : 01
B0-B1 : 10
B0-B1 : 11
B0-B1 : 00
B0-B1 : 01
B0-B1 : 10
B0-B1 : 11
B0-B1 : 00
B0-B1 : 01
B0-B1 : 10
B0-B1 : 11
TALLY1 COLOR
TALLY2 COLOR
N/A
N/A
B0-B1 : 00
B0-B1 : 01
B0-B1 : 10
B0-B1 : 11
B0-B1 : 00
B0-B1 : 01
B0-B1 : 10
B0-B1 : 11
B0-B1 : 00
B0-B1 : 01
B0-B1 : 10
B0-B1 : 11
N/A
TALLY1 COLOR
TALLY2 COLOR
TALLY3 COLOR
TALLY4 COLOR
N/A
N/A
B0-B3 : 0000
B0-B3 : 0101
B0-B3 : 1010
B0-B3 : 1111
B0-B3 : 0000
B0-B3 : 0101
B0-B3 : 1010
B0-B3 : 1111
B0-B3 : 0000
B0-B3 : 0101
B0-B3 : 1010
B0-B3 : 1111
26
4K/UHD Multi-Purpose Monitor
05 MENU OPERATIONS
[7] SYSTEM / GPI / UMD
Tally1
<Dynamic UMD Protocol (TSL V3.1)>
* Transmission (18 Byte) (PC or Device -> Monitor)
HEADER
(1 BYTE)
CONTROL
BYTE(1 BYTE)
DISPLAY DATA
(16 BYTE)
* [HEADER] : Display address (0~126) + 80 hex.
* [CONTROL BYTE]
bit 0 : Tally 1 (1=on, 0=off)
bit 1 : Tally 2 (1=on, 0=off)
bit 2 : Tally 3 (1=on, 0=off)
bit 3 : Tally 4 (1=on, 0=off)
bit 4 : bright data
(Not used)
bit 5 : bright data
(Not used)
bit 6 : reserved
(Not used)
bit 7 : cleared to 0
(Not used)
*
[DISPLAY DATA] : 16 displayable ASCII characters.
CHANNEL1 Tally2 Tally3 CHANNEL1 Tally4
27
4K/UHD Multi-Purpose Monitor
05 MENU OPERATIONS
[7] SYSTEM / GPI / UMD
• Tally Type - Default
- TSL_S8C(Single 8 Characters) & TSL_S16C(Single 16 Character)
Bit 1
(Tally2)
Bit 0
(Tally1)
Operation
0
0
1
1
0
1
0
1
CHANNEL1
CHANNEL1
CHANNEL1
CHANNEL1
- TSL_D8C(Dual 8 Character)
Bit 3
(Tally4)
Bit 2
(Tally3)
0 0
0 1
1
1
0
1
Operation
CHANNEL1
CHANNEL1
CHANNEL1
CHANNEL1
• D-UMD Tally Type - USER COLOR
- Allows to set the color of TALLY1 to TALLY4.
When [UMD DISPLAY] is set to [D-UMD(TSL-D8C) and [D-UMD TALLY TYPE] and [TALLY1 to
TALLY4 COLOR] are set as follows, tallies are displayed like the image below.
D-UMD TALLY TYPE USER COLOR
TALLY1 COLOR
TALLY2 COLOR
TALLY3 COLOR
TALLY4 COLOR
RED
GREEN
RED
YELLOW
CHANNEL1 CHANNEL1
28
4K/UHD Multi-Purpose Monitor
06 BUTTON FUNCTIONS
INPUT BUTTON
SOURCE INPUT
SDI A
SDI B
SDI 2SI
SDI QUAD
HDMI
3840 x 2160 50p*
*Current Input Signal Format
• The LUM-095G supports 12G/HD/SD SDI input.
1. If you push [MENU] button for more than a
second, the OSD window for the input selection
appears.
You can move to the desired input mode using
[UP] and [DOWN] button and then select it by
pusing [ENTER] button.
2. The current input signal format is displayed at
the bottom of the OSD window.
3. If you push [MENU] button once again, the OSD
window disappears.
*If the video is not displayed after the input is
selected, please check the video source and the
input cable.
SDI
SDI A
3840 x 2160 50p*
*Current Input Signal Format
• The LUM-095G has the four SDI inputs.
1. If you push [SDI] button, the input mode is
changed in the order of SDI A, SDI B, SDI 2SI,
SDI QUAD.
2. The current input signal format is displayed at
the bottom of the OSD window.
*If the video is not displayed after the input is
selected, please check the video source and the
input cable.
HDMI
HDMI
1920 x 1080 50p*
*Current Input Signal Format
• The LUM-095G has an HDMI input.
1. Please push [HDMI] button to display the HDMI
signal.
2. The current input signal format is displayed at
the bottom of the OSD window.
*If the video is not displayed after the input is
selected, please check the video source and the
input cable.
29
4K/UHD Multi-Purpose Monitor
06 BUTTON FUNCTIONS
INPUT BUTTON
SCAN BUTTON
• The LUM-095G supports the various SCAN modes
1. If you push [SCAN] button, the mode is changed
in the order of ZERO SCAN → OVER SCAN →
1 : 1 SCAN → USER ASPECT.
- Over Scan: Zooms in and out of the image to
96% of its original size without changing the
aspect ratio.
- Zero Scan: Zooms in/out of the image without
changing the aspect ratio.
- 1:1 SCAN: Display the input video by 1:1 pixel
mapping on the screen.
This feature is activated only when the resolution
of the input image is bigger than the resolution
of the LCD panel.
FUNCTION(F1/F2/F3) BUTTON
• The Function bottons allow for making a quick
setting on each button.
1. Press the Function button(F1 to F3) on the front
of the monitor for more than 2 seconds, and the
OSD menu pops up on the screen.
2. Move to a desired function using [UP] and
[DOWN] button and press the [ENTER] button to
select.
3. Once the function is set, press the Function
button (F1~F3) to activate the assigned function.
ASPECT BUTTON
• The LUM-095G supports the various Aspect ratio.
1. Press [ASPECT] button on the front of the
monitor to activate various aspect ratio.
2. If you push [ASPECT] button, the mode is changed
in the order of 16 : 9 → 4:3 → 2.35:1 → 1.85:1 →
15:9 → 16:10 → ANAMORPHIC 1.3X →
ANAMORPHIC 1.5X → ANAMORPHIC 1.8x → AUTO.
F1 FUNC. SEL
SCAN
ASPECT
MARKER
H/V DELAY
BLUE ONLY
ZOOM
ZOOM SPLIT
FREEZE
AUDIO LVM
TIME CODE
FOCUS ASSIST
WAVEFORM
LUMA(Y`) ZONE
RANGE ERROR
H/V FLIP
MAX BRIGHTNESS
CAMERA LUT
DISPLAY ENABLE
INPUT SELECT
ARRI METADATA
GRID
EXTERNAL FAN
30
4K/UHD Multi-Purpose Monitor
07 OTHER FUNCTIONS
[1] 1 : 1 SCAN
• The resolution of the LCD panel of the LUM-095G is 1920 x 1080. When the UHD(3840x2160),
4K(4096 x 2160), or SD image is fed, this function displays the image pixel to pixel on the screen.
• You can nevigate the UHD or 4K image with pixel to pixel over the 9 divided parts by pushing
[UP] and [DOWN] button.
C
L-T C-T
R-T
R-C
R-T
R-B
C-B L-B
R-T
R-B
L-C
<Original Image> <Left - Top>
<Left - Center> <Right - Bottom>
31
4K/UHD Multi-Purpose Monitor
07 OTHER FUNCTIONS
[2] USER ASPECT
• Used to adjust the Width /Height display ratio.
1. Select the [USER ASPECT] mode in the OSD menu or by pressing [SCAN] button on the front.
2. After the activation, press [UP] and [DOWN] buttons to adjust the aspect ratio.
USER ASPECT
WIDTH +1920
HEIGHT +1080
- Adjust the ratio using the Knob (UP/DOWN).
- Control range for width: 0~1920.
- Control range for height : 0~1080.
- The size-adjusted picture always stays in the center of the screen.
- The size can be adjustable with 2 increment and decrement.
32
4K/UHD Multi-Purpose Monitor
07 OTHER FUNCTIONS
[3] WAVEFORM / VECTORSCOPE
• WAVEFORM Y
- Displays the Luma(Y’) component of the input signal into waveform.
• The Waveform/ Vectorscope function can be
used only when the input signal is YUV.
• In the case of RGB input, Waveform RGB is supported.
• Available modes in the YUV signal:
- Waveform
- Vectorscope
- Waveform Wide
- Waveform YCbCr
- Waveform RGB
- Wave_Vector
- YCbCr Vector
- Full Waveform
- Full Vector
• WAVEFORM Cb, Cr
- Displays the Cb, Cr components of the input signal into waveform.
• VECTORSCOPE
- Displays the color components ‘B-Y’ and ‘R-Y’ of the input signals onto the X-Y axis.
- Two different types of Vetorscopes are displayed according to SD or HD input signals.
- 100% and 75% scales are indicated on the Vetorscope.rm.
100%
75%
33
4K/UHD Multi-Purpose Monitor
07 OTHER FUNCTIONS
[4] LINE SELECT (WAVEFORM / VECTORSCOPE)
• Used to select specific Vertical Line for WaveForm/VectorScope.
- This is available when LINE WaveForm is activated.
- To activate this feature, set [WAVEFORM] - [LINE WAVEFORM] - [ON], and select the desired horizontal
line using [UP] and [DOWN] button in [SEL LINE POS].
- Selected line is indicated in White on the screen.
- Control range varies according to the resolution of the input SDI signal.
* PAL : 0~625
* NTSC : 0~525
* 720p : 0~750
* 1080 i/p : 0~1125
- Control range for HDMI signal varies according to the output resolution of the signal.
* Selected line is indicated on the screen.
LINE POSITION
34
07 OTHER FUNCTIONS
[5] ZOOM
• Used to magnify the input signal from 0% to 90%.
• Supports Zoom Width Scroll / Zoom Height Scroll function.
• Zooms IN/OUT focused on the scrolled area.
ZOOM 0FF
WIDTH + 0
HEIGHT + 0
<ZOOM OFF>
4K/UHD Multi-Purpose Monitor
<ZOOM 30%>
• When the image is zoomed up, you can move the zoomed image vertically and horizontally with the
zoom-up rate maintaining.
ZOOM 30%
WIDTH + 0
HEIGHT + 0
ZOOM 30%
WIDTH - 70
HEIGHT - 100
35
4K/UHD Multi-Purpose Monitor
07 OTHER FUNCTIONS
[6] LUMA (Y') ZONE CHECK
• COLOR PATTERN TYPE
- Displays the pixels with the designated
Luma(Y’) levels of the input image in colors.
Pixels whose Y’ level is over 100% are displayed
as Red.
Pixels whose Y’ level is below 0% are displayed
as Green.
- Pixels with Y’ levels which are designated by the
user are displayed in following colors - yellow,
pink, cyan.
- Factory Default Y’ (Border line between pink and
yellow) level is 70%. The upper 2.5% and lower
2.5% zone from the Y’ level set in [LUMA(Y’)
ZONE ADJUST] menu is displayed in Pink.
The upper 10% zone from the Pink zone is
displayed in Yellow, and the lower 10% zone
from the Pink zone is displayed in Cyan. So, 25%
zone is displayed in colors and the other 75%
zone is displayed mono and white.
• LUMA(Y’) ZONE CHECK function is convenient
to set the exposure or the lighting so that the
skin tone or the specific color tone is correctly
shot.
• ZEBRA PATTERN TYPE
- Displays the pixels with the designated
Luma(Y’) levels of the input image in zebra
pattern. Pixels whose Y’ level is over 100% are
displayed as red diagonal stripes.
Pixels whose Y’ level is below 0% are displayed
as green diagonal stripes.
- Pixels with Y’ levels which are designated by the
user are displayed as black diagonal stripes.
- Factory Default Y’ level is 70%. The pixels with Y’
level from 65% to 75% are displayed as black
zebra pattern.
So, totally 10% zone is displayed as black
diagonal stripes.
<Luma Zone Check OFF>
<Luma Zone Check ON_Zebra Pattern Type>
36
<Luma Zone Check ON_Color Pattern Type>
4K/UHD Multi-Purpose Monitor
07 OTHER FUNCTIONS
[7] FOCUS ASSIST
• Focus Assist function assigns a color on the pixels of the shape or boundary of the image, which
helps the user easily see which part of the image is in focus or out of focus.
- With this function, the user can easily differentiate the focused area from the out-focused area
especially when shooting with a shallow depth of field.
- Available types are [COLOR ON] and [MONO ON].
• [COLOR ON]: Background image is original color type.
• [MONO ON]: Background image is mono type.
<FOCUS ASSIST - COLOR ON> <FOCUS ASSIST - MONO ON>
37
4K/UHD Multi-Purpose Monitor
07 OTHER FUNCTIONS
[8] FIRMWARE UPGRADE
• The USB (Thumb drive) which contains the F/W file is neened for Firmware Upgrade.
• Select the S/W UPGRADE in the SYSTEM menu.
1. Connect the USB to the USB Slot on the bottom of the monitor.
2. Go to [MENU] → [SYSTEM / GPI / UMD] → [SW UPGRADE], and select what to update among ALL, CPU,
FPGA, IMAGE.
3. When the USB connection is completed, the S/W upgrade starts and the progress displays on the
bottom left side of the screen.
4. If the USB doesn’t connect properly or there is no file in the specified location, the error message
will be displayed on the bottom left side of the screen and the upgrade won’t start.
5. In that case, check the USB or the file location and try again.
• After USB connection, turn off and then on the monitor.
38
4K/UHD Multi-Purpose Monitor
08 VIDEO SUPPORT RESOLUTION - SDI
Input Signal
SD-SDI
Interfaces
Single Link
Input Signal
Interfaces
HD-SDI
Single Link
Input Signal
Interfaces
3G-SDI (A/B)
Single Link
Input Signal
Interfaces
6G/12G-SDI (A)
Single Link
Input Signal
Interfaces
3G-SDI
Quad Link
Square Division
2-Sample Interleave
Signal Format
(SD-SDI)
720x487 (59.94i)
720x576 (50i)
YCbCr 4:2:2 10bit
Signal Format
(HD-SDI)
YCbCr 4:2:2 10bit 1280x720 (50/59.94/60P)
1920x1080
(23.98/24/25/29.97/30p)
(50/59.94/60I)
(24/25/29.97/30psf)
YCbCr 4:2:2 10bit
1920x1080 (60p/59.94p/50P)
Signal Format
(3G-SDI)
YCbCr 4:2:2 10bit
1920x1080
(30/29.97/25/24/23.98p)
(30sF/29.97sF/25sF/24sF/23.98sF)
(60/59.94/50i)
YCbCr 4:2:2 12bit
RGB 4:4:4 10bit / 12bit
YCbCr 4:4:4 10bit / 12bit
1280x720 (50/59.94/60P)
RGB 4:4:4 10bit
YCbCr 4:4:4 10bit
2048x1080
(60/59.94/50/30/29.97/25/24/23.98
30sF/29.97sF/25sF/24sF/23.98sF)
RGB 4:4:4 8bit / 10bit / 12bit
YCbCr 4:4:4 8bit / 10bit / 12bit
YCbCr 4:2:2 8bit / 10bit / 12bit
Signal Format
(Single Link 6G/12G SDI)
3840x2160 (30/29.97/25/24/23.98p)
4096x2160 (30/29.97/25/24/23.98p)
YCbCr 4:2:2 10bit
3840x2160 (30/29.97/25/24/23.98p)
4096x2160 (30/29.97/25/24/23.98p)
YCbCr 4:2:2 10bit
Signal Format
(Quad Link 6G/12G SDI)
3840x2160 (23.98/24/25/29.97/30p)
YCbCr 4:4:4 10bit / 12bit
RGB 4:4:4 10bit / 12bit
3840x2160 (50/59.94/60p) YCbCr 4:2:2 10bit
4096x2160 (23.98/24/25/29.97/30p)
4096x2160 (50/59.94/60p)
YCbCr 4:4:4 10bit / 12bit
RGB 4:4:4 10bit / 12bit
YCbCr 4:2:2 10bit
39
4K/UHD Multi-Purpose Monitor
08 VIDEO SUPPORT RESOLUTION - HDMI
Input Signal
Interfaces
HDMI
Single Link
Signal Format
(HDMI/DP)
480i(60) / 576i(50)
480p(60) / 576p(50)
1280x720(50/59.94/60p)
1920x1080(50/59.94/60p)
1920x1080(23.98/24/25/29.97/30p,
60i/59.94i/50i )
* HDMI
RGB 4:4:4 8bit
YCbCr 4:4:4 8bit
YCbCr 4:2:2 8bit
3840x2160
(23.98/24/25/29.97/30p/50/59.94/60p)
RGB 4:4:4 8bit / 10bit / 12bit
YCbCr 4:4:4 8bit / 10bit / 12bit
YCbCr 4:2:2 8bit / 10bit / 12bit
YCbCr 4:2:0 8bit / 10bit / 12bit
4096x2160
(23.98/24/25/29.97/30p/50/59.94/60p)
RGB 4:4:4 8bit / 10bit / 12bit
YCbCr 4:4:4 8bit / 10bit / 12bit
YCbCr 4:2:2 8bit / 10bit / 12bit
YCbCr 4:2:0 8bit / 10bit / 12bit
40
09 PRODUCT SPECIFICATIONS
4K/UHD Multi-Purpose Monitor
Specifications LUM-095G
LCD
Input & Output
Input Signal
SDI Input Signal
Formats
Remote Control
& Update
SMPTE ST-296M
SMPTE ST-260M
SMPTE ST-125M
ITU-R BT.656
1 x REMOTE
2 x RS-422
1 x USB
Audio In
Audio Out
Power
Power Consumption (Approx.)
Operating Temperature
Storage Temperature
Dimensions
Main Body
With Stand
Shipping Box
Weight (with stand)
Basic Accessories
Optional Accessories
Size
Resolution
Pixel Pitch
Color Depth
Viewing Angle
Luminance of white
Contrast
Display Area
SDI-A
SDI-B
SDI-C
SDI-D
1 x HDMI
12G-SDI
6G-SDI
3G-SDI
HD-SDI
SD-SDI
HDMI
SMPTE ST-2082
SMPTE ST-2081
SMPTE ST-425M-A/B
SMPTE ST-274M
9.0”
1920 x 1080 (16:9)
0.1035 x 0.1035 mm
16.7M Colors (True 8 bit)
178°(H) / 178°(V)
400 cd/m²
750 : 1
198.72 x 111.78 mm
12G/6G/3G/HD-SDI Input
3G/HD/SD-SDI Input
3G/HD-SDI Input (For Quad-Link 4K/UHD Input only) or
12G/6G/3G/HD-SDI Output (Passive Through Out)
3G/HD-SDI Input (For Quad-Link 4K/UHD Input only) or
3G/HD/SD-SDI Output (Passive Through Out)
HDMI 2.0
12Gb/s
6Gb/s
2.970Gb/s
1.485Gb/s
270Mbps
480i / 480p / 576i / 576p / 720p / 1080i / 1080p /2160p
2160p (60/59.94/50) (*RGB 4:4:4 not supported.)
2160p (30/29.97/25/24/23.98) (*RGB 4:4:4 not supported.)
1080p (60/59.94/50/30/29.97/25/24/23.98/30sF/29.97sF/25sF/24sF/23.98sF)
1080i (60/59.94/50)
1080i (60/59.94/50)
1080p (30/29.97/25/24/24sF/23.98/23.98sF)
720p (60/59.94/50)
1035i (60/59.94)
480i (59.94)
576i (50)
RJ-45 Input, GPI Control
RJ-45 Input & Output, Control by TVLogic Protocol
USB A type, Firmware Upgrade
Embedded Audio / Analog Stereo (Phone Jack)
Internal Speaker(Mono) / Analog Stereo (Phone Jack)
12V DC/24V DC
30 Watts(DC)/Max 2.6A
-20 °C to 40 °C (-4 °F to 104 °F )
-30 °C to 50 °C (-22 °F to 122 °F )
223 x 175 x 60 mm / 8.78 x 6.89 x 2.36 inch
260 x 194.2 x 90 mm / 10.24 x 7.65 x 3.54 inch
330 x 180 x 250 mm / 12.99 x 7.09 x 9.84 inch
2.14Kg / 4.72lb
AC Power Cord, DC Power adaptor, Handle, Stand, Camera mount
Acrylic Protector, Rack Mount Kit(Single, Dual), Carrying Bag with Hood,
Sun Hood, HDMI Bracket
*The specifications above may be changed without notice.
41
LUM
-095G

Public link updated
The public link to your chat has been updated.
Advertisement