Test Report issued under the responsibility of: NCB

Test Report issued under the responsibility of: NCB
Test Report issued under the responsibility of:
NCB TÜV SÜD PSB Pte Ltd
1 Science Park Drive,
Singapore 118221
TEST REPORT
IEC 60950-1: 2005 (2nd Edition) and/or EN 60950-1:2006
Information technology equipment – Safety –
Part 1: General requirements
Report Reference No. .....................: 081-100802-000
Date of issue .....................................:
2010-08-05
Total number of pages.......................
57
CB/CCA Testing Laboratory ..........:
TÜV SÜD Asia Ltd. Taiwan Branch
Address.............................................:
7F., No.37, Sec. 2, Zhongyang S., Rd., Beitou District, Taipei City,
11270, Taiwan.
Applicant’s name ............................:
Pegatron Corporation
Address.............................................:
5F, No. 76, Ligong St., Beitou District, 112 Taipei, Taiwan
Manufacturer’s name .....................:
Pegatron Corporation
Address.............................................:
5F, No. 76, Ligong St., Beitou District, 112 Taipei, Taiwan
Factory’s name ...............................:
See page 5 for details
Address.............................................:
See page 5 for details
Test specification:
Standard ...........................................:
IEC 60950-1:2005 (2nd Edition) and/or
EN 60950-1:2006+A11:2009
Test procedure .................................:
CB / CCA
Non-standard test method…………..:
N/A
Test Report Form No. .....................:
IECEN60950_1C
Test Report Form(s) Originator ........:
SGS Fimko Ltd
Master TRF .......................................:
Dated 2007-06
Copyright © 2007 IEC System for Conformity Testing and Certification of Electrical Equipment
(IECEE), Geneva, Switzerland. All rights reserved.
This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE
is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will
not assume liability for damages resulting from the reader's interpretation of the reproduced material due to
its placement and context.
If this Test Report Form is used by non-IECEE members, the IECEE/IEC logo and the reference to the CB
Scheme procedure shall be removed.
This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and
appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.
If this Test Report Form is used by non-CCA members, the CIG logo and the reference to the CCA
Procedure shall be removed.
This report is not valid as a CCA Test Report unless signed by an approved CCA Testing Laboratory
and appended to a CCA Test Certificate issued by an NCB in accordance with CCA
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 1 of 57
Test Report IECEN60950_1C
Test item description .................... : Tablet PC
Trade Mark ....................................... :
MEDION
Manufacturer .................................... :
Same as applicant
Model/Type reference ...................... :
S2011, S2012, S2013, S2213, S2214, S2215, TT116A01, TT116B01
Ratings ............................................. :
19 Vdc, 2.37 A
Testing procedure and testing location:
CB/CCA Testing Laboratory:
Testing location/ address ...................... :
Associated CB Laboratory:
Testing location/ address ...................... :
Tested by
(name + signature) ...................... :
Approved by
(+ signature) ................................ :
Testing procedure: TMP
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd., Beitou District,
Taipei City, 11270, Taiwan.
N/A
N/A
Mr. Watson Yang
Mr. Larry Lai
.....................................................
.....................................................
N/A
Tested by (name + signature) ..... :
Approved by (+ signature) ............ :
Testing location/ address ...................... :
Testing procedure: WMT
N/A
N/A
Tested by (name + signature) ..... :
Witnessed by (+ signature) .......... :
Approved by (+ signature) ........... :
Testing location/ address ...................... :
Testing procedure: SMT
N/A
N/A
Tested by (name + signature) ..... :
Approved by (+ signature) ............ :
Supervised by (+ signature) ........ :
Testing location/ address ................ :
N/A
Testing procedure: RMT
N/A
Tested by (name + signature) ..... :
Approved by (+ signature) ............ :
Supervised by (+ signature) ........ :
Testing location/ address ...................... :
N/A
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 2 of 57
Test Report IECEN60950_1C
Summary of testing:
Tests performed (name of test and test clause):
Testing location:
All test results were found satisfactory in
accordance with IEC 60950-1:2005 (2nd Edition)
and / EN 60950-1:2006+A11:2009.
All tests as described in Test Case and
Measurement Sections were performed at the
laboratory described on page 2.
Summary of compliance with National Differences:
National Differences for Austria (AT), Canada (CA), Germany (DE), Denmark (DK), Finland (FI), France
(FR), United Kingdom (GB), Italy (IT), Japan (JP), Korea (KR), The Netherlands (NL), Norway (NO),
Poland (PL), Sweden (SE), Slovenia (SI), United States of America (US). Group Differences as listed in the
CB Bulletin No. 112A, (December 2006) are recorded at the end of this Report.
Copy of marking plate
See attachment No. 2
( Total 2 pages )
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 3 of 57
Test Report IECEN60950_1C
Test item particulars .................................................. :
Equipment mobility .................................................... : [] movable [] hand-held
[X] transportable
[] stationary [] for building-in [] direct plug-in
Connection to the mains ............................................ : [] pluggable equipment [] type A [] type B
[] permanent connection
[] detachable power supply cord
[] non-detachable power supply cord
[Χ] not directly connected to the mains.
Operating condition ................................................... : [Χ] continuous
[] rated operating / resting time:
Access location ......................................................... : [Χ] operator accessible
[] restricted access location
Over voltage category (OVC) ................................... : [] OVC I [] OVC II [] OVC III [] OVC IV
[Χ] other: not directly connected to AC or DC mains.
Mains supply tolerance (%) or absolute mains supply N/A
values ....................................................................... :
Tested for IT power systems .................................... : [] Yes
[Χ] No
IT testing, phase-phase voltage (V) ......................... : N/A
Class of equipment ................................................... : [] Class I [] Class II
[] Not classified
[Χ] Class III
Considered current rating (A) ................................... : N/A
Pollution degree (PD) ............................................... : [] PD 1
[Χ] PD 2
[] PD 3
IP protection class .................................................... : Ordinary
Altitude during operation (m) .................................... : Up to 2000
Altitude of test laboratory (m) ................................... : below 2000
Mass of equipment (kg) ............................................ : Approx. 1.02
Possible test case verdicts:
- test case does not apply to the test object ................. : N/A
- test object does meet the requirement ....................... : P (Pass)
- test object does not meet the requirement................. : F (Fail)
Testing .......................................................................... :
Date of receipt of test item ............................................ : 2010-07-20
Date(s) of performance of tests .................................... : 2010-07-20 to 2010-08-02
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 4 of 57
Test Report IECEN60950_1C
General remarks:
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory.
"(See Enclosure #)" refers to additional information appended to the report.
"(See appended table)" refers to a table appended to the report.
Note: This TRF includes EN Group Differences together with National Differences and Special National
Conditions, if any. All Differences are located in the Appendix to the main body of this TRF.
Throughout this report a point is used as the decimal separator.
Factory:
1. ProTek (Shanghai) Ltd. ( ID No.: 61019 )
No.3768, Xiu Yan Road, Kang Qiao Town, 201319 Pu Dong New District, Shanghai,
People's Republic of China
Attachments:
Attachment No. 1
Attachment No. 2
Attachment No. 3
National Deviations
Marking Plate
Photo
19 pages
2 pages
7 pages
General product information:
The equipment is a Tablet PC for use in information technology equipment.
All models are identical except for model designation.
The external power adapter is a CB approved component, see Table 1.5.1 for details.
The external power adapter is in accordance with the Limited Power Source (Clause 2.5).
The maximum ambient temperature specified by manufacturer is 35 °C.
Unless otherwise specified, all tests were performed on model S2011 to represent the other models.
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 5 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
1
GENERAL
P
1.5
Components
P
1.5.1
General
P
Comply with IEC 60950-1 or relevant component
standard
Components which were found
to affect safety aspects comply
with the requirements of this
standard or within the safety
aspects of the relevant IEC
component standards.
(see appended table 1.5.1).
P
1.5.2
Evaluation and testing of components
Components which are certified
to IEC and/or national standards
are used correctly within their
ratings.
Components not covered by IEC
standards are tested under the
conditions present in the
equipment.
P
1.5.3
Thermal controls
No thermal control.
N/A
1.5.4
Transformers
Transformer in approved power
adaptor.
N/A
1.5.5
Interconnecting cables
Interconnection cable for signal
output to monitor and signal
from keyboard is carrying only
SELV voltages on an energy
level below 240 VA.
→Except for the insulation
material, there are no further
requirements to the
interconnection cable.
P
1.5.6
Capacitors bridging insulation
No bridge components used.
N/A
1.5.7
Resistors bridging insulation
Ditto.
N/A
1.5.7.1
Resistors bridging functional, basic or
supplementary insulation
Ditto.
N/A
1.5.7.2
Resistors bridging double or reinforced insulation
between a.c. mains and other circuits
Ditto.
N/A
1.5.7.3
Resistors bridging double or reinforced insulation
between a.c. mains and antenna or coaxial cable
Ditto.
N/A
1.5.8
Components in equipment for IT power systems
Only SELV inside, no
connection to mains.
N/A
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 6 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
1.5.9
Surge suppressors
Only SELV circuit in this
equipment.
1.5.9.1
General
N/A
1.5.9.2
Protection of VDRs
N/A
1.5.9.3
Bridging of functional insulation by a VDR
N/A
1.5.9.4
Bridging of basic insulation by a VDR
N/A
1.5.9.5
Bridging of supplementary, double or reinforced
insulation by a VDR
N/A
1.6
Power interface
1.6.1
AC power distribution systems
Equipment is not directly
connected to the AC mains
supply.
1.6.2
Input current
The definition for highest load
according to 1.2.2.1, for this
equipment is the continuously.
Results see appended table.
P
1.6.3
Voltage limit of hand-held equipment
This equipment is not hand-held
equipment.
N/A
1.6.4
Neutral conductor
Only SELV supply, no
connection to mains.
N/A
N/A
P
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
N/A
Report reference No.: 081-100802-000
S2011.DOC
Page 7 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
1.7
Marking and instructions
1.7.1
Power rating
See below.
P
Rated voltage(s) or voltage range(s) (V) ........... :
19 Vdc
P
P
P
Symbol for nature of supply, for d.c. only ........... :
Rated frequency or rated frequency range (Hz) :
DC Source.
Rated current (mA or A) ..................................... :
2.37 A
N/A
P
Manufacturer’s name or trademark or identification MEDION
mark ................................................................... :
P
Model identification or type reference ................ :
S2011, S2012, S2013, S2213,
S2214, S2215, TT116A01,
TT116B01
Symbol for Class II equipment only ................... :
Class III equipment.
Other markings and symbols ............................. :
Additional symbols or markings
that do not give rise to
misunderstand.
P
1.7.2
Safety instructions and marking
See below.
P
1.7.2.1
General
The user’s manual contains
information for operation,
installation, servicing, transport,
storage and technical data.
The operation guide is provided
to the user.
No other special installation
instruction required as the
equipment is Class III.
P
1.7.2.2
Disconnect devices
N/A
1.7.2.3
Overcurrent protective device
N/A
1.7.2.4
IT power distribution systems
1.7.2.5
Operator access with a tool
N/A
1.7.2.6
Ozone
N/A
1.7.3
Short duty cycles
Equipment is designed for
continuous operation.
N/A
1.7.4
Supply voltage adjustment ...............................:
No voltage/frequency setting.
N/A
Only SELV inside, no
connection to mains.
Power outlets on the equipment ......................:
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
N/A
N/A
⎯
Methods and means of adjustment; reference to
installation instructions ....................................... :
1.7.5
P
No power outlet provided.
N/A
Report reference No.: 081-100802-000
S2011.DOC
Page 8 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
1.7.6
Fuse identification (marking, special fusing
characteristics, cross-reference) ....................... :
Class III equipment, such device
in approved power adapter.
N/A
1.7.7
Wiring terminals
See below.
N/A
1.7.7.1
Protective earthing and bonding terminals ........ :
Class III equipment.
N/A
1.7.7.2
Terminal for a.c. mains supply conductors
Not applied for.
N/A
1.7.7.3
Terminals for d.c. mains supply conductors
Ditto.
N/A
1.7.8
Controls and indicators
See below.
P
1.7.8.1
Identification, location and marking ................... :
The marking of stand-by switch
is located on switch so that
indication of function is clear.
P
1.7.8.2
Colours .............................................................. :
No safety involved colour
identification
1.7.8.3
Symbols according to IEC 60417 ....................... :
The stand-by switch marked
with the correct symbol (604171-IEC-5009).
1.7.8.4
Markings using figures ...................................... :
No indicators for different
positions.
N/A
1.7.9
Isolation of multiple power sources ................... :
Class III equipment not
connected to the mains.
N/A
1.7.10
Thermostats and other regulating devices ........ :
No thermostats used.
N/A
1.7.11
Durability
The label was subjected to the
permanence of marking test.
The label was rubbed with cloth
for 15 s and then again for
15 s with the cloth soaked with
Petroleum Ether.
N/A
P
P
After this test there was no
damage to the label.
The marking on the label did not
fade. There was no curling or
lifting of the label edge.
1.7.12
Removable parts
Marking is not placed on
removable part.
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
P
Report reference No.: 081-100802-000
S2011.DOC
Page 9 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
1.7.13
Replaceable batteries
The equipment contains
replaceable lithium battery pack,
user replaceable type;
The following warning in user
manual and service instructions:
(CAUTION: Danger of explosion
if battery is incorrectly replaced.
Replace only with the same or
equivalent type recommended
by the manufacturer.
Dispose of used batteries
according to the manufacturer
instructions).
P
Language ............................................................ :
English.
⎯
Equipment for restricted access locations .......... :
No restricted access location.
1.7.14
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Verdict
N/A
Report reference No.: 081-100802-000
S2011.DOC
Page 10 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
2
PROTECTION FROM HAZARDS
P
2.1
Protection from electric shock and energy hazards
P
2.1.1
Protection in operator access areas
The equipment is supplied from
an approved power adaptor that
provides only SELV voltages.
Furthermore there are no
hazardous voltages generated
internally.
Therefore there are no
protective measures required for
the protection against electrical
shock.
P
2.1.1.1
Access to energized parts
There are no energized parts
inside of equipment.
The equipment is supplied from
SELV voltage only.
P
Test by inspection .............................................. :
Ditto.
N/A
Test with test finger (Figure 2A) ............................ : Ditto.
N/A
Test with test pin (Figure 2B) ................................ : Ditto.
N/A
Test with test probe (Figure 2C) ........................... : No TNV circuits.
N/A
2.1.1.2
Battery compartments
N/A
2.1.1.3
Access to ELV wiring
No ELV wiring in operator
accessible area.
Verdict
N/A
⎯
Working voltage (Vpeak or Vrms); minimum
distance through insulation (mm)
2.1.1.4
Access to hazardous voltage circuit wiring
No hazardous voltage wiring in
operator accessible area.
N/A
2.1.1.5
Energy hazards .................................................. :
No energy hazard in operator
access area. The connectors of
the equipment below 240 VA.
P
2.1.1.6
Manual controls
No manual controls.
N/A
2.1.1.7
Discharge of capacitors in equipment
No connected to the mains.
N/A
Measured voltage (V); time-constant (s) ............... :
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
—
Report reference No.: 081-100802-000
S2011.DOC
Page 11 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
2.1.1.8
Energy hazards – d.c. mains supply
N/A
a) Capacitor connected to the d.c. mains supply . :
N/A
b) Internal battery connected to the d.c. mains
supply .................................................................... :
N/A
2.1.1.9
Audio amplifiers
N/A
2.1.2
Protection in service access areas
No maintenance work in
operation mode necessary.
N/A
2.1.3
Protection in restricted access locations
No restricted access locations.
N/A
2.2
SELV circuits
2.2.1
General requirements
42.4 V peak or 60 VDC are not
exceeded in outputs of power
supply under normal operation
or single fault condition.
P
2.2.2
Voltages under normal conditions (V) ................ :
The equipment supplied from
SELV only.
P
2.2.3
Voltages under fault conditions (V) ..................... :
The equipment supplied from
SELV only.
P
2.2.4
Connection of SELV circuits to other circuits....... :
No direct connection between
SELV and any primary circuits.
:
Verdict
P
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
N/A
Report reference No.: 081-100802-000
S2011.DOC
Page 12 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
2.3
TNV circuits
2.3.1
Limits
See below.
Type of TNV circuits ........................................... :
No TNV circuits provided.
Verdict
N/A
N/A
⎯
2.3.2
Separation from other circuits and from accessible
parts
N/A
2.3.2.1
General requirements
N/A
2.3.2.2
Protection by basic insulation
N/A
2.3.2.3
Protection by earthing
N/A
2.3.2.4
Protection by other constructions ......................... :
N/A
2.3.3
Separation from hazardous voltages
N/A
⎯
Insulation employed ............................................ :
2.3.4
Connection of TNV circuits to other circuits
N/A
Insulation employed ............................................ :
⎯
2.3.5
Test for operating voltages generated externally
N/A
2.4
Limited current circuits
N/A
2.4.1
General requirements
2.4.2
Limit values
2.4.3
TFT-LCD type with LED
backlight provided.
N/A
N/A
Frequency (Hz) ................................................... :
—
Measured current (mA) ....................................... :
—
Measured voltage (V) ......................................... :
—
Measured circuit capacitance (nF or µF) ............ :
—
Connection of limited current circuits to other
circuits
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
N/A
Report reference No.: 081-100802-000
S2011.DOC
Page 13 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
2.5
Limited power sources
Result - Remark
Verdict
P
a) Inherently limited output
The output of external power
adapter complied with the
limited power sources
inherently.
b) Impedance limited output
P
N/A
c) Regulating network limited output under normal
operating and single fault condition
The output ports are limited to
the values of table 2B.
(results see appended table)
d) Overcurrent protective device limited output
P
N/A
Max. output voltage (V), max. output current (A),
Result see appended table.
max. apparent power (VA) ..................................... :
⎯
Current rating of overcurrent protective device (A) .: No overcurrent protective
device.
⎯
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 14 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
2.6
Provisions for earthing and bonding
2.6.1
Protective earthing
2.6.2
Functional earthing
N/A
2.6.3
Protective earthing and protective bonding
conductors
N/A
2.6.3.1
General
N/A
2.6.3.2
Size of protective earthing conductors
N/A
N/A
Class III equipment, no such
concern.
Rated current (A), cross-sectional area (mm2),
AWG :
2.6.3.3
Verdict
Size of protective bonding conductors
N/A
⎯
N/A
2
Rated current (A), cross-sectional area (mm ),
AWG ...................................................................... :
⎯
Protective current rating (A), cross-sectional area
(mm2), AWG ........................................................... :
⎯
2.6.3.4
Resistance of earthing conductors and their
terminations; resistance (Ω), voltage drop (V), test
current (A), duration (min)...................................... :
N/A
2.6.3.5
Colour of insulation ................................................ :
N/A
2.6.4
Terminals
N/A
2.6.4.1
General
N/A
2.6.4.2
Protective earthing and bonding terminals
N/A
Rated current (A), type, nominal thread diameter
(mm) ....................................................................... :
⎯
2.6.4.3
Separation of the protective earthing conductor
from protective bonding conductors
N/A
2.6.5
Integrity of protective earthing
N/A
2.6.5.1
Interconnection of equipment
N/A
2.6.5.2
Components in protective earthing conductors and
protective bonding conductors
N/A
2.6.5.3
Disconnection of protective earth
N/A
2.6.5.4
Parts that can be removed by an operator
N/A
2.6.5.5
Parts removed during servicing
N/A
2.6.5.6
Corrosion resistance
N/A
2.6.5.7
Screws for protective bonding
N/A
2.6.5.8
Reliance on telecommunication network or cable
distribution system
N/A
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 15 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
2.7
Overcurrent and earth fault protection in primary circuits
N/A
2.7.1
Basic requirements
N/A
Class III equipment.
Instructions when protection relies on building
installation
Verdict
—
2.7.2
Faults not simulated in 5.3.7
N/A
2.7.3
Short-circuit backup protection
N/A
2.7.4
Number and location of protective devices ........ :
N/A
2.7.5
Protection by several devices
N/A
2.7.6
Warning to service personnel ............................. :
N/A
2.8
Safety interlocks
N/A
2.8.1
General principles
2.8.2
Protection requirements
N/A
2.8.3
Inadvertent reactivation
N/A
2.8.4
Fail-safe operation
N/A
2.8.5
Moving parts
N/A
2.8.6
Overriding
N/A
2.8.7
Switches and relays
N/A
2.8.7.1
Contact gaps (mm) ............................................ :
N/A
2.8.7.2
Overload test
N/A
2.8.7.3
Endurance test
N/A
2.8.7.4
Electric strength test
N/A
2.8.8
Mechanical actuators
N/A
No safety interlock provided.
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
N/A
Report reference No.: 081-100802-000
S2011.DOC
Page 16 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
2.9
Electrical insulation
2.9.1
Properties of insulating materials
Natural rubber, asbestos or
hygroscopic materials are used
as insulation.
2.9.2
Humidity conditioning
Class III equipment.
Verdict
P
Grade of insulation
2.9.4
Separation from hazardous voltages
The adequate levels of safety
insulation is provided and
maintained to comply with the
requirements of this standard.
Method(s) used ..................................................... :
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
N/A
⎯
Relative humidity (%), temperature (°C) ............ :
2.9.3
P
P
N/A
⎯
Report reference No.: 081-100802-000
S2011.DOC
Page 17 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
2.10
Clearances, creepage distances and distances through insulation
N/A
2.10.1
General
N/A
2.10.1.1
Frequency ............................................................. :
N/A
2.10.1.2
Pollution degrees .................................................. :
N/A
2.10.1.3
Reduced values for functional insualtion
N/A
2.10.1.4
Intervening unconnected conductive parts
N/A
2.10.1.5
Insulation with varying dimensions
N/A
2.10.1.6
Special separation requirements
N/A
2.10.1.7
Insulation in circuits generating starting pulses
N/A
2.10.2
Determination of working voltage
2.10.2.1
General
N/A
2.10.2.2
RMS working voltage
N/A
2.10.2.3
Peak working voltage
N/A
2.10.3
Clearances
2.10.3.1
General
N/A
2.10.3.2
Mains transient voltages
N/A
a) AC mains supply ............................................... :
N/A
b) Earthed d.c. mains supplies .............................. :
N/A
c) Unearthed d.c. mains supplies ......................... :
N/A
d) Battery operation .............................................. :
N/A
2.10.3.3
Clearances in primary circuits
N/A
2.10.3.4
Clearances in secondary circuits
N/A
2.10.3.5
Clearances in circuits having starting pulses
N/A
2.10.3.6
Transients from a.c. mains supply ........................ :
N/A
2.10.3.7
Transients from d.c. mains supply ........................ :
N/A
2.10.3.8
Transients from telecommunication networks and
cable distribution systems ..................................... :
N/A
Class III equipment.
See 2.10.3 and 2.10.4.
It has been evaluated in
approved external power
adapter.
Provided by the approved
external power adapter.
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Verdict
N/A
N/A
Report reference No.: 081-100802-000
S2011.DOC
Page 18 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
2.10.3.9
Measurement of transient voltage levels
N/A
a) Transients from a mains suplply
N/A
For an a.c. mains supply ....................................... :
N/A
For a d.c. mains supply ......................................... :
N/A
b) Transients from a telecommunication network :
N/A
2.10.4
Creepage distances
2.10.4.1
General
N/A
2.10.4.2
Material group and caomparative tracking index
N/A
Provided by the approved
external power adapter
CTI tests ................................................................. :
N/A
⎯
2.10.4.3
Minimum creepage distances
N/A
2.10.5
Solid insulation
N/A
2.10.5.1
General
N/A
2.10.5.2
Distances through insulation
2.10.5.3
Insulating compound as solid insulation
N/A
2.10.5.4
Semiconductor devices
N/A
2.10.5.5.
Cemented joints
N/A
2.10.5.6
Thin sheet material – General
N/A
2.10.5.7
Separable thin sheet material
N/A
⎯
Number of layers (pcs) .......................................... :
⎯
2.10.5.8
Non-separable thin sheet material
N/A
2.10.5.9
Thin sheet material – standard test procedure
N/A
⎯
Electric strength test
2.10.5.10
Thin sheet material – alternative test procedure
N/A
⎯
Electric strength test
2.10.5.11
Insulation in wound components
N/A
2.10.5.12
Wire in wound components
N/A
Working voltage .................................................... :
N/A
a) Basic insulation not under stress ...................... :
N/A
b) Basic, supplemetary, reinforced insulation ....... :
N/A
c) Compliance with Annex U ................................. :
N/A
Two wires in contact inside wound component;
angle between 45° and 90° .................................. :
⎯
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 19 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
2.10.5.13
Wire with solvent-based enamel in wound
components
Verdict
N/A
⎯
Electric strength test
Routine test
N/A
Additional insulation in wound components
N/A
Working voltage ................................................ :
N/A
- Basic insulation not under stress .................... :
N/A
- Supplemetary, reinforced insulation ............... :
N/A
2.10.6
Construction of printed boards
N/A
2.10.6.1
Uncoated printed boards
N/A
2.10.6.2
Coated printed boards
2.10.6.3
Insulation between conductors on the same inner
surface of a printed board
N/A
2.10.6.4
Insulation between conductors on different layers
of a printed board
N/A
Distance through insulation
N/A
Number of insulation layers (pcs) ...................... :
N/A
2.10.7
Component external terminations
N/A
2.10.8
Tests on coated printed boards and coated
components
N/A
2.10.8.1
Sample preparation and preliminary inspection
N/A
2.10.8.2
Thermal conditioning
N/A
2.10.8.3
Electric strength test
⎯
2.10.8.4
Abrasion resistance test
N/A
2.10.9
Thermal cycling
N/A
2.10.10
Test for Pollution Degree 1 environment and
insulating compound
N/A
2.10.11
Tests for semiconductor devices and cemented
joints
N/A
2.10.12
Enclosed and sealed parts
2.10.5.14
No coated printed board.
No hermetically sealed
components.
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
N/A
N/A
Report reference No.: 081-100802-000
S2011.DOC
Page 20 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
3
WIRING, CONNECTIONS AND SUPPLY
P
3.1
General
P
3.1.1
Current rating and overcurrent protection
All internal wires are UL
recognized wiring that is PVC
insulated, rated VW-1, min.
60°C, 300V.
P
3.1.2
Protection against mechanical damage
Wires do not touch sharp edges
which could damage the
insulation and cause hazard.
P
3.1.3
Securing of internal wiring
The wires are secured by
solder so that a loosening of
the terminal connection is
unlikely.
P
3.1.4
Insulation of conductors
The insulation of the individual
conductors is suitable for the
application and the working
voltage.
For the insulation material see
3.1.1.
P
3.1.5
Beads and ceramic insulators
Not used.
3.1.6
Screws for electrical contact pressure
Electrical connections screwed
two or more complete threads
into metal.
No screws of insulating material
for electrical connection, or
where supplementary or
reinforced insulation could be
impaired by a metal
replacement.
P
3.1.7
Insulating materials in electrical connections
All current carrying connection
is metal to metal.
P
3.1.8
Self-tapping and spaced thread screws
No self tapping screws are
used.
3.1.9
Termination of conductors
N/A
N/A
N/A
⎯
10 N pull test
3.1.10
Verdict
Sleeving on wiring
Sleevings on wiring reliable
kept in position by cable ties or
by the use of heatshrunk
sleeving.
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
P
Report reference No.: 081-100802-000
S2011.DOC
Page 21 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
3.2
Connection to a mains supply
3.2.1
Means of connection
3.2.1.1
Connection to an a.c. mains supply
N/A
3.2.1.2
Connection to a d.c. mains supply
N/A
3.2.2
Multiple supply connections
N/A
3.2.3
Permanently connected equipment
N/A
N/A
Class III equipment, no
connection to mains directly.
N/A
⎯
Number of conductors, diameter of cable and
conduits (mm) .................................................... :
3.2.4
Appliance inlets
N/A
3.2.5
Power supply cords
N/A
3.2.5.1
AC power supply cords
N/A
⎯
Type .................................................................... :
2
Rated current (A), cross-sectional area (mm ),
AWG ................................................................... :
⎯
3.2.5.2
DC power supply cords
N/A
3.2.6
Cord anchorages and strain relief
N/A
Mass of equipment (kg), pull (N) ...................... :
⎯
Longitudinal displacement (mm) ........................ :
⎯
3.2.7
Protection against mechanical damage
N/A
3.2.8
Cord guards
N/A
3.2.9
Diameter or minor dimension D (mm); test mass (g)
............................................................................... :
⎯
Radius of curvature of cord (mm) .......................... :
⎯
Supply wiring space
N/A
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 22 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
3.3
Wiring terminals for connection of external conductors
N/A
3.3.1
Wiring terminals
N/A
3.3.2
Connection of non-detachable power supply cords
N/A
3.3.3
Screw terminals
N/A
3.3.4
Conductor sizes to be connected
N/A
⎯
Rated current (A), cord/cable type, cross-sectional
area (mm2) .......................................................... :
3.3.5
Verdict
Wiring terminal sizes
N/A
⎯
Rated current (A), type and nominal thread
diameter (mm) .................................................... :
3.3.6
Wiring terminals design
N/A
3.3.7
Grouping of wiring terminals
N/A
3.3.8
Stranded wire
N/A
3.4
Disconnection from the mains supply
N/A
3.4.1
General requirement
3.4.2
Disconnect devices
N/A
3.4.3
Permanently connected equipment
N/A
3.4.4
Parts which remain energized
N/A
3.4.5
Switches in flexible cords
N/A
3.4.6
Number of poles - single-phase and d.c.
equipment
N/A
3.4.7
Number of poles - three-phase equipment
N/A
3.4.8
Switches as disconnect devices
N/A
3.4.9
Plugs as disconnect devices
N/A
3.4.10
Interconnected equipment
N/A
3.4.11
Multiple power sources
N/A
Class III equipment, no
connection to mains directly.
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
N/A
Report reference No.: 081-100802-000
S2011.DOC
Page 23 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
3.5
Interconnection of equipment
3.5.1
General requirements
See below.
P
3.5.2
Types of interconnection circuits ......................... :
Interconnection circuits of SELV
through the connectors.
No ELV interconnection circuits.
P
3.5.3
ELV circuits as interconnection circuits
No ELV interconnection.
3.5.4
Data ports for additional equipment
The output of data ports are
comply with limited power
source, refer also appended
table 2.5.
P
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
N/A
P
Report reference No.: 081-100802-000
S2011.DOC
Page 24 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
4
PHYSICAL REQUIREMENTS
P
4.1
Stability
P
Angle of 10°
This equipment is less than 7
kg.
Test: force (N) ...................................................... :
Equipment is not a floor
standing unit.
Verdict
P
N/A
4.2
Mechanical strength
P
4.2.1
General
4.2.2
Steady force test, 10 N
N/A
4.2.3
Steady force test, 30 N
N/A
4.2.4
Steady force test, 250 N
250 N applied to outer
enclosure.
No energy or other hazards.
4.2.5
Impact test
Not apply for.
After the tests, the equipment is
still complying with relevant
requirements of this standard.
See below.
P
P
N/A
Fall test
N/A
Swing test
N/A
4.2.6
Drop test; height (mm)………………………………:
The equipment is subjected to
three impacts that result from
being dropped onto a horizontal
surface.
The height of drop:
1,000 mm ± 10 mm.
P
4.2.7
Stress relief test
After 7h at 70°C and cooling
down to room temperature, no
shrinkage, distortion or loosing
of enclosure parts.
P
4.2.8
Cathode ray tubes
No cathode ray tube.
Picture tube separately certified ......................... :
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
N/A
⎯
Report reference No.: 081-100802-000
S2011.DOC
Page 25 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
4.2.9
High pressure lamps
No high pressure lamp provided.
N/A
4.2.10
Wall or ceiling mounted equipment; force (N) ... :
Not wall or ceiling mounted
equipment.
N/A
4.3
Design and construction
4.3.1
Edges and corners
4.3.2
Handles and manual controls; force (N) ............. :
4.3.3
Adjustable controls
None that would cause hazard.
N/A
4.3.4
Securing of parts
No connections likely to be
exposed to mechanical stress
are provided in unit.
P
4.3.5
Connection of plugs and sockets
Only SELV connector.
N/A
4.3.6
Direct plug-in equipment
The equipment is not a direct
plug-in unit.
N/A
P
Edges and corners of the
enclosure are rounded.
P
N/A
Torque ................................................................ :
⎯
Compliance with the relevant mains plug standard
............................................................................ :
⎯
4.3.7
Heating elements in earthed equipment
No heating elements.
4.3.8
Batteries
Battery pack is approval
component, perform test for
RTC battery.
(see appended table 5.3).
P
- Overcharging of a rechargeable battery
See appended table 5.3 for
details.
P
- Unintentional charging of a non-rechargeable
battery
Not apply for.
- Reverse charging of a rechargeable battery
See appended table 5.3 for
details.
P
- Excessive discharging rate for any battery
See appended table 5.3 for
details.
P
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
N/A
N/A
Report reference No.: 081-100802-000
S2011.DOC
Page 26 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
4.3.9
Oil and grease
Insulation not in contact with oil
or grease.
N/A
4.3.10
Dust, powders, liquids and gases
Equipment in intended use not
considered to be exposed to
these.
N/A
4.3.11
Containers for liquids or gases
The equipment does not contain
liquid.
N/A
4.3.12
Flammable liquids ............................................... :
No flammable liquids in this unit.
N/A
Quantity of liquid (l) ............................................. :
⎯
Flash point (°C) ................................................... :
⎯
4.3.13
Radiation; type of radiation ................................ :
4.3.13.1
General
N/A
4.3.13.2
Ionizing radiation
N/A
4.3.13.3
No radiation.
N/A
Measured radiation (pA/kg) ................................ :
⎯
Measured high-voltage (kV) ................................ :
⎯
Measured focus voltage (kV) .............................. :
⎯
CRT markings ..................................................... :
⎯
Effect of ultraviolet (UV) radiation on materials
No UV radiation.
N/A
Part, property, retention after test, flammability
classification ........................................................ :
⎯
4.3.13.4
Human exposure to ultraviolet (UV) radiation .... :
N/A
4.3.13.5
Laser (including LEDs)
N/A
Laser class ......................................................... :
⎯
4.3.13.6
Other types ........................................................ :
N/A
4.4
Protection against hazardous moving parts
4.4.1
General
See below.
P
4.4.2
Protection in operator access areas
No hazardous moving part in
access area.
The DC fan was not accessible.
P
4.4.3
Protection in restricted access locations
The equipment is not intended
to be used in restricted
locations.
4.4.4
Protection in service access areas
Unintentional contact is not
possible.
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
P
N/A
P
Report reference No.: 081-100802-000
S2011.DOC
Page 27 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
4.5
Thermal requirements
4.5.1
General
See below.
P
4.5.2
Temperature tests
(see appended table 4.5)
P
Normal load condition per Annex L ..................... :
Maximum normal load which
specified by manufacturer.
⎯
4.5.3
Temperature limits for materials
(see appended table 4.5)
P
4.5.4
Touch temperature limits
(see appended table 4.5)
P
4.5.5
Resistance to abnormal heat ............................... :
Only SELV circuit.
4.6
Openings in enclosures
4.6.1
Top and side openings
P
N/A
P
Refer to 4.6.4.
Bottoms of fire enclosures
P
⎯
Dimensions (mm) ............................................... :
4.6.2
Verdict
Refer to 4.6.4.
P
⎯
Construction of the bottom.................................. :
4.6.3
Doors or covers in fire enclosures
No door or cover.
4.6.4
Openings in transportable equipment
See appended table.
4.6.4.1
Constructional design measures
N/A
P
N/A
Dimensions (mm) ................................................. :
⎯
4.6.4.2
Evaluation measures for larger openings
N/A
4.6.4.3
Use of metallized parts
N/A
4.6.5
Adhesives for constructional purposes
N/A
Conditioning temperature (°C)/time (weeks) ...... :
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
⎯
Report reference No.: 081-100802-000
S2011.DOC
Page 28 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
4.7
Resistance to fire
4.7.1
Reducing the risk of ignition and spread of flame
Verdict
P
Use of materials with the
required flammability classes.
Method 1, selection and application of components Selection and application of
wiring and materials
components and materials
which minimize the possibility
of ignition and spread of flame.
Method 2, application of all of simulated fault
condition tests
P
P
N/A
4.7.2
Conditions for a fire enclosure
See below.
P
4.7.2.1
Parts requiring a fire enclosure
With having the following
components:
- components with windings
- semiconductor devices,
transistors, diodes,
integrated circuits
- resistors, capacitors,
inductors
P
the fire enclosure is required.
4.7.2.2
Parts not requiring a fire enclosure
See 4.7.2.1.
N/A
4.7.3
Materials
4.7.3.1
General
Integrated circuits and small
electrical parts mounted on a
printed wiring board min. rated
V-1.
P
4.7.3.2
Materials for fire enclosures
See appended table 1.5.1.
P
4.7.3.3
Materials for components and other parts outside
fire enclosures
No components or parts outside
fire enclosures.
4.7.3.4
Materials for components and other parts inside
fire enclosures
Internal components except
small parts are V-2, HF-2 or
better.
4.7.3.5
Materials for air filter assemblies
No air filters assemblies.
N/A
4.7.3.6
Materials used in high-voltage components
No high voltage component
used.
N/A
P
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
N/A
P
Report reference No.: 081-100802-000
S2011.DOC
Page 29 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
5
ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS
5.1
Touch current and protective conductor current
5.1.1
General
5.1.2
Configuration of equipment under test (EUT)
N/A
5.1.2.1
Single connection to an a.c. mains supply
N/A
5.1.2.2
Redundant multiple connections to an a.c. mains
supply
N/A
5.1.2.3
Simultaneous multiple connections to an a.c.
mains supply
N/A
5.1.3
Test circuit
N/A
5.1.4
Application of measuring instrument
N/A
5.1.5
Test procedure
N/A
5.1.6
Test measurements
N/A
P
N/A
Class III equipment with
approved external power
adapter.
N/A
Supply voltage (V) ................................................ :
⎯
Measured touch current (mA) .............................. :
⎯
Max. allowed touch current (mA) ......................... :
⎯
Measured protective conductor current (mA) ...... :
⎯
Max. allowed protective conductor current (mA) .. :
⎯
5.1.7
Equipment with touch current exceeding 3,5 mA
N/A
5.1.7.1
General ................................................................ :
N/A
5.1.7.2
Simultaneous multiple connections to the supply
N/A
5.1.8
Touch currents to telecommunication networks
and cable distribution systems and from
telecommunication networks
N/A
5.1.8.1
Limitation of the touch current to a
telecommunication network or to a cable
distribution system
N/A
Supply voltage (V) ................................................ :
⎯
Measured touch current (mA) .............................. :
⎯
Max. allowed touch current (mA) ......................... :
⎯
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 30 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
5.1.8.2
Summation of touch currents from
telecommunication networks
N/A
a) EUT with earthed telecommunication ports .... :
N/A
b) EUT whose telecommunication ports have no
reference to protective earth
N/A
5.2
Electric strength
N/A
5.2.1
General
5.2.2
Test procedure
5.3
Abnormal operating and fault conditions
5.3.1
Protection against overload and abnormal
operation
Blocked openings and stalled
fan test, results see appended
table.
P
5.3.2
Motors
Approved DC fan used.
See appended table 5.3
P
5.3.3
Transformers
The safety isolation transformer
is inside the approved external
power adapter.
5.3.4
Functional insulation ............................................. :
5.3.5
Electromechanical components
5.3.6
Audio amplifiers in ITE ......................................... :
5.3.7
Simulation of faults
Result see appended table.
5.3.8
Unattended equipment
None of them are used.
5.3.9
Compliance criteria for abnormal operating and
fault conditions
No fire propagated beyond the
equipment. No molten metal
was emitted.
P
5.3.9.1
During the tests
Ditto.
P
5.3.9.2
After the tests
Ditto.
P
Class III equipment.
Verdict
N/A
N/A
P
N/A
No electromechanical
components.
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
N/A
N/A
N/A
P
N/A
Report reference No.: 081-100802-000
S2011.DOC
Page 31 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
6
CONNECTION TO TELECOMMUNICATION NETWORKS
N/A
6.1
Protection of telecommunication network service persons, and users of other
equipment connected to the network, from hazards in the equipment
N/A
6.1.1
Protection from hazardous voltages
N/A
6.1.2
Separation of the telecommunication network from earth
N/A
6.1.2.1
Requirements
N/A
Not direct connection to
TELECOMMUNICATION
NETWORK.
Verdict
Supply voltage (V) .............................................. :
⎯
Current in the test circuit (mA) ......................... :
⎯
6.1.2.2
Exclusions ........................................................... :
N/A
6.2
Protection of equipment users from overvoltages on telecommunication networks
N/A
6.2.1
Separation requirements
N/A
6.2.2
Electric strength test procedure
N/A
6.2.2.1
Impulse test
N/A
6.2.2.2
Steady-state test
N/A
6.2.2.3
Compliance criteria
N/A
6.3
Protection of the telecommunication wiring system from overheating
N/A
Max. output current (A) ....................................... :
⎯
Current limiting method....................................... :
⎯
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 32 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
7
CONNECTION TO CABLE DISTRIBUTION SYSTEMS
N/A
7.1
General
N/A
7.2
Protection of cable distribution system service
persons, and users of other equipment connected
to the system, from hazardous voltages in the
equipment
N/A
7.3
Protection of equipment users from overvoltages
on the cable distribution system
N/A
7.4
Insulation between primary circuits and cable
distribution systems
N/A
7.4.1
General
N/A
7.4.2
Voltage surge test
N/A
7.4.3
Impulse test
N/A
No connection to CABLE
DISTRIBUTION SYSTEMS.
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Verdict
Report reference No.: 081-100802-000
S2011.DOC
Page 33 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
A
ANNEX A, TESTS FOR RESISTANCE TO HEAT AND FIRE
N/A
A.1
Flammability test for fire enclosures of movable
equipment having a total mass exceeding 18 kg,
and of stationary equipment (see 4.7.3.2)
N/A
A.1.1
Samples ................................................................ :
⎯
Wall thickness (mm) ............................................. :
⎯
A.1.2
Conditioning of samples; temperature (°C) ......... :
N/A
A.1.3
Mounting of samples ............................................ :
N/A
A.1.4
Test flame (see IEC 60695-11-3)
N/A
⎯
Flame A, B, C or D ............................................... :
A.1.5
Test procedure
N/A
A.1.6
Compliance criteria
N/A
Sample 1 burning time (s)..................................... :
⎯
Sample 2 burning time (s)..................................... :
⎯
Sample 3 burning time (s)..................................... :
⎯
A.2
Flammability test for fire enclosures of movable equipment having a total mass not
exceeding 18 kg, and for material and components located inside fire enclosures
(see 4.7.3.2 and 4.7.3.4)
A.2.1
Samples, material ................................................. :
⎯
Wall thickness (mm) ............................................. :
⎯
A.2.2
Conditioning of samples; temperature (°C) ......... :
N/A
A.2.3
Mounting of samples ............................................ :
N/A
A.2.4
Test flame (see IEC 60695-11-4)
N/A
Flame A, B or C ................................................... :
N/A
⎯
A.2.5
Test procedure
N/A
A.2.6
Compliance criteria
N/A
A.2.7
Sample 1 burning time (s)..................................... :
⎯
Sample 2 burning time (s)..................................... :
⎯
Sample 3 burning time (s)..................................... :
⎯
Alternative test acc. to IEC 60695-11-5, cl. 5 and 9
N/A
Sample 1 burning time (s)..................................... :
⎯
Sample 2 burning time (s)..................................... :
⎯
Sample 3 burning time (s)..................................... :
⎯
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 34 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
A.3
Hot flaming oil test (see 4.6.2)
N/A
A.3.1
Mounting of samples
N/A
A.3.2
Test procedure
N/A
A.3.3
Compliance criterion
N/A
B
Annex B, MOTOR TESTS UNDER ABNORMAL CONDITIONS (see 4.7.2.2 and
5.3.2)
N/A
B.1
General requirements
N/A
Position ............................................................... :
⎯
Manufacturer ...................................................... :
⎯
Type .................................................................... :
⎯
Rated values ...................................................... :
⎯
B.2
Test conditions
N/A
B.3
Maximum temperatures
N/A
B.4
Running overload test
N/A
B.5
Locked-rotor overload test
N/A
Test duration (days) ............................................ :
⎯
Electric strength test: test voltage (V) ................. :
⎯
B.6
Running overload test for d.c. motors in
secondary circuits
N/A
B.6.1
General
N/A
B.6.2
Test procedure
N/A
B.6.3
Alternative test procedure
N/A
B.6.4
Electric strength test; test voltage (V) ...................:
N/A
B.7
Locked-rotor overload test for d.c. motors in
secondary circuits
N/A
B.7.1
General
N/A
B.7.2
Test procedure
N/A
B.7.3
Alternative test procedure
N/A
B.7.4
Electric strength test; test voltage (V) .................. :
N/A
B.8
Test for motors with capacitors
N/A
B.9
Test for three-phase motors
N/A
B.10
Test for series motors
N/A
Operating voltage (V) .......................................... :
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
⎯
Report reference No.: 081-100802-000
S2011.DOC
Page 35 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
C
Requirement + Test
Result - Remark
Annex C, TRANSFORMERS (see 1.5.4 and 5.3.3)
Verdict
N/A
Position ...............................................................:
⎯
Manufacturer ......................................................:
⎯
Type ....................................................................:
⎯
Rated values ......................................................:
⎯
Method of protection ........................................... :
⎯
C.1
Overload test
N/A
C.2
Insulation
N/A
Protection from displacement of windings .......... :
N/A
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 36 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
D
ANNEX D, MEASURING INSTRUMENTS FOR TOUCH-CURRENT TESTS
(see 5.1.4)
N/A
D.1
Measuring instrument
N/A
D.2
Alternative measuring instrument
N/A
E
ANNEX E, TEMPERATURE RISE OF A WINDING (see 1.4.13)
N/A
F
ANNEX F, MEASUREMENT OF CLEARANCES AND CREEPAGE DISTANCES
(see 2.10 and Annex G)
G
ANNEX G, ALTERNATIVE METHOD FOR DETERMINING MINIMUM
CLEARANCES
N/A
G.1
Clearances
N/A
G.1.1
General
N/A
G.1.2
Summary of the procedure for determining
minimum clearances
N/A
G.2
Determination of mains transient voltage (V)
N/A
G.2.1
AC mains supply .................................................. :
N/A
G.2.2
Earthed d.c. mains supplies ................................. :
N/A
G.2.3
Unearthed d.c. mains supplies ............................ :
N/A
G.2.4
Battery operation .................................................. :
N/A
G.3
Determination of telecommunication network
transient voltage (V) ............................................. :
N/A
G.4
Determination of required withstand voltage (V)
N/A
G.4.1
Mains transients and internal repetitive peaks .... :
N/A
G.4.2
Transients from telecommunication networks ..... :
N/A
G.4.3
Combination of transients
N/A
G.4.4
Transients from cable distribution systems
N/A
G.5
Measurement of transient voltages (V)
N/A
a) Transients from a mains supply
N/A
For an a.c. mains supply
N/A
For a d.c. mains supply
N/A
b) Transients from a telecommunication network
N/A
Determination of minimum clearances ................ :
N/A
G.6
Result - Remark
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Verdict
P
Report reference No.: 081-100802-000
S2011.DOC
Page 37 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
H
ANNEX H, IONIZING RADIATION (see 4.3.13)
N/A
J
ANNEX J, TABLE OF ELECTROCHEMICAL POTENTIALS (see 2.6.5.6)
N/A
⎯
Metal(s) used ....................................................... :
K
ANNEX K, THERMAL CONTROLS (see 1.5.3 and 5.3.8)
N/A
K.1
Making and breaking capacity
N/A
K.2
Thermostat reliability; operating voltage (V) ........ :
N/A
K.3
Thermostat endurance test; operating voltage (V)
.............................................................................. :
N/A
K.4
Temperature limiter endurance; operating voltage
(V) ........................................................................ :
N/A
K.5
Thermal cut-out reliability
N/A
K.6
Stability of operation
N/A
L
ANNEX L, NORMAL LOAD CONDITIONS FOR SOME TYPES OF ELECTRICAL
BUSINESS EQUIPMENT (see 1.2.2.1 and 4.5.2)
L.1
Typewriters
N/A
L.2
Adding machines and cash registers
N/A
L.3
Erasers
N/A
L.4
Pencil sharpeners
N/A
L.5
Duplicators and copy machines
N/A
L.6
Motor-operated files
N/A
L.7
Other business equipment
P
P
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 38 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
M
ANNEX M, CRITERIA FOR TELEPHONE RINGING SIGNALS (see 2.3.1)
N/A
M.1
Introduction
N/A
M.2
Method A
N/A
M.3
Method B
N/A
M.3.1
Ringing signal
N/A
M.3.1.1
Frequency (Hz) .................................................... :
⎯
M.3.1.2
Voltage (V) ........................................................... :
⎯
M.3.1.3
Cadence; time (s), voltage (V) ............................. :
⎯
M.3.1.4
Single fault current (mA) ...................................... :
⎯
M.3.2
Tripping device and monitoring voltage ............... :
N/A
M.3.2.1
Conditions for use of a tripping device or a
monitoring voltage
N/A
M.3.2.2
Tripping device
N/A
M.3.2.3
Monitoring voltage (V) .......................................... :
N/A
N
ANNEX N, IMPULSE TEST GENERATORS (see 1.5.7.2, 1.5.7.3, 2.10.3.9, 6.2.2.1,
7.3.2, 7.4.3 and Clause G.5)
N/A
N.1
ITU-T impulse test generators
N/A
N.2
IEC 60065 impulse test generator
N/A
P
ANNEX P, NORMATIVE REFERENCES
Q
ANNEX Q, Voltage dependent resistors (VDRs) (see 1.5.9.1)
N/A
a) Preferred climatic categories ........................... :
N/A
b) Maximum continuous voltage .......................... :
N/A
c) Pulse current .................................................... :
N/A
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Verdict
⎯
Report reference No.: 081-100802-000
S2011.DOC
Page 39 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
R
ANNEX R, EXAMPLES OF REQUIREMENTS FOR QUALITY CONTROL
PROGRAMMES
N/A
R.1
Minimum separation distances for unpopulated
coated printed boards (see 2.10.6.2)
N/A
R.2
Reduced clearances (see 2.10.3)
N/A
S
ANNEX S, PROCEDURE FOR IMPULSE TESTING (see 6.2.2.3)
N/A
S.1
Test equipment
N/A
S.2
Test procedure
N/A
S.3
Examples of waveforms during impulse testing
N/A
T
ANNEX T, GUIDANCE ON PROTECTION AGAINST INGRESS OF WATER
(see 1.1.2)
N/A
⎯
U
ANNEX U, INSULATED WINDING WIRES FOR USE WITHOUT INTERLEAVED
INSULATION (see 2.10.5.4)
N/A
⎯
V
ANNEX V, AC POWER DISTRIBUTION SYSTEMS (see 1.6.1)
N/A
V.1
Introduction
N/A
V.2
TN power distribution systems
N/A
V.3
TT power systems
N/A
V.4
IT power systems
N/A
Class III equipment.
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 40 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
W
ANNEX W, SUMMATION OF TOUCH CURRENTS
N/A
W.1
Touch current from electronic circuits
N/A
W.1.1
Floating circuits
N/A
W.1.2
Earthed circuits
N/A
W.2
Interconnection of several equipments
N/A
W.2.1
Isolation
N/A
W.2.2
Common return, isolated from earth
N/A
W.2.3
Common return, connected to protective earth
N/A
X
ANNEX X, MAXIMUM HEATING EFFECT IN TRANSFORMER TESTS (see clause
C.1)
N/A
X.1
Determination of maximum input current
N/A
X.2
Overload test procedure
N/A
Y
ANNEX Y, ULTRAVIOLET LIGHT CONDITIONING TEST (see 4.3.13.3)
N/A
Y.1
Test apparatus ..................................................... :
N/A
Y.2
Mounting of test samples ..................................... :
N/A
Y.3
Carbon-arc light-exposure apparatus .................. :
N/A
Y.4
Xenon-arc light exposure apparatus .................... :
N/A
Z
ANNEX Z, OVERVOLTAGE CATEGORIES (see 2.10.3.2 and Clause G.2)
N/A
AA
ANNEX AA, MANDREL TEST (see 2.10.5.8)
N/A
BB
ANNEX BB, CHANGES IN THE SECOND EDITION
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Verdict
⎯
Report reference No.: 081-100802-000
S2011.DOC
Page 41 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
EN 60950-1:2006 – CENELEC COMMON MODIFICATIONS
Contents
Add the following annexes:
P
Annex ZA (normative)
Normative references to international publications
with their corresponding European publications
Annex ZB (normative)
Annex ZC (informative)
General
A-deviations
Delete all the “country” notes in the reference document according to the following
list:
1.4.8
1.5.8
2.2.3
2.3.2.1
2.7.1
3.2.1.1
4.3.6
4.7.3.1
6
6.2.2
7.1
G.2.1
1.3.Z1
Special national conditions
Note 2
Note 2
Note
Note 2
Note
Note
Note 1 & 2
Note 2
Note 2 & 5
Note 6.
Note 3
Note 2
1.5.1
1.5.9.4
2.2.4
2.3.4
2.10.3.2
3.2.4
4.7
5.1.7.1
6.1.2.1
2.2.1
7.2
Annex H
Note 2 & 3
Note
Note
Note 2
Note 2
Note 3.
Note 4
Note 3 & 4
Note 2
Note 2
Note
Note 2
1.5.7.1
1.7.2.1
2.3.2
2.6.3.3
2.10.5.13
2.5.1
4.7.2.2
5.3.7
6.1.2.2
6.2.2.2
7.3
P
Note
Note 4, 5 & 6
Note
Note 2 & 3
Note 3
Note 2
Note
Note 1
Note
Note
Note 1 & 2
P
Add the following subclause:
1.3.Z1 Exposure to excessive sound pressure
The apparatus shall be so designed and constructed as to present no danger when
used for its intended purpose, either in normal operating conditions or under fault
conditions, particularly providing protection against exposure to excessive sound
pressures from headphones or earphones.
NOTE Z1 A new method of measurement is described in EN 50332-1, Sound
system equipment:
Headphones and earphones associated with portable audio equipment - Maximum
sound pressure level measurement methodology and limit considerations - Part 1:
General method for “one package equipment”, and in EN 50332-2, Sound system
equipment: Headphones and earphones associated with portable audio equipment Maximum sound pressure level measurement methodology and limit considerations
- Part 2: Guidelines to associate sets with headphones coming from different
manufacturers.
1.5.1
Add the following NOTE:
N/A
NOTE Z1 The use of certain substances in electrical and electronic equipment is
restricted within the EU: see Directive 2002/95/EC
1.7.2.1
Add the following NOTE:
N/A
NOTE Z1 In addition, the instructions shall include, as far as applicable, a warning
that excessive sound pressure from earphones and headphones can cause hearing
loss
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 42 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
2.7.1
Replace the subclause as follows:
Verdict
P
Basic requirements
To protect against excessive current, short-circuits and earth faults in PRIMARY
CIRCUITS, protective devices shall be included either as integral parts of the
equipment or as parts of the building installation, subject to the following, a), b) and
c):
a) except as detailed in b) and c), protective devices necessary to comply with the
requirements of 5.3 shall be included as parts of the equipment;
b) for components in series with the mains input to the equipment such as the supply
cord, appliance coupler, r.f.i. filter and switch, short-circuit and earth fault protection
may be provided by protective devices in the building installation;
c) it is permitted for PLUGGABLE EQUIPMENT TYPE B or PERMANENTLY
CONNECTED EQUIPMENT, to rely on dedicated overcurrent and short-circuit
protection in the building installation, provided that the means of protection, e.g.
fuses or circuit breakers, is fully specified in the installation instructions.
If reliance is placed on protection in the building installation, the installation
instructions shall so state, except that for PLUGGABLE EQUIPMENT TYPE A the
building installation shall be regarded as providing protection in accordance with the
rating of the wall socket outlet.
2.7.2
This subclause has been declared ‘void’.
N/A
3.2.3
Delete the NOTE in Table 3A, and delete also in this table the conduit sizes in
parentheses.
N/A
3.2.5.1
Replace
N/A
“60245 IEC 53” by “H05 RR-F”;
“60227 IEC 52” by “H03 VV-F or H03 VVH2-F”;
“60227 IEC 53” by “H05 VV-F or H05 VVH2-F2”.
In Table 3B, replace the first four lines by the following:
| Up to and including 6
|
| Over 6 up to and including 10 |
| Over 10 up to and including 16 |
(0,75)
(1,0) c)
0,75 a)
1,0
1,5
b)
|
|
|
In the conditions applicable to Table 3B delete the words “in some countries” in
condition a).
In NOTE 1, applicable to Table 3B, delete the second sentence.
3.3.4
In Table 3D, delete the fourth line: conductor sizes for 10 to 13 A, and replace with
the following:
| Over 10 up to and including 16 |
1,5 to 2,5
|
1,5 to 4
N/A
|
Delete the fifth line: conductor sizes for 13 to 16 A.
4.3.13.6
Add the following NOTE:
N/A
NOTE Z1 Attention is drawn to 1999/519/EC: Council Recommendation on the
limitation of exposure of the general public to electromagnetic fields 0 Hz to 300
GHz. Standards taking into account this Recommendation which demonstrate
compliance with the applicable EU Directive are indicated in the OJEC.
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 43 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Annex H
Replace the last paragraph of this annex by:
Verdict
N/A
At any point 10 cm from the surface of the OPERATOR ACCESS AREA, the dose
rate shall not exceed 1 μSv/h (0,1 mR/h) (see NOTE). Account is taken of the
background level.
Replace the notes as follows:
NOTE These values appear in Directive 96/29/Euratom.
Delete NOTE 2.
Bibliography
Additional EN standards.
⎯
ZA
NORMATIVE REFERENCES TO INTERNATIONAL PUBLICATIONS WITH THEIR
CORRESPONDING EUROPEAN PUBLICATIONS
⎯
ZB
SPECIAL NATIONAL CONDITIONS
N/A
1.2.4.1
In Denmark, certain types of Class I appliances (see 3.2.1.1) may be provided with
a plug not establishing earthing conditions when inserted into Danish socket-outlets.
N/A
1.5.7.1
In Finland, Norway and Sweden, resistors bridging BASIC INSULATION in CLASS
I PLUGGABLE EQUIPMENT TYPE A must comply with the requirements in 1.5.7.2.
N/A
1.5.8
In Norway, due to the IT power system used (see annex V, Figure V.7), capacitors
are required to be rated for the applicable line-to-line voltage (230 V).
N/A
1.5.9.4
In Finland, Norway and Sweden, the third dashed sentence is applicable only to
equipment as defined in 6.1.2.2 of this annex.
N/A
1.7.2.1
In Finland, Norway and Sweden, CLASS I PLUGGABLE EQUIPMENT TYPE A
intended for connection to other equipment or a network shall, if safety relies on
connection to protective earth or if surge suppressors are connected between the
network terminals and accessible parts, have a marking stating that the equipment
must be connected to an earthed mains socket-outlet.
N/A
The marking text in the applicable countries shall be as follows:
In Finland: "Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan"
In Norway: “Apparatet må tilkoples jordet stikkontakt”
In Sweden: “Apparaten skall anslutas till jordat uttag”
1.7.5
In Denmark, socket-outlets for providing power to other equipment shall be in
accordance with the Heavy Current Regulations, Section 107-2-D1, Standard Sheet
DK 1-3a, DK 1-5a or DK 1-7a, when used on Class I equipment. For STATIONARY
EQUIPMENT the socket-outlet shall be in accordance with Standard Sheet DK 1-1b
or DK 1-5a.
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
N/A
Report reference No.: 081-100802-000
S2011.DOC
Page 44 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
2.2.4
In Norway, for requirements see 1.7.2.1, 6.1.2.1 and 6.1.2.2 of this annex.
N/A
2.3.2
In Finland, Norway and Sweden there are additional requirements for the
insulation. See 6.1.2.1 and 6.1.2.2 of this annex.
N/A
2.3.4
In Norway, for requirements see 1.7.2.1, 6.1.2.1 and 6.1.2.2 of this annex.
N/A
2.6.3.3
In the United Kingdom, the current rating of the circuit shall be taken as 13 A, not
16 A.
N/A
2.7.1
In the United Kingdom, to protect against excessive currents and short-circuits in
the PRIMARY CIRCUIT of DIRECT PLUG-IN EQUIPMENT, tests according to 5.3
shall be conducted, using an external protective device rated 30 A or 32 A. If these
tests fail, suitable protective devices shall be included as integral parts of the
DIRECT PLUG-IN EQUIPMENT, so that the requirements of 5.3 are met.
N/A
2.10.5.13
In Finland, Norway and Sweden, there are additional requirements for the
insulation, see 6.1.2.1 and 6.1.2.2 of this annex.
N/A
3.2.1.1
In Switzerland, supply cords of equipment having a RATED CURRENT not
exceeding 10 A shall be provided with a plug complying with SEV 1011 or IEC
60884-1 and one of the following dimension sheets:
N/A
SEV 6532-2.1991
SEV 6533-2.1991
SEV 6534-2.1991
Result - Remark
Plug Type 15
Plug Type 11
Plug Type 12
3P+N+PE
L+N
L+N+PE
Verdict
250/400 V, 10 A
250 V, 10 A
250 V, 10 A
In general, EN 60309 applies for plugs for currents exceeding 10 A. However, a 16 A
plug and socket-outlet system is being introduced in Switzerland, the plugs of which
are according to the following dimension sheets, published in February 1998:
SEV 5932-2.1998
SEV 5933-2.1998
SEV 5934-2.1998
3.2.1.1
Plug Type 25
Plug Type 21
Plug Type 23
3L+N+PE
L+N
L+N+PE
230/400 V, 16 A
250 V, 16 A
250 V, 16 A
In Denmark, supply cords of single-phase equipment having a rated current not
exceeding13 A shall be provided with a plug according to the Heavy Current
Regulations, Section 107-2-D1.
N/A
CLASS I EQUIPMENT provided with socket-outlets with earth contacts or which are
intended to be used in locations where protection against indirect contact is required
according to the wiring rules shall be provided with a plug in accordance with
standard sheet DK 2-1a or DK 2-5a.
If poly-phase equipment and single-phase equipment having a RATED CURRENT
exceeding 13 A is provided with a supply cord with a plug, this plug shall be in
accordance with the Heavy Current Regulations, Section 107-2-D1 or EN 60309-2.
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 45 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
3.2.1.1
In Spain, supply cords of single-phase equipment having a rated current not
exceeding 10 A shall be provided with a plug according to UNE 20315:1994.
Verdict
N/A
Supply cords of single-phase equipment having a rated current not exceeding 2,5 A
shall be provided with a plug according to UNE-EN 50075:1993.
CLASS I EQUIPMENT provided with socket-outlets with earth contacts or which are
intended to be used in locations where protection against indirect contact is required
according to the wiring rules, shall be provided with a plug in accordance with
standard UNE 20315:1994.
If poly-phase equipment is provided with a supply cord with a plug, this plug shall be
in accordance with UNE-EN 60309-2.
3.2.1.1
In the United Kingdom, apparatus which is fitted with a flexible cable or cord and is
designed to be connected to a mains socket conforming to BS 1363 by means of
that flexible cable or cord and plug, shall be fitted with a ‘standard plug’ in
accordance with Statutory Instrument 1768:1994 - The Plugs and Sockets etc.
(Safety) Regulations 1994, unless exempted by those regulations.
N/A
NOTE ‘Standard plug’ is defined in SI 1768:1994 and essentially means an
approved plug conforming to BS 1363 or an approved conversion plug.
3.2.1.1
In Ireland, apparatus which is fitted with a flexible cable or cord and is designed to
be connected to a mains socket conforming to I.S. 411 by means of that flexible
cable or cord and plug, shall be fitted with a 13 A plug in accordance with Statutory
Instrument 525:1997 - National Standards Authority of Ireland (section 28) (13 A
Plugs and Conversion Adaptors for Domestic Use) Regulations 1997.
N/A
3.2.4
In Switzerland, for requirements see 3.2.1.1 of this annex.
N/A
3.2.5.1
In the United Kingdom, a power supply cord with conductor of 1,25 mm2 is allowed
for equipment with a rated current over 10 A and up to and including 13 A.
N/A
3.3.4
In the United Kingdom, the range of conductor sizes of flexible cords to be
accepted by terminals for equipment with a RATED CURRENT of over 10 A up to
and including 13 A is:
N/A
• 1,25 mm2 to 1,5 mm2 nominal cross-sectional area.
4.3.6
In the United Kingdom, the torque test is performed using a socket outlet complying
with BS 1363 part 1:1995, including Amendment 1:1997 and Amendment 2:2003
and the plug part of DIRECT PLUG-IN EQUIPMENT shall be assessed to BS 1363:
Part 1, 12.1, 12.2, 12.3, 12.9, 12.11, 12.12, 12.13, 12.16 and 12.17, except that the
test of 12.17 is performed at not less than 125 °C. Where the metal earth pin is
replaced by an Insulated Shutter Opening Device (ISOD), the requirements of
clauses 22.2 and 23 also apply.
N/A
4.3.6
In Ireland, DIRECT PLUG-IN EQUIPMENT is known as plug similar devices. Such
devices shall comply with Statutory Instrument 526:1997 - National Standards
Authority of Ireland (Section 28) (Electrical plugs, plug similar devices and sockets
for domestic use) Regulations, 1997.
N/A
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 46 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
5.1.7.1
In Finland, Norway and Sweden TOUCH CURRENT measurement results
exceeding 3,5 mA r.m.s. are permitted only for the following equipment:
Verdict
N/A
• STATIONARY PLUGGABLE EQUIPMENT TYPE A that
○
is intended to be used in a RESTRICTED ACCESS LOCATION where
equipotential bonding has been applied, for example, in a
telecommunication centre; and
○
has provision for a permanently connected PROTECTIVE EARTHING
CONDUCTOR; and
○
is provided with instructions for the installation of that conductor by a
SERVICE PERSON;
• STATIONARY PLUGGABLE EQUIPMENT TYPE B;
• STATIONARY PERMANENTLY CONNECTED EQUIPMENT.
6.1.2.1
In Finland, Norway and Sweden, add the following text between the first and
second paragraph of the compliance clause:
N/A
If this insulation is solid, including insulation forming part of a component, it shall at
least consist of either
-
two layers of thin sheet material, each of which shall pass the electric
strength test below, or
one layer having a distance through insulation of at least 0,4 mm, which shall
pass the electric strength test below.
If this insulation forms part of a semiconductor component (e.g. an optocoupler),
there is no distance through insulation requirement for the insulation consisting of an
insulating compound completely filling the casing, so that CLEARANCES and
CREEPAGE DISTANCES do not exist, if the component passes the electric strength
test in accordance with the compliance clause below and in addition
-
passes the tests and inspection criteria of 2.10.11 with an electric strength
test of 1,5 kV multiplied by 1,6 (the electric strength test of 2.10.10 shall be
performed using 1,5 kV), and
-
is subject to ROUTINE TESTING for electric strength during manufacturing,
using a test voltage of 1,5 kV.
It is permitted to bridge this insulation with a capacitor complying with
EN 132400:1994, subclass Y2.
A capacitor classified Y3 according to EN 132400:1994, may bridge this insulation
under the following conditions:
-
the insulation requirements are satisfied by having a capacitor classified Y3
as defined by EN 132400, which in addition to the Y3 testing, is tested with an
impulse test of 2,5 kV defined in EN 60950-1:2006, 6.2.2.1;
-
the additional testing shall be performed on all the test specimens as
described in EN 132400;
-
the impulse test of 2,5 kV is to be performed before the endurance test in
EN 132400, in the sequence of tests as described in EN 132400.
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 47 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
6.1.2.2
In Finland, Norway and Sweden, the exclusions are applicable for
PERMANENTLY CONNECTED EQUIPMENT, PLUGGABLE EQUIPMENT TYPE B
and equipment intended to be used in a RESTRICTED ACCESS LOCATION where
equipotential bonding has been applied, e.g. in a telecommunication centre, and
which has provision for a permanently connected PROTECTIVE EARTHING
CONDUCTOR and is provided with instructions for the installation of that conductor
by a SERVICE PERSON.
N/A
7.2
In Finland, Norway and Sweden, for requirements see 6.1.2.1 and 6.1.2.2 of this
annex.
N/A
The term TELECOMMUNICATION NETWORK in 6.1.2 being replaced by the term
CABLE DISTRIBUTION SYSTEM.
7.3
In Norway and Sweden, there are many buildings where the screen of the coaxial
cable is normally not connected to the earth in the building installation.
N/A
7.3
In Norway, for installation conditions see EN 60728-11:2005.
N/A
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 48 of 57
Test Report IECEN60950_1C
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
ZC
A-DEVIATIONS (informative)
N/A
1.5.1
Sweden (Ordinance 1990:944)
N/A
Add the following:
NOTE In Sweden, switches containing mercury are not permitted.
1.5.1
Switzerland (Ordinance on environmentally hazardous substances SR 814.081,
Annex 1.7, Mercury - Annex 1.7 of SR 814.81 applies for mercury.)
N/A
Add the following:
NOTE In Switzerland, switches containing mercury such as thermostats, relays and
level controllers are not allowed.
1.7.2.1
N/A
Denmark (Heavy Current Regulations)
Supply cords of CLASS I EQUIPMENT, which is delivered without a plug, must be
provided with a visible tag with the following text:
Vigtigt!
Lederen med grøn/gul isolation
må kun tilsluttes en klemme mærket
eller
If essential for the safety of the equipment, the tag must in addition be provided with
a diagram, which shows the connection of the other conductors, or be provided with
the following text:
“For tilslutning af de øvrige ledere, se medfølgende installationsvejledning.”
1.7.2.1
Germany (Gesetz über technische Arbeitsmittel und Verbraucherprodukte (Geräteund Produktsicherheitsgesetz – GPSG) [Law on technical labour equipment and
consumer products], of 6th January 2004, Section 2, Article 4, Clause (4), Item 2).
N/A
If for the assurance of safety and health certain rules during use, amending or
maintenance of a technical labour equipment or readymade consumer product are
to be followed, a manual in German language has to be delivered when placing the
product on the market.
Of this requirement, rules for use even only by SERVICE PERSONS are not
exempted.
1.7.5
N/A
Denmark (Heavy Current Regulations)
With the exception of CLASS II EQUIPMENT provided with a socket outlet in
accordance with the Heavy Current Regulations, Section 107-2-D1, Standard Sheet
DK 1-4a, CLASS II EQUIPMENT shall not be fitted with socket-outlets for providing
power to other equipment.
1.7.13
Switzerland (Ordinance on chemical hazardous risk reduction SR 814.81, Annex
2.15 Batteries)
N/A
Annex 2.15 of SR 814.81 applies for batteries.
5.1.7.1
Denmark (Heavy Current Regulations, Chapter 707, clause 707.4)
N/A
TOUCH CURRENT measurement results exceeding 3,5 mA r.m.s. are permitted
only for PERMANENTLY CONNECTED EQUIPMENT and PLUGGABLE
EQUIPMENT TYPE B.
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 49 of 57
Test Report IECEN60950_1C
1.5.1
TABLE: List of critical components
P
Standard
(Edition / year)
object/part No. manufacturer/
trademark
type/model
technical data
mark(s) of
conformity1)
Power Adapter FSP Group Inc.
FSP045-RHC
TUV,
I/P: 100-240 Vac, EN 60950-1:
2006+A11
CB by TUV/Rh
50-60 Hz,
IEC 60950-1:2005
1.2A-0.6 A
O/P: 19 Vdc,
2.37 A (LPS),
Tma: 40 °C
Enclosure
SABIC
C6600(GG)(X)(V V-1, min 1.34 mm. UL 94
INNOVATIVE
S)
thickness. 60 °C
PLASTICS
CHINA CO., LTD.
Magnesium-Alloy --
UL
Enclosure (for Various
bottom case)
AZ91D
--
LCD Panel
InfoVision
Optoelectronics
( Kunshan ) Co.,
LTD.
M116NWR1 R0 11.6” TFT-LCD
type (LED
Backlight)
--
--
AU Optronics
Corp.
B116XW03 V0
11.6” TFT-LCD
type (LED
Backlight)
--
--
Wintek
Corporation
JA-DA0181AGN-B
11.6” TFT-LCD
type
--
--
Young Fast
Optoelectronics
Co., Ltd.
H010A
11.6” TFT-LCD
type
--
--
Hard Disk
Various
Drive (optional)
Various
5 Vdc, 1.5 A
IEC/EN 60950-1
TUV
Speakers (two Various
provided)
Various
Rated 4 ohm, 2
Watt max.
--
--
DC Fan
Techcious Co.,
Limited
HY45T-05A
5 Vdc, 0.15 A., 1.3 EN60950-1
CFM
Battery Pack
Gallopwire
Enterprise Co.,
Ltd.
82997.4 Vdc, 5000
IEC 60950-1:2005 CB by TUV/SUD
PRLUCMD5000 mAh. Tma: 45 °C Evaluated in
4
appliance for EN
60950-1/A11:2009
Pegatron
Corporation
GG99-0150
maximum
7.4 Vdc, 37 Wh.
Tma: 45 °C
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
TUV
IEC 60950-1:2005 CB by TUV/SUD
Evaluated in
appliance for EN
60950-1/A11:2009
Report reference No.: 081-100802-000
S2011.DOC
Page 50 of 57
Test Report IECEN60950_1C
object/part No. manufacturer/
trademark
type/model
technical data
Standard
(Edition / year)
mark(s) of
conformity1)
Main board
M11JB
--
--
--
-R.T.C Battery VIC-DAWN
(Lithium type) ENTERPRISE
CO., LTD. / KTS
CR2032
3 Vdc, max.
UL 1642
abnormal charging
current 10 mA
-PTC
Polyswitch for
HDMI port
(MF1)
Raychem
Corporation
miniSMDC110F 6 Vdc, 1.1 A
EN 60730-1
TUV
Bourns Inc.
MF-MSMF110
6 Vdc, 1.1 A
EN 60730-1
TUV
Polytronics
SMD1812P110T 8 Vdc, 1.1 A
Technology Corp. F
EN 60730-1
TUV
Pegatron
Corporation
-PTC
Raychem
Polyswitch for Corporation
USB port (UF4)
UL
EN 60738-1
MINISMDC260F 6 Vdc, 2.6 A
EN 60730-1
TUV
Bourns Inc.
MF-MSMF260
6 Vdc, 2.6 A
EN 60730-1
TUV
Littelfuse Inc.
1812L260
6 Vdc, 2.6 A
EN 60730-1
TUV
EN 60738-1
Polytronics
SMD1812P260T 8 Vdc, 2.6 A
Technology Corp. FT
EN 60730-1
TUV
EN 60738-1
EN 60738-1-1
-PCB
Various
Various
V-1 min., 105 °C
UL 796
UL
1
) an asterisk indicates a mark which assures the agreed level of surveillance
Supplementary information:
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 51 of 57
Test Report IECEN60950_1C
1.6.2
U (Vdc)
TABLE: Electrical data (in normal conditions)
I (A)
Irated (A)
P (W)
P
Fuse #
Ifuse (A)
Condition/status
With Battery Pack, Model GG99-0150
19
1.95
2.37
37.05
--
--
Maximum normal load with
charging empty battery pack.
19
1.33
2.37
25.27
--
--
System off with battery pack
charging mode
7.87
2.93
--
23.06
--
--
Maximum normal load with
battery pack discharge
7.04
2.95
--
20.77
--
--
System off with only Battery
charging from system
With Battery Pack, Model 8299-PRLUCMD50004
19
1.95
2.37
37.05
--
--
Maximum normal load with
charging empty battery pack.
19
1.35
2.37
25.65
--
--
System off with battery pack
charging mode
7.83
2.97
--
23.26
--
--
Maximum normal load with
battery pack discharge
7.1
2.95
--
20.95
--
--
System off with only Battery
charging from system
Supplementary information:
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 52 of 57
Test Report IECEN60950_1C
2.5
TABLE: Limited power source measurement
P
1. According to Table 2B with normal condition for J11 (USB near audio) pin 1 to pin 4
Output Voltage (Voc)
Output Current (Isc)
VA
V ac
V dc
Measured
Max Allowed
Measured
Max Allowed
Measured
≤30
≤30
5.12
≤8.0
5.2
≤100
17.24
2. According to Table 2B with normal condition for J12 (USB near HDMI) pin1 to pin 4
Output Voltage (Voc)
Output Current (Isc)
VA
V ac
V dc
Measured
Max Allowed
Measured
Max Allowed
Measured
≤30
≤30
5.12
≤8.0
5.2
≤100
17.24
3. According to Table 2B with normal condition for J124 (HDMI) pin 12 to pin 1
Output Voltage (Voc)
Output Current (Isc)
VA
V ac
V dc
Measured
Max Allowed
Measured
Max Allowed
Measured
≤30
≤30
3.22
≤8.0
0
≤100
0
4. According to Table 2B with normal condition for J124 (HDMI) pin 18 to pin 1
Output Voltage (Voc)
Output Current (Isc)
VA
V ac
V dc
Measured
Max Allowed
Measured
Max Allowed
Measured
≤30
≤30
5.08
≤8.0
2.2
≤100
8.23
5. According to Table 2B with normal condition for AJ1 (Audio) pin 1,2 to Earth
Output Voltage (Voc)
Output Current (Isc)
VA
V ac
V dc
Measured
Max Allowed
Measured
Max Allowed
Measured
≤30
≤30
0
≤8.0
0
≤100
0
6. According to Table 2B with normal condition for WWJ2 (SIM card) pin P1-P3,P6,P7 to pin P5
Output Voltage (Voc)
Output Current (Isc)
VA
V ac
V dc
Measured
Max Allowed
Measured
Max Allowed
Measured
≤30
≤30
0
≤8.0
0
≤100
0
7. According to Table 2B with normal condition for SBJ1 (Docking) pin 6,7 to pin 9
Output Voltage (Voc)
Output Current (Isc)
VA
V ac
V dc
Measured
Max Allowed
Measured
Max Allowed
Measured
≤30
≤30
3.31
≤8.0
0
≤100
0
Supplementary information:
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 53 of 57
Test Report IECEN60950_1C
8. According to Table 2B with normal condition for SBJ1 (Docking) pin 8 to pin 9
Output Voltage (Voc)
Output Current (Isc)
VA
V ac
V dc
Measured
Max Allowed
Measured
Max Allowed
Measured
≤30
≤30
8.97
≤8.0
0
≤100
0
9. According to Table 2B with normal condition for SBJ1 (Docking) pin 16 to pin 9
Output Voltage (Voc)
Output Current (Isc)
VA
V ac
V dc
Measured
Max Allowed
Measured
Max Allowed
Measured
≤30
≤30
2.2
≤8.0
0
≤100
0
10. According to Table 2B with normal condition for SBJ1 (Docking) pin 17 to pin 9
Output Voltage (Voc)
Output Current (Isc)
VA
V ac
V dc
Measured
Max Allowed
Measured
Max Allowed
Measured
≤30
≤30
2.04
≤8.0
0
≤100
0
11. According to Table 2B with normal condition for SBJ1 (Docking) pin 24 to pin 9
Output Voltage (Voc)
Output Current (Isc)
VA
V ac
V dc
Measured
Max Allowed
Measured
Max Allowed
Measured
≤30
≤30
3.35
≤8.0
0
≤100
0
12. According to Table 2B with normal condition for SBJ1 (Docking) pin 25 to pin 9
Output Voltage (Voc)
Output Current (Isc)
VA
V ac
V dc
Measured
Max Allowed
Measured
Max Allowed
Measured
≤30
≤30
2.26
≤8.0
0
≤100
0
13. According to Table 2B with normal condition for SBJ1 (Docking) pin 26 to pin 9
Output Voltage (Voc)
Output Current (Isc)
VA
V ac
V dc
Measured
Max Allowed
Measured
Max Allowed
Measured
≤30
≤30
3.37
≤8.0
0
≤100
0
Supplementary information:
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 54 of 57
Test Report IECEN60950_1C
4.5
TABLE: Thermal requirements
P
Supply voltage (V) .......................... :
⎯
A: Normal Heating (19 Vdc)
B: Battery Pack discharging only
Ambient Tmin (°C) ............................ :
--
⎯
Ambient Tmax (°C) ............................ :
--
⎯
Maximum measured temperature T of part/at::
T (°C)
Test Voltage
Allowed Tmax (°C)
A
B
--
1.Ambient
35.0
35.0
--
2.PWB near HU1
67.8
68.8
105
3.PWB near North chip
60.5
60.8
105
4.RTC body
40.6
42.8
100
5.UF4 body
53.2
53.8
85
6.Battery body
46.0
48.8
100
7.Enclosure (plastic) inside near Heat sink
52.6
53.8
60
8.Enclosure (metal) outside near Heat sink
51.3
51.8
55
9.Panel body
43.1
45.8
75
Supplementary information:
Temperature T of winding:
t1 (°C)
R1 (Ω)
t2 (°C)
R2 (Ω)
T (°C)
Allowed Insulation
class
Tmax (°C)
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Supplementary information:
The temperatures were measured by thermal couple (type K) method under worst case normal mode as
described in 1.6.2 at voltage described in 1.4.5. The worst case normal mode is defined with max load of the
adaptor.
With max. ambient temperature specified as 35 °C, therefore, the maximum temperature rise is calculated as
follows:
Components with:
- max. temp. of 105 °C (PWB)
- max. temp. of 100 °C (RTC, Battery)
- max. temp. of 85 °C (UF4)
- max. temp. of 60 °C (Plastic Enclosure)
User accessible area:
- continuously held in normal use for metal material (55 °C)
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 55 of 57
Test Report IECEN60950_1C
4.6.1 &
4.6.2
TABLE: Enclosure openings
P
Location
Size (mm)
Comments
Top
Several slot openings, each
measured max. 9.5 mm by 1.0 mm
width, see photo for the covering
areas.
No hazardous parts within 5 degrees of
projection area.
Side
--
No side openings.
Bottom
Several slot openings, each
measured max. 9.0 mm by 1.0 mm
width, see photo for the covering
areas.
Openings do not exceed 1 mm in width
regardless of length.
Openings do not exceed 1 mm in width
regardless of length.
Supplementary information:
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 56 of 57
Test Report IECEN60950_1C
5.3
TABLE: Fault condition tests
Component
No.
CPU Fan
Openings
P
Ambient temperature (°C) ................................... :
25 oC or see below
⎯
Power source for EUT: Manufacturer, model/type,
output rating ........................................................ :
See Table 1.5.1 for detail
⎯
Fault
Supply
voltage
(Vdc)
Stalled
19
Blocked
Test
time
2h
54 min
Fuse #
--
Fuse
current
(A)
Observation
--
Unit normal operating, no hazard,
no damage,
Max. temp. as below:
Ambient: 26.6 oC,
PWB near HU1: 79.0 oC
Enclosure outside near Heatsink:
54.1 oC
19
4h
38 min
--
--
Unit normal operating, no hazard,
no damage,
Max. temp. as below:
Ambient: 27.1 oC,
PWB near HU1: 76.6 oC
Enclosure outside near Heatsink:
57.1 oC
For RTC reverse test
SD1 Pin 1 to
Pin 2
s-c
19
--
--
--
Measured abnormal reverse
current = 3.2 mA
SD1 Pin 2 to
Pin 3
s-c
19
--
--
--
Measured abnormal reverse
current = 3.0 mA
SR1
s-c
19
--
--
--
Measured abnormal reverse
current = 0.01 mA
--
--
--
Output voltage measured 115 mV
For Audio port (according to EN 50332-2)
Audio output
Normal
19
Supplementary information:
Fault: s-c = short circuit,
Note:
o-c = open circuit,
o-l = over load
The maximum abnormal charging current of RTC battery is 10 mA.
TÜV SÜD Asia Ltd. Taiwan Branch
7F., No.37, Sec. 2, Zhongyang S., Rd.,
Beitou District, Taipei City, 11270, Taiwan.
Report reference No.: 081-100802-000
S2011.DOC
Page 57 of 57
Test Report IECEN60950_1C
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement