APPLICATION FOR LOW VOLTAGE DIRECTIVE On Behalf of

APPLICATION FOR LOW VOLTAGE DIRECTIVE On Behalf of
APPLICATION FOR LOW VOLTAGE DIRECTIVE
On Behalf of
Shenzhen GGMM Industrial Company Limited
M-Freedom
WS-301
Prepared for :
Shenzhen GGMM Industrial Company Limited
Room110, F518 Idea Land, Baoyuan Road, Baoan District,
Shenzhen
Prepared By :
Shenzhen TCT Testing Technology Co., Ltd.
1F, No.1 Building, Yibaolai Industrial Park, No.1 Chongqing
Road, Qiaotou Village, Fuyong Town, Baoan District, Shenzhen
Date of Test:
Mar.28, 2014 to May.09, 2014
Date of Report:
May.09, 2014
Report Number:
TCT140428011S1-1
Note: This report shall not be reproduced except in full, without the written approval of Shenzhen TCT Testing
Technology Co., Ltd. This document may be altered or revised by Shenzhen TCT Testing Technology Co., Ltd.
personnel only, and shall be noted in the revision section of the document. The test results in the report only
apply to the tested sample.
Report No.: TCT140428011S1-1
TEST REPORT
EN 60065:2002+A1:2006+A11:2008+A2:2010+A12:2011
Audio, video and similar apparatus
Safety requirements
Report reference No . .......................: TCT140428011S1-1
Tested by (+ signature)....................... Able Chen
90
.....................................................
Approved by (+ signature) .................. Jack Zhang
.....................................................
Date of issue………………………….: May.09, 2014
Testing Laboratory Name ................: Shenzhen TCT Testing Technology Co., Ltd.
Address ............................................: 1F, No.1 Building, Yibaolai Industrial Park, No.1 Chongqing Road,
Qiaotou Village, Fuyong Town, Baoan District, Shenzhen
Testing location ...............................: CBTL
CCATL
SMT
TMP
Address............................................: Same as above.
Applicant's Name .............................: Shenzhen GGMM Industrial Company Limited
Address ............................................: Room110, F518 Idea Land, Baoyuan Road, Baoan District,
Shenzhen
Standard ...........................................: EN 60065:2002+A1:2006+A11:2008+A2:2010+A12:2011
Test procedure .................................: LVD Approval
Procedure deviation .........................: N/A
Non-standard test method ...............: N/A
Test item Description........................: M-Freedom
Manufacturer name............................ : Shenzhen GGMM Industrial Company Limited
Manufacturer address......................... Building No5, Yongxin Street, Shiyan, Baoan District, Shenzhen
Trademark.......................................... : GGMM
Model and/or type reference.............. : WS-301
Rating(s) ............................................ I/P: 18V
30W
Page 2 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
Test item particulars :
Equipment mobility .................................................... : Transportable equipment
Operating condition .................................................... : Continuous
Tested for IT power systems ..................................... : N/A
IT testing, phase-phase voltage (V) ........................... : N/A
Class of equipment .................................................... : Class III
Protection against ingress of water ........................... : IPX0
Test case verdicts:
Test case does not apply to the test object ................ : N(/A.)
Test item does meet the requirement......................... : P(ass)
Test item does not meet the requirement................... : F(ail)
Testing:
Date of receipt of test item
Mar.27, 2014
Date(s) of performance of test
Mar.28, 2014 to May.09, 2014
Page 3 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
Model List
Model List:
Rating
I/P: 18V
Test Model
WS-301
Other Models
30W
N/A
1. All tests are carried out on WS-301
2. WS-301 has same diagram circuit, PCB layout, except different colour of enclosure
Label
M-Freedom
GGMM
Model: WS-301
Rated: I/P: 18V
30W
Shenzhen GGMM Industrial Company Limited
Note:
1. The height of graphical symbols shall not be less than 5 mm;
2. The height of letters and numerals shall not be less than 2 mm;
3. The main rating label was attached in enclosure,
Page 4 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
General remarks:
"(see remark #)" refers to a remark appended to the
report.
"(see appended table)" refers to a table appended to the
report.
Attached with:
A.
Equipment list
B.
Photo documentation
Throughout this report a comma is used as the decimal
separator.
The test results presented in this report relate only to the
object tested.
All is excluded test of the scope of CNAS accreditation,
the test results for this test from an accredited lab. by
CNAS.
This report shall not be reproduced except in full without
the written approval of the testing laboratory.
Page 5 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
3
General requirements
Safety class of the apparatus ..................................:
Result - Remark
Verdict
P
Class III
P
4
4.1.4
General test conditions
Ventilation instructions require the use of the test
box
P
P
5
Marking and instructions
P
Comprehensible and easily discernible
P
5.1
Permanent durability against water and petroleum
spirit
Compliance was checked by
rubbing the marking by hand
for 15 s with cloth soaked with
water and cloth soaked with
petroleum spirit, it was durable
and legible after the test
P
a) Identification, maker ............................................ :
See marking
P
b) Model number or type reference ......................... :
See product label
P
c) Class II symbol if applicable ................................ :
N/A
d) Nature of supply ................................................... :
P
e) Rated supply voltage .......................................... :
18V
f) Mains frequency if safety dependant ................... :
N/A
g) Rated current or power consumption for
apparatus supplied by supply apparatus for general
use ........................................................................... :
30W
h) Rated current or power consumption for apparatus intended for connection to an a.c. mains supply :
See product label
N/A
Measured current or power consumption ............... :
See appended table 7.1
N/A
Measured current or power consumption for
Television set ........................................................... :
Deviation % (max 10%) ........................................... :
5.2
Not exceed the marked value
by more than 10%
b) marking on loudspeaker grille, IEC 60417-5036
N/A
N/A
No hazardous live terminals
c) Markings on supply output terminals
a) Use of triangle with exclamation mark
P
N/A
a) Earth terminal
b) Hazardous live terminals
5.3
P
N/A
N/A
Such symbol is indicated on
circuit diagram for specific
components
N/A
N/A
Page 6 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
Result - Remark
5.4
Instructions for use
Reviewed English version
5.4.1
a) Mains powered equipment not exposed to
dripping or splashing. Warning concerning objects
filled with liquid, etc.
b) Hazardous live terminals, instructions for wiring
Not such terminal
N/A
N/A
Stated in user’s manual
e) Instructions for multimedia system connection
f) Special stability warning for attachment of the
apparatus to the floor/wall
P
N/A
c) Instructions for replacing lithium battery
d) Class I earth connection warning
Verdict
N/A
P
Not fixed installation
N/A
g) Warning: battery exposure to heat
N/A
h) Warning: protective film on CRT face
N/A
a-b) Disconnect device: plug/coupler or all-pole
mains switch location, accessibility and markings
N/A
c) Instructions for permanently connected equipment
N/A
Marking, signal lamps or similar for completely
disconnection from the mains
N/A
6
Hazardous radiation
N/A
6.1
Ionizing radiation <36pA/kg (0,5 mR/h)
5.4.2
There is no CRT. No Ionizing
Radiation generated
Ionizing radiation under fault condition
6.2
Laser radiation, emission limits to IEC60825-1:2007
...................................................................................:
N/A
N/A
No laser radiation
Emission limits under fault conditions ......................:
N/A
N/A
7
Heating under normal operating conditions
P
7.1
Temperature rises not exceeding specified values;
fuse links and other protective devices defeated
See appended table 7.1
P
7.1.1
Temperature rise of accessible parts
See appended table 7.1
P
7.1.2
Temperature rise of parts providing electrical
insulation
See appended table 7.1
N/A
7.1.3
Temperature rise of parts acting as a support or as a See appended table 7.1
mechanical barrier
N/A
7.1.4
Temperature rise of windings
N/A
7.1.5
Parts not subject to a limit under 7.1.1 to 7.1.4
See appended table 7.1
P
Page 7 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
7.2
Softening temperature of insulating material
supporting parts conductively connected to the
mains carrying a current > 0.2 A at least 150 ℃
8
Constructional requirements with regard to the protection against electric
shock
P
8.1
Conductive parts covered by lacquer, paper,
untreated textile oxide films and beads etc.
considered to be bare
P
8.2
No shock hazard when changing voltage setting
device, fuse-links or handling drawers etc.
8.3
Insulation of hazardous live parts not provided by
hygroscopic material
No such material
N/A
8.4
No risk of electric shock from accessible parts or
from parts rendered accessible following the
removal of a cover which can be removed by hand
No cover can be removed by
hand
N/A
8.5
Class I equipment.
N/A
Basic insulation between hazardous live parts and
earthed accessible parts
N/A
Resistors bridging basic insulation complying with
14.1 a)
N/A
Capacitors bridging basic insulation complying with
14.2.1 a)
N/A
Protective earthing terminal
N/A
8.6
8.7
Class II equipment and Class II constructions within
Class I equipment
Result - Remark
Verdict
N/A
Class III equipment
N/A
Class III equipment
N/A
Double or reinforced insulation between hazardous
live parts and accessible parts
N/A
Components bridging double or reinforced insulation
complying with 14.1 a) or 14.3
N/A
Basic insulation bridged by components complying
with 14.3.4.3.
N/A
Basic and supplementary insulation each being
bridged by a capacitor complying with 14.1 a)
N/A
Double or reinforced insulation being bridged with 2
capacitors in series complying with 14.2.1 a)
No used bridge capacitor
N/A
Double or reinforced insulation being bridged with a
single capacitor complying with 14.2.1 b)
No used bridge capacitor
N/A
This clause is void
—
Page 8 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
8.8
Basic or supplementary insulation > 0,4 mm (mm)..:
N/A
Reinforced insulation > 0,4 mm (mm) .....................:
N/A
Thin sheet insulation (excluding non-separable thin
sheet insulation. See 8.22)
N/A
Basic or supplementary insulation, at least two
layers, each meeting 10.3
N/A
Basic or supplementary insulation, three layers any
two of which meet 10.3
N/A
Reinforced insulation, two layers each of which meet
10.3
N/A
Reinforced insulation, three layers any two which
meet 10.3
N/A
Adequate insulation between internal hazardous live
conductors and accessible parts
N/A
Adequate insulation between internal hazardous live
parts and conductors connected to accessible parts
N/A
Double insulation between conductors connected to
the mains and accessible parts.
N/A
Double insulation between internal hazardous live
parts and conductors connected to accessible parts.
N/A
8.9
8.10
8.11
Result - Remark
Verdict
Detaching of wires
No risk of any wire becoming
detached.
N/A
No undue reduction of creepages or clearance
distances if wires become detached
Internal wirings were well
routed and secured
N/A
Vibration test carried out ..........................................:
N/A
8.12
This clause is void
—
8.13
Adequate fastening of windows, lenses, lamp covers
etc. (pull test 20 N for 10 s)
N/A
8.14
Adequate fastening of covers (push/pull test 50 N for
10 s)
N/A
8.15
No risk of damage to the insulation of internal wiring
due to hot parts or sharp edges
8.16
Only special supply equipment can be used
N/A
8.17
Insulated winding wire without additional interleaved
insulation
N/A
8.18
Endurance test as required by 8.17
N/A
No risk of damage to the
insulation of internal wiring due
to high temperature, sharp
edges or pinches
P
Page 9 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
Result - Remark
8.19
Disconnection from the mains
Non-detachable power supply
with plug
8.19.1
Disconnect device
N/A
All-pole switch or circuit breaker with >3mm contact
separation
N/A
8.19.2
Mains switch ON indication
N/A
8.20
Switch not fitted in the mains cord
N/A
8.21
Bridging components comply with clause 14
N/A
8.22
Non-separable thin sheet material
N/A
9
Electric shock hazard under normal operating conditions
N/A
9.1
Testing on the outside
N/A
9.1.1
For voltages >1000 V ac or >1500 V dc complies
with clause 13.3.1 for basic insulation
9.1.1.1
a) Open circuit voltages
N/A
b) Touch current measured from terminal devices
using the network in annex D ..................................:
N/A
c) Discharge not exceeding 45 μC
N/A
d) Energy of discharge not exceeding 350 mJ
N/A
9.1.1.2
Test with test finger and test probe
N/A
9.1.2
No hazardous live shafts of knobs, handles or levers
N/A
9.1.3
Ventilation holes and other holes tested by means of
4 mm x 100 mm test pin
N/A
9.1.4
Terminal devices tested with 1 mm x 20 mm test pin
(10 N); test probe D of IEC 61032
N/A
Terminal devices tested with 1 mm x 100 mm
straight wire (1 N); test probe D of IEC 61032
N/A
No such high voltage
N/A
N/A
9.1.5
Pre-set controls tested with 2.5 mm x 100 mm test
pin (10 N); test probe C of IEC 61032
9.1.6
No shock hazard due to stored charge on withdrawal No used X-capacitor
of the mains plug; voltage (V) after 2 s ....................:
N/A
If C is not greater than 0,1 μF no test needed
N/A
Resistance to external forces
N/A
a) Test probe 11 of IEC 61032 for 10 s (50 N)
N/A
b) Test hook of fig. 4 for 10 s (20 N)
N/A
c) 30 mm diameter test tool for 5 s (100 or 250 N)
N/A
9.1.7
No Pre-set controls
Verdict
N/A
Page 10 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
Result - Remark
9.2
No hazard after removing a cover by hand
Apparatus covers are not
removable by hand
10
Insulation requirements
P
10.1
Insulation resistance (MΩ) at least 2 MΩ min. after
surge test for basic and 4 MΩ min. for reinforced
insulation ...................................................................:
P
10.2
Humidity treatment 48 h or 120 h ............................:
10.3
Insulation resistance and dielectric strength between See appended table 10.3
mains terminals
48h /95%
Verdict
N/A
P
P
Insulation Resistance and dielectric strength across
BASIC or SUPPLEMENTARY insulation (Class I)
N/A
Insulation resistance and dielectric strength across
REINFORCED insulation (Class II)
N/A
11
Fault conditions
P
11.1
No shock hazard under fault condition
P
11.2
Heating under fault condition
See appended table 11.2
P
Flames extinguish within 10 seconds
No any flames during fault
conditions testing
P
No hazard from softening solder
Solder did not become
softened or fluid during fault
conditions testing.
P
Soldered terminations not used as protective
mechanism
No soldered termination used
as protective mechanism in the
EUT.
P
11.2.1
Measurement of temperature rises
See appended table 11.2
P
11.2.2
Temperature rise of accessible parts
See appended table 11.2
P
11.2.3
Temperature rise of parts, other than windings and
printed boards, providing electrical insulation
See appended table 11.2
P
11.2.4
Temperature rise of parts acting as a support or
mechanical barrier
11.2.5
Temperature rise of windings
11.2.6
Temperature rise of printed boards shall not exceed
the limits of table 3 by max. 100 K for max. 5 min
Printed circuit boards (PCB) classified as V-0
according to 60695-11-10 or Clause G.1 may
exceed the limit in table 3 in case a) and b):
N/A
See appended table 11.2
N/A
P
N/A
Page 11 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
Result - Remark
Verdict
a) Temperature rise of printed circuit boards
exceeding the limits of table 3 by not more than
100 K for an area not greater than 2 cm² ................:
N/A
b) Temperature rise of printed circuit boards
exceeding the limits of table 3 up to 300 K for an
area not greater than 2 cm² for a maximum of 5 min
N/A
Meets all the special conditions if conductors on
printed circuit boards are interrupted
N/A
Class I protective earthing maintained
N/A
11.2.7
Temperature rise of parts not subject to the limits of (see appended table 7.1)
11.2.1 to 11.2.6 shall not exceed the limits in table 3,
item e), "Fault conditions".
P
12
Mechanical strength
P
12.1.1
Bump test where mass >7 kg
<7Kg
12.1.2
Vibration test
Examination of the apparatus
revealed that no parts or
connections were loosened
P
12.1.3
Impact hammer test
0.5J, three blows, no damage
and the apparatus can
withstand the dielectric
strength test as specified in
10.3
P
Steel ball test
2J applied, no damage and the
apparatus can withstand the
dielectric strength test as
specified in 10.3.
P
12.1.4
Drop test for portable apparatus where mass ≤ 7 kg
<7Kg
P
12.1.5
Thermoplastic enclosures stress relief test
70°C, 7hours, No damage to
the enclosure and no parts
become hazardous live
P
12.2
Fixing of knobs, push buttons, keys and levers
Push buttons are fastened that
their use did not impair the
protection against electric
shock
P
12.3
Remote controls with hazardous live parts
12.4
Drawers (pull test 50 N, 10 s)
12.5
Antenna coaxial sockets providing isolation
N/A
12.6
Telescoping or rod antennas construction
N/A
12.6.1
Telescoping or rod antennas securement
N/A
N/A
N/A
No drawer
N/A
Page 12 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
Result - Remark
Verdict
13
Clearances and creepage distances
13.1
Clearances in accordance with 13.3
Class III equipment
N/A
Creepage distances in accordance with 13.4
See appended table 13.3 &
13.4
N/A
N/A
13.2
Determination of working voltage
N/A
13.3
Clearances
13.3.1
General
N/A
13.3.2
Circuits conductively connected to the mains comply
with table 8 and, where applicable, table 9 ..............:
N/A
13.3.3
Circuits not conductively connected to the mains
comply with table 10
N/A
13.3.4
Measurement of transient voltages
N/A
13.4
Creepage distances
See appended table 13.3 &
13.4
See appended table 13.3 &
13.4.
N/A
N/A
Creepage distances greater than table 11 minimum
values
N/A
13.5
Printed boards
N/A
13.5.1
Clearances and creepage distances between
conductors on printed circuit boards, one of which
may be conductively connected to the mains, as in
fig. 10
N/A
13.5.2
Type B coated printed circuit boards complying with
IEC 60664-3 (basic insulation only)
13.6
Conductive parts along uncemented joints
clearances and creepage distances comply with
13.3 and 13.4
N/A
Conductive parts along reliably cemented joints
comply with 8.8
N/A
Temperature cycle test and dielectric strength test
N/A
500V test for transformers, magnetic coupler and
similar devices, if insulation is relied upon for safety
N/A
13.7
Enclosed, enveloped or hermetically sealed parts
not conductively connected to the mains, clearances
and creepage distances as in table 12
N/A
13.8
Parts filled with insulating compound, meeting the
requirements of 8.8
N/A
No such printed board
N/A
Page 13 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
14
Components
14.1
Resistors
14.2
Result - Remark
Verdict
N/A
No such resistors
N/A
a) Resistors between hazardous live parts and
accessible metal parts
N/A
b) Resistors, other than between hazardous live
parts and accessible parts
N/A
Resistors separately approved ................................:
N/A
Capacitors and RC units
No such capacitors
N/A
Capacitors separately approved ..............................:
See below
N/A
14.2.1
Y capacitors tested to IEC 60384-14:2005 .............:
No such capacitors
N/A
14.2.2
X capacitors tested to IEC 60384-14:2005 .............:
No such capacitors
N/A
14.2.3
Capacitors operating at mains frequency but not
connected to the mains: tests for X2 .......................:
No such capacitor
N/A
14.2.5
Capacitors with volume exceeding 1750 mm³, where Capacitor by metal enclosure
short-circuit current exceeds 0,2 A: compliance with
IEC 60384-1, 4.38 category B or better ...................:
N/A
Capacitors with volume exceeding 1750 mm³,
mounted closer to a potential ignition source than
table 5 permits: compliance with IEC 60384-1, 4.38
category B or better ..................................................:
N/A
14.3
Shielded by a barrier acc. to 20.1.4/ table 21 or
metal .........................................................................:
No such capacitor
N/A
Inductors and windings
No such inductors
N/A
Comply with IEC 61558-1, IEC 61558-2
(as relevant) and clause 20.1.4
14.3.1
Transformers and inductors marked with
manufacturer's name and type ................................:
N/A
No Transformers
N/A
Transformers and inductors separately approved ..:
N/A
General
N/A
Insulation material complies with clause 20.1.4
N/A
14.3.3
Constructional requirements
N/A
14.3.3.1
Clearances and creepage distances comply with
clause 13
N/A
14.3.3.2
Transformers meet the constructional requirements
14.3.4
Separation between windings
14.3.2
Considered
N/A
N/A
Page 14 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
Result - Remark
14.3.4.1
Class II transformers have adequate separation
between hazardous live parts and accessible parts
(double or reinforced insulation) ...............................:
Double or reinforced insulation
used between hazardous live
parts and accessible parts
Coil formers and partition walls > 0,4 mm
Verdict
N/A
N/A
14.3.4.2
Class I transformers, with basic insulation and
protective screening only if all 7 conditions of
14.3.4.2 are met
14.3.4.3
Separating transformers with at least basic insulation
N/A
14.3.5
Insulation between HAZARDOUS LIVE parts and
ACCESSIBLE parts
N/A
14.3.5.1
Class II transformers have adequate insulation
between hazardous live parts and accessible parts
(double or reinforced insulation)
N/A
Coil formers and partition walls > 0,4 mm
N/A
Class I transformers have adequate insulation
between hazardous live parts and accessible
conductive parts or those conductive parts or
protective screens connected to a protective earth
terminal
N/A
Winding wires connected to protective earth have
adequate current-carrying capacity
N/A
High voltage components
N/A
High-voltage components and assemblies: U > 4 kV
(peak) separately approved
N/A
Component meets category V-1 of IEC 60707
N/A
14.4.1
High voltage transformers and multipliers tested as
part of the submission
N/A
14.4.2
High voltage assemblies and other parts tested as
part of the submission
N/A
14.5
Protective devices
14.3.5.2
14.4
No such transformer used
See below
Protective devices used within their ratings
External clearances and creepage distances meet
requirement of clause 13 for the voltage across the
device when opened
14.5.1.1
14.5.1.2
N/A
N/A
N/A
See appended table 13.3,
13.4.
N/A
a) Thermal cut-outs separately approved
N/A
b) Thermal cut-outs tested as part of the submission
N/A
a) Thermal links separately approved
N/A
b) Thermal links tested as part of the submission
N/A
Page 15 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
Result - Remark
Verdict
14.5.1.3
Thermal devices re-settable by soldering
14.5.2.1
Fuse-links in the mains circuit according to IEC
60127
14.5.2.2
Correct marking of fuse-links adjacent to holder .....:
N/A
14.5.2.3
Not possible to connect fuses in parallel .................:
N/A
14.5.2.4
Not possible to touch hazardous live parts when
replacing fuse-links without the use of a tool ..........:
Tool required
N/A
14.5.3
PTC thermistors comply with IEC 60730-1:2007
No such PTC used
N/A
N/A
See appended table 14
N/A
PTC devices (15 W) category V-1 or better
N/A
14.5.4
Circuit protectors have adequate breaking capacity
and their position is correctly marked
N/A
14.6
Switches
N/A
14.6.1 a)
Separate testing to IEC 61058-1 including:
- 10 000 operations
- Normal pollution suitability
- Make and break speed independent of speed of
actuation
V-0 compliance with annex G, G.1.1
N/A
14.6.1 b)
Tested in the apparatus:
N/A
Switch controlling > 0.2A with open contact voltage
> 35 V (peak)/24 V dc complying with 14.6.3, 14.6.4
and V-0 in annex G, G.1.1
N/A
Switch controlling > 0.2A with open contact voltage
< 35 V (peak)/24 V dc complying with 14.6.3 and V-0
in annex G, G.1.1
N/A
Switch controlling < 0.2A with open contact voltage
> 35 V (peak)/24 V dc complying with 14.6.4 and
V-0 in annex G, G.1.1
N/A
14.6.2
Switch tested to 14.6.1 b) constructed to IEC 610581 subclause 13.1 and has making/breaking action
independent of speed of actuation
N/A
14.6.3
Switch tested to 14.6.1 b) compliant with IEC 610581 subclause 16.2.2 d) and m) not attaining
excessive temperatures in use
N/A
14.6.4
Switch tested to 14.6.1 b) has adequate dielectric
strength
N/A
14.6.5
Mains switch controlling mains socket outlets
additional tests to IEC 61058-1
N/A
Page 16 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
Result - Remark
Socket outlet current marking correct
14.7
Safety interlocks
N/A
No safety interlocks used
Safety interlocks to 2.8 of IEC 60950-1
14.8
Voltage setting devices and the like
Verdict
N/A
N/A
No voltage setting devices
N/A
Voltage setting device not likely to be changed
accidentally
N/A
14.9
Motors
N/A
14.9.1
Endurance test on motors
N/A
Motor start test
N/A
Dielectric strength test
N/A
14.9.2
Not adversely affected by oil or grease etc.
N/A
14.9.3
Protection against moving parts
N/A
14.9.4
Motors with phase-shifting capacitors, three-phase
motors and series motors meet clause. B.8, B.9 and
B.10 of IEC 60950-1, Annex B
N/A
14.10
Batteries
14.10.1
Batteries mounted with no risk of accumulation of
flammable gases
N/A
14.10.2
No possibility of recharging non-rechargeable
batteries
N/A
14.10.3
Recharging currents and times within manufacturers
limits
N/A
Lithium batteries discharge and reverse currents
within the manufacturers limits
N/A
14.10.4
Battery mould stress relief
N/A
14.10.5
Battery drop test
N/A
14.11
Optocouplers
N/A
a) Comply with 13.6 (jointed insulation) and N.2.1
N/A
b) Comply with IEC 60747-5-5:2007
N/A
Alternative to a) and b) optocoupler comply with 13.8
N/A
a) Comply with 13.6 (jointed insulation) and N.2.1
N/A
Surge suppression varistors
N/A
Comply with IEC 61051-2
N/A
14.12
See a table of 14.10
N/A
Page 17 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
Result - Remark
Verdict
Not connected between mains and accessible parts
except for earthed parts of permanently connected
apparatus
N/A
Complies with the current pulse, fire hazard and
thermal stress requirements of 14.12
N/A
15
Terminals
P
15.1.1
Mains plug, appliance inlet, interconnection couplers Refer to appended table 14
and mains socket-outlet meet the appropriate
standard
P
15.1.2
Overloading of plugs or appliance inlets prevented if
the apparatus has mains socket outlets
N/A
Overloading of internal wiring prevented if the
apparatus has mains socket outlets
N/A
Connectors for antenna, earth, audio, video or
data
P
No risk of insertion in mains socket-outlets
No risk of insertion into audio- or video- outlets
marked with the symbol of 5.2
N/A
P
15.1.3
Output terminals of a.c. adaptors or similar devices
not compatible with household mains socket-outlets
N/A
15.2
Provision for protective earthing
N/A
Accessible conductive parts of Class I equipment
reliably connected to earth terminal, within
equipment
N/A
Protective earth conductors correctly coloured
N/A
Equipment with non-detachable mains cord provided No such equipment
with separate protective earth terminal near mains
input
N/A
Protective earth terminal resistant to corrosion
N/A
Earth resistance test: < 0,1 Ω at 25 A ....................:
N/A
15.3
Terminals for external flexible cords and for
permanent connection to the mains supply
N/A
15.3.1
Adequate terminals for connection of permanent
wiring
N/A
15.3.2
Reliable connection of non-detachable cords
N/A
Not soldered to conductors of a printed circuit board
N/A
Adequate clearances and creepage distances
between connections should a wire break away
N/A
Page 18 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
Result - Remark
Wire secured by additional means to the
conductor
Verdict
N/A
No such screws and nuts
15.3.3
Screws and nuts clamping conductors have
adequate threads: ISO 261, ISO 262 or similar
15.3.4
Soldered conductors wrapped around terminal prior
to soldering or held in place by additional means
N/A
Clamping of conductor and insulation if not soldered
or held by screws
N/A
15.3.5
Terminals allow connection of appropriate crosssectional area of conductors, for the rated current of
the equipment
N/A
15.3.6
Terminals to 15.3.3 have sizes required by table 16
N/A
15.3.7
Terminals clamp conductors between metal and
have adequate pressure
N/A
Terminals designed to avoid conductor slipping out
when tightened or loosened
N/A
Terminals adequately fixed to avoid loosening when
the clamping is tightened or loosened and stress on
internal wiring is avoided
N/A
15.3.8
Terminals carrying a current more than 0,2 A:
contact pressure not transmitted by insulating
material except ceramic
N/A
15.3.9
Termination of non-detachable cords: wires
terminated near to each other
N/A
Terminals located and shielded: test with 8 mm
strand
N/A
Not direct plug-in equipment
N/A
15.4
Devices forming a part of the mains plug
N/A
15.4.1
No undue strain on mains socket-outlets
N/A
15.4.2
Device complies with standard for dimensions of
mains plugs
N/A
15.4.3
Device has adequate mechanical strength (tests
a,b,c)
N/A
16
External flexible cords
N/A
16.1
Mains cords sheathed type, complying with
IEC 60227 for PVC or IEC 60245 for synthetic
rubber cords .............................................................:
N/A
Non-detachable cords for Class I have green/yellow
core for protective earth
N/A
Page 19 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
16.2
Mains cords conductors have adequate crosssectional area for rated current consumption of the
equipment
N/A
16.3
a) Flexible cords not complying with 16.1, used for
interconnections between separate units of
equipment used in combination and carrying
hazardous live voltages, have adequate dielectric
strength
N/A
b) Flexible cords not complying with 16.1, withstand
bending and mechanical stress (3.2 of IEC 60227-2)
N/A
16.4
Flexible cords used for connection between
equipment have adequate cross-sectional areas to
avoid temperature rise under normal and fault
conditions
N/A
16.5
Adequate strain relief on external flexible cords
N/A
Not possible to push cord back into equipment
Result - Remark
A strain-relief bushing was
provided to prevent the push
back of the power supply cord
Verdict
N/A
Strain relief device unlikely to damage flexible
cord
N/A
For mains cords of Class I equipment, hazardous
live conductors become taut before earth conductor
N/A
16.6
Apertures for external flexible cord: no risk of
damage to the cord during assembly or movement
in use
N/A
16.7
Transportable musical instruments and amplifiers
fitted with detachable cord set with appliance inlet to
IEC 60320-1
N/A
Transportable musical instruments and amplifiers
fitted with detachable cord sets or with means of
stowage to protect the cord
N/A
17
Electrical connections and mechanical fixings
P
17.1
Torque test to table 20
P
- screws into metal: 5 times
- screws into non-metallic material:10 times
N/A
P
17.2
Correct introduction into female threads in nonmetallic material
N/A
17.3
Cover fixing screws: captive
N/A
Non-captive fixing screws: no hazard when replaced
by a screw whose length is 10 times its diameter
N/A
Page 20 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
Result - Remark
17.4
No loosening of conductive parts carrying a current
> 0,2 A
N/A
17.5
No contact pressure
Contact pressure not transmitted through plastic
other than ceramic for connections carrying a current transmitted through insulating
material
> 0,2 A
N/A
17.6
Stranded conductors of flexible supply cords
carrying a current > 0,2 A with screw terminals not
consolidated by solder
N/A
17.7
Cover fixing devices other than screws have
adequate strength and their positioning is
unambiguous
N/A
17.8
Fixing devices for detachable legs or stands
provided
17.9
Internal pluggable connections, affecting safety,
unlikely to become disconnected
N/A
18
Mechanical strength of picture tubes and protection against the effects of
implosion
N/A
18.1
Picture tube separately approved to IEC 61965 ... :
N/A
Picture tube separately approved to 18.2 ............. :
N/A
18.2
Non-intrinsically protected tubes tested to 18.2
N/A
19
Stability and mechanical hazards
No detachable legs or stands
provided
Verdict
N/A
P
Mass of the equipment exceeding 7 kg ................. :
<7Kg
N/A
Apparatus intended to be fastened in place –
suitable instructions ................................................ :
Not intended to be fastened in
place-suitable
N/A
19.1
Test on a plane, inclined at 10o to the horizontal
No overturn
N/A
19.2
100 N force applied vertically downwards
No overturn
N/A
19.3
100 N force, or 13% of weight, applied horizontally
to point of least stability
19.4
Edges or corners not hazardous
All edges and corners are
judged to be sufficiently well
rounded so as not to constitute
a hazard
19.5
Glass surfaces (exc.laminated) with an area
exceeding 0,1 m² or maximum dimension
> 450 mm, pass the test of 19.5.1
No glass surfaces
19.6
Wall or ceiling mountings adequate
N/A
P
N/A
N/A
Page 21 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
Result - Remark
Verdict
20
Resistance to fire
P
20.1
Electrical components and mechanical parts
P
a) Exemption for components contained in an
enclosure of material V-0 to IEC 60695-11-10 with
openings not exceeding 1 mm in width
N/A
b) Exemption for small components as defined in
20.1
N/A
20.1.1
Electrical components meet the requirements of
Clause 14 or 20.1.4
P
20.1.2
Insulation of internal wiring working at voltages
> 4 kV or leaving an internal fire enclosure, or
located within the areas mentioned in Table 21, not
contributing to the spread of fire
20.1.3
Material of printed circuit boards on which the
PCB base material is of
available power exceeds 15 W at a voltage between flammability category V-0
50 V and 400 V (peak) a.c. or d.c. meets V-1 or
better to IEC 60707, unless used in a fire enclosure
N/A
Material of printed circuit boards on which the
available power exceeds 15 W at a voltage >400 V
(peak) a.c. or d.c. meets V-0 to IEC 60707
PCB base material is of
flammability category V-0
N/A
Components and parts not covered by 20.1.1,
20.1.2 and 20.1.3 (other than fire enclosures)
mounted nearer to a potential ignition source than
the distances in Table 21 comply with the relevant
flammability category in Table 21
V-0 flammability plastic
enclosure used.
20.1.4
20.2
20.2.1
20.2.2
20.2.3
No wires working at voltages >
4kV, Insulation of all wires is
PVC material
N/A
P
Components and parts as above but shielded from a No barrier used
potential ignition source, with the barrier area in
accordance with Table 21 and fig. 13
No voltages exceeding 4kV
Apparatus with voltages >4kV under normal
operating conditions and distances to the enclosure
exceed those specified Table 21, flammability
classification HB40 or better is required for the
enclosure
V-0 flammability plastic
Fire enclosure
enclosure used.
No voltages exceeding 4kV
Potential ignition sources with open circuit voltage
> 4 kV (peak) a.c. or d.c. contained in a fire
enclosure to V-1
Internal fire enclosures with openings not exceeding No internal fire enclosure
1 mm in width and with openings for wires
completely filled
N/A
Requirements of 20.2.1 and 20.2.2 met by an
internal fire enclosure
N/A
N/A
P
N/A
N/A
Page 22 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
A
Annex A, Additional requirements for apparatus with protection against
splashing water
N/A
A.5
Marking and instructions
N/A
A.5.1
j) Marked with IPX4 (IEC 60529), 5.4.1 a) does not
apply
N/A
A.10
Insulation requirements
N/A
A.10.2
Splash and humidity treatment
N/A
A.10.2.1
Enclosure provides protection against splashing
water
N/A
A.10.2.2
Humidity treatment carried out for 7 days
N/A
B
ANNEX B: APPARATUS TO BE CONNECTED TO THE TEL ECOMMUNICATION
NETWORKS
(No such connection means)
Where the separation of TNV circuits from other
circuits relies on protective earthing the
instructions make it clear that protective earthing
is essential
TNV circuits separated from the mains circuit and
from hazardous live parts by either
double or reinforced insulation
basic insulation with earthed protective screening
N/A
TNV circuits separated from circuits other than
those in B.8.1 and from accessible conductive
parts by basic insulation meeting the requirements
for clearances and creepage distances for the
voltages concerned
TNV circuit terminals contacts which cannot be
touched by probe B.1, exempt from the
requirements inaccessible terminal contacts in
9.1.1
Insulation between TNV terminals and antenna
terminals (including interconnection terminals
which may be connected to equipment with
antenna terminals) withstands the 50 discharges
of 10.1
Surge suppressors between TNV circuits and
other parts of the equipment have breakdown
voltage at least 1,8 times the mains voltage
N/A
B.5.4.1
B.8.1
B.8.2
B.9.1.1
B.10.1
B.14.12
Result - Remark
Verdict
N/A
N/A
N/A
N/A
N/A
N/A
N/A
C
ANNEX C: BAND-PASS FILTER FOR WIDE-BAND NOISE MEASUREMENT
N/A
D
ANNEX D: MEASURING NETWORK FOR TOUCH CURRENTS (see 9.1.1.1)
Measuring instrument
As in figure D.1 used.
N/A
N/A
Page 23 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
E
ANNEX E: MEASURENENT OF CLEARANCES AND CREEPAGE DISTANCES
(see 13)
N/A
F
ANNEX F: TABLE OF ELECTROCHEMICAL POTENTIALS
N/A
G
ANNEX G: FLAMMABILITY TEST METHODS
H
ANNEX H: INSULATED WINDING WIRES FOR USE WITHOUT INTERLEAVED
INSULATION
Intentionally kept free
Type tests
Dielectric strength
Flexibility and adherence
Heat shock
Retention of dielectric strength after bending
Testing during manufacture
Routine test
Sampling test
N/A
N/A
J.4
J.5
J.6
ANNEX J: ALTERNATIVE METHOD FOR DETERMINING MINIMUM
CLEARANCES
Summary of the procedure of for determining
minimum clearances
Determination of mains transient voltage
Determination of telecommunication network
transient voltage
Determination of required withstand voltage
Measurement of transient levels
Determination of minimum clearances
K
ANNEX K: IMPULSE TEST GENERATORS
N/A
M
ANNEX M: EXAMPLES OF REQUIREMENTS FOR QUALITY CONTROL
PROGRAMMES
Reduced clearances (see 13.3)
N/A
ANNEX M: ROUTINE TESTS
Tests during the production process
Correct polarity and connection of components or
subassemblies
Correct values of components
Protective earthing connection of screens and
metal barriers
Correct position of internal wiring
Correct fit of internal plug connections
Safety relevant markings inside the apparatus
Correct mounting of mechanical parts
Tests at the end of the production process
N/A
N/A
N/A
H.1
H.2
H.2.1
H.2.2
H.2.3
H.2.4
H.3
H.3.1
H.3.2
J
J.1
J.2
J.3
M.1
N
N.1
N.1.1
N.1.2
N.1.3
N.1.4
N.1.5
N.1.6
N.1.7
N.2
Result - Remark
Verdict
P
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Page 24 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
N.2.1
N.2.2
N.2.3
Dielectric strength test
Protective earthing connection
Safety relevant marking on the outside of the
apparatus
Result - Remark
IEC 60065, GROUP DIFFERENCES (CENELEC common modifications (EN))
Add the following annexes:
Annex ZA (normative) Other international publications quoted in this standard with
the references of the relevant European publications (See the CB Bulletin)
Annex ZB (nominative) Special national conditions
Annex ZC (informative) A-deviations
Definition
Add after the definition 2.2.12 the following new
2.2.Z1
definition:
(A11:2008) PORTABLE SOUND SYSTEM
small battery powered audio equipment:
whose prime purpose is to listen to recorded or
broadcasted sound; and
that uses headphones or earphones that can be
worn in or on or around the ears; and
that allows the user to walk around
NOTE Examples are mini-disc or CD players, MP3
audio players or similar equipment.
2.2
In EN 60065:2002/A11:2008
(A12:2011) Delete the definition 2.2.Z1
3.1
Add the following indent at the end of the list
Exposure to excessive sound pressures from
headphones or earphones
NOTE A new method of measurement is described
in EN 50332-1, Sound system equipment: MFreedoms and earphones associated with portable
audio equipment
– Maximum sound pressure level measurement
methodology and limit considerations – Part 1:
General method for ”one package equipment”, and
in EN 50332-2, Sound system equipment: MFreedoms and earphones associated with portable
audio equipment – Maximum sound pressure level
measurement methodology and limit considerations
– Part 2: Guidelines to associate sets with
headphones coming from different manufacturers.
3.1
In EN 60065:2002
(A12:2011) Delete the addition of indent regarding sound
pressure excessive
3.Z1
After 3.2 add a new clause 3.Z1:
(A2:2010) To protect against excessive current, short-circuits
and earth faults in MAINS, protective devices shall
be included either as integral parts of the
equipment or as parts of the building installation,
subject to the following, a), b) and c):
Contents
Verdict
N/A
N/A
N/A
P
P
N/A
N/A
N/A
N/A
N/A
Page 25 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
4.1.1
Requirement + Test
Result - Remark
a) except as detailed in b) and c), protective
devices necessary to comply with the requirements
of 11 shall be included as parts of the equipment;
b) for components in series or parallel with the
mains input to the equipment such as the supply
cord, appliance coupler, r.f.i. filter and switch, shortcircuit and earth fault protection may be provided
by protective devices in the building installation;
c) it is permitted for equipment supplied via an
industrial mains plug or for PERMANENTLY
CONNECTED APPARATUS, to rely on dedicated
over current and short-circuit protection in the
building installation, provided that the means of
protection, e.g. fuses or circuit breakers, is fully
specified in the installation instructions.
If reliance is placed on protection in the building
installation, the installation instructions shall so
state, except that for not via an industrial mains
plug or for PERMANENTLY CONNECTED
APPARATUS the building installation shall be
regarded as providing protection in accordance
with the rating of the wall socket outlet.
Replace the text of the note by: NOTE For
ROUTINE TEST reference is made to EN 50514.
Verdict
N/A
5.4.1
Modify indent za) as follows:
za)
za) For a PORTABLE SOUND SYSTEM, a warning
(A11:2008) that excessive sound pressure from earphones and
headphones can cause hearing loss.
N/A
5.4.1
In EN 60065:2002/A1:2006 and EN
(A12:2011) 60065;2002/A11:2008
Delete the modification in indent za)
Add the following clause and annex to the excisting
standard and amendments
Zx Protection against excessive sound pressure from personal music players
N/A
N/A
Page 26 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
Result - Remark
Zx.1 General
This sub-clause specifies requirements for protection
against excessive sound pressure from
personal music players that are closely coupled to the
ear. It also specifies requirements for
earphones and headphones intended for use with
personal music players.
Verdict
N/A
A personal music player is a portable equipment for
personal use, that:
is designed to allow the user to listen to recorded or
broadcast sound or video; and
primarily uses headphones or earphones that can be
worn in or on or around the ears; and
allows the user to walk around while in use.
NOTE 1 Examples are hand-held or body-worn portable
CD players, MP3 audio players, mobile phones with MP3
type
features, PDA’s or similar equipment.
A personal music player and earphones or headphones
intended to be used with personal
music players shall comply with the requirements of this
sub-clause.
The requirements in this sub-clause are valid for music or
video mode only.
The requirements do not apply:
while the personal music player is connected to
an
external amplifier; or
while the headphones or earphones are not used.
NOTE 2 An external amplifier is an amplifier which is not
part of the personal music player or the listening device,
but which is
intended to play the music as a standalone music player.
The requirements do not apply to:
hearing aid equipment and professional
equipment;
NOTE 3 Professional equipment is equipment sold
through special sales channels. All products sold
through normal
electronics stores are considered not to be professional
equipment.
analogue personal music players (personal music
players without any kind of digital
processing of the sound signal) that are brought
to the market before the end of 2015.
NOTE 4 This exemption has been allowed because this
technology is falling out of use and it is expected that
within a few years it will no longer exist. This exemption
will not be extended to other technologies.
For equipment which is clearly designed or intended for
use by young children, the limits of
EN 71-1 apply.
Page 27 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
Result - Remark
Cont.
≤ 85 dBA
Zx.2 Equipment requirements
No safety provision is required for equipment that
complies with the following:
equipment provided as a package (personal music player
with its listening device), where
the acoustic output LAeq,T is ≤ 85 dBA
measured while playing the fixed “programme
simulation noise” as described in EN 50332-1;
and
a personal music player provided with an analogue
electrical output socket for a listening
device, where the electrical output is ≤ 27 mV
measured as described in EN 50332-2, while
playing the fixed “programme simulation noise”
as
described in EN 50332-1.
NOTE 1 Wherever the term acoustic output is used in
this clause, the 30 s A-weighted equivalent sound
pressure level LAeq,T is
meant. See also Zx.5 and Annex Zx.
Verdict
N/A
All other equipment shall:
a) protect the user from unintentional acoustic
outputs exceeding those mentioned above; and
b) have a standard acoustic output level not
exceeding those mentioned above, and
automatically return to an output level not
exceeding those mentioned above when the
power is switched off; and
c) provide a means to actively inform the user of the
ncreased sound pressure when the equipment is
operated with an acoustic output exceeding
those mentioned above. Any means used shall
be acknowledged by the user before activating a
mode of operation which allows for an acoustic
output exceeding those mentioned above. The
acknowledgement does not need to be repeated
more than once every 20 h of cumulative
listening time; and
NOTE 2 Examples of means include visual or audible
signals. Action from the user is always required.
NOTE 3 The 20 h listening time is the accumulative
listening time, independent how often and how long the
personal music
player has been switched off.
d) have a warning as specified in Zx.3; and
e) not exceed the following:
Cont.
1) equipment provided as a package (player with
Its listening device), the acoustic output shall be
≤ 100 dBA measured while playing the fixed
“programme simulation noise” described in EN
50332-1; and
2) a personal music player provided with an
analogue electrical output socket for a listening
device, the electrical output shall be ≤ 150 mV
measured as described in EN 50332-2, while
playing the fixed “programme simulation noise”
described in EN 50332-1.
Page 28 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
For music where the average sound pressure (long
term LAeq,T) measured over the duration of the
song is lower than the average produced by the
programme simulation noise, the warning does not
need to be given as long as the average sound
pressure of the song is below the basic limit of 85
dBA. In this case T becomes the duration of the
song.
Result - Remark
Verdict
N/A
NOTE 4 Classical music typically has an average
sound pressure (long term LAeq,T) which is much
lower than the average
programme simulation noise. Therefore, if the
player is capable to analyse the song and compare
it with the programme
simulation noise, the warning does not need to be
given as long as the average sound pressure of the
song is below the basic
limit of 85 dBA.
For example, if the player is set with the
programme simulation noise to 85 dBA, but the
average music level of the song is only
65 dBA, there is no need to give a warning or ask
an acknowledgement as long as the average sound
level of the song is not above the basic limit of 85
dBA.
Page 29 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
Result - Remark
Zx.3 Warning
The warning shall be placed on the equipment, or
on the packaging, or in the instruction manual and
shall consist of the following:
the symbol of Figure 1 with a minimum height of
5 mm; and
the following wording, or similar:
The marking be on the
packaging.
Verdict
N/A
“To prevent possible hearing damage, do not listen
at high volume levels for long periods.”
Figure 1 – Warning label (IEC 60417-6044)
Cont.
Alternatively, the entire warning may be given
through the equipment display during use,
when the user is asked to acknowledge activation
of the higher level.
Zx.4 Requirements for listening devices (headphones and earphones)
Zx.4.1 Wired listening devices with analogue input
With 94 dBA sound pressure output LAeq,T, the
input voltage of the fixed “programme simulation
noise” described in EN 50332-2 shall be ≥ 75 mV.
N/A
N/A
This requirement is applicable in any mode where
the headphones can operate (active or
passive), including any available setting (for
example built-in volume level control).
NOTE The values of 94 dBA – 75 mV correspond
with 85dBA – 27 mV and 100 dBA – 150 mV.
Page 30 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
Result - Remark
Zx.4.2 Wired listening devices with digital input
No earphone to sell with the
EUT.
Verdict
N/A
With any playing device playing the fixed
“programme simulation noise” described in
EN 50332-1 (and respecting the digital interface
standards, where a digital interface standard
exists that specifies the equivalent acoustic level),
the acoustic output LAeq,T of the listening device
shall be ≤ 100 dBA.
.
This requirement is applicable in any mode where
the headphones can operate, including any
available setting (for example built-in volume level
control, additional sound feature like
equalization, etc.).
NOTE An example of a wired listening device with
digital input is a USB headphone.
Zx.4.3 Wireless listening devices
In wireless mode:
with any playing and transmitting device playing
the fixed programme simulation noise
described
in EN 50332-1; and
respecting the wireless transmission standards,
where an air interface standard exists that
specifies the equivalent acoustic level; and
with volume and sound settings in the listening
device (for example built-in volume level
control,
additional sound feature like
equalization, etc.)
set to the combination of
positions that maximize
the measured
acoustic output for the above- mentioned
programme simulation noise, the
acoustic
output LAeq,T of the listening device shall
be ≤
100 dBA.
N/A
NOTE An example of a wireless listening device is
a Bluetooth headphone.
Zx.5 Measurement methods
Measurements shall be made in accordance with
EN 50332-1 or EN 50332-2 as applicable.
Unless stated otherwise, the time interval T shall be
30 s.
N/A
NOTE Test method for wireless equipment
provided without listening device should be defined.
Page 31 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
6.1
Requirement + Test
Replace the entire subclause in EN 60065:2002
and EN 60065:2002/A1:2006 by:
(A11:2008) Ionizing radiation
Apparatus including a potential source of ionizing
radiation shall be so constructed that personal
protection against ionizing radiation is provided
under normal operating conditions and under fault
conditions.
Compliance is checked by measurement under the
following conditions:
In addition to the normal operating conditions, all
controls adjustable from the outside BY HAND, by
any object such as a tool or a coin, and those
internal adjustments or pre-sets which are not
locked in a reliable manner, are adjusted so as to
give maximum radiation whilst maintaining an
intelligible picture for 1 h, at the end of which the
measurement is made.
NOTE 1 Soldered joints and paint lockings are
examples of adequate locking.
The dose-rate is determined by means of a
radiation monitor with an effective area of 10 cm²,
at any point 10 cm from the outer surface of the
apparatus.
Moreover, the measurement shall be made under
fault conditions causing an increase of the highvoltage, provided an intelligible picture is
maintained for 1 h, at the end of which the
measurement is made.
The dose-rate shall not exceed 1μSv/h (0,1 mR/h)
taking account of the background level.
NOTE 2 These values appear in Directive
96/29/Euratom of 13th May 1996.
A picture is considered to be intelligible if the
following conditions are met:
- a scanning amplitude of at least 70 % of the
usable screen width;
- a minimum luminance of 50 cd/m² with locked
blank raster provided by a test generator;
- a horizontal resolution corresponding to at least
1,5 MHz in the centre, with a similar vertical
degradation;
- not more than one flashover per 5 min.
Result - Remark
Verdict
N/A
Page 32 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
Result - Remark
Z1
Add the following new clause after Clause 20:
(A11:2008) Z1 Resistance to candle flame ignition
A television set shall be so designed that the
likelihood of ignition and the spread of fire caused
by a candle flame is reduced.
NOTE 1 An apparatus with a viewing screen is not
regarded to be a television set if it is declared not to
be so by the manufacturer.
This requirement does not apply to the display
screen of rear projection TV’s.
NOTE 2 This exemption has been allowed because
this technology is falling out of use and it is
expected that within a few years it will no longer
exist. This exemption will not be extended to other
technologies.
NOTE 3 The frame around the screen is not
exempted from the requirements.
Wood and WOOD-BASED MATERIAL with a
thickness of at least 6 mm is considered to fulfil the
V-1 requirement when applying CLC/TS 62441.
Compliance is checked according to CLC/TS
62441.
NOTE 4 The term vertical, as used in the first dash
of clause 5.2 of CLC/TS 62441, does not mean a
perfectly vertical position. It should be interpreted
as any surface that can be touched by the flame of
a candle of 150 mm height and 20mm diameter
while the candle is still touching the supporting
surface. A typical candle used in the home is
assumed to be 20 mm diameter.
NOTE 5 It is expected that CLC/TS 62441 will in
the future be replaced by a standard, at which time
that standard will become applicable, subject to a
vote by National Committees at the time.
General
13.3.1 Delete note 4.
14
Delete note 4 and note 5.
15.1.1 Delete notes 1 and 2.
15.2 Delete note 2.
16.1 Delete note 1.
16.2 Delete the note.
20
Delete note 2.
Annex B
Replace note 1 by: In the CENELEC countries listed in IEC 62151,
special national conditions apply.
Annex G
Delete the note.
Annex J.2
Delete the notes of Table J.1.
Annex N
Add after the introduction: For ROUTINE TEST reference is made to
EN 50333. (Replaced by EN 50514)
General
In IEC 60065:2001/A2
(A2:2010) Delete all the “country” notes according to the following list:
5.3
Note
Verdict
N/A
N/A
N/A
Page 33 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
Result - Remark
5.4.1 Note
20
Note
For special national conditions, see Annex ZB.
Bibliograph Additional EN standards.
y
Verdict
N/A
ZA
ANNEX ZA: OTHER INTERNATIONAL PUBLICATIONS QUOTED IN THIS
STANDARD WITH THE REFERENCES OF THE RELEVANT EURPEAN
PUBLICATIONS
N/A
ZB
2.6.1
ANNEX ZB TO EN 60065, SPECIAL NATIONAL CONDITIONS (EN)
DK: The following is added:
Certain types of CLASS I apparatus, see 15.1.1,
may be provided with a plug not establishing
earthing continuity when inserted in Danish socketoutlets
Justification: Heavy Current Regulations, Section
107.
Denmark
Add to the end of the subclause
Due to many existing installations where the
socket-outlets can be protected with
fuses with higher rating than the rating of the
socket-outlets the protection for
pluggable equipment type A shall be an integral
part of the equipment.
Justification:
In Denmark an existing 13 A socket outlet can be
protected by a 20 A fuse.
N/A
N/A
3.Z1
(A2:2010)
N/A
Page 34 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
5.3
(A2:2010)
Finland, Norway and Sweden
To the end of the subclause the following is added:
CLASS I apparatus which is intended for
connection to the building installation wiring
via a plug or an appliance coupler, or both and in
addition is intended for connection
to other apparatus or a network shall, if safety
relies on connection to protective earth
or if surge suppressors are connected between the
network TERMINALS and
ACCESSIBLE parts, have a marking stating that
the apparatus must be connected to an
earthed MAINS socket-outlet.
The marking text in the applicable countries shall
be as follows:
In Finland: "Laite on liitettävä suojakoskettimilla
varustettuun pistorasiaan"
In Norway: “Apparatet må tilkoples jordet
stikkontakt”
In Sweden: “Apparaten skall anslutas till jordat
uttag”
5.4
Finland, Norway and Sweden
(A11:2008) To the end of 5.4 the following is added:
CLASS I apparatus which is intended for
connection to the building installation wiring via a
plug or an appliance coupler, or both and in
addition is intended for connection to other
apparatus or a network shall, if safety relies on
connection to protective earth or if surge
suppressors are connected between the network
TERMINALS and ACCESSIBLE parts, have a
marking stating that the apparatus must be
connected to an MAINS socket-outlet with
protective earth.
The marking text in the applicable countries shall
be as follows:
In Finland: “Laite on liitettävä
suojamaadoituskoskettimilla varustettuun
pistorasiaan”
In Norway: “Apparatet må tilkoples jordet
stikkontakt”
In Sweden: “Apparaten skall anslutas till jordat
uttag”
Result - Remark
Verdict
N/A
N/A
Page 35 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
5.4.1
Norway and Sweden
(A11:2008)
Result - Remark
Verdict
N/A
To the end of 5.4.1 (after the compliance statement) the
following is added:
The screen of the cable distribution system is normally
not earthed at the entrance of the building and there is
normally no equipotential bonding system within the
building. Therefore the protective earthing of the building
installation need to be isolated from the screen of a cable
distribution system.
It is however accepted to provide the insulation external
to the equipment by an adapter or an interconnection
cable with galvanic isolator, which may be provided by
e.g. a retailer.
The user manual shall then have the following or similar
information in Norwegian and Swedish language
respectively, depending on in what country the
equipment is intended to be used in:
“Equipment connected to the protective earthing of the
building installation through the mains connection or
through other equipment with a connection to protective
earthing – and to a cable distribution system using
coaxial cable, may in some circumstances create a fire
hazard. Connection to a cable distribution system has
therefore to be provided through a device providing
electrical isolation below a certain frequency range
(galvanic isolator, see EN 60728-11)”
NOTE In Norway, due to regulation for installations of
cable distribution systems, and in Sweden, a galvanic
isolator shall provide electrical insulation below 5 MHz.
The insulation shall withstand a dielectric strength of 1,5
kV r.m.s., 50 Hz or 60 Hz, for 1 min.
Translation to Norwegian (the Swedish text will also be
accepted in Norway):
“Utstyr som er koplet til beskyttelsesjord via nettplugg
og/eller via annet jordtilkoplet utstyr – og er tilkoplet et
kabel-TV nett, kan forårsake brannfare. For å unngå
dette skal det ved tilkopling av utstyret til kabel-TV nettet
installeres en galvanisk isolator mellom utstyret og kabelTV nettet.”
Translation to Swedish:
”Utrustning som är kopplad till skyddsjord via jordat
vägguttag och/eller via annan utrustning och samtidigt är
kopplad till kabel-TV nät kan i vissa fall medföra risk för
brand.
Főr att undvika detta skall vid anslutning av utrustningen
till kabel-TV nät galvanisk isolator finnas mellan
utrustningen och kabel-TV nätet.”
Page 36 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
13.3.1
Requirement + Test
NO: To the second paragraph the following is
added:
In Norway, due to the IT power distribution system
used, the a.c. MAINS supply voltage is considered
to be equal to the line-to-line voltage, and will
remain 230 V in case of a single earth fault.
Justification: Based on a use in Norway of an IT
power distribution system where the neutral is not
provided.
15.1.1
Denmark
(A11:2008) The text of the Danish SNC in EN 60065:2002 has
been modified as follows:
To the first paragraph the following is added:
In Denmark, supply cords of single-phase
appliances having a rated current not exceeding 13
A shall be provided with a plug according to the
Heavy Current Regulations Section 107-2-D1.
Appliances of CLASS I provided with socket-outlets
with earth contact or which are intended to be used
in locations where protection against indirect
contact is required according to the wiring rules
shall be provided with a plug in accordance with the
Heavy Current Regulations, Section 107-2-D1
standard sheet DK 2-1a.
To the second paragraph the following is added:
Socket outlets intended for providing power to
CLASS II apparatus with a rated current of 2,5 A
shall be in accordance with the Heavy Current
Regulation, Section 107-2-D1 standard sheet DKA
1-4a.
Other current ratings socket outlets shall be in
compliance with the Heavy Current Regulation,
Section 107-2-D1 standard sheet DKA 1-3a or DKA
1-3b.
To the third paragraph the following is added:
Mains socket-outlets with earthing contact shall be
in compliance with the Heavy Current Regulation,
Section 107-2-D1 standard sheet DK 1-3a, DK 1-5a
or DK 1-7a.
Justification: Heavy Current Regulations, Section
107-2-D1
15.1.1
IE: Apparatus which is fitted with a flexible cable or
cord shall be provided with a 13 A plug in
accordance with Statutory Instrument 525:97, “13 A
Plugs and Conversion Adapters for Domestic Use
Regulations:1997.
Justification: SI 525: 1997
Result - Remark
Verdict
N/A
N/A
N/A
Page 37 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
15.1.1
NO: Mains socket-outlets mounted on CLASS II
apparatus shall comply with the specifications
given in CEE Publ. 7 as far as a applicable, with
the following amendments:
§ 8 Dimensions
a 2.5 A 250 V two-pole socket-outlets for electronic
apparatus shall comply with the enclosed Standard
Sheet I.
15.1.1
§ 24 Mechanical strength
A 2,5 A 250 V socket-outlets for CLASS II
electronic apparatus are tested as specified in
12.1.3 of EN 60065. Also the protecting rim shall be
tested
Justification: Act of 24 May 1929 relating to
supervision of electrical installation (TEA 1929/FEL
1998).
UK: Apparatus which is fitted with a flexible cable
or cord and is designed to be connected to a mains
socket conforming to BS 1363 by means of that
flexible cable or cord and plug shall be fitted with
a ”standard plug” in accordance with Statutory
Instrument 1768: 1994: The Plugs and Sockets etc.
(Safety) Regulations 1994, unless exempted by
those Regulations.
NOTE ”Standard plug” is defined in SI 1768:1994
and essentially means an approved plug
conforming to BS 1363 or an approved conversion
plug.
Justification: SI 1768: 1994
Result - Remark
Verdict
N/A
N/A
Page 38 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
EN 60065
Clause
Requirement + Test
J.2
NO: After Table J.1 the following is added:
In Norway, due to the IT power distribution system
used, the a.c. MAINS supply voltage is considered
to be equal to the line-to-line voltage, and will
remain 230 V in case of a single earth fault.
Justification: Based on a use in Norway of an IT
power distribution system where the neutral is not
provided.
N/A
ZC
5
ANNEX ZC: A-DEVIATIONS
DE: additional markings required in German
language:
cathode ray tubes with an accelerating voltage
between 20 kV and 30 kV (marking on the tube)
TV receivers whose picture tube has an
accelerating voltage between 20 kV and 30 kV
TV receivers whose picture tube has an
accelerating voltage greater than 30 kV
TV receivers whose picture tube has an
accelerating voltage less than 20 kV
IT: additional markings on the outside of the TV
receiver in Italian language
IT: user instructions in Italian language including a
conformity declaration
IT: certification number on the back cover
DE: The following requirement applies:
For the operation of any cathode ray tube
intended for the display of visual images operating
at an acceleration voltage exceeding 40 kV,
authorization is required, or application of type
approval (Bauartzulassung) and marking.
Justification: German ministerial decree against
ionizing radiation (Röntgenverordnung), in force
since 2002-07-01, implementing the European
Directive 96/29/EURATOM.
NOTE Contact address:
Physikalisch-Technische Bundesanstalt,
Bundesallee 100, D-38116 Braunschweig, Tel.:
Int+49-531-592-6320, Internet: http://www.ptb.de
Sweden: switches containing mercury such as
thermostats, relays and level controllers are no
allowed
N/A
N/A
5.1
6.1
14
Result - Remark
Verdict
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Page 39 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
Table 7.1
TABLE: temperature rise measurements
P
Voltage
Frequency
Ampere
Watts
18V DC
--
1.24A
22.3W
Note
Normal operation
Power consumption in the OFF/Stand-by
--
--
Position of the functional switch (W) ......................:
--
--
Operating conditions
Loudspeaker impedance (Ω) ................. --
—
Several loudspeaker systems
--
--
Monitored point:
dT (K)
Limit dT (K)
Normal operation
Speaker
13.4
Ref
Internal wire
12.1
45
Enclosure inside near speaker
8.6
45
Enclosure outside near speaker
7.5
45
Remark:35°C ambient considered
7.2
Temperature T of part
10.3
T - normal conditions (℃)
T - fault conditions (℃)
--
--
--
--
--
--
--
--
Input to plastic enclosure
(°C)
N/A
R (MΩ)
Required R (MΩ)
--
--
TABLE: electric strength measurements
Test voltage applied between:
Input to enclosure
14.10
Min T softening
TABLE: insulation resistance measurements
Insulation resistance R between:
10.3
N/A
TABLE: softening temperature of thermoplastics
TABLE: Batteries
P
Test voltage (V)
Breakdown
707VDC
No
N/A
Manufacturer ............................................... :
Type / model................................................ :
Voltage......................................................... :
Capacity....................................................... :
Tested and Certified by (incl. Ref. No.) ....... :
Circuit protection diagram............................ :
Page 40 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
MARKINGS AND INSTRUCTIONS (5.4.1, 14.10)
Location of replaceable battery
Language(s):
Close to the battery
In the servicing instructions
In the operating instructions
14.10
TABLE: Batteries
N/A
The tests of 14.10 are applicable only when
appropriate battery data is not available
Appropriate battery data is available.
Is it possible to install the battery in a reverse
polarity position?
No
Temperature
Measured temperature: Ref. 11.2
Non-rechargeable batteries
Discharging
Meas.
current
Manuf.
spec.
--
--
Max
-current
during fault
conditions
--
Max
current
during
normal
conditions
Unintentional
charging
Rechargeable batteries
Charging
Discharging
Reversed
charging
Meas.
current
Manuf.
spec.
Meas.
current
Manuf.
spec.
Meas.
current
Manuf.
spec.
--
--
--
--
--
1)
1)
--
--
--
--
--
1)
1)
supplementary information:
1)--Refer to table 11.2 for test results.
2) Battery polarity can’t be reversed according to the design of enclosure and connector.
Test results:
Appropriate battery data is available.
Verdict
- Chemical leaks
No chemical leaks affecting required
insulation.
N/A
- Explosion of the battery
No explosion
N/A
- Emission of flame or expulsion of molten metal
No emission of flame or expulsion of
molten metal.
N/A
- Electric strength test of equipment after completion
of tests
Class III equipment
N/A
supplementary information:
Page 41 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
11.2
\
No.
TABLE: summary of fault condition tests
P
Voltage (V) 0,9 or 1,1 times rated voltage .............. :
18.0V
—
Frequency (Hz)........................................................ :
DC
—
Ambient temperature (°C) ...................................... :
See below
—
Componen Supply volt
tage (V)
Fault
Test
time
dT (K) /
Component
Other results
(include description and test duration)
1
C1
18.0Vdc
S-C
10 mins
--
Amplifier shut down, no components
damaged, no hazards
2
D3
18.0Vdc
S-C
10 mins
--
Amplifier shut down, no components
damaged, no hazards
3
U1(1-4)
18.0Vdc
S-C
10 mins
--
Amplifier shut down, no components
damaged, no hazards
4
Speaker
18.0Vdc
S-C
2h25mi
ns
--
No components damaged, no hazards
13.2
N/A
TABLES: clearances and creepage distances
Location
RMS Voltage (V)
Peak Voltage (V)
--
--
-14
Comments
--
TABLE: list of critical components and materials
P
Object/part No.
Manufacturer/
trademark
Type/model
Technical data
Standard
(Edition /
year)
SPEAK
--
--
8 OHM, 10W
EN 60065
Tested with
appliance
Enclosure
--
--
Wooden, 10.38mm
--
--
Heat shrinkable
tube
GUANGZHOU
KAIHENG
NEW
MATERIAL CO
LTD
K-102
600V, 125℃,VW-1
UL 224
UL
PCB
Various
Various
130℃ V-1
UL 796
UL
SWITCHING
ADAPTER
SHENZHEN
FUJIA
APPLIANCE
CO LTD
FJSW1802000D
Input:100-240V~
50/60Hz 1.5A MAX
UL 60065
UL
IEC 60065
GS
Output:18V
2A
Mark(s) of
conformity1)
1
) An asterisk indicates a mark which assures the agreed level of surveillance
Supplementary information:
Page 42 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
ANNEX AA: Equipment list
Code
Name
Model/Type
S/N
Calibrated
date
Next
Calibration
Date
Manufacture
TC-001
Digital Multimeter
34401A
MY47043456
2014.02.19
2015.02.18
agilent
TC-004
Push/pull gauge
NK-500
2Q10060932
2014.02.19
2015.02.18
TC-005
Electronic weight
DSI-861
198692
2014.02.19
2015.02.18
shangdeli
TC-006
Insulation
resistance tester
CS2676CX
1107032-009
2014.02.19
2015.02.18
changshen
TC-007
Earthing
resistance tester
YD2668-4B
4B-2307
2014.02.19
2015.02.18
Yangzi
TC-008
HI-pot/Insulation
tester
CS2672C
1108006-002
2014.02.19
2015.02.18
changshen
2014.02.19
2015.02.18
SAKO
TC-010
AC Voltage
Regulator
TDGC2J
TC-013
AC power source
HPA-3110
3513
2014.02.19
2015.02.18
Henqiang
TC-014
Temperature/Hum
idity chamber
SDJ-80L
SDJ-80J
2014.02.19
2015.02.18
Shenzhen
hongjian
TC-015
Electric oven
HK45AS
F11011008
2014.02.19
2015.02.18
Guangzhou
KENTON
TC-017
AC digital power
meter
PF9901
YG100731N110
70075
2014.02.19
2015.02.18
Yuanfang
TC-022
Leakage current
tester
228
10-866030
2014.02.19
2015.02.18
simpson
TC-023
Oscilloscope
TDS1012C-SC
C013300
2014.02.20
2015.02.19
tektronix
TC-024
Tape measure
DK-2041
2014.02.22
2015.02.21
Proskit
TC-025
Stop watch
TA-228
2014.02.20
2015.02.19
KTJ
2014.02.23
2015.02.22
Agilent
2014.02.20
2015.02.19
ViCTOR
TC-026
TC-027
Data
acquisition/switch
unit
Temperature/humi
dity meter
34970A
MY44057668
VC230
TC-028
Torque drive
3RTD
435850B
2013.05.14
2014.05.13
TOHNICHI
TC-033
Test finger
ZLT-I02
I021203
2014.02.22
2015.02.21
Guangzhou
zhilitong
TC-034
Test pin
ZLT-I09
I091201
2014.02.22
2015.02.21
Guangzhou
zhilitong
TC-038
Test apparatus of
the mains plug
ZLT-LJ2
LJ011202
2014.02.19
2015.02.18
Guangzhou
zhilitong
TC-039
Ball pressure
apparatus
ZLT-QY1
Q011202
2014.02.20
2015.02.19
Guangzhou
zhilitong
Page 43 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
TC-040
Impact hammer
ZLT-CJ1
LJ011206
2014.02.20
2015.02.19
Guangzhou
zhilitong
TC-041
Impact hammer
ZLT-CJ1
LJ011205
2014.02.20
2015.02.19
Guangzhou
zhilitong
TC-042
Caliper rule
CD-6"CSX
500-196-20
2013.07.04
2014.07.03
MITUTOYO
TC-044
Glow wire tester
ZRS-2
12121304
2013.12.16
2014.12.15
Guangzhou
Xinna
TC-045
Needle flame
tester
ZY-2
12121311
2013.12.16
2014.12.15
Guangzhou
Xinna
TC-107
“Van der Hoofden”
test head
EMF827
R21SW
2013.12.16
2014.12.15
Shenzhen HLKS
TC-107-a
Measurement
receiver
EMF827-a
R21SW
2013.12.16
2014.12.15
Shenzhen HLKS
Page 44 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
ANNEX BB: Photo-documentation
Photo 1
[
] front
[
] rear
[
] right side
[
] left side
[√ ] top
[
] bottom
[
] internal
Photo 2
[
] front
[
] rear
[
] right side
[
] left side
[
] top
[√] bottom
[
] internal
Page 45 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
Photo 3
[
] front
[
] rear
[
] right side
[
] left side
[
] top
[√] bottom
[
] internal
Photo 4
[
] front
[
] rear
[
] right side
[
] left side
[
] top
[
] bottom
[√] internal
Page 46 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Report No.: TCT140428011S1-1
Photo 5
[
] front
[
] rear
[
] right side
[
] left side
[
] top
[
] bottom
[√] internal
Photo 6
[
] front
[
] rear
[
] right side
[
] left side
[
] top
[
] bottom
[√] internal
***End of Test Report***
Page 47 of 47
Hotline: 400-6611-140 Tel: 86-755- 27673339 Fax: 86-755-27673332 http://www.tct-lab.com
.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement