LawMate WCH-250X Operation Manuals
Add to my manuals1 Pages
LawMate WCH-250X is a wireless camera hunter that can detect and display wireless A/V signals on its screen. It has a scanning mode that automatically scans for signals and displays them for a few seconds, or you can manually scan by scrolling up or down with the SETUP key. The device has a built-in battery that can be charged using the supplied power adapter, and it also has a low battery alert to let you know when it's time to charge. The WCH-250X can be used in various situations, such as security, surveillance, and law enforcement.
advertisement
LCM Operation Interface
■
Enter setting:
Slide the POWER key on side of the unit to turn on the device, press and hold the
SETUP key for 3 seconds then release it. The icon will be blinking on the LCM (the
smaller screen), scroll the SETUP key upward or downward to change setting.
■
Change setting:
Press the SETUP key once to confirm change and to move on next setting.
■
Exit setting:
Press and hold the SETUP key again for 3 seconds.The device will return to scanning mode.
Scanning
Mode
Signal Dwell
Time
Receiver
Sensitivity
Audio & Vibration
Alert Setting
00
1080
EX
EXT. AV input mode
30
30 Sec. interval mode a 60
60 sec. interval mode
00
Standard scanning mode
30
1080
30
8 seconds
30 4
4 seconds
30 2
2 seconds
30
1080
UH
30 UH
UH (Ultra High
/ -75dBm)
30 2
1080
30 2 B
B
Alert on/Vibrate Off
30
H (High/-60dBm)
30 MH
MH (Medium High
/-50dBm)
30 M
M (Medium/-40dBm)
30 ML
ML (Medium Low
/-30 dBm)
60 L
30 MH B
Alert on/Vibrate On
30 MH
Alert Off/Vibrate Off
30 M
Alert Off/Vibrate On
(3)
L (Low/-20dBm)
Names and Parts
2.4 & 5.8GHz ant. mount 1.2GHz ant. mount
SETUP key
67.00 mm
LCM screen LCD screen
(1)
Signal In/Out socket
21.20 mm
DC 5V In
Power Switch
WCH-250X
Wireless Camera Hunter Operation
Manual
00
Law Enforcement Products Manufacturer
LawMate
V1.0
■
Installing the battery
Remove battery cover on back of the unit. Slide the supplied battery at about 15 degree angle to the battery compartment. Please be aware of +/- direction.
■
Charging the battery:
Connect the supplied power adaptor to an AC wall outlet and attached the other end
of the cord to the DC 5V In socket.
■
Power indication:
When charging the battery, a red color LED light will illuminate. Once the battery is
fully charged, the LED light will turn off. (The charging time is approximately 3 ~ 4
hours depending on the battery remaining power.) Please charge the battery for 8
hours on the first-time use.
■
Antenna connector
2 1
Plug antenna 1 to port 1 and antenna 2 to port 2. You can find the indication printed on the antennas as well as on the ports. Turn the antenna’s base clockwise until it locks into place.
■
Power switch:
The power switch is on the side of the device. When the unit is turned on, it starts
scanning the signal automatically. Make sure the antenna is screwed tightly to its
allocated position to avoid poor reception.
■
Frequency scanning:
Whenever a wireless A/V signal is detected, the image will be displayed on the
screen and stays for few seconds. The length of time depends on your setting. You
have the option to lock the channel by scroll upward or downward the SETUP key on
side of the device to lock the channel or else it will pass on and continue scanning.
■
Manual scanning:
Scroll upward or downward the SETUP key to scan manually.
■
Low battery alert:
When the battery gets low, the battery icon will blink. Charge your battery immediately.
■
External video input:
To connect external video to the device, change the setting to EX mode. Make sure
the connector is plugged properly to the Signal In/Out socket on side of the device,
otherwise it will result non-signal input.
(2)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project