MyBinding MBM BookletMaker Jr. User manual

MyBinding MBM BookletMaker Jr. User manual
Operation Manual
FOR
BOOKLETMAKER Jr.
1-800-223-2508
www.mbmcorp.com
Keep this manual sot that it can be retrieved whenever needed
CAUTION
When the machine is running, never put your
hands near or under the rollers.
Do not remove the bottom lid, front and rear
covers from the machine. The inside of the
machine contains high voltage parts or
hazardous moving parts, which may cause
electric shock or personal injury.
A socket-outlet shall be installed near the
equipment and shall be easily accessible.
Warning
Warning:
hazardous moving parts keep hands
and other body parts away.
Warn:
The surface of the
, motor is hot.
Be careful, Don t touch
Caution
Caution:
For continued protection
against risk of fire, replace only with
the same type and rating of fuse.
No.
Description
Qty
1
Warning Label 1
1
2
Cover Label
2
3
Brand Label
1
4
Model Label
1
5
Fuse Label
1
6
Caution Label
1
7
Warning Label 2
1
8
Warning Label 3
1
1
2
3
4
5
13
12
6 7
8 9 10
11
Main Operating Parts
(1) Safety Cover
(8) Paper Guide
(2) Back Cover
(3) Stapling Handle
(4) Side Guide (B)
(5) Sub Holding Shaft
(9) Table
(10) Side Guide (A)
(11) Front Cover
(12) On/Off Switch
(13) Rubber Feet
(7) Stapling Head
1
Wa rning ha za rd o us m o ving p a rts ke e p
ha nd s a nd o the r b o d y p a rts a wa y
2
Do not remove the cover
Doing so may result in personal injury
3
4
M O D EL
BO O K LETM A K ER Jr.
N . Ch a r l e st o n , SC 2 9 4 1 8
800- 223- 2508
5
6
CA UTION:
7
Warn:
The surface of the
, motor is hot.
Be careful, Don t touch
8
Warn:
The surface of the
, motor is hot.
Be careful, Don t touch
Operation Procedures
1. B ef o r e Op er at i n g
1.1 Fit stapling handle:
First insert the end of the stapling
handle at the main holding shaft then
press in the sub-holding shaft.
1.2 Load Staples
1.3 Connect the power cable
2.1 Switch on the machine
2.2 Choose the correct staple position according to the sheet size.
2.3 Set the paper guides; place the sheets under the rollers and align
the sheets to side guide (A).
2.4 Set the paper guides to hold the sheets in position.
2.5 Press down the stapling handle to complete the stapling.
2.6 Lift up the stapling handle and firmly press down to the other side
and hold. The stapled sheets will be fed up through the fold rollers
to complete the booklet.
2.7 Repeat steps 2.3-2.6 for further booklets.
2.8 Switch off the machines after finishing.
3. Si d e St ap l i n g
3.1 Choose and fix the staple position according to the sheet size.
3.2 Place the sheets under the rollers.
3.3 Depending on the stapling position, align the sheets to side
guide (A)or side guide (B)
3.4 Set the side distance and hold the sheets.
3.5 Press down the stapling handle for stapling.
3.6 Repeat steps 3.2-3.5 for further side stapling.
4. Rep ai r & Mai n t en an c e
4.1 Always clean up machine after used.
Sp ec i f i c at i o n s
Paper size
Min.197mmx273mm (7.8 x 10.8 )
Max. 297mmx420mm ( 11.7 x 16.5 )
Max. Stapling Amount 10 sheets of 70gsm Bond paper*
( 20 lbs. paper)
Max. Folding Amount
10 sheets of 70gsm Bond paper *
[40 pages booklet] (20 lbs. paper)
Power source
AC 110V 0.8A 60Hz
Watt
40W
Dimensions
500mmx235mmx395mm
(19.7 x 9.3 x 15.6 )
Weight
15Kg
( 33lbs.)
* This may vary depending upon paper quality
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement