Operation Manual
FOR
BOOKLETMAKER Jr.
1-800-223-2508 www.mbmcorp.com
Keep this manual sot that it can be retrieved whenever needed
CAUTION
When the machine is running, never put your hands near or under the rollers.
Do not remove the bottom lid, front and rear covers from the machine. The inside of the machine contains high voltage parts or hazardous moving parts, which may cause electric shock or personal injury.
A socket-outlet shall be installed near the equipment and shall be easily accessible.
Warning
Warning: hazardous moving parts keep hands and other body parts away.
Warn:
The surface of the motor is hot.
Caution
Caution:
For continued protection against risk of fire, replace only with the same type and rating of fuse.
No.
1
2
3
4
7
8
5
6
Description
Warning Label 1
Cover Label
Brand
Label
Model Label
Fuse Label
Caution Label
Warning Label 2
Warning Label 3
1
1
1
1
1
2
1
Qty
1
1 2
3 4 5
6 7
8 9 10
Main Operating Parts
13 12 11
(1) Safety Cover
(2) Back Cover
(3) Stapling Handle
(4) Side Guide (B)
(5) Sub Holding Shaft
(7) Stapling Head
(8) Paper Guide
(9) Table
(10) Side Guide (A)
(11) Front Cover
(12) On/Off Switch
(13) Rubber Feet
1
Wa rning ha za rd ous m o ving p a rts keep ha nd s a nd other b od y p a rts a wa y
2
Do not remove the cover
Doing so may result in personal injury
3
4
N . Ch a r l e st o n , SC 2 9 4 1 8
M O D EL
BO O K LETM A K ER Jr.
8 0 0 - 2 2 3 - 2 5 0 8
5
CA UTION:
7
Warn:
8
Warn:
,
6
Operation Procedures
1. B efo r e Oper at i ng
1.1 Fit stapling handle: First insert the end of the stapling
handle at the main holding shaft then
press in the sub-holding shaft.
1.2 Load Staples
1.3 Connect the power cable
2.1 Switch on the machine
2.2 Choose the correct staple position according to the sheet size.
2.3 Set the paper guides; place the sheets under the rollers and align
the sheets to side guide (A).
2.4 Set the paper guides to hold the sheets in position.
2.5 Press down the stapling handle to complete the stapling.
2.6 Lift up the stapling handle and firmly press down to the other side
and hold. The stapled sheets will be fed up through the fold rollers
to complete the booklet.
2.7 Repeat steps 2.3-2.6 for further booklets.
2.8 Switch off the machines after finishing.
3. Sid e Stap lin g
3.1 Choose and fix the staple position according to the sheet size.
3.2 Place the sheets under the rollers.
3.3 Depending on the stapling position, align the sheets to side
guide (A)or side guide (B)
3.4 Set the side distance and hold the sheets.
3.5 Press down the stapling handle for stapling.
3.6 Repeat steps 3.2-3.5 for further side stapling.
4. Rep ai r & Main tenanc e
4.1 Always clean up machine after used.
Spec ificat ions
Paper size
Min.197mmx273mm (7.8 x 10.8 )
Max. 297mmx420mm ( 11.7 x 16.5 )
Max. Stapling Amount
10 sheets of 70gsm
(
20
lbs. paper)
Bond paper*
Max. Folding Amount
10 sheets of 70gsm
[40 pages booklet]
Bond paper
*
(20 lbs. paper)
Power source AC 110V 0.8A 60Hz
Watt
40W
Dimensions
Weight
500mmx235mmx395mm
(19.7 x 9.3 x 15.6 )
15Kg
( 33lbs.)
* This may vary depending upon paper quality
