advertisement
Hardware Maintenance Manual
ThinkPad L420, L421, and L520
Note
Before using this information and the product it supports, be sure to read the general information under
Appendix A “Notices” on page 151.
Fourth Edition (August 2011)
© Copyright Lenovo 2011.
LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration
“GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
Contents
About this manual. . . . . . . . . . .
iii
Chapter 1. Safety information . . . . . . 1
General safety . . . . . . . . . . . . . . . .
Electrical safety . . . . . . . . . . . . . . .
Safety inspection guide . . . . . . . . . . . .
Handling devices that are sensitive to electrostatic discharge. . . . . . . . . . . . . . . . . .
Grounding requirements . . . . . . . . . . . .
Safety notices (multilingual translations) . . . . . .
Laser compliance statement (multilingual translations) . . . . . . . . . . . . . . . .
Chapter 2. Important service information . . . . . . . . . . . . . .
25
Strategy for replacing FRUs . . . . . . . . .
Strategy for replacing a hard disk drive . . .
Important notice for replacing a system board . . . . . . . . . . . . . . . .
How to use error message . . . . . . . .
Strategy for replacing FRUs for CTO, CMV, and
GAV . . . . . . . . . . . . . . . . . . .
Product definition . . . . . . . . . . . .
FRU identification for CTO, CMV, and GAV products . . . . . . . . . . . . . . .
Chapter 3. General checkout . . . . .
29
What to do first . . . . . . . . . . . . . .
Checkout guide . . . . . . . . . . . . . .
Diagnostics using PC-Doctor for DOS. . . .
Lenovo ThinkVantage Toolbox . . . . . . .
FRU tests . . . . . . . . . . . . . . .
Power system checkout . . . . . . . . . . .
Checking the ac power adapter . . . . . .
Checking operational charging . . . . . .
Checking the battery pack . . . . . . . .
Checking the backup battery . . . . . . .
Chapter 4. Related service information . . . . . . . . . . . . . .
37
Restoring the factory contents by using Recovery
Disc Set . . . . . . . . . . . . . . . . .
Passwords . . . . . . . . . . . . . . . .
Power-on password . . . . . . . . . . .
Hard-disk password. . . . . . . . . . .
Supervisor password . . . . . . . . . .
How to remove the power-on password . . .
How to remove the hard-disk password . . .
© Copyright Lenovo 2011
Power management . . . . . . . . . . . .
Screen blank mode . . . . . . . . . . .
Sleep (standby) mode . . . . . . . . . .
Hibernation mode . . . . . . . . . . .
Symptom-to-FRU index . . . . . . . . . . .
Numeric error codes . . . . . . . . . .
Error messages . . . . . . . . . . . .
No-beep symptoms . . . . . . . . . . .
LCD-related symptoms . . . . . . . . .
Intermittent problems . . . . . . . . . .
Undetermined problems . . . . . . . . .
Chapter 5. Status indicators . . . . .
47
Chapter 6. Fn key combinations . . .
49
Chapter 7. FRU replacement notices . . . . . . . . . . . . . . . .
53
Screw notices . . . . . . . . . . . . . . .
Retaining serial numbers. . . . . . . . . . .
Restoring the serial number of the system unit . . . . . . . . . . . . . . . . .
Retaining the UUID . . . . . . . . . . .
Reading or writing the ECA information . . .
Chapter 8. Removing and replacing a
FRU . . . . . . . . . . . . . . . . . .
57
1010 Battery pack . . . . . . . . . . . . .
1020 ExpressCard blank bezel and Media Card blank bezel . . . . . . . . . . . . . . . .
1030 Optical drive or travel cover . . . . . . .
1040 Thermal cover. . . . . . . . . . . . .
1050 Hard disk drive or solid state drive assembly . . . . . . . . . . . . . . . . .
1060 DIMM . . . . . . . . . . . . . . . .
1070 Fan assembly . . . . . . . . . . . . .
1080 CPU . . . . . . . . . . . . . . . .
1090 SIM slot cover . . . . . . . . . . . .
1110 Wireless WAN slot cover and PCI Express
Mini Card for wireless WAN. . . . . . . . . .
1110 mSATA solid state drive . . . . . . . . .
1120 Palm rest assembly with cables . . . . . .
1130 PCI Express Mini Card for wireless LAN . .
1140 Backup battery . . . . . . . . . . . .
1150 Bluetooth daughter card . . . . . . . .
1160 Media Card Reader slot board and Media
Card Reader cable assembly . . . . . . . . .
1170 Keyboard . . . . . . . . . . . . . .
i
1180 Keyboard bezel . . . . . . . . . . . .
1190 LCD unit . . . . . . . . . . . . . . .
2010 Top shielding assembly . . . . . . . . .
2020 System board assembly. . . . . . . . .
2030 USB connector board and USB cable assembly . . . . . . . . . . . . . . . . .
2040 DC-in cable and base cover . . . . . . .
2050 LCD front bezel . . . . . . . . . . . .
2060 Speaker assembly . . . . . . . . . . .
2070 Integrated camera . . . . . . . . . . .
2080 Antenna assembly . . . . . . . . . . .
2090 Hinges, LCD panel, LCD cable, and LCD rear cover assembly . . . . . . . . . . . . . .
Chapter 9. Locations . . . . . . . .
109
Front view . . . . . . . . . . . . . . . .
Rear view. . . . . . . . . . . . . . . . .
Bottom view . . . . . . . . . . . . . . .
Chapter 10. Parts list . . . . . . . .
111
Overall . . . . . . . . . . . . . . . . . .
LCD FRUs . . . . . . . . . . . . . . . .
Keyboard . . . . . . . . . . . . . . . . .
Miscellaneous parts . . . . . . . . . . . .
ac power adapters . . . . . . . . . . . . .
Power cords . . . . . . . . . . . . . . .
Recovery discs . . . . . . . . . . . . . .
Windows XP Professional DVDs . . . . . .
Windows XP Professional Generic DVDs. . .
Windows Vista Business (32 bit) DVDs . . .
Windows Vista Home Basic (32 bit) DVDs . .
Windows 7 Home Basic (32 bit) DVDs. . . .
Windows 7 Home Premium (32 bit) DVDs . .
Windows 7 Home Premium (64 bit) DVDs . .
Windows 7 Professional (32 bit) DVDs. . . .
Windows 7 Professional (64 bit) DVDs. . . .
Windows 7 Starter (32 bit) DVDs . . . . . .
Windows 7 Ultimate (32 bit) DVDs . . . . .
Windows 7 Ultimate (64 bit) DVDs . . . . .
Common service tools . . . . . . . . . . .
Appendix A. Notices . . . . . . . . .
151
Electronic emissions notices . . . . . . . . .
Trademarks . . . . . . . . . . . . . . . .
ii
Hardware Maintenance Manual
About this manual
This manual contains service and reference information for the following ThinkPad
®
Notebook products.
ThinkPad L420
Machine Type (MT) 7826, 7827, 7829, 7853, 7854, and 7856
ThinkPad L421
MT 7826, 7827, 7829, 7853, 7854, and 7856
ThinkPad L520
MT 5015, 5016, 5017, 5019, 7859, and 7860
Use this manual along with the advanced diagnostic tests to troubleshoot problems.
Important:
This manual is intended only for trained service technicians who are familiar with ThinkPad products. Use this manual along with the advanced diagnostic tests to troubleshoot problems effectively.
Before servicing a ThinkPad product, be sure to read all the information under Chapter 1 “Safety
information” on page 1 and Chapter 2 “Important service information” on page 25.
© Copyright Lenovo 2011
iii
iv
Hardware Maintenance Manual
Chapter 1. Safety information
This chapter presents following safety information that you need to be familiar with before you service a ThinkPad Notebook.
•
•
•
“Safety inspection guide” on page 3
•
“Handling devices that are sensitive to electrostatic discharge” on page 3
•
“Grounding requirements” on page 4
•
“Safety notices (multilingual translations)” on page 4
•
“Laser compliance statement (multilingual translations)” on page 17
General safety
Follow these rules to ensure general safety:
• Observe good housekeeping in the area of the machines during and after maintenance.
• When lifting any heavy object:
1. Make sure that you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.
4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you think is too heavy for you.
• Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe.
• Before you start the machine, make sure that other service technicians and the customer's personnel are not in a hazardous position.
• Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the machine.
• Keep your toolcase away from walk areas so that other people will not trip over it.
• Do not wear loose clothing that can be trapped in the moving parts of a machine. Make sure that your sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it.
• Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, about 8 centimeters (3 inches) from the end.
• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing.
Attention: Metal objects are good electrical conductors.
• Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using solvents, or working in any other conditions that might be hazardous to your eyes.
• After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that is worn or defective.
• Reinstall all covers correctly before returning the machine to the customer.
• Fan louvers on the machine help to prevent overheating of internal components. Do not obstruct fan louvers or cover them with labels or stickers.
© Copyright Lenovo 2011
1
Electrical safety
Observe the following rules when working on electrical equipment.
Important:
Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents.
Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.
• Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly.
• Do not work alone under hazardous conditions or near equipment that has hazardous voltages.
• Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
• Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer to power-off the wall box that supplies power to the machine, and to lock the wall box in the off position.
• If you need to work on a machine that has exposed electrical circuits, observe the following precautions:
– Ensure that another person, familiar with the power-off controls, is near you.
Attention: Another person must be there to switch off the power, if necessary.
– Use only one hand when working with powered-on electrical equipment; keep the other hand in your pocket or behind your back.
Attention: An electrical shock can occur only when there is a complete circuit. By observing the above
rule, you may prevent a current from passing through your body.
– When using testers, set the controls correctly and use the approved probe leads and accessories for that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages; Instructions for these precautions are in the safety sections of maintenance information. Use extreme care when measuring high voltages.
• Regularly inspect and maintain your electrical hand tools for safe operational condition.
• Do not use worn or broken tools and testers.
• Never assume that power has been disconnected from a circuit. First, check that it has been powered off.
• Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds.
• Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage.
• Do not service the following parts with the power on when they are removed from their normal operating places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
– Similar units to listed above
This practice ensures correct grounding of the units.
• If an electrical accident occurs:
2
Hardware Maintenance Manual
– Use caution; do not become a victim yourself.
– Switch off power.
– Send another person to get medical aid.
Safety inspection guide
The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service technicians from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-ThinkPad features or options not covered by this inspection guide.
If any unsafe conditions are present, you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem.
Consider these conditions and the safety hazards they present:
• Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal electrical shock)
• Explosive hazards, such as a damaged CRT face or a bulging capacitor
• Mechanical hazards, such as loose or missing hardware
To determine whether there are any potentially unsafe conditions, use the following checklist at the beginning of every service task. Begin the checks with the power off, and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Power off the computer. Disconnect the power cord.
3. Check the power cord for: a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground continuity for 0.1 ohm or less between the external ground pin and the frame ground.
b. The power cord should be the type specified in the parts list.
c. Insulation must not be frayed or worn.
4. Check for cracked or bulging batteries.
5. Remove the cover.
6. Check for any obvious non-ThinkPad alterations. Use good judgment as to the safety of any non-ThinkPad alterations.
7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage.
8. Check for worn, frayed, or pinched cables.
9. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with.
Handling devices that are sensitive to electrostatic discharge
Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects.
Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge.
Notes:
1. Use product-specific ESD procedures when they exceed the requirements noted here.
Chapter 1
.
Safety information
3
2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.
When handling ESD-sensitive parts:
• Keep the parts in protective packages until they are inserted into the product.
• Avoid contact with other people.
• Wear a grounded wrist strap against your skin to eliminate static on your body.
• Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap.
• Use a grounded work mat to provide a static-free work surface. The mat is especially useful when handling ESD-sensitive devices.
• Select a grounding system, such as those listed below, to provide protection that meets the specific service requirement.
Note: The use of a grounding system to guard against ESD damage is desirable but not necessary.
– Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground.
– When working on a double-insulated or battery-operated system, use an ESD common ground or reference point. You can use coax or connector-outside shells on these systems.
– Use the round ground prong of the ac plug on ac-operated computers.
Grounding requirements
Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician.
Safety notices (multilingual translations)
The safety notices in this section are provided in the following languages:
DANGER
DANGER
4
Hardware Maintenance Manual
DANGER
DANGER
DANGER
DANGER
DANGER
Chapter 1
.
Safety information
5
DANGER
6
Hardware Maintenance Manual
PERIGO
PERIGO
PERIGO
Chapter 1
.
Safety information
7
PERIGO
PERIGO
PERIGO
PERIGO
PERIGO
DANGER
8
Hardware Maintenance Manual
DANGER
DANGER
DANGER
DANGER
DANGER
Chapter 1
.
Safety information
9
DANGER
DANGER
VORSICHT
VORSICHT
VORSICHT
10
Hardware Maintenance Manual
VORSICHT
VORSICHT
VORSICHT
VORSICHT
VORSICHT
Chapter 1
.
Safety information
11
12
Hardware Maintenance Manual
Chapter 1
.
Safety information
13
14
Hardware Maintenance Manual
Chapter 1
.
Safety information
15
16
Hardware Maintenance Manual
Laser compliance statement (multilingual translations)
The laser compliance statements in this section are provided in the following languages:
Chapter 1
.
Safety information
17
18
Hardware Maintenance Manual
Chapter 1
.
Safety information
19
20
Hardware Maintenance Manual
Chapter 1
.
Safety information
21
22
Hardware Maintenance Manual
Chapter 1
.
Safety information
23
24
Hardware Maintenance Manual
Chapter 2. Important service information
This chapter presents following important service information that applies to all machine types supported by this manual:
•
“Strategy for replacing FRUs” on page 25
–
“Strategy for replacing a hard disk drive” on page 26
–
“Important notice for replacing a system board” on page 26
–
“How to use error message” on page 26
•
“Strategy for replacing FRUs for CTO, CMV, and GAV” on page 26
–
“Product definition” on page 26
–
“FRU identification for CTO, CMV, and GAV products” on page 27
Important:
• Advise customers to contact the Lenovo Customer Support Center if they need any assistance in obtaining or installing any software fixes, drivers, and BIOS downloads. Telephone numbers for Lenovo
Support are available at: http://www.lenovo.com/support/phone
• System Disassembly/Reassembly videos that show the FRU removals or replacements for the Lenovo
® authorized service technicians are available in the following support site: http://www.lenovoservicetraining.com/ion/
Strategy for replacing FRUs
Before replacing parts:
Make sure that all software fixes, drivers, and BIOS downloads are installed before replacing any FRUs listed in this manual.
After a system board is replaced, ensure that the latest BIOS is loaded to the system board before completing the service action.
To download software fixes, drivers, and BIOS, do as follows:
1. Go to http://support.lenovo.com.
2. Enter the product number of the computer or press Auto-detect button on the screen.
3. Select Downloads & Drivers.
4. Follow the directions on the screen and install the necessary software.
Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs:
• If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall
the original FRU before you continue.
• Some computers have both a processor board and a system board. If you are instructed to replace either the processor board or the system board, and replacing one of them does not correct the problem, reinstall that board, and then replace the other one.
• If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error.
Before replacing the adapter or device, remove the FRUs, one by one, to see if the symptoms change.
Replace only the FRU that changed the symptoms.
Attention: The setup configuration on the computer you are servicing may have been customized. Running
Automatic Configuration may alter the settings. Note the current configuration settings (using the View
Configuration option); then, when service has been completed, verify that those settings remain in effect.
© Copyright Lenovo 2011
25
Strategy for replacing a hard disk drive
Always try to run a low-level format before replacing a hard disk drive. This will cause all customer data on the hard disk to be lost. Be sure that the customer has a current backup of the data before doing this task.
Attention: The drive startup sequence in the computer you are servicing may have been changed. Be
extremely careful during write operations such as copying, saving, or formatting. If you select an incorrect drive, data or programs can be overwritten.
If your computer is shipped with an mSATA drive and a solid state drive or hard disk drive, the mSATA drive will be seen as hard disk 0 in the system, and assigned drive C:. The solid state drive or hard disk drive will be seen as hard disk 1, and assigned drive D:. The mSATA drive is installed in the wireless WAN card slot of the computer. The Lenovo preloaded software is installed on the mSATA drive.
Important notice for replacing a system board
Some components mounted on a system board are very sensitive. Improper handling of a system board can cause damage to those components, and may cause a system malfunction.
Attention: When handling a system board:
• Do not drop a system board or apply any excessive force to it.
• Avoid rough handling of any kind.
• Avoid bending a system board and hard pushing to prevent cracking at each BGA (Ball Grid Array) chipset.
How to use error message
Use the error codes displayed on the screen to diagnose failures. If more than one error code is displayed, begin the diagnosis with the first error code. Whatever causes the first error code may also cause false error codes. If no error code is displayed, see whether the error symptom is listed in the Symptom-to-FRU
Index for the computer you are servicing.
Strategy for replacing FRUs for CTO, CMV, and GAV
Product definition
Dynamic Configure To Order (CTO)
This provides the ability for a customer to configure an IBM
® or a Lenovo solution from an eSite, and have this configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label, Product Entitlement Warehouse (PEW), eSupport, and the HMM will load these products as the 4-digit
MT and 3-digit model, where model = “CTO” (Example: 1829-CTO).
Custom Model Variant (CMV)
This is a unique configuration that has been negotiated between IBM or Lenovo and the customer. A unique
4-digit MT and 3-digit model is provided to the customer to place orders (Example: 1829-W15). A CMV is a special bid offering. Therefore, it is NOT generally announced.
• The MTM portion of the machine label is the 4-digit MT and 3-digit model, where model = “CTO”
(Example: 1829-CTO). The PRODUCT ID portion of the machine label is the 4-digit MT and 3-digit CMV model (Example: 1829-W15).
• The PEW record is the 4-digit MT and 3-digit model, where model = “CTO” (Example: 1829-CTO).
• eSupport will show both the CTO and CMV machine type models (Example: 1829-CTO and 1829-W15 will be found on the eSupport site.)
26
Hardware Maintenance Manual
• The HMM will have the 4-digit MT and 3-digit CTO model only (Example: 1829-CTO). Again, CMVs are custom models and are not found in the HMM.
General Announce Variant (GAV)
This is a standard model (fixed configuration). GAVs are announced and offered to all customers. The MTM portion of the machine label is a 4-digit MT and 3-digit model, where model = a “fixed part number”, not
“CTO” (Example: 1829-F1U). Also, PEW, eSupport, and the HMM will list these products under the same fixed model number.
FRU identification for CTO, CMV, and GAV products
There are three information resources to identify which FRUs are used to support CTO, CMV, and GAV products. These sources are PEW, eSupport, and the HMM.
Using PEW
• PEW is the primary source for identifying FRU part numbers and FRU descriptions for the key commodities for CTO, CMV and GAV products at a MT - serial number level. An example of key commodities are hard disk drives, system boards, microprocessors, Liquid Crystal Displays (LCDs), and memory.
• Remember, all CTO and CMV products are loaded in PEW under the 4-digit MT and 3-digit model, where model = “CTO” (Example: 1829-CTO). GAVs are loaded in PEW under the 4-digit MT and 3-digit model, where model = a “fixed part number”, not “CTO” (Example: 1829-F1U).
• PEW can be accessed at the following Web site: http://www.lenovo.com/support/site.wss/document.do?lndocid=LOOK-WARNTY
Select Warranty lookup. Input the MT and the Serial number and the list of key commodities will be returned in the PEW record under COMPONENT INFORMATION.
Using eSupport
For key commodities (examples - hard disk drive, system board, microprocessor, LCD, and memory)
• eSupport can be used to view the list of key commodities built in a particular machine serial (this is the same record found in PEW).
• eSupport can be accessed at the following Web site: http://support.lenovo.com
• To view the key commodities, do the following:
1. Click Products & Service Warranty.
2. Click Check Warranty Status.
3. On the Warranty Status Lookup page, click Parts Lookup.
4. Type your machine type and serial number, and then click Submit. The key commodities will be displayed.
For the remaining FRUs (the complete list of FRUs at the MT model level)
• eSupport can be used to view the complete list of FRUs for a machine type and model.
• To view the complete list of FRUs, do the following:
1. Click Product & Parts Detail and then follow the instructions on the screen to reach the Product and Parts Details page.
2. Click the Parts Detail tab to view the list of service parts.
Using the HMM
For key commodities (examples - hard disk drive, system board, microprocessor, LCD, and memory)
Chapter 2
.
Important service information
27
Use the HMM as a backup to PEW and eSupport to view the complete list of FRUs at the MT model level.
28
Hardware Maintenance Manual
Chapter 3. General checkout
This chapter presents following information:
•
•
–
“Diagnostics using PC-Doctor for DOS” on page 30
–
“Lenovo ThinkVantage Toolbox” on page 33
–
•
“Power system checkout” on page 34
The descriptions in this chapter apply to any ThinkPad model that supports the PC-Doctor
® diagnostics program. Some descriptions might not apply to your particular computer.
for DOS
Before you go to the checkout guide, be sure to read the following important notes.
Important notes:
• Only certified trained personnel should service the computer.
• Before replacing any FRU, read the entire page on removing and replacing FRUs.
• When you replace FRUs, use new nylon-coated screws.
• Be extremely careful during such write operations as copying, saving, or formatting. Drives in the computer that you are servicing sequence might have been altered. If you select an incorrect drive, data or programs might be overwritten.
• Replace a FRU only with another FRU of the correct model. When you replace a FRU, make sure that the model of the machine and the FRU part number are correct by referring to the FRU parts list.
• A FRU should not be replaced because of a single, unreproducible failure. Single failures can occur for a variety of reasons that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. Consider replacing a FRU only when a problem recurs. If you suspect that a FRU is defective, clear the error log and run the test again. If the error does not recur, do not replace the FRU.
• Be careful not to replace a nondefective FRU.
What to do first
When you do return a FRU, you must include the following information in the parts exchange form or parts return form that you attach to it:
1. Name and phone number of service technician
2. Date of service
3. Date on which the machine failed
4. Date of purchase
5. Failure symptoms, error codes appearing on the display, and beep symptoms
6. Procedure index and page number in which the failing FRU was detected
7. Failing FRU name and part number
8. Machine type, model number, and serial number
9. Customer's name and address
Note: During the warranty period, the customer may be responsible for repair costs if the computer damage
was caused by misuse, accident, modification, unsuitable physical or operating environment, or improper maintenance by the customer. Following is a list of some common items that are not covered under warranty and some symptoms that might indicate that the system was subjected to stress beyond normal use.
Before checking problems with the computer, determine whether the damage is covered under the warranty by referring to the following list:
The following are not covered under warranty:
• LCD panel cracked from the application of excessive force or from being dropped
© Copyright Lenovo 2011
29
• Scratched (cosmetic) parts
• Distortion, deformation, or discoloration of the cosmetic parts
• Plastic parts, latches, pins, or connectors that have been cracked or broken by excessive force
• Damage caused by liquid spilled into the system
• Damage caused by the improper insertion of a PC Card or the installation of an incompatible card
• Improper disc insertion or use of an optical drive
• Diskette drive damage caused by pressure on the diskette drive cover, foreign material in the drive, or the insertion of a diskette with multiple labels
• Damaged or bent diskette eject button
• Fuses blown by attachment of a nonsupported device
• Forgotten computer password (making the computer unusable)
• Sticky keys caused by spilling a liquid onto the keyboard
• Use of an incorrect ac power adapter on laptop products
The following symptoms might indicate damage caused by nonwarranted activities:
• Missing parts might be a symptom of unauthorized service or modification.
• If the spindle of a hard disk drive becomes noisy, it may have been subjected to excessive force, or dropped.
Checkout guide
Use the following procedures as a guide in identifying and correcting problems with the ThinkPad Notebook.
Note: The diagnostic tests are intended to test only ThinkPad products. The use of non-ThinkPad products,
prototype cards, or modified options can lead to false indications of errors and invalid system responses.
1. Identify the failing symptoms in as much detail as possible.
2. Verify the symptoms. Try to re-create the failure by running the diagnostic test or by repeating the operation.
Diagnostics using PC-Doctor for DOS
The ThinkPad Notebook has a test program called PC-Doctor for DOS (hereafter called PC-Doctor.) You can detect errors by running the diagnostics test included in PC-Doctor.
Note: PC-Doctor for DOS is available at the following Web site:
http://support.lenovo.com
To create the PC-Doctor diagnostic CD, follow the instructions on the Web site.
For some possible configurations of the computer, PC-Doctor might not run correctly. To avoid this problem, you need to initialize the computer setup by use of the BIOS Setup Utility before you run PC-Doctor.
To enter BIOS Setup Utility, do as follows:
1. Turn on the computer.
2. When the ThinkPad logo comes up, immediately press F1 to enter the BIOS Setup Utility.
Note: If a supervisor password has been set by the customer, BIOS Setup Utility menu appears after the
password is entered. You can start the BIOS Setup Utility by pressing Enter instead of entering the supervisor password; however, you cannot change the parameters that are protected by the supervisor password.
On the BIOS Setup Utility screen, press F9, Enter, F10, and then Enter.
Note: When you initialize the computer configuration, some devices are disabled, such as the serial port. If
you test one of these devices, you will need to enable it by using Configuration utility for DOS. The utility is
30
Hardware Maintenance Manual
available on the following Web site: http://support.lenovo.com
PC-Doctor cannot be used to test a device that is in the docking station, even if the computer supports the docking station. To test a USB device, connect it to the USB connector of the computer.
Testing the computer
Note: The PC-Doctor for DOS CD-R/CD-RW disc supports only test of internal optical disc drives (CD-RW,
CD-RW/DVD Combo, and DVD Multi drives) on ThinkPad computers. It does not support test of any optical disc drives connected through USB devices, PC cards, CardBus cards, or similar. The USB limitation only applies to testing of the device. Using a bootable PC-Doctor for DOS CD/DVD, the system can be started from a USB attached optical drive.
To run the test, do as follows:
1. Turn off the computer.
2. Make sure that the internal optical drive that is supported as a startup device is attached to the computer you are servicing.
If an error code appears, go to “Symptom-to-FRU index” on page 41.
4. When the ThinkPad logo comes up, immediately press F12 to enter the Boot Menu.
5. Insert the PC-Doctor CD into the internal optical drive.
6. Press cursor keys to select ATAPI CDx (x: 0, 1, ...) and then press Enter.
7. Follow the instructions on the screen.
8. The main panel of PC-Doctor appears.
9. Select Diagnostics with the arrow keys, and press Enter.
Note: You can select an item not only with the arrow keys, but also with the TrackPoint
®
Instead of pressing Enter, click the left button.
pointer.
A pull-down menu appears. (Its exact form depends on the model.)
Note: PC-Doctor menu does not mean the formal support device list. Some unsupported device names
may appear in the PC-Doctor menu.
Diagnostics Interactive Tests
Run Normal Test
Run Quick Test
CPU/Coprocessor
Systemboard
Video Adapter
Fixed Disks
Diskette Drives
Other Devices
Communication
Wireless LAN
Advanced Memory Tests
Hardware Info Utility Quit F1=Help
PC-DOCTOR 2.0 Copyright 2008 PC-Doctor, Inc. All Rights Reserved.
Use the cursor keys and ESC to move in menus. Press ENTER to select.
The options on the test menu are as follows:
Chapter 3
.
General checkout
31
Diagnostics
• Run Normal Test
• Run Quick Test
• CPU/Coprocessor
• Systemboard
• Video Adapter
• Serial Ports
• Fixed Disks
• Diskette Drives
• Other Devices
• Wireless LAN
• Advanced Memory Tests
Notes:
Interactive Tests
• Keyboard
• Video
• Internal Speaker
• Mouse
• Diskette
• System Load
• Optical Drive Test
• Intel WLAN Radio Test
• In the Keyboard test in Interactive Tests, the Fn key should be held down for at least 2 seconds; otherwise, it cannot be sensed.
• Video Adapter test supports only the LCD display on the ThinkPad Notebook. If you have an external monitor attached to the computer, detach it before running PC-Doctor for DOS.
• To test Digital Signature Chip, the security chip must be set to Active.
10. Run the applicable function test.
11. Follow the instructions on the screen. If there is a problem, PC-Doctor shows messages describing it.
12. To exit the test, select Quit — Exit Diag. To cancel the test, press Esc.
Note: After running PC-Doctor, check the time and date on the system and reset them if they are incorrect.
Detecting system information with PC-Doctor
PC-Doctor can detect the following system information:
Hardware Info
System Configuration
Memory Contents
Physical Disk Drives
Logical Disk Drives
VGA Information
IDE Drive Info
PCI Information
PNPISA Info
SMBIOS Info
VESA LCD Info
Hardware Events Log
Utility
Run External Tests
Surface Scan Hard Disk
Benchmark System
DOS Shell
Tech Support Form
Battery Rundown
View Test Log
Print Log
Save Log
Full Erase Hard Drive
Quick Erase Hard Drive
32
Hardware Maintenance Manual
Lenovo ThinkVantage Toolbox
Lenovo ThinkVantage
®
Toolbox is a diagnostic program that works through the Windows
® operating system.
It enables you to view symptoms of computer problems and solutions for them, and includes automatic notification when action is required, computing assistance, advanced diagnostics, and diagnostic history.
Note: To install the latest Lenovo ThinkVantage Toolbox on the computer, go to
http://web.lenovothinkvantagetoolbox.com/, click Download Lenovo ThinkVantage Toolbox, and follow the instructions on the screen.
To run this program, do as follows:
Windows 7:
Click Start ➙ Control Panel ➙ System and Security ➙ Lenovo - System Health and Diagnostics.
Windows Vista
®
and Windows XP:
Click Start ➙ All Programs ➙ ThinkVantage ➙ Lenovo ThinkVantage Toolbox.
Follow the instructions on the screen. Lenovo ThinkVantag Toolbox also has problem determination aids that determine software and usage problems.
For additional information about this program, see the Help for the program.
FRU tests
The following table shows the test for each FRU.
Table 1. FRU tests
FRU
System board
Applicable test
1. Diagnostics ➙ CPU/Coprocessor
2. Diagnostics ➙ Systemboard
3. If the docking station or the port replicator is attached to the ThinkPad computer, detach it.
4. Place the computer on a horizontal surface, and run Diagnostics ➙ ThinkPad
Devices ➙ HDD Active Protection Test.
Power
LCD unit
Audio
Speaker
Keyboard
Hard disk drive or solid state drive
Diskette drive
Note: Do not apply any physical shock to the computer while the test is running.
Diagnostics ➙ ThinkPad Devices ➙ AC Adapter ➙ Battery 1 (Battery 2)
1. Diagnostics ➙ Video Adapter
2. Interactive Tests ➙ Video
Enter the BIOS Setup Utility and change Serial ATA (SATA) setting to Compatibility, and run Diagnostics ➙ Other Device ➙ Codec Test
Interactive Tests ➙ Internal Speaker
Note: Once Audio test is done, the no sound is heard this test. In this case, turn off and turn on the computer. Then, run this test again.
1. Diagnostics ➙ Systemboard ➙ Keyboard
2. Interactive Tests ➙ Keyboard
Enter the BIOS Setup Utility and change Serial ATA (SATA) setting to Compatibility, and run Diagnostics ➙ Fixed Disks
1. Diagnostics ➙ Diskette Drives
2. Interactive Tests ➙ Diskette
Chapter 3
.
General checkout
33
Table 1. FRU tests (continued)
FRU Applicable test
Optical drive
Memory
TrackPoint or pointing device
1. Diagnostics ➙ Other Devices ➙ Optical Drive
2. Interactive Tests ➙ Optical Drive Test
1. If two DIMMs are installed, remove one of them and run Diagnostics ➙ Advanced
Memory Tests.
2. If the problem does not recur, return the DIMM to its place, remove the other one, and run the test again.
If the TrackPoint does not work, check the configuration as specified in the BIOS Setup
Utility. If the TrackPoint is disabled, select Automatic to enable it.
After you use the TrackPoint, the pointer may drift on the screen for a short time. This drift can occur when a slight, steady pressure is applied to the TrackPoint pointer.
This symptom is not a hardware problem. If the pointer stops after a short time, no service action is necessary.
Touch Pad
If enabling the TrackPoint does not correct the problem, continue with the following:
• Interactive Tests ➙ Mouse
If the Touch Pad does not work, check the configuration as specified in the BIOS Setup
Utility. If the Touch Pad is disabled, select Automatic to enable it. If enabling the Touch
Pad does not correct the problem, continue with the following:
• Interactive Tests ➙ Mouse
Power system checkout
To verify a symptom, do the following:
1. Turn off the computer.
2. Remove the battery pack.
3. Connect the ac power adapter.
4. Check that power is supplied when you turn on the computer.
5. Turn off the computer.
6. Disconnect the ac power adapter and install the charged battery pack.
7. Check that the battery pack supplies power when you turn on the computer.
If you suspect a power problem, see the appropriate one of the following power supply checkouts:
•
“Checking the ac power adapter” on page 34
•
“Checking operational charging” on page 35
•
“Checking the battery pack” on page 35
•
“Checking the backup battery” on page 36
Checking the ac power adapter
You are here because the computer fails only when the ac power adapter is used.
• If the power problem occurs only when the docking station or the port replicator is used, replace the docking station or the port replicator.
• If the power-on indicator does not turn on, check the power cord of the ac power adapter for correct continuity and installation.
To check the ac power adapter, do the following:
1. Unplug the ac power adapter cable from the computer.
2. Measure the output voltage at the plug of the ac power adapter cable. See the following figure:
34
Hardware Maintenance Manual
3
2
1
(20V)
Pin
1
2
3
Voltage (V dc)
+20
0
Ground
Note: Output voltage of pin no.2 of the ac power adapter may different from the one you are servicing.
3. If the voltage is not correct, replace the ac power adapter.
4. If the voltage is acceptable, do the following:
• Replace the system board.
• If the problem persists, go to “FRU tests” on page 33.
Note: Noise from the ac power adapter does not always indicate a defect.
Checking operational charging
To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer.
Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon still does not turn on, replace the battery pack.
If the charge indicator still does not turn on, replace the system board. Then reinstall the battery pack. If it is still not charged, go to the next section.
Checking the battery pack
Battery charging does not start until the Power Manager Battery Gauge shows that less than 96% of the total power remains; under this condition the battery pack can charge to 100% of its capacity. This protects the battery pack from being overcharged or from having a shortened life.
To check your battery, move your cursor to the Power Manager Battery Gauge icon in the icon tray of the
Windows taskbar and wait for a moment (but do not click), and the percentage of battery power remaining is displayed. To get detailed information about the battery, double-click the Power Manager Battery
Gauge icon.
Note: If the battery pack becomes hot, it may not be able to charge. Remove it from the computer and leave
it at room temperature for a while. After it cools down, reinstall and recharge it.
To check the battery pack, do the following:
1. Power off the computer.
2. Remove the battery pack and measure the voltage between battery terminals 1 (+) and 7 (-). See the following figure:
Chapter 3
.
General checkout
35
Terminal
1
7
Voltage (V dc)
+ 0 to + 12.6
Ground (-)
1(+)
2(+)
3
4 5
6(-)
7(-)
3. If the voltage is less than +11.0 V dc, the battery pack has been discharged.
Note: Recharging will take at least 3 hours, even if the indicator does not turn on.
If the voltage is still less than +11.0 V dc after recharging, replace the battery.
4. If the voltage is more than +11.0 V dc, measure the resistance between battery terminals 5 and 7.
The resistance must be 4 to 30 K Ω.
If the resistance is not correct, replace the battery pack. If the resistance is correct, replace the system board.
Checking the backup battery
Do the following:
1. Power off the computer, and unplug the ac power adapter from it.
2. Turn the computer upside down.
3. Remove the battery pack (see “1010 Battery pack” on page 57).
4. Remove the backup battery (see “1140 Backup battery” on page 78).
5. Measure the voltage of the backup battery. See the following figure.
Wire
Red
Black
Voltage (V dc)
+2.5 to +3.2
Ground
• If the voltage is correct, replace the system board.
• If the voltage is not correct, replace the backup battery.
• If the backup battery discharges quickly after replacement, replace the system board.
36
Hardware Maintenance Manual
Chapter 4. Related service information
This chapter presents following information:
•
“Restoring the factory contents by using Recovery Disc Set” on page 37
•
•
•
“Symptom-to-FRU index” on page 41
Service Web site:
When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://support.lenovo.com.
Restoring the factory contents by using Recovery Disc Set
When the hard disk drive or solid state drive is replaced because of a failure, no product recovery program is on the new hard disk. In this case, you must use the Recovery Disc Set for the computer. Order the
Recovery Disc Set and the hard disk drive at the same time so that you can recover the new hard disk drive
The recovery disc set consists of the user instructions and the following set of DVDs to restore the computer to the original factory configuration.
Operating System Recovery Disc (one disc)
This disc restores the Microsoft
®
Windows operating system. Use this disc to start the recovery process.
Applications and Drivers Recovery Disc (one or more discs)
This disc restores the preinstalled applications and drivers on the computer.
Supplemental Recovery Disc
This disc contains additional content, such as updates to the software that was preinstalled on the computer. Not all recovery disc sets come with a Supplemental Recovery Disc.
Notes:
• You must have a DVD drive to use the recovery discs. If you do not have an internal DVD drive, you can use an external USB DVD drive.
• During the recovery process, all data on the drive will be deleted. If possible, copy any important data or personal files that you want to keep onto removable media or a network drive before you start the recovery process.
To restore the computer to the original factory configuration using the recovery disc set, do the following:
Note: Recovery can take one to two hours to complete. The length of time depends on the method you use. If you use recovery discs, the recovery process will take about two hours.
1. Make the CD/DVD drive the first startup device in the startup sequence using the following procedure: a. Press and hold down the F1 key, and then turn on the computer. When the logo screen is displayed or if you hear repeating beeps, release the F1 key. The Setup Utility program opens.
b. Use the arrow keys to select Startup ➙ Boot.
c. Select the CD/DVD drive as the 1st Boot Device.
2. Insert the Operating System Recovery Disc into the DVD drive.
© Copyright Lenovo 2011
37
3. Press F10 to save the Setup Utility configuration changes. Follow the instructions on the screen to begin the recovery process.
4. Select your language and click Next.
5. Read the license. If you agree with the terms and conditions, select I accept these terms and
conditions and then click Next. If you do not agree with the terms and conditions, follow the
instructions on the screen.
6. Click Yes in the displayed window to begin the operating system recovery process.
7. Insert the Applications and Drivers Recovery Disc when prompted and then click OK to begin the applications and drivers recovery process.
8. If you have a Supplemental Recovery Disc, insert it when prompted and click Yes. If you do not have a
Supplemental Recovery Disc, click No.
9. When all of the data has been copied from the last disc in the set and has been processed, remove the disc and restart the computer.
Note: The rest of the recovery process is fully automated and no action is required by you. The
computer will restart into the Microsoft Windows desktop several times and you might experience periods when no activity is apparent on the screen for several minutes at a time. This is normal.
10. When the recovery process is complete, the Set Up Windows screen is displayed. Follow the instructions on the screen to complete the Windows setup.
11. After you have completed the Windows setup, you might want to restore the original startup sequence.
Start the Setup Utility program and then press F9 to restore the default settings. Press F10 to save and exit the Setup Utility.
Note: After restoring a hard disk drive to the factory default settings, you might need to reinstall some
device drivers.
Passwords
As many as three passwords may be needed for any ThinkPad Notebook: the power-on password (POP), the hard-disk password (HDP), and the supervisor password (SVP).
If any of these passwords has been set, a prompt for it appears on the screen whenever the computer is turned on. The computer does not start until the password is entered.
Note: If only an SVP is installed, the password prompt does not appear when the operating system is booted.
Power-on password
A power-on password (POP) protects the system from being powered on by an unauthorized person. The password must be entered before an operating system can be booted. For how to remove the POP, see
“How to remove the power-on password” on page 39.
Hard-disk password
There are two hard-disk passwords (HDPs):
• User HDP—for the user
• Master HDP—for the system administrator, who can use it to get access to the hard disk even if the user has changed the user HDP
Note: There are two modes for the HDP: User only and Master + User. The Master + User mode requires
two HDPs; the system administrator enters both in the same operation. The system administrator then provides the user HDP to the system user.
38
Hardware Maintenance Manual
Attention: If the user HDP has been forgotten, check whether a master HDP has been set. If it has, it can be
used for access to the hard disk drive. If no master HDP is available, neither Lenovo nor Lenovo authorized service technicians provide any services to reset either the user or the master HDP, or to recover data from the hard disk drive. The hard disk drive can be replaced for a scheduled fee.
For how to remove the POP, see “How to remove the hard-disk password” on page 39.
Supervisor password
A supervisor password (SVP) protects the system information stored in the BIOS Setup Utility. The user must enter the SVP in order to get access to the BIOS Setup Utility and change the system configuration.
Attention: If the SVP has been forgotten and cannot be made available to the service technician, there is no
service procedure to reset the password. The system board must be replaced for a scheduled fee.
How to remove the power-on password
To remove a POP that you have forgotten, do the following:
(A) If no SVP has been set:
1. Turn off the computer.
2. Remove the battery pack. For how to remove the battery pack, see “1010 Battery pack” on page 57.
4. Turn on the computer and wait until the POST ends. After the POST ends, the password prompt does not appear. The POP has been removed.
5. Reinstall the backup battery and the battery pack.
(B) If an SVP has been set and is known by the service technician:
1. Turn on the computer.
2. When the ThinkPad logo comes up, immediately press F1 to enter BIOS Setup Utility. For models supporting the Passphrase function, press F1 while the POP icon is appearing on the screen; then enter the POP. For the other models, enter the POP.
Note: To check whether the ThinkPad Notebook you are servicing supports the Passphrase function,
enter the BIOS Setup Utility and go to Security ➙ Password. If the Using Passphrase item is displayed in the menu, this function is available on the ThinkPad Notebook.
3. Select Security, using the cursor directional keys to move down the menu.
4. Select Password.
5. Select Power-On Password.
6. Type the current SVP in the Enter Current Password field. then leave the Enter New Password field blank, and press Enter twice.
7. In the Changes have been saved window, press Enter.
8. Press F10; then, in the Setup Confirmation window, select Yes.
How to remove the hard-disk password
Attention: If User only mode is selected and the user HDP has been forgotten and cannot be made
available to the service technician, neither Lenovo nor Lenovo authorized service technicians provide any services to reset the user HDPs or to recover data from the hard disk drive. The hard disk drive can be replaced for a scheduled fee.
Chapter 4
.
Related service information
39
To remove a user HDP that has been forgotten, when the SVP and the master HDP are known, do the following:
1. Turn on the computer.
2. When the ThinkPad logo comes up, immediately press F1 to enter BIOS Setup Utility. For models supporting the Passphrase function, press F1 while HDP icon is appearing on the screen; then enter the master HDP. For the other models, enter the master HDP.
Note: To check whether the ThinkPad Notebook you are servicing supports the Passphrase function,
enter the BIOS Setup Utility and go to Security ➙ Password. If Using Passphrase item is displayed in the menu, this function is available on the ThinkPad Notebook.
3. Select Security, using the cursor directional keys to move down the menu.
4. Select Password.
5. Select Hard-disk x password, where x is the letter of the hard disk drive. A pop-up window opens.
6. Select Master HDP.
7. Type the current master HDP in the Enter Current Password field. then leave the Enter New Password field blank, and press Enter twice.
8. Press F10.
9. Select Yes in the Setup Confirmation window. Both user HDP and master HDP will have been removed.
Power management
To reduce power consumption, the computer has three power management modes: screen blank, sleep
(standby in Windows XP), and hibernation.
Screen blank mode
If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off.
To put the computer into screen blank mode, do as follows:
1. Press Fn+F3. A panel for selecting a power plan (in Windows XP, power scheme) appears.
2. Select Power off display (keep current power plan) (in Windows XP, keep current power scheme).
To end screen blank mode and resume normal operation, press any key.
Sleep (standby) mode
When the computer enters sleep (standby) mode, the following events occur in addition to what occurs in screen blank mode:
• The LCD is powered off.
• The hard disk drive is powered off.
• The CPU stops.
To enter sleep (standby) mode, press Fn+F4.
Note: You can change the action of the Fn+F4 key combination by changing the settings in Power Manager.
In certain circumstances, the computer goes into sleep (standby) mode automatically:
• If a “suspend time” has been set on the timer, and the user does not do any operation with the keyboard, the TrackPoint, the hard disk, the parallel connector, or the diskette drive within that time.
• If the battery indicator blinks orange, indicating that the battery power is low.
40
Hardware Maintenance Manual
Note: Even if you do not set the low-battery alarm, the charge indicator notifies you when the battery is low,
and then the computer enters the power-saving mode automatically.
To cause the computer to return from sleep (standby) mode and resume operation, do one of the following:
• Press the Fn key.
• Open the LCD cover.
• Turn on the power switch.
Also, in either of the following events, the computer automatically returns from sleep (standby) mode and resumes operation:
• The ring indicator (RI) is signaled by a serial device or a PC Card device.
• The time set on the resume timer elapses.
Note: The computer does not accept any input immediately after it enters sleep (standby) mode. Wait a
few seconds before taking any action to reenter operation mode.
Hibernation mode
In hibernation mode, the following occurs:
• The system status, RAM, VRAM, and setup data are stored on the hard disk.
• The system is powered off.
Note: If the computer enters the hibernation mode while it is docked to the docking station, do not undock it
before resuming normal operation. If you do undock it and then try to resume normal operation, you will get an error message, and you will have to restart the system.
To cause the computer to enter hibernation mode, do any of the following:
• Press the Fn+F12 keys.
• If you are using the APM operating system and have set the mode to Power switch mode [Hibernation], turn off the power switch.
• If you are using the ACPI operating system and have defined one of the following actions as the event that causes the system to go into hibernation mode, perform that action.
– Closing the lid.
– Pressing the power button.
– Pressing Fn+F4 keys.
Also, the computer goes into hibernation mode automatically in either of the following conditions:
• If a “hibernation time” has been set on the timer, and if the user does not do any operation with the keyboard, the TrackPoint, the hard disk drive, the parallel connector, or the diskette drive within that time.
• If the timer conditions are satisfied in suspend mode.
• If you are using the APM operating system and have set the mode to Hibernate when battery becomes
low, and the battery charge becomes critically low.
When the power is turned on, the computer returns from hibernation mode and resumes operation. The hibernation file in the boot record on the hard disk drive is read, and system status is restored from the hard disk drive.
Symptom-to-FRU index
This section contains following information:
•
“Numeric error codes” on page 42
Chapter 4
.
Related service information
41
•
•
•
“LCD-related symptoms” on page 44
•
“Intermittent problems” on page 45
•
“Undetermined problems” on page 45
The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first, in boldface type.
Note: Do the FRU replacement or other actions in the sequence shown in the column headed “FRU or
action, in sequence.” If replacing a FRU does not solve the problem, put the original part back in the computer. Do not replace a nondefective FRU.
This index can also help you determine, during regular servicing, what FRUs are likely to need to be replaced next.
A numeric error is displayed for each error detected in POST or system operation. In the displays, n can be any number.
If no numeric code is displayed, check the narrative descriptions of symptoms. If the symptom is not
described there, go to “Intermittent problems” on page 45.
Note: For a device not supported by diagnostic codes in the ThinkPad Notebooks, see the manual for
that device.
Numeric error codes
Table 2. Numeric error codes
Symptom or error (beeps, if any)
0187
EAIA data access error—The access to EEPROM is failed.
(two short beeps)
0189
Invalid RFID configuration information area—The
EEPROM checksum is not correct.
(two short beeps)
0190
Critical low-battery error
(two short beeps)
0191
System Security—Invalid Remote Change requested.
FRU or action, in sequence
System board.
System board.
1. Charge the battery pack.
2. Battery pack.
1. Run BIOS Setup Utility, and then save current
setting by pressing F10.
2. System board.
Change keyboard, and restart the computer.
0210
Stuck Key
(two short beeps)
0211
Keyboard error
(two short beeps)
0230
Shadow RAM error—Shadow RAM fails at offset nnnn.
(two short beeps)
0231
System RAM error—System RAM fails at offset nnnn.
(two short beeps)
Run interactive tests of the keyboard and the auxiliary input device.
System board.
1. DIMM.
2. System board.
42
Hardware Maintenance Manual
Table 2. Numeric error codes (continued)
Symptom or error (beeps, if any)
0232
Extended RAM error— Extended RAM fails at offset nnnn.
(two short beeps)
0250
System battery error—System battery is dead.
(two short beeps)
0251
System CMOS checksum bad— Default configuration used.
(two short beeps)
0254
System NV7 Volume checksum bad- Default configuration used
(two short beeps)
0260
System timer error.
(two short beeps)
FRU or action, in sequence
1. DIMM.
2. System board.
1. Charge the backup battery for more than 8 hours
by connecting the ac power adapter.
2. Replace the backup battery and run BIOS Setup
Utility to reset the time and date.
1. Charge the backup battery for more than 8 hours
by connecting the ac power adapter.
2. Replace the backup battery and run BIOS Setup
Utility to reset the time and date.
Turn off the computer and discharge CMOS. Then restart the computer.
0270
Real-time clock error.
(two short beeps)
1. Charge the backup battery for more than 8 hours
by connecting the ac power adapter.
2. Replace the backup battery and run BIOS Setup
Utility to reset the time and date.
3. System board.
1. Charge the backup battery for more than 8 hours
by connecting the ac power adapter.
2. Replace the backup battery and run BIOS Setup
Utility to reset the time and date.
3. System board.
Run BIOS Setup Utility to reset the time and date.
0271
Date and time error—Neither the date nor the time is set in the computer.
(two short beeps)
0280
Previous boot incomplete— Default configuration used.
(two short beeps)
02D0
System cache error.
(two short beeps)
02F0
CPU ID: xx Failed.
1802
Unauthorized network card is plugged in—Turn off and remove the miniPCI network card.
(two short beeps)
1. Load “Setup Default” in BIOS Setup Utility.
2. DIMM.
3. System board.
1. CPU.
2. System board.
1. CPU.
2. System board.
1. Remove Mini PCI network card.
2. System board.
Chapter 4
.
Related service information
43
Error messages
Table 3. Error messages
Symptom or error (beeps, if any)
Bad CRC2. Enter BIOS Setup Utility, and load Setup defaults.
(two short beeps)
Fan error.
(four short beeps, one long beep)
FRU or action, in sequence
Press F1 to enter BIOS Setup Utility. Press F9, and
Enter to load the default setting. Then save the current setting by pressing F10, and restart the computer.
1. Fan.
2. Thermal grease.
3. System board.
Install the DRAM.
DRAM is unplugged.
(four short beeps, pause, three short beeps, pause, one short beep, pause, one short beep)
DRAM is not well plugged.
(seven short beeps, one long beep, four short beeps, one long beep, one short beep, one long beep, one short beep, one long beep till forever.)
Operating system not found.
Reinstall the DRAM.
1. Check that the operating system has no failure
and is installed correctly.
2. Enter BIOS Setup Utility and see whether the hard disk drive is properly identified. If you still see the same error message, check the boot sequence.
3. Reinstall the hard disk drive.
4. Reinstall the operating system.
Turn off the computer and remove the WAN card.
Unauthorized network card is plugged in - Power off and remove the miniPCI network card.
(two short beeps)
System Configuration Data Read Error
(two short beeps)
Press F1 to enter BIOS Setup Utility. Press F9, and
Enter to load the default setting. Then save the current setting by pressing F10, and restart the computer.
No-beep symptoms
Table 4. No-beep symptoms
Symptom or error
No beep, power-on indicator on, LCD blank, and no
POST.
No beep, power-on indicator on, and LCD blank during
POST.
The power-on password prompt appears.
The hard-disk password prompt appears.
FRU or action, in sequence
1. Make sure that every connector is connected
tightly and correctly.
2. DIMM.
3. System board.
1. Reseat DIMM.
2. System board.
A power-on password or a supervisor password is set.
Type the password and press Enter.
A hard-disk password is set. Type the password and press Enter.
LCD-related symptoms
Important: The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The
presence of a small number of dots that are missing, discolored, or always lighted is characteristic of TFT
LCD technology, but excessive pixel problems can cause viewing concerns.
44
Hardware Maintenance Manual
If the LCD you are servicing has two or less visible defective pixels, it should not be considered faulty.
However, if the LCD has three or more visible defective pixels, it will be deemed as defective by Lenovo and it should be replaced.
Notes:
• This policy applies to all ThinkPad Notebooks purchased on 1 January, 2008 or later.
• Lenovo will not provide replacement if the LCD is within specification as we cannot guarantee that any replacement LCD will have zero pixel defects.
• One pixel consists of R, G, B sub-pixels.
Table 5. LCD-related symptoms
Symptom or error
No beep, power-on indicator on, and a blank LCD during
POST.
• LCD backlight not working.
• LCD too dark.
• LCD brightness cannot be adjusted.
• LCD contrast cannot be adjusted.
• LCD screen unreadable.
• Characters missing pixels.
• Screen abnormal.
• Wrong color displayed.
Horizontal or vertical lines displayed on LCD.
FRU or action, in sequence
System board.
1. Reseat the LCD connectors.
2. LCD assembly.
3. System board.
1. See important note for “LCD-related symptoms.”
2. Reseat all LCD connectors.
3. LCD assembly.
4. System board.
LCD assembly.
Intermittent problems
Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs.
When analyzing an intermittent problem, do the following:
1. Run the diagnostic test for the system board in loop mode at least 10 times.
2. If no error is detected, do not replace any FRUs.
3. If any error is detected, replace the FRU shown by the FRU code. Rerun the test to verify that no more errors exist.
Undetermined problems
If the diagnostic tests did not identify the adapter or device that has failed, if wrong devices are installed, or if the system simply is not operating, follow these procedures to isolate the failing FRU (do not isolate
FRUs that have no defects).
Verify that all attached devices are supported by the computer.
1. Turn off the computer.
2. Visually check each FRU for damage. Replace any damaged FRU.
3. Remove or disconnect all of the following devices: a. Non-ThinkPad devices b. Devices attached to the docking station or the port replicator c. Printer, mouse, and other external devices
Chapter 4
.
Related service information
45
d. Battery pack e. Hard disk drive f. External diskette drive or optical drive g. DIMM h. Optical disk or diskette in the internal drive i.
PC Cards
4. Turn on the computer.
5. Determine whether the problem has been solved.
6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7. If the problem remains, replace the following FRUs one at a time (do not replace a nondefective FRU): a. System board b. LCD assembly
46
Hardware Maintenance Manual
Chapter 5. Status indicators
This chapter presents the system status indicators that show the status of the computer.
1
6
5
4
3
2
8
7
Table 6. Status indicators
Indicator
1
Numeric lock
Meaning
By default, when the numeric lock is on, the indicator is displayed on the screen.
2
Power on • Green: The computer is on and ready to use. The power switch stays lit whenever the computer is on and is not lit when the computer is in sleep (standby) mode.
3
Wireless
LAN/WAN/WiMAX status
• Green: The wireless feature (802.11 standard or 802.11n) is on, and the radio link is ready for use.
• Blinking green: Data is being transmitted.
4
Bluetooth wireless status
• Green: Bluetooth wireless is on, and the radio link is ready for use.
• Blinking green: Data is being transmitted.
© Copyright Lenovo 2011
47
Table 6. Status indicators (continued)
Indicator
5
Device access
Meaning
Data is being read from or written to the hard disk drive. When this indicator is on, do not put the computer into sleep (standby) mode or turn off the computer.
6
Caps lock
Note: Do not move the computer while this indicator is on. Sudden physical shock could cause drive errors.
Caps Lock mode is enabled.
7
Sleep (Standby) status
8
Battery status
• Green: The computer is in sleep (standby) mode.
• Blinking green: The computer is entering sleep (standby) mode or hibernation mode, or is resuming normal operation.
• Green: The battery is charged between 80% to 100% of the capacity, and being discharged between 0% to 80% of the capacity.
• Blinking green: The battery is charged between 20% to 80% of the capacity, and being charged. When the battery reaches 80% charge, blinking stops, but the charging might continue until the battery is 100% charged.
• Orange: The battery is charged between 5% and 20% of the capacity, and being discharged.
• Blinking orange (slow): The battery is charged between 5% to 20% of the capacity, and being charged. When it reaches 20%, the blinking color changes to green.
• Blinking orange: The battery is charged between 0% to 5% of the capacity.
• Blinking orange (rapid): An error has occurred in the battery.
• Off: The battery is fully charged or the battery is detached.
48
Hardware Maintenance Manual
Chapter 6. Fn key combinations
The following table shows the function of each combination of Fn with a function key.
Table 7. Fn key combinations
Key combination
Fn+F1
Fn+F2
Fn+F3
Description
Reserved.
Lock the computer.
Select a power plan (in Windows XP, power scheme) that has been created by Power Manager, or adjust the power level by using the slider control. When you press this combination, a panel for selecting a power plan (power scheme) appears.
Fn+F4
Notes:
1. To use the Fn+F3 key combination, you must have the ThinkPad PM device driver installed on the computer.
2. If you have logged on with an administrator user ID in Windows XP, and you press Fn+F3, the window for selecting a power scheme appears. If you have logged on with another user ID in Windows XP, and you press Fn+F3, the window does not appear.
3. You cannot turn off the computer display by pressing Fn+F3.
Put the computer in sleep (standby) mode. To return to normal operation, press the Fn key only, without pressing a function key.
Fn+F5
Fn+F6
Notes:
1. To use the Fn+F4 key combination, you must have the ThinkPad PM device driver installed on the computer.
2. If you want to use the combination to put the computer into hibernation mode or do-nothing mode (in Windows XP, shut the computer down or show the panel for turning off the computer), change the settings in the Power Manager.
Enable or disable the built-in wireless networking features and the Bluetooth features. If you press Fn+F5, a list of wireless features is displayed. You can quickly change the power state of each feature in the list.
Notes: If you want to use Fn+F5 to enable the feature specified in IEEE standard 802.11, the following device drivers must be installed on the computer beforehand:
• ThinkPad Power Management driver
• OnScreen Display Utility
• Wireless device drivers
Change the camera settings and the setting of the microphone mute button. When you press
Fn+F6, the camera setting window is opened.
Note: For Windows XP models, the setting of the microphone mute button cannot be changed.
© Copyright Lenovo 2011
49
Table 7. Fn key combinations (continued)
Key combination Description
Fn+F7 Apply a presentation scheme directly, with no need to start Presentation Director.
To disable this function and use the Fn+F7 key combination for switching a display output location, start Presentation Director, and change the settings.
Note: If the computer is a Windows 7 model, it does not support presentation schemes, but the Fn+F7 combination is available for switching a display output location.
For Windows 7:
Switch between the computer display and an external monitor. Windows will show these display options:
• Computer display only (LCD)
• Computer display and external monitor (same image)
• Computer display and external monitor (extended desktop)
• External monitor only
Note: To switch between the computer display and an external monitor, the Win+P key combination is also available.
For Windows Vista and Windows XP:
Switch between the computer display and an external monitor. If an external monitor is attached, computer output is displayed in the following three patterns by turns:
• External monitor (CRT display)
• Computer display and external monitor (LCD + CRT display
• Computer display (LCD)
Notes:
1. This function is not supported if different desktop images are displayed on the computer display and the external monitor (the Extend desktop function).
2. This function does not work while a DVD movie or a video clip is playing.
Fn+F8
Fn+F9
Fn+F10
Fn+F11
Fn+F12
Fn+PgUp
Fn+Home
Fn+End
Fn+Spacebar
Fn+PrtSc
To enable this function, start Presentation Director, and change the Fn+F7 settings.
Note: Multiple users can log on to a single operating system by using different user IDs. Each user needs to change the settings.
Change the settings of the UltraNav
® pointing device.
Reserved.
Reserved.
Reserved.
Put the computer into hibernation mode. To return to normal operation, press the power button for less than four seconds.
Note: To use Fn+F12 for hibernation, you must have the ThinkPad PM device driver installed on the computer.
Turn the ThinkLight
® on or off.
Note: This function is supported only on the ThinkPad Notebooks that have the ThinkLight.
The on or off status of the ThinkLight is shown on the screen for a few seconds when you press Fn+PgUp.
The computer display becomes brighter.
The computer display becomes dimmer.
Enable the FullScreen Magnifier function.
Have the same function as the SysRq key.
50
Hardware Maintenance Manual
Table 7. Fn key combinations (continued)
Key combination Description
Fn+ScrLk
Fn+Pause
Enable or disable the numeric keypad. The indicator of numeric lock will be displayed on the screen.
Have the same function as the Break key.
Fn+cursor keys These key combinations are for use with Windows Media Player. They have the following functions:
• Fn+down arrow key: Play or Pause
• Fn+up arrow key: Stop
• Fn+right arrow key: Next Track
• Fn+left arrow key: Previous Track
Chapter 6
.
Fn key combinations
51
52
Hardware Maintenance Manual
Chapter 7. FRU replacement notices
This chapter presents notices related to removing and replacing parts. Read this chapter carefully before replacing any FRU.
Screw notices
Loose screws can cause a reliability problem. In the ThinkPad Notebook, this problem is addressed with special nylon-coated screws that have the following characteristics:
• They maintain tight connections.
• They do not easily come loose, even with shock or vibration.
• They are harder to tighten.
• Each one should be used only once.
Do the following when you service this machine:
• Keep the screw kit (for the P/N, see “Miscellaneous parts” on page 138) in your tool bag.
• Always use new screws.
• Use a torque screwdriver if you have one.
Tighten screws as follows:
• Plastic to plastic
Turn an additional 90 degrees after the screw head touches the surface of the plastic part:
• Logic card to plastic
Turn an additional 180 degrees after the screw head touches the surface of the logic card:
• Torque driver
If you have a torque driver, refer to the “Torque” column for each step.
• Make sure that you use the correct screw. If you have a torque screwdriver, tighten all screws firmly to the torque shown in the table. Never use a screw that you removed. Use a new one. Make sure that all
of the screws are tightened firmly.
• Ensure torque screw drivers are calibrated correctly following country specifications.
© Copyright Lenovo 2011
53
Retaining serial numbers
This section includes the following descriptions:
•
“Restoring the serial number of the system unit” on page 54
•
“Retaining the UUID” on page 54
•
“Reading or writing the ECA information” on page 55
Restoring the serial number of the system unit
When the computer was manufactured, the EEPROM on the system board was loaded with the serial numbers of the system and all major components. These numbers need to remain the same throughout the life of the computer.
If you replace the system board, you must restore the serial number of the system unit to its original value.
Before replacing the system board, save the original serial number by doing the following:
1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the computer.
2. From the main menu, select 1. Set System Identification.
3. Select 2. Read S/N data from EEPROM.
The serial number of each device in your computer is displayed; the serial number of the system unit is listed as follows:
• 20: Serial number
Write down that number.
Note: The serial number of the system unit is also written on the label attached to the bottom of the computer.
After you have replaced the system board, restore the serial number by doing the following:
1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later and restart the computer.
2. From the main menu, select 1. Set System Identification.
3. Select 1. Add S/N data from EEPROM. Follow the instructions on the screen.
If the MTM and Product ID numbers differ from each other on the rear label, use what is shown for the
Product ID field. See example below:
MTM on rear label:
TTTT-CTO S/N SSSSSSS
Product ID on rear label:
TTTT-MMM (Use this number when setting Serial Number)
In the example, the Serial Number to be input is '1STTTTMMMSSSSSSS'.
Retaining the UUID
The Universally Unique Identifier (UUID) is a 128-bit number uniquely assigned to your computer at production and stored in the EEPROM of your system board.
54
Hardware Maintenance Manual
The algorithm that generates the number is designed to provide unique IDs until the year A.D. 3400. No two computers in the world have the same number.
When you replace the system board, you must set the UUID on the new system board as follows:
1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the computer.
2. From the main menu, select 4. Assign UUID. A new UUID is created and written. If a valid UUID already exists, it is not overwritten.
Reading or writing the ECA information
Information on Engineering Change Announcements (ECA) are stored in the EEPROM of the system board.
The electronic storage of this information simplifies the procedure to check if the ECA has been previously applied to a machine. The machine does not need to be disassembled to check for the ECA application.
To check what ECAs have been previously applied to the machine, use the ECA Information Read/Write function on the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later.
1. Insert the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the computer.
2. From the main menu, select 6. Set ECA Information.
3. To read ECA information, select 2. Read ECA/rework number from EEPROM and follow the instruction.
4. To read box build date, select 5. Read box build date from EEPROM, and follow the instruction on the screen.
After an ECA has been applied to the machine, the EEPROM must be updated to reflect the ECA's application. Use the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later to update the
EEPROM.
Note: Only the ECA number is stored in the EEPROM. The machine type of the ECA is assumed be the same
as the machine type of the machine that had the ECA applied to it.
1. Insert the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the computer.
2. From the main menu, select 6. Set ECA Information.
3. To write ECA information, select 1. Write ECA/rework number from EEPROM, and follow the instruction.
4. To write box build date, select 4. Write box build date from EEPROM, and follow the instruction on the screen.
If the system board is being replaced, try to read the ECA information from the old system board and transfer the information to the new system. If the system board is inoperable, this will not be possible.
Chapter 7
.
FRU replacement notices
55
56
Hardware Maintenance Manual
Chapter 8. Removing and replacing a FRU
This chapter presents directions and drawings for use in removing and replacing a FRU. Be sure to observe the following general rules:
1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts.
2. Before replacing any FRU, review Chapter 7 “FRU replacement notices” on page 53.
3. Begin by removing any FRUs that have to be removed before replacing the failing FRU. Such FRUs are listed in each FRU replacement section. Remove them in the order in which they are listed.
4. Follow the correct sequence in the steps for removing a FRU, as given in the drawings by the numbers in square callouts.
5. When turning a screw to replace a FRU, turn it in the direction as given by the arrow in the drawing.
6. When removing a FRU, move it in the direction as given by the arrow in the drawing.
7. To put the new FRU in place, reverse the removal procedure and follow any notes that pertain to
8. When replacing a FRU, use the correct screw(s) as shown in the procedures.
DANGER
Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables.
Attention: After replacing a FRU, do not turn on the computer until you have made sure that all screws,
springs, and other small parts are in place and none are loose inside the computer. Verify this by shaking the computer gently and listening for rattling sounds. Metallic parts or metal flakes can cause electrical short circuits.
Attention: The system board is sensitive to, and can be damaged by, electrostatic discharge. Before
touching it, establish personal grounding by touching a ground point with one hand or by using an electrostatic discharge (ESD) strap (P/N 6405959).
1010 Battery pack
Important notice for replacing a battery pack:
• Lenovo ThinkVantage Toolbox has an automatic battery diagnostic that determines if the battery pack is defective.
A battery pack FRU should not be replaced unless this diagnostic shows that the battery is defective.
• The only exception to this is if the battery pack is physically damaged or a customer is reporting a possible safety issue.
• If Lenovo ThinkVantage Toolbox is not installed in the computer, the customer should download this program before a non-physically damaged battery pack is replaced. Note that a physically damaged battery pack is a non-warranty replacement part.
Removal steps of battery pack
DANGER
Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode.
© Copyright Lenovo 2011
57
Unlock the battery latch
1
. Holding the battery lock lever in the unlocked position
2
, remove the battery pack in the direction shown by arrow
3
.
1 2
3
When installing: Install the battery pack along the slide rails of the slot. Make sure that the battery release
lever is in the locked position.
1020 ExpressCard blank bezel and Media Card blank bezel
Removal steps of ExpressCard blank bezel
When you press the ExpressCard blank bezel
1
, it pops out
2
.
1
2
58
Hardware Maintenance Manual
When installing: Make sure that the bezel is correctly oriented as shown in the following figure.
Removal steps of Media Card blank bezel
When you press the Media Card blank bezel
1
, it pops out
2
.
2
1
When installing: Make sure that the bezel is correctly oriented as shown in the following figure.
Chapter 8
.
Removing and replacing a FRU
59
1030 Optical drive or travel cover
For access, remove this FRU:
•
“1010 Battery pack” on page 57
Removal steps of optical drive or travel cover
1
Step
1
Screw (quantity)
M2 × 8 mm, flat-head, nylon-coated (1)
Color
Black
Torque
0.181 Nm
(1.85 kgfcm)
60
Hardware Maintenance Manual
3
2
1040 Thermal cover
For access, remove this FRU:
•
“1010 Battery pack” on page 57
Removal steps of thermal cover
Note: Loosen the screws
1
, but do not remove them.
1
1
1
1
1
1
Chapter 8
.
Removing and replacing a FRU
61
2
Attention: Do not touch or apply any excessive force to the fan motor located in the slot. It might cause
damage to the fan assembly or might cause the computer to malfunction.
1050 Hard disk drive or solid state drive assembly
For access, remove these FRUs in order:
•
“1010 Battery pack” on page 57
•
“1040 Thermal cover” on page 61
Attention:
• Do not drop the drive or apply any physical shock to it. The drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data.
• Before removing the drive, have the user make a backup copy of all the information on it if possible.
• Never remove the drive while the computer is operating or is in suspend mode.
Removal steps of HDD or SSD assembly
1
62
Hardware Maintenance Manual
When installing: Make sure that the HDD or SSD connector is attached firmly.
When installing:
• Do not apply excessive force to the HDD or SSD bracket
a
. To do so, you might bend or break it.
• Before installing an HDD or SSD assembly into models with only an mSATA solid state drive, be sure to remove the mSATA spacer
b
as shown in the following illustration.
b
Chapter 8
.
Removing and replacing a FRU
63
Removal steps of HDD or SSD bracket
1
1
2
1
1
Step
1
Screw (quantity)
M3 × 3.5 mm, flat-head (4)
1060 DIMM
For access, remove these FRUs in order:
•
“1010 Battery pack” on page 57
•
“1040 Thermal cover” on page 61
Color
Silver
Torque
0.392 Nm
(4 kgfcm)
64
Hardware Maintenance Manual
Removal steps of DIMM
1
1
2
Note: If only one DIMM is used on the computer you are servicing, the card must be installed in SLOT-0
(
a
: lower slot), but not in SLOT-1 (
b
: upper slot).
b a
When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it
until it snaps into place. Make sure that it is firmly fixed in the slot and does not move easily.
1070 Fan assembly
For access, remove these FRUs in order:
•
“1010 Battery pack” on page 57
•
“1040 Thermal cover” on page 61
Attention:
• Do not handle the fan roughly. Improper handling of the fan can cause distortion or deformation and imperfect contact with components.
• Do not touch or apply any excessive force to the fan motor. It might cause damage to the fan assembly or might cause the computer to malfunction.
Chapter 8
.
Removing and replacing a FRU
65
Table 8. Removal steps of fan assembly
1
When installing: Make sure that the fan connector is attached firmly to the system board.
Note: Loosen the screws
2a
to
2d
in order, but do not remove them. When you attach the fan, secure the screws in order.
2a
2d
2c
2b
Note: Different models might have different numbers of screws in step
2
.
66
Hardware Maintenance Manual
Table 8. Removal steps of fan assembly (continued)
3
When installing: Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2
grams, on the parts marked
a
as in the following figures. Either too much or too less application of grease can cause a thermal problem due to imperfect contact with a component. For the new CPU thermal device, you need to peel the thin film off from the rubbers marked
b
.
For models with a discrete fan assembly:
For models with an integrated fan assembly: a b
Chapter 8
.
Removing and replacing a FRU
67
Table 8. Removal steps of fan assembly (continued)
b
1080 CPU
For access, remove these FRUs in order:
•
“1010 Battery pack” on page 57
•
“1040 Thermal cover” on page 61
•
“1070 Fan assembly” on page 65
Attention: The CPU is extremely sensitive. When you service the CPU, avoid any kind of rough handling.
Removal steps of CPU
Rotate the head of the screw in the direction shown by arrow
1
to release the lock; then remove the CPU
2
.
1
2 a
68
Hardware Maintenance Manual
When installing: Place the CPU above the CPU socket, and then rotate the head of the screw in the
direction shown by arrow
a
to secure the CPU.
1090 SIM slot cover
For access, remove this FRU:
•
“1010 Battery pack” on page 57
Removal steps of SIM slot cover
Note: Loosen the screw
1
, but do not remove it.
1
2
Some models you are servicing might have the SIM card that the customer has installed.
If the computer you are servicing has the SIM card, remove it before you start the servicing.
After you finish the servicing, make sure that you insert the card back into the slot firmly.
Chapter 8
.
Removing and replacing a FRU
69
3
4
5
1110 Wireless WAN slot cover and PCI Express Mini Card for wireless
WAN
For access, remove this FRU:
•
“1010 Battery pack” on page 57
Removal steps of wireless WAN slot cover and PCI Express Mini Card for wireless WAN
Note: Loosen the screw
1
, but do not remove it.
1
70
Hardware Maintenance Manual
2
In steps
3a
and
3b
, unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in the direction of the arrows.
4
3a
3b
4
When installing: Plug the red cable into the jack labeled MAIN, and the blue cable into the jack labeled
AUX on the card.
Step
4
Screw (quantity)
M2 × 3 mm, flat-head, nylon-coated (2)
Color
Black
Torque
0.181 Nm
(1.85 kgfcm)
1110 mSATA solid state drive
For access, remove this FRU:
5
Chapter 8
.
Removing and replacing a FRU
71
•
“1010 Battery pack” on page 57
Attention:
• Do not drop the drive or apply any physical shock to it. The drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data.
• Before removing the drive, have the user make a backup copy of all the information on it if possible.
• Never remove the drive while the computer is operating or is in suspend mode.
Removal steps of mSATA solid state drive
Note: Loosen the screw
1
, but do not remove it.
1
2
72
Hardware Maintenance Manual
3
Step
3
Screw (quantity)
M2 × 3 mm, flat-head, nylon-coated (1)
1120 Palm rest assembly with cables
For access, remove these FRUs in order:
•
“1010 Battery pack” on page 57
•
“1030 Optical drive or travel cover” on page 60
4
Color
Black
Torque
0.181 Nm
(1.85 kgfcm)
Chapter 8
.
Removing and replacing a FRU
73
Removal steps of palm rest assembly with cables
2
2
1
2
2
2
1
2
2
When installing: Make sure all the screws have been fastened to secure the palm rest.
Step
1
Screw (quantity)
M2 × 8 mm, flat-head, nylon-coated (1)
Color
Black
2
M2 × 5 mm, flat-head, nylon-coated (6) Black
Torque
0.181 Nm
(1.85 kgfcm)
0.181 Nm
(1.85 kgfcm)
74
Hardware Maintenance Manual
3
4
3
When installing: Attach the palm rest so that the two small projections of the palm rest
a
firmly fit into the guide holes of the keyboard bezel, and them press the front side of the palm rest downward until it clicks into place. Refer to the following two figures.
a a
Chapter 8
.
Removing and replacing a FRU
75
Note: In models with the fingerprint reader, the sensor is attached to the palm rest FRU. If the fingerprint
reader is defective, you can remove the fingerprint reader by referring to step
8
as shown in the following figure.
7
6
5
7
6
8
When installing: Make sure that all the cables are attached firmly to the system board.
1130 PCI Express Mini Card for wireless LAN
For access, remove these FRUs in order:
•
“1010 Battery pack” on page 57
76
Hardware Maintenance Manual
•
“1030 Optical drive or travel cover” on page 60
•
“1120 Palm rest assembly with cables” on page 73
Removal steps of PCI Express Mini Card for wireless LAN
In step
1a
and
1b
, unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in the direction of the arrows.
1a
2
1b
2
Step
2
Screw (quantity)
M2 × 3 mm, flat-head, nylon-coated (2)
3
Color
Black
Torque
0.181 Nm
(1.85 kgfcm)
Chapter 8
.
Removing and replacing a FRU
77
When installing: Plug the gray cable into the jack labeled MAIN, and the black cable into the jack labeled
AUX on the card.
1140 Backup battery
For access, remove these FRUs in order:
•
“1010 Battery pack” on page 57
•
“1030 Optical drive or travel cover” on page 60
•
“1120 Palm rest assembly with cables” on page 73
Removal steps of backup battery
DANGER
Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode.
1
2
When installing: Make sure that the battery connector is attached firmly to the system board.
1150 Bluetooth daughter card
For access, remove these FRUs in order:
•
“1010 Battery pack” on page 57
•
“1030 Optical drive or travel cover” on page 60
•
“1120 Palm rest assembly with cables” on page 73
78
Hardware Maintenance Manual
Removal steps of Bluetooth daughter card
Step
1
Screw (quantity)
M2 × 3 mm, flat-head, nylon-coated (1)
Color
Black
Torque
0.181 Nm
(1.85 kgfcm)
When installing: Make sure that the connector on bottom side of the card is attached firmly to the system
board.
1160 Media Card Reader slot board and Media Card Reader cable assembly
For access, remove these FRUs in order:
•
“1010 Battery pack” on page 57
•
“1020 ExpressCard blank bezel and Media Card blank bezel” on page 58
•
“1030 Optical drive or travel cover” on page 60
•
“1090 SIM slot cover” on page 69
•
“1120 Palm rest assembly with cables” on page 73
Chapter 8
.
Removing and replacing a FRU
79
Removal steps of Media Card Reader slot board and Media Card Reader cable assembly
1
1
When installing: Make sure that the Media Card Reader cable assembly is attached firmly to the system
board and the Media Card Reader slot board.
3
2
2
80
Hardware Maintenance Manual
Step
2
Screw (quantity)
M2 × 3 mm, flat-head, nylon-coated (2)
1170 Keyboard
For access, remove these FRUs in order:
•
“1010 Battery pack” on page 57
•
“1030 Optical drive or travel cover” on page 60
•
“1120 Palm rest assembly with cables” on page 73
Removal steps of keyboard
1
Color
Black
Torque
0.181 Nm
(1.85 kgfcm)
When installing: Make sure the screw has been fastened to secure to keyboard.
Step
1
Screw (quantity)
M2 × 5 mm, flat-head, nylon-coated (1)
Color
Black
Torque
0.181 Nm
(1.85 kgfcm)
Chapter 8
.
Removing and replacing a FRU
81
6
7
3
2
2
4
5
When installing: Make sure all the connectors are attached firmly to the system board.
Step
6
7
Screw (quantity)
M2 × 3 mm, flat-head, nylon-coated (1)
M2 × 2 mm, flat-head (1)
Color
Black
Silver
Torque
0.181 Nm
(1.85 kgfcm)
0.181 Nm
(1.85 kgfcm)
8
When installing: Attach the keyboard so that the keyboard edges are under the frame as shown in the
following figure. To make sure that the front side of the keyboard is housed firmly, gently press the keys with your palms and slightly slide the keyboard toward you until it snaps into position.
82
Hardware Maintenance Manual
1180 Keyboard bezel
For access, remove these FRUs in order:
•
“1010 Battery pack” on page 57
•
“1030 Optical drive or travel cover” on page 60
•
“1070 Fan assembly” on page 65
•
“1110 Wireless WAN slot cover and PCI Express Mini Card for wireless WAN” on page 70
•
“1110 mSATA solid state drive” on page 71
•
“1120 Palm rest assembly with cables” on page 73
•
“1130 PCI Express Mini Card for wireless LAN” on page 76
•
Removal steps of keyboard bezel
Note: Steps
2a
and
3a
are only for ThinkPad L520 models. For ThinkPad L420 and L421 models, skip steps
2a
and
3a
.
1
3
3
2
2
2a
2a
2
1
3a
3
Chapter 8
.
Removing and replacing a FRU
83
Step
1
3
3a
2
2a
Screw (quantity)
M2.5 × 6.5 mm, flat-head, nylon-coated (2)
M2 × 3 mm, flat-head, nylon-coated (3)
M2 × 3 mm, flat-head, nylon-coated (2)
M2 × 5 mm, flat-head, nylon-coated (3)
M2 × 5 mm, flat-head, nylon-coated (1)
4
5
6
7
4
5
6
Color
Black
Black
Black
Black
Black
Torque
0.392 Nm
(4 kgfcm)
0.181 Nm
(1.85 kgfcm)
0.181 Nm
(1.85 kgfcm)
0.181 Nm
(1.85 kgfcm)
0.181 Nm
(1.85 kgfcm)
Step
4
Screw (quantity)
M2 × 3 mm, flat-head, nylon-coated (2)
Color
Black
Torque
0.181 Nm
(1.85 kgfcm)
When installing: Make sure that the connectors are attached firmly to the system board.
84
Hardware Maintenance Manual
8
8
1190 LCD unit
For access, remove these FRUs in order:
•
“1010 Battery pack” on page 57
•
“1030 Optical drive or travel cover” on page 60
•
“1110 Wireless WAN slot cover and PCI Express Mini Card for wireless WAN” on page 70
•
“1110 mSATA solid state drive” on page 71
•
“1120 Palm rest assembly with cables” on page 73
•
“1130 PCI Express Mini Card for wireless LAN” on page 76
•
•
“1180 Keyboard bezel” on page 83
Removal steps of LCD unit
Step
1
Screw (quantity)
M2.5 × 6.5 mm, flat-head, nylon-coated (2)
1
1
Color
Black
Torque
0.392 Nm
(4 kgfcm)
Chapter 8
.
Removing and replacing a FRU
85
2
2
3
When installing: Make sure that the connectors are attached firmly to the system board.
In step
4
, release wireless antenna cables from the cable guides.
For ThinkPad L520 models:
4
4
4
4
4
4
4
4
4
4
4
For ThinkPad L420 and L421 models:
86
Hardware Maintenance Manual
4
4
4 4
4
4
4
4
4
4
4
4
4
4
4
4
4
When installing: Make sure that the cables are attached to the cable guides firmly.
Attention: When you route the cables, make sure that they are not subjected to any tension. Tension could
cause the cables to be damaged by the cable guides, or a wire to be broken.
5
5
Step
5
Screw (quantity)
M2.5 × 6.5 mm, flat-head, nylon-coated (4)
5
5
Color
Black
Torque
0.392 Nm
(4 kgfcm)
Chapter 8
.
Removing and replacing a FRU
87
6
6
2010 Top shielding assembly
For access, remove these FRUs in order:
•
“1010 Battery pack” on page 57
•
“1030 Optical drive or travel cover” on page 60
•
“1110 Wireless WAN slot cover and PCI Express Mini Card for wireless WAN” on page 70
•
“1110 mSATA solid state drive” on page 71
•
“1120 Palm rest assembly with cables” on page 73
•
“1130 PCI Express Mini Card for wireless LAN” on page 76
•
•
“1180 Keyboard bezel” on page 83
•
Removal steps of top shielding assembly
For ThinkPad L520 models:
88
Hardware Maintenance Manual
1
2
2
2
1
1
2
2
3
Step
1
2
Screw (quantity)
M2 × 3 mm, flat-headd, nylon-coated (3)
M2 × 5 mm, flat-head, nylon-coated (5)
For ThinkPad L420 and L421 models:
1
1
2
2
2
3
Color
Black
Black
Torque
0.181 Nm
(1.85 kgfcm)
0.181 Nm
(1.85 kgfcm)
Step
1
2
Screw (quantity)
M2 × 3 mm, flat-head, nylon-coated (2)
M2 × 5 mm, flat-head, nylon-coated (3)
Color
Black
Black
Torque
0.181 Nm
(1.85 kgfcm)
0.181 Nm
(1.85 kgfcm)
Chapter 8
.
Removing and replacing a FRU
89
2020 System board assembly
Important notices for handling the system board:
When handling the system board, bear the following in mind.
• The system board has an accelerometer, which can be broken by applying several thousands of G-forces.
Note: Dropping a system board from a height of as little as 6 inches so that it falls flat on a hard bench can subject the accelerometer to as much as 6,000 G's of shock.
• Be careful not to drop the system board on a bench top that has a hard surface, such as metal, wood, or composite.
• If a system board is dropped, you must test it, using PC-Doctor for DOS, to make sure that the HDD Active
Protection System™ still functions.
Note: If the test shows that the HDD Active Protection System is not functioning, be sure to document the drop in any reject report, and replace the system board.
• Avoid rough handling of any kind.
• At every point in the process, be sure not to drop or stack the system board.
• If you put a system board down, be sure to put it only on a padded surface such as an ESD mat or a corrugated conductive surface.
After replacing the system board, run PC-Doctor for DOS to make sure that the HDD Active Protection System still functions. The procedure is as follows:
1. Place the computer on a horizontal surface.
2. Run Diagnostics ➙ ThinkPad Devices ➙ HDD Active Protection Test.
Attention: Do not apply physical shock to the computer while the test is running.
For access, remove these FRUs in order:
•
“1010 Battery pack” on page 57
•
“1020 ExpressCard blank bezel and Media Card blank bezel” on page 58
•
“1030 Optical drive or travel cover” on page 60
•
“1040 Thermal cover” on page 61
•
“1050 Hard disk drive or solid state drive assembly” on page 62
•
•
“1070 Fan assembly” on page 65
•
•
“1090 SIM slot cover” on page 69
•
“1110 Wireless WAN slot cover and PCI Express Mini Card for wireless WAN” on page 70
•
“1110 mSATA solid state drive” on page 71
•
“1120 Palm rest assembly with cables” on page 73
•
“1130 PCI Express Mini Card for wireless LAN” on page 76
•
“1140 Backup battery” on page 78
•
“1150 Bluetooth daughter card ” on page 78
•
“1160 Media Card Reader slot board and Media Card Reader cable assembly” on page 79
•
•
“1180 Keyboard bezel” on page 83
•
•
“2010 Top shielding assembly” on page 88
Location of major sensitive components on the system board in ThinkPad L420, L421, and L520 models
The following components soldered on the top side of the system board are extremely sensitive. When you service the system board, avoid any kind of rough handling.
a
Accelerometer chip for the HDD Active Protection System
90
Hardware Maintenance Manual
b c d
Multi Chip Package (MCP) processor
Video chip (only for discrete models)
Platform Controller Hub (PCH)
For ThinkPad L420 and L421 models with an integrated thermal module (top side view):
a
For ThinkPad L420 and L421 models with an integrated thermal module (bottom side view):
b d
For ThinkPad L520 models with an integrated thermal module (top side view):
a
Chapter 8
.
Removing and replacing a FRU
91
For ThinkPad L520 models with an integrated thermal module (bottom side view):
b d
For ThinkPad L420 and L421 models with a discrete thermal module (top side view):
a
For ThinkPad L420 and L421 models with a discrete thermal module (bottom side view):
b c d
For ThinkPad L520 models with a discrete thermal module (top side view):
92
Hardware Maintenance Manual
a
For ThinkPad L520 models with a discrete thermal module (bottom side view):
b c d
Removal steps of system board assembly
For ThinkPad L520 models:
1
1
1
1
Step
1
Screw (quantity)
M2 × 5 mm, flat-head, nylon-coated (4)
Color
Black
Torque
0.181 Nm
(1.85 kgfcm)
Chapter 8
.
Removing and replacing a FRU
93
For ThinkPad L420 and L421 models:
1
1
Step
1
Screw (quantity)
M2 × 5 mm, flat-head, nylon-coated (2)
For ThinkPad L520 models:
2
2
Color
Black
Torque
0.181 Nm
(1.85 kgfcm)
3
For ThinkPad L420 and L421 models:
94
Hardware Maintenance Manual
2
2
3
When installing: Make sure that the connectors are attached firmly to the system board.
2030 USB connector board and USB cable assembly
For access, remove these FRUs in order:
•
“1010 Battery pack” on page 57
•
“1040 Thermal cover” on page 61
•
“1050 Hard disk drive or solid state drive assembly” on page 62
•
“1110 Wireless WAN slot cover and PCI Express Mini Card for wireless WAN” on page 70
•
“1110 mSATA solid state drive” on page 71
•
“1120 Palm rest assembly with cables” on page 73
•
“1130 PCI Express Mini Card for wireless LAN” on page 76
•
“1160 Media Card Reader slot board and Media Card Reader cable assembly” on page 79
•
•
“1180 Keyboard bezel” on page 83
•
•
“2010 Top shielding assembly” on page 88
Chapter 8
.
Removing and replacing a FRU
95
Removal steps of USB connector board and USB cable assembly
2
1 4
3
When installing: Make sure that the connectors are attached firmly.
Step
2
Screw (quantity)
M2 × 3 mm, flat-head, nylon-coated (1)
Color
Black
Cable routing: Route the USB cable assembly as shown in the following figures.
For ThinkPad L520 models:
Torque
0.181 Nm
(1.85 kgfcm)
For ThinkPad L420 and L421 models:
96
Hardware Maintenance Manual
2040 DC-in cable and base cover
For access, remove these FRUs in order:
•
“1010 Battery pack” on page 57
•
“1020 ExpressCard blank bezel and Media Card blank bezel” on page 58
•
“1030 Optical drive or travel cover” on page 60
•
“1040 Thermal cover” on page 61
•
“1050 Hard disk drive or solid state drive assembly” on page 62
•
•
“1070 Fan assembly” on page 65
•
“1110 Wireless WAN slot cover and PCI Express Mini Card for wireless WAN” on page 70
•
“1110 mSATA solid state drive” on page 71
•
“1120 Palm rest assembly with cables” on page 73
•
“1130 PCI Express Mini Card for wireless LAN” on page 76
•
“1160 Media Card Reader slot board and Media Card Reader cable assembly” on page 79
•
•
“1180 Keyboard bezel” on page 83
•
•
“2010 Top shielding assembly” on page 88
•
“2020 System board assembly” on page 90
Removal steps of DC-in cable and base cover
For ThinkPad L520 models:
Chapter 8
.
Removing and replacing a FRU
97
2
1
1
3
Step
1
Screw (quantity)
M2 × 3 mm, flat-head, nylon-coated (2)
For ThinkPad L420 and L421 models:
Color
Black
Torque
0.181 Nm
(1.85 kgfcm)
2
1
3
Step
1
Screw (quantity)
M2 × 5 mm, flat-head, nylon-coated (1)
Cable routing: Route the cable as shown in the following figures.
For ThinkPad L520 models:
Color
Black
Torque
0.181 Nm
(1.85 kgfcm)
98
Hardware Maintenance Manual
For ThinkPad L420 and L421 models:
Applying labels to the base cover
The new base cover FRU is shipped with a kit containing labels of several kinds.
If the Windows Certificate of Authentication label (COA)
3
is attached to a part that is replaced, return the old part with the label attached to the customer, or provide a letter to the customer stating what the label was originally on the system and what the label part number, serial number, and product key were.
When you replace the base cover, apply the following labels:
4
Battery word label
6
Homologation label
The following labels need to be peeled off from the old base cover, and need to be put on the new base cover.
1
MAC address label
2
Wireless WAN MAC address label
5
Non-Encryption label or Indonesia rating label
7
Serial number label
8
FCC label
9
SIM ICC ID label
10
Indonesia postel label or Brazil Anatel BG label
11
SIRIM label or Brazil Anatel Bluetooth label
12
Israel label (SIM models)
13
Product label
For some models, you need to apply two FCC labels. Check the old base cover; if it has two FCC labels, apply both to the new base cover.
Chapter 8
.
Removing and replacing a FRU
99
For the location of each label, refer to the following figures:
For ThinkPad L520 models:
1 2 3 4
13
12
11
10
5
6
7
8
9
For ThinkPad L420 and L421 models:
1 2 3 4
13
12
11
10
5
6
7
8
9
2050 LCD front bezel
For access, remove these FRUs in order:
•
“1010 Battery pack” on page 57
•
“1110 Wireless WAN slot cover and PCI Express Mini Card for wireless WAN” on page 70
•
“1110 mSATA solid state drive” on page 71
•
“1120 Palm rest assembly with cables” on page 73
•
“1130 PCI Express Mini Card for wireless LAN” on page 76
•
•
“1180 Keyboard bezel” on page 83
•
100
Hardware Maintenance Manual
Removal steps of LCD front bezel
1
1
1
1
Step
1
Screw cap Screw (quantity)
M2 × 5 mm, flat-head, nylon-coated (4)
2
2
2
2
2
2
Color
Black
2
2
2
2
2
Torque
0.181 Nm
(1.85 kgfcm)
When installing: Make sure that all the latches are attached firmly. Then secure the bezel with the screws.
2060 Speaker assembly
For access, remove these FRUs in order:
•
“1010 Battery pack” on page 57
•
“1110 Wireless WAN slot cover and PCI Express Mini Card for wireless WAN” on page 70
•
“1110 mSATA solid state drive” on page 71
•
“1120 Palm rest assembly with cables” on page 73
•
“1130 PCI Express Mini Card for wireless LAN” on page 76
•
•
“1180 Keyboard bezel” on page 83
•
•
“2050 LCD front bezel” on page 100
Chapter 8
.
Removing and replacing a FRU
101
Removal steps of speaker assembly
1
3
1
2
Step
1
Screw (quantity)
M2 × 3 mm, flat-head, nylon-coated (2)
Color
Black
Torque
0.181 Nm
(1.85 kgfcm)
2070 Integrated camera
For access, remove these FRUs in order:
•
“1010 Battery pack” on page 57
•
“1110 Wireless WAN slot cover and PCI Express Mini Card for wireless WAN” on page 70
•
“1110 mSATA solid state drive” on page 71
•
“1120 Palm rest assembly with cables” on page 73
•
“1130 PCI Express Mini Card for wireless LAN” on page 76
•
•
“1180 Keyboard bezel” on page 83
•
•
“2050 LCD front bezel” on page 100
•
“2060 Speaker assembly” on page 101
102
Hardware Maintenance Manual
Removal steps of integrated camera
1
3
2
1
Step
1
Screw (quantity)
M2 × 3 mm, flat-head, nylon-coated (2)
Color
Black
Torque
0.181 Nm
(1.85 kgfcm)
When installing: Make sure that the connector is attached firmly.
2080 Antenna assembly
For access, remove these FRUs in order:
•
“1010 Battery pack” on page 57
•
“1110 Wireless WAN slot cover and PCI Express Mini Card for wireless WAN” on page 70
•
“1110 mSATA solid state drive” on page 71
•
“1120 Palm rest assembly with cables” on page 73
•
“1130 PCI Express Mini Card for wireless LAN” on page 76
•
•
“1180 Keyboard bezel” on page 83
•
•
“2050 LCD front bezel” on page 100
•
“2060 Speaker assembly” on page 101
•
“2070 Integrated camera” on page 102
Removal steps of antenna assembly
Release the antenna cables from the cable guides of the LCD rear cover assembly and from the hinges.
For ThinkPad L520 models:
Chapter 8
.
Removing and replacing a FRU
103
1
1
1
For ThinkPad L420 and L421 models:
1
1 1
1
1
1
1
1
1
When installing: Route the cables as shown in the following figure. When you route the cables, make sure
that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken.
104
Hardware Maintenance Manual
2
2
2
2
2
2090 Hinges, LCD panel, LCD cable, and LCD rear cover assembly
For access, remove these FRUs in order:
•
“1010 Battery pack” on page 57
•
“1110 Wireless WAN slot cover and PCI Express Mini Card for wireless WAN” on page 70
•
“1110 mSATA solid state drive” on page 71
•
“1120 Palm rest assembly with cables” on page 73
•
“1130 PCI Express Mini Card for wireless LAN” on page 76
•
•
“1180 Keyboard bezel” on page 83
•
•
“2050 LCD front bezel” on page 100
•
“2060 Speaker assembly” on page 101
•
“2070 Integrated camera” on page 102
•
“2080 Antenna assembly” on page 103
Removal steps of hinges, LCD panel, LCD cable, and LCD rear cover assembly
For ThinkPad L520 models:
1
1
1
1
Chapter 8
.
Removing and replacing a FRU
105
Step
1
Screw (quantity)
M2 × 5 mm, flat-head, nylon-coated (4)
For ThinkPad L420 and L421 models:
1
Color
Black
Torque
0.181 Nm
(1.85 kgfcm)
1
Step
1
Screw (quantity)
M2 × 5 mm, flat-head, nylon-coated (2)
Color
Black
Torque
0.181 Nm
(1.85 kgfcm)
2
106
Hardware Maintenance Manual
3
4
3
Step
3
Screw (quantity)
M2 × 3 mm, flat-head, nylon-coated (4)
5
6
7
4
3
Color
Black
3
Torque
0.181 Nm
(1.85 kgfcm)
When installing: Make sure that the LCD connector is attached firmly.
Chapter 8
.
Removing and replacing a FRU
107
108
Hardware Maintenance Manual
Chapter 9. Locations
This chapter presents the locations of ThinkPad L420, L421, and L520 hardware components.
Front view
1
2
3
19
3
17
16
18
15
14
13
12
11
10
9
8
7
6
5
4
1
Integrated camera
2
Built-in microphone
3
Built-in stereo speakers
4
Power switch
5
ac power connector
6
ThinkVantage button
7
System status indicators
2
8
Optical drive, second battery, or travel cover
9
Media Card reader
10
USB connectors
11
Wireless radio switch
12
Power status indicators
1
13
Fingerprint reader (for some models)
14
Touch pad buttons
15
Touch pad
16
TrackPoint buttons
17
TrackPoint pointing stick
18
UltraNav
19
Volume control buttons
1
: For the description of each power status indicator, see Chapter 5 “Status indicators” on page 47.
2
: For the description of each system status indicator, see Chapter 5 “Status indicators” on page 47.
© Copyright Lenovo 2011
109
Rear view
7
6
5
4
3
2
1
1
Combo audio jack
2
DisplayPort connector
3
eSATA/USB combo connector
4
RJ-45 (Ethernet) connector
5
External monitor connector
6
Security keyhole
1
7
Always On USB connector
1
: In some models, the security keyhole is located on the right side of the computer.
Bottom view
1
2
3
6
4
5
1
Battery pack
2
Battery pack latch
3
Docking connector (for some models)
4
Thermal slot cover
1
5
ExpressCard slot
6
Wireless WAN card slot
7
SIM slot
1
: The DIMM, hard disk drive, and thermal module are located underneath the thermal slot cover.
110
Hardware Maintenance Manual
Chapter 10. Parts list
This chapter contains following lists of the service parts.
•
•
•
•
“Miscellaneous parts” on page 138
•
“ac power adapters” on page 140
•
•
•
“Common service tools” on page 149
Notes:
• Each FRU is available for all types or models, unless specific types or models are specified.
• FRU with specific models listed and described as xxU (where U is an example of a country designator) should be used for all models ending in U.
• FRU with specific models listed and described as 3Dx (where 3D is an example of a unique configuration) should be used for all of these models, unless specific country or region designator is specified.
• A CRU (customer replaceable unit) is identified by a single asterisk (*) or two asterisks (**) in the CRU ID column. An
N in the CRU ID column means that the part is not a CRU. A single asterisk (*) means that the part is a Self-service
CRU; two asterisks (**) means that the part is an Optional-service CRU.
External CRU statement to customers:
Some problems with your product can be resolved with a replacement part you can install yourself, called a “Customer Replaceable Unit” or “CRU.” Some CRUs are designated as Self-service CRUs and others are designated as Optional-service CRUs. Installation of Self-service CRUs is your responsibility; you may request that Lenovo installs an Optional-service CRU according to the warranty service for your product. Where you are installing the CRU, Lenovo will ship the CRU to you. CRU information and replacement instructions are shipped with your product and are available from Lenovo at any time upon request. You may find a list of CRUs in the publications that ship with your product or at http://www.lenovo.com/CRUs. You may be required to return the defective part that is replaced by the CRU. When return is required: (1) return instructions, a prepaid shipping label, and a container will be included with the replacement CRU; and (2) you may be charged for the replacement CRU if
Lenovo does not receive the defective part within thirty (30) days of your receipt of the replacement CRU. See your
Lenovo Limited Warranty documentation for full details.
ThinkPad computers contain the following types of CRUs:
– Self-service CRUs: These CRUs unplug or are held by no more than two screws. Examples of these types of CRUs include the ac power adapter, power cord, battery, and hard disk drive. Other Self-service CRUs depending on product design may include the memory module, wireless card, keyboard, and palm rest with finger print reader and touchpad.
– Optional-service CRUs: These CRUs are isolated parts within the computer that are concealed by an access panel that is typically secured by more than two screws. Once the access panel is removed, the specific
CRU is visible.
© Copyright Lenovo 2011
111
• FRUs marked with
OP
are available as options.
Overall
29
28
16
15
21
20
19
18
17
25
24
23
22
27
26
14
13
112
Hardware Maintenance Manual
1
2
3
4
5
6
7
8
9
10
11
12
Table 9. Parts list—Overall
No. FRU (Overall) FRU no.
CRU
ID
1
LCD unit (see “LCD FRUs” on page 132.)
2 Keyboard bezel assembly for 14W
2 Keyboard bezel assembly for 15W
3
Top shielding assembly for 14W Dock
3 Top shielding assembly for 15W Dock
4 1-GB DDR3-1333 SDRAM SO-DIMM (PC3-10600) card
• 7826-CTO, 32x, 33x
• 7827-CTO, 4Ax, 4Bx, 4Gx
• 7829-CTO, 4Bx
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO, 32x, 42x, 43x, 48x, 49x, 4Ex
• 5017-CTO, 32x, 42x, 43x, 48x, 49x, 4Ax
• 5019-CTO
• 7859-CTO, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx
• 7860-CTO, 39x
4 2-GB DDR3-1333 SDRAM SO-DIMM (PC3-10600) card
• 7826-CTO, 34x, 35x, 36x, 37x, 38x, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx,
3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx, 42x, 43x, 44x, 45x, 46x,
47x, 48x
• 7827-CTO, 32x, 34x, 42x, 43x, 44x, 47x, 48x, 49x, 4Dx, 4Ex, 4Fx, 4Jx, 4Lx, 4Nx, 55x, 56x,
57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Px,
5Qx, 5Sx, 5Tx, 5Vx, 5Yx, 5Zx, 62x, 67x, 68x, 69x
• 7829-CTO, 32x, 34x, 42x, 43x, 44x, 47x, 48x, 49x, 4Ax, 4Dx, 4Ex, 4Fx, 4Lx, 4Mx, 4Qx,
4Rx, 4Sx, 4Tx, 4Ux, 4Yx, 4Zx
• 7853-CTO
• 7854-CTO, 3Ax, 3Bx, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux,
3Vx, 3Wx, 3Yx, 3Zx, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Lx, 4Mx,
4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Bx
• 7856-CTO, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Qx, 3Sx,
3Vx, 3Xx, 3Yx, 3Zx, 42x, 43x, 46x, 47x, 48x, 49x, 4Bx, 4Cx, 4Dx
• 5015-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx
• 5016-CTO, 32x, 42x, 43x, 45x, 46x, 48x, 49x, 4Bx, 4Cx, 4Dx, 4Ex, 4Gx, 4Hx, 4Jx, 4Lx,
5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Tx, 5Vx, 5Wx, 5Xx,
5Yx, 63x, 64x
• 5017-CTO, 32x, 42x, 43x, 45x, 46x, 48x, 49x, 4Ax, 4Ex, 4Fx, 4Gx, 4Mx, 4Nx, 4Px
• 5019-CTO
• 7859-CTO, 3Dx, 3Ex, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Xx, 3Yx,
42x, 43x, 4Fx, 4Gx, 4Hx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 53x, 54x, 55x,
56x, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Wx, 5Xx, 5Yx, 5Zx, 62x, 63x, 64x, 65x, 66x
• 7860-CTO, 39x, 3Bx, 3Cx, 3Dx, 3Fx, 3Gx, 3Hx, 3Jx, 3Lx, 3Mx, 3Px, 3Qx, 3Rx, 3Sx
04W1813
55Y3715
N
04W1814 N
04W1766 N
04W1767 N
**
55Y3716 **
Chapter 10
.
Parts list
113
Table 9. Parts list—Overall (continued)
No. FRU (Overall)
4 4-GB DDR3-1333 SDRAM SO-DIMM (PC3-10600) card
• 7826-CTO, 39x, 3Ax, 3Bx, 49x
• 7827-CTO, 33x, 45x, 46x, 4Cx, 4Hx, 4Kx, 4Mx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx,
4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 5Rx, 5Wx, 5Xx, 66x
• 7829-CTO, 33x, 45x, 46x, 4Cx, 4Gx, 4Hx, 4Jx, 4Kx, 4Nx, 4Px, 4Vx, 4Wx, 4Xx
• 7853-CTO
• 7854-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Cx, 3Dx, 3Ex, 3Fx, 3Xx, 42x, 43x, 44x,
45x, 46x, 4Jx, 4Kx, 4Ux, 4Vx, 4Wx, 5Ax, 5Cx, 5Dx, 5Ex
• 7856-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 3Nx, 3Px, 3Rx, 3Tx, 3Ux, 3Wx, 44x, 45x, 4Ax
• 5015-CTO
• 5016-CTO, 33x, 44x, 47x, 4Ax, 4Fx, 4Kx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx,
4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Sx, 5Zx, 62x
• 5017-CTO, 33x, 44x, 47x, 4Bx, 4Cx, 4Dx, 4Hx, 4Jx, 4Kx, 4Lx
• 5019-CTO
• 7859-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Fx, 3Gx, 3Hx, 3Jx,
3Wx, 3Zx, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Jx, 4Kx, 4Lx, 4Wx, 4Xx,
4Yx, 4Zx, 52x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Vx
• 7860-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 3Ax, 3Ex, 3Kx, 3Nx
5 Media Card Reader board assembly
6 Media Card Reader slot blank bezel
7
USB cable assembly for 14W
7 USB cable assembly for 15W
8 USB connector board assembly
9 DC-in cable for 14W
9
DC-in cable for 15W
10 Battery pack, 4 cell Li-ion (2.2 Ah)
• 7826-CTO, 34x, 3Fx, 3Gx, 44x
• 7827-CTO, 5Mx, 5Nx, 5Px, 67x, 68x
• 7829-CTO
• 7853-CTO
• 7854-CTO, 48x
• 7856-CTO
• 5015-CTO, 34x, 35x, 3Cx
• 5016-CTO, 5Px, 63x, 64x
• 5017-CTO
• 5019-CTO
• 7859-CTO, 5Jx
• 7860-CTO
10 Battery pack, 6 cell Li-ion (2.2 Ah)
• 7826-CTO, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 45x, 46x, 47x, 48x, 49x
• 7827-CTO, 4Cx, 4Dx, 4Ex, 4Fx, 5Ax, 5Bx
• 7829-CTO, 4Zx
• 7853-CTO
• 7854-CTO, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px,
3Qx, 3Xx, 3Yx, 3Zx, 4Gx, 4Hx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx
• 7856-CTO, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Wx
• 5015-CTO, 36x, 37x
• 5016-CTO, 4Fx, 4Gx, 4Hx, 4Jx, 5Lx, 5Mx
• 5017-CTO, 4Px
• 5019-CTO
FRU no.
CRU
ID
55Y3717 **
04W1743 N
04W1720 N
45M2861 N
45M2871 N
04W1744 N
45M2862 N
45M2863 N
42T4887
42T4883
42T4885
*
42T4921
42T4923
42T4925
42T4927
*
114
Hardware Maintenance Manual
Table 9. Parts list—Overall (continued)
No. FRU (Overall) FRU no.
CRU
ID
• 7859-CTO, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx,
3Tx, 3Zx, 42x, 43x, 4Fx, 4Gx, 4Hx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 5Gx, 5Hx,
5Kx, 5Lx, 5Mx, 5Nx, 5Wx, 5Xx, 5Yx, 5Zx, 62x, 63x, 64x, 65x, 66x
• 7860-CTO, 3Dx, 3Hx, 3Jx
10
Battery pack, 6 cell Li-ion (2.6 Ah)
• 7826-CTO, 32x, 33x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Rx, 3Sx, 3Tx,
3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx, 42x, 43x
• 7827-CTO, 32x, 33x, 34x, 42x, 43x, 44x, 47x, 48x, 49x, 4Ax, 4Bx, 4Gx, 4Hx, 4Jx, 4Kx,
4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x,
55x, 56x, 57x, 58x, 59x, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Qx, 5Rx, 5Sx, 5Tx,
5Vx, 5Wx, 5Xx, 5Yx, 5Zx, 62x, 66x, 69x
• 7829-CTO, 32x, 33x, 34x, 42x, 43x, 44x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx,
4Gx, 4Hx, 4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx
• 7853-CTO
• 7854-CTO, 36x, 37x, 38x, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 42x, 43x, 44x, 45x, 46x, 47x,
49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Jx, 4Kx, 4Lx, 4Mx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx,
52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex
• 7856-CTO, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Nx, 3Px, 3Qx, 3Sx, 3Vx,
3Xx, 3Yx, 3Zx, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx
• 5015-CTO, 32x, 33x, 38x, 39x, 3Ax, 3Bx
• 5016-CTO, 32x, 33x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx,
4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Ax, 5Bx,
5Cx, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 5Kx, 5Nx, 5Qx, 5Rx, 5Sx, 5Tx, 5Vx, 5Wx, 5Xx, 5Yx, 62x
• 5017-CTO, 32x, 33x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Lx,
4Mx, 4Nx
• 5019-CTO
• 7859-CTO, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 44x, 45x, 46x,
47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Jx, 4Kx, 4Lx, 4Mx, 4Wx, 4Xx, 4Yx, 4Zx, 52x,
53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Ax, 5Cx, 5Dx, 5Ex, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Vx
• 7860-CTO, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Ex, 3Fx, 3Gx, 3Kx, 3Lx, 3Mx, 3Nx,
3Px, 3Qx, 3Rx, 3Sx
10 Battery pack, 6 cell Li-ion (10.4 Wh)
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
42T4791
42T4793
42T4795
42T4911
42T4817
42T4819
*
*
Chapter 10
.
Parts list
115
Table 9. Parts list—Overall (continued)
No. FRU (Overall)
10 Battery pack, 9 cell Li-ion (2.8 Ah)
• 7826-CTO
• 7827-CTO, 45x, 46x
• 7829-CTO, 45x, 46x
• 7853-CTO
• 7854-CTO, 32x, 33x, 34x, 35x
• 7856-CTO, 32x, 33x, 34x, 35x, 3Rx, 3Tx, 3Ux
• 5015-CTO
• 5016-CTO, 42x, 43x, 44x, 45x, 46x, 47x, 4Kx, 5Zx
• 5017-CTO, 42x, 43x, 44x, 45x, 46x, 47x
• 5019-CTO
• 7859-CTO, 32x, 33x, 34x, 5Bx
• 7860-CTO, 32x, 33x, 34x
11 Base cover assembly for 14W Dock
• 7826-CTO, 32x, 36x, 3Dx, 3Ex, 3Zx
• 7827-CTO, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Ex, 4Fx, 4Gx, 4Hx, 4Nx,
4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 55x, 56x, 57x,
58x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Lx, 5Qx, 5Rx, 5Sx, 5Tx, 5Vx, 5Wx, 5Xx,
66x, 67x, 68x, 69x
• 7829-CTO, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Ex, 4Fx, 4Gx, 4Kx, 4Lx, 4Mx,
4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Wx, 4Xx, 4Yx
• 7853-CTO
• 7854-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 3Ax, 3Lx, 3Mx, 3Nx, 3Rx, 3Sx, 3Tx, 3Yx,
3Zx, 42x, 43x, 44x, 45x, 46x, 48x, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Lx, 4Mx, 4Px, 4Sx, 4Ux, 4Vx,
4Wx, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex
• 7856-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Mx, 3Nx, 3Px, 3Qx, 3Sx, 3Tx,
3Ux, 3Vx, 3Wx, 3Xx, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx
11 Base cover assembly for 14W Dock for Taiwan, 65 W
• 7826-CTO, 3Gx
• 7827-CTO, 32x, 33x, 34x, 5Mx
• 7829-CTO, 32x, 33x, 34x, 4Zx
• 7853-CTO
• 7854-CTO
• 7856-CTO, 3Lx
11 Base cover assembly for 14W Dock for Taiwan, 90 W
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
11
Base cover assembly for 15W Dock
• 5015-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx
• 5016-CTO, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx,
4Hx, 4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx,
52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 5Kx,
5Lx, 5Mx, 5Nx, 5Qx, 5Rx, 5Sx, 5Tx, 5Vx, 5Wx, 5Xx, 5Yx, 5Zx, 62x, 63x, 64x
• 5017-CTO, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx,
4Hx, 4Jx, 4Kx, 4Lx, 4Mx, 4Nx
• 5019-CTO
• 7859-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx,
3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx,
42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx,
4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x,
FRU no.
CRU
ID
* 42T4799
42T4801
42T4912
04W1737 N
04W1738 N
04W1739 N
04W1740 N
116
Hardware Maintenance Manual
Table 9. Parts list—Overall (continued)
No. FRU (Overall) FRU no.
CRU
ID
55x, 56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx,
5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Vx, 5Wx, 5Xx, 5Yx, 5Zx, 62x, 63x, 64x, 65x, 66x
• 7860-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx,
3Hx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx
11 Base cover assembly for 15W Dock for Taiwan, 65 W
• 5015-CTO
• 5016-CTO, 32x, 33x, 5Px
• 5017-CTO, 32x, 33x, 4Px
• 5019-CTO
• 7859-CTO
• 7860-CTO, 3Jx
12 DVD-RAM/RW drive
• 7826-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Ex, 3Fx, 3Gx, 3Hx,
3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx, 42x,
43x, 44x, 45x, 46x, 47x, 48x, 49x
• 7827-CTO, 32x, 33x, 34x, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex,
4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx,
4Yx, 4Zx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx,
5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Vx, 5Wx, 5Xx, 5Yx, 5Zx, 62x, 69x
• 7829-CTO, 32x, 33x, 34x, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx,
4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx,
4Xx, 4Yx, 4Zx
• 7853-CTO
• 7854-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx,
3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx,
42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx,
4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x,
55x, 56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex
• 7856-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx,
3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx,
42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx
• 5015-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 39x, 3Bx, 3Cx
• 5016-CTO, 32x, 33x, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx,
4Gx, 4Hx, 4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx,
4Zx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx,
5Kx, 5Lx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Xx, 5Zx
• 5017-CTO, 32x, 33x, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx,
4Gx, 4Hx, 4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px
• 5019-CTO
• 7859-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx,
3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx,
42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx,
4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x,
55x, 56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx,
5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Vx, 5Wx, 5Xx, 5Yx, 5Zx, 62x, 63x, 64x, 65x, 66x
• 7860-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx,
3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx
04W1741 N
04W1268
04W1269
04W1270
*
Chapter 10
.
Parts list
117
Table 9. Parts list—Overall (continued)
No. FRU (Overall)
12 DVD-ROM drive
• 7826-CTO, 3Dx
• 7827-CTO, 66x, 67x, 68x
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO, 38x, 3Ax
• 5016-CTO, 5Vx, 5Wx, 5Yx, 62x, 63x, 64x
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
12 Travel cover
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
13
SIM slot cover with screw
14 Wireless LAN card slot cover with screw for 14W
14 Wireless LAN card slot cover with screw for 15W
15 Thermal cover with screw for 14W Dock
15 Thermal cover with screw for 15W Dock
16 SATA hard disk drive, 160 GB, 7,200 rpm
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
118
Hardware Maintenance Manual
FRU no.
CRU
ID
04W1271 *
04W0359 *
60Y4187 *
60Y4185 *
60Y4191 *
04W1718 *
75Y4677 *
60Y4805
60Y4815
75Y5121
**
Table 9. Parts list—Overall (continued)
No. FRU (Overall)
16 SATA hard disk drive, 160 GB, 7,200 rpm, 7mmH
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
16 SATA hard disk drive, 250 GB, 5,400 rpm
• 7826-CTO, 3Zx, 44x
• 7827-CTO, 52x, 53x, 55x, 56x, 58x, 5Qx, 5Sx, 68x, 69x
• 7829-CTO
• 7853-CTO
• 7854-CTO, 3Qx, 3Tx, 3Ux, 3Vx, 3Wx, 48x, 4Jx, 4Mx
• 7856-CTO, 3Ex, 3Fx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx
• 5015-CTO, 36x, 38x, 39x, 3Ax, 3Cx
• 5016-CTO, 58x, 5Ax, 5Cx, 5Dx, 5Ex, 5Hx, 5Rx, 5Tx, 5Xx, 5Yx, 64x
• 5017-CTO
• 5019-CTO
• 7859-CTO, 3Tx, 4Nx, 4Px, 55x, 56x, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Wx, 5Xx, 63x, 64x, 65x, 66x
• 7860-CTO, 3Kx, 3Lx, 3Mx
16 SATA hard disk drive, 250 GB, 5,400 rpm, 7mmH
• 7826-CTO, 3Zx, 44x
• 7827-CTO, 52x, 53x, 55x, 56x, 58x, 5Qx, 5Sx, 68x, 69x
• 7829-CTO
• 7853-CTO
• 7854-CTO, 3Qx, 3Tx, 3Ux, 3Vx, 3Wx, 48x, 4Jx, 4Mx
• 7856-CTO, 3Ex, 3Fx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx
• 5015-CTO, 36x, 38x, 39x, 3Ax, 3Cx
• 5016-CTO, 58x, 5Ax, 5Cx, 5Dx, 5Ex, 5Hx, 5Rx, 5Tx, 5Xx, 5Yx, 64x
• 5017-CTO
• 5019-CTO
• 7859-CTO, 3Tx, 4Nx, 4Px, 55x, 56x, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Wx, 5Xx, 63x, 64x, 65x, 66x
• 7860-CTO, 3Kx, 3Lx, 3Mx
16 OPAL SATA hard disk drive, 250 GB, 7,200 rpm, 7mmH
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
FRU no.
CRU
ID
** 04W1290
04W1293
75Y5195
41W0777
41W0785
75Y5043
75Y5033
04W1286
04W1289
75Y5151
75Y5153
75Y5199
**
**
**
Chapter 10
.
Parts list
119
Table 9. Parts list—Overall (continued)
No. FRU (Overall)
16 SATA hard disk drive, 320 GB, 5,400 rpm
• 7826-CTO, 34x, 42x, 43x, 45x, 46x, 47x
• 7827-CTO, 4Lx, 5Cx, 5Jx, 5Rx, 67x
• 7829-CTO, 49x, 4Yx, 4Zx
• 7853-CTO
• 7854-CTO, 3Px, 4Lx, 4Ux, 4Vx
• 7856-CTO, 3Cx, 3Dx, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Xx
• 5015-CTO, 37x
• 5016-CTO, 4Cx, 4Dx, 5Qx, 5Sx, 5Vx, 63x
• 5017-CTO, 4Hx, 4Lx, 4Mx, 4Px
• 5019-CTO
• 7859-CTO, 3Sx, 4Hx, 4Mx, 4Yx, 4Zx, 52x, 53x, 54x, 5Ax, 5Gx, 5Hx, 5Yx, 5Zx
• 7860-CTO, 3Hx, 3Jx
16 SATA hard disk drive, 320 GB, 7,200 rpm
• 7826-CTO, 3Cx, 3Dx, 3Ex, 3Nx, 3Px, 3Qx, 3Rx, 3Xx, 3Yx
• 7827-CTO, 32x, 33x, 34x, 43x, 44x, 48x, 49x, 4Dx, 4Ex, 4Fx, 4Jx, 4Nx, 4Qx, 4Rx, 4Sx,
4Vx, 4Wx, 4Yx, 4Zx, 54x, 57x, 5Ax, 5Bx, 5Ex, 5Fx, 5Hx, 5Tx, 5Vx, 5Wx, 5Xx, 5Yx, 5Zx, 66x
• 7829-CTO, 32x, 33x, 34x, 43x, 44x, 48x, 4Dx, 4Ex, 4Fx, 4Mx, 4Rx, 4Sx, 4Ux, 4Wx, 4Xx
• 7853-CTO
• 7854-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 3Ax, 3Bx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx,
3Kx, 3Lx, 3Mx, 3Nx, 3Rx, 3Sx, 42x, 43x, 44x, 45x, 46x, 47x, 4Ax, 4Dx, 4Ex, 4Fx, 4Gx,
4Hx, 4Kx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 53x, 58x, 59x, 5Ax
• 7856-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Nx, 3Yx, 3Zx, 42x, 43x, 46x,
47x, 48x, 49x, 4Cx, 4Dx
• 5015-CTO, 3Bx
• 5016-CTO, 32x, 33x, 44x, 45x, 46x, 48x, 49x, 4Ex, 4Gx, 4Hx, 4Jx, 4Lx, 4Mx, 4Qx, 4Rx,
4Sx, 4Ux, 4Vx, 4Wx, 4Yx, 4Zx, 52x, 57x, 59x, 5Bx, 5Fx, 5Gx, 5Lx, 5Mx, 5Wx, 5Zx, 62x
• 5017-CTO, 32x, 33x, 44x, 45x, 46x, 48x, 49x, 4Ax, 4Gx, 4Jx, 4Kx, 4Nx
• 5019-CTO
• 7859-CTO, 35x, 36x, 37x, 38x, 3Dx, 3Ex, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx,
3Rx, 3Ux, 3Vx, 3Xx, 3Yx, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Kx, 4Lx, 4Qx, 4Rx, 4Sx, 4Tx,
4Ux, 4Vx, 59x, 5Dx, 5Px, 5Qx, 5Rx
• 7860-CTO, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Gx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx
16
SATA hard disk drive, 320 GB, 7,200 rpm, 7mmH
• 7826-CTO, 3Cx, 3Dx, 3Ex, 3Nx, 3Px, 3Qx, 3Rx, 3Xx, 3Yx
• 7827-CTO, 32x, 33x, 34x, 43x, 44x, 48x, 49x, 4Dx, 4Ex, 4Fx, 4Jx, 4Nx, 4Qx, 4Rx, 4Sx,
4Vx, 4Wx, 4Yx, 4Zx, 54x, 57x, 5Ax, 5Bx, 5Ex, 5Fx, 5Hx, 5Tx, 5Vx, 5Wx, 5Xx, 5Yx, 5Zx, 66x
• 7829-CTO, 32x, 33x, 34x, 43x, 44x, 48x, 4Dx, 4Ex, 4Fx, 4Mx, 4Rx, 4Sx, 4Ux, 4Wx, 4Xx
• 7853-CTO
• 7854-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 3Ax, 3Bx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx,
3Kx, 3Lx, 3Mx, 3Nx, 3Rx, 3Sx, 42x, 43x, 44x, 45x, 46x, 47x, 4Ax, 4Dx, 4Ex, 4Fx, 4Gx,
4Hx, 4Kx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 53x, 58x, 59x, 5Ax
• 7856-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Nx, 3Yx, 3Zx, 42x, 43x, 46x,
47x, 48x, 49x, 4Cx, 4Dx
• 5015-CTO, 3Bx
• 5016-CTO, 32x, 33x, 44x, 45x, 46x, 48x, 49x, 4Ex, 4Gx, 4Hx, 4Jx, 4Lx, 4Mx, 4Qx, 4Rx,
4Sx, 4Ux, 4Vx, 4Wx, 4Yx, 4Zx, 52x, 57x, 59x, 5Bx, 5Fx, 5Gx, 5Lx, 5Mx, 5Wx, 5Zx, 62x
• 5017-CTO, 32x, 33x, 44x, 45x, 46x, 48x, 49x, 4Ax, 4Gx, 4Jx, 4Kx, 4Nx
• 5019-CTO
• 7859-CTO, 35x, 36x, 37x, 38x, 3Dx, 3Ex, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx,
3Rx, 3Ux, 3Vx, 3Xx, 3Yx, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Kx, 4Lx, 4Qx, 4Rx, 4Sx, 4Tx,
4Ux, 4Vx, 59x, 5Dx, 5Px, 5Qx, 5Rx
• 7860-CTO, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Gx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx
FRU no.
CRU
ID
41W0779
41W0787
75Y5045
75Y5035
04W1287
60Y4809
60Y4819
75Y5123
04W1291
04W1294
75Y5197
**
**
**
120
Hardware Maintenance Manual
Table 9. Parts list—Overall (continued)
No. FRU (Overall)
16 SATA hard disk drive, 500 GB, 7,200 rpm
• 7826-CTO, 32x, 33x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx,
3Mx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 48x, 49x
• 7827-CTO, 42x, 45x, 46x, 47x, 4Ax, 4Bx, 4Cx, 4Gx, 4Hx, 4Kx, 4Mx, 4Px, 4Ux, 4Xx, 59x,
5Dx, 5Gx, 5Kx, 5Lx, 5Mx, 5Nx, 5Px, 62x
• 7829-CTO, 42x, 45x, 46x, 47x, 4Bx, 4Cx, 4Gx, 4Hx, 4Jx, 4Kx, 4Lx, 4Nx, 4Px, 4Qx, 4Tx, 4Vx
• 7853-CTO
• 7854-CTO, 39x, 3Cx, 3Xx, 3Yx, 3Zx, 49x, 4Bx, 4Cx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 54x, 55x,
56x, 57x, 5Bx, 5Cx, 5Dx, 5Ex
• 7856-CTO, 3Bx, 3Wx, 44x, 45x, 4Ax, 4Bx
• 5015-CTO, 32x, 33x
• 5016-CTO, 42x, 43x, 47x, 4Ax, 4Bx, 4Fx, 4Kx, 4Nx, 4Px, 4Tx, 4Xx, 53x, 56x, 5Jx, 5Kx,
5Nx, 5Px
• 5017-CTO, 42x, 43x, 47x, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx
• 5019-CTO
• 7859-CTO, 32x, 33x, 34x, 39x, 3Ax, 3Bx, 3Cx, 3Fx, 3Wx, 3Zx, 42x, 43x, 44x, 45x, 46x,
47x, 48x, 49x, 4Ax, 4Jx, 4Wx, 4Xx, 57x, 58x, 5Bx, 5Cx, 5Ex, 5Sx, 5Tx, 5Ux, 5Vx
• 7860-CTO, 32x, 33x, 34x, 3Ex, 3Fx
16 SATA solid state drive, 4 GB, 2.5", 7mmH
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
16 SATA solid state drive, 128 GB, 2.5", 7mmH
• 7826-CTO
• 7827-CTO, 4Tx
• 7829-CTO, 4Ax
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO, 34x, 35x
• 5016-CTO, 54x, 55x
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
FRU no.
CRU
ID
** 60Y4811
60Y4821
75Y5125
04W1283 **
04W1284
04W1267
04W1276
**
Chapter 10
.
Parts list
121
Table 9. Parts list—Overall (continued)
No. FRU (Overall)
17 Sierrawireless Gobi-3000 Wireless WAN card, WW SKU
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
17 Sierrawireless Gobi-3000 Wireless WAN card for Malaysia SKU
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
17 Ericsson F5521gw Wireless WAN card
• 7826-CTO, 32x
• 7827-CTO, 4Ax, 4Bx, 4Gx
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
17 Ericsson F5521gw Wireless WAN card for Malaysia SKU
• 7826-CTO
• 7827-CTO, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 5Ax, 5Bx
• 7829-CTO, 4Wx, 4Xx
• 7853-CTO
• 7854-CTO, 42x, 43x, 4Ux, 5Ax, 5Cx
• 7856-CTO
• 5015-CTO
• 5016-CTO, 4Nx, 4Px, 4Tx, 4Xx, 4Yx, 4Zx, 5Lx, 5Mx
• 5017-CTO, 4Kx, 4Lx
• 5019-CTO
• 7859-CTO, 44x, 45x, 48x, 49x, 4Yx, 59x, 5Dx, 5Ex, 5Qx
• 7860-CTO
122
Hardware Maintenance Manual
FRU no.
CRU
ID
60Y3257 **
60Y3283 **
60Y3279 **
60Y3267 **
Table 9. Parts list—Overall (continued)
No. FRU (Overall)
17 Huawei EM660 Wireless WAN card
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO, 34x
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
17 mSATA solid state drive, 80GB
• 7826-CTO, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx,
3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 42x, 43x,
44x, 45x, 46x, 47x, 48x, 49x
• 7827-CTO, 4Cx, 4Dx, 4Jx, 4Kx, 4Lx, 4Mx, 59x, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Px, 5Sx, 5Yx,
5Zx, 62x
• 7829-CTO, 4Bx, 4Cx, 4Dx, 4Hx, 4Jx, 4Nx, 4Px, 4Vx, 4Zx
• 7853-CTO
• 7854-CTO, 39x, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Px, 3Qx, 3Ux, 3Vx, 3Wx,
3Xx, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Nx, 4Qx, 4Rx, 4Tx, 4Xx, 4Yx, 4Zx, 52x,
53x, 54x, 55x, 56x, 57x, 58x, 59x
• 7856-CTO, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Rx, 3Yx, 3Zx, 42x,
43x, 44x, 45x
• 5015-CTO, 32x, 33x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx
• 5016-CTO, 5Jx, 5Kx, 5Nx, 5Px, 5Rx, 5Tx, 5Vx, 5Wx, 5Xx, 5Yx, 62x, 63x, 64x
• 5017-CTO, 4Px
• 5019-CTO
• 7859-CTO, 4Hx, 4Nx, 4Px, 4Wx, 4Xx, 55x, 56x, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Wx,
5Xx, 5Yx, 5Zx, 62x, 63x, 64x, 65x, 66x
• 7860-CTO, 3Dx, 3Hx, 3Jx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx
18 mSATA solid state drive spacer
• 7826-CTO, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx,
3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 42x, 43x,
44x, 45x, 46x, 47x, 48x, 49x
• 7827-CTO, 4Cx, 4Dx, 4Jx, 4Kx, 4Lx, 4Mx, 59x, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Px, 5Sx, 5Yx,
5Zx, 62x
• 7829-CTO, 4Bx, 4Cx, 4Dx, 4Hx, 4Jx, 4Nx, 4Px, 4Vx, 4Zx
• 7853-CTO
• 7854-CTO, 39x, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Px, 3Qx, 3Ux, 3Vx, 3Wx,
3Xx, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Nx, 4Qx, 4Rx, 4Tx, 4Xx, 4Yx, 4Zx, 52x,
53x, 54x, 55x, 56x, 57x, 58x, 59x
• 7856-CTO, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Rx, 3Yx, 3Zx, 42x,
43x, 44x, 45x
• 5015-CTO, 32x, 33x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx
• 5016-CTO, 5Jx, 5Kx, 5Nx, 5Px, 5Rx, 5Tx, 5Vx, 5Wx, 5Xx, 5Yx, 62x, 63x, 64x
• 5017-CTO, 4Px
• 5019-CTO
• 7859-CTO, 4Hx, 4Nx, 4Px, 4Wx, 4Xx, 55x, 56x, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Wx,
5Xx, 5Yx, 5Zx, 62x, 63x, 64x, 65x, 66x
• 7860-CTO, 3Dx, 3Hx, 3Jx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx
19 Thermal module with fan (integrated) for 14W Dock and 15W Dock
FRU no.
CRU
ID
60Y3239 **
45N8259 **
04W2145 *
04W1463 N
Chapter 10
.
Parts list
123
Table 9. Parts list—Overall (continued)
No. FRU (Overall)
19 Thermal module with fan (discrete) for 14W Dock and 15W Dock
20
Media Card Reader cable assembly
21 Backup battery
22 ThinkPad 11b/g/n Wireless LAN Mini-PCI Express Adapter II
• 7826-CTO, 34x, 35x, 36x, 3Cx, 3Dx, 3Ex, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx,
3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x
• 7827-CTO, 32x, 45x, 46x, 47x, 48x, 4Cx, 4Dx, 4Ex, 4Fx, 4Jx, 4Lx, 55x, 56x, 57x, 58x, 59x,
5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Px, 5Rx, 5Sx, 5Yx, 5Zx, 62x, 69x
• 7829-CTO, 32x, 45x, 46x, 47x, 48x, 4Dx, 4Ex, 4Fx, 4Lx, 4Mx, 4Tx, 4Ux, 4Yx, 4Zx
• 7853-CTO
• 7854-CTO, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx,
3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 45x, 46x, 47x, 48x, 4Ax, 4Bx, 4Dx, 4Ex,
4Fx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 5Ax, 5Bx, 5Ex
• 7856-CTO, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx,
3Px, 3Qx, 3Xx, 42x, 43x, 44x, 45x, 4Ax, 4Bx
• 5015-CTO,32x, 33x, 34x, 35x
• 5016-CTO, 32x, 4Ax, 4Bx, 4Cx, 4Dx, 4Fx, 4Gx, 4Hx, 4Jx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx,
5Jx, 5Kx, 5Nx, 5Px, 5Rx, 5Tx
• 5017-CTO, 32x, 4Px
• 5019-CTO
• 7859-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx,
3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 4Dx, 4Ex, 4Mx, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx,
4Wx, 4Xx, 5Dx, 5Px, 5Qx, 5Rx
• 7860-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 3Ax, 3Bx, 3Cx, 3Dx, 3Hx, 3Jx, 3Lx, 3Mx,
3Nx, 3Rx, 3Sx
22
Intel
®
Centrino
®
Advanced-N 6205
• 7826-CTO, 32x, 33x, 37x, 38x, 39x, 3Ax, 3Bx, 3Fx, 3Gx, 3Sx, 3Tx
• 7827-CTO, 33x, 34x, 42x, 43x, 44x, 49x, 4Ax, 4Bx, 4Gx, 4Hx, 4Kx, 4Mx, 4Nx, 4Px, 4Qx,
4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex,
5Fx, 5Qx, 5Tx, 5Wx, 5Xx, 66x
• 7829-CTO, 33x, 34x, 42x, 43x, 44x, 49x, 4Ax, 4Bx, 4Cx, 4Gx, 4Hx, 4Jx, 4Kx, 4Nx, 4Px,
4Qx, 4Rx, 4Sx, 4Vx, 4Wx, 4Xx
• 7853-CTO
• 7854-CTO, 32x, 33x, 34x, 35x, 36x, 3Xx, 3Yx, 3Zx, 42x, 43x, 44x, 49x, 4Cx, 4Gx, 4Hx,
4Jx, 4Kx, 4Ux, 4Wx, 5Cx
• 7856-CTO, 32x, 33x, 34x, 35x, 36x, 3Nx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Yx, 3Zx, 49x,
4Cx, 4Dx
• 5015-CTO, 36x, 37x, 3Ax, 3Bx
• 5016-CTO, 33x, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ex, 4Kx, 4Lx, 4Mx, 4Nx, 4Px,
4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x,
5Ax, 5Bx, 5Lx, 5Mx, 5Sx, 5Vx, 5Wx, 5Xx, 5Yx, 5Zx, 62x
• 5017-CTO, 33x, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx,
4Gx, 4Hx, 4Jx, 4Kx, 4Lx
• 5019-CTO
• 7859-CTO, 39x, 3Ax, 3Bx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx, 42x, 43x, 44x, 45x, 46x, 47x,
48x, 49x, 4Ax, 4Bx, 4Cx, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Lx, 4Nx, 4Yx, 4Zx, 57x, 58x, 59x,
5Ax, 5Bx, 5Cx, 5Ex, 5Sx
• 7860-CTO, 39x, 3Ex, 3Fx, 3Gx, 3Kx, 3Px, 3Qx
FRU no.
CRU
ID
04W1464 N
45M2870 N
92P1161
60Y3247
60Y3249
N
**
60Y3253 **
124
Hardware Maintenance Manual
Table 9. Parts list—Overall (continued)
No. FRU (Overall)
22 Intel Centrino Wireless N 1000
• 7826-CTO, 3Zx
• 7827-CTO, 5Vx, 67x, 68x
• 7829-CTO
• 7853-CTO
• 7854-CTO, 4Vx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Dx
• 7856-CTO, 46x, 47x, 48x
• 5015-CTO
• 5016-CTO, 5Qx, 63x, 64x
• 5017-CTO, 4Mx, 4Nx
• 5019-CTO
• 7859-CTO, 52x, 53x, 54x, 55x, 56x, 5Gx, 5Hx, 5Jx, 5Tx, 5Ux, 5Vx, 5Wx, 5Xx, 5Yx, 5Zx, 62x
• 7860-CTO
22 Intel Centrino Advanced-N + WiMAX 6250, MoW SKU
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO, 4Px, 5Kx, 5Lx, 5Mx, 5Nx, 63x, 64x, 65x, 66x
• 7860-CTO
22 Intel Centrino Advanced-N + WiMAX 6250, Russia SKU
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
23 Bluetooth daughter card (BDC-3.0)
• 7826-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx,
3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 42x,
43x, 44x, 45x, 46x, 47x, 48x, 49x
• 7827-CTO, 32x, 33x, 34x, 44x, 46x, 47x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx,
4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x,
53x, 54x, 56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Fx, 5Gx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Px,
5Qx, 5Rx, 5Tx, 5Vx, 5Xx, 5Yx, 5Zx, 62x, 66x
• 7829-CTO, 32x, 33x, 34x, 44x, 46x, 47x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx,
4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Sx, 4Tx, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx
• 7853-CTO
• 7854-CTO, 34x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx,
3Lx, 3Mx, 3Nx, 3Px, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx, 42x, 43x, 44x, 45x,
46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Lx, 4Mx, 4Nx,
4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 55x, 56x, 57x,
58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex
FRU no.
CRU
ID
60Y3241 **
60Y3195 **
60Y3209 **
60Y3271
60Y3275
N
Chapter 10
.
Parts list
125
Table 9. Parts list—Overall (continued)
No. FRU (Overall) FRU no.
CRU
ID
• 7856-CTO, 34x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx,
3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx, 42x, 43x, 44x,
45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx
• 5015-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 3Ax, 3Bx
• 5016-CTO, 32x, 33x, 44x, 47x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx,
4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x,
55x, 56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Px,
5Qx, 5Rx, 5Sx, 5Vx, 5Wx, 5Xx, 5Yx, 62x
• 5017-CTO, 32x, 33x, 44x, 47x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx,
4Lx, 4Mx, 4Nx, 4Px
• 5019-CTO
• 7859-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx,
3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx, 42x,
43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Lx,
4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 57x,
58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Vx
• 7860-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx,
3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx
24 CPU assembly, Intel Core™ i3-2310M Processor (2.10 GHz)
• 7826-CTO, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Wx, 3Xx, 3Yx
• 7827-CTO, 5Vx, 5Xx, 5Yx, 69x
• 7829-CTO, 4Cx, 4Vx
• 7853-CTO
• 7854-CTO, 33x, 38x, 3Dx, 3Fx, 3Hx, 3Mx, 3Nx, 3Px, 3Qx, 3Wx, 3Zx, 46x, 47x, 48x, 4Cx,
4Dx, 4Ex, 4Fx, 4Gx, 4Jx, 4Lx, 4Mx, 4Rx, 4Sx, 4Tx, 56x, 57x, 58x, 59x, 5Bx
• 7856-CTO, 33x, 38x, 39x, 3Dx, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Qx, 3Ux, 3Vx, 3Xx,
43x, 45x, 4Ax, 4Bx
• 5015-CTO, 38x, 39x, 3Cx
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO, 33x, 38x, 3Gx, 3Jx, 3Lx, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Yx, 42x, 43x, 4Ex, 4Fx,
4Lx, 4Ux, 4Vx, 4Xx, 53x, 54x, 55x, 56x, 5Gx, 5Hx, 5Kx, 5Lx
• 7860-CTO, 33x, 38x, 3Bx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Mx, 3Sx
24
CPU assembly, Intel Core i3-2330M Processor (2.20 GHz) J1
• 7826-CTO, 45x
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO, 4Dx
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO, 5Rx, 5Yx, 5Zx, 63x, 64x
• 7860-CTO
04W0495 N
04W1891 N
126
Hardware Maintenance Manual
Table 9. Parts list—Overall (continued)
No. FRU (Overall)
24 CPU assembly, Intel Core i3-2350M Processor (2.30 GHz) J1
• 7826-CTO, 46x
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO, 5Ex
• 7856-CTO, 4Cx
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO, 5Px, 5Ux, 5Vx
• 7860-CTO
24 CPU assembly, Intel Core i5-2410M Processor (2.30 GHz)
• 7826-CTO, 3Hx, 3Lx, 3Ux, 3Vx
• 7827-CTO, 49x, 5Zx, 62x
• 7829-CTO
• 7853-CTO
• 7854-CTO, 32x, 37x, 3Cx, 3Ex, 3Gx, 3Jx, 3Kx, 3Lx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 43x, 44x,
45x, 49x, 4Ax, 4Bx, 4Hx, 4Nx, 4Px, 4Qx, 4Vx, 4Wx, 53x, 54x, 55x, 5Ax
• 7856-CTO, 32x, 37x, 3Ax, 3Bx, 3Cx, 3Ex, 3Nx, 3Px, 3Rx, 3Sx, 3Tx, 3Wx, 42x
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO, 32x, 36x, 37x, 3Fx, 3Hx, 3Kx, 3Mx, 3Nx, 3Px, 3Vx, 3Wx, 3Xx, 4Cx, 4Dx, 4Gx,
4Mx, 4Qx, 4Rx, 4Sx, 4Tx, 4Zx, 52x, 57x, 58x, 5Ax, 5Dx
• 7860-CTO, 32x, 36x, 37x, 39x, 3Ax, 3Cx, 3Kx, 3Lx, 3Rx
24 CPU assembly, Intel Core i5-2430M Processor (2.40 GHz) J1
• 7826-CTO, 47x, 48x, 49x
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO, 5Dx
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO, 5Qx, 5Sx, 5Tx, 62x
• 7860-CTO
24
CPU assembly, Intel Core i5-2520M Processor (2.50 GHz)
• 7826-CTO, 32x, 33x, 34x, 35x, 36x, 38x, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Jx, 3Kx, 3Tx, 3Zx
• 7827-CTO, 32x, 34x, 43x, 44x, 48x, 4Ax, 4Bx, 4Dx, 4Ex, 4Fx, 4Gx, 4Jx, 4Nx, 4Yx, 4Zx,
52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Bx, 5Cx, 5Ex, 5Fx, 5Hx, 5Kx, 5Lx, 5Mx, 5Nx,
5Px, 5Rx, 5Sx, 5Tx, 5Wx, 66x, 67x
• 7829-CTO, 32x, 34x, 43x, 44x, 48x, 4Ax, 4Bx, 4Dx, 4Lx, 4Mx, 4Rx, 4Sx, 4Ux, 4Zx
• 7853-CTO
• 7854-CTO, 34x, 35x, 36x, 39x, 3Ax, 3Bx, 3Xx, 3Yx, 42x, 4Kx, 4Ux, 4Zx, 52x, 5Cx
• 7856-CTO, 34x, 35x, 36x, 3Yx, 3Zx, 44x, 46x
• 5015-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 3Ax, 3Bx
• 5016-CTO, 32x, 42x, 43x, 44x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Gx, 4Hx, 4Jx, 4Lx, 4Sx, 4Wx,
4Zx, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 5Kx, 5Mx, 5Nx, 5Px, 5Sx, 5Tx,
5Vx, 5Wx, 5Xx, 5Yx, 62x, 63x
• 5017-CTO, 32x, 42x, 43x, 44x, 48x, 49x, 4Cx, 4Dx, 4Ex, 4Kx, 4Lx, 4Mx, 4Nx, 4Px
FRU no.
CRU
ID
04W1892 N
04W0496 N
04W1893 N
04W0492 N
Chapter 10
.
Parts list
127
Table 9. Parts list—Overall (continued)
No. FRU (Overall)
• 5019-CTO
• 7859-CTO, 34x, 35x, 3Cx, 3Dx, 3Ex, 3Zx, 4Hx, 4Kx, 4Nx, 4Px, 4Wx, 4Yx, 59x, 5Bx, 5Cx
• 7860-CTO, 34x, 35x, 3Dx, 3Nx, 3Px, 3Qx
24 CPU assembly, Intel Core i5-2540M Processor (2.60 GHz)
• 7826-CTO, 37x, 3Ax, 3Sx
• 7827-CTO, 33x, 42x, 45x, 46x, 47x, 4Lx, 4Mx, 4Rx, 4Sx, 4Tx, 4Wx, 4Xx, 5Dx, 5Gx,
5Jx, 5Qx
• 7829-CTO, 33x, 42x, 45x, 46x, 47x, 49x, 4Jx, 4Kx, 4Qx, 4Tx, 4Xx, 4Yx
• 7853-CTO
• 7854-CTO, 4Yx
• 7856-CTO, 47x, 48x
• 5015-CTO
• 5016-CTO, 33x, 45x, 46x, 47x, 4Dx, 4Ex, 4Kx, 4Px, 4Qx, 4Rx, 4Vx, 4Yx, 55x, 56x, 57x,
58x, 5Qx, 5Rx, 5Zx
• 5017-CTO, 33x, 45x, 46x, 47x, 4Fx, 4Gx, 4Hx
• 5019-CTO
• 7859-CTO, 3Ax, 3Bx, 48x, 49x, 4Ax, 4Bx, 4Jx, 5Ex
• 7860-CTO
24
CPU assembly, Intel Core i7-2620M Processor (2.70 GHz)
• 7826-CTO, 39x
• 7827-CTO, 4Cx, 4Hx, 4Kx, 4Px, 4Qx, 4Ux, 4Vx, 5Ax
• 7829-CTO, 4Ex, 4Fx, 4Gx, 4Hx, 4Nx, 4Px, 4Wx
• 7853-CTO
• 7854-CTO, 4Xx
• 7856-CTO, 49x
• 5015-CTO
• 5016-CTO, 4Fx, 4Mx, 4Nx, 4Tx, 4Ux, 4Xx, 52x, 53x, 54x, 5Lx
• 5017-CTO, 4Ax, 4Bx, 4Jx
• 5019-CTO
• 7859-CTO, 39x, 44x, 45x, 46x, 47x
• 7860-CTO
24 CPU assembly, Intel Pentium
®
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
B940 Processor (2.0 GHz), Q0
FRU no.
CRU
ID
04W0493 N
04W0494 N
04W1894 N
128
Hardware Maintenance Manual
Table 9. Parts list—Overall (continued)
No. FRU (Overall)
24 CPU assembly, Intel Pentium B950 Processor (2.1 GHz), Q0
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
24 CPU assembly, Intel Celeron
®
• 7826-CTO, 44x
B800 Processor (1.5 GHz), Q0
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO, 5Wx, 5Xx, 65x, 66x
• 7860-CTO
24 CPU assembly, Intel Celeron B810 Processor (1.6 GHz), Q0
• 7826-CTO, 42x, 43x
• 7827-CTO, 68x
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO, 64x
• 5017-CTO
• 5019-CTO
• 7859-CTO, 5Jx, 5Mx, 5Nx
• 7860-CTO
25 System board assembly, HM65 integrated 14W Dock, TPM, AUO4, without wireless WAN
• 7826-CTO, 36x, 3Dx, 3Ex, 3Gx
• 7827-CTO, 5Lx, 5Mx, 5Sx
• 7829-CTO, 4Zx
• 7853-CTO
• 7854-CTO, 48x, 4Fx
• 7856-CTO, 3Lx
25 System board assembly, HM65 integrated 14W Dock, non-TPM, AUO4, without wireless WAN
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO, 3Mx
FRU no.
CRU
ID
04W1895 N
04W3399 N
04W1896 N
04W0376 N
04W0377 N
Chapter 10
.
Parts list
129
Table 9. Parts list—Overall (continued)
No. FRU (Overall)
25 System board assembly, HM65 integrated 14W Dock, TPM, AUO4, with wireless WAN
• 7826-CTO, 32x, 3Zx
• 7827-CTO, 32x, 33x, 34x, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Gx, 4Hx, 4Nx,
4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 55x, 56x, 57x, 58x,
5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Qx, 5Rx, 5Tx, 5Vx, 5Wx, 5Xx, 66x, 67x, 68x, 69x
• 7829-CTO, 32x, 33x, 34x, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Ex, 4Fx, 4Gx, 4Kx,
4Lx, 4Mx, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Wx, 4Xx, 4Yx
• 7853-CTO
• 7854-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 3Rx, 3Sx, 3Tx, 3Yx, 3Zx, 42x, 43x, 44x, 45x,
46x, 4Gx, 4Hx, 4Jx, 4Kx, 4Lx, 4Mx, 4Ux, 4Vx, 4Wx, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex
• 7856-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Nx, 3Px, 3Qx, 3Sx, 3Tx, 3Ux,
3Vx, 3Wx, 3Xx, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx
25 System board assembly, HM65 integrated 14W Dock, non-TPM, AUO4, with wireless WAN
• 7826-CTO
• 7827-CTO, 4Ex, 4Fx
• 7829-CTO
• 7853-CTO
• 7854-CTO, 3Ax, 3Lx, 3Mx, 3Nx, 4Px, 4Sx
• 7856-CTO
25 System board assembly, HM65 14W non-docking, TPM, AUO4, without wireless WAN
• 7826-CTO, 34x, 3Px, 3Qx, 3Rx, 3Yx, 42x
• 7827-CTO, 4Kx, 4Lx, 5Jx, 5Px
• 7829-CTO, 4Nx
• 7853-CTO
• 7854-CTO, 3Ux, 3Vx, 3Wx, 59x
• 7856-CTO, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Jx, 3Zx, 42x, 43x, 44x, 45x
25 System board assembly, HM65 14W non-docking, non-TPM, AUO4, without wireless WAN
• 7826-CTO, 44x
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO, 3Jx, 3Kx, 3Px, 3Qx, 4Nx, 4Tx
• 7856-CTO, 3Kx
25 System board assembly, HM65 + AMD 1GB 14W non-docking, TPM, AUO4, without wireless
WAN
• 7826-CTO, 33x, 35x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Fx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx,
3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 43x
• 7827-CTO, 4Jx, 4Mx, 59x, 5Kx, 5Nx, 5Yx, 5Zx, 62x
• 7829-CTO, 4Bx, 4Cx, 4Dx, 4Hx, 4Jx, 4Px, 4Vx
• 7853-CTO
• 7854-CTO, 3Xx, 47x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 55x,
56x, 57x, 58x
• 7856-CTO, 3Hx, 3Rx, 3Yx
25 System board assembly, HM65 + AMD 1GB 14W non-docking, non-TPM, AUO4, without wireless WAN
• 7826-CTO, 45x, 46x, 47x, 48x, 49x
• 7827-CTO, 4Cx, 4Dx
• 7829-CTO
• 7853-CTO
• 7854-CTO, 39x, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 4Qx, 4Rx
• 7856-CTO, 3Gx
FRU no.
CRU
ID
04W0378 N
04W0379 N
04W0480 N
04W0481 N
04W0482 N
04W0483 N
130
Hardware Maintenance Manual
Table 9. Parts list—Overall (continued)
No. FRU (Overall)
25 System board assembly, HM65 integrated 15W Dock, TPM, AUO4, without wireless WAN
• 5015-CTO, 33x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx
• 5016-CTO, 5Kx, 5Px, 5Rx, 5Tx, 5Vx, 5Wx, 5Xx, 5Yx, 62x, 63x, 64x
• 5017-CTO, 4Px
• 5019-CTO
• 7859-CTO, 4Hx, 4Nx, 4Px, 4Wx, 4Xx, 55x, 56x, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Wx,
5Xx, 5Yx, 5Zx, 62x, 63x, 64x, 65x, 66x
• 7860-CTO, 3Dx, 3Jx, 3Nx, 3Qx, 3Rx, 3Sx
25
System board assembly, HM65 integrated 15W Dock, non-TPM, AUO4, without wireless WAN
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO, 3Hx
25 System board assembly, HM65 integrated 15W Dock, TPM, AUO4, with wireless WAN
• 5015-CTO, 34x
• 5016-CTO, 32x, 33x, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Lx, 4Tx,
4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx,
5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Mx, 5Qx, 5Zx
• 5017-CTO, 32x, 33x, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Dx, 4Ex, 4Fx, 4Gx, 4Jx,
4Lx, 4Mx, 4Nx
• 5019-CTO
• 7859-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx,
42x, 43x, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Kx, 4Lx, 4Mx, 52x, 53x, 54x, 58x, 59x, 5Ax, 5Bx,
5Cx, 5Dx, 5Ex, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Vx
• 7860-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Ex, 3Fx, 3Gx, 3Kx,
3Lx, 3Mx
25
System board assembly, HM65 integrated 15W Dock, non-TPM, AUO4, with wireless WAN
• 5015-CTO
• 5016-CTO, 4Hx, 4Jx
• 5017-CTO
• 5019-CTO
• 7859-CTO, 3Dx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 4Qx, 4Rx, 4Vx
• 7860-CTO
26 ExpressCard slot blank bezel
26 SmartCard Reader
op
• 7826-CTO
• 7827-CTO, 4Zx
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO, 4Px
• 5019-CTO
• 7859-CTO
• 7860-CTO
FRU no.
CRU
ID
04W0384 N
04W0385 N
04W0386 N
04W0387 N
04W1721 N
41N3045
03X6352
*
Chapter 10
.
Parts list
131
Table 9. Parts list—Overall (continued)
No. FRU (Overall)
27 Palm rest assembly with fingerprint reader for 14W Dock
• 7826-CTO, 32x, 36x, 3Ex, 3Gx
• 7827-CTO, 33x, 34x, 44x, 46x, 47x, 49x, 4Ax, 4Bx, 4Ex, 4Fx, 4Gx, 4Hx, 4Nx, 4Px, 4Rx,
4Tx, 4Ux, 4Xx, 4Yx, 4Zx, 5Ax, 5Bx, 5Cx, 5Fx, 5Gx, 5Lx, 5Qx, 5Tx, 5Vx, 5Xx, 66x
• 7829-CTO, 33x, 34x, 44x, 46x, 47x, 49x, 4Ax, 4Fx, 4Gx, 4Kx, 4Lx, 4Mx, 4Sx, 4Tx, 4Wx,
4Xx, 4Yx, 4Zx
• 7853-CTO
• 7854-CTO, 34x, 36x, 37x, 38x, 3Ax, 3Lx, 3Mx, 3Nx, 3Rx, 3Sx, 3Yx, 3Zx, 4Gx, 4Hx, 4Lx,
4Px, 4Sx, 4Ux, 4Vx, 4Wx, 5Bx, 5Cx, 5Dx, 5Ex
• 7856-CTO, 34x, 36x, 37x, 38x, 39x, 3Ax, 3Lx, 3Mx, 3Wx, 3Xx, 46x, 47x, 48x, 49x, 4Ax, 4Bx
27 Palm rest assembly without fingerprint reader for 15W Dock
• 5015-CTO, 38x, 39x, 3Cx
• 5016-CTO, 42x, 43x, 45x, 46x, 48x, 5Dx, 5Tx, 5Zx, 63x, 64x
• 5017-CTO, 42x, 43x, 45x, 46x, 48x
• 5019-CTO
• 7859-CTO, 3Tx, 55x, 56x, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Wx, 5Xx, 5Yx, 5Zx, 62x,
63x, 64x, 65x, 66x
• 7860-CTO
27 Palm rest assembly with fingerprint reader for 15W Dock
• 5015-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 3Ax, 3Bx
• 5016-CTO, 33x, 44x, 47x, 49x, 4Ax, 4Bx, 4Cx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Lx, 4Mx,
4Nx, 4Px, 4Qx, 4Rx, 4Tx, 4Ux, 4Xx, 4Yx, 53x, 54x, 55x, 56x, 57x, 59x, 5Jx, 5Kx, 5Lx, 5Mx,
5Nx, 5Qx, 5Rx, 5Sx, 5Vx, 5Wx, 5Xx, 5Yx, 62x
• 5017-CTO, 33x, 44x, 47x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Lx,
4Mx, 4Nx, 4Px
• 5019-CTO
• 7859-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx,
3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx, 42x, 43x, 4Fx, 4Gx,
4Hx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x,
55x, 56x, 57x, 58x, 5Ax, 5Bx, 5Gx, 5Hx, 5Jx, 5Sx, 5Tx, 5Ux, 5Vx, 5Wx, 5Xx, 5Yx, 5Zx,
62x, 63x, 64x, 65x, 66x
• 7860-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx,
3Hx, 3Jx, 3Nx
28
Keyboard (see “Keyboard” on page 137.)
29 TrackPoint caps
—
ac power adapter (see “ac power adapters” on page 140.)
FRU no.
CRU
ID
04W1350 N
04W1351 N
04W1352 N
91P9642 *
LCD FRUs
In ThinkPad L420, L421, and L520, there are following types of LCDs.
• 14.0-inch HD LED-backlight LCD (Table 10 “Parts list—14.0-inch HD LCD” on page 134)
• 15.6-inch HD LED-backlight LCD (Table 11 “Parts list—15.6-inch HD LCD” on page 135)
• 15.6-inch HDx, LED-backlight LCD (Table 12 “Parts list—15.6-inch HD+ LCD” on page 136)
132
Hardware Maintenance Manual
9
8
7
6
1
2
3
4
5
Chapter 10
.
Parts list
133
Table 10. Parts list—14.0-inch HD LCD
No. FRU (14.0-inch HD LCD)
1
LCD front bezel for 14W
2 Integrated camera with microphone (1M)
• 7826-CTO, 32x, 33x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx,
3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 42x, 43x,
44x, 45x, 46x, 47x, 48x, 49x
• 7827-CTO, 33x, 34x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx,
4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 53x, 54x, 57x,
58x, 59x, 5Ax, 5Bx, 5Cx, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Px, 5Rx, 5Tx, 5Vx, 5Xx,
5Yx, 5Zx, 62x, 66x, 69x
• 7829-CTO, 33x, 34x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx,
4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx
• 7853-CTO
• 7854-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx,
3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Xx, 3Yx, 3Zx, 42x, 43x,
44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Lx, 4Mx,
4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 55x, 56x,
57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex
• 7856-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx,
3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx,
42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx
2 Microphone
• 7826-CTO, 34x, 3Zx
• 7827-CTO, 32x, 42x, 43x, 44x, 45x, 4Sx, 52x, 55x, 56x, 5Dx, 5Ex, 5Fx, 5Qx, 5Sx, 5Wx,
67x, 68x
• 7829-CTO, 32x, 42x, 43x, 44x, 45x, 4Qx, 4Rx, 4Sx
• 7853-CTO
• 7854-CTO, 3Vx, 3Wx
• 7856-CTO
3 Wireless WAN antenna set 14W
4 Hinges 14W
5 LCD cover kit Texture 14W (with logo), silver
6 Speaker assembly for 14W
7
LCD cable, HD, Teflon 14W
8
LCD module, 14.0-inch HD anti-glare
• 7826-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx,
3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx,
42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x
• 7827-CTO, 32x, 33x, 34x, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx,
4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx,
4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx,
5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Vx, 5Wx, 5Xx, 5Yx, 5Zx,
62x, 66x, 67x, 68x, 69x
• 7829-CTO, 32x, 33x, 34x, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx,
4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx,
4Xx, 4Yx, 4Zx
• 7853-CTO
• 7854-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx,
3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx,
42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx,
4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x,
55x, 56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex
FRU no.
CRU
ID
04W1735 N
04W0442
04W0443
04W0444
04W0445
N
60Y3329 N
04W1725 N
04W1731
04W1732
N
04W1722 N
60Y3333 N
04W1728 N
93P5729
93P5725
93P5721
93P5733
04W0411
N
134
Hardware Maintenance Manual
Table 10. Parts list—14.0-inch HD LCD (continued)
No. FRU (14.0-inch HD LCD)
• 7856-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx,
3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx,
42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx
9 Wireless LAN antenna set 14W
Table 11. Parts list—15.6-inch HD LCD
No. FRU (15.6-inch HD LCD)
1 LCD front bezel for 15W
2 Integrated camera with microphone (1M)
• 5015-CTO, 32x, 33x, 34x, 35x
• 5016-CTO, 33x, 44x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Jx, 4Lx, 4Rx, 4Sx, 4Xx,
4Yx, 4Zx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Bx, 5Cx, 5Gx, 5Hx, 5Mx,
5Nx, 5Px, 5Qx, 5Sx, 62x
• 5017-CTO, 33x, 44x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Mx, 4Nx, 4Px
• 5019-CTO
• 7859-CTO, 32x, 35x, 37x, 38x, 3Bx, 3Kx, 3Lx, 3Nx, 3Px, 3Sx, 3Tx, 3Ux, 3Vx,
3Wx, 3Xx, 3Yx, 43x, 44x, 47x, 48x, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Jx, 4Kx,
4Lx, 4Rx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 52x, 53x, 54x, 59x, 5Cx, 5Dx, 5Kx, 5Lx,
5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Tx, 5Ux, 5Vx, 63x, 64x, 65x, 66x
• 7860-CTO, 32x, 35x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx,
3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx
2 Microphone
• 5015-CTO, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx
• 5016-CTO, 32x, 42x, 43x, 48x, 5Ax, 5Dx, 5Ex, 5Fx, 5Rx, 5Tx, 5Vx, 5Wx, 5Xx,
5Yx, 63x, 64x
• 5017-CTO, 32x, 42x, 43x, 48x
• 5019-CTO
• 7859-CTO, 4Hx, 4Nx, 4Px, 55x, 56x, 5Gx, 5Hx, 5Jx, 5Wx, 5Xx, 5Yx, 5Zx, 62x
• 7860-CTO
3 Wireless WAN antenna set 15W
4 Hinges 15W
FRU no.
04W1736
04W0442
04W0443
04W0444
04W0445
60Y3329
5
LCD cover kit Texture 15W (with logo), silver
6
Speaker assembly for 15W
7 LCD cable, HD, Teflon 15W
• 5015-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx
• 5016-CTO, 32x, 33x, 42x, 43x, 44x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Jx,
4Lx, 4Rx, 4Sx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Ax,
5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Vx,
5Wx, 5Xx, 5Yx, 62x, 63x, 64x
• 5017-CTO, 32x, 33x, 42x, 43x, 44x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx,
4Gx, 4Mx, 4Nx, 4Px
• 5019-CTO
• 7859-CTO, 32x, 35x, 37x, 38x, 3Bx, 3Kx, 3Lx, 3Nx, 3Px, 3Sx, 3Tx, 3Ux, 3Vx,
3Wx, 3Xx, 3Yx, 43x, 44x, 47x, 48x, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx,
4Kx, 4Lx, 4Nx, 4Px, 4Rx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 52x, 53x, 54x, 55x, 56x,
59x, 5Cx, 5Dx, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Tx, 5Ux,
5Vx, 5Wx, 5Xx, 5Yx, 5Zx, 62x, 63x, 64x, 65x, 66x
• 7860-CTO, 32x, 35x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx,
3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx
04W1727
04W1733
04W1734
04W1723
60Y3334
04W1729
FRU no.
CRU
ID
04W1724 N
CRU ID
N
N
N
N
N
N
N
N
Chapter 10
.
Parts list
135
Table 11. Parts list—15.6-inch HD LCD (continued)
No. FRU (15.6-inch HD LCD)
8 LCD module, 15.6-inch HD anti-glare
• 5015-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx
• 5016-CTO, 32x, 33x, 42x, 43x, 44x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Jx,
4Lx, 4Rx, 4Sx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Ax,
5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Vx,
5Wx, 5Xx, 5Yx, 62x, 63x, 64x
• 5017-CTO, 32x, 33x, 42x, 43x, 44x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx,
4Gx, 4Mx, 4Nx, 4Px
• 5019-CTO
• 7859-CTO, 32x, 35x, 37x, 38x, 3Bx, 3Kx, 3Lx, 3Nx, 3Px, 3Sx, 3Tx, 3Ux, 3Vx,
3Wx, 3Xx, 3Yx, 43x, 44x, 47x, 48x, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx,
4Kx, 4Lx, 4Nx, 4Px, 4Rx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 52x, 53x, 54x, 55x, 56x,
59x, 5Cx, 5Dx, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Tx, 5Ux,
5Vx, 5Wx, 5Xx, 5Yx, 5Zx, 62x, 63x, 64x, 65x, 66x
• 7860-CTO, 32x, 35x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx,
3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx
9 Wireless LAN antenna set 15W
FRU no.
04W0424
04W0428
04W0430
04W0426
04W1726
CRU ID
N
N
Table 12. Parts list—15.6-inch HD+ LCD
No. FRU (15.6-inch HD+ LCD)
1 LCD front bezel 15W
2 Integrated camera with microphone (1M)
• 5015-CTO
• 5016-CTO, 45x, 46x, 47x, 4Fx, 4Gx, 4Hx, 4Kx, 4Mx, 4Nx, 4Px, 4Qx, 4Tx, 4Ux, 4Vx, 4Wx,
5Jx, 5Kx, 5Lx
• 5017-CTO, 45x, 46x, 47x, 4Hx, 4Jx, 4Kx, 4Lx
• 5019-CTO
• 7859-CTO, 33x, 34x, 36x, 39x, 3Ax, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Mx, 3Qx, 3Rx,
3Zx, 42x, 45x, 46x, 49x, 4Ax, 4Mx, 4Qx, 4Sx, 4Yx, 4Zx, 57x, 58x, 5Ax, 5Bx, 5Ex, 5Sx
• 7860-CTO, 33x, 34x, 36x
2 Microphone
• 5015-CTO
• 5016-CTO, 5Zx
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
3 Wireless WAN antenna set 15W
4 Hinges 15W
5 LCD cover kit Texture 15W (with logo), silver
6 Speaker assembly for 15W
7
LCD cable, HD + Teflon 15W
• 5015-CTO
• 5016-CTO, 45x, 46x, 47x, 4Fx, 4Gx, 4Hx, 4Kx, 4Mx, 4Nx, 4Px, 4Qx, 4Tx, 4Ux, 4Vx, 4Wx,
5Jx, 5Kx, 5Lx, 5Zx
• 5017-CTO, 45x, 46x, 47x, 4Hx, 4Jx, 4Kx, 4Lx
• 5019-CTO
• 7859-CTO, 33x, 34x, 36x, 39x, 3Ax, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Mx, 3Qx, 3Rx,
3Zx, 42x, 45x, 46x, 49x, 4Ax, 4Mx, 4Qx, 4Sx, 4Yx, 4Zx, 57x, 58x, 5Ax, 5Bx, 5Ex, 5Sx
• 7860-CTO, 33x, 34x, 36x
FRU no.
CRU
ID
04W1736 N
04W0442
04W0443
04W0444
04W0445
N
60Y3329 N
04W1727 N
04W1733
04W1734
N
04W1723 N
60Y3334 N
04W1730 N
136
Hardware Maintenance Manual
Table 12. Parts list—15.6-inch HD+ LCD (continued)
No. FRU (15.6-inch HD+ LCD)
8 LCD module, 15.6-inch HD+ anti-glare
• 5015-CTO
• 5016-CTO, 45x, 46x, 47x, 4Fx, 4Gx, 4Hx, 4Kx, 4Mx, 4Nx, 4Px, 4Qx, 4Tx, 4Ux, 4Vx, 4Wx,
5Jx, 5Kx, 5Lx, 5Zx
• 5017-CTO, 45x, 46x, 47x, 4Hx, 4Jx, 4Kx, 4Lx
• 5019-CTO
• 7859-CTO, 33x, 34x, 36x, 39x, 3Ax, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Mx, 3Qx, 3Rx,
3Zx, 42x, 45x, 46x, 49x, 4Ax, 4Mx, 4Qx, 4Sx, 4Yx, 4Zx, 57x, 58x, 5Ax, 5Bx, 5Ex, 5Sx
• 7860-CTO, 33x, 34x, 36x
9 Wireless LAN antenna set 15W
FRU no.
CRU
ID
42T0743
93P5681
N
04W1726 N
Keyboard
Table 13. Parts list—Keyboard
Language
Arabic
Belgian
Brazilian Portuguese
Bulgarian
Canadian French (058)
Canadian French (Acnor)
Czech
Danish
Dutch
Finnish, Swedish
French
German
Greek (U.S. English and Greek layout)
Hebrew
Hungarian
Icelandic
Indian English
Italian
Japanese
Korean
Latin American Spanish
Norwegian
Polish
Portuguese
Russian
FRU no.
45N2288 45N2358 45N2428
45N2289 45N2359 45N2429
45N2287 45N2357 45N2427
45N2290 45N2360 45N2430
45N2285 45N2355 45N2425
45N2284 45N2354 45N2424
45N2291 45N2361 45N2431
45N2292 45N2362 45N2432
45N2302 45N2372 45N2442
45N2309 45N2379 45N2449
45N2294 45N2364 45N2434
45N2295 45N2365 45N2435
45N2296 45N2366 45N2436
45N2297 45N2367 45N2437
45N2298 45N2368 45N2438
45N2299 45N2369 45N2439
63Y0225 63Y0227 63Y0229
45N2300 45N2370 45N2440
45N2314 45N2384 45N2454
45N2315 45N2385 45N2455
45N2286 45N2356 45N2426
45N2303 45N2373 45N2443
45N2304 45N2374 45N2444
45N2305 45N2375 45N2445
45N2306 45N2376 45N2446
CRU
ID
N
Chapter 10
.
Parts list
137
Table 13. Parts list—Keyboard (continued)
Language
Slovak
Slovenian
Spanish
Swiss
Thai
Traditional Chinese
Turkish
Turkish F
U.K. English
U.S. English
U.S. English (International, with a Euro symbol)
Miscellaneous parts
Table 14. Parts list—Miscellaneous parts
FRU
Screw kit (including nylon-coated screws):
• M2 × 2 mm (silver), flat-head (1)
• M2 × 3 mm (black), flat-head (43)
• M2 × 5 mm (black), flat-head (48)
• M2 × 6 mm (black), flat-head (2)
• M2 × 8 mm (black), flat-head (2)
• M2.5 × 6.5 mm (black), flat-head (8)
• M3 × 3.5 mm (silver), flat-head (4)
Seal kit:
• Tape for LCD cable (large)
• Tape S (cable fix)
• Tape L (cable fix)
• Screw cap, thin
• Screw cap square
Docking connector cover
Table 15. Parts list—Miscellaneous parts
FRU
• Rubber foot (front)
• Rubber foot (rear)
• LCD latch knob
• LCD latch
• Latch link wire
• LCD latch spring
• Wireless radio switch knob
• Wireless radio switch latch
• Security keyhole bracket
• EMI spring (optical drive)
• EMI spring (HDD front)
138
Hardware Maintenance Manual
FRU no.
45N2307 45N2377 45N2447
45N2308 45N2378 45N2448
45N2293 45N2363 45N2433
45N2310 45N2380 45N2450
45N2317 45N2387 45N2457
45N2316 45N2386 45N2456
45N2311 45N2381 45N2451
60Y9558 60Y9560 60Y9556
45N2312 45N2382 45N2452
45N2283 45N2353 45N2423
45N2313 45N2383 45N2453
CRU
ID
FRU no.
CRU
ID
60Y4343 N
60Y4344 N
04W1465 *
FRU no.
CRU
ID
Table 15. Parts list—Miscellaneous parts (continued)
FRU
• EMI spring (HDD rear)
• Gasket (long)
• Gasket (short)
• HDD guide (front)
• HDD rubber rail (front)
• HDD guide (rear)
• HDD rubber rail (rear)
• LCD latch rubber
• Pad, battery
• Sponge (large)
• Sponge (small)
• Cap for Mg
System miscellaneous parts:
• Expansion slot cover
• HDD cover
• I/O sub bracket
• Connector cap
• Optical drive bracket
System board miscellaneous parts:
• Mini Card stud, system board
• Stud, system board
• Insulation (top)
• Insulation, black (battery)
• Insulation, black (coil)
• Insulation, black (SIM)
• SIM card bracket
• Eject sheet
• USB gascket
LCD miscellaneous parts:
• Heat spreader for camera
• ThinkPad logo
• Lenovo logo
• Label (camera)
• Label (no camera)
• Label (LED)
• Tape cable fix (10 × 38)
• LCD latch R
• LCD latch L
• Rubber 0.5
• Rubber 0.8
• Rubber 0.8 long
• Rubber 1.0
• Rubber 1.5
• Alpet sheet for LCD
• Gasket for LCD
• Screw cap, thin
• Screw cap, square
Note: Italicized letter in parentheses is reference to the exploded view in “LCD FRUs” on page 132.
FRU no.
CRU
ID
N
N
N
Chapter 10
.
Parts list
139
ac power adapters
Table 16. Parts list—2-pin ac power adapters
FRU
2-pin (65 W, 20 V) adapter (models CTO, xxE, xxF, xxJ, xxL, xxP, xxS, xxU, xxY)
2-pin (65 W, 20 V) adapter (models CTO, xxE, xxF, xxJ, xxL, xxP, xxS, xxU, xxY)
2-pin (65 W, 20 V) adapter (models CTO, xxE, xxF, xxJ, xxL, xxP, xxS, xxU, xxY)
2-pin (90 W, 20 V) adapter (models CTO, xxE, xxF, xxJ, xxL, xxP, xxS, xxU, xxY)
2-pin (90 W, 20 V) adapter (models CTO, xxE, xxF, xxJ, xxL, xxP, xxS, xxU, xxY)
2-pin (90 W, 20 V) adapter (models CTO, xxE, xxF, xxJ, xxL, xxP, xxS, xxU, xxY)
2-pin (90 W, 20 V) adapter (models CTO, xxE, xxF, xxJ, xxL, xxP, xxS, xxU, xxY)
Table 17. Parts list—3-pin ac power adapters
FRU
3-pin (65 W, 20 V) adapter (models CTO, xxA, xxB, xxC, xxG, xxH, xxK, xxM, xxQ, xxT, xxV)
3-pin (65 W, 20 V) adapter (models CTO, xxA, xxB, xxC, xxG, xxH, xxK, xxM, xxQ, xxT, xxV)
3-pin (65 W, 20 V) adapter (models CTO, xxA, xxB, xxC, xxG, xxH, xxK, xxM, xxQ, xxT, xxV)
3-pin (90 W, 20 V) adapter (models CTO, xxA, xxB, xxC, xxG, xxH, xxK, xxM, xxQ, xxT, xxV)
3-pin (90 W, 20 V) adapter (models CTO, xxA, xxB, xxC, xxG, xxH, xxK, xxM, xxQ, xxT, xxV)
3-pin (90 W, 20 V) adapter (models CTO, xxA, xxB, xxC, xxG, xxH, xxK, xxM, xxQ, xxT, xxV)
3-pin (90 W, 20 V) adapter (models CTO, xxA, xxB, xxC, xxG, xxH, xxK, xxM, xxQ, xxT, xxV)
FRU no.
CRU
ID
42T5282 *
42T4419
42T4423
42T4427
42T4431
42T4435
42T4439
FRU no.
CRU
ID
42T5283 *
42T4417
42T4421
42T4425
42T4429
42T4433
45N0068
Power cords
A ThinkPad power cord for a specific country or region is usually available only in that country or region:
Table 18. Parts list—2-pin power cords
Country or region FRU no.
42T5020 42T5105
CRU
ID
* Argentina
• models -CTO, xxY
Brazil
• models -CTO, xxP
Canada, U.S.
• models -CTO, xxF, xxL, xxS, xxU
Japan
• models -CTO, xxE, xxJ
42T5180 42T5183
42T5008 42T5093
42T5014 42T5099
140
Hardware Maintenance Manual
Table 19. Parts list—3-pin power cords
Country or region
Australia, New Zealand
• models -CTO, xxM
Bangladesh, Sri Lanka, South Africa
• models -CTO, xxG
Canada, U.S.
• models -CTO, xxT
China (P.R.C.) (other than Hong Kong S.A.R.)
• models -CTO, xxC
Denmark
• models -CTO, xxG
European countries
• models -CTO, xxG
India
• models -CTO, xxQ
Israel
• models -CTO, xxG
Italy
• models -CTO, xxG
Korea
• models -CTO, xxK
Switzerland
• models -CTO, xxG
Taiwan
• models -CTO, xxV
U.K., China (Hong Kong S.A.R.)
• models -CTO, xxB, xxG, xxH
Recovery discs
Windows XP Professional DVDs
Windows XP Professional is preinstalled as the operating system in the following models:
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
FRU no.
42T5050 42T5135
CRU
ID
*
42T5056 42T5141
42T5004 42T5089
42T5065 42T5150
42T5041 42T5126
42T5029 42T5114
42T5083 42T5168
42T5062 42T5147
42T5047 42T5132
42T5077 42T5162
42T5044 42T5129
42T5071 42T5156
42T5035 42T5120
Chapter 10
.
Parts list
141
Table 20. Parts list—Windows XP Professional recovery DVDs
Language
French
German
Italian
Japanese
Simplified Chinese
US English
P/N
04T1302
04T1303
04T1304
04T1129
04T1301
04T2728
Windows XP Professional Generic DVDs
Windows XP Professional Generic is preinstalled as the operating system in the following models:
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
Table 21. Parts list—Windows XP Professional Generic recovery DVDs
Language P/N
Brazilian Portuguese
Czech
Danish
Dutch
Finnish
Greek
Hong Kong
Hungarian
Korean
Norwegian
Polish
Portuguese
Russian
Spanish
Swedish
Traditional Chinese
Turkish
03W7476
03W7479
03W7480
03W7490
03W7481
03W7483
03W7485
03W7486
03W7489
03W7491
03W7492
03W7493
03W7494
03W7495
03W7496
03W7478
03W7497
142
Hardware Maintenance Manual
CRU
ID
*
CRU
ID
*
Windows Vista Business (32 bit) DVDs
Windows Vista Business (32 bit) is preinstalled as the operating system in the following models:
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
Table 22. Parts list—Windows Vista Business (32 bit) recovery DVDs
Language P/N
US English
04T1760
CRU
ID
*
Windows Vista Home Basic (32 bit) DVDs
Windows Vista Home Basic (32 bit) is preinstalled as the operating system in the following models:
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
Table 23. Parts list—Windows Vista Home Basic (32 bit) recovery DVDs
Language P/N
US English 04T1761
CRU
ID
*
Windows 7 Home Basic (32 bit) DVDs
Windows 7 Home Basic (32 bit) is preinstalled as the operating system in the following models:
• 7826-CTO, 37x, 38x, 3Cx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Qx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx,
43x, 45x, 46x, 47x, 48x
• 7827-CTO, 5Yx, 5Zx
• 7829-CTO
• 7853-CTO
• 7854-CTO, 47x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 52x, 53x, 55x, 57x, 58x
• 7856-CTO
• 5015-CTO
• 5016-CTO
Chapter 10
.
Parts list
143
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
Table 24. Parts list—Windows 7 Home Basic (32 bit) recovery DVDs
Language
Arabic
Brazil Portuguese
French
Indian English
Portuguese
Serbian-Latin
Simplified Chinese
Spanish
Turkish
US English
Windows 7 Home Premium (32 bit) DVDs
Windows 7 Home Premium (32 bit) is preinstalled as the operating system in the following models:
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
Table 25. Parts list—Windows 7 Home Premium (32 bit) recovery DVDs
Language P/N
Indian English
Simplified Chinese
US English
04T1813
04T1812
04T1814
P/N
04T1802
04T1803
04T1806
04T1805
04T1807
04T1809
04T1804
04T1808
04T1810
04T1811
Windows 7 Home Premium (64 bit) DVDs
Windows 7 Home Premium (64 bit) is preinstalled as the operating system in the following models:
• 7826-CTO
• 7827-CTO, 4Kx
• 7829-CTO, 4Nx, 4Px
• 7853-CTO
CRU
ID
*
CRU
ID
*
144
Hardware Maintenance Manual
• 7854-CTO, 4Jx
• 7856-CTO, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 4Cx, 4Dx
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
Table 26. Parts list—Windows 7 Home Premium (64 bit) recovery DVDs
Language
Arabic
Brazil Portuguese
C&L Croatian (English/Slovenian,/Croatian)
C&L EMEA (Dutch/French/German/Italian/English)
C&L Nordics (Danish/Finnish/Swedish/Norwegian/English)
Czech
French
German
Greek
Hebrew
Hungarian
Japanese
Korean English
Polish
Portuguese
Romanian
Russian
Serbian-Latin
Simplified Chinese
Slovak
Spanish
Traditional Chinese
Traditional Chinese (for Hong Kong S.A.R.)
Turkish
US English
US English disable
P/N
04T1815
04T1816
04T1840
04T1839
04T1838
04T1819
04T1820
04T1822
04T1821
04T1823
04T1825
04T1826
04T1827
04T1828
04T1829
04T1830
04T1831
04T1834
04T1817
04T1832
04T1833
04T1818
04T1824
04T1835
04T1837
04T1836
Windows 7 Professional (32 bit) DVDs
Windows 7 Professional (32 bit) is preinstalled as the operating system in the following models:
• 7826-CTO
• 7827-CTO, 47x, 48x, 4Ax, 4Lx, 55x, 56x, 57x, 58x, 5Dx, 5Ex, 5Fx, 5Vx, 62x, 67x, 68x
• 7829-CTO, 4Cx, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux
CRU
ID
*
Chapter 10
.
Parts list
145
• 7853-CTO
• 7854-CTO, 4Xx, 4Yx, 4Zx, 54x, 56x
• 7856-CTO, 3Nx, 3Px, 3Qx
• 5015-CTO, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx
• 5016-CTO, 42x, 45x, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Vx, 5Wx, 5Xx, 5Yx, 63x, 64x
• 5017-CTO, 42x, 45x
• 5019-CTO
• 7859-CTO, 4Hx, 4Nx, 4Px, 55x, 56x, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Wx, 5Xx, 5Yx, 5Zx, 62x,
63x, 64x, 65x, 66x
• 7860-CTO, 3Lx, 3Mx
Table 27. Parts list—Windows 7 Professional (32 bit) recovery DVDs
Language P/N CRU
ID
* C&L EMEA (Dutch/French/German/Italian/English)
C&L Nordics (Danish/Finnish/Swedish/Norwegian/English)
French
German
Japanese
Simplified Chinese
Spanish
Traditional Chinese (for Hong Kong S.A.R.)
US English
04T1770
04T1769
04T1763
04T1764
04T1766
04T1762
04T1767
04T1765
04T1768
Windows 7 Professional (64 bit) DVDs
Windows 7 Professional (64 bit) is preinstalled as the operating system in the following models:
• 7826-CTO, 35x, 36x, 39x, 3Ax, 3Bx, 3Ex, 3Fx, 3Gx, 49x
• 7827-CTO, 32x, 33x, 34x, 42x, 43x, 44x, 45x, 46x, 49x, 4Cx, 4Dx, 4Fx, 4Gx, 4Hx, 4Jx, 4Mx, 4Nx, 4Px,
4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 59x, 5Ax, 5Bx, 5Cx, 5Gx, 5Hx, 5Jx,
5Kx, 5Lx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Wx, 5Xx, 66x
• 7829-CTO, 32x, 33x, 34x, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx,
4Kx, 4Lx, 4Mx, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx
• 7853-CTO
• 7854-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Lx, 3Nx,
3Px, 3Sx, 3Tx, 3Xx, 3Yx, 3Zx, 42x, 43x, 44x, 45x, 46x, 4Gx, 4Hx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx,
4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 5Ax, 5Cx, 5Dx, 5Ex
• 7856-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Wx, 3Xx, 3Yx, 3Zx, 42x,
43x, 44x, 45x, 48x, 49x, 4Ax
• 5015-CTO, 32x, 33x, 34x, 35x
• 5016-CTO, 32x, 33x, 43x, 44x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx,
4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 55x, 56x, 57x,
58x, 59x, 5Ax, 5Bx, 5Cx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Zx, 62x
• 5017-CTO, 32x, 33x, 43x, 44x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx,
4Lx, 4Mx, 4Px
• 5019-CTO
• 7859-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Hx, 3Jx, 3Kx, 3Lx,
3Mx, 3Px, 3Rx, 3Sx, 3Wx, 3Xx, 3Yx, 3Zx, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx,
4Ex, 4Fx, 4Gx, 4Jx, 4Kx, 4Lx, 4Mx, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 57x,
58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux
146
Hardware Maintenance Manual
• 7860-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Nx,
3Px, 3Qx, 3Rx, 3Sx
Table 28. Parts list—Windows 7 Professional (64 bit) recovery DVDs
Language P/N CRU
ID
* Arabic
Brazil Portuguese
C&L Nordics (Danish/Finnish/Swedish/Norwegian/English)
C&L EMEA (Dutch/French/German/Italian/English)
C&L Croatian (English/Slovenian/Croatian)
Czech
Indian English
French
German
Greek
Hebrew
Hungarian
Japanese
Korean English
Polish
Portuguese
Romanian
Russian
Serbian-Latin
Simplified Chinese
Slovak
Spanish
Traditional Chinese
Traditional Chinese (for Hong Kong S.A.R.)
Turkish
US English
US English disable
04T1771
04T1772
04T1795
04T1796
04T1797
04T1775
04T1776
04T1777
04T1779
04T1778
04T1780
04T1782
04T1783
04T1784
04T1785
04T1786
04T1787
04T1788
04T1791
04T1773
04T1789
04T1790
04T1774
04T1781
04T1792
04T1794
04T1793
Windows 7 Starter (32 bit) DVDs
Windows 7 Starter (32 bit) is preinstalled as the operating system in the following models:
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
Chapter 10
.
Parts list
147
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
Table 29. Parts list—Windows 7 Ultimate (64 bit) recovery DVDs
Language
Indian English
Russian
US English
P/N
04T1841
04T1842
04T1843
Windows 7 Ultimate (32 bit) DVDs
Windows 7 Ultimate (32 bit) is preinstalled as the operating system in the following models:
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
Table 30. Parts list—Windows 7 Ultimate (32 bit) recovery DVDs
Language P/N
Indian English
US English
04T1798
04T1799
Windows 7 Ultimate (64 bit) DVDs
Windows 7 Ultimate (64 bit) is preinstalled as the operating system in the following models:
• 7826-CTO
• 7827-CTO
• 7829-CTO
• 7853-CTO
• 7854-CTO
• 7856-CTO
• 5015-CTO
• 5016-CTO
• 5017-CTO
• 5019-CTO
• 7859-CTO
• 7860-CTO
CRU
ID
*
CRU
ID
*
148
Hardware Maintenance Manual
Table 31. Parts list—Windows 7 Ultimate (64 bit) recovery DVDs
Language
Indian English
US English
Common service tools
Table 32. Parts list—Common service tools
Tool
Screwdriver kit
1/4" drive spinner handle
1/4" Sq. to 1/4" hex torx adapter
TR7-TR-10 tamper resistant torx bits
Removal tool antenna RF connector
USB 2.0 CD-RW/DVD-ROM combo drive II
USB cable
USB floppy diskette drive for maintenance diskette
USB floppy diskette drive tool kit
Test card for integrated Smart Card
LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later
Note: Download the file from the following Web site: http://support.lenovo.com
P/N
04T1800
04T1801
CRU
ID
*
P/N
95F3598
1650840
93F2838
00P6967
08K7159
40Y8687
40Y8704
05K9283
27L3452
42W7820
—
Chapter 10
.
Parts list
149
150
Hardware Maintenance Manual
Appendix A. Notices
Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that
Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead. However, it is the user’s responsibility to evaluate and verify the operation of any other product, program, or service.
Lenovo may have patents or pending patent applications covering subject matter described in this document. The furnishing of this document does not give you any license to these patents. You can send license inquiries, in writing, to:
Lenovo (United States), Inc.
1009 Think Place - Building One
Morrisville, NC 27560
U.S.A.
Attention: Lenovo Director of Licensing
LENOVO PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to you.
This information could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in new editions of the publication.
Lenovo may make improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time without notice.
The products described in this document are not intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. The information contained in this document does not affect or change Lenovo product specifications or warranties. Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or third parties. All information contained in this document was obtained in specific environments and is presented as an illustration. The result obtained in other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of the materials for this Lenovo product, and use of those Web sites is at your own risk.
Any performance data contained herein was determined in a controlled environment. Therefore, the result obtained in other operating environments may vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.
© Copyright Lenovo 2011
151
Electronic emissions notices
For electronic emission information on Class B digital devices, refer to the corresponding information in the User Guide.
Trademarks
The following terms are trademarks of Lenovo in the United States, other countries or both:
Active Protection System
Lenovo
ThinkPad
ThinkVantage
ThinkLight
TrackPoint
UltraNav
The following terms are trademarks of the Microsoft group of companies:
Microsoft
Windows
Windows Vista
The following are trademarks of Intel Corporation or its subsidiaries in the United States, other countries, or both:
Intel
Intel Celeron
Intel Centrino
Intel Core
Intel Pentium
Other company, product, or service names may be the trademarks or service marks of others.
152
Hardware Maintenance Manual
Part Number: 0A60342_03
(1P) P/N: 0A60342_03
*0A60342_03*
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project