manual_D122A V2.0-IECEx_2014
User's manual
Digital Indicator
D122.A
software version 2.0
User’s manual for indicators
D122.A.x.x.x
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
2 Operation instructions
Page 2
Table of contents
1 Operation instruction for Explosion protected device ................................................................4 1.1 2 Safety Measures: to read and to comply ...................................................................................5 Digital Indicator D122.A ..................................................................................................................6 2.1 Short description ........................................................................................................................6 2.2 2.2.1 2.2.2 Features overview......................................................................................................................6 Basic functions ....................................................................................................................6 Options................................................................................................................................6 2.3 Conformity with Standards .........................................................................................................6 2.4 Internal zener barrier option .......................................................................................................7 2.5 Integrated 2-wire transmitter option ...........................................................................................7 2.6 Special software option ..............................................................................................................8 2.7 Curve fitting ................................................................................................................................8 2.8 Square root-fitting ......................................................................................................................8 3 Installation and Connection ...........................................................................................................9 3.1 3.1.1 3.1.2 D122 with control panel housing................................................................................................9 Installation control panel housing .......................................................................................9 Connecting D122 with control panel housing .....................................................................9 3.2 3.2.1 Field housing D122.A.5, D122.A.6 and D122.A.7 ...................................................................10 Connection D122 with field housing .................................................................................10 3.3 Connecting D122A with zener barrier option ...........................................................................12 3.4 Connection with MU option (integrated measuring transducer): .............................................12 3.5 Connecting D122A with limit terminals (terminals 5/6 + 7/8) ...................................................13 3.6 Connection of intrinsically safe ia- current circuits...................................................................13 3.7 3.7.1 3.7.2 Initial operation .........................................................................................................................13 Default parameters ...........................................................................................................13 Ex works settings – Device reset......................................................................................14 4 Operating manual ..........................................................................................................................15 4.1 Front view.................................................................................................................................15 4.2 Keyboard ..................................................................................................................................15 4.3 4.3.1 4.3.2 Configuration ............................................................................................................................16 How to set the parameters ...............................................................................................18 Hysterese and time delay setting .....................................................................................20 4.4 Configuration example .............................................................................................................21 5 Flow charts ....................................................................................................................................24 6 Annex .............................................................................................................................................30 6.1 Specifications ...........................................................................................................................30 6.2 Type code ................................................................................................................................31 6.3 Material specification ...............................................................................................................31 6.4 Marking ....................................................................................................................................32 6.5 Failure messages .....................................................................................................................33 6.6 Transport, Storing, Repairs und Disposal ................................................................................33 Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
2 Operation instructions
Page 3
6.7 Dimensions ..............................................................................................................................34 6.8 List of Parameters ....................................................................................................................36 The symbols WARNING, CAUTION, NOTE
This symbol warns of a serious hazard. Failure to observe this warning may result in death or the destruction of property.
This symbol warns of a possible failure. Failure to observe this caution may result in the total failure of the device or the system or plant
to which it is connected.
This symbol highlights important information.
Grounding terminal.
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
1
2 Operation instructions
Page 4
Operation instruction for Explosion protected device
Application and Standards
This instruction manual applies to explosion-protected control panels of type of protection
types below. This apparatus is only to be used as defined and meets requirements of EN 60
079 particularly EN60 079-14 "electrical apparatus for potentiality explosive atmospheres".
Use this manual in hazardous locations, which are hazardous due to gases and vapours according to the explosion group and temperature class as stipulated on the type label. When
installing and operating the explosion protected distribution and control panels you should observe the respective nationally valid regulations and requirements.
General Instructions
The device has to have a back-up fuse as stipulated. The mains connection must have a sufficient short circuit current to ensure safe breaking of the fuse. To achieve an impeccable and
safety device operation, please take care for adept transportation, storage and mounting, as
well as accurate service and maintenance. Operation of this device should only be implemented by authorised persons and in strict accordance with local safety standards.
The electrical data on the type label and if applicable, the "special conditions" of the test certificate TÜV 99 ATEX 1488 and IECEx TUN 14.0011 are to be observed.
For outdoor installation it is recommended to protect the explosion protected distribution and
control panel against direct climatic influence, e.g. with a protective roof. The maximum ambient temperature is 40°C, if not stipulated otherwise.
Intrinsically Safe Circuits
Erection instructions in the testing certificates of intrinsically safe apparatus are to be observed. The electrical safety values stipulated on the type label must not be exceeded in the
intrinsically safe circuit. When interconnecting intrinsically safe circuits it is to be tested,
whether a voltage and/or current addition occurs. The intrinsic safety of interconnected circuits
is to be ensured. (EN 60079-14, section 12)
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
1.1
2 Operation instructions
Page 5
Safety Measures: to read and to comply
Work on electrical installations and apparatus in operation is generally forbidden in
hazardous locations, with the exception of intrinsically safe circuits. In special cases
work can be done on non-intrinsically safe circuits, on the condition that during the
duration of such work no explosive atmosphere exists. Only explosion protected
certified measuring instruments may be used to ensure that the apparatus is voltage-free. Grounding and short-circuiting may only be carried out, if there is no explosion hazard at the grounding or short circuit connection.
Danger of static charge!
Clean only with humid cloth!
Do not open when an explosive dust atmosphere is present!
The D122 may connected exclusively to an intrinsically safe
4 … 20 mA measuring circuit.
For all types of D122 the maximum values for voltage and
short-circuit current written in the EC-Type examination certificate are valid.
Just for D122.x.x.x.BM
Within hazardous areas an Ex e-box must be used for the connection of the cable.
The evidence of intrinsically safety is not necessary.
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
2 Operation instructions
2
Digital Indicator D122.A
2.1
Short description
Page 6
The digital Indicator D122 indicates measured values of intrinsically safe current circuits from 4 up to
20 mA in hazardous areas. The device is powered by measure current, therefore an extra power supply or batteries are unnecessary. The indicator measures the current, scales the measured value and
displays finally the result on the LCD.
For trend analysis, the measured signal is also be displayed on a 41 segment bargraph. It's possible
to scale the bargraph separately to the digital value. The indicator D122 is available in several housings.
Furthermore with alarm monitoring option the indicator has two intrinsically safe alarm outputs. These
outputs change their state, when the measured value exceeds his alarm limits. It’s possible to choose
open-circuit or closed-circuit connection. These options are not allowed in Zone 21 and 22.
Additional the alarm limits appear graphically on a second bargraph. On one look you’re sure that the
measured value is in its limits.
2.2
Features overview
2.2.1 Basic functions
• Loop-powered digital Indicator
• Connect like passive analogue indicators, voltage drop ca. 1V
• LC-Display up to 50 mm figure-height
• Scale by buttons and display
• Fast bargraph for trend observation (41 segments, refresh 4 times per second)
• Separately scaleable Bargraph (Zoom)
• Several housings available (control panel- and field housing)
2.2.2 Options
• Alarm monitoring: two intrinsically safe alarm outputs and an additional limitbargraph on the display
• Limit-functions with hysteresis and time delay
• Field housing with additional (2nd) PG-Connector
2.3
Conformity with Standards
The explosion proof indicators type D122 meets requirements of listed standards in the attachment
(Declaration of conformity). They were developed, manufactured and tested in accordance with stateof-the-art engineering practice and ISO9001:2008.
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
2.4
3 Installation and Connection
Page 7
Internal zener barrier option
Devices with type code D122.A.x.x.BM
The standard digital indicator D122 works exclusively in intrinsically safe 4..20 mA current circuits (Ex i). If the concerned measure current circuit is not intrinsically safe, an extra zener
barrier or an isolated interface and a long additional cable to the interface outside the hazardous area and back is needed.
In those cases, the option integrated zener barrier
is very practical, because the interface is build in. A
further advantage of an indicator with this option is
that the intrinsical safety proof is not required.
The terminal voltage in the measure circuit with
internal zener barrier option is about 2 V.
2.5
Integrated 2-wire transmitter option
Devices with type code D122.A.x.x.MU
Using the integrated 2-wire transmitter for head mounting option, the D122 has an interface to an arbitrary sensor e.g. a PT 100.
The digital indicator series with field housing can be equipped with a customized intrinsically safe 2wire transmitter for head mounting, according to DIN 43729 type B (max. height = 30 mm). With this
option, it is possible to connect a sensor, e.g., a PT 100 directly to the digital indicator D122.
Customer can specify or provide the desired transmitter by order.
This option is only available for indicators with field housing. The depth of the field housing is increased from 64 to 82 mm.
A combination with the internal zener barrier option is not possible.
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
2.6
3 Installation and Connection
Page 8
Special software option
Indicators D122.AS as well as totalizers D122.ZS have a special software option. With this option, it is
possible to use these devices in any individual cases of measurement and indication.
2.7
Curve fitting
The curve fitting software indicates the measure current in a non-linear way. Consider the application of a filling-level meter for a sphere-tank. The measure current is linear to the filling-height of the
liquid. Nevertheless, the function between the filling-height and the volume is non-linear, as shown in
the figure below.
To get the correct quantity indication you require a list of points, which shows the connection between measure current and associated quantity inside of the tank. The curve fitting software of the
D122.XS interpolates the curve between these points on your choice in a linear or a square way.
The linear interpolation generates imaginary straight lines between the selected points. A
value on this line will be calculated on base of his distance to the previous selected point.
This kind of interpolation requires 17 points to scale 4 up to 20 mA.
On the other hand, the square interpolation needs a list of 33 points, but it approximates
the original curve much better than the linear one, so the error between the original curve
and the interpolated curve is much smaller.
To put in the list of selected point enter the (extended) scale menu. The device displays the measure
current and you have to enter the associated display value. See also related flow diagram.
2.8
Square root-fitting
To program a square root-function, e.g., to display the flow through a aperture, a special square rootfitting feature is available. For this option, it is not necessary to enter a list of points, but just a startand a end-value (in previous example: associated flow by 4 and by 20mA measure current). The device calculates automatically the selected points for interpolation. Be prepared, this procedure will take
some time. See also related flow diagram.
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
3 Installation and Connection
3
Installation and Connection
3.1
D122 with control panel housing
Page 9
3.1.1 Installation control panel housing
The digital indicators D122.A.0 and D122.A.3 are predicated for installation in
a control panel.
How to insert
the dimension
symbol
Insert the dimension symbol (icon) before mounting. Do this by first removing
the front frame as shown in the figure at left. Now remove the front panel
from the housing as shown in the figure on the right.
Cut the desired dimension-symbol from the set and pull it into its intended
place on the right side of the panel. Make sure that the symbol is facing the
front. Replace the front panel and frame.
Fixing
Fix the indicator into the control panel with the intend cramps.
3.1.2 Connecting D122 with control panel housing
Connect the indicator only to intrinsically safe
4..20 mA current circuits.
The terminals of the indicators in the control panel housing are shown in figure 1. The terminals 5,6 and 7,8 are absent by indicators without alarm monitoring.
Please regard the terminal maximum values of the
attached EC- type certificate TÜV 99 ATEX 1488 or
IECEx TUN 14.001.
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
3 Installation and Connection
Intrinsically safe measure circuit 4 ..20 mA
Terminals 1,2
Page 10
Alarm monitoring option
terminals 5,6 low alarm
terminals 7,8 high alarm
Figure 1: Terminals by indicators with control panel housing
3.2
Field housing D122.A.5, D122.A.6 and D122.A.7
When mounting the housing box on a wall, be sure that it is securely supported by anchoring the screws into a stud or other solid surface.
How to insert
the Dimensionsymbol
First, cut the desired dimension symbol out of the set. Then pull off the four
screws of the cap and remove the cap from the housing.
Now push the prepared dimension-symbol into the dimension-symbol-slot.
Make sure that the symbol is facing the front.
The dimension-symbol-slot lies below the display, on the internal side of the
cap.
Finally replace the cup on the housing.
3.2.1 Connection D122 with field housing
The terminals of the indicators with field housing are inside. The placement of
the terminals is shown at the following figures.
Figure 2 shows the terminals of the indicator D122.A.5. Figure 3 shows the
terminals of the indicator D122.A.6 and Figure 3 shows the terminals of the
indicator D122.A.7.
The terminals 5,6 and 7,8 are absent by indicators without alarm monitoring.
Please regard the terminal maximum values of the
attached EC- type certificate TÜV 99 ATEX 1488
and IECEx TUN 14.0011 certificate.
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
3 Installation and Connection
Page 11
Avoid powerful electromagnetic fields during installation in Ex Zones 21 and 22.
Figure 2: Terminals of the indicator D122.A.5
Figure 3: Terminals of the indicator D122.A.6
Figure 4: Terminals of the indicator D122.A.7
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
3.3
3 Installation and Connection
Page 12
Connecting D122A with zener barrier option
Connect the D122.A.x.x.BM to a non intrinsically safe measure signal.
Inside of hazardous area the D122A.x.x.BM cable must be connected in a
certificated Ex e-connection box.
Figure 5: Connection of D122.A.x.x.BM
Cable
colors
3.4
Cable
Connection
Brown
+
Blue
-
Green yellow
PE
Connection with MU option (integrated measuring transducer):
1 2 3 4
5 6 7 8
+ - + UG
OG
PT1 00
9 10
+ -
UHilfs =
13 -30V
Connection diagram in D122
Clamp
Function
1–4
4- cables of PT100
5,6
Option: connection of lower limit value
7,8
Option: connection of upper limit value
9 (+)
Supply voltage Ui = 13-30V intrinsically safe
10 (-)
Supply voltage Ui = 13-30V intrinsically safe
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
3.5
3 Installation and Connection
Page 13
Connecting D122A with limit terminals (terminals 5/6 + 7/8)
Devices with type code D122.x.x.2.x
Figure 6: limit monitoring with D122.x.x.2.x
3.6
Connection of intrinsically safe ia- current circuits
If there is one intrinsically safe ia- current circuit
connected to the D122, all other current circuits
have to be intrinsically safe too.
3.7
Initial operation
After connecting, a display test (all segments of the display are turned on)
appears immediate during one second. Thereupon the display shows the
software version of the indicator.
3.7.1 Default parameters
The following parameters are active ex works:
4 mA curent -> 4.00
Scaling (display and bargraph)
20 mA current -> 20.00
Limits
Low: 4.00 mA / High: 20.00 mA
Hysteresis / Delay
0.10 / 0 sec.
alarm outputs (alarm monitoring)
circuit-opening connection
Code words
CODE1: 0001 / CODE2: 0002
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
3 Installation and Connection
Page 14
3.7.2 Ex works settings – Device reset
Press the Enter- and Right-button during the start sequence to
reactivate the default parameters. (Hardware-Reset)
A reset activates also the ex works calibration.
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
4 Manual
4
Operating manual
4.1
Front view
4.2
Keyboard
Page 15
On the front side of the indicator are tree buttons with several function symbols. With these tree buttons, the user can activate each function and enter all parameters for any individual setting.
The buttons are named by their functions:
Enter-button
Pressing the enter-button starts the input menu.
In general, the enter-button activates the menu item or accepts the manipulated value of a parameter.
Up-button
Functions of the up-button are:
1. current control button
2. modification of the selected figure
3. pass menu items
Right-button
Functions of the right-button are:
1. change the display to limit view
2. select figures
3. pass menu items
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
4.3
4 Manual
Page 16
Configuration
It is easy to set the parameters and change the configuration of the indicator. The parameters are
logically grouped by a menu structure. See also the appropriate flow diagram in the appendix.
Indicators without the alarm monitoring option have not got the
corresponding menu items.
Note flow charts
SET
The Input views in the flow diagrams have additional boxes in
their background, because the Input views may be changed by
pressing any of the buttons.
The procedure, to enter a value, is shown in the flow diagram
‘Value input menu’, see figure .
)
Normal state
After connecting, the indicator D122 starts to initialise its configuration. The configuration data is stored in an internal EEPROM
due to the previous run. By the first start, the D122 indicator initialises the default configuration.
Directly past starting sequence the indicator begins to display the
measured current digital and analogous on the bargraph. This
state is called the ‘normal state’ of the D122 and the indicator is
also ready for inputs.
(See also flow diagram in figure Fehler! Verweisquelle konnte nicht gefunden werden.)
)
current control
Pressing and holding the up-button (current control button) the
display shows the present current and the [mA] symbol.
(See also flow diagram in figure Fehler! Verweisquelle konnte nicht gefunden werden.)
)
limit view menu
(Only for indicators with the alarm monitoring option)
One touch on the right-button starts the limit view menu.
(See also flow diagram in figure 9)
SET
SET
Gönnheimer Elektronic GmbH
The display [limit low] appears on the screen. Press the enterbutton to watch the value of the lower limit.
For passing the low limit press the right-button. The menu changes to the high limit. The screen shows now [limit high]. Confirm
with the enter-button to display the value of the upper limit. Pressing the right-button for a second time quits the limit view menu
and returns to normal state.
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
4 Manual
Page 17
During watching the limit values it is possible to manipulate them
by pressing the enter-button. The view changes to the
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
;
4 Manual
Page 18
Edit mode.
A blinking segment appears below the sign place. Pressing the
right-button selects the figure and the up-button increments the
selected figure. To accept the new limit value, press the enterbutton.
SET
(See also flow diagram in figure )
;
Code protection
Max
Before the menu gets to the edit mode the code 2 must be entered, to prevent a modification by unauthorised persons.
Entering a wrong code word stops the limit view menu immediately.
The default code 2 is [0002].
The interrogation of code 2 can be switched off by modifying
the code 2 to [0000]. For this reason the flow diagram shows the
code interrogation in stroked dots.
4.3.1 How to set the parameters
;
(See also flow diagram in figure Fehler! Verweisquelle konnte nicht gefunden werden.)
Back in the normal state of the indicator we start the
)
Input menu
by pressing the enter-button.
The configuration of the indicator is protected against manipulations by unauthorised persons with the code 1. To get the input menu enter the code 1 default [0001].
It’s impossible to switch off the code 1 interrogation.
After entering the right code word the indicator proposes to join
the
Scale menu. The figure on the left hand appears on the screen.
To scale the measured current, the bargraph and to set the
decimal point join the scale menu by confirming with the enterbutton.
See also flow diagram in figure Fehler! Verweisquelle
konnte nicht gefunden werden.).
To pass the scale menu press the right-button. The following sub
menu is called limit menu. This menu is naturally only available
for indicators with the alarm monitoring option.
In the limit menu the user enters the limits, as well as the hysteresis and the time delay of the alarm outputs.
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
4 Manual
Page 19
(See also flow diagram in figure Fehler! Verweisquelle konnte nicht gefunden werden.)
The next two following items allow to manipulate the words for
code 1 and code 2. The enter-button confirms the input and the
corresponding code appears in edit mode.
Remember that the code word [0000] switches off the code 2.
Max
Finally it’s possible to calibrate the indicator with the following
sub menu called calibration menu.
(See flow diagram in figure Fehler! Verweisquelle
konnte nicht gefunden werden.)
The indicator is already calibrated ex-works.
In general, a further calibration is not necessary and only
experienced persons are allowed to calibrate it. False calibration will result senseless Indication.
To start calibration enter the code word 01234.
Now we reach the end of the input menu. Confirm the end with
the enter-button. The indicator switches back to normal state.
If you want to repeat the input menu, press the right-button.
If an invalid value is entered for any of the parameters, you will
not be able to quit the input menu. Instead, the program switches
automatically into edit mode to the found valid value.
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
4 Manual
Page 20
4.3.2 Hysterese and time delay setting
Hysterese
A hysteretic curve prevents an
unwanted fast switching of the
alarm outputs.
alarm monitoring lower limit
The switching behavior of the low
alarm (min) shows figure Fehler!
Verweisquelle konnte nicht
gefunden werden.. The switching behavior of the high alarm
(max) shows figure Fehler! Verweisquelle konnte nicht gefunden werden..
on
off
measured value
lower limit
Figure 7: Hysteric curve low alarm
alarm monitoring upper limit
hysteresis at upper limit
on
off
measured value
upper limit
Figure 8: Hysteric curve high alarm
Time delay
The span of time ‘te’ is the difference between the first exceeding
of the measurement above the
upper limit and the switching of
the high alarm (For the low alarm
exists an analogous ‘te’).
alarm monitoring upper limit
time delay te
on
off
time
measured value
upper limit
time
moment of first exceeding
Figure 9: Time delay max respectively min
Note
If the measured current falls below the high limit during ‘te’, the tetimer resets.
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
4.4
4 Manual
Page 21
Configuration example
See the following example of a temperature measurement for a
successful parameter input.
o Situation
• desired range: +10°C ... 20°C
• sensor range: -20.0°C ... +30.0°C
o Adjustment
1] Measure range:
-20,00 °C ... + 30,00°C
for 4 ... 20 mA
2] Bargraph:
-5°C ... + 25°C
3] Limits:
lower limit (min): +10°C
upper limit (max.): +20°C
4] Hysterese:
0,5°C low and high limit
5] Alarm monitoring
mode:
circuit-opening connection
6] Time delay:
15 seconds
Procedure:
One touch on the enter-button quits the normal state and starts
the input menu.
The menu interrogates for code 1.
The default code 1 is [0001].
Enter the right code word using the arrow buttons.
Finally hit the enter-button.
;
Scaling display and bargraph:
Join the scale menu pressing the enter-button.
SET
First set the position of the decimal point. The position of the decimal point will be used for each parameter, like display, bargraph
and limits.
Set the decimal point position after the second position, because
we will enter [2000] for the high scale point afterwards.
Fortunately the default setting is on the desired position, so we
can pass the item pressing the right-button.
SET
Gönnheimer Elektronic GmbH
Now the [scale point low] view appears.
Confirm by pressing the enter-button and enter the lower scale
point
(-20°C) as follows:
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
4 Manual
Page 22
Choose the negative sign pressing the up-button.
SET
Touch the right-button to select the first figure.
Now hit the up-button two times ...
SET
SET
... and the figure ‘2’ will be adjusted.
SET
Press the right-button to select the next figure.
SET
Hit the up-button until the figure ‘0’ appears.
Confirm the lower scale point pressing the enter-button. Now
the...
SET
... item appears.
Repeat the input procedure for the upper scale point like the lower scale point. Enter [3000] for the upper scale point.
(Confirm by hitting enter-button)
Enter the upper scale point correct figured ‘as big as possible’
(the first figures should not be ‘0’)
In this case you get most precision of the indicator.
Now scale the bargraph. Hit the enter-button.
SET
SET
Enter [-0500] (-5°C) for the lower bargraph scale point.
Confirm by hitting the enter-button
Enter [2500] (25°C) for the upper bargraph scale point.
Hitting enter-button accepts and quits the scale menu.
;
Limits, Hysteretic curve and time delay
Start limit menu by pressing the enter-button.
SET
Gönnheimer Elektronic GmbH
Press the enter-button for a second time and enter [1000] (10°C)
for the lower limit using the arrow buttons.
Confirm by hitting the enter-button.
(Remember, that the decimal point position is already set)
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
4 Manual
SET
SET
SET
SET
Page 23
Press the enter-button and enter [2000] (20°C) for the upper limit.
Confirm by hitting the enter-button.
To select the hysteresis of the lower limit press the enterbutton.
Now enter [0050] (0,5°C) using the arrow-buttons and confirm
with the enter-button.
To select the hysteresis of the upper limit press the enterbutton.
Now enter [0050] (0,5°C) using the arrow-buttons and confirm
with the enter-button.
Now press enter-button to activate the time delay.
Enter [0015] (15 seconds) for both limits.
SET
Confirm by hitting the enter-button.
SET
SET
Now define the circuit-opening connection first for the low alarm
limit.
Choose the circuit-opening connection [nc---] (normal closed)
using the up-button and confirm by pressing enter-button.
Define the circuit-opening connection for the upper alarm monitor
by the same procedure.
Confirm by hitting the enter-button and quit the limit menu.
We pass simply the following menu items (manipulate code
words and calibrate) using the right-button.
Finally quit the scale menu hitting the enter-button.
The indicator is back in normal state. The changes are immediately active and will be stored after turn off (disconnecting the
indicator).
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
5
5 Flow charts
Page 24
Flow charts
D 122.A
START
Limit view
menu
Min
Max
Input menu
Normal
state
mA
Min
Max
Current
control view
Figure 10: Flow diagram normal state
Figure 11: Flow diagram limit view
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
5 Flow charts
Input
menu
START
Interrogate
code 1
Page 25
false
code
word
Ok
SET
Scale
menu
select
scale menu
SET
Limit
menu
select
limit menu
SET
select
code 1
modify
code 1
SET
modify
code 2
select
code 2
SET
Calibration
menu
select
calibration menu
quit
input menu
Yes
Input
menu
END
No
Figure 12: Flow diagram input menu
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
SET
Scale
menu
END
edit bargraph
high position
select bargraph
high position
SET
edit bargraph
low position
select bargraph
low position
SET
edit high cale point
(20 mA measure cur.)
SET
SET
select
high scale point
SET
edit low scale point
(4 mA measure cur.)
select
low scale point
SET
select decimal
point position
SET
Page 26
Scale
menu
START
SET
SET
5 Flow charts
set position
D122.A
Figure 13: Flow diagram scale menu
edit values enter code
SET
SET
SET
etc.
sign is
selected
second figure
is selected
first figure
is selected
Menu
END
SET
Menu
END
Menu
END
SET
SET
etc.
sign
is modified
second figure
is modified
first figure
is modified
Menu
END
Menu
END
SET
SET
SET
Menu
END
etc.
first figure
is modified
sign
is modified
second figure
is modified
Menu
END
etc.
Menu
END
Menu
END
etc.
etc.
Figure 14: Flow diagram edit mode
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
5 Flow charts
Page 27
Alternative (extended) scale menu for special software option only
Figure 15: Flow diagram extended scale menu
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
5 Flow charts
Page 28
Figure 16: Flow diagram limit menu
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
5 Flow charts
Calibration
menu
START
Interrogate
code
Page 29
false
code
word
Ok
SET
calibration
pass 1
SET
4
mA
order 4 mA
input current
SET
calibration
pass 2
SET
20
mA
order 20 mA
input current
SET
calibration
pass 3
Calibration
menu
END
Figure 17: Flow diagram calibration menu
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
6 Annex
6
Annex
6.1
Specifications
Page 30
D122.A.
D122.A.0
D122.A.3
D122.A.5
D122.A.6
Ex marking
See section 6.4
Certificates
TÜV 99 ATEX 1488 / IECEx TUN 14.0011
Display
Digit height
4½-digit seven-segment LCD
15mm
Display range
30mm
30mm
-19999 ... +19999
D122.A.7
3½
4½
50mm
30 mm
-1999 ...
+1999
-19999 ...
+19999
Dimension symbols
Selectable with defined symbols
Decimal points
Selectable by keyboard
Bargraph
41 segments
/
41 segments
Alarm limits display
Version D122.A.o .2
- Via bargraph
- Flashing 'Max'- or 'Min'- display
/
- per Bargraph
'Max' or 'Min'
Alarm limit monitoring
Version D122.A.o .2
By means of intrinsically safe control circuits (e.g. NAMUR or DIN 19234)
Current control button
Direct display of current in measurement circuit
Measurement circuit
Intrinsically safe measurement circuit 4 ...20 mA; Voltage drop ca. 1V;
Measurement circuit
limits
No-load voltage U i = 65 V; short-circuit current I i = 160 mA
Internal inductance = 40 µH, Internal capacitans = 10 nF
see also certificates: TÜV 99 ATEX 1488 / IECEx TUN 14.0011
Alarm monitoring
limits
By intrinsically safe control circuits
No-load voltage U i = 30 V; Short-circuit current I i = 160 mA;
Pmax not greater than 850 mW; Internal inductance = 40 µH,
Internal capacitance is negligible
see also certificates: TÜV 99 ATEX 1488 / IECEx TUN 14.0011
Housing
Acc. To control-panel standard DIN 43700
Protection class
Front panel IP 40 up to IP 65
Dimensions HxWxD
[mm]
Material
48x96x63,5
72x144x85
Field frame
IP 65
133,5x138x
64
Glass fibre strengthened
Noryl
IP 66
138x184x64
ABS
140 x 140 x 71
Aluminium
Measuring error
0,1% ± 2 digits referring to measure range
Temperature coefficient
< 0,01% of measure range / K
Ambient temperature
limit
-10°C ...+45°C for temperature class 6 or
-10°C ...+60°C for temperature class 5
Indicators for -20°C ambient temperature on inquiry
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
6.2
6 Annex
Page 31
Type code
.
.
Device: Indicator .................................................................. .A
Indicator with curve fitting option ............................. .AS
Totalizer ................................................................... .Z
Totalizer with curve fitting option .............................. .ZS
Transmitter …………………………………………..... .T
Housing:
Control panel housing 48 x 96 mm ......................... .0
Control panel housing 72 x 144 mm ...................... .3
Field housing (30 mm figure height) ...................... .5
Field housing (50 mm figure height) ....................... .6
Field housing 140 x 140mm…………………………. .7
Digital output:
without (II 2 (1) G and II 2 (1) D) .........................
with 2 digital outputs (just II 2 (1) G) ...................
with reset input and pulse output (just II 2 (1) G) .
Additional option:
Device series D122
.
.0
.2
.3
Internal zener barrier1 (just II 2 G) .................................................................. .BM
Internal two wire readings recorder² (just II 2 G) ............................................ .MU
1: Not suitable for D122.x.0.x.x
2: For flied housings only, a combination with internal zener barrier (.BM) is not possible
6.3
Material specification
Device type
Material
manufacturing process
D122.x.0.x.x
D122.x.3.x.x
D122.x.5.x.x
D122.x.6.x.x
D122.x.7.x.x
Noryl
Noryl
ABS
ABS
Aluminum
injection die
injection die
injection die
injection die
die-casting
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
casting
casting
casting
casting
Email: info@goennheimer.de
D122.A
6.4
6 Annex
Page 32
Marking
0044
Type
ATEX
Ex- marking
Ambient temperature
D122.a.7.0.d
a = PA, FF
d = 0, 3K
D122.a.b.0.0
a = A, AS, Z,
ZS, T
b = 0, 3, 5, 6, 7
D122.a.b.c.0
a = A, AS, Z, ZS
b = 0, 3, 5, 6, 7
c = 2, 3, 4
D122.a.b.c.BM
a = A, AS, Z, ZS
b = 3, 5, 6, 7
c = 0, 2, 3, 4
D122.a.b.c.MU
a = A, AS, Z, ZS
b = 5, 6, 7
c = 0, 2, 3, 4
II 2 (1) G
II 2 (1) D
Ex ib [ia Ga] IIC T6 Gb
Ex ib [ia Ga] IIC T5 Gb
Ex ib [ia Da] IIIC T135°C Db
Ex ib [ia Ga] IIC T6 Gb
Ex ib [ia Ga] IIC T5 Gb
Ex ib [ia Da] IIIC T135°C Db
bis 45°C
bis 60°C
bis 60°C
bis 45°C
bis 60°C
bis 60°C
II 2 (1) G
Ex ib [ia Ga] IIC T6 Gb
Ex ib [ia Ga] IIC T5 Gb
bis 45°C
bis 60°C
II 2 G
Ex [ib Gb] ib q IIC T4 Gb
bis 60°C
II 2 (1) G
Ex ib [ia Ga] IIC T6 Gb
Ex ib [ia Ga] IIC T5 Gb
bis 45°C
bis 60°C
II 2 (1) G
II 2 (1) D
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
6.5
6 Annex
Page 33
Failure messages
At startup:
Message
Symptom
Bug-fix
Error 1
Error, general device fault
Turn off an turn on the device, if the fault
remains, send the device back to Gönnheimer
6.6
Transport, Storing, Repairs und Disposal
Transport
Vibration-free in origin package, do not pitch, handle carefully
Storing
Store the device dry, inside of the origin package
Disposal
When the explosion proof multipurpose distribution, switching and control
units are eventually disposed of, the national regulations governing the disposal of waste materials in the country concerned must be rigorously observed.
Defective parts may only be replaced by the Manufacturer or by personnel
specially trained and supervised by the Manufacturer. Only genuine spare
parts from the Manufacturer may be fitted.
Repairs
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
6.7
6 Annex
Page 34
Dimensions
Figure 18: Control panel housing D122.x.0 (D122.x.3)
Figure 19: Field housing D122.x.5
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
6 Annex
Page 35
Figure 20: Field housing D122.x.6
Figure 21: Field housing D122.x.7
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
6.8
6 Annex
Page 36
List of Parameters
The customer is free to use this chart for archiving the parameters of his indicator D122.
Parameter
Description
Previous
Display
Value
Scale menu
Decimalpoint position
dP.PoS
Low scale point
Display at 4 mA input current
SCAL L
High scale point
Display at 20 mA input current
SCAL H
Bargraph low position
Display at starting bargraph
bAr L
Bargraph high position
Display at full bargraph
bAr H
0000
Limit menu
Low limit
LI L
High limit
LI H
Hysteresis of low limit
HYS L
Hysteresis of high limit
HYS H
Alarm connection of low
limit
Choice between normal open (no)
and normal closed (nc)
Con L
nc
no
Alarm connection of high
limit
Choice between normal open (no)
and normal closed (nc)
Con H
nc
no
Code word Nr. 1
CodE 1
Code word Nr. 2
CodE 2
Only on Option
Sondersoftware
Low scale point root function
Display at 4 mA input current
roo L
High scale point root function
Display at 20 mA input current
roo H
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
D122.A
6 Annex
Page 37
Linear resp. square Interpolation
Choice between linear or square
Interpolation
Setpoint
INTER
In 33
In17
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
1100
1150
1200
1250
1300
1350
1400
1450
1500
1550
1600
1650
1700
1800
1850
1900
1950
2000
Gönnheimer Elektronic GmbH
tel: +49(6321)49919-0, fax: -41
Email: info@goennheimer.de
EG-Konformitätserklärung
Declaration of conformity / Déclaration de conformité
Communauté Européenne
Anbieter:
Supplier:
Fournisseur
Gönnheimer Elektronic GmbH
Anschrift:
Address:
Adresse:
Gewerbegebiet Nachtweide
Dr.-Julius-Leber-Straße 2
67433 Neustadt/Weinstraße
Produkt:
Product:
Produit:
D122
Digitales Anzeigegerät / Zähler
Das oben beschriebene Produkt erfüllt die Schutzanforderungen der folgenden EG-Richtlinien / the product
described above complies with the following EG- rules / le produit décrit ci-dessus accomplit CU- réglementations
2004/108/EG, 93/68/EWG, 94/9/EG - ATEX
und ist konform mit / and is in conformity with / et est conforme á:
EN 60079-0:2012 Allgemeine Bestimmungen
EN 60079-5:2007 Sandkapselung „q“
EN 60079-11:2012 Eigensicherheit „i“
EN 61241-1:2004 Schutz durch Gehäuse „tD“
EN 1127-1:2011 ATEX-Grundnorm
EN 61000-6-4: Fachgrundnorm Störaussendung; Teil 6-4: Industriebereich
EN 61000-6-2: Fachgrundnorm Störfestigkeit; Teil 6-2: Industriebereich
EN 60947-1:2008 Niederspannungs-Schaltgeräte
zusätzliche Angaben / additional information / informations supplémentaires:
Qualitätsmanagement- System nach ISO EN DIN 9001:2008
Anerkanntes Qualitätssicherungssystem nach Richtlinie 94/9/EG
Überwachung des QM-Systems durch TÜV- CERT-Zertifizierungsstelle; CE: [0044]
EG- Baumusterprüfbescheinigung / EC- Type certification / Attestation d’examen ce de type
TÜV 99 ATEX 1488
TÜV Nord
Am TÜV 1
30519 Hannover, Germany
Neustadt, den 09.09.2015
Gönnheimer Elektronic GmbH
EG-Konformitätserklärung; Rev.2
Non authorized translation
(1)
EC- TYPE- EXAMINATION CERTIFICATE
(Translation)
(2)
Equipment and protective systems intended for use in
potential explosive Atmospheres – Directive 94/9/EC
(3)
EC- type- examination Certificate number
TÜV 99 ATEX 1488
(4)
Equipment:
Digital Indicator Type D122...
(5)
Manufacturer:
Gönnheimer Elektronic GmbH
(6)
Address:
D-Neustadt an der Weinstraße
(7)
This equipment and any acceptable variation thereto are specified in the schedule to
this certificate and the documents therein referred to.
(8)
The TÜV Hannover/Sachen-Anhalt e.V., TÜV CERT-Zertifizierungsstelle, notified body
No. 0032 in accordance with Article 9 of the Council Directive 94/9/EC of March 1994,
certifies that equipment has been found to comply with the Essential Health and
Safety Requirements relating to the design and construction of equipment and
protective systems intended for use potentially explosive atmospheres, given in Annex
II to the Directive.
The examination and test results are recorded in the confidential report No.
99/PX24090
(9)
Compliance with to essential Health and Safety Requirements has been assured by
compliance with:
EN 50 014:1997 EN 50 020:1994 EN 50 028:1988
(10)
If the sign “X” is places after the certificate number, it indicates that the equipment is
subject to special conditions for safe use specified in the schedule to this certificate.
(11)
This EC- type- examination Certificate relates only to the design and construction of
the specified equipment in accordance with Directive 94/9/EC. Further requirements of
this Directive apply to the manufacture and supply of this equipment.
(12)
The marking of the equipment shall include the following:
II 2 (1) G EEx ia IIC T6 bzw. EEx m [ib] IIC T6
TÜV Hannover/Sachen-Anhalt e.V.
TÜV CERT-Zertifizierungstelle
Am TÜV 1
D-30519 Hannover
Hannover, 02.11.1999
Der Leiter
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only
without alteration. Extracts or alterations are subject to approval by the TÜV Hannover/Sachsen-Anhalt e.V.
Page 1 of 8
Non authorized translation
(13)
SCHEDULE
(14)
(15)
EC- TYPE-Examination CERTIFICATE No. TÜV 99 ATEX 1488
Description of equipment
The digital indicator type D122 ... serves as direct indicator of measured values of
intrinsically safe 4 ..20 mA current circuits in explosive endangered areas.
The maximum ambient temperature is 45°C in temperature class T6 and 60°C in the
temperature class T5.
Electrical details
Supply and
signal current
circuit
(Terminal 1,2)
Exclusive connection to a certificated intrinsically safe
current circuit with the following highest values:
Ui = 65 V
Ii = 160 mA
Effective internal inductivity 40 µH
Effective internal capacity
10 nF
Only Type D122.T.x.x.x
Supply and
signal current
circuit
(Terminal 1,2)
Exclusive connection to a certificated intrinsically safe
current circuit with the following highest values:
Ui = 30 V
Ii = 160 mA
Pi = 1,6 W
Effective internal inductivity 40 µH
effective internal capacity
10 nF
Terminals 3,4
Bridget
Only TYP 122.x.x.x.BM with additional protection type moulding and the sign EEx m
[ib] IIC T6 bzw. EEx m [ib] IIC T5
Input current
circuit (wire)
Um = 250 V and to connect to ground
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only
without alteration. Extracts or alterations are subject to approval by the TÜV Hannover/Sachsen-Anhalt e.V.
Page 2 of 8
Non authorized translation
Schedule EC- Type- Examination Certificate No. TÜV 99 ATEX 1488
Any types
Alarm current
circuits
(Terminal 5,6; 7,8)
Outputs:
Inputs:
Exclusive connection to a certificated intrinsically current
circuit with the following highest values each current circuit:
Ui = 30 V
Ii = 160 mA
Pi = 850 mW
Ui = 30 V
Effective internal inductivity ≤ 40 µH
the effective internal capacity is negligibly small
All current circuits are safe gavanically separated up to a nominal voltage of 90 V to
each other. The input current circuit by the type D122.x.x.x.BM is internally connected
to the supply and signal circuit.
(16)
Report No. 99/PX24090
(17)
Special conditions for safe area
None
(18)
Essential health and safety requirements
No additional
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only
without alteration. Extracts or alterations are subject to approval by the TÜV Hannover/Sachsen-Anhalt e.V.
Page 3 of 8
Non authorized translation
1. Amendment
to
the Conformity Certificate Nr. TÜV 99 ATEX 1488
Manufacturer:
Gönnheimer Elektronic GmbH
Dr.-Julius Leber-Str.2
D-67433 Neuststadt/Weinstraße
The digital indicator type D122 can also be manufactured according to the examination
protocol, listed in the associated examination certificate.
The changes concern the enlargement around the type D122.x.7.x.x. and the application of
type in explosion areas by dust up to ambient temperatures of 65°C. The marking for it is:
II 2 D IP 65 T70°C
Bases of the standards: EN 50281 1 1:1999
The electric data and all other information are valid consistently for this supplement.
The test documentation is listed in test report Nr. 04YEX551218
TÜV NORD CERT GmbH & Co. KG
Hannover, 17.02.2004
TÜV CERT-Zertifizierungsstelle
Am TÜV 1
0-30519 Hannover
Tel.: 0511 986-1470
Fax: 0511 986-2555
Der Leiter
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only
without alteration. Extracts or alterations are subject to approval by the TÜV Hannover/Sachsen-Anhalt e.V.
Page 4 of 8
Non authorized translation
2. Amendment
to
the Conformity Certificate Nr. TÜV 99 ATEX 1488
Manufacturer:
Gönnheimer Elektronic GmbH
Dr.-Julius Leber-Str.2
D-67433 Neuststadt/Weinstraße
The digital indicator type D122 can also be manufactured according to the examination
protocol, listed in the associated examination certificate. The change concerns the
enlargement around the types D122.PA.7.0.0 and D122.FF.7.0.0 for the binding to
intrinsically safe field busses Profibus PA respectively FF.H1.
The application of the supplemental types can occur in explosion-threatened areas,
Which requires devices of the category 2. By the application in areas of explosion-threatened
by dust, the at most allowed ambient temperature is +65°C.
By the application in areas explosion-threatened by gas is the maximum ambient
temperature depending on the temperature class according to the following table:
Temperature classe
T6
T5
Ta
Up to 45°C
Up to 60°C
Electrical data of the types D122.PA.7.0.0 and D122.FF.7.0.0
Signal and power supply circuit
Ex- protection Intrinsically safe EEx ia IIC
(terminal 1,3 and 2,4)
only to the connection in certified intrinsically
safe circuits. Maximum ratings:
U0 = 30 V
I0 = 660 mA
P0 = 1,6 W
max reactances
L0 = 0 µH
C0 = 0 nF
The electrical data remains unchanged.
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only
without alteration. Extracts or alterations are subject to approval by the TÜV Hannover/Sachsen-Anhalt e.V.
Page 5 of 8
Non authorized translation
2. Amendment to the Conformity Certificate Nr. TÜV 99 ATEX 1488
The marking of the equipment:
II 2 (1) G EEx ia IIC T6 or T5; resp. II 2 D IP65 T70°C
The marking of the further types remain unchanged.
The digital indicator type D122... according to the EC-type certificate TÜV 99 ATEX 1488
incl. 1. and this 2nd supplement also fulfils the demands of
EN 50 014 :1997 + A1+A2
EN 50 020:2002
EN 50 281-1-1:1998+A1
General directives
Intrinsically safe “i”
Electrical devices with protection by case construction and check
All remaining data remain unchanged for this 2. Amendment.
The test documentation is listed in test report Nr. 04YEX551692
TÜV NORD CERT GmbH & Co. KG
Hannover, 03.11.2004
TÜV CERT-Zertifizierungsstelle
Am TÜV 1
0-30519 Hannover
Tel.: 0511 986-1470
Fax: 0511 986-2555
Der Leiter
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only
without alteration. Extracts or alterations are subject to approval by the TÜV Hannover/Sachsen-Anhalt e.V.
Page 6 of 8
Non authorized translation
3. Amendment
to certification number:
TÜV 99 ATEX 1488
Device:
Manufacturer:
Digital indicator type D122…
Gönnheimer Elektronic GmbH
Dr.-Julius Leber-Str.2
D-67433 Neuststadt/Weinstraße
Germany
8000553381
10.10.2006
Address:
Order Number:
Date of issue:
Changes:
The digital indicator type D122 can also be manufactured according to the examination
protocol, listed in the associated examination certificate. The change concerns the
enlargement around the types D122.PA.7.0.3K and D122.FF.7.0.3K for the binding to
intrinsically safe field busses Profibus PA respectively FF.H1 as a three channel indicator.
The application of the supplemental types can occur in explosion-threatened areas, which
requires devices of the category 2. By the application in areas of explosion-threatened by
dust, the at most allowed ambient temperature is +65°C.
The information to the allowed ambient temperature is valid consistently accordingly of the
second supplement also for the supplemental types.
The electric data of the second supplement are changed as follows or complemented:
Electric data of the types D122. PA.7.0.0, D122.FF 7.0.0, D122. PA.7.0.3K and
D122.FF.7.0.3K:
Signal and power supply circuit
(terminal 1,3 and 2,4)
By the application in by gas explosionthreatened areas in Ex protection
Intrinsically safe EEx ia IIC.
Field device FISCO to the connection with a
device according to the FISCO model or
Only to the connection in certified
intrinsically safe circuits. Maximum ratings:
U0 = 30 V
I0 = 660 mA
max reactances
L0 = 0 µH
C0 = 0 nF
By the application in by dust explosionthreatened areas max. limit input power
P0 = 1,6 W
The electrical data remains unchanged.
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only
without alteration. Extracts or alterations are subject to approval by the TÜV Hannover/Sachsen-Anhalt e.V.
Page 7 of 8
Non authorized translation
3. Amendment to the Conformity Certificate Nr. TÜV 99 ATEX 1488
The marking of the equipment:
II 2 (1) G EEx ia IIC T6 or T5; resp. II 2 D IP65 T70°C
The marking of the further types remain unchanged.
The digital indicator type D122... according to the EC-type certificate TÜV 99 ATEX 1488
incl. 1. and this 2nd supplement also fulfils the demands of
EN 50 014 :1997 + A1+A2
EN 50 020:2002
EN 50 281-1-1:1998+A1
DIN EN 60079-27:2006
General directives
Intrinsically safe “i”
Electrical devices with protection by case construction and check
Concept for intrinsically safe field bus systems
(FISCO) and concept for non sparking field bus
systems (FNICO)
The test documentation is listed in test report Nr. 06 YEX 553381.
(17)
Special conditions for safe area
None
(18)
Essential health and safety requirements
No additional
TÜV NORD CERT GmbH, Langemarckstraße 20, 45141 Essen, akkreditiert durch die Zentralstelle der Länder für
Sicherheitstechnik (ZLS), Ident. Nr. 0044, Rechtsnachfolger der TÜV NORD CERT GmbH & Co. KG Ident. Nr.
0032
Der Leiter der Zertifizierungstelle
Schwedt
Geschäftsstelle Hannover, Am TÜV 1, 30519 Hannover, Tel.: +49 (0) 511 986-1455, Fax: +49 (0) 511 986-1590
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only
without alteration. Extracts or alterations are subject to approval by the TÜV Hannover/Sachsen-Anhalt e.V.
Page 8 of 8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising