Kenmore 25370813710 Top-Mount Refrigerator Owner's Manual
Advertisement
Advertisement
Use & Care Guide
Manual de Uso y Cuidado
Guide d’utilisation et d’entretien
English / Español / Français
Models/Modelos/Modèles:
253.6081*, 253.7081*
Kenmore
®
Top Mount Refrigerator
Refrigerador Superior
Réfrigérateur à compartiments superposés
* = Color number, número de color, le numéro de couleur
P/N A12823501 (1710)
Sears Brands Management Corporation
Hoffman Estates, IL 60179 U.S.A.
www.kenmore.com
www.sears.com
Sears Canada Inc.
Toronto, Ontario, Canada M5B 2C3 www.sears.ca
®
Record Model/Serial
Numbers
Please read and save these instructions.
This Use & Care Guide provides specific operating instructions for your model. Use your unit only as instructed in this guide.
These instructions are not meant to cover every possible condition and situation that may occur. Common sense and caution must be practiced when installing, operating, and maintaining any appliance.
Please record your model and serial numbers below for future reference. This information is found on the serial plate located inside the refrigerator compartment.
Model Number: 253.
Serial Number:
Purchase Date:
Important Safety
Instructions
Safety Precautions
Do not attempt to install or operate your unit until you have read the safety precautions in this manual. Safety items throughout this manual are labeled with a Danger, Warning, or Caution based on the risk type.
Definitions
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
DANGER
DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
IMPORTANT
Use only soap and water to clean serial plate.
WARNING
WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Table of Contents
Record Model/Serial Numbers ................ 2
Important Safety Instructions ............... 2-4
Warranty Information ............................ 5
Features at a Glance .............................. 6
First Steps ....................................... 7-14
Connecting the Water Supply ................. 15
Setting the Temperature Control ............ 16
Optional Features ........................... 17-19
Food Storage and
Energy-Saving Ideas ........................ 20
Ice Service .......................................... 21
Normal Operating Sounds .................... 22
Care & Cleaning ............................. 23-25
Before You Call .............................. 26-28
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
IMPORTANT
Indicates installation, operation, or maintenance information which is important but not hazard-related.
2
Important Safety Instructions
WARNING
Please read all safety instructions before using your new appliance.
• Refrigerants must be evacuated by a licensed, EPA certified refrigerant technician in accordance with established procedures.
For Your Safety
• Do not store or use gasoline or other flammable liquids in the vicinity of this or any other appliance. Read product labels for warnings regarding flammability and other hazards.
• Do not operate the unit in the presence of explosive fumes.
• Avoid contact with any moving parts of automatic ice maker.
• Remove all staples from the carton.
Staples can cause severe cuts and also destroy finishes if they come in contact with other appliances or furniture.
Child Safety
Destroy or recycle the carton, plastic bags, and any exterior wrapping material immediately after the unit is unpacked.
Children should never use these items to play. Cartons covered with rugs, bedspreads, plastic sheets or stretch wrap may become airtight chambers and can quickly cause suffocation.
WARNING
These guidelines must be followed to ensure that safety mechanisms in this unit will operate properly.
WARNING
Do not attempt to replace LED lights due to high voltage exposure. Call customer service to replace.
Proper Disposal of your Appliance
Risk of child entrapment
Child entrapment and suffocation are not problems of the past. Junked or abandoned appliances are still dangerous – even if they will sit for “just a few days.” If you are getting rid of your appliance, please follow the instructions below to help prevent accidents.
Dispose of refrigerator in accordance with
Federal and Local regulations. Before you throw away your old unit:
• Remove doors.
• Leave shelves in place so children may not easily climb inside.
Electrical Information
• The refrigerator must be plugged into its own dedicated 10 amp, 115 Volt, 60
Hz. AC only electric outlet. The power cord of the appliance is equipped with a three-prong grounding plug for your protection against shock hazards. It must be plugged directly into a properly grounded three-prong receptacle. The receptacle must be installed in accordance with local codes and ordinances. Consult a qualified electrician. Do not use an extension cord or adapter plug.
• Immediately repair or replace any power cord that becomes frayed or damaged.
3
Important Safety Instructions
• Never unplug the refrigerator by pulling on the power cord. Always grip the plug firmly, and pull straight out from the receptacle to prevent damaging the power cord.
• Unplug the refrigerator before cleaning and before replacing a light bulb to avoid electrical shock.
• Performance may be affected if the voltage varies by 10% or more.
Operating the unit with insufficient power can damage the motor. Such damage is not covered under the warranty. If you suspect your household voltage is high or low, consult your power company for testing.
• Do not plug the unit into an outlet controlled by a wall switch or pull cord to prevent the refrigerator from being turned off accidentally.
• Avoid connecting refrigerator to a
Ground Fault Circuit Interruptor (GFCI).
IMPORTANT
CFC/HCFC Disposal
Your old refrigerator may have a cooling system that used CFCs or HCFCs (chlorofluorocarbons or hydrochlorofluorocarbons). CFCs and HCFCs are believed to harm stratospheric ozone if released to the atmosphere. Other refrigerants may also cause harm to the environment if released to the atmosphere.
If you are throwing away your old refrigerator, make sure the refrigerant is removed for proper disposal by a qualified technician. If you intentionally release refrigerant, you may be subject to fines and imprisonment under provisions of environmental legislation.
Grounding type wall receptacle
Do not, under any circumstances, cut, remove, or bypass the grounding prong
Power cord with 3-prong grounded plug
4
Warranty Information
KENMORE LIMITED WARRANTY
FOR ONE YEAR from the date of sale this appliance is warranted against defects in material or workmanship when it is correctly installed, operated and maintained according to all supplied instructions.
WITH PROOF OF SALE, a defective appliance will receive free repair or replacement at option of seller.
For warranty coverage details to obtain free repair or replacement, visit the web page: www.kenmore.com/warranty
This warranty applies for only 90 DAYS from the sale date in the United States, and is void in Canada, if this appliance is ever used for other than private household purposes.
This warranty covers ONLY defects in material and workmanship, and will NOT pay for:
1. Expendable items that can wear out from normal use, including but not limited to filters, belts, bags or screw-in base light bulbs.
2. A service technician to clean or maintain this appliance, or to instruct the user in correct appliance installation, operation and maintenance.
3. Service calls to correct appliance installation not performed by Sears authorized service agents, or to repair problems with house fuses, circuit breakers, house wiring, and plumbing or gas supply systems resulting from such installation.
4. Damage to or failure of this appliance resulting from installation not performed by Sears authorized service agents, including installation that was not in accord with electrical, gas or plumbing codes.
5. Damage to or failure of this appliance, including discoloration or surface rust, if it is not correctly operated and maintained according to all supplied instructions.
6. Damage to or failure of this appliance, including discoloration or surface rust, resulting from accident, alteration, abuse, misuse or use for other than its intended purpose.
7. Damage to or failure of this appliance, including discoloration or surface rust, caused by the use of detergents, cleaners, chemicals or utensils other than those recommended in all instructions supplied with the product.
8. Damage to or failure of parts or systems resulting from unauthorized modifications made to this appliance.
9. Service to an appliance if the model and serial plate is missing, altered, or cannot easily be determined to have the appropriate certification logo.
Disclaimer of implied warranties; limitation of remedies
Customer’s sole and exclusive remedy under this limited warranty shall be product repair or replacement as provided herein. Implied warranties, including warranties of merchantability or fitness for a particular purpose, are limited to one year on the appliance and five years on the sealed system, or the shortest period allowed by law. Seller shall not be liable for incidental or consequential damages. Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, or limitation on the duration of implied warranties of merchantability or fitness, so these exclusions or limitations may not apply to you.
This warranty applies only while this appliance is used in the United States or
Canada*.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
* In-home repair service is not available in all Canadian geographical areas, nor will this warranty cover user or servicer travel and transportation expenses if this product is located in a remote area (as defined by Sears Canada Inc.) where an authorized servicer is not available.
Sears Brands Management Corporation, Hoffman Estates, IL 60179
Sears Canada Inc., Toronto, Ontario, Canada M5B 2C3
5
Features At A Glance
Ice Maker
Ice Bucket
Freezer Shelf
Auxiliary Freezer
Control
Refrigerator
Control
Deli Drawer
Cover
Features may vary according to model
Ice Tray
Full Shelf
Fixed Door
Bin
Door Rack
Dairy Door
Crisper
Cover
Door Rack
Toe Grille
IMPORTANT
Cleaning your Refrigerator
Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Rinse with warm water and dry with a soft cloth.
Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator.
After you remove all of the package materials, clean the inside of your refrigerator before using it. See the “Care & Cleaning” section in this manual.
See important information about cleaning glass shelves and covers in the “Optional
Features” section of this manual.
IMPORTANT
Moving your Refrigerator
Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage.
Always pull the refrigerator straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move it as floor damage could occur.
6
First Steps
This Use & Care Guide provides general operating instructions for your model. Use the refrigerator only as instructed in this
Use & Care Guide. Before starting the refrigerator, follow these important first steps.
Location
• Choose a place that is near a grounded electrical outlet. Do not use an extension cord or an adapter plug.
• If possible, place the refrigerator out of direct sunlight and away from the range, dishwasher or other heat sources.
• The refrigerator must be installed on a floor that is level and strong enough to support a fully loaded refrigerator.
• Consider water supply availability for models equipped with an automatic ice maker. If you do not hook up water to the refrigerator, remember to turn the ice maker off.
Do not block the toe grille on the lower front of your refrigerator. Sufficient air circulation is essential for the proper operation of your refrigerator.
NOTE
CAUTION
Installation
Installation clearances
• Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections:
Sides & Top
Back
⅜ inch
1 inch
NOTE
If your refrigerator is placed with the door hinge side against a wall, you may have to allow additional space so the door can be opened wider.
Guidelines for final positioning of your refrigerator:
• All four corners of the cabinet must rest firmly on the floor.
• The cabinet should be level at the front and rear.
• The sides should tilt ¼-inch (6 mm) from front-to-back (to ensure that doors close and seal properly).
• Doors should align with each other and be level.
To install the toe grille:
1. The toe grille is packaged with the covers installed. Remove the cover on the side corresponding with the door hinge bracket.
For additional instructions on garage installation, refer to “Setting the
Temperature Controls” section.
7
First Steps
2. Attach toe grille to cabinet.
3 Use adjustable wrench to adjust leveling screws. Lower the leveling screws on each side clockwise until they contact the floor (Figure 3). Do not raise the cabinet more than 9 / 16 inch.
9/16"
(14 mm)
Max or
Raise
Figure 3
(some models)
NOTE
In case of future door reversals, save the toe grille cover not being used.
To level the cabinet:
1 Remove the toe grille.
2 Use a flat-blade screwdriver or ⅜ inch socket wrench to raise or lower the front rollers (Figure 2). Do not raise the cabinet more than 9 / 16 inch.
NOTE
Raise the front of the refrigerator enough so the doors close freely when opened halfway. The refrigerator should slope ¼ inch to ½ inch from front-to-back. Then level the refrigerator from side-to-side.
9/16"
(14 mm)
Max
Figure 2 or
Raise
8
First Steps
Tools Necessary: Adjustable
Wrench or
Phillips TM Head Socket
Wrench Set
Top Hinge
Cover Front
Screw
Top Hinge
Cover Rear
Screw or
3/8" Fixed
Wrench
Top
Screw Hinge
Screw
NOTE
The direction in which your refrigerator doors open (door swing) can be reversed, from left to right or right to left, by moving the door hinges from one side to the other. Reversing the door swing should be performed by a qualified person.
IMPORTANT
Before you begin, turn the refrigerator temperature control to “0” (Mechanical controls) or “OFF” (Electronic controls) and remove the electrical power cord from the wall outlet.
Remove any food from door shelves.
Door removal and reversal instructions:
1. Remove toe grille.
2. Remove top hinge cover. Trace around the hinge with a soft lead pencil. This makes reinstallation easier. Remove top hinge and lift door off center hinge pin. Set door aside.
4. Lift refrigerator door off of bottom hinge and set aside.
5. Remove center hinge and shim by removing inside screw and loosening two outside screws enough to allow hinge and shim to slide out. Tighten screws.
6. Loosen two outside screws on opposite side of refrigerator, remove inside screw and install center hinge.
Top
Hinge
Cover
Shim
Washer
Pin
Top Hinge
Screws
3. Unscrew center hinge pin using adjustable wrench and save for reassembly. Ensure plastic washer stays on hinge pin.
9
First Steps
7. Remove three screws on bottom hinge and anti-tip bracket (if equipped) with ⅜” socket wrench.
8. Remove toe grille support and screws
(if equipped).
9. Install bottom hinge and anti-tip bracket (if equipped) on opposite side with the three screws removed from step 7.
10. Unscrew bottom hinge pin using adjustable wrench. Move hinge pin to other hole in hinge and tighten with adjustable wrench.
the thickest part between the doors on the handle side approximately 3 inches from the outside edge. This will ensure proper spacing.
Washer
Screws
19. Tighten the top hinge screws and check door gasket for open seal condition (gap between gasket and cabinet flange).
11. Install toe grille support and screws on opposite side (if equipped).
12. Reverse door handles (see Handle
Installation section).
13. Move freezer and refrigerator door stops to opposite side. Before starting screws, use an awl to puncture the foam.
14. Position refrigerator door onto bottom hinge pin and screw center hinge pin through center hinge into top of door.
Close refrigerator door to help align hinge hole.
15. Tighten center hinge pin with adjustable wrench.
16. Remove cabinet and hinge hole plugs and move to opposite side.
17. Lower freezer door onto center hinge pin.
18. Close freezer door. Lift up on handle side of door and grasp the thinnest part of the top hinge cover (which was removed in Step 2) and insert
10
First Steps
20. Should open seal condition exist, try to massage the gasket to make sure it is seated into the channel.
22. Remove the toe grille cover corresponding with the door hinge bracket from the toe grille and attach the opposite toe grille cover that was saved earlier over the opening on the side corresponding with the toe grille support. (See Figures A & B.)
Toe Grille Cover
A
IMPORTANT
If the condition still exists, try heating the gasket with a hair dryer with the door closed. Use Caution and be careful not to damage the interior door panel or gasket by applying too much heat.
21. If the open seal condition still exists, it may be necessary to flip the gasket.
In this case, remove the gasket from the door by pulling it out. Rotate the gasket half a turn (180 degrees).
Reinstall the gasket by inserting the corners first then work towards the middle assuring that it is fully seated in the channel.
B
23. Reinstall toe grille with appropriate cover (some models).
24. Plug in electrical power cord and turn refrigerator temperature control to center position. Adjust setting as necessary.
11
First Steps
Handle Installation/Removal
CAUTION
Wear gloves and use extreme
CAUTION when installing these handles. The rounded end of the handles may be sharp.
IMPORTANT
To ensure proper installation of handles, please review these instructions and illustrations thoroughly prior to installing the handles.
Additionally, before installing the door handles, make sure the door swing is correct. Your model will have either a right hand or left hand door swing.
Follow instructions in the Use & Care
Guide to reverse the doors, if necessary.
Handle Style 1
To remove refrigerator handle:
(Handles may be easier to reverse while doors are off.)
1. Remove two screws attaching handle to top of refrigerator door.
2. Slide handle straight up and pull handle off mounting screw on door.
3. Remove mounting screw from door and install on other side, moving hole plugs from corresponding holes to opposite side.
To attach refrigerator handle:
1. Place top of handle over mounting screw; pull handle straight down until handle is aligned with screw holes on top of door.
2. Secure top of handle with two screws removed earlier.
To remove freezer handle:
(Handles may be easier to reverse while doors are off.)
1. Remove two screws attaching handle to bottom of freezer door.
2. Slide handle straight down and pull handle off mounting screw on door.
3. Remove mounting screw from door and install on other side, moving hole plugs from corresponding holes to opposite side.
4. Self-Adhesive Nameplate Models:
Use plastic putty knife to gently peel off nameplate from door and reapply over old holes.
12
First Steps
To attach freezer handle:
1. Place top of handle over mounting screw; pull handle straight up until handle is aligned with screw holes on bottom of door.
2. Secure bottom of handle with two screws removed earlier.
Handle Style 2
To remove refrigerator metal handle:
1. Loosen the set screw on the rounded part of the handle.
2. Remove the 2 screws from the top of the handle.
3. Remove rounded part of handle from mounting screw on face of door.
To attach refrigerator metal handle:
1. Place rounded part of handle onto mounting screw on face of door and align the 2 holes in top of handle with the 2 holes in top of door. Handle should be mounted with set screw facing towards center of door. Do not tighten the set screw yet.
2. Install the 2 screws into the top of the handle.
3. Tighten the set screw on the rounded part of the handle until the handle is flush with the door, and then tighten another ½ turn.
Screw
Handle
To reverse refrigerator/freezer handles:
Handles may be easier to reverse while doors are off.
Reverse freezer and refrigerator handles by inverting the handle removed from the refrigerator door and attaching to the freezer door. Invert the handle removed from freezer door and attach to the refrigerator door.
To remove freezer handle:
1. Loosen the set screw on the rounded part of the handle.
2. Remove the 2 screws from the bottom of the handle.
3. Remove rounded part of handle from mounting screw on face of door.
13
First Steps
To attach freezer handle:
1. Place rounded part of handle onto mounting screw on face of door and align the 2 holes in bottom of handle with the 2 holes in bottom of door.
Handle should be mounted with set screw facing towards center of door.
Do not tighten the set screw yet.
2. Install the 2 screws into the bottom of the handle.
3. Tighten the set screw on the rounded part of the handle until the handle is flush with the door, and then tighten another ½ turn.
Mounting
Screw
Set
Screw
Nameplate
Handle
Screw
To reverse refrigerator/freezer handles:
Handles may be easier to reverse while doors are off.
Reverse freezer and refrigerator handles by inverting the handle removed from the refrigerator door and attaching to the freezer door. Invert the handle removed from freezer door and attach to the refrigerator door.
14
Connecting Household Water Supply To Refrigerator
WARNING
To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from electrical power before connecting a water supply line to the refrigerator.
CAUTION
To Avoid Property Damage:
• Copper tubing is recommended for the water supply line. Water supply tubing made of ¼” plastic is not recommended since it greatly increases the potential for water leaks. Manufacturer nor retailer will be responsible for any damage if plastic tubing is used for supply line.
• DO NOT install water supply tubing in areas where temperatures fall below freezing.
• Chemicals from a malfunctioning softener can damage the ice maker.
If the ice maker is connected to soft water, ensure that the softener is maintained and working properly.
IMPORTANT
Ensure that your water supply line connections comply with all local plumbing codes.
Before installing the water supply line, you will need:
• Basic Tools: adjustable wrench, flat-blade screwdriver, and Phillips screwdriver
• Access to a household cold water line with water pressure between 30 and 100 psi.
• A water supply line made of ¼” (6.4 mm)
OD, copper tubing. To determine the length of copper tubing needed, you will need to measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown).
• A shutoff valve to connect the water supply line to your household water system. DO
NOT use a self-piercing type shutoff valve.
• Do not re-use compression fitting or use thread seal tape.
• A compression nut and ferrule (sleeve) for connecting the water supply line to the ice maker inlet valve.
NOTE
A water line kit is available from Sears stores or Sears Parts & Repair at an additional cost.
To Connect Water Supply Line To Ice
Maker Inlet Valve:
1. Disconnect refrigerator from electric power source.
2. Place end of water supply line into sink or bucket. Turn ON water supply and flush supply line until water is clear. Turn
OFF water supply at shutoff valve.
3. Unscrew plastic cap from water valve inlet and discard cap.
4. Slide brass compression nut, and then ferrule (sleeve) onto water supply line, as shown.
5. Push water supply line into water valve inlet as far as it will go (¼”). Slide ferrule (sleeve) into valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT overtighten.
6. With steel clamp and screw, secure water supply line to rear panel of refrigerator as shown.
7. Coil excess water supply line (about 2½ turns) behind refrigerator as shown and arrange coils so they do not vibrate or wear against any other surface.
8. Turn ON water supply at shutoff valve and tighten any connections that leak.
9. Reconnect refrigerator to electrical power source.
10. To turn ice maker on, lower wire signal arm (see ice maker front cover for ON/
OFF position of arm).
Valve Inlet
Water Valve
NOTE
These instructions do not cover after market installation. Instructions in after market ice maker kit should be used.
15
Setting the Temperature Controls
NOTE
When first turning refrigerator on, adjust control to Recommended. This is the recommended initial setting. After
24 hours, adjust the controls as needed.
Do we need to reduce this graphic to only include the controls section?
Is this a vent or a display screen?
Refrigerator Controls
NOTE
If your unit is in a garage or area where the temperature is below 55°F, adjust the freezer control to the coldest setting to improve performance.
Temperature Adjustment
• Adjust temperature gradually: adjust the dial in small increments, allowing the temperature to stabilize.
• For colder temperatures, adjust the dial towards Coldest.
• For warmer temperatures, adjust the dial towards Cold.
IMPORTANT
Adjusting the refrigerator temperature control to “0” turns off the compressor and prevents the refrigerator from cooling, but does not disconnect the power to the light bulb and other electrical components. To turn off power to your refrigerator, you must unplug the power cord from the wall outlet.
Auxiliary Freezer Control
You may want to set the freezer to be colder or less cold than results obtained from the Refrigerator control setting.
Push the freezer control slide up in small increments toward coldest or down toward cold. Adjusting the freezer control will also change the temperature in the refrigerator compartment. Adjusting toward coldest will raise and toward cold will lower the refrigerator compartment temperature.
To maintain temperatures, a fan circulates air in the refrigerator and freezer compartments. For good circulation, do not block cold air vents with food items.
16
IMPORTANT
Adjusting the refrigerator/freezer temperature control to “off” turns off the compressor and prevents the refrigerator from cooling, but does not disconnect the power to the light bulb and other electrical components. To turn off power to your refrigerator, you must unplug the power cord from the wall outlet.
Optional Features
CAUTION
Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small, pebble-size pieces.
This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.
Shelf Adjustment
Refrigerator shelves are easily adjusted to suit individual needs. Before adjusting the shelves, remove all food.
To adjust sliding shelves:
1. Remove shelf by pulling forward to stop position.
2. Lift front edge up and pull out.
To replace shelf, rest side edges on any pair of shelf rails and carefully push shelf back into position.
Sliding Glass Shelf
To adjust slide-under/ flip shelf:
1. Pull front half shelf forward until its back drops down, then
2
1
Slide-Under/Flip Shelf gently push front half shelf back and under back half shelf.
2. With front half fully below back half, lift front of shelf to flip it upwards toward the back of the cabinet.
Door storage
Door bins, shelves, and racks are provided for convenient storage of jars, bottles, and cans.
Frequently used items can be quickly selected.
The dairy compartment, which is warmer than the general food storage section, is intended for short term storage of cheese, spreads, or butter.
Door rack
Some models have door racks or bins that can accommodate gallon-sized plastic drink containers and economy-sized jars and containers.
To remove door rack:
1. Push on rack sides to release from locking tabs.
2. Pull straight out.
To install door rack:
Door Rack
1. Push rack straight ahead.
2. You will hear the sides lock into the tabs.
Sliding Wire Shelf
17
Optional Features
Adjustable door bins (some models)
Some models have adjustable door bins that can be moved to suit individual needs.
To move door bin along a rail:
1. Tilt bin up so the back of the bin is off the door but the hook is still engaged.
2. Slide bin along rail to desired position.
3. Lower bin back into place.
To move door bin from rail to rail:
1. Lift bin up disengaging the hook.
2. Move bin to desired rail location.
3. Push bin hook into rail engaging the hook.
Crisper Humidity Control (some models)
The crisper humidity control, present on the crisper drawers of some models, allows you to adjust the humidity within the crisper. This can extend the life of fresh vegetables that keep best in high humidity.
Low
Humidity
High
Humidity
Higher Humidity Lower Humidity
NOTE
Leafy vegetables keep best when stored with the Humidity Control set on High
Humidity, or in a drawer without a
Humidity Control. This keeps incoming air to a minimum and maintains maximum moisture content. Store nonleafy vegetables and fruits still in their skins at the low humidity setting.
18
Optional Features
Pantry Drawer (some models)
Some models are equipped with a Pantry
Drawer for storage of luncheon meats, spreads, cheeses, and other deli items.
Please be sure to support glass when removing the drawer.
Store-More Drawer (some models)
The Store-More Drawer is located at the top of the refrigerator cabinet directly under the freezer.
To install the Store-More Drawer:
1. Fully extend drawer slides. Position rear upper side tabs into slide clip pockets on both sides. This positions the front drawer cut outs over the slide front tabs that are prefitted to the slides.
Pocket on
"Clip"
Crispers (some models)
The crispers, located under the bottom refrigerator shelf, are designed for storing fruits, vegetables, and other fresh produce. Wash items in clear water and remove excess water before placing them in the crispers. Items with strong odors or high moisture content should be wrapped before storing.
2. Apply pressure to drawer while supporting slide from below. Tab/clip passes through opening in drawer to locate. Ensure both sides are engaged.
Clip Passes Through Opening
3. For removal, hold slide with one hand and lift drawer with the other to separate.
Slide Drawer
19
NOTE
Specific detail of front clip may vary by model.
Food Storage & Energy Saving Ideas
Food storage Ideas
Fresh Food Storage
• The fresh food compartment should be kept between 34°F and 40°F with an optimum temperature of 37°F.
• Avoid overcrowding the refrigerator shelves. This reduces the circulation of air around the food and results in uneven cooling.
Fruits and Vegetables
• Storage in the crisper drawers helps preserve the fruit and vegetable quality for longer time periods.
Meat
• Raw meat and poultry should be wrapped securely so leakage and contamination of other foods or surfaces does not occur.
Frozen Food Storage
• The freezer compartment should be kept at 0°F or lower.
• A freezer operates most efficiently when it is at least ⅔ full.
Packaging Foods for Freezing
• To minimize dehydration and quality deterioration, use aluminum foil, freezer wrap, freezer bags or airtight containers. Force as much air out of the packages as possible and seal them tightly. Trapped air can cause food to dry out, change color, and develop an off flavor (freezer burn).
• Wrap fresh meats and poultry with suitable freezer wrap prior to freezing.
• Do not refreeze meat that has completely thawed.
Loading the Freezer
• Avoid adding too much warm food to the freezer at one time. This overloads the freezer, slows the rate of freezing, and can raise the temperature of frozen foods.
• Leave a space between the packages, so cold air can circulate freely, allowing food to freeze as quickly as possible.
• Avoid storing hard-to-freeze foods such as ice cream and orange juice on the freezer door shelves. These foods are best stored in the freezer interior where the temperature varies less.
Energy saving ideas
• Locate the refrigerator in the coolest part of the room, out of direct sunlight, and away from heating products or registers.
Do not place the refrigerator next to heat-producing appliances such as a range, oven, or dishwasher. If this is not possible, a section of cabinetry or an added layer of insulation between the two appliances will help the refrigerator operate more efficiently.
• Level the refrigerator so that the doors close tightly.
• Refer to this Use & Care Manual for the suggested temperature control settings.
• Periodic cleaning of the condenser will help the refrigerator run more efficiently. See the Care and Cleaning
Chart.
• Do not overcrowd the refrigerator or block cold air vents located at upper rear of refrigerator compartment. Doing so causes the refrigerator to run longer and use more energy.
• Cover foods and wipe containers dry before placing them in the refrigerator.
This cuts down on moisture build-up inside the unit.
• Organize the refrigerator to reduce door openings. Remove as many items as needed at one time and close the door as soon as possible.
20
Ice Service
If your refrigerator has an automatic ice maker, it will provide a sufficient supply of ice for normal use. During the initial startup of your refrigerator, however, no ice will be produced during the first 24 hours of operation. Air in new plumbing lines may cause the ice maker to cycle two or three times before making a full tray of ice. With no usage, it will take approximately one to two days to fill the ice container.
IMPORTANT
Your ice maker is shipped from the factory with the wire signal arm in the ON position.
To ensure proper function of your ice maker, hook up water supply immediately or turn ice maker OFF by lifting the wire signal arm until it clicks and locks in the UP position.
If the ice maker is not turned off and the water supply is not connected, the water valve will make a loud chattering noise.
New plumbing connections may cause the first production of ice cubes to be discolored or have an odd flavor. Discard ice made during the first 24 hours.
Ice Production: What To Expect
The ice maker will produce 2 to 3 pounds of ice every 24 hours depending on usage conditions. Ice is produced at a rate of 8 cubes every 75 to 160 minutes.
NOTE
Automatic ice makers are also optional accessories that may be installed in most models at any time.
“down” or ON position.
Call 1-844-553-6667 for information.
Turning your ice maker on
After the plumbing connections have been completed, the water supply valve must be opened. Place the ice container under the ice maker, pushing it as far back as possible. Lower the wire signal arm to its
Turning your ice maker off
To stop the ice maker, lift the wire signal arm until it clicks and locks
OFF
ON in the “up” or OFF position.
The ice maker also turns off automatically when the ice container is full. If your model has an adjustable freezer shelf, place the shelf in the lower position, so that the wire signal arm will hit the ice when the container is full.
CAUTION
Ice Maker Tips
• Ice cubes stored too long may develop an odd flavor. Empty the ice container and ensure that the wire signal arm is in its “down” or ON position. The ice maker will then produce more ice.
• Occasionally shake the ice container to keep ice separated.
•
•
Chemicals from a malfunctioning softener can damage the ice maker.
If the ice maker is connected to soft water, ensure that the softener is maintained and working properly.
Stop the ice maker when cleaning the freezer and during vacations.
If the ice maker will be turned off for a long period of time, turn the water supply valve to a closed position.
NOTE
For information on ice maker noises, see
Normal Operating Sounds
CAUTION
DO NOT place the ice container in your dishwasher. section.
21
• Wash the ice container in warm water with mild detergent. Rinse well and dry.
Normal Operating Sounds
Understanding the sounds you may hear
Your new, high-efficiency refrigerator may introduce unfamiliar sounds. These sounds normally indicate your refrigerator is operating correctly. Some surfaces on floors, walls, and kitchen cabinets may make these sounds more noticeable.
NOTE
Rigid foam insulation is very energy efficient, but is not a sound insulator.
Following is a list of major components in your refrigerator and the sounds they can cause:
A Evaporator Refrigerant through the evaporator may create a boiling or gurgling sound.
B Evaporator fan You may hear air being forced through the refrigerator by the evaporator fan.
C Defrost heater During defrost cycles, water dripping onto the defrost heater may cause a hissing or sizzling sound. After defrosting, a popping sound may occur.
A
IMPORTANT
During the automatic defrost cycle, you may notice a red glow in the vents on the back wall of your freezer compartment.
This is normal during the defrost cycle.
B
C
H
D
F
J
G
E
I
D Automatic ice maker When ice has been produced, you will hear ice cubes falling into the ice bin.
E Automatic defrost control These parts can produce a snapping or clicking sound when turning the cooling system on and off. Control box may differ from the one shown.
F Condenser fan You may hear air being forced through the condenser.
G Compressor Modern, high-efficiency compressors run much faster than in the past. The compressor may have a high-pitched hum or pulsating sound.
H Water valve If your refrigerator is equipped with an automatic ice maker, you will hear a buzzing sound as the water valve opens to fill the ice maker during each cycle.
I Drain pan (not removable) You may hear water dripping into the drain pan during the defrost cycle.
J Condenser May create minimal sounds from forced air.
22
Care & Cleaning
Protecting Your investment
Keeping your refrigerator clean maintains appearance and prevents odor build-up.
Wipe up any spills immediately and clean the freezer and fresh food compartments at least twice a year. When cleaning, take the following precautions:
• Never use CHLORIDE or cleaners with bleach to clean stainless steel.
• Do not wash any removable parts in a dishwasher.
• Always unplug the electrical power cord from the wall outlet before cleaning.
• Remove adhesive labels by hand. Do not use razor blades or other sharp instruments which can scratch the appliance surface.
• Do not remove the serial plate.
Do not use abrasive cleaners such as window sprays, scouring cleansers, brushes, flammable fluids, cleaning waxes, concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior doors, gaskets or cabinet liners. Do not use paper towels, metallic scouring pads, or other abrasive cleaning materials or strong alkaline solutions.
NOTE
If you set your temperature controls to turn off cooling, power to lights and other electrical components will continue until you unplug the power cord from the wall outlet.
IMPORTANT
If you store or move your refrigerator in freezing temperatures, be sure to completely drain the water supply system. Failure to do so could result in water leaks when the refrigerator is put back into service. Contact a service representative to perform this operation.
CAUTION
Pull the refrigerator straight out to move it. Shifting it from side to side may damage flooring. Be careful not to move the refrigerator beyond the plumbing connections.
Damp objects stick to cold metal surfaces. Do not touch refrigerated surfaces with wet or damp hands.
23
Care & Cleaning
Care & Cleaning Tips
Part What To Use Tips and Precautions
Interior &
Door Liners
• Soap and water
• Baking soda and water
Use 2 tablespoons of baking soda in 1 quart of warm water. Be sure to wring excess water out of sponge or cloth before cleaning around controls, light bulb or any electrical part.
Door Gaskets • Soap and water Wipe gaskets with a clean soft cloth.
Drawers &
Bins
Glass
Shelves
• Soap and water
• Soap and water
• Glass cleaner
• Mild liquid sprays
Use a soft cloth to clean drawer runners and tracks.
Allow glass to warm to room temperature before immersing in warm water.
Toe Grille
Exterior &
Handles
Exterior &
Handles
(Stainless
Steel Models
Only)
• Soap and water
• Mild liquid sprays
• Vacuum attachment
• Soap and water
• Non Abrasive
Glass Cleaner
• Soap and water
• Stainless Steel
Cleaners
Vacuum dust from front of toe grille. Remove toe grille (see Installation Instructions). Vacuum backside, wipe with sudsy cloth or sponge. Rinse and dry.
Do not use commercial household cleaners containing ammonia, bleach or alcohol to clean handles. Use a soft cloth to clean smooth handles.
DO NOT use a dry cloth to clean smooth doors.
Never use CHLORIDE or cleaners with bleach to clean stainless steel.
Clean stainless steel front and handles with nonabrasive soapy water and a dishcloth. Rinse with clean water and a soft cloth. Use a non-abrasive stainless steel cleaner. These cleaners can be purchased at most home improvement or major department stores. Always follow manufacturer’s instructions. Do not use household cleaners containing ammonia or bleach.
Replacing
Light Bulbs
• Unplug refrigerator
• Wear gloves
• Remove light cover (some models)
• Replace old bulb
• Replace light cover (some models)
• Plug in the refrigerator
LED Bulbs • Call customer service to replace
NOTE: Always clean, wipe and dry with the grain to prevent scratching. Wash the rest of the cabinet with warm water and mild liquid detergent. Rinse well, and wipe dry with a clean soft cloth.
CAUTION : Wear gloves when replacing light bulbs to avoid getting cut. Use same wattage when replacing bulb
WARNING : Do not attempt to replace LED lights due to high voltage exposure.
24
Care & Cleaning
Short
Vacations
Long
Vacations
Vacation and Moving Tips
• Leave refrigerator operating during vacations of 3 weeks or less.
• Use all perishable items from refrigerator compartment.
• Turn automatic ice maker off and empty ice bucket, even if you will only be gone for a few days.
• Remove all food and ice if you will be gone one month or more.
• Turn off automatic ice maker and turn water supply valve to closed position.
• Turning control knobs to “0” on the refrigerator (fresh food) control box only controls your refrigerator’s cooling system. To turn off power to your refrigerator you must unplug the power cord from the wall outlet.
• Clean interior thoroughly.
• Leave both doors open to prevent odors and mold build-up. Block doors open if necessary.
Moving • Remove all food and ice.
• If using handcart, load from side.
• Adjust rollers all the way up to protect them during sliding or moving.
• Pad cabinet exterior to avoid scratching surface.
25
Before You Call
TROUBLESHOOTING
GUIDE
PROBLEM
Before calling for service, review this list. It may save you time and expense. This list includes common occurrences that are not the result of defective workmanship or materials in this appliance.
CAUSE
AUTOMATIC ICE MAKER (some models)
CORRECTION
Ice maker is not making any ice.
• Ice maker wire signal arm is in the “up” or
OFF position.
• Household water line valve is not open.
• Freezer is not cold enough.
• Move wire signal arm to the
“down” or ON position (side mounted).
• Turn on household water line valve.
• See PROBLEM column
TEMPERATURES ARE TOO WARM.
• Saddle valve on cold water pipe is clogged or restricted by foreign material.
• Turn off household water line valve.
Remove valve. Ensure that valve is not a self-piercing saddle valve. Clean valve. Replace valve if necessary.
Ice maker is not making enough ice.
• Ice maker is producing less ice than you expect.
• Freezer is not cold enough.
• Household water line valve is not completely open.
• The ice maker will produce 2 to
3 pounds of ice every 24 hours depending on usage conditions.
Ice is produced at a rate of 8 cubes every 75 to 160 minutes.
• See PROBLEM column
TEMPERATURES ARE TOO WARM.
• Turn on household water line valve.
Ice maker will not stop making ice.
Ice cubes are freezing together.
Ice has bad odor and taste.
•
•
•
Ice maker wire signal arm is being held down by some item in the freezer.
Ice cubes are not being used frequently enough.
Freezer control is set too warm.
• Very little food in freezer.
• Ice has picked up odor or flavor from strong food stored in refrigerator or freezer.
• Move item and release wire signal arm. Remove any ice cubes that are frozen together over the wire signal arm.
• Remove ice container and discard ice from container. Ice maker will produce fresh supply.
• Set freezer control to colder setting. Allow 24 hours for temperature to stabilize.
• Add more food to freezer.
• Cover foods tightly. Discard stale ice. Ice maker will produce fresh supply. Replace air filter (available in select models).
• Water running to ice maker has poor taste or odor.
• Ice not used frequently enough.
• Add filter to water supply line. Consult a water purifying company.
• Discard stale ice.
LIGHT BULB IS NOT ON
Light bulb is not on.
•
•
Light bulb is burned out.
No electric current is reaching refrigerator.
• See Replacing Light Bulbs in
& CLEANING section.
CARE
• See PROBLEM column RUNNING
OF REFRIGERATOR.
26
Before You Call
PROBLEM CAUSE CORRECTION
ODORS IN REFRIGERATOR
Interior is dirty.
• Interior needs to be cleaned.
• Food with strong odors is in refrigerator.
• See table of Care and Cleaning
Tips in CARE & CLEANING section.
• Cover food tightly.
OPENING/CLOSING OF DOORS/DRAWERS
Door(s) will not close.
• Door was closed too hard, causing other door to open slightly.
• Refrigerator is not level. It rocks on the floor when moved slightly.
•
•
Close both doors gently.
Ensure floor is level and solid, and can adequately support the refrigerator. Contact a carpenter to correct a sagging or sloping floor.
Drawers are difficult to move.
•
•
Food is touching shelf on top of drawer.
Track that drawers slide on is dirty.
• Remove top layer of items in drawer.
• Ensure drawer is properly installed on track.
• Clean drawer, rollers, and track.
See table of Care and Cleaning
Tips in CARE & CLEANING section.
RUNNING OF REFRIGERATOR
Compressor and/or fan does not run.
Refrigerator runs too much or too long.
Compressor goes off and on frequently.
• Refrigerator is in
•
• defrost cycle.
Plug at electrical outlet is disconnected.
• House fuse blown or tripped circuit breaker.
Power outage.
• Refrigerator is going through a self diagnostic test.
• Room or outside weather is hot.
• Refrigerator has recently been disconnected for a period of time.
• Automatic ice maker is operating.
• Doors are opened too frequently or too long.
• Fresh Food/freezer door may be slightly open.
• Fresh Food/freezer gasket is dirty, worn, cracked, or poorly fitted.
• Thermostat keeps the refrigerator at a constant temperature.
• This is normal for a fully automatic defrost refrigerator. The defrost cycle occurs periodically, lasting about 30 minutes.
• Ensure plug is tightly pushed into outlet.
• Check/replace fuse with a 15 amp time-delay fuse. Reset circuit breaker.
• Check house lights. Call local electric company.
• Allow 15 minutes to complete self test.
• It is normal for the refrigerator to work longer under these conditions.
• It takes 8-12 hours for the refrigerator to cool down completely.
• Ice maker operation causes refrigerator to run slightly more.
• Warm air entering the refrigerator causes it to run more. Open doors less often.
• Ensure refrigerator is level. Keep food and containers from blocking door.
See PROBLEM column OPENING/
CLOSING OF DOORS/DRAWERS.
• Clean or change gasket. Leaks in door seal will cause refrigerator to run longer in order to maintain desired temperatures.
• This is normal. Refrigerator goes on and off to keep temperature constant.
27
Before You Call
PROBLEM CAUSE CORRECTION
TEMPERATURE TOO COLD IN REFRIGERATOR (FRESH FOOD) OR FREEZER
Freezer temperature too cold. Fresh
Food temperature is satisfactory.
Fresh Food temperature too cold. Freezer temperature is satisfactory.
Food stored in drawers freezes.
• Freezer control is set too cold.
•
•
Fresh Food control is set too cold.
Fresh Food control is set too cold.
•
•
•
Set freezer control to a warmer setting. Allow 24 hours for temperature to stabilize.
Set fresh food control to a warmer setting. Allow 24 hours for temperature to stabilize.
See solution above.
TEMPERATURE TOO WARM IN REFRIGERATOR (FRESH FOOD) OR FREEZER
Freezer/Fresh Food temperature is too warm.
•
•
Doors are opened too frequently or too long.
Door is slightly open.
Freezer temperature is too warm. Fresh
Food temperature is satisfactory.
Fresh Food temperature is too warm. Freezer temperature is satisfactory.
•
•
Freezer control is set too warm.
Fresh Food control is set too warm.
WATER/MOISTURE/FROST INSIDE REFRIGERATOR
• Warm air enters the refrigerator whenever the door is opened.
Open the door less often.
• See PROBLEM column OPENING/
CLOSING OF DOORS/
DRAWERS.
• Set freezer control to a colder setting. Allow 24 hours for temperature to stabilize.
• Set Fresh Food control to a colder setting. Allow 24 hours for temperature to stabilize.
Moisture collects on inside of refrigerator walls.
•
•
Weather is hot and humid.
Door is slightly open.
• The rate of frost buildup and internal sweating increases.
• See PROBLEM column OPENING/
CLOSING OF DOORS/DRAWERS.
• Open door less often.
Water collects on bottom side of drawer cover.
• Door is opened too often or too long.
•
•
Open containers.
Vegetables contain and give off moisture.
• Keep containers covered.
• It is not unusual to have moisture on the bottom side of the cover.
• Move humidity control (some models) to lower setting.
Water collects in bottom of drawer.
• Washed vegetables and fruit drain while in the drawer.
WATER/MOISTURE/FROST OUTSIDE REFRIGERATOR
• Dry items before putting them in the drawer. Water collecting in bottom of drawer is normal.
Moisture collects on outside of refrigerator or between doors.
•
•
Weather is humid.
meet warm air from outside.
Door is slightly open, causing cold air from inside refrigerator to
• This is normal in humid weather.
When humidity is lower, the moisture should disappear.
• See PROBLEM column OPENING/
CLOSING OF DOORS/
DRAWERS.
28

Public link updated
The public link to your chat has been updated.
Advertisement