User`s Manual - PLANET Technology Corporation.

User`s Manual - PLANET Technology Corporation.
User’s Manual
)XOO+'3R(%R[,3&DPHUD
*$"
www.PLANET.com.tw
User’s Manual of ICA-2200
Copyright
Copyright © 2012 by PLANET Technology Corp. All rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language or computer language, in any form or by any means, electronic, mechanical, magnetic,
optical, chemical, manual or otherwise, without the prior written permission of PLANET.
PLANET makes no rep resentations or warranties, either expressed or implied, with respect to
the contents hereof and specifically disclaims any warranties, merchantability or fitness for any
particular purpose. Any software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not PLANET, its distributor, or
its dealer) assumes the entire co st of all necessary servicing, repair, and any incident al or
consequential damages resulting from any defect in the software. Further, PLANET reserves the
right to revise this publi cation and to make changes from time to time in the content s hereof
without obligation to notify any person of such revision or changes.
All brand and product names mentioned in th is manual are trademarks and/or registered
trademarks of their respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rul es. These limits are designed to provide reasonable protection
against harmful interference in a re sidential installation. This eq uipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accorda nce with the
instructions, may cause harmful interference to ra dio communications. However, there is n o
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or tel evision reception, which can be determined by turning t he
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit dif ferent from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
To assure continued compliance. (Example-use only shielded interface cables when connecting
to computer or peripheral devices). Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the Followi ng two
conditions: ( 1 ) Thi s device may not cause harmful interference, and ( 2 ) this Devi ce must
accept any interference received, including interference that may cause undesired operation.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment.
In order to a void the possibility of exceeding the FCC radio frequency exposure limits, human
proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.
II
User’s Manual of ICA-2200
Safety
This equipment is designed with the utmost ca re for the safety of those who in stall and use it.
However, special attention must be paid to the dangers of elect ric shock and static electricity
when working with electrical equipment. All guidelines of this and of the computer manufacture
must therefore be allowed at all times to ensure the safe use of the equipment.
CE Mark Warning
This is a Class B product. In a dom estic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
WEEE Regulation
To avoid the potential effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment, end users
of electrical and electronic equipment should understand the meaning of the
crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal
waste and have to collect such WEEE separately.
Revision
User’s Manual for PLANET Full HD PoE Box IP Camera
Model: ICA-2200
Rev: 1.0 (July. 2012)
Part No. EM-ICA2200 Series_v1.0
III
User’s Manual of ICA-2200
CONTENTS
Chapter 1. Product Introduction ......................................................................................................... 1
1.1. Package Contents .................................................................................................................. 1
1.2. Product Description ................................................................................................................ 1
1.3. Product Features .................................................................................................................... 5
1.4. Product Specification .............................................................................................................. 6
Chapter 2. Hardware Interface............................................................................................................. 8
2.1. Front View............................................................................................................................... 8
2.2. Rear View ............................................................................................................................... 9
2.3. Hardware Installation.............................................................................................................11
Chapter 3. Initial Utility Installation................................................................................................... 12
3.1. Preparation ........................................................................................................................... 15
3.1.1. Search and View by PLANET IP Wizard II ............................................................... 15
3.2. Using UPnP of Windows XP or Vista or Win7 ...................................................................... 19
Chapter 4. Installation Guide ............................................................................................................. 20
4.1. System Requirements .......................................................................................................... 20
4.2. Before You Begin.................................................................................................................. 21
4.2.1. Connecting to Internet Camera ................................................................................ 21
Chapter 5. Web Configuration for Live View.................................................................................... 23
5.1. Live View .............................................................................................................................. 23
5.2. ActiveX Control ..................................................................................................................... 25
5.2.1. Digital Zoom.............................................................................................................. 25
5.2.2. Snapshot................................................................................................................... 26
5.2.3. Record ...................................................................................................................... 26
5.2.4. Volume ...................................................................................................................... 28
5.2.5. About......................................................................................................................... 28
Chapter 6. Configuration & Operation.............................................................................................. 29
6.1. Network Configuration .......................................................................................................... 29
6.1.1. Network..................................................................................................................... 29
6.1.2. IPv6 function ............................................................................................................. 31
6.1.3. HTTPS ...................................................................................................................... 31
6.1.4. DDNS server............................................................................................................. 32
6.1.5. PPPoE ...................................................................................................................... 33
6.1.6. Streaming.................................................................................................................. 34
6.1.7. UPnP......................................................................................................................... 36
6.1.8. Bonjour...................................................................................................................... 37
IV
User’s Manual of ICA-2200
6.1.9. ONVIF ....................................................................................................................... 37
6.1.10. IP Filter.................................................................................................................... 38
6.1.11. IP Notification .......................................................................................................... 39
6.2. Adjust Camera Configuration ............................................................................................... 41
6.2.1. Picture....................................................................................................................... 41
6.2.2. Privacy Mask ............................................................................................................ 44
6.2.3. PTZ Setting............................................................................................................... 45
6.2.4. Preset Setting ........................................................................................................... 46
6.2.5. Tour Setting............................................................................................................... 46
6.3. System.................................................................................................................................. 47
6.3.1. System ...................................................................................................................... 48
6.3.2. Date & Time .............................................................................................................. 48
6.3.3. Maintenance ............................................................................................................. 50
6.4. Video..................................................................................................................................... 52
6.4.1. Common ................................................................................................................... 52
6.4.2. Video Profile.............................................................................................................. 53
6.4.3. ROI............................................................................................................................ 55
6.5. Audio Configuration .............................................................................................................. 55
6.6. User Privilege Access Configuration .................................................................................... 56
6.7. E-Mail Configuration ............................................................................................................. 57
6.8. Object Detection ................................................................................................................... 58
6.9. Storage Configuration........................................................................................................... 59
6.9.1. SD Card .................................................................................................................... 59
6.9.2. SAMBA Server.......................................................................................................... 60
6.10. Continuous Recording ........................................................................................................ 61
6.11. Recording List..................................................................................................................... 61
6.11.1. Recording List ......................................................................................................... 61
6.11.2. Continuous Recording List...................................................................................... 62
6.12. Event Server Configuration ................................................................................................ 63
6.12.1. FTP Server.............................................................................................................. 63
6.12.2. TCP Server ............................................................................................................. 64
6.12.3. HTTP Server ........................................................................................................... 65
6.12.4. SAMBA Server........................................................................................................ 66
6.13. Event Schedule Configuration............................................................................................ 67
6.14. Record Configuration.......................................................................................................... 71
6.15. Port Status .......................................................................................................................... 72
Chapter 7. PLANET DDNS Application............................................................................................. 73
Chapter 8. Alarm I/O Connector ........................................................................................................ 74
Chapter 9. PING IP Address............................................................................................................... 76
V
User’s Manual of ICA-2200
Chapter 10. Bandwidth Estimation ................................................................................................... 77
Chapter 11. Configure Port Forwarding Manually........................................................................... 78
Chapter 12. Power Line Frequency................................................................................................... 81
Chapter 13. 3GPP ............................................................................................................................... 83
Chapter 14. Troubleshooting & Frequently Asked Questions ....................................................... 84
VI
User’s Manual of ICA-2200
Chapter 1. Product
Introduction
1.1. Package Contents
The following items should be contained in the package:
„ ICA-2200 / Full HD PoE Box IP Camera x 1
„ Power Adapter x 1
„ Camera Mount Kit x 1
„ User’s Manual CD x 1
„ Quick Installation Guide x 1
„ Screw Packet x 1
„ A/V cable x 1
NOTE:
1. If any of the above items are missing, please contact your dealer immediately.
2. Using the power supply that is not the one included in Internet Camera package
will cause damage and void the warranty for this product.
1.2. Product Description
Superb Full HD Quality for Professional Surveillance
The PLANET ICA-2200 (or “Internet Camera” in the following section) is a Full HD camera for a
wide range of video surve illance over I P networks. It suppo rts H.264, MPEG-4, and M-JP EG
compression formats to d eliver excellent picture quality in 1080 P resolutions at 30 frame s per
second (fps). Superb 1080P video quality is provided with progressive scan in multiple individual
streams, 16:9 aspect ratio and frame rate. The ICA-2200 offers high-performing video surveillance
in both indoor and outdoor applications. It is perfect for securing locations such as buildings, roads,
parking areas, garages, railway stations, airports and more.
1
User’s Manual of ICA-2200
Day & Night Surveillance
The ICA-2200 features an automatic, removable infrared-cut filter to p rovide color video when
there is sufficient light, and black/white video in dark conditions. The ICA-2200 is able to maintain
clear images 24 hours a day.
2
User’s Manual of ICA-2200
Extraordinary Image quality
Together with powerful image processing attr ibutes like Wid e Dynamic Range (WDR) and
3-Dimension Noise Reduction (3DNR) technology, the ICA-22 00 is able to filter the intense
backlight surrounding a subject and remove noises from video signal. Thus, an extremely clear
and exquisite picture quality can be produced even under any challenging lighting conditions.
3
User’s Manual of ICA-2200
Advanced event management
The ICA-2200 supports a number of advanced features that enhance the camera flexibility and
capabilities. The Auto-Iris function improves the image quality and avoid over exposure. The AV
output enables 2-Way audio communication. The embedded micro SD/SDHC card slot
facilitates the image storage locally. It also provides the RS-485 interface for an optional pan/tilt
enclosure connection to effectively perform pan/tilt management. The inputs/outputs interface
in the ICA-2200 can connect to external devices such as door sensors and relays to activate
light or close doors automatically.
Flexible installation and Power functionality
The ICA-2200 incorporates 802.3af Power over Et hernet standard so it can b e powered via the
network cable, eliminating the need for powe r cables and redu cing installation costs. The
ICA-2200 is ONVIF com pliant and therefore is inte roperable with other bran ds in the marke t. It
also includes the 64 chan nel central management software for efficient surveillance monitoring.
The ICA-2200 is indisputably the top choice for reliable and high performance surveillance.
4
User’s Manual of ICA-2200
1.3. Product Features
¾
Camera
„
1 / 2.7” Progressive 2MP CMOS sensor
„
3.3~12 mm Vari-focal, Auto-iris Lens
„
0.5 lux Minimum Illumination at F1.4
„
Maximum resolution 1920 x 1080
„
Removable IR-cut Filter for Day & Night Function
„
CS- or C-mount Adjustment Ring for Flexible Lens Installation
¾
Video / Audio
„
H.264 / MPEG-4 and M-JPEG video compression simultaneously
„
Simultaneous multi-stream support
„
H.264 high profile, main profile and baseline
„
Max. Resolution 1080P at 30fps
„
3DNR to improve picture quality at low Lux
„
WDR Enhancement for enhance visibility under extremely bright or dark environments
„
Two-way audio support with enhanced audio quality
¾
Network and Configuration
„
Compliant with IEEE 802.3af PoE interface for flexible deployment
„
Auto MDI/MDI-X supported
„
Support for IPv6 in addition to the standard IP protocol version 4
„
RTSP / UPnP / 3GPP / HTTPS protocols selectable
¾
Easy Installation & Management
„
ONVIF compliant for interoperability
„
Built-in Samba client for NAS
„
3GPP for 3G mobile remote applications
„
RS485 interface for P/T scanner control
„ Digital Input/Outputs for integration with sensors and alarm
„ Cam Viewer 3 Central management software supported
5
User’s Manual of ICA-2200
1.4. Product Specification
Model
ICA-2200
Camera
Image device
1/2.7" progressive scan CMOS sensor
Lens
Vari-Focal 3.3~12mm, F1.4 DC Auto-Iris, CS mount
Mechanical IR Cut Filter
Angle of view (horizontal Field): 79.3°x 29.8°
Minimal Illumination
0.5 lux @ F1.4
Effective Pixels
1920 x 1080 pixels
Image
Video Compression
H.264 / MPEG-4 / M-JPEG
Video Resolution
1080P mode
H.264: 1080P / 640 x 360 / 320 x 180 / 160 x 90
M-JPEG: 1080P / 640 x 360 / 320 x 180 / 160 x 90
MPEG4: 640 x 360 / 320 x 180 / 160 x 90
720P mode
H.264: 1280 x 720 / 640 x 360 / 160 x 90
M-JPEG: 1280 x 720 / 640 x 360 / 160 x 90
MPEG-4: 640 x 360 / 160 x 90
Frame Rate
Up to 30fps for all resolutions
Image Setting
AE, AWB
3D Noise reduction
WDR
Color, brightness, sharpness, contrast
Mirror / Flip
8 Privacy Masks
Text, time and date overlay
Streaming
Simultaneously multi-profile streaming
Streaming over UDP, TCP, or HTTP
M-JPEG streaming over HTTP (server push)
Supports 3GPP mobile surveillance (MPEG4)
Controllable frame rate and bandwidth
Constant and variable bit rate (MPEG4 / H.264)
ROI
Audio
Audio Streaming
2-Way Audio
Audio Compression
RTSP: G.711 64kbps, G.726 32kbps
3GPP: AMR
Microphone
External microphone input
Audio Output
Adjustable audio output gain
Network and Configuration
Standard
IEEE 802.3 10Base-T
6
User’s Manual of ICA-2200
IEEE 802.3u 100Base-TX
Protocol
IPv4, IPv6, TCP/IP, UDP, HTTP, HTTPS, SMTP, FTP, NTP, DNS,
DDNS, DHCP, ARP, Bonjour, UPnP, RTSP, RTP, RTCP, IGMP,
PPPoE, 3GPP, ICMP, Samba
Security
Password protection, IP address filtering, HTTPS encrypted data
transmission, user access log
Users
20 clients on-line monitoring at the same time
System Integration
Application Programming Interface
Open API for software integration
ONVIF Compliant
Alarm Triggers
Intelligent video motion detection and external input
Alarm Events
File upload via FTP, Samba to NAS, SD card or email
Notification via email, HTTP, and TCP
External output activation
Audio alerting output
Pre and post-alarm buffering
General
Power Requirement
12V DC, 1A
IEEE 802.3af Class 3
Power Consumption
6W max.
Operating Temperature
0 ~ 50 Degree C
Operating Humidity
20 ~ 80% (non-condensing)
Weight (include LENS)
392g
Dimension (W x D x H)
58 x 125 x 62 mm
Emission
CE, FCC
Connectors
10/100Mbps Ethernet, RJ-45
DC power jack
Terminal block for 1 alarm input and 1 output
RS-485 interface for pan/tilt scanners control
External MIC input
Audio output
Composite video output
Micro SD/SDHC card (Max 32GB, Class 6)
Factory default reset
7
User’s Manual of ICA-2200
Chapter 2. Hardware Interface
2.1. Front View
1
Lens
User could adjust the focus to get the best picture quality.
2
Internal
Microphone
The Camera has built-in an in
ternal microphone. This
microphone is hidden in the pinhole located on the front panel.
3
Back Focus Ring
Adjust this ring to adapt focus of C/CS mount lens
8
User’s Manual of ICA-2200
2.2. Rear View
1.
MIC In
Connect an external microphone to the network camera.
2.
Audio
Output
Connect a loud spe aker to the network cam era. This function is for alerting
sound and two-way audio.
The input power is 12VDC.
3.
DC Power
4
Micro SD
Card Slot
5
LAN
Socket
Note that supply the power to the Camera with the powe r adapter included in
package. Otherwise, the improper power adapter may damage the unit and
result in danger.
User can insert a micro SD card into this slot for event recording.
The LAN socket is a RJ-45 connector for connections to 10Base-T Ethernet or
100Base-TX Fast Ethernet
cabling. This Ethernet port supports
Auto-Negotiation can detect or negotiate the transmission speed of the network
automatically. Please use Category 5 cable to connect the Network Camera to a
100Mbps Fast Ethernet network switch or hub.
The LAN port also supports IEEE802.3af class 3 Power over Ethernet capability
that can direct connect wi th standard IEEE802.3af mid-span / end-sp an PSE
(Power Sourcing Equipment) device. No DC power required if the ICA-2200 is
connected with 802.3af PSE.
9
User’s Manual of ICA-2200
In the LAN socket, there are two LEDs embedded:
Power LED (orange color)
This LED is used to indicate whether DC power is on or not.
LAN LED (green color)
This LED will be flashing while network accessing via Ethernet.
Sometimes restarting the device will m ake the system back to a normal state.
However, if the system still got problems af ter restart, user can restore the
factory default settings and install it again.
6
Factory
Default
Reset
7
DI/DO
Connector
8
Video Out
9
DC Iris
Restore the device:
1.
Make sure the Camera is ready first. Insert the p aper clip o r other
suitable tool to press and hold the button down continuously.
2.
Hold it lea st 5 se conds and release the tool. Then the device h as
been restored to default settings and reboot again.
Note: Restoring the factory default set ting will lose the all previous settings
included IP address forever. User needs to run the IPWiza rd II program to
search the device and configure it to let the device work properly again.
The Internet Camera provides a terminal block with 6 pins of connectors for DI,
DO, and RS485. Please refer to the Appendix A in this manu al for more
information.
Cable for I/O connectors:
Name
Number
Function
12VDC
1
DC 12V (50mA maximum)
DI
2
Digital signal input
GND
3
GND
DO
4
Digital signal output
485+
5
RS485 data +
4856
RS485 data The Internet Camera also provides composite video output. Th e video o utput
function is only for easy installation to check view angle and focus. The output is
not a Mega-pixel resolution. Furthermore, the video output is off by default. To
turn on video, please refer to Setting\Camera\Picture chapter.
The Internet Camera supports DC-Iris control.
10
User’s Manual of ICA-2200
2.3. Hardware Installation
1. Fix the included stand to desired location
2. Attach the Camera to the stand
3. Plug an Ethernet cable into the Camera
Connect an Ethernet cable to the LAN socket located on the camera ’s rear and attach it
to the network.
4. Connect the external power supply to Camera
Connect the included power adapter to the DC power jack of the camera.
NOTE:
Use the power adapter, 12VDC, included in the package and connect it to wall outlet
for AC power. If the ICA-2200 is connected with IEEE802.3af Power over Ethernet
device such as PoE injector or PoE Switch, DC power is not required. Either power
the ICA-2200 from local DC power or PoE unless for purpose.
5. Done
Once you have installed the camera well and powered it on, the Power LED (orange) will
turn on late r. Once the Power LED turned o n, it means the syste m is bootin g up
successfully. Furthermore, if you ha ve a proper network co nnection, and access to the
camera, the LAN LED will flash green.
11
User’s Manual of ICA-2200
Chapter 3. Initial Utility Installation
This chapter shows how to quick set up your Inte rnet camera. The Internet camera is with the
default settings for the first time power on.
Default IP: DHCP Client OR 192.168.0.20 (if NO DHCP server existed in the network)
Username: admin
Password: admin
However, if you are not fa miliar with network setting and to help you find the networke d Internet
camera quickly, the windows utility PLANET IP Wizard II can search the cam eras in the network
that shall help you to configure some basic setting before you started advanced management and
monitoring.
1. Insert the bundle d CD into the CD-ROM driv e to launch the
completed, a welcome menu screen will appear.
auto-run p rogram. Once
2. Click the “IP Wizard II” hyperlink; you will see the dialog box as below.
NOTE:
If the welcome screen does not appear, click “Start” at the taskbar. Then, select “Run”
and type “D:\Utility\IPWizard II\setup.exe”, assume D is your CD-ROM drive.
3. The “Welcome to the InstallShield Wizard for PLANET IP Wizard II” prompt will display on the
screen and click “Next” to continue.
12
User’s Manual of ICA-2200
4. Please click “Next” to inst all with origin al settings, o r you may click “ Change…” button to
modify the install folder then press “Next” to continue.
13
User’s Manual of ICA-2200
5. Please click “Install” to start the installation.
6. Please click “Finish” to complete the installation and launch program immediately.
14
User’s Manual of ICA-2200
3.1. Preparation
When you in stalled the In ternet Camera on a LAN environment, you may execute PLA NET IP
Wizard II to discover camera’s IP address and set up related parameters in the camera.
3.1.1. Search and View by PLANET IP Wizard II
When you installed the Internet Camera on a LAN environment, you have two easy ways to search
your cameras by PLANET IP Wizard II or UPnP discovery. Here is the way to execute PLANET IP
Wizard II to discover camera’s IP address and set up related parameter in a camera.
9
Search
15
User’s Manual of ICA-2200
When launch the Planet IP Wizard II, a searching windows will pop up. Planet IP Wizard II is
starting to search Internet Cameras on the LAN. The existed devices will be listed as below.
16
User’s Manual of ICA-2200
9
View
If Planet IP Wizard II finds Internet Camera, View button will be available. Please select the
camera you want to view, key in the user name, password, i.e. “admin” by default and click the
View button. Then you could see the Video from camera directly. Furthermore you could double
click the left button of mouse to link to the Internet Camera by browser.
In case you want to change the IP related parameters of wired interface, please select the Internet
Camera you want to configure and click the LAN button. Relative settings will be carried out as
below.
17
User’s Manual of ICA-2200
In case, you do not want to change username and/or password, then just click “Submit” button to
perform your setting accordingly. Click “<<” button will go back to previous page.
If you like to change username and/or password of the device, just click the check button. Then,
the related fields will show up as below.
After keying in new username and p assword, click “Submit” button to perform your se tting
accordingly. Click “<<” button will go back to previous page.
18
User’s Manual of ICA-2200
3.2. Using UPnP of Windows XP or Vista or Win7
UPnP™ is short for Universal Plug a nd Play, whi ch is a n etworking architecture that p rovides
compatibility among network ing equipment, software, and perip herals. This device is an UPnP
enabled device. If the operating system, Windows XP, of your PC is UPnP enabled, the device will
be very easy to configure. Use the following step s to enable UPnP settings only if your operating
system of PC is running Windows XP.
NOTE:
Please notice that MS Windows 2000 does not support UPnP feature.
To discover your device, go to your Computer and click Network.
Click the targeted Device. Then Internet Explorer will connect to this IP Camera automatically.
19
User’s Manual of ICA-2200
Chapter 4. Installation Guide
4.1. System Requirements
The Internet Camera can be monitoring on all of Windows operating system that sugg est with
system requirment below in order to got better video performance.
Network Interface
10/100Base-TX Ethernet
Monitoring System
Recommended for Internet Explorer 8.0 or later
System Hardware
· CPU: Intel® Core™ i3 Processor or faster
· Memory Size : 2GB or more
· VGA card resolution : 1920 x 1080 or higher
· VGA card memory : 1GB or above
NOTE:
1. The listed information is minimum system requirements only. Actual requirement
will vary depending on the nature of your environment.
2. The ICA-2200 series can be managed by PLANET IP Wizard II if you want to
configure more detail information and settings of PLANET IP Wizard II software
please refer to the CD-ROM folder “D:\Utility\IPWizardII\setup.exe”, assume D is
your CD-ROM drive.
20
User’s Manual of ICA-2200
4.2. Before You Begin
The Internet Camera can be configured with your Web Browser. Before configure, please make
sure your PC is under the same IP segment with Internet Camera.
4.2.1. Connecting to Internet Camera
z
Use the following procedure to establish a connection from your PC to the Internet Camera.
z
Once connected, you can add the camera to your Browser’s Favorites or Bookmarks.
Start the web browser on the computer and type the IP address of the camera.
The Default IP: “http://192.168.0.20“
NOTE:
If your network is with DHCP server, by default, your DHCP server will provide an
IP address for ICA-2200. Please check the DHCP server’s status page for the real
IP address of the ICA-2200. Or through the IP Wizard II to get the IP information.
The ICA-2200 will use IP address 192.168.0.20 only if there is no DHCP server
existed in the connected network.
The login window of Internet Camera will appear,
Default login username/password is: admin / admin
NOTE:
If the User name and Password have been changed with PLANET IP Wizard II,
please enter the new User name and Password here.
21
User’s Manual of ICA-2200
After logged on, you should see the following messages at the top of Internet Explorer:
Click on the message, and click Run Add-on
When you see this message, click Run’ to install required ActiveX control
After the ActiveX control was installed and run, the first image will be displayed.
You should be able to see the images captured from the Internet Camera in the web page now. For
advanced functions, please refer to instructions given in follows chapters.
NOTE:
If you log in the camera as an ordinary user, setting function will be not available. If
you log in the camera as the administrator, you can perform all the settings
provided within the device.
22
User’s Manual of ICA-2200
Chapter 5. Web Configuration
for Live View
5.1. Live View
Start-up screen will be as follow no matter an ordinary users or an administrator.
Video Profile
Streaming Protocol
Language
ActiveX Control
Monitor Image Section
Setting Menu
Client Menu
Video Information
2-Way Audio
Monitor
Section
Image
Full Screen
The image shot by the camera is shown here. The date and time are
displayed at the top of the window.
Video Profile
The camera support multi-profile for three compressions H264,
MEPG-4 and M-JPEG si multaneously. User can ch ose the prop er
and/or preferred profile here.
Full Screen
Click this button to display the image in full-screen mode (uses every
available space to display the image captured by this camera).
2-Way Audio
The Internet Camera supports 2-way audio function. User can chose
to enable or disable this function by toggling the icon below
23
User’s Manual of ICA-2200
: Disable audio uploading function.
: Enable audio uploading function.
ActiveX Control
The plug-in ActiveX control supports a lot of functions by clicking the
left mouse button. Note that this feature only supports on the ActiveX
control within Microsoft® Internet Explorer.
Setting Menu
This function is d etail setting for th e camera that only available fo r
user logged into camera as administrator.
Item
Action
Network
Configure Network settings such as IPv6, ONVIF,
DHCP, DDNS, 3GPP, PPPoE and UPnP.
Camera
Adjust camera parameters.
System
Configure system information, date & time,
maintenance, and view system log file.
Video
Configure bit rate and
profiles.
Audio
Configure audio parameters.
User
Setup user name, password and login privilege.
E-Mail
Object Detection
Storage
Continuous
Recording
Recording List
frame rate of video
Setup E-Mail configuration.
Setup Object detection.
Status and configuration of SD card a nd Samba
server.
Files list inside the SD Card and Samba server.
Files list inside the SD Card.
Event Server
Setup FTP/TCP/HTTP/Samba server for event
Event Schedule
Configure the schedule while event triggered.
Streaming Protocol
User can select proper streaming protocol according to networking
environment.
Language
The device could provide multiple lan guages to m eet customer’s
requirement.
24
User’s Manual of ICA-2200
Client Setting:
Click this button to displ ay the client e xtra control panel for 2-way
Audio and Full Screen.
Video Information
Display video information inclu ding video format, resolution, fram e
rate and bit rate.
5.2. ActiveX Control
The plug-in ActiveX control supports a lot of functions by clicking the left mouse button. Note that
this feature only supports on the ActiveX control within Microsoft® Internet Explorer.
On the ActiveX control icon, click the Left Mouse Button, then a menu pop-up. This menu provides
features that are unique to the ActiveX control. These features include:
• Digital Zoom,
• Snapshot,
• Record,
• Volume,
• About
5.2.1. Digital Zoom
Click Digital Zoom to active this function as above. User can drag or scale the box over the video
to adjust zoom ratio and position.
25
User’s Manual of ICA-2200
5.2.2. Snapshot
Click Snapshot to activate this function. Press Snapshot button to take a picture. The image file is
saved as JPEG format into your local PC. Select Browser, the pop-up window to select the save
path and file name prefix, select OK to continue.
If you like to retrieve the saved image, select the file to display the saved image by using any one
of graph editing tools.
5.2.3. Record
Click Record to ac tivate this function. Press Record button to st art recording. The video file is
saved as ASF format into your local PC. While you want to stop it, press Stop to stop recording.
Select Browser, the po p-up window to select the save path and file name p refix, select OK to
continue.
After stop recording, list the files, this file is named as Video_yyyymmddhhmmss.asf
The ASF files can be display by the standard Windows Media Player, but it needs the DixectX 9.0
26
User’s Manual of ICA-2200
or later version to be installed.
27
User’s Manual of ICA-2200
5.2.4. Volume
Click Volume to activate this function. These have two co ntrol bars for speaker and microphone
volume. Scroll this control bar to adjust the audio attribute. Check the volume mute will mute the
speaker output.
5.2.5. About
Click About to show the ActiveX information
28
User’s Manual of ICA-2200
Chapter 6. Configuration &
Operation
6.1. Network Configuration
6.1.1. Network
This section provides the menu of connecting the device through Ethernet cable.
MAC address
Display the Ethernet MAC address of the device. Note that user cannot
change it.
Obtain an IP address
automatically (DHCP)
Enable this checked box when a DHCP server is inst alled on the
network to i ssue IP address assignment. With t his setting, the IP
address is assigned automatically. If this d evice cannot get an IP
address within limited tries, the device will assign a default IP address
for 192.168.0.20.
If you do not select “O btain an IP address autom atically”, then you
need to enter these network parameters by yourself.
29
User’s Manual of ICA-2200
IP Address
This address is a unique n umbers that identifies a co mputer or device
on the WAN or LAN. T hese numbers are u sually shown in groups
separated by periods, for example: 192.168.0.200
Subnet Mask
Subnets allow network traffic between hosts to be separated based on
the network's configuration. In IP networking, traffic takes the form of
packets. IP subnets advance network se curity and perf ormance to
some level by organizing hosts into logical g roups. Subnet masks
contain four bytes and usually appear in the sa me "dotted decimal"
data. For e xample, a very comm on subnet ma sk in it s binary
demonstration 11111111 11111111 11111111 00000000 will usually be
shown in the corresponding, more readable form as 255.255.255.0.
Gateway
A gateway is a piece of so ftware or hardware that passes information
between networks. You'll see this term most often when you either log
in to an Inte rnet site or when you're transient email between different
servers.
Obtain
DHCP
DNS
from
Enable this checked box when a DHCP
network and provide DNS service.
server is inst alled on the
Primary DNS
When you send email or position a browser to an Internet domain such
as xxxxx.com, the domain name system translates the names into IP
addresses. The term refers to two things: the conventions for naming
hosts and the way the names are control across the Internet.
Secondary DNS
The same function as DNS1. It is option not necessary
HTTP Port
The device supports two HTTP port s. The first one is default port 80
and this po rt is fixed. This port is very useful for Intranet usage. The
second HTTP port is cha ngeable. Users could assign the second port
number of ht tp protocol, and the WAN users should follow th e port
number to lo gin. If the http port i s not assigned as 80, users ha ve to
add the po rt number i n back of
IP addre ss. For example:
http://192.168.0.20:8080.
Therefore, the user can access the device by either
http://xx.xx.xx.xx/, or
http://xx.xx.xx.xx:xxxx/ to access the device.
If multiple de vices are installed on the LAN an d also required to be
accessed from the WAN, then the HTTP Port can be assigned as the
30
User’s Manual of ICA-2200
virtual server port mapping to support multiple devices.
NOTE
When the configuration is finish, please click “OK” to save and enable
the setting.
6.1.2. IPv6 function
Internet Protocol version 6 (IPv6) is called the “IP Next Generation” (IPng), which is designed to fix
the shortcomings of IPv4, su ch as data security and maximum n umber of use r addresses. It is
backward compatible and thus expected to slowly replace IPv4, with the two existing si de by side
for many years.
IPv6
To enable or disable the IPv6 function here.
6.1.3. HTTPS
HTTPS: Stands for Hypertext Transfer Protocol Secure
HTTPS is a combination of the Hypertext Transfer Protocol with the SSL/TLS protocol to provide
encrypted communication and secure identification of a network web server. HTTPS connections
are often used for sensitive transactions in corporate information systems. The main i dea of
HTTPS is to create a secure channel over an insecu re network. This en sures reasonable
protection from eavesdroppers and man-in-the-middle attacks, provided that adeq uate cipher
suites are used and that the server certificate is verified and trusted.
31
User’s Manual of ICA-2200
HTTPS
To enable or disable the HTTPS service here. Note that the HTTPS
function of this device is n ot only encrypted the web content but also
audio/video data.
Port
Choose the HTTPS port. The default value is 443.
6.1.4. DDNS server
Stands for Dynamic Domain Name Server
The device supports DDNS If your device is co nnected to xDSL directly, you might need this
feature. However, if your device is behind a NAT router, you will not need to enable this fea ture.
Because DDNS allows the device to use an easier way to remember naming format rather than an
IP address. The name of the domain i s like the name of a person, and the IP addre ss is like his
phone number. On the Internet we h ave IP numbers for each host (computer, server, router, and
so on), and we replace these IP numbers to easy remember names, which are organized into the
domain name. As to xDSL environment, most of the users will use dynamic IP addresses. If users
want to set up a web or a FTP serve r, then the Dynamic Domain Name Server is necessary. For
more DDNS configuration, please consult your dealer.
Your Internet Service Pro vider (ISP) p rovides you at least one IP address which you u se to
connect to the Internet. The address you get may be static, meaning it never changes, or dynamic,
meaning it’s likely to chan ge periodically. Just how often it changes, dep ends on your ISP. A
dynamic IP address complicates remote access since you may not know what your current WAN
IP address is when you want to access your network over the Internet. The solution to the dynamic
IP address problem comes in the form of a dynamic DNS service.
The Internet uses DNS servers to lookup domain names and translates them into IP addre sses.
Domain names are just e asy to remember aliases for IP addresses. A dynamic DNS se rvice is
unique because it provides a means of updating your IP address so that your l isting will remain
current when your IP address ch anges. There are several excellent DDNS services availa ble on
the Internet and best of all they’re free to use. One such service you can use is www.DynDNS.org.
You’ll need to register with the service and set up the domain name of your choice to begin using it.
Please refer to the hom e page of the service for detailed instructions or refer to Appendix E for
32
User’s Manual of ICA-2200
more information.
DDNS
To enable or disable the DDNS service here.
Server name
Choose the built-in DDNS server.
DDNS Host
The domain name is applied of this device.
User Name
The user name is used to log into DDNS.
Password
The password is used to log into DDNS.
6.1.5. PPPoE
PPPoE: Stands for Point to Point Protocol over Ethernet
A standard builds on Eth ernet and Point-to-Point network protocol. It allows Internet Ca mera
connect to Internet with xDSL or cable conne ction; it can dial up your ISP and get a dynamic IP
address. For more PPPoE and Internet configuration, please consult your ISP.
It can directly connect to the xDSL, however, it should be setup on a LAN environment to program
the PPPoE information first, and then connect to the xDSL modem. Power on again, then the
device will dial on to the ISP connect to the WAN through the xDSL modem.
The procedures are
• Connect to a LAN by DHCP or Fixed IP
• Access the device, enter Setting Î Network Î PPPoE as below
33
User’s Manual of ICA-2200
PPPoE
To enable or disable the PPPoE service here.
User Name
Type the user name for the PPPoE service which is provided by ISP.
Password
Type the password for the PPPoE service which is provided by ISP.
IP Address / Subnet
Mask / Gateway
Shows the IP information got from PPPoE server site.
Status
Shows the Status of PPPoE connection.
6.1.6. Streaming
RTSP is a streaming control protocol, and a starting point for negotiating transports such as RTP,
multicast and Unicast, and for negotiating codecs. RTSP can be considered a "remote control" for
controlling the media stream delivered by a media server. RTSP servers typically use RTP as the
protocol for the actual transport of audio/video data.
34
User’s Manual of ICA-2200
RTSP Port
Choose the RTSP port. The RTSP pro tocol allows a connecting client to
start a video stream. Enter the RTSP port number to use. The default value
is 554.
RTP Port
Specify the range of transmission port number of video stream. The default
range is 50000 to 50999. User can specify a number between 1024 and
65535.
NOTE
To use the 3GPP function, in addition to previous section, you might need
more information or configuration to make this function work.
The camera must be set as Multi-pro file mode, not Mega-pixe l mode.
Otherwise this device cannot serve 3GPP stream.
To use the 3GPP function, it strongly recommends installing the Networked
Device with a public and fixed IP address without any firewall protection.
Port 554 is the default for RTSP serv ice. However, sometimes, some
service providers change this port number for some reasons. If so, use r
needs to change this port accordingly.
Dialing
procedure
1.Choose a verified player (Packe
currently)
tVideo, Quicktime or Realplaye
r
2. Use the following URL to access: rtsp://host/mpeg4/media.3gp
Where host is the host name or IP address of the camera.
Compatible
3G mobile
phone
Please contact your deal er to get the approve d list of compat ible 3G
phone.
35
User’s Manual of ICA-2200
6.1.7. UPnP
UPnP is short for Universal Plug and Play, which is a networking a rchitecture that p rovides
compatibility among network ing equipment, software, and perip herals. This device is an UPnP
enabled Internet Camera. If your operating system is UPnP enabled, the device will automatically
be detected and a new icon will be ad ded to “My Netw ork Places.” If you do not want to use the
UPnP functionality, it can be disabled
In addition, this device also provide s UPnP IGD function for NAT traversal easily. Use NAT
traversal when your device is located on an intranet (LAN) and you wish to make it available from
the other (WAN) side of a NAT router. With NAT traversal properly configured, all HTTP traffic to
an external HTTP port in the NAT router will be forwarded to the device.
UPnP
To enable or disable the UPnP service here.
Friendly Name
Shows the friendly name of this device here.
UPnP NAT Traversal
When enabled, the device will attempt to configure port mapping in
a NAT router on your network, us ing UPnP™. Note that UPnP™
must be enabled in the NAT router first.
Port Range
The port range will open in NAT router.
External IP address
Show the IP address and port for WAN access through Internet. If
NAT traversal is config ured successfully, user ca n use this I P
address and port to access this device.
36
User’s Manual of ICA-2200
6.1.8. Bonjour
The Bonjour service allows IP camera can be discovered with Apple Safari browser applied, once
the option enable the IP camera will be show the Friendly Name in the Bonjour bookmarks menu
of Safari browser.
Bonjour
To enable or disable the Bonjour service here.
Friendly Name
Shows the friendly name of this device here.
6.1.9. ONVIF
ONVIF is a global and open industry forum with the goal to facilitate the development and use of a
global open standard for the interface of physical IP-based security products. Or in other words, to
create a standard for how IP products within video surveillance and other physical security areas
can communicate with each other.
ONVIF
To enable or disable the ONVIF interface here.
Version
Currently, the V1.0 or V1.01/1.02/V2.0/V2.1.1 is available.
37
User’s Manual of ICA-2200
6.1.10. IP Filter
You can enter different user’s IP address which are allowing enter or denying by the device.
IP Filter
To enable or disable the IP filter function here.
IP Filter Policy
Choose the filter policy where is denying or allowing.
38
User’s Manual of ICA-2200
6.1.11. IP Notification
In case the IP address is changed, system is abl e to send out an email to al ert someone if the
function is enabled.
SMTP Notification (e-mail)
If enable this function, then the “Send to“ and “Subject” field
need to be filled.
Send To
Type the receiver’s e-mail address. This address is used for
reply mail.
Subject
Type the subject/title of the E-mail.
TCP Notification
If enable this function, then the “ TCP Server“, “TCP Port”,
and “Message” fields need to be filled.
TCP Server
Type the server name or the IP address of the TCP server.
TCP Port
Set port number of TCP server.
Message
The message will be sent to FTP server.
HTTP Notification
If enable this function, then the fields below need to be filled.
URL
Type the server name or the IP address of the HTTP server
HTTP Login name
Type the user name for the HTTP server.
39
User’s Manual of ICA-2200
HTTP Login Password
Type the password for the HTTP server.
Proxy Address
Type the server name or the IP address of the HTTP Proxy.
Proxy Port
Set port number of Proxy.
Proxy Login name
Type the user name for the HTTP Proxy.
Proxy Login Password
Type the password for the HTTP Proxy.
Custom parameter
User can set specific parameters to HTTP server.
Message
The message will be sent to HTTP server.
40
User’s Manual of ICA-2200
6.2. Adjust Camera Configuration
Use this menu to set the function of the camera of Internet Camera
6.2.1. Picture
Rotation
Turn the “Mirror” and “Vertical Flip” On or OFF. The
image will be overturned as below.
41
User’s Manual of ICA-2200
White Balance
Iris/Exposure
Control
Auto: will adjust the white balance automatically.
Hold: will hold the white balance.
This Camera is built-in a DC-Iris lens. User can choose the
Iris control mode from “Auto” or “Off”. In case, the “Auto”
mode is selected, th e Camera will control DC Iris
automatically. On the h and, if the “Off” mode is selected,
the Camera will open the lens Iris to maximize.
Sometimes, the Auto Iris may work abnormally under some
environments. In this case, user can click “Calibrate” button
to adjust Auto Iris function again.
Maximum Exposure User can limit the ma ximum exposure time of the image
Time
sensor. The larger value means longer exposure time
possibly.
Power Frequency
Frequency of power line: 50 or 60Hz.
Color Level
Large value will be colorful.
Hue
Change the value will result to color tuning.
Brightness
Large value will brighten camera.
Contrast
Large value will contrast camera heavily.
Sharpness
Large value will sharpen camera.
3D De-Noise
3D De-Noise can remove or lower unwanted noise and
preserve fine details and edges.
ICR
Use built-in photo sensor or manual to control ICR.
In case use r selects manual mode, there are 4 modes:
Night (On), Day (Off), Auto or Schedule to control built-in IR
LEDs. This function is very useful under low illumination
environment even 0 Lux.
In case the Auto mode is selected, user needs to specify 3
parameters in advance:
Night Mode Threshold (0~10000): this valu e set the
threshold to turn on IR LED. It should be lower or equal t o
Day Mode Threshold.
Day Mode Threshold (0~10000): this value set the
threshold to turn off IR LED. It should be higher or equal to
42
User’s Manual of ICA-2200
Night Mode Threshold.
Delay Time: The delay time
switching.
between LED ON/OFF
Note: that Curre nt Value is the current lumina nce from the
captured video. It’s a u seful reference to set LED ON/OF F
Threshold.
Noise Reduction
This function is to reduce noise of input image.
WDR
This function is to provi de clear images even under back
light circumstances. The higher “Strength” level will adjust
contrast compensation stronger.
Default Settings
Restore to factory image settings.
43
User’s Manual of ICA-2200
6.2.2. Privacy Mask
Use this page to specify privacy mask window 1 to window 8 and set the name and gray level for
selected window.
Add and Delete
To add or delete the privacy mask windows, user can specify up to 7
windows to mask the video ca ptured by this device. By dragging
mouse on th e image, you can change the positio n and size of the
selected window accordingly.
Name
Name of the specified privacy window
Level
To define the gray level
darker.
44
of mask block. The smaller value will be
User’s Manual of ICA-2200
6.2.3. PTZ Setting
This page allow user to modify the RS-485 interface according to the P/T scanner.
Camera Protocol
This device can connect to a PTZ camera or speed dome camera and
controls them thru RS-485 interface.
This is the camera ID set in PTZ camera or speed dome camera.
Camera Address
Note that please DO NOT changes the default value if unnecessary.
If so, user needs to check and set value properly for both sides.
Baud rate
This is the communication speed between network module and P/T
scanner.
NOTE
If need to ch ange these parameters, user n eeds to check and set
value properly for both, network module and P/T scanner.
45
User’s Manual of ICA-2200
6.2.4. Preset Setting
This page provides the edit tool to modify or delete the “Preset Setting” item by item.
6.2.5. Tour Setting
Up to 64 p ositions can be preset, and the camera can be p rogramming to mo ve to the pre set
position sequentially.
46
User’s Manual of ICA-2200
Tour Name
The group name of the se quence of camera tour. The maximum number of
camera tour is 16.
Running
Enable or disable this camera tour.
Preset
Set the se quence of the t our. Maximum 16 p oints can be assigned. The
selected preset position is added in the Sequence list from 1 to 16.
Wait Time
Type a period of time during which the camera is to stay at each preset point,
between 0 to 36000 seconds.
NOTE
To use the camera tour functio n, user must preset some came ra positions
first. The maximum number of preset points is 64.
6.3. System
Use this menu to perform the principal settings of Internet Camera.
47
User’s Manual of ICA-2200
6.3.1. System
Device title
You can enter the name of this unit here. It’s very useful to identify the
specific device from multiple units.
Software version
This information shows the software version in the device.
Network LED
Switch the LED light of th is Internet Camera on or off, that Network
LEDs will stop working; in case you don’t want other people know the
camera is transferring data.
Power LED
Switch the LED light of this Internet Camera on or off.
Log
User can check the system log information of the device, including the
Main Info, Appended Info, Operator IP, and so on …
Reload
Click this button; user can refresh the log information of the device.
6.3.2. Date & Time
User can setup the time setting of Internet Camera, make it synchronized with PC or remote NTP
server. Also, you may select the correct time zone of your country.
48
User’s Manual of ICA-2200
Server Date & Time
Displays the date and time of the device
PC Time
Displays the date and time of the connected PC
Adjust
Synchronize
with PC:
Click this o ption to enabl e time synch ronization
with PC time
Manual setting:
Click this option to set time and date manually
Synchronize
with NTP:
Click this o ption if you wa nt to synch ronize the
device’s date and time with those of time serve r
called NTP server (Network Time Protocol)
NTP server name
Type the ho st name or I P address or domain na me of the NTP
server.
NTP sync. Interval
Select an i nterval between 1 an d 23 hours at which you want to
adjust the device’s time referring to NTP server
Time zone
Set the time differen ce from Green wich Mean Time in the area
where the device is installed.
Daylight saving
Check this item to enable daylight saving adjustment.
Daylight Saving
Sets up the date and time of daylight saving start time.
Start Time
Daylight Saving
Stop Time
Sets up the date and time of daylight saving stop time.
49
User’s Manual of ICA-2200
Daylight Saving
Sets up the date of daylight saving offset.
Offset
6.3.3. Maintenance
Default Settings
(Include the network
setting)
Recall the d evice hard factory default settings. Note that click
this button will reset all device’s parameters to the factory
settings (including the IP address).
Default Settings
(Except the network
setting)
The unit is restarte d and most cu rrent settings a re reset to
factory default val ues. This action will not reset the network
setting.
Backup Setting
To take a ba ckup of all of the par ameters, click this button. If
necessary, it will then be possible to return to the previou s
settings, if settings are cha nged and there is u nexpected
behavior.
Restore Setting
Click the “Browse” button to loc ate the s aved backup file and
then click the “Restore Setting” b utton. The settings will be
restored to the previous configuration.
Firmware upgrade
The device supports new firmware upgrade.
1. Close all other application programs which are not necessary for firmware
update.
2. Make sure that only you access this device at this moment
50
User’s Manual of ICA-2200
3. Disable Motion Detection function.
4. Select “Firmware name”
5. Select the Firmware binary file.
Note :
That it must make sure that the Firmware only applies to this device, once
update, it will be burned into FLASH ROM of system.
6. Once the firmware file was selected, select “Upgrade”.
7. The upgrade progress information will be displayed on the screen.
8. A message will be shown while the firmware upgraded. Once the upgrading
process completed, the device will reboot the system automatically.
9. Please wait for 80 seconds, and then you can use PLANET IP Wizard II to
search the device again.
Warning!!!
The download firmware procedure cannot be interrupted. If the power and/or network
connection are broken during the download procedure, it might possibly cause
serious damage to the device.
Please be aware that you should not turn off the power during updating the firmware
and wait for finish message.
Furthermore, do not try to upgrade new firmware if it’s not necessary.
System Restart
The device is restarted without changing any of the settings.
51
User’s Manual of ICA-2200
6.4. Video
This device provides 2 modes of video profile. The first one is 720P mode which supports
video resolution up to H D (1920x720). The second one is 2MP mode which supports
video resolution up to Full HD (192 0x1080). User only can select either 720P or 2MP
modes to operate the camera. Switching between 720P and 2MP mode, the device will
take time to reboot system.
6.4.1. Common
Video Profile
User can only choose either 720P or 2MP modes. 720P mode can
serve streams up to 1920x720 resolutions maximum. On the other
hand, 2MP mode, it can streams up to 1920x10 80 resolutions
maximum.
Text Overlay Setting
There are some impo rtant information can be e mbedded into
image, including date, time, and/or text.
52
User’s Manual of ICA-2200
6.4.2. Video Profile
User can modify the detail parameter for each video profiles in this page.
Name
To assign a name to the selected profile.
Video Type
Video codec of the selected profile.
Resolution
Resolution of the selected profile.
ROI
Assign the selected profile as a ROI stream or not. (Only available
for the profiles with max resolution)
Rate Control
Defines the rate control method of this p rofile. There are four
options: Constant Bit Rate (CBR), Variable Bit Rate (VBR),
Enhanced Constant Bit Rate (ECB R), and Enhanced Variable Bit
Rate (EVBR).
For CBR, the video bit rate is between low to high bandwidth based
on different resolutions. User can set the de sired bit rate to match
the limitation of bandwidth.
For VBR, user should choose the quality level to set the video quality
rather than b it rate. The quality level is betwe en 1 and 100. The
higher value can reach the better qua lity but of course will consum e
53
User’s Manual of ICA-2200
higher bandwidth.
For ECBR, the video bitrates is b ased on norm al CBR mode.
However, the target bitrates can be increased to max target bitrates
while lots of motion in vid eo. The m ax target bitrates will keep a
pre-defined time period and then back to normal CBR bitrates.
For EVBR, the video bit rates is based on norm al VBR mode.
However, the target bitrates can be increased to max target bitrates
while lots of motion in vid eo. The m ax target bitrates will keep a
pre-defined time period and then back to normal VBR mode.
Max Frame Rate
Defines the targeted frame rate of this profile. For example, set the
frame rate to 15 fps, then the image will be update d for 15 fram es
per second. User can set the de sired max frame rate versus video
quality under the limited bandwidth.
GOP Control
Defines the Intra/Inter-frame (I/P) ra tio of this profile. For examp le,
set the GOP to 30, then th e video stream will have one Intra-fram e
every 30 frames.
Multicast
Enable or disable the multicast function.
Multicast Video
IP address and port for multica st video strea ming of the selected
profile.
Multicast Audio
IP address and port for multicast audio streaming of the sele cted
profile
Always
Multicast
Multicast streaming is always enabled or by request
Enable
Warning!!!
To enable the multicast streaming, you should make sure your Intranet does support
multicast function. Otherwise, your Intranet may encounter network storm seriously
due to the video/audio broadcast.
54
User’s Manual of ICA-2200
6.4.3. ROI
ROI means Region of Interest. Use this page to specify loca tion of ROI windows. Only the
maximum resolution profiles can be defined as ROI. In this model, the default ROI win dows are
profile 4 and 5.
6.5. Audio Configuration
55
User’s Manual of ICA-2200
Audio
To enable or disable audio function.
Audio type
To select G711 or G726 for audio coding.
Audio Mode
To select Simplex or Full duplex (2-way audio) mode.
Input Gain
To adjust gain of input audio.
Output Gain
To adjust gain of output audio.
6.6. User Privilege Access Configuration
Use this menu to set the u ser names and password of the Administrator and up to 10 users, and
access right of each user.
Viewer Login
Select “Anonymous” to allow any one viewing the video once
connected. Otherwise, only users in d atabase can view the
video after login.
Access Right
Administrator can access every fun ction in thi s device.
PTZ Control
Authorize this user to control PTZ function or not.
Add, Modify, and Delete of
Users account
However, Viewers only can view the video and acce
limited function.
Manage the user’s account of viewer user.
56
ss
User’s Manual of ICA-2200
6.7. E-Mail Configuration
You may setup SMTP mail param eters for further operation of Event Schedul e. That’s, if users
want to send the alarm m essage out, it will need to configure parameters here and also add at
least one event schedule to enable event triggering.
SMTP Server
Type the SMTP server name or the IP address of the SMTP server.
Test
Send a test mail to mail server to check this account is available or
not.
SMTP Port
Set port number of SMTP service.
SSL
Enable SSL function or not.
Select the authentication required when you send an e-mail.
SMTP Authentication
Disable: If no authentication is required when an e-mail is send.
Enable: If authentication is required when an e-mail is sent.
Authentication
Name
User
Type the user name for the SMTP server if Authentication is Enable.
Authentication Password
Type the password for the SMTP server if Authentication is Enable.
E-mail From
Type the sen der’s E-mail address. This address is use d for repl y
e-mails.
E-mail To
Type the receiver’s e-mail address.
E-mail Subject
Type the subject/title of the e-mail.
57
User’s Manual of ICA-2200
6.8. Object Detection
Use this m enu to spe cify motion dete ction window 1 to win dow 4 a nd set the co nditions for
detection while observing a captured image.
To add or delete the motion windo ws. User can specify up to 4
Included and/or Excluded windows to monitor the video ca ptured by
this device. By draggin g mouse on the image, you can chan ge the
position and size of the selected motion window accordingly.
Add and Delete
Included
Window
or
Excluded
These windows can be specified as Included or Excluded type.
Included:
Windows target specific areas within the whole video image
Excluded:
Windows define areas within an In clude window that should be
ignored (areas outside Include windows are automatically ignored)
Name
Name of the specified motion window.
Object Size
Defines the object size of motion detection. The higher object size will
only larger objects trigger motion detection. The lower object size will
even small objects trigger motion detection too. Generally speaking,
the smaller size will be easier to trigger event.
Sensitivity
Defines the sensitivity value of motion detection. The higher value will
be more sensitivity.
58
User’s Manual of ICA-2200
6.9. Storage Configuration
This page shows the stat us of attache d SD ca rd and Samba server. You m ay setup rela ted
parameters to manage the attached SD card or Samba server also.
6.9.1. SD Card
Enable automatic disk cleanup
Delete old recorded files while the con ditions are reached as
below.
Remove recordings order than
Delete old files by days.
Remove oldest recordings when
disk is
Delete old files by left capacity.
Lock disk
Lock the SD card. Once SD card is locked, all files can’t be
deleted.
59
User’s Manual of ICA-2200
6.9.2. SAMBA Server
This page shows the st atus of SAM BA server. You may setup related parameters to
manage the remote SAMBA server.
Host
Type the SAMBA server domain name or the IP address of the
SMTP server.
Share
Type the sh are folder of remote SAMBA server which the
camera will upload files to this space.
User name
Delete old files by left capacity.
Password
Type the password for the remote SAMBA server.
60
User’s Manual of ICA-2200
6.10. Continuous Recording
The camera can continu ously record video stream into files and save them to attache d
SD card or remote SAMBA server.
Continuous Recording
Record File Type
DISK
Path
Restart
Enable or disable this function.
Choose a video profile to record.
Save recorded files to SD card or remote SAMBA server.
Define the folder path for the recorded files.
Be careful, click this button
will delete all continuous files
recorded in SD card or remote SAMBA server.
6.11. Recording List
6.11.1. Recording List
This page only shows the event recording files which stored in SD card. User may play or
delete the selected file.
61
User’s Manual of ICA-2200
6.11.2. Continuous Recording List
This page only shows the continuous recording files which stored in SD card or re mote
SAMBA server. User may play or delete the selected file.
62
User’s Manual of ICA-2200
6.12. Event Server Configuration
6.12.1. FTP Server
You may setup FTP para meters for further ope ration of Event Schedule. That’s, if users want to
send the alarm message to an FTP server, it will need to configure parameters here and also add
at least one event schedule to enable event triggering as SMTP.
Name
User can specify multiple FTP paths as wish. Therefore, user
needs to specify a name for each FTP setting.
FTP Server
Type the server name or the IP address of the FTP server.
Test
Check the FTP server whether this account is available or not.
FTP Login name
Type the user name for the FTP server.
FTP Login Password
Type the password for the FTP server.
FTP Port
Set port number of FTP service.
FTP Path
Set working directory path of FTP server.
FTP Passive Mode
Select passive or active mode connecting to FTP server.
63
User’s Manual of ICA-2200
6.12.2. TCP Server
In addition to send video file to FTP serv er, the device also can send event message to specified
TCP server.
Name
User can specify multiple TCP servers as wish. Therefore, user
needs to specify a name for each TCP server setting.
TCP Server
Type the server name or the IP address of the TCP server.
TCP Port
Set port number of TCP server.
64
User’s Manual of ICA-2200
6.12.3. HTTP Server
The device also can send event message to specified HTTP server.
Name
User can specify multiple HTTP se rvers as wish. Therefore, user
needs to specify a name for each HTTP server setting.
URL
Type the server name or the IP address of the HTTP server.
Test
Check the HTTP server whether it is available or not.
HTTP Login name
Type the user name for the HTTP server.
HTTP Login Password
Type the password for the HTTP server.
Proxy Address
Type the server name or the IP address of the HTTP Proxy.
Proxy Login name
Type the user name for the HTTP Proxy.
Proxy Login Password
Type the password for the HTTP Proxy.
Proxy Port
Set port number of Proxy.
65
User’s Manual of ICA-2200
6.12.4. SAMBA Server
The device also can send video stream to specified SAMBA server. Most of the time, the SAMBA
server will be another PC or NAS server.
Name
User can specify multiple HTTP se rvers as wish. Therefore, user
needs to specify a name for each HTTP server setting.
SAMBA Server
Type the server name or the IP address of the SAMBA server.
Test
Check the SAMBA server whether this account is available or not.
SAMBA Login name
Type the user name for the SAMBA server.
SAMBA Login Password
Type the password for the SAMBA server.
SAMBA Path
Set working directory path of SAMBA server.
66
User’s Manual of ICA-2200
6.13. Event Schedule Configuration
This menu is used to specify the schedule of Event or Schedule Trigger and activate the
some actions provided by this device. W here the Schedule Trigger will be act ivated by
user-define interval without event happened.
Name
Name of the Event or Schedule.
Enable
Enable or disable this Event or Schedule.
Type
Schedule start with Event trigger or Schedule trigger.
Enable Time
Define the feasible time slot.
Trigger by
Select the triggered sources with event trigger.
Record
Prefix
Define the prefix of recorded filename
Action
File
Define the actions once event triggered.
67
User’s Manual of ICA-2200
Example1.
Send file to FTP server by motion triggered always:
Step 1 Select event trigger
Step 2 Enable time: start from 00:00 to 24:00 every day
Step 3 Trigger by: Motion Area (Added in Object Detection page)
Step 4 Action: Send FTP (Add in Event Server -> FTP Server page)
68
User’s Manual of ICA-2200
Example2.
Send file to E-Mail server by motion triggered from Friday 18:00 to Saturday 06:00
Step 1 Select event trigger.
Step 2 Enable time: start from Friday 18:00 and keep work in 12 hours, so it will stop on Saturday
06:00.
Step 3 Trigger by: Motion Area (Added in Object Detection page)
Step 4 Action: Send e-mail (Add in E-Mail page)
i.
To email address: You need to input the receiver email address.
ii.
Subject: You could specify the email subject.
iii.
Message: You could specify the email content.
69
User’s Manual of ICA-2200
Example3.
Enable Voice Alert every 10-minute during 18:00 to 24:00 from Monday to Friday.
Step 1 Type: Select schedule trigger and interval is 10-minute.
Step 2 Enable Time: Select Monday to Friday, and set start time from 18:00 and keep work in 6
hours.
Step 3 Trigger by: You do not need to choose it, because this will be triggered every minute.
Step 4 Action: Voice Alert.
70
User’s Manual of ICA-2200
6.14. Record Configuration
User can choose the type of record file for event or schedule application.
Record File Type
Choose AVI or JPEG file format for record file.
Record File Prefix
Define the prefix of recorded filename.
Pre-Trigger Duration
Define the maximum duration of pre-alarm.
Best Effort Duration
Define the best effort duration of post-alarm.
Max File Size
Define the maximum buffer size of record file.
71
User’s Manual of ICA-2200
6.15. Port Status
User can check the status of digital input and output (DIDO).
Input Status
Show either inactive or active.
Output Status
Show either inactive or active.
72
User’s Manual of ICA-2200
Chapter 7. PLANET DDNS
Application
1. Configure PLANET DDNS steps:
Step 1 Enable DDNS option through accessing web page of ICA-2200.
Step 2 Select on DDNS server provide, and register an account if you do not use yet.
Let’s take dyndns.org as an example. Register an account in http://planetddns.com
73
User’s Manual of ICA-2200
Chapter 8. Alarm I/O
Connector
Some features of the Camera ca n be activated by an external senso r that sense s physical
changes in the area device is monitoring. These changes can include intrusion detection or certain
physical change in the monitored area. For examples, the external sensor can be a door switch or
an infrared motion detector. These devices are customer provided, and are available from dealers
who carry surveillance and securi ty products. Electrically, they must be able to provide a
momentary contact closure.
This device provides a general I/O terminal block with one digital input and one output for device
control. Pin 2 and 3 can be connected to an external sensor. The input voltage will be monitored
from the initial state ‘LOW’. If the external sensor need 12VDC power, then it can connect to Pin1
(50mA maximum). The Alarm Output of pin 3 and 4 can be used to turn on or off the ext ernal
device. The pin5 and 6 are connected to RS485 interface.
I/O Connector
Pin
Function
1
12VDC power supply (50mA maximum)
2
Digital Input
3
GND
4
Alarm Output
5
RS485 data +
6
RS485 data -
User can refer to the schematic below to make a proper connection between I/O connector and
external sensor and output device.
74
User’s Manual of ICA-2200
Explanation of External I/O Circuit Diagram:
CAUTION!
• THE LOW VOLTAGE/CURRENT CIRCUI TS AND HIGH VOLTAGE/ CURRENT
CIRCUITS ARE IN
THE NE TWORK CAMERA CIRCUIT. THE QUALIFIED
ELECTRICIAN SHOULD DO THE WIRING NOT BY YOURSELF. INCORRECT WIRING
COULD DAMAGE NWTWORK CAMERA. YOU COULD RECEIVE THE F ATAL
ELECTRIC SHOCK.
• THE EXTERNAL I/O IS NOT CAPABLE OF CONNECTING DIRECTLY TO DEVICES
THAT REQUIRE L ARGE AMOUNTS OF CURRENT. I N SOME CASES, A CUSTOM
INTERFACE CIRCUIT (CUSTOMER PROVIDED) MAY HAVE TO BE USED. SERIOUS
DAMAGE TO NETWORK CAMERA MAY RESULT IF A DEVICE IS CONNECTED TO
THE EXTERNAL I/O THAT EXCEEDS ITS ELECTRICAL CAPABILITY.
75
User’s Manual of ICA-2200
Chapter 9. PING IP Address
The PING (stands for Packet Internet Groper) command i s used to d etect whether a
specific IP address is accessible by sending a packet to the specific address and waiting
for a reply. I t’s also a very useful tool to confirm the device installed or if the IP address
conflicts with any other devices over the network.
If you want to make sure the IP address of
follows:
the device, utilize the PING comman d as
z
Launch a Command Prompt.
z
Type ping x.x.x.x, where x.x.x.x is the IP address of the device. For example,
ping 192.168.0.20
The replies, as illustrated below, will provide an explanation to the problem.
If you want to detect any other devices conflicts with the IP address of Network Camera,
also can utilize the PING command but you must disconnect the Camera from the
network first.
76
User’s Manual of ICA-2200
Chapter 10. Bandwidth
Estimation
The frame rate of video transmitted from the device depends on connection band width
between client and server, video resolution, codec type, and quality setting of server.
Here is a guideline to help you roughly estimate the bandwidth requirements for your
device.
The required bandwidth depends on content of video source. The slow motion video will
produce smaller bit rate generally and fast motion will produce higher bit rate vice versa.
Actual results generated by the device may be varying.
Image
Resolution
160 x 80
320 x 176
640 x 352
1920 x 1080
Average range of
data sizes for JPEG
mode
3 ~ 6k byte per
frame
8 ~ 20k byte per
frame
20 ~ 50K byte per
frame
200 ~ 500k byte per
frame
Average bit rate for
MPEG4 mode
Average bit rate for
H.264 mode
64kbps~256kbps
@ 30fps
256kbps~768kbps
@ 30fps
512kbps~3072kbps @
30fps
-
32kbps~192kbps
@ 30fps
192kbps~512kbps
@ 30fps
384kbps~1536kbps
@ 30fps
1536kbps~10000kbps
@ 25fps
Note: Audio streaming also takes bandwidth around 32kbps.
Some
xDSL/Cable modem upl oad speeds could not even reach up to 128 kbps.
Thus, you may not be able to receive good quality video while also streaming
audio on a 128 kbps or lower connection. Even though the upload sp eed is
more than 128kbps, for optimal video performance, disabling audio streaming
will get better video performance.
77
User’s Manual of ICA-2200
Chapter 11. Configure Port
Forwarding Manually
The device can be used with a router. If the device wants to be accessed from the WAN, its IP
address needs to be setup as fixed IP address, also the port forwarding or Virtual Server function
of router needs to be setup. This device supports UPnP traversal function. Therefore, user could
use this feature to configure port forwarding of NAT router first. However, if use r needs to
configure port forwarding manually, please follow the steps as below:
Manually installing the device with a router on your network is an easy 3–step procedure as
following:
1. Assign a local/fixed IP address to your device
2. Access the Router with Your Web browser
3. Open/Configure Virtual Server Ports of Your Router
1. Assign a local/fixed IP address to your device
The device must be assigned a local and fixed IP Ad dress that allows it to be reco gnized by the
router. Manually setup the device with a fixed IP address, for example, 192.168.0.100.
2. Access the Router with Your Web browser
The following steps g enerally apply to any rout er that you have on your net work. The PLANET
WNRT-620 is used as an example to clarify the configuration process. Configure the initial settings
of the router by following the steps outlined in the router’s Quick Installation Guide.
If you have cable or DSL service, you will most likely have a dynamically assigned WAN IP
Address. ‘Dynamic’ means that your router’s WAN IP address can change from time to time
depending on your ISP. A dynamic WAN IP Address identifies your router on the public network
and allows it to access the Internet. To find out what your router’s WAN IP Address is, go to the
Status screen on your router and locate the WAN information for your router. As shown on the
following page the WAN IP Address will be listed. This will be the address that you will need to
type in your web browser to view your camera over the Internet. Be sure to uncheck the Reset IP
address at next boot button at the top of the screen after modifying the IP address. Failure to do
so will reset the IP address when you restart your computer.
78
User’s Manual of ICA-2200
Your WAN IP Address will be listed here.
3. Open/set Virtual Server Ports to enable remote image viewing
The firewall security features built into the rout er and most routers prev ent users from accessing
the video from the device over the Inte rnet. The router connects to the Internet over a serie s of
numbered ports. The ports normally used by the device are blocked from access over the Internet.
Therefore, these ports need to be made accessible over the Internet. This is accomplished using
the Virtual Server function on the router. The Virtual Serv er ports used by the came ra must be
opened through the router for remote access to your camera.
Follow these steps to configure your router’s Virtual Server settings
z
Click Enabled.
z
Enter a unique name for each entry.
z
Select Both under Protocol Type (TCP and UDP)
z
Enter your camera’s local IP Address (e.g., 192.168.0.100, for example) in the Private
IP field.
z
If you are using the def ault camera port settings, enter
80 into the Public and
Private Port section, click Add.
A check mark appearing before the entry name will indicate that the ports are enabled.
79
User’s Manual of ICA-2200
NOTE
Some ISPs block access to port 80. Be sure to check with your ISP so that you can
open the appropriate ports accordingly. If your ISP does not pass traffic on port 80, you
will need to change the port the camera uses from 80 to something else, such as 8080.
Not all routers are the same, so refer to your user manual for specific instructions on
how to open ports.
Enter valid ports in the Virtual Server section of your router. Please make sure to check the box
on this line to enable settings. Then the device can be access from WAN by the router’s WAN IP
Address.
By now, you have finished your entire PC configuration for this device.
80
User’s Manual of ICA-2200
Chapter 12. Power Line
Frequency
COUNTRY
Argentina
VOLTAGE FREQUENCY
220V
50 Hz
COMMENTS
*Neutral and line wires are reversed from that used in
Australia and elsewhere.
*Outlets typically controlled by adjacent switch.
Australia
230V*
50 Hz
Though nominal voltage has been officially changed to 230V,
240V is within tolerances and commonly found.
Austria
230V
50 Hz
*127V found in states of Bahia, Paran?(including Curitiba),
Brazil
110/220V*
60 Hz
Rio de Janeiro, S緌 Paulo and Minas Gerais (though 220V
may be found in some hotels). Other areas are 220V only,
with the exception of Fortaleza (240V).
Canada
120V
60 Hz
China, People's Republic of
220V
50 Hz
Finland
230V
50 Hz
France
230V
50 Hz
Germany
230V
50 Hz
Hong Kong
220V*
50 Hz
India
230V
50 Hz
Italy
230V
50 Hz
*Eastern
Japan
100V
50/60 Hz*
Japan
50
Hz
Kawasaki,
Sapporo,
Yokohoma, and Sendai); Western Japan 60 Hz (Osaka,
Kyoto, Nagoya, Hiroshima)
81
(Tokyo,
User’s Manual of ICA-2200
Malaysia
240V
50 Hz
Netherlands
230V
50 Hz
Portugal
230V
50 Hz
Spain
230V
50 Hz
Sweden
230V
50 Hz
Switzerland
230V
50 Hz
Taiwan
110V
60 Hz
Thailand
220V
50 Hz
*Outlets typically controlled by adjacent switch.
United Kingdom
230V*
50 Hz
Though nominal voltage has been officially changed to 230V,
240V is within tolerances and commonly found.
United States of America
120V
60 Hz
82
User’s Manual of ICA-2200
Chapter 13. 3GPP
To use the 3GPP fun ction, in ad dition to previous section, you
might need more
information or configuration to make this function work.
Note: that to use the 3GPP function, it strongly recommends to install the
Networked Device with a public and fixed IP address without any firewall
protection.
RTSP Port:
Port 554 is the default for RTSP service. Howe ver, sometimes, some service providers
change this port number for some reasons.
If so, u ser needs to change this port
accordingly.
Dialing procedure:
1. Choose a verified player (PacketVideo or Realplayer currently)
2. Use the following URL to access:
rtsp://host/mpeg4/media.3gp
Where host is the host name or IP address of the camera.
Compatible 3G mobile phone:
Please contact your dealer to get the approved list of compatible 3G phone.
83
User’s Manual of ICA-2200
Chapter 14. Troubleshooting
& Frequently Asked Questions
Question
Answer or Resolution
Features
The video and audio
The device utilizes H.264, MPEG4 and JPEG triple
codec is ad opted in th e compression to providing high quality images. Where H.264
and MPEG4 are standards for video compression and JPEG
device.
is a standard for image compression.
The audio codec is defined as G.711/G.726 for RTSP
streaming.
The maximum number of The maximum number of users is limited to 20. However, it
users
accesses
the also depends on the total bandwidth accessed to this device
device simultaneously.
from clients. The maximum data throughput of the device is
around 100~200Mbps for UDP mode and 50Mbps for HTTP
mode. Therefore, the actual number of connected clients is
varying by streaming mode, settings of resolution, codec type,
frame rate and bandwidth. Obviously, the performance of the
each connected client will slow down when many users are
logged on.
The device can be used The device is weatherproof.
outdoors or not.
Install this device
Status LED does not
• Check and confirm that the DC power adaptor, included in
light up.
packaged, is used. Secure the power connector and re-power
it on again.
• If the problem is not solved, the device might be faulty.
Contact your dealer for further help.
The network cabling is
The device uses Category 5 or better UTP cable allowing 10
required for the device.
Base-T, 100 Base-TX, or 1000 Base-T networking.
The
If a firewall exists on the network, port 80 is open for ordinary
device will be
installed and work if
firewall exists on
a data communication. The HTTP port and RTSP port need to
the be opened on the firewall or NAT router.
84
User’s Manual of ICA-2200
network.
The
username
and Username = admin and Password = admin.
password for the fir st Note that it’s all case sensitivity.
time
or a fter
factory
default reset
Forgot
the username
and password
Follow the steps below.
1. Restore the factory default setting by pressing and holding
down more than 5 seconds on the device.
2. Reconfigure the device.
Forgot the IP address of
Check IP address of device by using the PLANET IPWizard II
the device.
program or by UPnP discovery.
PLANET IPWizard II
• Re-power the device if cannot find the unit within 1 minutes.
program cannot find the
• Do not connect device over a router. IPWizard II program
device.
cannot detect device over a router.
• If IP address is not assigned to the PC which running
IPWizard II program, then IPWizard II program cannot find
device. Make sure that IP address is assigned to the PC
properly.
• Antivirus software on the PC might interfere with the setup
program. Disable the firewall of the antivirus software during
setting up this device.
• Check the firewall setting of your PC or Notebook.
Internet Explorer does
Make sure that your Internet Explorer is version 6.0 or later. If
not seem to work well
you are experiencing problems, try upgrading to the latest
with the device
version of Microsoft’s Internet Explorer from the Microsoft
webpage.
PLANET IPWizard II
• Network may have trouble. Confirm the parameters and
program fails to save the
connections of the device.
network parameters.
UPnP NAT Traversal
Cannot work with NAT
• Maybe NAT router does not support UPnP function. Please
router
check user’s manual of router and turn on UPnP function.
• Maybe UPnP function of NAT router is not compatible to the
IP camera. Please contact your dealer to get the approval
85
User’s Manual of ICA-2200
routers list.
Some IP cameras are
• Maybe too many IP cameras have been installed on the
working but others are
LAN, and then NAT router is out of resource to support more
failed
cameras. You could turn off and on NAT router to clear out of
date information inside router.
Access this device
Cannot access the login
• Maybe the IP Address of the Network Camera is already
page and other web
being used by another device or computer. To confirm this
pages of the Network
possible problem, disconnect the Network Camera from the
Camera from Internet
network first, and then run the PING utility to check it out.
Explorer
• May be due to the network cable. Try correcting your
network cable and configuration. Test the network interface by
connecting a local computer to the Network Camera via a
crossover cable.
• Make sure the Internet connection and setting is ok.
• Make sure enter the IP address of Internet Explorer is
correct. If the Network Camera has a dynamic address, it may
have changed since you last checked it.
• Network congestion may prevent the web page appearing
quickly. Wait for a while.
The IP address and Subnet Mask of the PC and Network
Camera must be in the same class of the private IP address
on the LAN.
• Make sure the http port used by the Network Camera,
default=80, is forward to the Network Camera’s private IP
address.
• The port number assigned in your Network Camera might
not be available via Internet. Check your ISP for available
port.
• The proxy server may prevent you from connecting directly
to the Network Camera, set up not to use the proxy server.
• Confirm that Default Gateway address is correct.
• The router needs Port Forwarding feature. Refer to your
router's manual for details.
• Packet Filtering of the router may prohibit access from an
86
User’s Manual of ICA-2200
external network. Refer to your router's manual for details.
• Access the Network Camera from the Internet with the global
IP address of the router and port number of Network Camera.
• Some routers reject the global IP address to access the
Network Camera on the same LAN. Access with the private IP
address and correct port number of Network Camera.
• When you use DDNS, you need to set Default Gateway and
DNS server address.
• If it’s not working after above procedure, reset Network
Camera to default setting and installed it again.
• If the problem is not solved, the Network Camera might be
faulty. Contact your dealer for further help.
Image or video does not
• The first time the PC connects to Network Camera, a pop-up
appear in the main page.
Security Warning window will appear to download ActiveX
Controls. When using Windows XP, or Vista, log on with an
appropriate account that is authorized to install applications.
• Network congestion may prevent the Image screen from
appearing quickly. You may choose lower resolution to reduce
the required bandwidth.
Check the device’s
Go to C:\Windows\Downloaded Program Files and check to
ActiveX is installed on
see if there is an entry for the file “IPCamera Control”. The
your computer
status column should show “Installed”. If the file is not listed,
make sure your Security Settings in Internet Explorer are
configured properly and then try reloading the device’s home
page. Most likely, the ActiveX control did not download and
install correctly. Check your Internet Explorer security settings
and then close and restart Internet Explorer. Try to browse
and log in again.
Internet Explorer
Setup the IE security settings or configure the individual
displays the following
settings to allow downloading and scripting of ActiveX
message: “Your current
controls.
security settings prohibit
downloading ActiveX
controls”.
The device work locally
• Might be caused from the firewall protection. Check the
87
User’s Manual of ICA-2200
but not externally.
Internet firewall with your system or network administrator.
The firewall may need to have some settings changed in order
for the device to be accessible outside your LAN.
• Make sure that the device isn’t conflicting with any other web
server running on your LAN.
• Check the configuration of the router settings allow the
device to be accessed outside your local LAN.
• Check the bandwidth of Internet connection. If the Internet
bandwidth is lower than target bit rate, the video streaming will
not work correctly.
The unreadable
Use the operating system of the selected language. Set the
characters are
Encoding or the Character Set of the selected language on
displayed.
the Internet Explorer.
Frame rate is slower
• The traffic of the network and the object of the image affect
than the setting.
the frame rate. The network congestion causes frame rate
slower than the setting.
• Check the bandwidth of Internet connection. If the Internet
bandwidth is lower than target bit rate, the video streaming will
not work correctly.
• Ethernet switching hub can smooth the frame rate.
Blank screen or very
• Your connection to the device does not have enough
slow video when audio is
bandwidth to support a higher frame rate for the streamed
enabled.
image size. Try reducing the video streaming size to 160x120
or 320x240 and/or disabling audio.
• Audio will consume 32 kbps. Disable audio to improve video.
Your Internet connection may not have enough bandwidth to
support streaming audio from the device.
Image Transfer on e-mail • Default Gateway and DNS server address should be set up
or FTP does not work.
correctly.
• If FTP does not work properly, ask your ISP or network
administrator about the transferring mode of FTP server.
Pan/Tilt does not work.
• Click [Refresh] on the Internet Explorer when the
(including Click to Center communication stops with the device. The image will refresh.
and Preset Positioning)
• Other clients may be operating Pan/Tilt.
88
User’s Manual of ICA-2200
• Pan/Tilt operation has reached the end of corner.
Pan/Tilt does not work
There may be a slight delay when you are using the Pan/Tilt
smoothly.
feature in conjunction with streaming audio and video. If you
find that there is a significant delay while panning or tilting the
camera, try disabling the audio streaming and/or reducing the
video streaming size.
Video quality of the device
The focus on the
• The lens is dirty or dust is attached. Fingerprints, dust, stain,
Camera is bad.
etc. on the lens can degrade the image quality.
The color of the image is
• Adjust White Balance.
poor or strange.
• To insure the images you are viewing are the best they can
be, set the Display property setting (color quality) to 16bit at
least and 24 bit or higher if possible within your computer.
•The configuration on the device image display is incorrect.
You need to adjust the image related parameters such as
brightness, contrast, hue and sharpness properly.
Image flickers.
• Wrong power line frequency makes images flicker. Make
sure the 50 or 60Hz format of your device.
• If the object is dark, the image will flicker. Make the condition
around the Camera brighter.
Noisy images occur.
The video images might be noisy if the device is located in a
very low light environment. Make the condition around the
camera brighter or turn the IR LED on.
Miscellaneous
Cannot play the
Have installed Microsoft’s DirectX 9.0 or later and use the
recorded ASF file
Windows Media Player 11.0 or later to play the AVI filed
recorded by the Device.
89
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement