User Guide

User Guide
TABLE OF CONTENTS
1. Safety Instruction
2. Technical Specification
2.1 Inserting/Exchanging rotating gobos
2.2 Beam angel
3. Lamp
4. How To Set The Unit
4.1 Control Panel
4.2 Main Function
5. How To Control The Unit
5.1 Master/Slave Built-In Preprogrammed Function.
5.2 Universal DMX Controller
5.3 DMX512 Configuration
5.4 DMX512 Connection
6. Troubleshooting
MH-6616S
MH-666S
7. Fixture Cleaning
User Guide
Professional Entertainment Technology
1A
1. Safety Instruction
Warning
y
moisture.
Please read carefully the instruction, which includes important
information about the installation, usage and maintenance.
WARNING
y
Please keep this User Guide for future consultation. If you sell the unit to another user,
be sure that they also receive this instruction booklet.
y
Unpack and check carefully there is no transportation damage before using the unit.
y
Before operating, ensure that the voltage and frequency of power supply match the
To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
y
Never touch bulb with bare fingers as it is very hot after using.
y
Hot lamp explosion hazard. Do not open the unit within five minutes after switching off.
y
Do not start on the unit without bulb enclosure or housing are damaged.
y
The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
y
Do not look directly at the light while the bulb is on.
power requirements of the unit.
Caution
y
Change with the same type of lamp.
y
It’s important to ground the yellow/green conductor to earth in order to avoid electric
repairs yourself. In the unlikely event your unit may require service, please contact your
shock.
y
The unit is for indoor use only. Use only in a dry location.
y
The unit must be installed in a location with adequate ventilation, at least 50cm from
adjacent surfaces. Be sure that no ventilation slots are blocked.
y
Disconnect main power before fuse/lamp replacement or servicing.
y
Replace fuse/lamp only with the same type.
y
Make sure there are no flammable materials close to the unit while operating, as it is fire
nearest dealer.
Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is
firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure
to which you are attaching the unit is secure and is able to support a 12 times weight of the
unit ( Below drawing is for MH-6616S only ).
hazard.
y
There are no user serviceable parts inside the unit. Do not open the housing or attempt any
Use safety cable when fixes this unit. Don’t handle the unit by taking its head only, but
always by taking its base.
y
Maximum ambient temperature is Ta : 40℃. Don’t operate it where the temperature is
higher than this.
y
Unit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool
down before replacing bulb or serving.
y
In the event of serious operating problem, stop using the unit immediately. Never try to
repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or
malfunction. Please contact the nearest authorized technical assistance center. Always
use the same type spare parts.
y
Don’t connect the device to any dimmer pack or power pack.
y
Do not touch any wire during operation as high voltage might be causing electric
2A
3A
2. Technical Specification
Dimension: 360mm x 397mm x 503mm (MH-6616S)
373mm x 295mm x 451mm (MH-666S)
Power supply
- AC 120V~60Hz or 230V/240V/250V 50/60Hz
Weight: 26 kg (MH-6616S)
13 kg (MH-666S)
Lamp
- Discharge lamp MSD 250/2 GY 9.5 (MH-6616S)
- Discharge HIT 150W GY 9.5 (MH-666S)
2.1 Inserting/Exchanging rotating gobos
Optical system
- Standard 13° focused beam angle.
DANGER!
- MH-6616S: Focus adjustable by DMX control.
Install the gobos with the device switched off only.
Shutter
Unplug from mains before changing gobos!
- Strobe speed variable(1~10 flashes per second).
Open the cover by loosening the fastening screw at the sides of the cover.
Gobo wheel
If you wish to use other forms and patterns as the standard-gobos, or if the gobos are to be
- Independent gobo wheel with 6 gobos plus open, gobos are interchangeable: 3 metal
exchanged, remove the fixation ring with an appropriate tool. Remove the gobo and insert
gobos, 2 glass gobos, and 1 effect gobo.
the new gobo. Press the fixation-ring together and insert it in the front of the gobo.
- Gobo wheel rotates with variable speed, giving shaking effect.
Color wheel
- Independent color wheel with 9 dichroic mirrors plus white.
- Color wheel rotates with variable speed, giving rainbow effect.
Movement
- Pan: 540° in 2.8 second.
- Tilt: 270° in 1.6 second.
DMX Channels
- Standard DMX512 signal addressing and can be controlled by any universal DMX
controller.
CAUTION!
Never unscrew the screws of the rotating gobo as the ball bearing
MH-6616S
MH-666S
Channel 1
Pan motion
Pan motion
Channel 2
Tilt motion
Tilt motion
Channel 3
Shutter/ Shaking
Shutter/ Shaking
Channel 4
Gobo
Gobo
Channel 5
Color
Color
Channel 6
Gobo Rotation
Gobo Rotation
Channel 7
——
——
Channel 8
Focus
4A
will otherwise be opened!
2.2 Beam angel
5A
3. Lamp
4. How To Set The Unit
In case of replacement of the lamp or maintenance, do not open the
4.1 Control Panel
fixture within 15 minutes until the unit cools down after switching off.
Because of its high internal pressure, there might be a risk that the Discharge lamp
would explode during operation. The lamp emits intense UV radiation which is harmful
to the eyes and skin. The high luminance of the arc can
cause severe damage to the retina if looks directly at
the lamp.
Discharge lamp : MSD 250/2 (MH-6616S)
HIT 150W (MH-666S)
Display
1. Always switch off the main supply and never handle
To show the various menus and the selected functions .
the lamp or luminaries when is hot.
LED
2. Do not touch the bulb with bare hands. If this happens,
DMX
On
DMX input present
clean the lamp with denatured alcohol and wipe it with
MASTER
On
Master Mode
a lint free cloth before installation.
SLAVE
On
Slave Mode
SOUND
Flashing
Sound activation
3. The lamp generates UV radiation. Never operate the
lamp without appropriate shielding.
Button
4. When burning, the lamp operates at high pressure and
MENU
To select the programming functions
there is a slight risk of arc tube rupture. The risk
DOWN
To go backward in the selected functions
increases with age, temperature and improper handling
UP
To go forward in the selected functions
of the lamp. Do not use the lamp any longer than its
ENTER
To confirm the selected functions
specified life.
5. Make sure the lamp is located in the center of the reflector for the
best spot. Adjust lamp position by screws A, B and C.
MH-6616S
Sensitivity
To adjust the sound sensitivity .
Microphone
To receive audio signal for sound activation .
DMX input/output
For DMX512 link, use 3-pin XLR plug cable to link the unit together.
MH-666S
6A
7A
4.2 Main Function
Show Mode
To select any of the pre-set functions, press the MENU button up to when the required one
Press the MENU button up to when the
is shown on the display. Select the function by ENTER button and the display will blink. Use
ENTER button and the display will blink. Use DOWN and UP button to select the
DOWN and UP button to change the mode. Once the required mode has been selected,
(show 1) or
press the ENTER button to setup or it will automatically return to the main functions without
mode has been selected, press the ENTER button to setup or automatically return to the
any change after idling 8 seconds. To go back to the functions without any change press the
main functions without any change after 8 seconds. To go back to the functions without any
MENU button. The main functions are shown below:
change press the MENU button again.
(show 2) or
is showing on the display. Pressing
(show 3) or
(show 4) mode. Once the
Show 1 mode - Fixture is placed on the floor. Tilt movement angle 210°.
Show 2 mode - Fixture is fixed under ceiling. Tilt movement angle 90°.
Show 3 mode - Fixture is placed on the speaker, The spot is always projecting
to the audience’s direction; i.e in front of the stage. Pan movement angel ( left to
right to left ): 160°. Tilt movement angel: 90° ( 60° above horizon; 30°
below horizon.)
Show 4 mode - Fixture is fixed under ceiling. The spot is mainly projecting in
front of the stage. Pan movement angel ( left to right to left ) :160°.
Tilt
movement angel: 90° ( vertically, front 75°; back 15° )
Slave Mode
is showing on the display. Pressing
Press the MENU button up to when the
ENTER button and the display will blink. Use DOWN and UP button to select the
(2 light show) mode. Once the mode has been selected, press the
(normal) or
ENTER button to setup or automatically return to the main functions without any change
after 8 seconds. To go back to the functions without any change press the MENU button
again.
Blackout Mode
DMX512 Address Setting
Press the MENU button up to when the
Press the MENU button up to when the
is showing on the display. Pressing
is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
ENTER button and the display will blink. Use DOWN and UP button to change the DMX512
(yes blackout) or
address. Once the address has been selected, press the ENTER button to setup or
the ENTER button to setup or automatically return to the main functions without any change
automatically return to the main functions without any change after 8 seconds. To go back to
after 8 seconds. To go back to the functions without any change press the MENU button
the functions without any change press the MENU button again.
again.
8A
(no blackout) mode. Once the mode has been selected, press
9A
is blinking on the display. Use the ENTER button to change to the mode
when the
Color Mode
(display inversion), It will automatically store after 8 seconds. Or press the ENTER
Press the MENU button up to when the
is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(normal) or
(split color) mode. Once the mode has been selected, press the
ENTER button to setup or automatically return to the main functions without any change
button again return to the mode
(display normal). To go back to the functions press
the MENU button.
Display normal mode for the fixture putting on the floor.
Display inversion mode for the fixture fixing under ceiling.
after 8 seconds. To go back to the functions without any change press the MENU button
Focus Adjust
again.
is blinking on the display. Pressing ENTER
Press the MENU button up to when the
Pan Inversion
button, the unit will focus on tilt 90°, and then the unit will focus on pan 0°, pan 90°, pan 180°,
is showing on the display. Pressing
Press the MENU button up to when the
ENTER button and the display will blink. Use DOWN and UP button to select the
(normal) or
pan 270° in every pressing ENTER button. Use DOWN and UP button to adjust focus. To go
back to the functions press the MENU button again.
(pan inversion) mode. Once the mode has been selected, press the
ENTER button to setup or automatically return to the main functions without any change
Self-Test
is blinking on the display. Pressing ENTER
after 8 seconds. To go back to the functions without any change press the MENU button
Press the MENU button up to when the
again.
button and the unit will run self-test by built-in program. To go back to the functions press the
MENU button again.
Tilt Inversion
is showing on the display. Pressing
Press the MENU button up to when the
Fixture Hours
is blinking on the display. Pressing ENTER
ENTER button and the display will blink. Use DOWN and UP button to select the
Press the MENU button up to when the
(normal) or
button and the display will show the number of working hours of the unit. To go back to the
(tilt inversion) mode. Once the mode has been selected, press the
ENTER button to setup or automatically return to the main functions without any change
functions press the MENU button again.
after 8 seconds. To go back to the functions without any change press the MENU button
Reset
again.
is blinking on the display. Pressing ENTER
Press the MENU button up to when the
button and all channels of the unit will return to their standard position. To go back to the
Led Display
Press the MENU button up to when the
is showing on the display. Pressing
functions press the MENU button again.
ENTER button and the display will blink. Use DOWN and UP button to select the
(Led on) or
(Led off) mode. Once the mode has been selected, press the ENTER
button to setup or automatically return to the main functions without any change after 8
seconds. To go back to the functions without any change press the MENU button again.
5. How To Control The Unit
You can operate the unit in three ways:
1. By master/slave built-in preprogram function
2. by universal DMX controller
Display Inversion
It is good for you to install the unit on the floor or under ceiling. Press the MENU button up to
10A
11A
No need to turn the unit off when you change the DMX address, as new DMX address
5.3 DMX512 Configuration
setting will be effected at once. Every time you turn the unit on, it will show type on the
* MH-666S without Channel 8 – Focus.
display and move all the motors to their ‘home’ position and you may hear some noises for
about 20 seconds. After that the unit will be ready to receive DMX signal or run the built-in
programs.
5.1 Master/Slave Built-In Preprogrammed Function
in
(yes blackout) or
(no blackout)
You can select blackout mode
mode while the unit is turned on. By linking the units in master/slave connection, the first unit
will control the other units to give an automatic, sound activated, synchronized light show.
This function is good when you want an instant show. You have to select
(show 1)
or
(show 2) or
(show 3) or
(show 4) mode by easy controller. Its
DMX input jack will have nothing plugged into it, and Its master LED will be constantly on
and sound LED will flash to the music. The other units will have to set in slave mode
and select
(normal) or
(2 light show) mode, Their DMX cables
plugged into the DMX input jacks (daisy chain) and the slave LED lights will constantly on.
2-light show
In
(slave mode),
means the unit works normally and
means
2-light show. In order to create a great light show, you can set
on the second unit to
get contrast movement to each other, even if you have two units only.
5.2 DMX Controller
Use universal DMX controller to control the units, you have to set DMX address from 1 to
512 channel so that the units can receive DMX signal.
Press the MENU button up to when the
is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to change the DMX512
address. Once the address has been selected, press and keep ENTER button pressed up to
when the display stops blinking or storing automatically 8 seconds later. To go back to the
functions without any change press the MENU button again. Please refer to the following
diagram to address your DMX512 channel for the first 4 units.
NOTE: Shutter function is viable only when the value of channel 4 is between 0 and 18.
12A
13A
5.4 DMX512 Connection
6. Troubleshooting
The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.
Following are a few common problems that may occur during operation. Here are
some suggestions for easy troubleshooting:
A. The unit does not work, no light and the fan does not work
1. Check the connection of power and main fuse.
2. Measure the mains voltage on the main connector.
3. Check the power on LED.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and
DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB
of the unit or the previous one.
4. Try to use another DMX controller.
5. Check if the DMX cables run near or run alongside to high voltage cables that may
1. If you use a controller with 5 pins DMX connector, you need to use a 5 to 3 pin adapter.
2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120-ohm
1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in
cause damage or interference to DMX interface circuit.
C. Some units don’t respond to the easy controller
1. You may have a break in the DMX cabling. Check the LED for the response of the
master/ slave mode signal.
the DMX-output of the last unit.
3. Connect the unit together in a “daisy chain” by XLR plug from the output of the unit to the
input of the next unit. The cable can not branched or split to a “Y” cable. DMX512 is a
2. Wrong DMX address in the unit. Set the proper address.
D. No response to the sound
very high-speed signal. Inadequate or damaged cables, soldered joints or corroded
1. Make sure the unit does not receive DMX signal.
connectors can easily distort the signal and shut down the system.
2. Check microphone to see if it is good by tapping the microphone
4. The DMX output and input connectors are pass-through to maintain the DMX circuit,
when power is disconnected to the unit.
E. One of the channels is not working well
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
5. Each lighting unit needs to have an address set to receive the data sent by the controller.
The address number is between 0-511 (usually 0 & 1 are equal to 1).
2. The motor’s drive IC on the PCB might be out of condition.
F. The lamp is cutting out intermittently
6. The end of the DMX512 system should be terminated to reduce signal errors.
1. The lamp is not working well. Check the main voltage either too high or too low.
7. 3 pin XLR connectors are more popular than 5 pins XLR.
2. Internal temperature may be too high. Check and if necessary replace the fan on the
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
head.
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
14A
15A
7. Fixture Cleaning
G. If The MH-6616S pan belt is broken
1. Turn off the main power.
The cleaning of internal and external optical lenses and/or mirrors must be carried out
2. Unscrew all the screws (A) and open the base-housing cover (B).
periodically to optimize light output. Cleaning frequency depends on the environment in
3. Unplug all the connect wires (C) that from the arm to PC board and igniter.
which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater
4. Unscrew the screws (D) that fix the bridge (E).
accumulation of dirt on the unit’s optics.
5. Unscrew the screws (F) that fix the axis gear (G).
6. Change a new belt (H) by going through all connecting wires that from the arm to base,
and through the bridge for correct position.
7. Set up the gear axis to the bridge and screwed it. Note: do not press the belt.
8. Put the belt around the axis gear and motor gear.
Clean with soft cloth using normal glass cleaning fluid.
y
Always dry the parts carefully.
y
Clean the external optics at least every 20 days. Clean the internal optics at least every
30/60 days.
9. Plug all the connect wires (C) that form the arm to PC board and igniter.
10. Adjust the pan home position.
11.Screw the base-housing cover (B).
16A
17A
Technical Specifications
MH-6616S
EC Declaration of Conformity Power
AC 120V~60Hz or AC 230/240/250V 50/60Hz
Fuse
20mm Glass T10A Fast Blow
Lamp
MSD 250/2
Dimension 360mm x 397mm x 503mm
We declare that our products (lighting equipments) comply with the following
Weight
26 kg
specification and bears CE mark in accordance with the provision of the
Electromagnetic Compatibility (EMC) Directive 89/336/EEC.
MH-666S
EN55014-2: 1997 A1:2001, EN61000-4-2: 1995; EN61000-4-3:2002;
Power
AC 120V~60Hz or AC 230/240/250V 50/60Hz
Fuse
20mm Glass T6.3A Fast Blow
Lamp
HIT 150W
EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6:1996,
EN61000-4-11: 1994.
&
Dimension 373mm x 295mm x 451 mm
Harmonized Standard
Weight
13 kg
EN60598-1: 2000+ALL:2000+A12:2002
Safety of household and similar electrical appliances
Part 1 : General requirements
Innovation , Quality , Performance
18A
19A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement